Pre-charge circuits typically shut off pre-charge mode when the circuit voltage reaches 90% or 95% of the operating voltage. When pre-charging is finished, the pre-charge resistance is disconnected from the power supply circuit and switched back to a low-impedance power source for normal mode.
A current-limiting circuit known as pre-charge reduces the charging rate of the bus capacitors during power-up in a pulse width modulated (or PWM) VFD. (For more information on bus capacitors, go HERE) The input power devices would be harmed otherwise by the early inrush. To control this inrush current and gradually charge the downstream capacitance, a precharge circuit is employed. For components to function properly and be protected in high-voltage applications, it is essential.
Learn more about voltage
https://brainly.com/question/2526786
#SPJ4
Water is pumped from ground level to a reservoir of a roof of a building 15m high.The reservoir holds 12cm2 of water and it takes 40minutes to fill it by the pump, calculate the power of the pump assuming it's efficiency is 65%.
(Density of water=1000kg/M3 and g=10ms-2)
Answer:
The power of the pump can be calculated using the following equation: Power = (Volume of water * Density of water * gravity * height) / (Time * Efficiency)
Therefore, the power of the pump is (12 * 1000 * 10 * 15) / (40 * 0.65) = 18,750 Watts.
give me brainiest
for the following unbalanced reaction, suppose exactly 6.95 g of each reactant is taken. determine which reactant is limiting, and also determine what mass of the excess reagent will remain after the limiting reactant is consumed.
Suppose exactly 6.95 g of each reactant is taken and the following details are given by A and B then 6.95 g of A is equivalent to 6.95/molar mass of A moles of A. 6.95 g of B is equivalent to 6.95/molar mass of B moles of B.
How much extra reagent will still be present once the limiting reactant has been used up?To determine which reactant is limiting, we need to compare the amount of each reactant to the stoichiometry of the reaction.
The stoichiometry of the reaction is 1:2 for reactants A and B, respectively.
Therefore, if we have 6.95 g of A and 6.95 g of B, we can calculate the ratio of A to B to determine which reactant is limiting.
6.95 g of A is equivalent to 6.95/molar mass of A moles of A.
6.95 g of B is equivalent to 6.95/molar mass of B moles of B.
Comparing the moles of A and moles of B, we can see that A is limiting, as there is less A than required by the stoichiometry of the reaction.
To determine the mass of the excess reagent (B) that will remain after the limiting reactant (A) is consumed, we need to calculate the moles of B that are in excess.
We can calculate the moles of B that are used up by the reaction (based on the stoichiometry of the reaction) and subtract this from the total moles of B that were initially present.
The remaining moles of B can then be converted back into grams to find the mass of B that will remain.
Using the above method, the mass of the B remaining after A is consumed can be calculated.
To learn more about stoichiometry refer:
https://brainly.com/question/30215297
#SPJ4
In Fig. 22−35 the four particles form a square of edge length a=5.00 cm and have charges q 1 =+10.0 nC,q 2 =−20.0 nC,q 3 =+20.0 nC, and q 4 =−10.0 nC, In unit vector notation, what net electric field do not particles produce at the square's center?
Net electric field produced by the four particles at the square's center is zero.
What is electric field?The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them is called an electric field.
Electric field produced by each particle at the center of the square can be calculated as:
E1 = k * q1 / (5/sqrt(2))^2 = 810^9 N/C * (1010^-9 C) / (5/sqrt(2))^2 = 410^9 N/C
E2 = k * q2 / (5/sqrt(2))^2 = 810^9 N/C * (-2010^-9 C) / (5/sqrt(2))^2 = -810^9 N/C
E3 = k * q3 / (5/sqrt(2))^2 = 810^9 N/C * (2010^-9 C) / (5/sqrt(2))^2 = 810^9 N/C
E4 = k * q4 / (5/sqrt(2))^2 = 810^9 N/C * (-1010^-9 C) / (5/sqrt(2))^2 = -410^9 N/C
So, E net = E1 + E2 + E3 + E4 = 410^9 N/C + (-810^9 N/C) + 810^9 N/C + (-410^9 N/C) = 0 N/C
Therefore, net electric field produced by the four particles at the square's center is zero.
To know more about electric field, refer
https://brainly.com/question/14372859
#SPJ4
Describe how solar radiation that arrives at the equator is redistributed around the earth through atmospheric circulation.
-unequal heating forms Hadley cells that redistribute heat
-unequal heating forms convection currents that redistribute heat
-unequal heating forms wind currents that redistribute heat
-unequal heating alters ocean currents that redistribute heat
Uneven heating patterns Uneven heating causes Hadley cells, which disperse heat; convection currents, which redistribute heat; wind currents, which redistribute heat; and ocean currents, which redistribute.
What type of heating for just a house is the least expensive?If you have access to natural gas as a heating source where you live, it will probably end up being the least expensive way of heat a house. Despite price increases, natural gas remains the most affordable space heating option. Electricity, gas, and heating oil are next, going from the next least expensive from the most expensive.
Which heating system is the most effective?The most effective type of house heating is a heat pump. Their biggest flaw is that they don't work well at extremely high or low temperatures. You can require space heaters all over your house during extremely cold weather, which reduces efficiency.
To know more about heating visit:
https://brainly.com/question/8348313
#SPJ4
the electric field lines on the left have twice the separation of those on the right. (a) If the magnitude of the field at A is 40 N/C, what is the magnitude of the force on a proton at A? (b) What is the magnitude of the field at B?
This means that if the field lines are near together (i.e., the field line density is greater), it means that the magnitude of the field is large at that location. The cross-sectional field lines should be close together if the field is of small magnitude.
The intersection of two electric field lines: what does it mean?Lines in an electric field cannot intersect. If they did, they would be telling you that a charge at that place would have a force that points in two distinct directions, which is completely illogical. Equipotential lines cannot cross at different potentials either.This means that if the field lines are near together (i.e., the field line density is greater), it means that the magnitude of the field is large at that location. The cross-sectional field lines should be close together if the field is of small magnitude.The cross-sectional field lines should be close together if the field is of small magnitude.To learn more about magnitude refer to:
https://brainly.com/question/24256733
#SPJ4
A car accelerates uniformly from rest and reaches a speed of 33.8 m/s in 4.7s the diameter of the tire is 64.6 cm find the number of revolutions the tire makes during this motion
The tire makes approximately 280.57 revolutions during this motion.
What are the revolutions?Generally, To find the number of revolutions the tire makes during this motion, we first need to find the distance traveled by the car.
Distance = Initial velocity x time + (1/2) x acceleration x time^2
Since the car starts at rest, the initial velocity is 0 m/s.
The acceleration is uniform, so we can use the formula:
Final velocity = Initial velocity + acceleration x time
In this case, the final velocity is 33.8 m/s, and the time is 4.7s.
So, acceleration = (33.8 m/s - 0 m/s) / 4.7s
= 7.19 m/s^2
Now we can use this value of acceleration to find the distance traveled:
Distance = 0 m/s x 4.7s + (1/2) x 7.19 m/s^2 x (4.7s)^2
= 570.98 m
To find the number of revolutions of the tire, we divide the distance traveled by the circumference of the tire.
The circumference of the tire is equal to the diameter x pi.
Circumference = 64.6 cm x 3.14
= 203.5 cm
Number of revolutions = Distance / Circumference
= 570.98m / (203.5 cm)
=280.57
Read more about revolutions
https://brainly.com/question/1291142
#SPJ1
A spring scale is used to exert a net force of 5.6 N on a cart, If the cart's mass is 340 grams, what is the cart's acceleration ?
Force = 5.6N
Mass = 340g = 0.34kg
Acceleration= Force/mass
= 5.6/0.34 = 16.4m/s²
What is the kinetic energy of a 1,678-kilogram boat moving at 4.6 m
Answer:
17,753.24 J (Joules)
Explanation:
To calculate the kinetic energy of an object, we use the formula:
Kinetic energy = 1/2 * mass * velocity^2
where mass is measured in kilograms and velocity is measured in meters per second.
Given that the boat has a mass of 1,678 kilograms and a velocity of 4.6 meters per second, we can substitute these values into the formula to find its kinetic energy:
Kinetic energy = 1/2 * 1,678 * (4.6)^2
Kinetic energy = 1/2 * 1,678 * 21.16
Kinetic energy = 17,753.24 J (Joules)
So the kinetic energy of the 1,678-kilogram boat moving at 4.6 m/s is 17,753.24 J (Joules).
A rotating platform with a radius of 2.0 m makes one complete turn every 3.0 s. The angular velocity of the platform is most nearly A 2.1 rad/s B 1.5 rad/s C 1.0 rad/s D 0.70 rad/s E 0.30 rad/s
The angular velocity of a rotating object is 2.1 rad/s. So option A is correct.
It is defined as the rate of change of its angular position, and it is measured in units of radians per second (rad/s).
The angular velocity of a rotating platform can be calculated using the formula: angular velocity = 2 * pi * (frequency of rotation)
Frequency of rotation = 1 / time for one complete rotation = 1 / 3 sec = 0.33 Hz
Therefore, the angular velocity of the platform is 2 * pi * 0.33 Hz = 2.09 rad/s
The answer is closest to A 2.1 rad/s
To know more about angular velocity:
https://brainly.com/question/20432894
#SPJ4
for best results, if not tested immediately, a semen sample should remain at which of the following temperatures following collection?
For best results, if not tested immediately, a semen sample should remain at a temperature 37 ºC. Thus, option C is correct.
What is temperature?Temperature is a physical property of matter that quantitatively expresses the common notions of hot and cold. Temperature is measured with a thermometer, which may be calibrated to a variety of temperature scales, including Celsius, Fahrenheit, Kelvin, and Rankine. The most commonly used scales are Celsius (formerly called centigrade) and Fahrenheit.
In scientific terms, temperature is the measure of the average kinetic energy of particles in a system. Temperature is an intensive property, meaning it is independent of the amount of matter in a system. For example, water at a given temperature is the same regardless of whether it is in a glass, a bucket, or an ocean.
This temperature range is the optimal temperature for preserving the viability of the sperm cells. If the sample is not tested immediately, it should be stored in a refrigerator or cooler with a temperature at or below this range to ensure the best possible results.
To know more about temperature click-
brainly.com/question/28590546
#SPJ4
Complete question:
For BEST results, if not tested immediately, a semen sample should remain at which of the following temperatures following collection?
a) 4 ºC
b) Room temperature
c) 37 ºC
d) -40 ºC
If we drop 2 objects of different weights from the same height, which one will reach the ground faster?
If we drop 2 objects of different weights from the same height, both of them will reach the ground at the same time.
Gravity, at the surface of a body like Earth, provides an acceleration to bodies and this acceleration is constant and its value is equal to 9.8m/s². This is because the Earth attracts big objects more than little ones, but the big ones have more inertia, which cancels out. So, all the bodies on the earth's surface fall at the same acceleration of 9.8m/s²
This acceleration due to gravity,g is independent of the mass of the body. The time of flight for any freely falling object depends on the value of acceleration due to gravity and its initial speed. So both the bodies reach the ground at the same time.
For further information about acceleration due to gravity, refer to the link:
https://brainly.com/question/3198512
#SPJ4
a collision at 30 mph will take any loose object in your car and give it the same force as if it were:
A collision at 30 mph will take any loose object in your car and give it the same force as if it were: shot from a canon.
What is the force of impact at 30 mph?Your body weight times the speed of the moving object equals the crash force. If you are holding your child while driving, you run the risk of crushing them if there is an accident. A 100-pound adult becomes a 3,000-pound force on the youngster in an accident at 30 miles per hour.About 40% of those struck by a car traveling at 30 mph will die as a result of their injuries, according to the U.S. Department of Transportation (DOT). To give you an idea, consider that 5 percent of people would not survive being hit by a car doing 20 mph.
To learn more about collision refer to:
https://brainly.com/question/4403635
#SPJ4
The pendulum in a grandfather clock has a period of 1.00 sec? If the clock's driving spring is allowed to run down, damping due to the friction will cause the pendulum to slow to an eventual stop. If the time constant for decay is 300 sec, how long will it take for the pendulum's swing to be reduced to half its initial amplitude?
It will take 207.9 sec for the pendulum's swing to be reduced to half its initial amplitude.
given:
T= time period initial = 1 sec
time constant = 300 sec
The pendulum's oscillation will eventually be stopped due to the air resistance offered by air . Oscillations will die down in a manner such that it makes an exponential curve.
We want the time at which the pendulum will stop due to friction
We know the formula for damping
[tex]A = A[/tex]' [tex]e^{-(\frac{t}{300} )}[/tex]
A= initial amplitude
A' = final amplitude = A/2
so 't' at
[tex]A = \frac{A}{2} \ 300[/tex] ㏑ (2 )
t= 207.94 sec
To learn more about damping
brainly.com/question/13161950
#SPJ4
A bicycle tire is spinning clockwise at 2.30 rad/s. During a time period =1.95 s, the tire is stopped and spun in the opposite direction, also at 2.30 rad/s. Calculate the change in the tire’s angular velocity and the tire’s average angular acceleration
If a bicycle tire is spinning clockwise at 2.30 rad/s. the change in the tire’s angular velocity and the tire’s average angular acceleration is: 2.63 rad/s².
How to find the average angular acceleration?Change in angular velocity
Δw = wf -wi
Δw = (2.30 rad/s) - (-2.30 rad/s)
= 4.60 rad/s
w_ is negative because it is in the clockwise direction.
Average angular acceleration:
Average angular acceleration = 4.60 rad/s/ 1.75s
Average angular acceleration = 2.63 rad/s²
Therefore the average angular acceleration is 2.63 rad/s².
Learn more about average angular acceleration here:https://brainly.com/question/29138741
#SPJ1
indicate whether the following statements are true or false. In each case give a reason for your answer. If W ⊂ Rn is a subspace and v ∈ Rn, then prW (v) is the least-squares approximation to v by a vector in W except when prW (v) = 0..
A. True
B. False
A swimmer capable of swimming with velocity v relative to water jumps in a flowing river having velocity u. The man swims a distance d downstream and returns back to the original position. Find out the time taken in complete motion.
a. 2dv/v^2 - u^2
b. dv/v^2 - u^2
c. 3dv/v^2 - u^2
d. 4dv/v^2 - u^2
The duration of the motion when a swimmer with a swimming velocity of v in relation to the water jumps into a river with a flowing velocity of u is measured as 2dv/v2 - u2.
What is motion?Motion is the gradual change in an object's position over time. Displacement, distance, velocity, acceleration, time, and speed are all used to describe motion. In physics, motion is a function of a body's position or orientation over time. Translation is defined as movement along a line or a curve. Rotation is a motion that modifies a body's orientation. Motion is the shift in an object's position with respect to time. When an object's position changes over time, it is said to be in motion. By mentioning a reference point, we are able to describe the location of an object. Relative motion exists. An object's distance is defined as the length of its total path.
Here,
t1=d/(u+v)
t2=d/(u-v)
t=t1+t2
=d/(u+v)+d/(u-v)
t=2dv/v²-u²
When a swimmer with a swimming velocity of v jumps into a river with a flowing velocity of u, the length of the motion is calculated as 2dv/v2 - u2.
To know more about motion,
https://brainly.com/question/13966796
#SPJ4
maria makes a graphic organizer to compare open, closed, and short circuits. she adds the labels shown. label 1: current flows in the circuit. label 2: this forms when a bulb burns out.
Maria compares three types of electrical circuits and their properties, behavior, and results using a graphical organizer. Label 1 represents an open circuit, label 2 a closed circuit, and label 3 a short circuit.
Label 1 refers to an open circuit where no current flows through the circuit because the flow of current has been interrupted or interrupted. This can happen if a switch is turned off, a fuse is blown, or a connection is loose.
Label 2 refers to a closed circuit in which current can flow through the circuit because there is a complete path for the current to flow. This is the normal operating state of the circuit.
Label 3 refers to short circuits that occur when there is an unintentional connection between the positive and negative sides of the circuit.
To learn more about the circuits at
https://brainly.com/question/27206933?referrer=searchResults
#SPJ4
hanging spring when a 0.30 kg mass is suspended from a massless spring, the spring stretches a distance of 2.0 cm. let 2.0 cm be the rest position for the mass-spring system. the mass is then pulled down an additional distance of 1.5 cm and released. results for question 7. 7 1.5 / 1.5 points calculate the period of resulting oscillation in si units. correct answer: 0.284 results for question 8. 8 0 / 1.5 points calculate the total mechanical energy of the system in si units. incorrect answer: 166
the total mechanical energy of the system is: 0.09187 Joule
What is spring constant?"spring constant" (plural: "spring constants") a property of a spring that is determined by the force acting on the spring to the displacement it produces. The stiffness of the spring is quantified by the spring constant, k. For various materials and springs, it varies. The spring becomes stiffer and more challenging to stretch as the spring constant increases.
Given that,
mass (m) = 0.30 kg
distance (x) = 2.0 cm. = 2 × 10⁻² m
Thus, for balancing condition,
kx = mg
or, k = mg /x
or, k = (0.30 × 10) / (2 × 10⁻²)
or, k = 150 N/m
So, the value of spring constant is 150 N/m
Next, time period (T) = 2π √(m /k)
or, T = 2π √(0.30 / 150)
or, T = 0.2808 sec
Total stretches in spring constant = 2 cm + 1.5 cm = 3.5 cm
Total mechanical energy = 1/2 k x²
Total mechanical energy = 1/2 × (150) × (2 × 10⁻²)²
Total mechanical energy = 0.09187 Joule
To know more about mechanical energy refer to:
https://brainly.com/question/24443465
#SPJ4
Suppose' a tree branch falls down to the ground with constant acceleration and takes 2 seconds to hit the ground. Which of the following statements regarding the path of the branch is true? A. Its acceleration is increasing during the time it falls B. It covers the same distance during the first second as it does during the last second. C. It covers more distance during the last second. D. It covers less distance during the last second.
The correct statements is it covers more distance during the last second.
What is mean by acceleration? The rate at which an object's velocity alters over time is called its acceleration. It has both magnitude and direction because it is a vector quantity. The difference between the change in velocity and the change in time is known as acceleration. In physics, acceleration is the rate of change of velocity with respect to time. It is measured in meters per second squared (m/s2). Acceleration is a vector quantity and is therefore described by both the magnitude and direction of the change in velocity. In everyday terms, acceleration is the rate at which an object speeds up, slows down or changes direction. Acceleration can be caused by a number of things, including a push, a pull, gravity, or a change in the net force acting on an object. Acceleration can also be caused by a change in the mass or shape of an object. In some cases, acceleration can be caused by a change in the direction of velocity.To learn more about acceleration refer to:
https://brainly.com/question/605631
#SPJ4
The chart shows the movement of a ball after several seconds. A 2-column table with 4 rows. The first column labeled A has entries 0, 4, 8, 12, 16. The second column labeled B has entries 0, 2.5, 6, 8, 10. Column A is on the x-axis, and Column B is on the y-axis. Which titles should replace A and B? Column A should be “Time,” and Column B should be “Position.” Column A should be “Position,” and Column B should be “Time.” Column A should be “Velocity,” and Column B should be “Speed.” Column A should be “Speed,” and Column B should be “Velocity.
The titles should replace A and B are Column A should be “Time,” and Column B should be “Position.”
What is the position of the ball after 4 seconds? How long does it take for the ball to reach a position of 8?At 4 seconds, the position of the ball is at (4,2.5). This is indicated on the chart by the intersection of the two lines on the 4th point of the x-axis (column A) and the 2.5th point of the y-axis (column B).It takes 4 seconds for the ball to reach a position of 8. This is evident from the chart as the 8th point of the x-axis (column A) intersects with the 10th point of the y-axis (column B). This intersection indicates the position of the ball at 8 seconds. Thus, it can be concluded that it took 4 seconds for the ball to reach a position of 8. This is in line with the increasing increments of 4 on the x-axis and 2.5 on the y-axis, as presented in the chart.To learn more about movement of ball refer to:
https://brainly.com/question/25743369
#SPJ1
A skater is standing still on a frictionless ice rink. Her friend throws a Frisbee straight to her. In which of the following cases is the largest momentum transferred to the skater?
(a) The skater catches the Frisbee and holds onto it.
(b) The skater catches the Frisbee momentarily, but then drops it vertically downward.
(c) The skater catches the Frisbee, holds it momentarily, and throws it back to her friend.
The largest momentum transferred to the skater is the skater catches the Frisbee, holds it momentarily, and throws it back to her friend.
The skater stands on a frictionless surface and his friend Frisbee starts moving behind him. The lack of friction makes the skater unstoppable.
However, when the skater returns to his friend through the Frisbee again, there is a backward force that increases the skater's speed. So and momentum is directly proportional to velocity, so as velocity increases so does momentum.
In Newtonian mechanics, momentum (more precisely, linear or translational momentum) is the product of an object's mass and velocity. A vector quantity that has magnitude and direction. If m is the object's mass and v is its velocity (which is also a vector quantity), then the object's momentum p is p = mv.
Advanced formulations of classical, Lagrangian and Hamiltonian mechanics allow the choice of coordinate systems containing symmetries and constraints. In these systems the conserved quantity is the generalized momentum, which is generally different from the momentum defined above. The generalized concept of momentum carries over into quantum mechanics and becomes the operator of the wavefunction. The momentum and position operators are related by the Heisenberg uncertainty principle.
Learn more about Momentum:
https://brainly.com/question/24030570
#SPJ4
Changes in the quantity and quality of light have important implications for life in aquatic environments, both by influencing the quantity and distribution of productivity and by influencing the vertical profile of temperature with water depth.
Changes in the quantity and quality of light can have significant impacts on aquatic environments, both on the organisms that live there and on the physical characteristics of the water. Some key impacts include:
What are the changes in quantity and quality of light that can have significant impact?
Productivity: Light is a key factor in photosynthesis, the process by which plants and algae produce food. Changes in the quantity or quality of light can affect the amount of productivity in an aquatic environment, leading to changes in the distribution and abundance of different species.Temperature: Light can also affect the temperature of water, particularly in deeper parts of the water column. In the absence of light, water at the bottom of a lake or ocean will be cooler than water at the surface. Changes in the quantity or quality of light can alter this temperature profile, with implications for the organisms that live there.Distribution of species: Light is a major factor influencing the distribution of aquatic organisms. For example, many species of fish and other aquatic animals live in areas of the water column that receive a lot of light, while other species prefer areas with less light. Changes in the quantity or quality of light can shift the distribution of these species, leading to changes in the overall community structure.Photosynthetic organisms: Changes in light intensity and quality can affect the survival, growth and reproduction of photosynthetic organisms like phytoplankton and seaweed.Light pollution: Artificial light sources can disrupt the natural light cycle of aquatic organisms, affecting their behavior, reproduction and survival.Overall, changes in the quantity and quality of light can have significant and wide-ranging impacts on aquatic environments, affecting everything from the productivity and temperature of the water to the distribution and survival of different species.
To learn more about light refer:
https://brainly.com/question/30978
#SPJ4
8. The Earth orbits the Sun at a distance of 1.46x1011 m from center to center. What is the strength of the Sun’s gravitational field at this distance?
The strength of the Sun's gravitational field at this distance is [tex]0.622m/s^2[/tex]
What is Gravitational field?A gravitational field is defined as the model used to explain the effects that a massive body exerts in the space around it exerts a force on another massive body. Therefore, a gravitational field is used to explain gravitational phenomena, and it is measured in newtons per kilogram.
The acceleration due to gravity on the surface of the earth is given by;
[tex]g = GM/R^2[/tex]
Where, g is the acceleration due to gravity
G is Gravitational constant [tex](6.673 * 10^-^1^1 Nm^2 kg^-^2)[/tex]
M is the mass of the planet [tex](1.99* 10^3^0 kg)[/tex]
R is the radius of planet
So, for above given information, [tex]g= \frac{6.022 * 10^-^1^1* 1.99* 10^-^3^0}{(1.46* 10^1^1)^2}[/tex]= [tex]0.622m/s^2[/tex]
Thus, the strength of the Sun's gravitational field at this distance is [tex]0.622m/s^2[/tex].
Learn more about Gravitational force, here:
https://brainly.com/question/12324569
#SPJ1
Star A has a magnitude of 9.5; Star B, 5.5; and Star C, 2.5. Which is brightest? Which are visible to the unaided eye? Which pair of stars has a flux ratio of about 16?
Star A has a magnitude of 9.5, star B has a magnitude of 5.5, and star C has a magnitude of 2.5, so star C is the brightest, while star B is visible but star A is not, and the flux of the star is 16, which is the ratio of star A to star B ( [tex]{2}^{9.5-5.5}=16[/tex])
What is the significance of the flux of the star?The star's flux is significant because it explains the amount of light emitted by the star, is useful for studying the star's brightness, and can be used to infer the star's distance from Earth, give the idea of a collision with Earth, and so on.
As a result, star A has a magnitude of 9.5, star B has a magnitude of 5.5, and star C has a magnitude of 2.5, so star C is the brightest, while star B is visible but star A is not, and the flux of the star is 16, which is the ratio of star A to star B.
Learn more about the flux of the star here.
https://brainly.com/question/28458370
#SPJ1
if a wave is traveling at a velocity of 120 m/s and has a frequency of 5 hz, which of the following can be determined? A.The mass of the wave. B. The speed of the wave. C.The wavelength of the wave. D. The direction of the wave.
If a wave has a frequency of 5 Hz and is moving at a speed of 120 m/s, its wavelength is 24 m.
Given,
Velocity =120m/s
Frequency=5Hz
So the Wavelength of the wave is,
[tex]\lambda =\frac{v}{f}[/tex]
[tex]\lambda =\frac{120}{5}=24m[/tex]
[tex]\lambda =24m[/tex]
So the Wavelength of the wave is 24m
The number of waves that pass through a fixed point in a given amount of time is defined as the frequency. If a wave takes 1/2 second to pass, the frequency is 2 per second. If it takes one-hundredth of an hour, the frequency is one hundred per hour.
After passing through a series of events or positions and returning to its original state, a body in periodic motion is said to have gone through one cycle or one vibration. Additionally, see angular velocity and simple harmonic motion.
The frequency is 2 per second if the period or time interval, required to complete one cycle or vibration is 1/2 second; 100 per hour if the period is 1/100 of an hour.
Learn more about frequency here:
https://brainly.com/question/14400059
#SPJ4
which of the answers below best describes the discussion between maria and oliver? maria and oliver are discussing the ranking of buoyant forces on three different objects. maria and oliver are discussing how to correctly determine the pressure at a particular depth in a fluid. maria and oliver are discussing how to correctly determine the number and magnitude of forces on a volume of water. maria and oliver are discussing whether the bouyant force is influenced by the mass of an object. grade summary deductions 0% potential 100% submissions attempts remaining: 3 (33% per attempt) detailed view
Oliver and Maria are debating how to precisely determine the fluid's pressure at a particular depth.
What forces need to be considered in order to understand how a sphere falls in a fluid?
Stokes' law describes how spheres settle in a Newtonian fluid. A particle will sink if the buoyant force acting on a sphere submerged in a Newtonian fluid is not equal to or greater than the gravitational force acting on the sphere. The net downward force on a sphere is what separates the settling force from the buoyant force.
What connection exists between point pressure and depth in a fluid?
Because a liquid's pressure also increases with depth, the pressure of a liquid is inversely proportional to its depth.
Learn more about buoyancy force here
brainly.com/question/13267336
#SPJ4
let the samples of the noise voltage, v (nt) be jointly gaussian random variables. show that x(t) is a gaussian process.
Since x(t) is a linear function of v(nt) which is jointly Gaussian, and the mean of x(t) is a linear function of t, x(t) is also a Gaussian process.
What is Gaussian process?A Gaussian process is a stochastic process whose realizations are Gaussian random variables. To show that x(t) is a Gaussian process, we need to show that:The mean of x(t) is a linear function of t.The covariance function of x(t) is a valid covariance function.The mean of x(t) is defined as E[x(t)], where E[] denotes the expectation operator. Since the noise voltage v(nt) is jointly Gaussian, it follows that x(t) = v(nt) is also Gaussian, and thus its mean is a linear function of t.The covariance function of x(t) is defined as C(s,t) = E[(x(s) - E[x(s)]) (x(t) - E[x(t)])].Since v(nt) is jointly Gaussian, the covariance function of x(t) is also a valid covariance function.Therefore, x(t) is a Gaussian processx(t) = v(nt) is jointly GaussianSince x(t) is a linear function of v(nt) which is jointly Gaussian, and the mean of x(t) is a linear function of t, x(t) is also a Gaussian process.The covariance function of x(t) is a valid covariance function, as it is derived from jointly Gaussian variables.To learn more about Gaussian process refer:
brainly.com/question/13427232
#SPJ4
The scalar product of the vectors A=3i+4j-5k and B=-i+j-2k
The scalar product of the vectors A = 3i + 4j - 5k and B = -I + j - 2k is -9.
The scalar product (also known as the dot product) of two vectors is a scalar quantity that can be calculated by multiplying the magnitudes of the two vectors and the cosine of the angle between them. The formula to calculate the scalar product of two vectors A and B is:
A.B = |A| |B| cos(theta)
To find the scalar product of two vectors we can also use the following formula:
A.B = (A.i) (B.i) + (A.j) (B.j) + (A.k) (B.k)
where A.i, A.j, A.k, B.i, B.j, B.k are the projections of vectors A and B on the i, j, and k axis respectively.
So, in this case, we have:
following A = 3i + 4j - 5k and B = -i + j - 2k
A.B = (3)(-1) + (4)(1) + (-5)(-2) = -3 + 4 - 10 = -9
Therefore, the scalar product of the vectors A = 3i + 4j - 5k and B = -I + j - 2k is -9.
To learn more about Scalar products visit the link:
https://brainly.com/question/28007613
Refer to the image attached.
if the people are all lined up on the street at different blocks, and the police siren starts at block 3, which statement describes what block each person is standing at? wycleff is on block 1, lilly is on block 4, quincy is on block 12, and emilia is on block 17. lilly is on block 1, wycleff is on block 4, quincy is on block 12, and emilia is on block 17. lilly is on block 1, wycleff is on block 4, emilia is on block 12, and quincy is on block 17. wycleff is on block 1, lilly is on block 4, emilia is on block 12, and quincy is on block 17.
Wycleff is on block 1, Lilly is on block 4, Emilia is on block 12, and Quincy is on block 17 is the correct statement about each person standing at block.
Simple definition of the Doppler effect.As a source and observer move closer or farther apart, the Doppler effect, which is a phenomenon in physics, causes the frequency of sound, light, or other waves to rise or fall. When a source emits waves, those waves are compressed as they approach the observer.
Wycleff could hear a low-pitched sound the entire time, indicating that the police car was relocating away from him. He was thus in block 1.
A Doppler effect (change in pitch) was the first thing Lilly noticed. She was at block 4, so the car must have passed her first.
After Lilly, Emilia noticed a Doppler effect. She was at block 12 when the car passed Lilly before passing her.
The entire time, Quincy heard a high-pitched sound, which indicated that the police car was approaching. He was thus in block 17.
To know more about Doppler effect visit:
https://brainly.com/question/15318474
#SPJ4
If you push a particle of mass M inthe direction in which it is already moving, you expect theparticle's speed to increase. If you push with a constant forceF, then the particle will accelerate with accelerationa=F/M (from Newton's 2nd law).
A. Enter a one- or two-word answer that correctly completes thefollowing statement.
If the force is applied for a fixed interval of time t, then the _____ of the particle will increase by an amountat.
B. Enter a one- or two-word answer that correctly completes thefollowing statement.
If the force is applied over a given distance D, along the path of the particle, thenthe _____ of the particle will increase byFD.
C. If the initial kinetic energy of the particle isK1, and its final kinetic energy isKf, express Kfin terms of K1 and thework W done on theparticle.
D. Now, consider whether the following statements are true orfalse:
The dot product assures that the integrand is alwaysnonnegative.
The dot product indicates that only the component of theforce perpendicular to the path contributes to theintegral.
The dot product indicates that only the component of theforce parallel to the path contributes to the integral.
E. Assume that the particle has initial speedv1. Find its final kinetic energy Kf in terms ofv1, M, F, andD.
F. What is the final speed of the particle?
A. Speed ; B. kinetic energy ; C. Kf = K1 + W ; D. The statements are false. E. Kf = K1 + (FD) ; F. v = sqrt(2Kf/M).
What is kinetic energy?In physics, kinetic energy of an object is the energy that it possesses due to motion.
A. If the force is applied for a fixed interval of time t, then speed of the particle will increase by an amount at.
B. If the force is applied over given distance D, along the path of particle, then kinetic energy of the particle will increase by FD.
C. Kf in terms of K1 and work W done on particle is : Kf = K1 + W
D. The statements are false. The dot product does not guarantee that the integrand is always nonnegative and also it does not indicate that only the component of force perpendicular or parallel to the path contributes to integral.
E. Final kinetic energy Kf in terms of v1, M, F, and D is Kf = K1 + (FD)
F. Final speed can be determined using the formula, Kf = 1/2 * M * v^2. where v is final speed. It can be rearranged to find v = sqrt(2Kf/M).
To know more about kinetic energy, refer
https://brainly.com/question/8101588
#SPJ4
