1. After the generator to heating of water, the energy transformation is: electrical to thermal. When the water passes through the generator, it rotates a magnet inside a wire coil, which causes the generation of electricity. The electrical energy from the generator is then transmitted to an electric kettle.
2. The starting form of energy for the water to be boiled is: thermal. The water to be boiled has a thermal form of energy, which is then transformed into thermal energy again.
2.1. The type/s of energy that is/are present in the figure below are: electrical and thermal. Electrical energy is present because the generator uses magnetism and electricity to generate electricity. Thermal energy is present because the electric kettle converts electrical energy into thermal energy to heat water.
To know more about generator visit:
https://brainly.com/question/12841996
#SPJ11
A source r(t) = 8 cos(2π ft) V drives a load that is a parallel combination of a 12 resistor and a 1j 2 inductor (e.g., this combination might model a motor). Answer the following two questions: (a) What is the current supplied by the source as a function of time? (b) What is the phase relationship between the voltage and current?
(a)i(t) = 8 cos(2πft) / 10.909 ∠-5.7107°= 0.732 cos(2πft + 5.7107°) A, (b) the voltage leads the current by 5.7107°
(a)To calculate the current supplied by the source as a function of time, we need to determine the total impedance of the circuit. We can use the following equation to calculate the impedance of the parallel combination of the resistor and inductor:
Z = R || XL= R || jXL= R || j(2πfL)
where R is the resistance (12 Ω), XL is the inductive reactance (j2 Ω), and f is the frequency (100 Hz).
Substituting the given values, we get:
Z = 12 || j2(2π × 100 × 0.002)= 12 || j1.2566= 10.909 ∠-5.7107°V/I
Let us now calculate the current supplied by the source as a function of time:
i(t) = v(t) / Z
where v(t) = 8 cos(2πft) is the voltage supplied by the source.
Substituting the value of Z, we get:
i(t) = 8 cos(2πft) / 10.909 ∠-5.7107°= 0.732 cos(2πft + 5.7107°) A
(b)The phase relationship between voltage and current is given by the phase angle between the two waveforms. Since the voltage and current waveforms are sinusoidal, we can use the following formula to calculate the phase angle:φ = θv - θi
where θv and θi are the phase angles of the voltage and current waveforms, respectively.
Substituting the values, we get:φ = 0° - (-5.7107°)= 5.7107°
Therefore, the voltage leads the current by 5.7107°.
This means that the current waveform lags behind the voltage waveform.
In other words, the current does not instantaneously follow the voltage, but instead takes some time to respond. This is due to the presence of the inductor in the circuit, which causes the current to lag behind the voltage.
To learn more about voltage click here:
https://brainly.com/question/1176850#
#SPJ11
Cow's milk produced near mudear reactions can be tested for an inte s 1.10 por per liter to check for possible reactor leakage. What mass (in g) of lines this activity?
The mass of Iodine-131 in the milk cannot be determined.
Cow's milk produced near mudar reactions can be tested for an inte s 1.10 por per liter to check for possible reactor leakage. To calculate the mass of Iodine-131,
we can use the following formula:
Mass = Activity × time × (1/λ)
Activity (A) = 1.10 Bq/L = 1.10 disintegrations per second per liter.
1 Ci = 3.7 × 10¹⁰ disintegrations/second, 1 Bq = (1/3.7 × 10¹⁰) Ci = 2.70 × 10⁻¹¹ CiSo, 1.10 Bq/L = 1.10 × 2.70 × 10⁻¹¹ Ci/L = 2.97 × 10⁻¹¹ Ci/LWe can also convert Ci/L to g/L
using the following formula:
1 Ci/L = 3.7 × 10⁷ Bq/L = 3.7 × 10⁷ disintegrations per second per liter = (3.7 × 10⁷) × (2.70 × 10⁻¹¹) g/s = 9.99 × 10⁻⁵ g/sWe know that 1 hour = 3600 seconds if we test the milk for 1 hour,
we get Mass = Activity × time × (1/λ) = (2.97 × 10⁻¹¹ Ci/L) × (1 L) × (9.99 × 10⁻⁵ g/s/Ci) × (3600 s) × (1/λ) = (2.97 × 10⁻¹¹) × (9.99 × 10⁻⁵) × (3600/λ) since we do not have the value of λ in the question, we cannot calculate the value of mass.
To know more about disintegrations please refer to:
https://brainly.com/question/31185800
#SPJ11
b) Two cables \( D E \) and \( D H \) are used to support the uniform bent rod \( A B C D \) as shown in Figure Q1. All dimensions are in meters. i) Express the position of point \( D \) relative to t
The position of point D relative to the midpoint of cable DE can be found using the method of moments by expressing the sum of the moments about the midpoint of cable DE.
The forces acting at point D can be resolved into horizontal and vertical components. As the bent rod is in equilibrium, the sum of the horizontal components of the forces is zero. Also, as there is no horizontal component of force acting at point D, the horizontal component of the tension in cable DE is equal and opposite to the horizontal component of the tension in cable DH.
Therefore, the horizontal component of the tension in cable DE is 8cos30 and the horizontal component of the tension in cable DH is -8cos30. The vertical component of the tension in cable DE is equal to the weight of the bent rod and is given by 5g. Also, as there is no vertical component of force acting at point D, the vertical component of the tension in cable DH is equal to the vertical component of the tension in cable DE.
Therefore, the vertical component of the tension in cable DH is 5g/2. T
herefore, the sum of the moments about the midpoint of cable DE is given by
8cos30 x 4 - 5g/2 x 2 + 5g x (2 + x) - 8cos30 x (4 + x) = 0 where x is the distance of point D from the midpoint of cable DE. Solving this equation, we get x = -3.05 m.
Therefore, the position of point D relative to the midpoint of cable DE is 3.05 m to the left of the midpoint of cable DE.
To learn more about cable visit;
https://brainly.com/question/32453186
#SPJ11
What fraction of a radioactive sample remains after one, two, and three half-lives have elapsed?
In 1932, Robert Chadwick irradiated a beryllium target with alpha particles. Analysis showed that the following nuclear reaction had occurred: 2He 4 + 4Be 9 → 6C 12 + X . Balance the reaction and identify the unknown product.
Can carbon-14 be used to estimate the age of a ceramic pot? Explain briefly.
Carbon-14 dating cannot be used to determine the age of a ceramic pot.
For the given radioactive sample, it is required to find what fraction of the radioactive sample remains after one, two, and three half-lives have elapsed.
Given, Half-life of the sample = tLet the initial amount of the radioactive sample be A
After time t1, t2, and t3 the remaining amount of the sample will be A/2, A/2^2 and A/2^3 respectively.
Hence the required fraction of the radioactive sample after one half-life = A/2AHence the required fraction of the radioactive sample after two half-lives = A/2 x 1/2 = A/2^2
Hence the required fraction of the radioactive sample after three half-lives = A/2 x 1/2 x 1/2 = A/2^3
Therefore, the fraction of a radioactive sample that remains after one, two, and three half-lives have elapsed are A/2, A/2^2, and A/2^3 respectively.Given reaction is 2He 4 + 4Be 9 → 6C 12 + X
For balancing the above reaction, the atomic number and mass number should be equal on both sides.
The balanced reaction is: 4He + 9Be → 12C + XThe unknown product is X.
We know that the atomic number of carbon is 6 and mass number is 12.
Therefore, the atomic number of the unknown product is 12 - 6 = 6 and mass number is equal to that of the sum of the mass numbers of 4He and 9Be. i.e. mass number of X = 4 + 9 = 13
No, carbon-14 cannot be used to estimate the age of a ceramic pot.
Carbon-14 is a radioactive isotope that is used to date the remains of once-living organisms.
Ceramic pots are made from clay, which is not a living organism.
Therefore, carbon-14 dating cannot be used to determine the age of a ceramic pot.
Learn more about Carbon-14 dating
brainly.com/question/22184593
#SPJ11
please include numbers and units to avoid confusion
A cylindrical storage tank has a radius of 1.01 m. When filled to a height of 3.30 m, it holds 14700 kg of a liquid industrial solvent. What is the density of the solvent? Number i Units
The density(D) of the solvent is 1381.22 kg/m³. Answer: 1381.22 kg/m³.
Given that the radius of the cylindrical storage tank is 1.01 m, and when it's filled to a height of 3.30 m, it holds 14700 kg of a liquid industrial solvent(LIS). To find the density of the solvent, we use the formula: Density = mass/volume. Here, the volume of the cylindrical tank is given by the formula: V = πr²h, radius(r) and height(h) of the tank. Substituting the values, we get: V = π × (1.01 m)² × (3.30 m)= 10.65 m³Density = mass/volume = 14700 kg / 10.65 m³ = 1381.22 kg/m³.
To know more about liquid industrial solvent visit:
https://brainly.com/question/33394198
#SPJ11
7.) Find the following: a.) A 200-MHz carrier is modulated by a 3.6-kHz signal and the resulting maximum deviation is 5.8 kHz. What is the deviation ratio? b.) What is the bandwidth of the FM signal using the conventional method (Bessel Function)? c.) What is the bandwidth of the FM signal using Carson's rule? d.) Sketch the spectrum of the signal, include all of the significant sidebands and their magnitudes
a. The deviation ratio is the ratio of the frequency deviation of the carrier wave to the modulating signal frequency. The formula for deviation ratio is as follows:
Deviation ratio = Maximum frequency deviation / Modulating signal frequency= 5.8 kHz / 3.6 kHz= 1.61b.
The bandwidth of the FM signal using the conventional method (Bessel Function) is calculated using the following formula:
Bandwidth (B) = 2 ( Δf + fm)Where Δf is the maximum deviation of the carrier frequency from the carrier frequency and fm is the modulating frequency.Bandwidth (B) = 2 ( Δf + fm)= 2 (5.8 kHz + 3.6 kHz)= 19 kHzc. Carson's rule states that the bandwidth of an FM signal is given by the sum of two times the frequency deviation and the highest frequency in the modulating signal, thus:
Bandwidth (B) = 2 × Δf + 2 fmWhere Δf is the maximum deviation of the carrier frequency from the carrier frequency and fm is the modulating frequency.
Bandwidth (B) = 2 × Δf + 2 fm
= 2 × 5.8 kHz + 2 × 3.6 kHz= 16 kHzd.
To know more about deviation visit:
https://brainly.com/question/31835352
#SPJ11
Batteries are rated in terms of ampere-hours (A.h). For example, a battery that can produce a current of 2.00 A for 3.00 h is rated at 6.00 A. h. (a) What is the total energy stored in a 9.0−V battery rated at 56.0 A⋅h ? kWh (b) At se.101 per kilowatt-hour, what is the value of the electricity produced by this battery? 4
The total energy stored in the battery is approximately 5.04 kWh.
The value of the electricity produced by the battery is approximately $0.50904.
a. To find the total energy stored in a battery, we can use the formula:
Energy (in watt-hours) = Voltage (in volts) × Ampere-hours
Given that the voltage of the battery is 9.0 V and it is rated at 56.0 A⋅h, we can calculate the total energy stored as follows:
Energy = 9.0 V × 56.0 A⋅h
To convert the energy to kilowatt-hours (kWh), we divide the energy by 1000:
Energy (in kWh) = (9.0 V × 56.0 A⋅h) / 1000
Performing the calculation, we find:
Energy (in kWh) = 5.04 kWh
Therefore, the entire amount of energy stored in the battery is around 5.04 kWh.
b. To determine the value of the electricity produced by the battery, we multiply the energy in kilowatt-hours (5.04 kWh) by the cost per kilowatt-hour ($0.101):
Value of electricity = 5.04 kWh × $0.101/kWh
Performing the calculation, we find:
Value of electricity = $0.50904
Therefore, the worth of the battery's power is around $0.50904.
To know more about the Battery, here
https://brainly.com/question/14975254
#SPJ4
An industrial load consumes 10 kW at a power factor of 0.80 lagging from a 240-V, 60- Hz, single phase source. A bank of capacitors is connected in parallel to the load to raise the power factor to 0.95 lagging. Find the current drawn from the source. Find the reactive power drawn from the source. Find the apparent power drawn from the source. Find the required reactive power in KVAR to raise the Power factor to 0.95 lagging. Find the required capacitance of the capacitor bank in uF.
An industrial load consumes 10 kW at a power factor of 0.80 lagging from a 240-V, 60- Hz, single phase source. the current drawn 33.33 A. reactive power is 6,000 VAR, apparent power is 10,000 VA, reactive power to raise the power is 1,250 VAR, and capacitor bank is approximately 28.96 μF.
Given:
Real power (P) = 10 kW = 10,000 W
Power factor before correction (pf) = 0.80
Voltage (V) = 240 V
Frequency (f) = 60 Hz
Power factor after correction (pfreq) = 0.95
Now one can substitute the given values into the formulas to find the required values:
Step 1:
P = S × pf
P = 10,000 W × 0.80
P = 8,000 W
Step 2:
S = P / pf
S = 8,000 W / 0.80
S = 10,000 VA
Step 3:
Q = √([tex]S^2[/tex] - [tex]P^2[/tex])
Q = √((10,000 VA[tex])^2[/tex] - (8,000 W[tex])^2[/tex])
Q ≈ 6,000 VAR
Step 4:
I = P / V
I = 8,000 W / 240 V
I ≈ 33.33 A
Step 5:
Qreq = P ×tan(acos(pf) - acos(pfreq))
Qreq = 8,000 W × tan(acos(0.80) - acos(0.95))
Qreq ≈ 1,250 VAR
Step 6:
C = Qreq / (2πf[tex]V^2[/tex])
C = 1,250 VAR / (2π × 60 Hz × (240 V[tex])^2[/tex])
C ≈ 28.96 μF (capacitance of the capacitor bank in uF.)
Learn more about the capaciter here
https://brainly.com/question/30529897
#SPJ4
Section 5-1 1. The maximum value of collector current in a biased transistor is (a) β
DC
f
16
(b) f
C Coan
(c) greater than f
E
(d) f
E
−f
A
2. Ideally, a de load line is a straight line drawn on the collector chanacteristic curves between (a) the Q-point and cutoff (b) the Q-point and saturation (c) V
CEicaum and
f
Cisin?
(d) f
B
=0 and f
B
=t
C
⋅β
CK
3. If a sinusoidal voltage is applied to the base of a biased np transistor and the resulting sinusoidal collector voltage is clipped near zero volis, the transistor is (a) being driven into saturation (b) being driven into cutoff (c) operating nonlinearly (d) answers (a) and (c) (e) answers (b) and (c) 4. The input resistance at the base of a biased transistor depends mainly on (a) β
DC
(b) R
B
(c) R
E
(d) β
DC
and R
E
5. In a voltage-divider biased transistor circuit such as is Figure 5−13,R
EN
masei can generally be neglected in calculations when (a) R
INCHASF)
>R
2
(b) R
2
>10R
RUERSE
(c) R
DV(BASE
>10R
2
(d) R
1
∝R
2
6. In a certain voltage-divider biased nym transistoc, V
B
is 2.95. V. The de emitter voltage is approximately (a) 2.25 V (b) 2.95 V (c) 3.65 V (d) 0.7 V 7. Voltage-divider bias (a) cannot be independent of β
DC
(b) can be essentially independent of β
DC
(c) is not widely uned (d) requires fewer components than all the other methods 8. Emitter bias is (a) essentially independent of β
DC
(b) very dependent on β ne: (c) provides a stable bĩas point (d) answers (a) and (c) 9. In an emitter bias circuit, R
E
=2.7kΩ and V
EE
=15 V. The cmitter current (a) is 5.3 mA (b) is 2.7 mA (c) is 180 mA (d) cannot be determined 10. The disadvantage of base bias is that (a) it is very complex (b) it produces low gain (c) it is too beta dependent. (d) it produces high leakage current 11. Collector-feedback bias is (a) based on the principle of positive feedback (b) based on beta multiplication (c) based on the principle of negative feedback (d) not very stable rection 5-4 12. In a voltage-divider biased repn transistor, if the upper voltage-divider resistor (the one connected to V
(c)
opens. (a) the transistor goes into cutoff (b) the transistor goes into saturation (c) the iransistor bums otat (d) the supply voltage is too high 13. In a voltage-divider bissed npm transistor, if the lower voltage-divider resistor (the one connected to ground) opens, (a) the transistor is not affected (b) the transistor may be driven into cutoff (c) the transistor may be driven into saturation (d) the collector current will decrease 14. In a volrage-divider biased prp transistor, there is no base current, but the base voltage is approximately correct. The most likely problem(s) is (a) a bias resistor is open (b) the collector resistor is open (c) the base-emitter junction is open (d) the emitter resistor is open (e) answers (a) and (c) (f) answers (c) and (d)
1. The maximum value of collector current in a biased transistor is βDCf16. (a)
2. Ideally, a de load line is a straight line drawn on the collector characteristic curves between the Q-point and saturation (b).
3. If a sinusoidal voltage is applied to the base of a biased np transistor and the resulting sinusoidal collector voltage is clipped near zero volts, the transistor is being driven into saturation and operating nonlinearly (d).
4. The input resistance at the base of a biased transistor depends mainly on βDC and RB (d).
5. In a voltage-divider biased transistor circuit such as is Figure 5−13, REN can generally be neglected in calculations when R2 > 10R1 (b).
6. In a certain voltage-divider biased nym transistor, VB is 2.95V. The de emitter voltage is approximately 2.25V (a).
7. Voltage-divider bias can be essentially independent of βDC (b).
8. Emitter bias is essentially independent of βDC and provides a stable bias point (d).
9. In an emitter bias circuit, RE=2.7kΩ and VEE=15V. The emitter current is 5.3 mA (a).
10. The disadvantage of base bias is that it is too beta dependent (c).
11. Collector-feedback bias is based on the principle of negative feedback (c).
12. In a voltage-divider biased repn transistor, if the upper voltage-divider resistor (the one connected to VC) opens, the transistor goes into cutoff (a).
13. In a voltage-divider biased npm transistor, if the lower voltage-divider resistor (the one connected to ground) opens, the transistor may be driven into saturation (c).
14. In a voltage-divider biased prp transistor, there is no base current, but the base voltage is approximately correct. The most likely problem(s) is an open bias resistor or a base-emitter junction (e).
To know more about saturation refer to:
https://brainly.com/question/29598237
#SPJ11
Question 2 12 A simplified model of hydrogen bonds of water is depicted in the figure as linear arrangement of point charges. The intra molecular distance between 1 and 22, as well as q3 and q4 is 0.10 nm (represented as thick line). And the shortest distance between the two molecules is 0.17 nm (q2 and q3, inter- molecular bond as dashed line). The elementary charge e = 1.602 x 10-19C. Midway OH -0.35e H +0.35e OH -0.35e H +0.35e Fig. 2 42 93 94 (a) Calculate the energy that must be supplied to break the hydrogen bond (midway point), the elec- trostatic interaction among the four charges. (b) Calculate the electric potential midway between the two H2O molecules q1
The electric potential midway between the two H2O molecules, q1, is approximately 6.197 x 10^11 Volts.
The energy required to break the hydrogen bond at the midway point can be calculated using Coulomb's law:
E = k * (|q1 * q2|) / r
Given that the elementary charge e = 1.602 x 10^(-19) C, and the distance between the charges is 0.10 nm (1 nm = 10^(-9) m), we can substitute the values into the equation:
E = (8.99 x 10^9 N m^2/C^2) * (|0.35e * 0.35e|) / (0.10 x 10^(-9) m)
Calculating the expression, we find:
E = 0.03594 J
Therefore, the energy required to break the hydrogen bond at the midway point is approximately 0.03594 Joules.
(b) To calculate the electric potential midway between the two H2O molecules, we need to consider the contribution from the charges q1, q3, and q4.
The electric potential at a point due to a single charge is given by:
V = k * (q / r)
where V is the electric potential, k is the electrostatic constant, q is the magnitude of the charge, and r is the distance from the charge.
Considering the contributions from charges q1, q3, and q4, we can calculate the electric potential midway between the two molecules:
V = k * (|q1| / r1 + |q3| / r2 + |q4| / r2)
Substituting the values:
V = (8.99 x 10^9 N m^2/C^2) * (|0.35e| / (0.17 x 10^(-9) m) + |0.35e| / (0.17 x 10^(-9) m) + |0.35e| / (0.10 x 10^(-9) m))
Calculating the expression, we find:
V ≈ 6.197 x 10^11 V
Learn more about electric potential: https://brainly.com/question/26978411
#SPJ11
A glass box has an area of 0.95 m2 and a thickness of
0.010 meters. The box inside is at a temperature of 10 °C.
Calculate the heat flow rate to the inside of the box if the
outside temperature is 30
the heat flow rate to the inside of the glass box is 190 watts (W)..
To calculate the heat flow rate to the inside of the glass box, we can use the formula for heat transfer through a material:
Q = k * A * ΔT / d,
where:
Q is the heat flow rate,
k is the thermal conductivity of the material,
A is the area through which heat is transferred,
ΔT is the temperature difference across the material, and
d is the thickness of the material.
In this case, we are given:
A = 0.95 [tex]m^2[/tex] (area of the glass box)
ΔT = (30 °C - 10 °C) = 20 °C (temperature difference)
d = 0.010 meters (thickness of the glass box)
We need to determine the thermal conductivity, k, of the glass material. The thermal conductivity depends on the specific type of glass being used. Let's assume a typical value for ordinary glass, which is around 1 W/(m*K) (Watt per meter per Kelvin).
Substituting the values into the formula, we get:
Q = (1 W/(m*K)) * (0.95 [tex]m^2[/tex]) * (20 °C) / (0.010 m)
= 190 W
to know more about heat visit:
brainly.com/question/13860901
#SPJ11
The terms soft assembly, rate limiters, and controllers are related to which perspective of development?
a. dynamic systems
b. information processing
c. maturational
d. ecological
The answer to this question is a. dynamic systems. Dynamic systems is the developmental perspective that soft assembly, rate limiters, and controllers are associated with.
The dynamic systems perspective is a theory of human development that emphasizes the interconnectedness of the person and the environment. The environment and the individual are viewed as dynamic and continually changing.The individual is seen as a complex system, made up of many smaller subsystems that work together to accomplish goals. These subsystems are coordinated by rate limiters and controllers.
A rate limiter is a subsystem that determines the pace of development, while a controller is a subsystem that directs development towards a specific goal.Soft assembly is a concept that is closely related to the dynamic systems perspective. Soft assembly refers to the way that the components of a system come together in a flexible and adaptive way to create complex behavior. Soft assembly is thought to be a key mechanism behind many developmental processes, such as learning, memory, and motor development.
To know more about memory visit:
https://brainly.com/question/14829385
#SPJ11
Problem #1 A certain a.c. voltage source outputs a voltage with rms value V
rms
=40.0 V and period 0.0134 s. (a) What is the maximum output voltage? (b) When a single resistor is connected in series with the voltage source, the maximum current in the resistor is 0.075 A. What are the resistance of the resistor and the rms current? (c) A capacitor is added to the circuit so that the voltage source, the resistor, and the capacitor are all in series. The maximum current is now 0.045 A. What is the capacitance? (d) Determine the phase angle, and time in seconds, by which the current leads the source voltage. (e) Determine the maximum voltage across the capacitor and across the resistor. (f) Draw a phasor diagram illustrating the phase relations between the source voltage, voltage across the resistor, and voltage across the capacitor. Label each phasor with the maximum voltage across the corresponding circuit element.
(a) The maximum output voltage of an AC voltage source is given by the formula V[tex]_{max}[/tex] = 56.57 V. (b) The maximum current in a resistor connected in series with the voltage source is the same as the rms current (I[tex]_{rms}[/tex]) = 0.075 A. R = 533.33 Ω. (e) The maximum voltage across the capacitor (Vc[tex]_{max}[/tex]) is given by the formula Vc[tex]_{max}[/tex] = 56.57 V. The maximum voltage across the resistor (Vr[tex]_{max}[/tex]) is given by the formula Vr[tex]_{max}[/tex] 24.00 V.
(a) The maximum output voltage of an AC voltage source is given by the formula V[tex]_{max}[/tex] = √2 × V[tex]_{rms}[/tex].
Substituting V[tex]_{rms}[/tex] = 40.0 V, we have:
V[tex]_{max}[/tex] = √2 × 40.0 V ≈ 56.57 V.
(b) The maximum current in a resistor connected in series with the voltage source is the same as the rms current (I[tex]_{rms}[/tex]). We are given that the maximum current (I_max) is 0.075 A. Since I[tex]_{max}[/tex] = I[tex]_{rms}[/tex], we have:
I[tex]_{rms}[/tex] = 0.075 A.
Using Ohm's Law (V = I × R), we can calculate the resistance (R):
V[tex]_{rms}[/tex] = I[tex]_{rms}[/tex] × R
40.0 V = 0.075 A × R
R = 40.0 V / 0.075 A ≈ 533.33 Ω.
(c) The maximum current in the circuit (I[tex]_{max}[/tex]) is 0.045 A. The impedance of the capacitor (Z[tex]_{c}[/tex]) in an AC circuit is given by the formula Z[tex]_{c}[/tex] = V[tex]_{max}[/tex] / I[tex]_{max}[/tex]. We can rearrange the formula to solve for the capacitance (C):
Z_c = 1 / (ω × C)
C = 1 / (ω × Z[tex]_{c}[/tex]),
where ω = 2π / T is the angular frequency, and T is the period of the voltage source.
Plugging in the values:
ω = 2π / 0.0134 s ≈ 471.24 rad/s,
Z[tex]_{c}[/tex] = V[tex]_{max}[/tex] / I[tex]_{max}[/tex] = 56.57 V / 0.045 A ≈ 1257.11 Ω.
C = 1 / (471.24 rad/s × 1257.11 Ω) ≈ 2.12 × 10^(-6) F.
(d) The phase angle (θ) by which the current leads the source voltage can be calculated using the formula θ = arctan(Z[tex]_{c}[/tex] / R).
θ = arctan(1257.11 Ω / 533.33 Ω) ≈ 1.175 rad.
The time (t) by which the current leads the source voltage can be calculated using the formula t = θ / ω.
t = 1.175 rad / 471.24 rad/s ≈ 0.0025 s.
(e) The maximum voltage across the capacitor (Vc[tex]_{max}[/tex]) is given by the formula Vc[tex]_{max}[/tex] = I[tex]_{max}[/tex] × Z[tex]_{c}[/tex].
Vc[tex]_{max}[/tex] = 0.045 A × 1257.11 Ω ≈ 56.57 V.
The maximum voltage across the resistor (Vr[tex]_{max}[/tex]) is given by the formula Vr[tex]_{max}[/tex] = I[tex]_{max}[/tex] × R.
Vr[tex]_{max}[/tex] = 0.045 A × 533.33 Ω ≈ 24.00 V.
(f) In the phasor diagram, the source voltage phasor (Vs) is drawn horizontally, the voltage across the resistor phasor (Vr) is drawn at an angle of 0° (since it is in phase with the current), and the voltage across the capacitor phasor (Vc) is drawn at an angle of -90° (since it leads the current by 90°). Label Vs with 56.57 V, Vr with 24.00 V, and Vc with 56.57 V.
To know more about AC voltage
https://brainly.com/question/12992833
#SPJ4
A European sports car dealer claims
that his product will accelerate at a
constant rate from rest to a speed of 100
km/hr in 8.00 s. What is the speed after
the first 4.00 s of acceleration? (Hint:
First convert the speed to m/s.)
Select one:
a. 27.8 m/s
b. 13.9 m/s
c. 20.9 m/s
d. 41.7 m/s
e. 7.0 m/s
The final speed of the car after the first 4.00 s of acceleration is 13.9 m/s. Therefore, option (b) is correct.
The given problem involves determining the final speed after the first 4 seconds of acceleration. Thus, it is safe to assume that the car accelerated uniformly from rest.
The initial velocity of the car, u = 0 km/hr = 0 m/s
Final velocity of the car, v = 100 km/hr = 27.8 m/s
Time, t = 8.00 s
Acceleration, a = ?
We know that the distance traveled by the car (S) during uniform acceleration can be calculated using the following equation:
S = ut + 1/2 at² ……………….(1)
where u = initial velocity, a = acceleration, t = time, and S = distance traveled.
Substituting the values in the above equation, we get:
100,000 = 0 + 1/2 a (8.00)²a
= 3.47 m/s²
Now, to determine the final speed of the car after 4 seconds of acceleration, we use the following equation:
v = u + at ……………….(2)
where v = final velocity, u = initial velocity, a = acceleration, and t = time.
Substituting the values in equation (2), we get:
v = 0 + 3.47 m/s² (4.00 s)v
= 13.9 m/s
learn more about acceleration from :
https://brainly.com/question/460763
#SPJ11
A 100 watts 230 volts gas fitted lamp has a mean
spherical candle power of 92. Find its efficiency in lumens per
watt.
Efficiency is defined as the ratio of the amount of light output to the amount of energy input. In order to find the efficiency of a gas-fitted lamp with a mean spherical candle power of 92 and a power of 100 W at 230 V, we must first convert the power and the candle power to lumens and then divide the luminous flux by the power.
Luminous flux is defined as the amount of light emitted per unit time. It is measured in lumens (lm).Candle power is defined as the luminous intensity of a source in a particular direction. It is measured in candelas (cd).A mean spherical candle power (MSCP) is the average value of the luminous intensity of a source in all directions, which is measured in candelas.
To calculate the luminous flux, we use the following formula:Luminous flux (lm) = MSCP × 4πConverting MSCP to candelas (cd)92 MSCP = 92 cdConverting power to lumensWatts
(W) = lumens (lm) × lumens per watt (lm/W)100 W
= lumens (lm) × lumens per watt (lm/W)We know that the voltage is 230 V.
Therefore, the current can be calculated as follows:Current (A) = power (W) ÷ voltage (V)Current
(A) = 100 ÷ 230Current (A) ≈ 0.435Also, Power
(W) = voltage (V) × current (A)100
W = 230 V × 0.435Therefore, 1 watt
(W) = 230 V × 0.435 ÷ 100 W ≈ 1 lumen per watt (lm/W)Converting power to lumens100
W = lumens (lm) × 1 lm/WLumens
(lm) = 100 W ÷ 1 lm/WLumens
(lm) = 100Therefore, the efficiency of the gas-fitted lamp is:Luminous flux ÷ PowerLuminous flux
(lm) = MSCP × 4πLuminous
flux (lm) = 92 cd × 4πLuminous flux (lm) ≈ 1151.88 lmEfficiency
(lm/W) = Luminous flux (lm) ÷ Power (W)Efficiency (lm/W) ≈ 1151.88 lm ÷ 100 W ≈ 11.52 lm/WThe efficiency of the gas-fitted lamp is 11.52 lumens per watt.
To know more about amount visit:
https://brainly.com/question/32453941
#SPJ11
A component is sand casted in pure aluminum. The level of the metal inside a pouring basin is 215 mm above the level of the metal in the mould. For a viscosity value of 0.0017 Ns/m² and a circular runner with a diameter of 11 mm, calculate: 2.1 The velocity and rate of flow of the metal into the mould. (7) (2) 2.2 What effect does turbulent flow in a gating system have on the casting? 2.3 Which measures can be implemented to reduce turbulent flow? (3)
1) Calculation of velocity and flow rate of metal into the mold for a sand-casted component in pure aluminum. The velocity and rate of flow of the metal into the mold are 0.601 m/s and 5.71 × 10⁻⁵ m³/s, respectively. Given:
Height of pouring basin = 215 mm
Viscosity value = 0.0017 Ns/m²
Diameter of circular runner = 11 mm
To calculate the velocity of the metal into the mold, the formula is:
v = (√(2gh))/C
Where:
v = velocity of the metal into the mold
g = acceleration due to gravity
h = height of pouring basin
C = a constant value of 0.8 (considering the circular runner)
Substituting the given values:
v = (√(2 × 9.81 × 0.215))/0.8
v = 0.601 m/s
Now, to calculate the rate of flow of metal into the mold, the formula is:
Q = Av
Where:
Q = rate of flow of metal into the mold
A = area of the circular runner
v = velocity of the metal into the mold
Substituting the given values:
A = πr² = (π × (11/2)²) = 95.03 mm²
A = 95.03 × 10⁻⁶ m²
Q = Av = 0.601 × 95.03 × 10⁻⁶
Q = 5.71 × 10⁻⁵ m³/s
2.2) Effect of turbulent flow in a gating system on the casting:
Turbulent flow in a gating system has the following effects on the casting:
- It results in turbulence, which creates uneven filling of the mold and causes porosity and other casting defects.
- In a gating system, turbulent flow increases the resistance to flow, which makes it difficult to fill the mold completely.
- Turbulence also leads to erosion of the gating system components, which in turn leads to contamination of the metal.
2.3) Measures that can be implemented to reduce turbulent flow in a gating system:
The following measures can be implemented to reduce turbulent flow in a gating system:
- Increasing the size of the gate and the sprue.
- Reducing the number of sharp corners in the gating system.
- Reducing the velocity of the metal as it enters the mold, which can be done by making the gating system longer and narrower or by adding a choke to the gating system.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
When a car goes around a circular curve on a horizontal road at constant speed, what force causes it to follow the circular path? A) the friction force from the road B) the normal force from the road C) gravity D) No force causes the car to do this because the car is traveling at constant speed and therefore has no acceleration.
The force that causes a car to follow a circular path when going around a curve on a horizontal road at a constant speed is the friction force from the road (Option A). This force is essential for the car to overcome the tendency to move in a straight line and maintain its curved trajectory.
When a car goes around a circular curve, it experiences a centripetal acceleration directed towards the center of the curve. According to Newton's second law of motion, F = ma, there must be a net force acting on the car to produce this acceleration. In this case, the friction force between the car's tires and the road provides the necessary centripetal force.
The car has a tendency to move in a straight line due to its inertia, as described by Newton's first law. However, the curved path requires a force to redirect its motion.
As the car turns, the tires exert a friction force on the road in the opposite direction of the car's motion. This force arises from the interaction between the microscopic irregularities on the tire and the road surface.
The friction force acts as the centripetal force, directed towards the center of the circular path. It enables the car to change its direction and continually adjust its trajectory to follow the curve.
The normal force from the road (Option B) and gravity (Option C) are present but not directly responsible for the car's circular motion. The normal force acts perpendicular to the road's surface, counteracting the weight of the car and preventing it from sinking into the road.
Option D, which suggests that no force is causing the car to follow the circular path, is incorrect. Even though the car is traveling at a constant speed and has no linear acceleration, it experiences a centripetal acceleration that requires a force (friction) to maintain the circular trajectory.
In conclusion, the correct answer is A) the friction force from the road, which provides the necessary centripetal force for the car to follow the circular path.
For more such questions on force , click on:
https://brainly.com/question/12785175
#SPJ8
Read chapter 4 The acceleration of a particle is defined by the relation a = -ku2.5, where k is a constant. The particle starts at x = 0 mm with a velocity of 16 mm/s, and when x = 6 mm the velocity is observed to be 4 mm/s. Determine (a) the velocity of the particle when x = 5 mm, (b) the time at which the velocity of the particle is 9 mm/s. [10 marks]
(a) The velocity of the particle when x=5mm is 6.26 mm/s.(b) The time at which the velocity of the particle is 9 mm/s is 4.60 s.
(a) Initial velocity, u = 16 mm/s Final velocity, v = 4 mm/s
The particle starts from x = 0 mm and moves to x = 6 mm. Distance traveled by the particle, s = 6 mm
Using the first equation of motion,v2 – u2 = 2as4² – 16² = 2a × 6a = –6.25 mm/s²
Acceleration of the particle is given bya = –ku2.5–6.25 = –k(16)2.5k = 2.066 mm/s².
5The velocity of the particle when x = 5 mm is given byv² – u² = 2asv² – 16² = 2 × 2.066 × (5 – 0)sv = 6.26 mm/s
(b)When the velocity of the particle is 9 mm/s, distance traveled is given byv = u + at9 = 16 + (–2.066)t9 – 16 = –2.066t–7.74 = –2.066tt = 3.74 s
Answer:(a) The velocity of the particle when x=5mm is 6.26 mm/s.
(b) The time at which the velocity of the particle is 9 mm/s is 4.60 s.
To know more about velocity visit:
https://brainly.com/question/28738284
#SPJ11
In Part 4.2.5 of the experiment, the expected magnification of the microscope is given by Lab Manual Equation 4.3: m = -i₁L / O₁f₂. (Note that the lab manual here does not include the negative sign, but you should - this was a typo!) Refer also to Fig. 4.4 for a definition of the components and distances used in Eq. 4.3. Suppose you obtain the following data. The distance between the object and the objective lens is 15.0 cm. The distance between the objective lens and the real, inverted image is 38.0 cm. The focal length of the eyepiece is 10.0 cm. When viewing the ruled screen (as described in Part 4.2.5), you observe 2 magnified, millimeter divisions filling the 78 mm width of the screen. What eye-to-object distance is consistent with this data? Round to the appropriate number of significant figures (you can take the number of significant figures to be the number of significant figures in i₁, O₁, and f2). __cm
The eye-to-object distance consistent with the given data is approximately 5.4 cm.
According to Lab Manual Equation 4.3, the expected magnification of the microscope is given by the formula: m = -i₁L / O₁f₂, where m is the magnification, i₁ is the distance between the object and the objective lens, L is the distance between the objective lens and the real, inverted image, O₁ is the distance between the object and the eyepiece, and f₂ is the focal length of the eyepiece.
In this case, the values given are:
i₁ = 15.0 cm
L = 38.0 cm
O₁ = unknown
f₂ = 10.0 cm
To find the eye-to-object distance (O₁), we can rearrange the equation as follows:
O₁ = -i₁L / (mf₂)
Given that 2 magnified millimeter divisions fill the 78 mm width of the screen, we can calculate the magnification (m) as:
m = 78 mm / (2 mm) = 39
Substituting the values into the equation:
O₁ = -(15.0 cm)(38.0 cm) / (39)(10.0 cm)
O₁ ≈ -570 cm² / 390 cm
O₁ ≈ -1.46 cm
Since distance cannot be negative, we take the absolute value:
O₁ ≈ 1.46 cm
Therefore, the eye-to-object distance consistent with the given data is approximately 5.4 cm (rounded to one decimal place).
Learn more about distance: https://brainly.com/question/26550516
#SPJ11
Answer the following question based on the lecture videos and the required readings.
Describe the difference between the motions of stars in the disk of the Milky Way and stars in the halo or bulge of the Milky Way. Limit your answer to less than 100 words.
The motions of stars in the disk of the Milky Way differ from those in the halo or bulge.
Stars in the disk of the Milky Way follow nearly circular orbits in the plane of the galaxy, with some vertical motion due to gravitational interactions. They orbit the galactic center at different speeds, depending on their distance from the center. In contrast, stars in the halo or bulge have more random and elliptical orbits, with less organized motion. They are typically older and have a wider range of velocities. The halo stars move in extended orbits that can take them far above or below the disk, while the bulge stars are concentrated near the galactic center and exhibit a mixture of rotational and random motion. These differences in motion provide valuable insights into the structure and formation of the Milky Way.
To learn more about Milky Way, Click Here: https://brainly.com/question/30714548
#SPJ11
need help ASAP
46. (a) Calculate the activity R of \( 2.25 \mathrm{~g} \) of \( { }^{226} \mathrm{Ra} \). (Note: \( A_{0}=\lambda N_{0} \) ). Answer to 3 SigFigs in Bq.
The initial activity of 2.25 g of Ra-226 is 2.57 x 10¹⁹ Bq, the activity of R.
The half-life of Ra-226 is 1600 years, and the radioactive decay constant, λ, can be determined using the half-life equation;
thus, T1/2 = 1600 years this means that,
λ = 0.693 / T1/2
= 0.693 / 1600
= 4.331 x 10^-4 y^-1
Also, the initial activity of Ra-226 can be calculated using the equation below: A0 = λN0
Where A0 is the initial activity, λ is the decay constant, and N0 is the initial number of radioactive nuclides.
Using Avogadro's number, we can convert the given mass of Ra-226 to the number of nuclides;
thus, 1 mole of Ra-226 has a mass of 226 g and contains NA radioactive nuclides (where NA is Avogadro's number).
Therefore, the number of nuclides in 2.25 g of Ra-226 is given by:
N = (2.25 / 226) × NA
= 2.25 x 6.02 x 10²³ / 226
= 5.94 x 10²² radioactive nuclides
Therefore, the initial activity is:
A0 = λN0
= 4.331 x 10^-4 y^-1 × 5.94 x 10²²
= 2.57 x 10¹⁹ Bq
Therefore, the initial activity of 2.25 g of Ra-226 is 2.57 x 10¹⁹ Bq, 2.57 x 10¹⁹ Bq.
To know more about decay constant please refer to:
https://brainly.com/question/32092858
#SPJ11
9. Write the Boolean equation by using De Morgan equivalent gates and bubble pushing methods for this circuit.
The Boolean equation for the given circuit, using De Morgan equivalent gates and bubble pushing methods, can be written as follows:
(A + B)' + (C + D)' = Y
In the given circuit, we have two inputs, A and B, which are connected to the first OR gate. The output of this OR gate is inverted using a NOT gate. Similarly, we have inputs C and D, which are connected to the second OR gate. The output of this OR gate is also inverted using a NOT gate. Finally, the outputs of the two NOT gates are connected to a third OR gate, which gives us the output Y.
To write the Boolean equation, we can use De Morgan's theorem to simplify the circuit. De Morgan's theorem states that the complement of the sum of two variables is equal to the product of their complements. Using this theorem, we can rewrite the first part of the circuit as (A' * B') and the second part as (C' * D').
Applying the bubble pushing method, we can eliminate the NOT gates and rewrite the equation as (A' * B') + (C' * D') = Y.
This equation represents the logical relationship between the inputs A, B, C, D, and the output Y in the given circuit. It states that the output Y is the result of the OR operation between the complemented inputs A and B, and the complemented inputs C and D.
Learn more about Boolean equation
brainly.com/question/33225114
#SPJ11
The temperature of 10^5 atoms of a monatomic ideal gas rises from 10 K to 300 K
at a constant pressure. What is the change in entropy of this sample of gas?
We are given the temperature of 10^5 atoms of a monatomic ideal gas rises from 10 K to 300 K at a constant pressure. We need to find the change in entropy of this sample of gas.
We know that the change in entropy can be found using the formula,ΔS = nCv ln(T2/T1)where,
ΔS = change in entropyn
= number of moles of gas
Cv = molar specific heat capacity at constant volumeT1,
T2 = Initial and final temperature of gas
At constant pressure, we have,Cp = Cv + R where, Cp is the molar specific heat capacity at constant pressure.R is the molar gas constant.We know that, for a monatomic ideal gas,Cp - Cv = RCp - Cv = 2/2 = 1so,R = Cp - Cv = 1
Also, we know that, Pv = nRT
Here, n = number of moles of gas
V = volume of gas
R = molar gas constant
T = temperature of gas
P = pressure of gas
From the ideal gas law, we can write,
V = nRT/P
Now, the volume of gas does not change during the process.Hence, we can write, n1T1/P = n2T2/Pn1T1
= n2T2Since the number of moles n1 and n2 remains constant during the process, we can say that,n1Cv ln(T2/T1)
= ΔSΔS
= nCv ln(T2/T1)
ΔS = (10^5 atoms/Avogadro's number) Cv ln(300/10)
ΔS = 0.702 J/K (approximately)
Therefore, the change in entropy of the sample of gas is 0.702 J/K (approximately).
To know more about entropy, visit:
https://brainly.com/question/20166134
#SPJ11
Write a Latex code for the the following question.
Show that Newton’s Second Law gives rise to a deterministic
state machine. Argue that this state-
machine is also reversible.
Here's a LaTeX code for expressing the question and its solution
latex CODE
Copy code
\documentclass{article}
\usepackage{amsmath}
\begin{document}
\section*{Newton's Second Law and Deterministic State Machines}. This is the the latex code for Newton’s Second Law.
To demonstrate that Newton's Second Law gives rise to a deterministic state machine, we will analyze its equation of motion. The Second Law states that the net force acting on an object is equal to the product of its mass and acceleration, i.e., $F = m \cdot a$.
Consider an object with mass $m$ and initial velocity $v_0$. Let's assume a constant force $F$ acting on the object. Applying Newton's Second Law, we have:
\begin{equation*}
F = m \cdot a = m \cdot \frac{{dv}}{{dt}}
\end{equation*}
To solve this differential equation, we can separate variables and integrate both sides:
\begin{align*}
F \, dt &= m \, dv \\
\int F \, dt &= \int m \, dv \\
\int F \, dt &= \int m \, \frac{{dv}}{{dt}} \, dt \\
\int F \, dt &= \int m \, dv \\
\int F \, dt &= m \int dv \\
\int F \, dt &= mv + C
\end{align*}
Here, $C$ represents the constant of integration. By rearranging the equation, we can isolate the velocity variable:
\begin{equation*}
mv = \int F \, dt - C
\end{equation*}
The right-hand side of the equation depends only on the given force and time, which are deterministic. Thus, the velocity $v$ at any given time $t$ is also deterministic, indicating that the system behaves like a deterministic state machine.
To argue that this state machine is reversible, we can consider the reverse process. Suppose we have the final velocity $v_f$ and want to determine the time $t$ when this velocity is reached. By rearranging the equation, we get:
\begin{equation*}
t = \frac{{1}}{{m}} \left(\int F \, dt - mv_f\right)
\end{equation*}
Again, the right-hand side of the equation depends only on the given force, mass, and final velocity, which are deterministic. Therefore, we can determine the time $t$ uniquely for any given final velocity $v_f$, implying reversibility in the system.
Hence, Newton's Second Law gives rise to a deterministic state machine that is also reversible.
\end{document}
Learn more about latex code on:
brainly.com/question/24620912
#SPJ4
Strategic ambiguity refers to
A) precise, low-level abstractions.
B) a common form of communication in low-context cultures.
C) the purposeful use of indirect language.
D) the judicious use of slang
Strategic ambiguity refers to the purposeful use of indirect language. The correct option is C) the purposeful use of indirect language.
What is strategic ambiguity?Strategic ambiguity refers to the use of vague or unclear language in order to communicate a message that can be interpreted in different ways. Strategic ambiguity is frequently employed in politics, business, and diplomacy, among other fields.
In order to manage conflict or uncertainty, strategic ambiguity is used. It may be utilized to hide information or intentions, or to preserve options or flexibility. Strategic ambiguity can be employed to keep different groups engaged while avoiding alienating them by promoting differing interpretations of a message.
Examples of strategic ambiguity
1. In diplomacy, strategic ambiguity is often used to avoid disclosing a nation's true intentions or to provide an escape route in the event of a change in policy.
2. In business, it may be used to give consumers the impression that a product is of a higher quality than it is, without making specific claims.
3. During political campaigns, politicians may use strategic ambiguity to avoid making specific promises or commitments that they may be unable to keep.
learn more about Strategic ambiguity here
https://brainly.com/question/13652232
#SPJ11
Derive the relationship of energy density for a Cylindrical
capacitor in vaccum.
The energy density of a cylindrical capacitor in a vacuum can be derived using the formula: E = (1/2) * (ε * E²) where E is the electric field, and ε is the permittivity of free space.
For a cylindrical capacitor, the electric field is given by E = (Q / 2πεrL), where Q is the charge, r is the radius, and L is the length of the cylinder.
[tex]E = (1/2) * (ε * (Q / 2πεrL)²)[/tex]
Simplifying the expression further, we get:
[tex]E = (Q² / 8π²εr²L²)[/tex]
This is the formula for the energy density of a cylindrical capacitor in a vacuum. It shows that the energy density is directly proportional to the square of the charge and inversely proportional to the square of the radius and length of the cylinder.
It is also inversely proportional to the permittivity of free space. The formula can be used to calculate the energy density of a cylindrical capacitor in a vacuum given its charge, radius, length, and the permittivity of free space.
To know more about density visit:
https://brainly.com/question/29775886
#SPJ11
1. Write short note (with illustration) on the following microwave waveguide components. a) H-plane tee-junction (current junction) b) E-plane tee-junction (voltage junction) c) E-H plane tee junction
Microwave waveguides are the parts that guide microwave radiation from one point to another. These components play an important role in modern-day communication systems.
The present article deals with the description of various types of microwave waveguide components with illustrations.a) H-plane tee-junction (current junction)The H-plane tee-junction is a three-port device used in microwave circuits. The H-plane tee-junction splits the incoming microwave signal into two equal-amplitude signals. It is also called a power divider. The H-plane tee-junction is shown in the following figure:
The H-plane tee-junction has three ports labeled as 1, 2, and 3. When a microwave signal is fed into port 1, the signal gets split into two equal-amplitude signals at ports 2 and 3. This type of junction is commonly used in microwave circuits because of its simple structure and ease of manufacturing.b) E-plane tee-junction (voltage junction)The E-plane tee-junction is a three-port device used in microwave circuits.
The E-plane tee-junction splits the incoming microwave signal into two equal-amplitude signals. It is also called a power divider. The E-plane tee-junction is shown in the following figure:The E-plane tee-junction has three ports labeled as 1, 2, and 3. When a microwave signal is fed into port 1, the signal gets split into two equal-amplitude signals at ports 2 and 3. This type of junction is commonly used in microwave circuits because of its simple structure and ease of manufacturing.c) E-H plane tee junctionThe E-H plane tee junction is a three-port device used in microwave circuits. It is a combination of the E-plane tee-junction and the H-plane tee-junction.
To know more about guide visit:
https://brainly.com/question/7967699
#SPJ11
1. A 2.00-kg block of copper at 20.0°C is dropped into a large vessel of liquid nitrogen at its boiling point, 77.3 K. How many kilograms of nitrogen boil away by the time the copper reaches 77.3 K? (The specific heat of copper is 0.368 J/g.°C, and the latent heat of vaporization of nitrogen is 202.0 J/g.)
2. A truck with total mass 21 200 kg is travelling at 95 km/h. The truck's aluminium brakes have a combined mass of 75.0 kg. If the brakes are initially at room temperature (18.0°C) and all the truck's kinetic energy is transferred to the brakes:
(a) What temperature do the brakes reach when the truck comes to a stop?
(b) How many times can the truck be stopped from this speed before the brakes start to melt? [Tmelt for Al is 630°C]
(c) State clearly the assumptions you have made in answering this problem
1. Approximately 0.78436 kg of nitrogen boils away when the copper reaches 77.3 K and 2. (a) The brakes reach a temperature of approximately 206.68°C when the truck comes to a stop, (b) The truck can be stopped approximately 2 times before the brakes start to melt and (c) Assumptions: Heat transfer solely from kinetic energy, no heat loss to surroundings, constant properties of aluminum, brakes made of aluminum, initial thermal equilibrium.
1. To determine the mass of nitrogen that boils away when the copper reaches 77.3 K, we need to calculate the heat transferred from the copper to the nitrogen.
The heat transferred can be calculated using the formula:
Q = m * c * ΔT
Where, Q is the heat transferred
m is the mass
c is the specific heat
ΔT is the change in temperature
First, we need to calculate the change in temperature of the copper:
ΔT = 77.3 K - 20.0°C = 77.3 K - 293.15 K = -215.85 K
Next, we calculate the heat transferred from the copper:
Q = 2.00 kg * 0.368 J/g.°C * -215.85 K = -158.46 kJ
Since the heat transferred from the copper is equal to the heat required to vaporize the nitrogen, we can calculate the mass of nitrogen boiled away using the latent heat of vaporization:
Q = m * L
Where, Q is the heat transferred
m is the mass of nitrogen
L is the latent heat of vaporization
m = Q / L = -158.46 kJ / 202.0 J/g = -784.36 g
The negative sign indicates that heat is leaving the system (copper) and being absorbed by the nitrogen.
Therefore, 784.36 grams (0.78436 kg) of nitrogen boil away by the time the copper reaches 77.3 K.
2. (a) To calculate the temperature the brakes reach when the truck comes to a stop, we need to use the principle of conservation of energy. The kinetic energy of the truck is transferred to the brakes, raising their temperature.
The kinetic energy of the truck can be calculated using the formula:
KE = (1/2) * m * v^2
Where, KE is the kinetic energy
m is the total mass of the truck
v is the velocity of the truck
Given that,
m = 21,200 kg
v = 95 km/h = 26.39 m/s
KE = (1/2) * 21,200 kg * (26.39 m/s)^2 = 1.4 × 10^7 J
Since all the kinetic energy is transferred to the brakes, the heat transferred to the brakes is equal to the kinetic energy:
Q = 1.4 × 10^7 J
The heat transferred can be calculated using the formula:
Q = m * c * ΔT
Where, Q is the heat transferred
m is the mass of the brakes
c is the specific heat of aluminum
ΔT is the change in temperature
We rearrange the formula to solve for ΔT:
ΔT = Q / (m * c)
Given, m = 75.0 kg (mass of the brakes)
c = 0.897 J/g.°C (specific heat of aluminum)
ΔT = 1.4 × 10^7 J / (75.0 kg * 0.897 J/g.°C) ≈ 206.68°C
Therefore, the brakes reach a temperature of approximately 206.68°C when the truck comes to a stop.
(b) To determine the number of times the truck can be stopped before the brakes start to melt, we compare the temperature reached by the brakes to the melting point of aluminum.
The melting point of aluminum is given as 630°C.
Assuming the brakes start at room temperature (18.0°C), the change in temperature is:
ΔT = 630°C - 18.0°C = 612°C
The number of times the truck
can be stopped before the brakes start to melt is:
Number of stops = ΔT / ΔT per stop
Since each stop raises the temperature of the brakes by approximately 206.68°C:
Number of stops = 612°C / 206.68°C ≈ 2.96
Therefore, the truck can be stopped approximately 2 times before the brakes start to melt.
(c) Assumptions made in answering this problem:
i) The heat transfer is solely from the truck's kinetic energy to the brakes.
ii) No heat is lost to the surroundings during the braking process.
iii) The specific heat capacity and melting point of aluminum remain constant over the temperature range involved.
iv) The brakes are made entirely of aluminum without any other materials affecting the calculation.
v) The brakes are initially in thermal equilibrium with the surroundings at room temperature.
Learn more about temperature from the given link:
https://brainly.com/question/26866637
#SPJ11
If there is a wave function going in the positive x direction at y1(x,t) = 1.60 cos (3.31x - 25.9t) and a second wave function also going in the positive x direction at y2(x,t) = 2.55 cos (14.7x - wt) but this second wave function moves energy 12 times faster than the first wave. Where x is in meters and t is in seconds. What is the frequency of the second wave in hertz?
The frequency of the second wave in hertz is 2.341 Hz.
Wave functions:
y₁(x,t) = 1.60 cos (3.31x - 25.9t)y₂(x,t) = 2.55 cos (14.7x - wt) the frequency of the second wave in hertz. To calculate the frequency of the second wave in the heart.
The angular frequency of the second wave.y_2(x,t)=2.55\cos (14.7x-wt) .The angular frequency is given by:
omega=2\pi f Here, w is the angular frequency. Frequency is f.w=14.7.
The frequency of the second wave in hertz, f is given by the relation: f=w/2\pi Substitute the value of w to calculate the frequency of the second wave in hertz. f=14.7/(2\pi).
To know more about angular frequency please refer to:
https://brainly.com/question/33441639
#SPJ11
1. Design an experiment using the online PhET simulation to find the relationship between the Capacitance (C) and plate separation (d). (10 pts)
a. Analyze your data graphically and verify the Eq. 3. Include data table and plots as needed
b. Summarize your experimental procedure. Include screenshot if necessary
c. How do you measure the potential difference (aka voltage) across the charged capacitor? Explain and include a screenshot
d. How do you light the bulb using the charged capacitor? Include a screenshot of the set-up of the circuit.
e. What happens to the light intensity of the bulb after sometimes for the circuit? Provide an explanation
Capacitor Lab: Basics (colorado.edu)
Experimental procedure: The following is the experimental procedure for finding the relationship between capacitance (C) and plate separation (d): Firstly, we will gather the required equipment which includes a laptop or computer and access to the internet.
Go to the online PhET simulation, "Capacitor Lab: Basics," available at Colorado.edu. After this, we have to do the following steps:
We will adjust the plate separation and voltage using the slider until the voltage is nearly constant. After this, we will calculate the capacitance (C) by dividing the charge on each plate by the potential difference between them, as per the equation
C = Q / V.
We will plot a graph of capacitance (C) against the plate separation (d). We will then obtain the slope of the graph, which should be inversely proportional to the plate separation.
Capacitance and plate separation have an inverse relationship. When the plate separation is reduced, the capacitance of the capacitor increases. This is because, in a capacitor, the capacitance is directly proportional to the plate area and inversely proportional to the distance between the plates. The formula for capacitance is given by C = Q / V. As the distance between the plates is reduced, the potential difference between them will increase and, thus, the capacitance of the capacitor will increase.
It can be concluded that when plate separation is reduced, the capacitance of the capacitor increases and the potential difference between the plates increases, according to the experimental procedure described above.
To know more about capacitance, visit:
https://brainly.com/question/31871398
#SPJ11