10. Technician A says to make the finish cut at the slowest speed when machining brake drums. Technician B says that the drum should not exceed its discard diameter. Who is correct?

Answers

Answer 1

When milling, technician A advises using the slowest speed for the end cut. According to technician B, the drum shouldn't be larger than its disposal diameter.

What is the process of milling?

Cleaning, grading, breaking down, sizing, separating, or classifying dry bulk materials are all included in the term "milling process." The mill is used in the actual milling process to grind, cut, or crush solid bulk materials into smaller bits. Ingilling is the practise of using a specialised machine to grind, cut, press, or crush a material. Cutting away material with a spinning cutter that has several teeth is called milling.

Know more about disposal Visit:

https://brainly.com/question/14732695

#SPJ1

Related Questions

An air-conditioning system's automatic controller might directly control the

A. conversion of pneumatic energy to hydraulic signal pressure.
B. thermostat's setpoint temperature.
C. motor of a large condenser fan.
D. sensitivity of the ladder logic.

Answers

Note that an air-conditioning system's automatic controller might directly control the: "motor of a large condenser fan" (Option C)

What is a Condenser Fan?

A condenser fan is a type of fan that is found near the condenser, as the name implies. Its purpose is to remove heat from the refrigerant inside the hollow passages of the condenser. When your air conditioner is turned on, the refrigerant at the evaporator coil absorbs heat from the inside of your home.

The automatic controller of an air-conditioning system is a device that controls the operation of the air-conditioning system. It has the ability to directly control the motor of the large condenser fan. This motor is in charge of blowing air over the condenser coils, which aids in the dissipation of heat absorbed by the refrigerant.

Learn more about air conditioning:
https://brainly.com/question/29648889?
#SPJ1

Anna is very picky about the temperature in her home and wants full control of air flow and heat/cooling. She should install a system that includes

A. floating control.
B. an automated mixing chamber.
C. two-position control.
D. a low differential.

Answers

Where Anna is very picky about the temperature in her home and wants full control of airflow and heat/cooling. She should install a system that includes: "a low differential" (Option D)

What is a Low Differential?

The temperature differential in HVAC terms refers to the temperature difference between the inside and outside areas of the house.

The thermostat has an adjustable temperature differential setting that determines how frequently your system cycles. The lower the differential setting, the more frequently your system will cycle and the tighter the temperature will be maintained.

Learn more about Differential Heating:
https://brainly.com/question/28033741
#SPJ1

Other Questions

Examine the number line,and then choose the correct symbol to complete each statement Is gravity dependent on mass or size?. What is the product of 7x 6 2?. In terms of the relationship between listening and culture, which of the following is true concerning feedback?Positive feedback is always preferable to negative feedback regardless of culture.People from high-context cultures (such as Japan and Korea) generally appreciate honest, open feedback.Perceptions of appropriate feedback vary from culture to culture.Eye contact is a universal symbol of good listening For each graph, determine the y-intercept using the slope formula. Write the y-intercept in coordinate form. find the solution set x^2 -8x+ 7=0 What are the 3 main purposes of mitosis?. you are hiking into unfamiliar terrain. what is the best way to keep your bearings? correct for declination and then follow the orienting arrow on your compass. shade in the contour intervals on your topographic map as you climb uphill. take frequent compass readings and plot your progress on a map. follow the contour lines on your topographic map. Which of the following is TRUE?a. profit-maximizing behavior occurs only in perfectly competitive marketsb. additional units of a good should be produced as long as MRc. the profit-maximizing solution occurs where MR=MCd. the profit-maximizing solution occurs where MR>MC 1. contains classified ads listing employment opportunities: f contains classified ads listing employment opportunities 2. use this to check sites that help people find jobs: b use this to check sites that help people find jobs 3. a department at your school that may have job listings and can help with writing a resume: c a department at your school that may have job listings and can help with writing a resume 4. check here for a list of facilities and agencies that hire nursing assistants: d check here for a list of facilities and agencies that hire nursing assistants 5. they may know of possible job openings: e they may know of possible job openings 6. many schools and facilities have one of these where job opportunities may be posed: a many schools and facilities have one of these where job opportunities may be posed which of the items below can be positive effects of cities with a higher cost of living? (check all that apply) confrontation during a single session and over a series of interviews may be measured on a 5-point scale called the client change scale. which of the following represents this scale? Why did Jane Addams found the Hull House? A mixture of 0.4850 M CO and 0.4300 M Cl2 is enclosed in a vessel and heated to 1000 K .CO(g)+Cl2(g)COCl2(g)c=255.0 at 1000 KCalculate the equilibrium concentration of each gas at 1000 K . Identify and explain ONE example after 1450 C.E. in which syncretism played an important role in the spread of religious or cultural traditions. which law states that volume increases with temperature Solve this equation for the given domain.cos(2x + 45) = 0.8 for 0 x 180 when recording a business transaction the amount is always entered first because it is the most important part of the journal entry You buy 4 small candles and 2 large candles for $14. Your friend buys 5 small candles and 3 large candles for $20. What is the cost of each small candle? of each large candle?Each small candle costs $_ and each large candle costs $_. Please answer it brainless

10. Technician A says to make the finish cut at the slowest speed when machining brake drums. Technician B says that the drum should not exceed its discard diameter. Who is correct?​

Answers

Related Questions

Answers

Answers

10. Technician A says to make the finish cut at the slowest speed when machining brake drums. Technician B says that the drum should not exceed its discard diameter. Who is correct?