The formula for conversion of ppm to mass concentration is as follows: Mass concentration = PPM × (Molecular mass/24.45)The molecular mass of ozone is 48 g/mol. Hence, the mass concentration of 6 ppm of ozone in air would be calculated as:Mass concentration = 6 × (48/24.45) g/m³ Mass concentration = 11.70 g/m³2. The process by which an organism keeps its body temperature within a specific range in relation to the thermal environment is known as thermoregulation.
Thermoregulation is essential for the optimal functioning of living organisms. Thermoregulation is a vital function that enables organisms to maintain homeostasis by keeping their body temperatures within a specific range in relation to the thermal environment. Thermoregulation is a critical process in both endothermic and exothermic organisms. The physiological and behavioral adaptations that are necessary for thermoregulation vary between different organisms.
3. Instruments used to measure the physical parameters of air temperature, air velocity, and relative humidity to calculate Predicted Mean Vote (PMV) are:
Air Temperature: Air temperature can be measured using thermometers. A few types of thermometers are Alcohol Thermometers, Liquid-in-glass thermometers, Digital thermometers, etc.
Air Velocity: Air Velocity can be measured using Anemometers, hot wire Anemometers, thermal Anemometers, etc.
Relative Humidity: Relative humidity can be measured using Hygrometers, Psychrometers, Dewpoint Hygrometers, etc.
Two precautions that should be observed when using an instrument: A thermometer should be handled with caution, and it should not be subjected to shock or rapid temperature changes that could cause it to break. Psychrometers should be carefully handled, and the wick should be thoroughly soaked in distilled water before use.
To know more about thermoregulation, visit:
https://brainly.com/question/31716751
#SPJ11
EXAMPLE 9.4 A parallel-plate capacitor with plate area of 5 cm² and plate separation of 3 mm has a voltage 50 sin 10't V applied to its plates. Calculate the displacement current assuming 28 8 =
The displacement current in a parallel-plate capacitor with plate area of [tex]5 cm^2[/tex] and plate separation of 3 mm having a voltage of [tex]50 sin 10't V[/tex] applied to its plates, assuming ε = [tex]8.85x10^-^1^2 C^2 N^-^1 m^-^2[/tex], is [tex]14.54 nA[/tex].
The formula to find the displacement current [tex](I_d)[/tex] in a parallel-plate capacitor is given as:
I_d = εA(dV/dt), where ε is the permittivity of free space, A is the area of the plates, d is the distance between the plates, and dV/dt is the rate of change of voltage with time. In this case, plate area (A) =[tex]5 cm^2[/tex] = [tex]5 x 10^-^4 m^2[/tex], plate separation (d) = [tex]3 mm[/tex] = [tex]3 x 10^-^3 m[/tex], voltage (V) = [tex]50 sin 10't V[/tex].
The rate of change of voltage with time [tex](dV/dt) = 50 x 10 cos 10't V/s[/tex]
Using the given value of ε = [tex]8.85 x 10^-^1^2 C^2 N^-^1 m^-^2[/tex], the displacement current is calculated as:
[tex]I_d[/tex] = [tex](8.85x10^-^1^2 C^2 N^-^1 m^-^2) x (5 × 10^-^4 m^2) x (50x10 cos 10't V/s) / (3 x 10^-^3 m)[/tex]
= [tex]14.54 nA[/tex] (approx)
Therefore, the displacement current in the given parallel-plate capacitor is [tex]14.54 nA[/tex]
Learn more about displacement current here:
https://brainly.com/question/33192313
#SPJ11
A parallel-plate capacitor has a capacitance of c 1
=6.5μF when full of air and c 2
=35μF when full of a dielectric oil at potential difference of 12 V. Take the vacuum permittivity to be ε o
=8.85×10 −12
C 2
/(N⋅m 2
). △33% Part (a) Input an expression for the permittivity of the oil ε. ε=
The permittivity of the oil (ε) in the parallel-plate capacitor is approximately 4.65 * 10⁻¹¹ C² / (N * m²), determined by comparing the capacitances when the capacitor is filled with air and dielectric oil.
The permittivity of a material is a measure of its ability to store electrical energy in an electric field. It is denoted by the symbol ε. In this question, we are given the capacitance of a parallel-plate capacitor when it is filled with air (c₁ = 6.5 μF) and when it is filled with a dielectric oil (c₂ = 35 μF) at a potential difference of 12 V.
To find the permittivity of the oil (ε), we can use the formula for capacitance:
C = ε * A / d
where C is the capacitance, ε is the permittivity, A is the area of the plates, and d is the separation between the plates.
Let's consider the case when the capacitor is filled with air. We can rearrange the formula to solve for ε:
ε₁ = C₁ * d / A
where ε₁ is the permittivity when the capacitor is filled with air.
Now, let's consider the case when the capacitor is filled with the dielectric oil. Again, we can rearrange the formula to solve for ε:
ε₂ = C₂ * d / A
where ε₂ is the permittivity when the capacitor is filled with the dielectric oil.
We are given the values of C₁, C₂, and the potential difference, and we can assume that the area of the plates and the separation between them remain constant.
Substituting the given values into the formulas, we have:
ε₁ = (6.5 * 10⁻⁶ F) * d / A
ε₂ = (35 * 10⁻⁶ F) * d / A
We can divide the second equation by the first equation to eliminate d/A:
ε₂ / ε₁ = (35 * 10⁻⁶ F) / (6.5 * 10⁻⁶ F)
Simplifying this expression, we get:
ε₂ / ε₁ ≈ 5.38
Now, we can substitute the known value of ε0 (the vacuum permittivity) into the equation:
ε₂ / ε₁ = ε₂ / (8.85 * 10⁻¹² C² / (N * m²))
Simplifying further, we find:
ε₂ ≈ 5.38 * (8.85 * 10⁻¹² C² / (N * m²))
Calculating this expression, we get:
ε₂ ≈ 4.65 * 10⁻¹¹ C² / (N * m²)
Therefore, the permittivity of the oil (ε) is approximately 4.65 * 10⁻¹¹ C² / (N * m²).
To know more about parallel-plate capacitor, refer to the link below:
https://brainly.com/question/30900528#
#SPJ11
3. Tentbook problem \( 2.16 \) PROBLEM 2.16. The rod AMCD is tade of an aluminum for which \( 2=70 \) OPa. Por the loadery samen, determine the defiection of (a) paint \( A,(b) \) point \( D \)
The given rod is AMCD made of aluminum with the modulus of elasticity of E=70 GPa. The deflection of point D is 0.13 mm.
The load applied is such that the deflection of the rod has to be calculated at points A and D respectively.
(a) Deflection at point A:
Let P be the load acting at point A.
Let the deflection at point A be δ.
Then, from the theory of elasticity,δ = PL/2AEQ 2.16
Thus,δ = 20 × 0.75^3/(2 × 70 × 10^3 × (π/4) × 0.75^4)
= 0.195 mm
Therefore, the deflection of point A is 0.195 mm.
(b) Deflection at point D:Let the deflection at point D be δ.Then, from the theory of elasticity,
δ = PL/3AEQ 2.16
Thus,
δ = 20 × 0.75^3/(3 × 70 × 10^3 × (π/4) × 0.75^4)
= 0.13 mm
Therefore, the deflection of point D is 0.13 mm.
To learn more about aluminum visit;
https://brainly.com/question/28989771
#SPJ11
X-ray ---Describe the major components of an induction motor and
describe how this type of motor works.
An induction motor is a type of AC electric motor in which a rotating magnetic field is produced by the stator winding that then interacts with the current in the rotor windings to produce torque. The major components of an induction motor are the stator, rotor, and air gap.
The stator is the stationary part of the motor and is made up of a series of stacked laminations, which house the stator winding. This winding is usually made up of copper wire and is wound around each of the laminations to create a series of poles. When an AC voltage is applied to the stator winding, a magnetic field is produced that rotates around the circumference of the stator.The rotor, on the other hand, is the rotating part of the motor and is also made up of a series of laminations, which house the rotor winding.
The rotor winding is usually made up of aluminum or copper bars and is short-circuited at the ends with the help of end rings. When the magnetic field produced by the stator rotates around the rotor, it induces a current in the rotor winding that then produces a magnetic field, which interacts with the magnetic field produced by the stator to produce torque.The air gap is the space between the stator and rotor and is critical for the operation of the motor. The gap must be small enough to allow for maximum magnetic flux density but large enough to prevent the rotor from making contact with the stator during operation.
To know more about torque visit:
https://brainly.com/question/30338175
#SPJ11
There is a concentric sphere with an inner conductor radius of 1 [m] and an outer conductor diameter of 2 [m] and an outer diameter of 2.5 [m], and the outside of the outer concentric sphere is grounded. Given a charge of 1 [nC] on the inner conductor, suppose that the charge is distributed only on the surface of the conductor, find (a),(b),(c)
(a) What [V] is the electric potential of the radius 0.7 [m] position?
(b) What [V] is the electric potential of the radius 2.3 [m] position?
(c) What [V] is the electric potential of the radius 3.0 [m] position?
a) The electric potential at the radius 0.7 [m] position is approximately 1.285 x [tex]10^1^0[/tex]V,
(b) The electric potential at the radius 2.3 [m] position is approximately 3.913 x 10^9[tex]10^9[/tex] V.
(c) The electric potential at the radius 3.0 [m] position is 0 V.
To find the electric potential at different positions within the concentric sphere system, we can use the formula for electric potential due to a charged conductor. The electric potential at a point is given by:
V = k * Q / r
where V is the electric potential, k is the electrostatic constant (k = 8.99 x [tex]10^9 Nm^2/C^2[/tex]), Q is the charge, and r is the distance from the center of the conductor.
(a) To calculate the electric potential at the radius 0.7 [m] position, we can use the formula as follows:
V = [tex](8.99 x 10^9 Nm^2/C^2) * (1 x 10^-^9 C) / 0.7[/tex] [m]
V ≈ 1.285 x[tex]10^1^0[/tex] V
Therefore, the electric potential at the radius 0.7 [m] position is approximately 1.285 x [tex]10^1^0[/tex] V.
(b) At the radius 2.3 [m] position, we can again use the formula to find the electric potential:
V = [tex](8.99 x 10^9 Nm^2/C^2) * (1 x 10^-69 C)[/tex] / 2.3 [m]
V ≈ 3.913 x[tex]10^9[/tex]V
So, the electric potential at the radius 2.3 [m] position is approximately 3.913 x [tex]10^9[/tex] V.
(c) Finally, at the radius 3.0 [m] position, we need to consider that the outer conductor is grounded. When a conductor is grounded, its potential is taken as zero. Therefore, the electric potential at the radius 3.0 [m] position is 0 V.
For more such information on: electric potential
https://brainly.com/question/14812976
#SPJ8
Explain the rate of change of voltage of a thyristor in relation to reverse-biased.
The rate of change of voltage of a thyristor in relation to reverse-biased operation is typically high.
When a thyristor is reverse-biased, it is designed to block the flow of current in the opposite direction, acting like an open switch. In this state, the thyristor maintains a high impedance, preventing significant current from flowing through it.
If the reverse voltage across the thyristor exceeds its breakdown voltage, it enters a state called the reverse breakdown region. In this region, the thyristor starts conducting current in the reverse direction, allowing a high current to flow through it. During this transition, the voltage across the thyristor drops rapidly, causing a high rate of change of voltage.
It's important to note that the reverse breakdown region is an undesirable operating condition for a thyristor, as it can lead to damage or failure. Thyristors are typically designed to operate in forward-biased mode, where they exhibit lower voltage drop and better control of current flow.
In summary, when a thyristor is reverse-biased and enters the reverse breakdown region, the rate of change of voltage is high as the thyristor transitions from a high-impedance state to conducting current in the reverse direction.
Know more about Thyristor here:
https://brainly.com/question/33222927
#SPJ11
Please help with 2.3 and 2.4
2.1 Explain the capabilities that a circuit breaker must display during a fault. (3) 2.2 Describe the operation of a circuit breaker under fault conditions. (4) 2.3 Illustrate by means of a sketch the
However, I have provided the answer for 2.1 and 2.2 below:2.1 Capabilities that a circuit breaker must display during a fault:A circuit breaker is an important protective device that is designed to safeguard electrical systems and devices against various faults and overloads.
During a fault, a circuit breaker must display the following capabilities:Quick response: A circuit breaker must be able to respond quickly to a fault and disconnect the affected part of the circuit. This is important to prevent further damage to the electrical equipment or system.Fault isolation: A circuit breaker should be capable of isolating the faulty section of the system or equipment.
This helps in ensuring that the rest of the system remains unaffected by the fault.Reliability: A circuit breaker must be reliable and should be able to perform its function under all conditions.2.2 Operation of a circuit breaker under fault conditions:A circuit breaker is an automatic device that is used to interrupt the flow of current in an electrical circuit in case of an overload or short circuit. When a fault occurs, the circuit breaker operates to isolate the affected section of the circuit and stop the flow of current.
To know more about provided visit:
https://brainly.com/question/9944405
#SPJ11
suppose you have a galvanometer with a full scale current Ic = 50 and an internal resistance r = 200 ohms. What resistance value of a multiplier resistor should be used for making a dc voltmeter with a maximum scale reading Vmax = 20V
The resistance value of the multiplier resistor should be 3990 ohms.
To convert a galvanometer into a voltmeter, a multiplier resistor is connected in series with the galvanometer. The purpose of the multiplier resistor is to limit the current passing through the galvanometer and to scale the voltage being measured.
In this case, we want the maximum scale reading of the voltmeter to be 20V. The galvanometer has a full scale current of 50 and an internal resistance of 200 ohms.
To calculate the resistance value of the multiplier resistor, we can use Ohm's Law and the principle of voltage division. Ohm's Law states that V = IR, where V is the voltage, I is the current, and R is the resistance.
Since the maximum scale reading of the voltmeter is 20V, we can set up the equation as follows:
Vmax = Ic * (Rg + Rm)
Where Vmax is the maximum scale reading, Ic is the full scale current of the galvanometer, Rg is the internal resistance of the galvanometer, and Rm is the resistance of the multiplier resistor.
Substituting the given values, we have:
20 = 50 * (200 + Rm)
Simplifying the equation, we get:
Rm = (20 - 50 * 200) / 50
Calculating the value, we find:
Rm = -3990 ohms
However, resistance cannot be negative, so we take the absolute value:
Rm = 3990 ohms
Learn more:About galvanometer here:
https://brainly.com/question/30922468
#SPJ11
The answer is 76 Ω. because it includes the derivation and calculation process.
To make a DC voltmeter with a maximum scale reading Vmax = 20V using a galvanometer with a full-scale current Ic = 50 and an internal resistance r = 200 ohms, we need a resistor Rm in series with the galvanometer.
The resistance value of this multiplier resistor Rm can be calculated as follows:Vmax = IRm + IcR Where,
Vmax = 20V,
Ic = 50,
R = 200 ohms
Rm = (Vmax - IcR)/I
=(20 - 50×200)/50
=-3800/50
=-76 ΩSo,
the resistance value of the multiplier resistor should be -76 Ω.
However, since it's impossible to have a negative resistor, the value of the resistor should be rounded off to 76 Ω. Hence, the answer is 76 Ω. because it includes the derivation and calculation process.
To know more about resistor visit:-
https://brainly.com/question/22718604
#SPJ11
11.2. Calculate the mean free path λ He of helium gas enclosed in a large jar at STP. Do you expect any difference in the calculated value of λ He If the jar is a cube of side 10cms each.
The mean free path λ He of helium gas enclosed in a large jar at STP can be calculated as 0.262 nm.
Mean free path is the average distance traveled by a molecule between successive collisions. The formula to calculate mean free path is λ= kT/√2πd^2p where, k = Boltzmann constant, T = Absolute temperature, d = Diameter of the molecule, p = Pressure For He gas enclosed in a large jar at STP, the values will be:
k = 1.38 × 10⁻²³ J/K
T = 273 + 0°C = 273 K
d = 2.0 Å (diameter of He molecule)
p = 1 atm = 101.325 kPa= 760 torr
Therefore, λ = (1.38 × 10⁻²³ J/K × 273 K)/(√2π(2.0 × 10⁻¹⁰ m)² × 101.325 kPa)
λHe = 0.262 nm
If the jar is a cube of side 10cm each, the value of mean free path will not change because it depends only on temperature, pressure and molecular diameter.
Learn more about mean free path here:
https://brainly.com/question/32323758
#SPJ11
noving the next question prevents changes to this answer. Question 12 What object temperature would correspond to a black body wavelength peak of 793nm
The wavelength of the peak of radiation of an object is directly proportional to the temperature of the object. Therefore, by using Wien's Law, which states that λmaxT = 2.898 × 10⁻³ m·K, we can find the temperature of the object at which the black body peak is 793 nm.
λmax = 793 nm = 7.93 × 10⁻⁷ m
By substituting λmax and solving for T, we obtain the temperature of the object:
T = 2.898 × 10⁻³ m·K / 7.93 × 10⁻⁷ mT
= 3,654 K
Therefore, the object temperature corresponding to a black body wavelength peak of 793 nm is 3,654 K.
To know more about temperature, visit:
https://brainly.com/question/7510619
#SPJ11
Question 1 In Compton scattering, calculate the maximum kinetic energy given to the recoil electron for a given photon energy
Compton scattering is a physical phenomenon that refers to the interaction between a high-energy photon and a target, typically an electron. It's named after Arthur Holly Compton, who discovered it in 1922.The Compton effect is used in various fields of science, including nuclear physics and astronomy, among others.
Compton scattering is a physical phenomenon that refers to the interaction between a high-energy photon and a target, typically an electron. It's named after Arthur Holly Compton, who discovered it in 1922.The Compton effect is used in various fields of science, including nuclear physics and astronomy, among others. In this phenomenon, the photon loses energy while the electron gains energy and recoils. Compton scattering is an inelastic scattering phenomenon. The formula for calculating the maximum kinetic energy given to the recoil electron for a given photon energy is as follows: KE = Eγ - Eγ' + (Eγ - Eγ')2/mec2
where KE is the kinetic energy of the recoil electron, Eγ is the energy of the incident photon, Eγ' is the energy of the scattered photon, me is the rest mass of the electron, and c is the speed of light. The formula can be rearranged to solve for the maximum kinetic energy of the recoil electron:
KEmax = Eγ/(1 + Eγ/me*c2) - Eγ'/(1 - cosθ)
where θ is the angle between the incident photon and the scattered photon. The maximum kinetic energy given to the recoil electron for a given photon energy can be calculated using the Compton scattering formula. Compton scattering is a physical phenomenon that occurs when a high-energy photon interacts with a target, typically an electron. When this interaction occurs, the photon loses energy while the electron gains energy and recoils. This phenomenon is known as Compton scattering. Compton scattering is an inelastic scattering process.
The formula for calculating the maximum kinetic energy given to the recoil electron for a given photon energy is KE = Eγ - Eγ' + (Eγ - Eγ')2/mec2. The formula can be rearranged to solve for the maximum kinetic energy of the recoil electron, which is KEmax = Eγ/(1 + Eγ/me*c2) - Eγ'/(1 - cosθ).
In this formula, KE is the kinetic energy of the recoil electron, Eγ is the energy of the incident photon, Eγ' is the energy of the scattered photon, me is the rest mass of the electron, c is the speed of light, and θ is the angle between the incident photon and the scattered photon. The maximum kinetic energy of the recoil electron is proportional to the energy of the incident photon and inversely proportional to the rest mass of the electron.
To know more about Compton scattering visit:
https://brainly.com/question/32197116
#SPJ11
There are 2 particle energies. The degeneracies of them are both 4.If there are 4 bosons in the system. What are the possible distributions of the system? What are the number of accessible states of the distributions?
The number of accessible states of distribution 1 is 10, while that of distribution 2 is 20.
In a system consisting of 4 bosons, with 2 energy particles having degeneracies of 4, there are different possible distributions of the system.
The distributions are as follows:
Distribution 1: Two bosons occupy the first energy level, and the other two bosons occupy the second energy level. This distribution has 5 accessible states.
Distribution 2: Three bosons occupy the first energy level, and one boson occupies the second energy level. This distribution has 5 accessible states.
The distribution of bosons obeys the Bose-Einstein distribution formula:
n(E) = 1 / [exp(β(E − µ)) − 1]where n(E) is the number of bosons at energy level E
β is the Boltzmann constant
µ is the chemical potential of the system
E is the energy level.
The total number of accessible states for a system of 4 bosons with 2 energy levels having degeneracies of 4 is given by the expression:
n_total = (n1+n2+3)where n1 and n2 are the numbers of bosons at energy levels E1 and E2, respectively. In distribution 1, n1 = n2 = 2
n_total = (2+2+3) = 10In distribution 2, n1 = 3 and n2 = 1
n_total = (3+1+3) = 20.
To know more about Bose-Einstein please refer to:
https://brainly.com/question/33288941
#SPJ11
A student places a block of hot metal into a coffee cup calorimeter containing 157.5 g of water. The water temperature rises from 21.7 °C to 34.6 °C. How much heat (in calories) did the water absorb? water cal How much heat did the metal lose? 9metal= cal
The water absorbed 3014.25 calories of heat, while the metal lost 3014.25 calories of heat.
When the block of hot metal is placed into the coffee cup calorimeter containing water, heat transfer occurs between the metal and the water until thermal equilibrium is reached. In this process, the water absorbs heat from the metal, causing its temperature to rise. The heat absorbed by the water can be calculated using the formula:
Q = mcΔT
where Q is the heat absorbed, m is the mass of the water, c is the specific heat capacity of water, and ΔT is the change in temperature.
Given that the mass of the water is 157.5 g and the change in temperature is (34.6 °C - 21.7 °C) = 12.9 °C, we can substitute these values into the formula:
Q = (157.5 g) * (1 cal/g °C) * (12.9 °C) = 3014.25 calories
Therefore, the water absorbed 3014.25 calories of heat.
Since energy is conserved, the heat lost by the metal is equal to the heat gained by the water. Therefore, the metal loses the same amount of heat as the water absorbs, which is also 3014.25 calories.
Learn more about Metal
brainly.com/question/28931986
#SPJ11
DETAILS SERPSE10 26.1.P.003. MY NOTES ASK YOUR TEACHER In the Bohr model of the hydrogen atom, an electron in the 8th excited state moves at a speed of 3.42 x 104 m/s in a circular path of radius 3.39 x 10-ºm. What is the effective current associated with this orbiting electron? mA
The effective current associated with the orbiting electron is approximately -2.93 milliamperes (mA).
In the Bohr model of the hydrogen atom, electrons revolve around the nucleus in discrete energy levels or orbits. The 8th excited state refers to the orbit with the highest energy among the excited states.
To find the effective current associated with the orbiting electron, we can use the concept of current as the rate of flow of charge.
The effective current is given by the formula:
I = (q * v) / T,
where I is the current, q is the charge, v is the velocity, and T is the time period of the orbit.
Since the electron has a charge of -1.6 x 10^-19 coulombs (C) and is moving at a speed of 3.42 x 10^4 m/s, we can substitute these values into the formula. However, we need to find the time period first.
The time period (T) can be calculated using the formula:
T = (2 * π * r) / v,
where r is the radius of the orbit.
Substituting the given values, we have:
T = (2 * π * 3.39 x 10^-10 m) / (3.42 x 10^4 m/s).
Simplifying this expression, we find T ≈ 1.86 x 10^-14 s.
Now, substituting the values of q, v, and T into the formula for current:
I = (-1.6 x 10^-19 C * 3.42 x 10^4 m/s) / (1.86 x 10^-14 s).
Evaluating this expression, we find I ≈ -2.93 x 10^-3 A.
Note that the negative sign indicates the direction of the current, which is opposite to the conventional current direction. Therefore, the effective current associated with this orbiting electron is approximately 2.93 milliamperes (mA).
Learn more about Hydrogen
brainly.com/question/30623765
#SPJ11
The outer layer of a 60 Hz power transmission line is made of braided Aluminum wire with conductivity o = 3.8 x 107 S/m and Mr - 1. What is the maximum diameter (d) wire that can be used for which the current flows mostly inside the wires rather than on their surface? (d is approximately equal to the skin depth) = • A. d; Imm. • B. it doesn't matter since Al is a good conductor. • C. d ; lcm. • D. d ; 3mm. • E. d ; 5cm.
The maximum diameter (d) wire that can be used for which the current flows mostly inside the wires is 5cm. The answer is option E, i.e., d ; 5cm.
The maximum diameter (d) wire that can be used for which the current flows mostly inside the wires rather than on their surface is d; 5 cm. Here's how to solve the problem:
Given,Conductivity of braided aluminum wire, σ = o = 3.8 × 107 S/m
Relative Permeability of aluminum wire, Mr = 1
Frequency of the power transmission line, f = 60 Hz
We can find the skin depth using the following formula: δ = √(2/πfμσ)
where μ is the permeability of free space.
The permeability of free space, μ = 4π × 10-7 H/m
Therefore,δ = √[(2/(π × 60 × 4π × 10-7 × 3.8 × 107)]δ ≈ 5 cm
The maximum diameter (d) of the wire for which the current flows mostly inside the wires is approximately equal to the skin depth, which is 5 cm (Option E).
To learn more about current visit;
https://brainly.com/question/31315986
#SPJ11
In a pn junction, under forward bias, the built-in electric field stops the diffusion current Select one: True False
Taking into consideration the Early effect in the npn transistor, we can state tha
1. The given statement "In a pn junction, under forward bias, the built-in electric field stops the diffusion current" is False.
2. The given statement "Taking into consideration the Early effect in the npn transistor, we can state that the collector current I_C decreases with increasing V_CE" is False.
1. In a pn junction under forward bias, the built-in electric field does not stop the diffusion current. Instead, it facilitates the flow of current across the junction. When a pn junction is forward-biased, the p-side (anode) is connected to the positive terminal of a voltage source, and the n-side (cathode) is connected to the negative terminal.
This forward bias reduces the width of the depletion region in the junction, allowing the majority of carriers (electrons in the n-side and holes in the p-side) to easily cross the junction. As a result, diffusion current occurs, where electrons move from the n-side to the p-side, and holes move from the p-side to the n-side.
2. Taking into consideration the Early effect in an NPN transistor, the collector current (I_C) does not decrease with increasing collector-emitter voltage (V_CE). The Early effect, also known as the output or base-width modulation effect, refers to the phenomenon where the collector current is influenced by the variation in the width of the depletion region in the base region of a transistor.
In an npn transistor, increasing the collector-emitter voltage (V_CE) does not directly affect the collector current. However, it does influence the effective base width, which impacts the transistor's current gain (β) and overall characteristics. The Early effect causes a slight decrease in the effective base width with increasing V_CE, resulting in a small increase in the collector current.
The Question was Incomplete, Find the full content below :
1. In a pn junction, under forward bias, the built-in electric field stops the diffusion current Select one: True False
2. Taking into consideration the Early effect in the npn transistor, we can state that the collector current I_C decreases with increasing V_CE. Select one: True False
know more about electric field here:
https://brainly.com/question/19878202
#SPJ8
Your graph of the mechanical energy of the sphere versus time should show evidence of dissipative forces (such as air resistance). How much mechanical energy is dissipated for the sphere in front? (In J)
mechanical
112.728513
120.90598
127.03033
121.742354
119.489706
120.402719
121.894701
115.832518
125.179124
t(s)
0.0333667
0.5005005
0.667334
0.8341675
1.001001
1.1678345
1.334668
1.5015015
1.668335
1.8351685
1.9686353
The mechanical energy dissipated for the sphere in front is 3.104005 J.
To determine the amount of mechanical energy dissipated for the sphere, we need to analyze the change in mechanical energy over time.
The given data provides the mechanical energy values at different time points (t) for the sphere.
Since dissipative forces, such as air resistance, are present, the mechanical energy of the sphere will gradually decrease over time.
To estimate the amount of energy dissipated, we can consider the change in mechanical energy between the initial and final time points.
From the given data, we can see that the initial mechanical energy is 112.728513 J, and the final mechanical energy is 115.832518 J.
To calculate the mechanical energy dissipated, we can find the difference between these two values:
Mechanical energy dissipated = Final mechanical energy - Initial mechanical energy
= 115.832518 J - 112.728513 J
= 3.104005 J
Therefore, the mechanical energy dissipated for the sphere in front is approximately 3.104005 J.
Learn more about mechanical energy from the given link
https://brainly.com/question/24443465
#SPJ11
3. Calculate the declination angle, hour angle, solar altitude angle and solar zenith angle ,azimuth angle at noon on November 15, 2021 for a location at 23.58° N latitude
To calculate the declination angle, hour angle, solar altitude angle, solar zenith angle, and azimuth angle. The calculated values are: Declination Angle (δ): -17.11°, Hour Angle (H): 0°, Solar Altitude Angle (α): 44.84°,Solar Zenith Angle (θ): 45.16°, Azimuth Angle (A): 137.68°.
Declination Angle (δ):
The declination angle represents the angular distance between the Sun and the celestial equator. It varies throughout the year due to the tilt of the Earth's axis. The formula to calculate the declination angle on a specific date is:
δ = 23.45° * sin[(360/365) * (284 + n)],
where n is the day of the year. For November 15, 2021, n = 319.
Calculating the declination angle:
δ = 23.45° * sin[(360/365) * (284 + 319)]
δ ≈ -17.11° (negative sign indicates the position in the southern hemisphere)
Hour Angle (H):
The hour angle represents the angular distance of the Sun east or west of the observer's meridian. At solar noon, the hour angle is 0. The formula to calculate the hour angle is:
H = 15° * (12 - Local Solar Time),
where Local Solar Time is expressed in hours.
Since we are calculating at solar noon, Local Solar Time = 12:00 PM.
Calculating the hour angle:
H = 15° * (12 - 12)
H = 0°
Solar Altitude Angle (α):
The solar altitude angle represents the angle between the Sun and the observer's horizon. It can be calculated using the formula:
α = arcsin[sin(latitude) * sin(δ) + cos(latitude) * cos(δ) * cos(H)],
where latitude is the observer's latitude in degrees.
Calculating the solar altitude angle:
α = arcsin[sin(23.58°) * sin(-17.11°) + cos(23.58°) * cos(-17.11°) * cos(0°)]
α ≈ 44.84°
Solar Zenith Angle (θ):
The solar zenith angle represents the angle between the zenith (directly overhead) and the Sun. It can be calculated using the formula:
θ = 90° - α,
where α is the solar altitude angle.
Calculating the solar zenith angle:
θ = 90° - 44.84°
θ ≈ 45.16°
Azimuth Angle (A):
The azimuth angle represents the angle between true north and the projection of the Sun's rays onto the horizontal plane. It can be calculated using the formula:
A = arccos[(sin(δ) * cos(latitude) - cos(δ) * sin(latitude) * cos(H)) / (cos(α))],
where latitude is the observer's latitude in degrees and H is the hour angle.
Calculating the azimuth angle:
A = arccos[(sin(-17.11°) * cos(23.58°) - cos(-17.11°) * sin(23.58°) * cos(0°)) / (cos(44.84°))]
A ≈ 137.68°
So, at solar noon on November 15, 2021, for a location at 23.58° N latitude, the calculated values are:
Declination Angle (δ): -17.11°
Hour Angle (H): 0°
Solar Altitude Angle (α): 44.84°
Solar Zenith Angle (θ): 45.16°
Azimuth Angle (A): 137.68°
To learn more about, zenith angle, click here, https://brainly.com/question/28147097
#SPJ11
1. Two light sources are used in a photoelectric experiment to determine the work function of a particular metal. When green light of 2 = 546.1 nm is used, the stopping potential of 0.376 V for the photoelectrons is measured. (a) Based on this measurement, what is the work function for this metal? (b) What is the stopping potential if yellow light of λ = 587.5 nm?
The stopping potential of a yellow light with = 587.5 nm is 1.05 V.
The wavelength of green light, λ = 546.1 nm
The stopping potential for photoelectrons, V = 0.376 V
(a) Calculation of work function (Φ)The stopping potential (V) is given by
V = hν/e - Φ
whereh is the Planck's constant = [tex]6.626 * 10^{-34[/tex] Jsν is the frequency of light e is the charge of the electron = 1.6 × 10^-19 CWhen green light of wavelength λ = 546.1 nm is used, The frequency of the light is given by
ν = c/λ wherec is the speed of light = 3 × 10^8 m/s
Substituting the values of c, h, e, λ and V in the equation of stopping potential, we get0.376
= (6.626 × 10⁻³⁴ × 3 × 10^8)/[(1.6 × 10^-19) × 546.1 × 10^-9] - ΦΦ
= (6.626 × 10^-34 × 3 × 10^8)/[(1.6 × 10^-19) × 546.1 × 10^-9] - 0.376Φ
= 4.31 × 10^-19 J
Therefore, the work function of the metal is =[tex]4.31 * 10^{-19[/tex] J.
(b) Calculation of stopping potential for yellow light
The wavelength of yellow light is given by
λ = 587.5 nm
The frequency of yellow light is
ν = c/λ = (3 × 10^8)/(587.5 × 10^-9)
= 5.093 × 10^14 Hz
The stopping potential (V) for yellow light is given by
V = hν/e - Φ = (6.626 × 10^-34 × 5.093 × 10^14)/1.6 × 10^-19 - 4.31 × 10^-19V
= 1.05 V
Therefore, the stopping potential of a yellow light with = 587.5 nm is 1.05 V.
To learn more about wavelength, visit:
https://brainly.com/question/31143857
#SPJ11
A cylindrical capacitor has an inner conductor of radius 2.7 mm and an outer conductor of radius 3.4 mm. The two conductors are separated by vacuum, and the entire capacitor is 3.0 m long. What is the capacitance per unit length? Express your answer in picofarads per meter. The potential of the inner conductor relative to that of the outer conductor is 300mV. Find the charge (magnitude and sign) on the inner conductor. Express your answer with the appropriate units. The potential of the inner conductor relative to that of the outer conductor is 300mV. Find the charge (magnitude and sign) on the outer conductor. Express your answer with the appropriate units.
A) capacitance per unit length is C ≈ 4.376 x 10^-11 F/m
B) charge on the inner conductor is 1.313 x 10^-14 C (positive).
C) charge on the outer conductor is -1.313 x 10^-14 C (negative).
A) To find the capacitance per unit length of the cylindrical capacitor, we can use the formula:
C = 2πε₀/ln(b/a)
Where:
C is the capacitance per unit length
ε₀ is the vacuum permittivity (8.85 x 10^-12 F/m)
b is the outer radius of the capacitor (3.4 mm = 3.4 x 10^-3 m)
a is the inner radius of the capacitor (2.7 mm = 2.7 x 10^-3 m)
Substituting the given values into the formula, we have:
C = (2π x 8.85 x 10^-12 F/m) / ln(3.4 x 10^-3 m / 2.7 x 10^-3 m)
C = (2π x 8.85 x 10^-12 F/m) / ln(1.2593)
C ≈ 4.376 x 10^-11 F/m
B) To find the charge on the inner conductor, we can use the formula:
Q = C x V
Where:
Q is the charge
C is the capacitance per unit length (4.376 x 10^-11 F/m)
V is the potential difference between the inner and outer conductor (300 mV = 300 x 10^-3 V)
Substituting the given values into the formula, we have:
Q = (4.376 x 10^-11 F/m) x (300 x 10^-3 V)
Q ≈ 1.313 x 10^-14 C
The charge on the inner conductor is approximately 1.313 x 10^-14 C (positive).
C) To find the charge on the outer conductor, we can use the fact that the total charge on the system is zero, so the charge on the outer conductor will be the negative of the charge on the inner conductor.
Therefore, the charge on the outer conductor is approximately -1.313 x 10^-14 C (negative).
To learn more about capacitance and Charge Calculation:
https://brainly.com/question/16998502
#SPJ11
Q.EL15-3) Please help me with the solution to this
electromagnetism problem.
Q3】 As shown in Fig. 3(a), there is a toroidal core with permeability \( \mu \). The mean radius of the toroidal core is \( a \), and the cross sectional area of the core is \( A=\pi b^{2} \), where
A toroidal core's inductance is provided by the inductance formula, which is given by[tex]\[L_{S}=N^{2}\mu \pi \left( \frac{b^{2}}{a}[/tex] \right) \]where N is the number of turns of wire around the toroidal core, a is the mean radius of the toroidal core, b is the radius of the wire used to wrap the toroidal core, and μ is the core's permeability. (b) The self-inductance of the toroidal core is \( L_{S}=N^{2}\mu \pi \left( \frac{b^{2}}{a} \right) \). (c) Mutual inductance.
The mutual inductance between two toroidal cores is given by the equation\[tex][M_{21}=\frac{N_{2}N_{1}\mu \pi b_{2}^{2}b_{1}^{2}}{a_{2}+a_{1}}\ln \frac{a_{2}}{a_{1}}\][/tex]where N1 is the number of turns of wire around the first toroidal core, N2 is the number of turns of wire around the second toroidal core, a1 and a2 are the mean radii of the first and second toroidal cores, and b1 and b2 are the radii of the wire used to wrap the first and second toroidal cores,
respectively. (d) The coefficient of coupling. The coefficient of coupling is given by the equation\[k=\frac{M}{\sqrt{L_{1}L_{2}}}\]where M is the mutual inductance between two toroidal cores, and L1 and L2 are the self-inductances of the two toroidal cores, respectively. (e) The equivalent inductance when two coils are wound on the toroidal core. When two coils are wound on a toroidal core, the equivalent inductance is given by\[L_{eq}=\frac{L_{1}L_{2}}{L_{1}+L_{2}+2M}\]
To know more about toroidal visit:
https://brainly.com/question/30025309
#SPJ11
Information signal transmitted is 5sin(26000). Find out the antenna size if the size of the antenna depends on one-tenth of the wavelength of the transmitted signal.
The antenna size is 1153.85 meters (approx).
Given that the information signal transmitted is 5sin(26000) and the size of the antenna depends on one-tenth of the wavelength of the transmitted signal.
We have to find out the antenna size.
Antenna size depends on the wavelength of the transmitted signal and is given by the formula:
Antenna size = (wavelength/10)
Given that the signal transmitted is 5sin(26000).
Therefore, the equation of the transmitted signal is given by:
s(t) = 5sin(2πft)
where
f is the frequency and
t is time.
Substitute the given value of frequency
f=26,000 Hz.
The equation becomes:
s(t) = 5sin(2π(26000)t)
Now, we know that the speed of light
(c) = 3 × 10^8 m/s
The wavelength (λ) can be calculated using the formula:
λ = c/f
λ = (3 × 10^8)/26000
= 11538.46 meters
Therefore, the Antenna size = (wavelength/10)
= 11538.46/10
= 1153.85 meters (approx)
Therefore, the antenna size is 1153.85 meters (approx).
To know more about antenna size visit:
https://brainly.com/question/21292628
#SPJ11
Lighting systems operating at 30 volts or less shall consist of
a(n) ____ power supply, low-voltage luminaires, and associated
equipment that are all identified for the use.
Lighting systems operating at 30 volts or less shall consist of a 600-volt power supply, low-voltage luminaires, and associated equipment that are all identified for use.
These systems may be used in wet locations and other hazardous locations because the voltage is low enough to prevent any serious hazards.
The low voltage wiring shall have a minimum 90° C rating and a minimum 600-volt insulation rating. Transformers, wiring, and other equipment that produce or handle low-voltage circuits shall comply with the National Electrical Code (NEC).
The use of low-voltage systems provides energy savings, and they are more durable than high-voltage alternatives. In addition, they provide enhanced safety, making them an excellent choice for various applications, including residential, commercial, and industrial facilities.
In conclusion, lighting systems operating at 30 volts or less shall consist of a power supply, low-voltage luminaires, and associated equipment that are all identified for use.
These systems are designed for safety, durability, and energy savings, making them ideal for a wide range of applications.
Learn more about Lighting systems from the given link
https://brainly.com/question/19697218
#SPJ11
Unanswered • 3 attempts left A dentist is using a mirror which being 2.1 cm from a tooth creates a direct image of X 3.6 magnification. What is the radius of curvature of this mirror? Give answer in cm. You look at yourself into shiny Christmas ball of diameter 9.9 cm. You face is at distance 22.0 cm from the ball. What is the magnification factor for your face? A small candle is 34.3 cm from a concave mirror having a radius of curvature of 18.9 cm.What is the distance to the image for this setup? Give answer in cm. A mirror is showing upright image of a person standing 1.8 m from it. Image is 2.1 times taller than a person. What is the radius of curvature of this mirror? Give the answer in meters.
A dentist is using a mirror which is 2.1 cm from a tooth creating a direct image of X 3.6 magnification.
The magnification factor is given by:
Magnification factor = v/u = - (p/q)Where v is the image distance,u is the object distance,p is the image height and is the object height. The radius of curvature = 2f = (p+q)²/p = q/(1/p + 1/q) = q/((p+q)/pq)Radius of curvature = 2.1/(1-1/3.6)Radius of curvature = 3.36 cmThe radius of curvature of this mirror is 3.36 cm.
You look at yourself into a shiny Christmas ball of a diameter of 9.9 cm. Your face is at a distance of 22.0 cm from the ball. The magnification factor is given by:
Magnification factor = v/u = - (p/q)Here,p = image height = object height = image distance = object distanceMagnification factor = v/uMagnification factor = - v/q = he/' where he is the image height and h is the object height. Magnification factor = - (h'/h)Magnification factor = - v/q = (s-f)/where s is the distance between the object and the image and f is the focal length.Magnification factor = - v/u = -(22 cm + 9.9 cm)/(22 cm) = - 1.45The magnification factor for your face is -1.45.A small candle is 34.3 cm from a concave mirror having a radius of curvature of 18.9 cm.
the focal length is given by:f = r/2Where r is the radius of curvature image distance is given by:
1/u + 1/v = 1/fu = object distance, and = image distance1/34.3 + 1/v = 1/18.9v = 11.2 cmThe distance to the image for this setup is 11.2 cm. A mirror is showing an upright image of a person standing 1.8 m from it. The image is 2.1 times taller than a person.
the magnification factor is given by: Magnification factor = v/u = - (p/q)For the upright image, the magnification factor is positiveMagnification factor = p/qMagnification factor = v/uMagnification factor = he/' where he is the image height and h is the object height. Magnification factor = - v/q = (s-f)/where s is the distance between the object and the image and f is the focal length.h'/h = 2.1 => h' = 2.1hh = 1.8 m => h = 1.8/2.1 = 0.857 magnification factor = - v/q = (s-f)/magnification factor = 2.1 = v/0.857v = 1.83 the focal length is given by:f = s/(1+1/2.1)f = 1.21 m The radius of curvature of this mirror is: R = 2f = 2 × 1.21 mR = 2.42 the radius of curvature of this mirror is 2.42 m.
To know more about dentist please refer to:
https://brainly.com/question/32077936
#SPJ11
say a solenoid has 103 turns/cm how many turns is that x
turns/meter? how would I generalize this?
The number of turns x per meter (turns/meter) for a solenoid that has 103 turns/cm is 103 turns/meter.
A solenoid has 103 turns per centimeter (103 turns/cm).
To find the number of turns x per meter (turns/meter), we need to generalize this as follows:
If a solenoid has N turns per unit length of a wire (L), then the number of turns x per meter (turns/meter) can be found by using the following formula;x = N / L where; N = number of turns L = unit length of wire to find the value of x (number of turns per meter),
We first need to convert 103 turns/cm to turns/meter, which can be done by multiplying 103 by 100 as follows:103 turns/cm = (103 x 100) turns/m = 10,300 turns/m
Now we can use the above formula to find the value of x;x = N / L = 10,300 / 100 = 103 turns/meter
To know more about solenoids please refer to:
https://brainly.com/question/1873362
#SPJ11
A single phase 220/6 Volt, 50 Hz transformer has a rated primary current = 0.5 A. its maximum efficiency is at load current = 15 A and equal to 94% at unity p.f. Its efficiency at rated load, 0.65 p.f. lagging is:
a) 87.8%.
b) 92.3%.
c) 90.9%.
d) None.
None of the given options (a, b, c) accurately represents the efficiency of the transformer at rated load and a power factor of 0.65 lagging. We can use the given information about the transformer's maximum efficiency and rated primary current. The correct option is D.
To calculate the efficiency of the transformer at a rated load and a power factor of 0.65 lagging, we can use the given information about the transformer's maximum efficiency and rated primary current.
Given:
Rated primary current = 0.5 A
Maximum efficiency = 94% at a unity power factor
Load current at maximum efficiency = 15 A
Efficiency is calculated using the formula:
Efficiency = (Output power / Input power) * 100
At maximum efficiency, the output power is equal to the input power. Therefore, we can write:
Output power at maximum efficiency = Input power at maximum efficiency
Let's denote the input power at maximum efficiency as Pin_max and the output power at rated load and a power factor of 0.65 lagging as Pout_rated.
Now, we can set up the equation:
Pin_max = Pout_rated
Since the efficiency at maximum load and unity power factor is given as 94%, we can write:
0.94 = (Pout_rated / Pin_max) * 100
Solving for Pout_rated / Pin_max:
Pout_rated / Pin_max = 0.94 / 100
Pout_rated / Pin_max = 0.0094
Now, we can calculate the efficiency at the rated load and a power factor of 0.65 lagging:
Efficiency = (Output power / Input power) * 100
Efficiency = (Pout_rated / Pin_rated) * 100
Where Pin_rated is the input power at rated load and a power factor of 0.65 lagging.
We know that:
Pin_max = Pin_rated * Power factor
Substituting the given power factor of 0.65 lagging:
Pin_max = Pin_rated * 0.65
Solving for Pin_rated:
Pin_rated = Pin_max / 0.65
Substituting the value of Pout_rated / Pin_max:
Efficiency = (Pout_rated / (Pin_max / 0.65)) * 100
Efficiency = (Pout_rated / Pin_max) * (100 / 0.65)
Efficiency = (0.0094) * (100 / 0.65)
Efficiency ≈ 1.446 %
Therefore, none of the given options (a, b, c) accurately represents the efficiency of the transformer at rated load and a power factor of 0.65 lagging.
The correct option is D.
To learn more about transformer click here
https://brainly.com/question/16971499
#SPJ11
You connect a battery, resistor, and capacitor as in (Figure 1), where R=17.0Ω and C=5.00×10 −6
F. The switch S is closed at t=0. When the current in the circuit has magnitude 3.00 A, the charge on the capacitor is 40.0×10 −6
C. What is the emf of the battery? Express your answer with the appropriate units. is Incorrect; Try Again; 5 attempts remaining Part B At what time t after the switch is closed is the charge on the capacitor equal to 40.0×10 −6
C ? Express your answer with the appropriate units. When the current has magnitude 3.00 A, at what rate is energy being stored in the capacitor? Express your answer with the appropriate units. Part D When the current has magnitude 3.00 A, at what rate is energy being supplied by the battery? Express your answer with the appropriate units.
The emf of the battery is 51.0 volts, the time when the charge on the capacitor is 40.0×10⁻⁶ C is approximately 0.157 s, the rate at which energy is being stored in the capacitor when the current is 3.00 A is 153 watts, and the rate at which energy is being supplied by the battery when the current is 3.00 A is also 153 watts.
To find the emf of the battery, we can use Ohm's Law. Ohm's Law states that the voltage across a resistor (V) is equal to the current through the resistor (I) multiplied by the resistance (R). In this case, the resistor has a resistance of 17.0 Ω and the current is 3.00 A. Therefore, the voltage across the resistor is:
V = I * R
V = 3.00 A * 17.0 Ω
V = 51.0 V
So, the emf of the battery is 51.0 volts.
To find the time (t) when the charge on the capacitor is equal to 40.0×10⁻⁶ C, we need to use the equation that relates the charge on a capacitor (Q) to the capacitance (C) and the voltage across the capacitor (V). The equation is:
Q = C * V
Rearranging the equation to solve for time (t):
t = Q / (C * V)
t = 40.0×10^(-6) C / (5.00×10⁻⁶ F * 51.0 V)
t = 0.156862745 s
Therefore, when the charge on the capacitor is 40.0×10⁻⁶ C, the time is approximately 0.157 s.
To find the rate at which energy is being stored in the capacitor when the current has magnitude 3.00 A, we can use the formula for the power (P) in a circuit:
P = IV
where I is the current and V is the voltage across the capacitor.
Since the current is 3.00 A and we know the voltage across the capacitor is 51.0 V (calculated earlier), we can calculate the power:
P = 3.00 A * 51.0 V
P = 153 W
Therefore, when the current has magnitude 3.00 A, the rate at which energy is being stored in the capacitor is 153 watts.
Finally, to find the rate at which energy is being supplied by the battery when the current has magnitude 3.00 A, we can use the same formula for power:
P = IV
Since the current is 3.00 A and we know the emf of the battery is 51.0 V (calculated earlier), we can calculate the power:
P = 3.00 A * 51.0 V
P = 153 W
Therefore, when the current has magnitude 3.00 A, the rate at which energy is being supplied by the battery is 153 watts.
To know more about Ohm's Law, refer to the link below:
https://brainly.com/question/14796314#
#SPJ11
please answer this as soon as possible
What characterizes kinetic energy from a mechanical point of view? Gives a brief explanation. Answer: faster movement gives maximun
Kinetic energy refers to the energy an object possesses due to its motion. It is one of the two major types of mechanical energy in the universe, the other being potential energy.
Kinetic energy can be characterized from a mechanical point of view as follows: Kinetic energy is determined by the mass of an object and its velocity. The more massive an object is, the more kinetic energy it has when it is moving at a certain velocity.
In contrast, the faster an object is moving, the more kinetic energy it has when it has a given mass. Faster movement, from a mechanical perspective, results in the maximum kinetic energy that a body can hold. This is because when an object moves quickly, its velocity, mass, and kinetic energy are all positively related. Therefore, if any of these variables increase, the other two must increase as well, and this results in a higher kinetic energy.
To know more about kinetic energy, visit:
https://brainly.com/question/999862
#SPJ11
The Cosmic Microwave Background is remarkable because it a. is emitted by quasars, which are "baby" galaxies b. was discovered by Hubble and showed that all galaxies outside of our Local Group are expanding away from us c. is a perfect blackbody curve and shows no spectral lines d. can only be seen in the X-ray part of the spectrum
The Cosmic Microwave Background (CMB) is remarkable because it is a perfect blackbody curve and shows no spectral lines.
The Cosmic Microwave Background (CMB) is the afterglow of the Big Bang and is one of the strongest pieces of evidence supporting the Big Bang theory. It is not emitted by quasars or discovered by Hubble. The CMB is characterized by a nearly perfect blackbody spectrum, meaning its intensity as a function of wavelength follows a specific pattern, known as Planck's law.
This blackbody curve of the CMB is observed across the microwave part of the electromagnetic spectrum. Unlike other objects in space, the CMB does not exhibit spectral lines, as it represents the homogeneous and isotropic radiation from the early universe, where matter and radiation were tightly coupled.
learn more about microwave click here;
brainly.com/question/2088247
#SPJ11
Q12. A step-down transformer used in the national grid has an input power of 28,000 W and an output power of 23,000 W. a. Calculate the efficiency of the transformer. (2) b. (i) How much power is dissipated due to the heating effect? (ii) If the transformer is used for 3.5 hours, how much energy is wasted during that time? (4)
Energy wasted = power dissipated × time used Energy wasted = 5,000 W × 3.5 hours Energy wasted = 17,500 Wh or 17.5 kWh (4 significant figures)Therefore, the energy wasted by the transformer during 3.5 hours is 17.5 kWh.
A step-down transformer used in the national grid has an input power of 28,000 W and an output power of 23,000 W. a. Calculate the efficiency of the transformer. (2) b. (i) How much power is dissipated due to the heating effect? (ii) If the transformer is used for 3.5 hours, how much energy is wasted during that time?"A transformer is an electric device used to transfer electrical energy from one circuit to another. The input power is given as 28,000 W, and the output power is 23,000 W. The efficiency of the transformer can be calculated as follows:Efficiency
= output power / input power × 100%Efficiency
= 23,000 W / 28,000 W × 100%Efficiency
= 82.14% (2 significant figures)Therefore, the efficiency of the transformer is 82.14%. (a)The power dissipated due to the heating effect is the difference between the input power and the output power.Power dissipated
= input power - output power Power dissipated
= 28,000 W - 23,000 W Power dissipated
= 5,000 W (i)Therefore, the power dissipated due to the heating effect is 5,000 W. (b)The energy wasted by the transformer during 3.5 hours can be calculated by using the formula:E
= P × t where, E is the energy wasted, P is the power dissipated, and t is the time used.Energy wasted
= power dissipated × time used Energy wasted
= 5,000 W × 3.5 hours Energy wasted
= 17,500 Wh or 17.5 kWh (4 significant figures)Therefore, the energy wasted by the transformer during 3.5 hours is 17.5 kWh.
To know more about Energy visit:
https://brainly.com/question/1932868
#SPJ11
