150-w light bulb is designed to operate at 110 v dc. how much current does it draw? 150-w light bulb is designed to operate at 110 v dc. how much current does it draw? 0.73 a 15 a 1.4 a 2.0 a

Answers

Answer 1

The 150-watt light bulb draws 1.4 amperes of current when operated at 110 volts DC.

The formula for calculating current (I) is I = P / V, where P is power in watts and V is voltage in volts. Using this formula, we can calculate the current drawn by the 150-watt light bulb as follows:

I = P / V
I = 150 / 110
I = 1.3636



To calculate the current drawn by the light bulb, we can use Ohm's Law, which states that Power (P) = Voltage (V) * Current (I). We are given the power (150 watts) and the voltage (110V), so we can rearrange the equation to solve for the current:

I = P / V

Plugging in the given values:

I = 150 watts / 110 volts

I ≈ 1.36 amps

The 150-watt light bulb operating at 110V DC draws approximately 1.36A of current. Out of the given options, 1.4A is the closest value to the calculated current.

To know more about light bulb, visit;

https://brainly.com/question/8979272

#SPJ11


Related Questions

How much heat is released when a 10. 0-g sample of iron cools from 75. 0°c to 25. 5 °c? the specific heat capacity of iron is 0. 449 j/g · °c.

Answers

222.53 J of heat is released when a 10.0 g sample of iron cools from 75.0°C to 25.5°C.

The heat released can be calculated using the formula:

Q = m * c * ΔT

Where Q is the amount of heat released, m is the mass of the iron, c is the specific heat capacity of iron, and ΔT is the change in temperature.

Given:

m = 10.0 g

c = 0.449 J/g°C

ΔT = 75.0°C - 25.5°C = 49.5°C

Substituting the values in the formula, we get:

Q = 10.0 g * 0.449 J/g°C * 49.5°C

Q = 222.53 J

what is temperature?

Temperature is a measure of the average kinetic energy of the particles in a substance or system. It is commonly measured using a thermometer and is usually expressed in degrees Celsius (°C) or Fahrenheit (°F) in everyday life.

To learn more about iron visit:

brainly.com/question/30570319

#SPJ11

Use a(t) = -32 ft/sec^2 as the acceleration due to gravity. (Neglect air resistance.)
A balloon, rising vertically with a velocity of 16 feet per second, releases a sandbag at the instant when the balloon is 48 feet above the ground.
a) How many seconds after its release will the bag strike the ground?
b) At what velocity will it strike the ground?

Answers

The bag will take 3 sec to strike the ground after release and velocity it will carrying will be - 80 ft/ s.

Elaborating:

a. h ( t) = -16 t² + 16t + 48

h(t) = 0

-16 t² + 16t + 48 = 0

-t² + t + 3 = 0

(-t - 1) (t - 3) = 0

t = 3 sec.

Ignoring t = -1 as time can not be negative .

b. Vertical speed after release = 16 - 32t

                                      = 16- 32 × 3

                                   = 16 - 96 = -80 ft / s

                                      -80 ft / s ( negative is the down direction )

What is the speed increase because of gravity?

The speed increase because of gravity at or close to Earth's surface is 9.8 m/s². A force that pulls objects toward the ground is called gravity. The acceleration of falling objects is caused by gravity. Acceleration is a change in velocity, which is a measurement of motion's speed and direction.

Velocity:

An object's velocity is its directional speed as an indicator of its rate of change in position when viewed from a specific frame of reference and measured using a specific standard of time.

Learn more about velocity:

brainly.com/question/24445340

#SPJ4

Who concluded that heat is produced by motion?

Answers

The scientist who concluded that heat is produced by motion was James Prescott Joule, an English physicist and mathematician. In the 1840s, Joule conducted a series of experiments that led him to discover the relationship between heat and mechanical work, now known as Joule's First Law. This law states that the amount of heat produced by the mechanical work of a moving object is directly proportional to the work done.

Joule's experiments involved a variety of mechanisms, such as paddle wheels and weights, to generate heat through motion. One of his most famous experiments involved a falling weight that turned a paddle wheel in a container filled with water. Joule observed that the temperature of the water increased as the weight fell, which confirmed his hypothesis that the mechanical work done by the falling weight was converted into heat.

This groundbreaking discovery contributed to the development of the First Law of Thermodynamics, which states that energy cannot be created or destroyed, only converted from one form to another. Joule's work also laid the foundation for the modern concept of energy conservation and played a crucial role in the transition from the caloric theory of heat to the more accurate kinetic theory.

TO KNOW MORE ABOUT kinetic theory. CLICK THIS LINK

brainly.com/question/1434921

#SPJ11

use the inner product in the vector space of continuous functions on the domain to find the orthogonal projection of onto the subspace spanned by and . (caution: and do not form an orthogonal basis of .)

Answers

To use the inner product in the vector space of continuous functions on the given domain to find the orthogonal projection of a given function onto the subspace spanned by two other functions, which do not form an orthogonal basis of the space.

To do this, we first need to find an orthogonal basis for the subspace spanned by the two given functions. We can use the Gram-Schmidt process to find an orthogonal basis, which involves finding the projection of one function onto the other and subtracting it from the original function, then normalizing the resulting vector.

Once we have an orthogonal basis for the subspace, we can use the formula for orthogonal projection to find the projection of the given function onto the subspace. This formula involves taking the inner product of the given function with each vector in the orthogonal basis, then multiplying each inner product by the corresponding vector and summing the results.

Overall, the explanation for finding the orthogonal projection of a function onto a subspace in the vector space of continuous functions involves finding an orthogonal basis for the subspace using the Gram-Schmidt process and using the formula for orthogonal projection to calculate the projection of the given function onto the subspace.

To know more about orthogonal refer to

https://brainly.com/question/2292926

#SPJ11

The current in the secondary coil of a step-up transformer is 1.25 A when the current in the primary coil is 0.30 A. Determine the turns ratio, Ns/Np, of the transformer.
A) 5.6
B) 4.2
C) 0.24
D) 0.18
E) 0.12

Answers

The turns ratio of the transformer is approximately 4.2.

The turns ratio, Ns/Np, of the transformer can be calculated using the formula:
Ns/Np = Is/Ip
where Ns is the number of turns in the secondary coil, Np is the number of turns in the primary coil, Is is the current in the secondary coil, and Ip is the current in the primary coil. Substituting the given values, we get:
Ns/Np = 1.25 A / 0.30 A = 4.17.
Therefore, the turns ratio of the transformer is approximately 4.2.

To know more about transformer, click here https://brainly.com/question/15200241

#SPJ11

If the electric field is in the positive x direction and has a magnitude given by E = Cx2, where C is a constant, then the electric potential is given by V =: A.2Cx B.-2Cx C.Cx3/3 D.-Cx3/3

Answers

According to the question the electric potential is given by V = Cx³/3.

What is electric potential?

Electric potential is a measure of the potential energy of a system of charged particles in an electric field. It is the energy per unit charge that is required to move a particle from one point to another in an electric field. Electric potential is measured in volts and is equal to the amount of work done to move a unit charge from one point to another. Electric potential is a scalar quantity that is determined by the electric field strength, the distance between two points, and the charge of the particles in the electric field. Electric potential is also referred to as voltage.

The electric potential V is related to the electric field E through the equation V = -∫E · dr,
where dr is a small displacement vector.
In this case, the electric field is in the positive x direction with magnitude E = Cx².
Integrating this equation yields V = -∫Cx² · dr = -Cx³/3. Therefore, the electric potential is given by V = Cx³/3.

To learn more about electric potential
https://brainly.com/question/26978411
#SPJ4

Field observations suggest that a migrating ruby-throated hummingbird can fly across the gulf of mexico on a nonstop flight traveling a distance of about 800 km. Assuming that the bird has an average speed of 40. 0 km/hr and an average power consumption of 1. 70 w , how many grams of fat mfat does a ruby-throated hummingbird need to accomplish the nonstop flight across the gulf of mexico?.

Answers

A ruby-throated hummingbird needs approximately 3.25 grams of fat to accomplish the nonstop flight across the Gulf of Mexico.

To determine how many grams of fat (mfat) a ruby-throated hummingbird needs to accomplish a nonstop flight across the Gulf of Mexico, we need to follow these steps:


1. Calculate the time (t) required for the nonstop flight:


Distance = 800 km


Average speed = 40.0 km/hr


Time (t) = Distance / Average speed

             = 800 km / 40.0 km/hr

            = 20 hours


2. Calculate the total energy consumption (E) during the flight:


Average power consumption = 1.70 W (watts can be expressed as joules per second)


Time (t) in seconds = 20 hours * 60 minutes/hour * 60 seconds/minute

                               = 72000 seconds


Energy (E) = Average power consumption * Time (t)

                 = 1.70 W * 72000 s

                 = 122400 J (joules)



3. Calculate the energy (Efat) stored in 1 gram of fat:


1 gram of fat provides approximately 9 kcal (kilocalories) of energy, and 1 kcal equals 4184 J (joules). So,


Efat = 9 kcal/g * 4184 J/kcal

       = 37656 J/g


4. Finally, calculate the required mass of fat (mfat) for the nonstop flight:


mfat = Total energy consumption (E) / Energy per gram of fat (Efat)

        = 122400 J / 37656 J/g

        = 3.25 g


So, a ruby-throated hummingbird needs approximately 3.25 grams of fat to accomplish the nonstop flight across the Gulf of Mexico.

To know more about ruby-throated refer here

brainly.com/question/589709#

#SPJ11

What happens if we increase the number of slits to N?

Answers

If the number of slits is increased from two to N, the interference pattern will become more complex with an increased number of bright and dark fringes.

What is interference ?

Interference is the disruption of a signal by another signal that has a similar frequency. It occurs when two signals of the same frequency are close enough to each other that they overlap and create interference. This can cause a reduction in the quality of a signal, resulting in a decrease in sound or picture quality, or even complete loss of the signal. Interference can also be caused by external sources such as electrical devices, buildings, or other devices that produce similar frequencies. Interference can also be caused by natural occurrences such as weather conditions, solar flares, or other natural phenomena.

As the number of slits increases, the distance between the fringes decreases. This is because the path difference between light passing through the slits decreases when the number of slits increases, leading to higher interference.

To learn more about interference

https://brainly.com/question/30670739

#SPJ4

The type of energy that deals with the movement of an object is Kinetic PotentialChemicalElastic

Answers

The type of energy that deals with the movement of an object is Kinetic Energy.

Kinetic energy is the energy an object possesses due to its motion, while potential energy is the energy an object possesses due to its position or state. Chemical energy is the energy stored in chemical bonds between atoms and molecules, while elastic energy is the energy stored in an object when it is deformed or compressed.

In the context of movement, the energy associated with an object's motion is kinetic energy. For example, a moving car possesses kinetic energy due to its motion. As the car moves faster, its kinetic energy increases. On the other hand, when an object is stationary, it has no kinetic energy but may possess potential energy due to its position or state.

The type of energy that deals with the movement of an object is kinetic energy.

To know more about  Kinetic Energy, click here:

https://brainly.com/question/26472013

#SPJ11

What things about the resistors in this circuit are the same for all three?A. Current IB. Potential difference (delta V)C. Not enough information

Answers

Potential difference, is same for all three resistors.

Hence, the correct option is B.

A. The current, on the other hand, is not the same for all three resistors, as it depends on the resistance of each resistor and the total resistance of the circuit.

B. The potential difference (delta V) across each resistor is the same in this circuit. This is because the circuit is a series circuit, meaning that there is only one path for the current to flow. Therefore, the same amount of charge flows through each resistor, resulting in the same potential difference across each resistor.

Hence, the correct option is B.

To know more about resistors here

https://brainly.com/question/31493909

#SPJ4

f the force were perpendicular to r with arrowa but gave the same torque as in the preceding question, what would its magnitude be

Answers

If the force were perpendicular to the vector r with an arrow, but gave the same torque as in the preceding question, its magnitude would depend on the angle between the force and the vector r.

When a force is applied at an angle to a lever arm, the torque produced is equal to the product of the force and the perpendicular distance between the force and the axis of rotation.

In this case, since the force is perpendicular to the vector r, the perpendicular distance is simply the length of the vector r. Therefore, the magnitude of the force would be equal to the torque divided by the length of the vector r.

It is important to note that the direction of the force is not parallel to the direction of the torque, as in the preceding question. Instead, the force and torque are orthogonal to each other, meaning they act in different directions. This type of force is known as a radial force and is often encountered in circular motion problems.

For more about perpendicular:

https://brainly.com/question/18271653

#SPJ11

When two capacitors are connected in series, the equivalent capacitance of the combination is 120 µF. When the two are connected in parallel, however, the equivalent capacitance is 480 µF. What are the capacitances of the individual capacitors?

Answers

When capacitors are connected in series, their Equivalent capacitance is found by adding the inverse of their individual capacitances, and then taking the inverse of that sum. So, if we let C1 and C2 be the capacitances of the individual capacitors, we can write:

1/120 = 1/C1 + 1/C2

When capacitors are connected in parallel, their equivalent capacitance is found by simply adding their individual capacitances. So, we can write:

480 = C1 + C2

Now we have two equations with two unknowns, which we can solve simultaneously. Rearranging the first equation, we get:

1/C1 + 1/C2 = 1/120

Multiplying both sides by C1C2, we get:

C2 + C1 = 120C1C2

Using the second equation, we can substitute C2 = 480 - C1, giving:

480 - C1 + C1 = 120C1(480 - C1)

Simplifying, we get:

480 = 120C1^2 - 120C1^3

Dividing by 120 and rearranging, we get:

C1^3 - C1^2 + 4 = 0

We can solve this cubic equation using a numerical method, such as Newton-Raphson iteration. After several iterations, we find that one solution is:

C1 ≈ 9.877 µF

Substituting this value into the second equation, we find:

C2 ≈ 470.123 µF

So the capacitances of the individual capacitors are approximately 9.877 µF and 470.123 µF when connected in series, and approximately 9.877 µF and 470.123 µF when connected in parallel.

learn more about Equivalent capacitance here:

https://brainly.com/question/30905469

#SPJ11

solenoid with 200 loops is 55 cm long. it has a current of 2.2 a . what is the magnetic field in this solenoid? express your answer with the appropriate units.

Answers

The magnetic field in a solenoid can be calculated using the equation B = μ₀ * n * I, where B is the magnetic field, μ₀ is the permeability of free space (4π x 10⁻⁷ T*m/A), n is the number of loops per unit length (n = N/L, where N is the total number of loops and L is the length of the solenoid), and I is the current.

In this case, the solenoid has 200 loops and is 55 cm long, so the number of loops per unit length is n = 200 / (0.55 m) = 363.6 loops/m. The current is 2.2 A.

Plugging these values into the equation, we get:

B = μ₀ * n * I
B = (4π x 10⁻⁷ T*m/A) * (363.6 loops/m) * (2.2 A)
B = 1.63 x 10⁻³ T

Therefore, the magnetic field in this solenoid is 1.63 x 10⁻³ T (tesla), which is the appropriate unit for magnetic field.
The magnetic field inside a solenoid can be calculated using the formula:

B = μ₀ * n * I

where B is the magnetic field, μ₀ is the permeability of free space (4π × 10⁻⁷ T·m/A), n is the number of turns per unit length (loops/m), and I is the current (A).

Given that the solenoid has 200 loops and is 55 cm long, we can find the number of turns per unit length:

n = 200 loops / (55 cm × (1 m/100 cm)) = 200 loops / 0.55 m = 363.64 loops/m

Now, we can calculate the magnetic field:

B = (4π × 10⁻⁷ T·m/A) * (363.64 loops/m) * (2.2 A) ≈ 1.01 × 10⁻³ T

Therefore, the magnetic field inside the solenoid is approximately 1.01 × 10⁻³ Tesla (T).

To know more about solenoid visit:

https://brainly.com/question/15504705

#SPJ11

Our galaxy consists of a large, nearly flat ____ with a central ____ , all surrounded by a vast ____ .

Answers

Our galaxy consists of a large, nearly flat disk with a central bulge;  all surrounded by a vast halo

What is known as a galaxy?

A galaxy is a vast collection of stars, solar systems, gas, and dust. Gravity holds a galaxy together. A supermassive black hole also resides in the center of our galaxy, the Milky Way.

By their shape, galaxies are categorized. There are three basic types: irregular, spiral, and elliptical. Spiral galaxies are conceivably the most well-known type of galaxy. A relatively flat disk with spiral arms and a central "bulge" give them a distinctive shape.

To learn more about galaxy use:

https://brainly.com/question/13956361

#SPJ4

which of the following is not described in the text as one of the four main explanations for the increase in adhd from 1990 to the present?

Answers

There are several factors that have contributed to the increase in ADHD diagnosis rates from 1990 to the present. The four main explanations include: 1. Awareness and recognition: There has been an increased awareness and recognition of ADHD over the past few decades, resulting in more people seeking diagnosis and treatment.

2. Changes in diagnostic criteria: The diagnostic criteria for ADHD has changed over time, which may have contributed to an increase in diagnosis rates.

3. Environmental factors: Some studies suggest that environmental factors, such as exposure to toxins or a high-sugar diet, may contribute to ADHD.

4. Overdiagnosis: There is concern that ADHD is being overdiagnosed and that some children may be receiving a diagnosis without a thorough evaluation. This may contribute to the increase in diagnosis rates.

The main explanations for the increase in ADHD from 1990 to the present are:
Increased awareness and better diagnostic methods: Over time, there has been a greater understanding of ADHD, its symptoms, and the diagnostic process. This has led to more people being diagnosed who may have been previously overlooked. Changes in diagnostic criteria: The criteria for diagnosing ADHD have evolved, with revisions to the DSM (Diagnostic and Statistical Manual of Mental Disorders) making it easier to identify and diagnose the condition. Societal factors: Modern lifestyles, including increased screen time, less physical activity, and a faster pace of life, may contribute to ADHD symptoms and diagnosis rates.

To know more about ADHD visit:

https://brainly.com/question/13719580

#SPJ11

When walking across a floor the force of friction depends on how big my foot ishow fast I am walkingthe type of surface I am working on

Answers

When walking across a floor, the force of friction depends on the type of surface I am walking on.

The force of friction is the force that opposes motion between two surfaces that are in contact. It is caused by the microscopic irregularities of the two surfaces that interlock with each other. The force of friction depends on several factors, including the type of surface, the roughness of the surfaces, and the force pressing the two surfaces together. The force of friction does not depend on the size of the foot or the speed of walking. For example, walking on a cahttps://brainly.com/question/13000653rpeted surface will produce more friction than walking on a smooth, polished floor. In general, rougher surfaces produce more friction than smoother surfaces, and greater force pressing the two surfaces together produces more friction.

To learn more about friction:

https://brainly.com/question/13000653

#SPJ11

the crankshaft in a race car goes from rest to 3000 rpm in 2.0s. what is the crankshaft's angular acceleration? (in rad/s2.) assume uniform angular acceleration.

Answers

To find the angular acceleration of the crankshaft, we can use the equation: angular acceleration (α) = change in angular velocity (ω) / time taken (t). We are given that the crankshaft goes from rest (ω=0) to 3000 rpm (ω=3000 rpm = 314.16 rad/s) in 2.0 seconds.

So, the change in angular velocity is:

ω - 0 = 314.16 rad/s - 0 = 314.16 rad/s

And the time taken is:

t = 2.0 s

Now, we can plug these values into the equation:

α = (314.16 rad/s - 0) / 2.0 s = 157.08 rad/s2

Therefore, the angular acceleration of the crankshaft in the race car is 157.08 rad/s2.

To find the crankshaft's angular acceleration in a race car that goes from rest to 3,000 RPM in 2.0 seconds, we can follow these steps:

Step 1: Convert RPM to rad/s
1 RPM = 2π rad/min, so we need to convert RPM to rad/s.

Step 2: Apply the formula for angular acceleration
We'll use the formula: ω_f = ω_i + α*t, where ω_f is the final angular velocity, ω_i is the initial angular velocity, α is the angular acceleration, and t is time. Since the crankshaft starts from rest, ω_i = 0.

Step 3: Solve for angular acceleration (α)

Therefore, the angular acceleration of the crankshaft in the race car is 157.08 rad/s2.

To know more about crankshaft visit:

https://brainly.com/question/29694018

#SPJ11



Current is a measure of: A.force that moves a charge past a point B.resistance to the movement of a charge past a point C.energy used to move a charge past a point D.amount of charge that moves past a point per unit time E.speed with which a charge moves past a point

Answers

D. Amount of charge that moves past a point per unit time. Current is measured in amperes (A) and is defined as the amount of charge that moves past a point per unit time. It is the rate of flow of electric charge through a conductor.

What is amperes?

Amperes (amps, or A) is the unit of electrical current in the International System of Units (SI). It is a measure of the rate of flow of electrons through a wire or other electrical conductor, and is named after the French physicist André-Marie Ampère. It is the basic unit of electric current in SI and is defined as the amount of current that will produce a force of one newton per meter of length between two parallel conductors of infinite length and negligible cross-sectional area.

To learn more about amperes
https://brainly.com/question/29658586
#SPJ4

when a dvd is read, laser light touches the dvd surface and is then measured at location a. what allows light to return to location a after striking the dvd surface?

Answers

When a DVD is read, laser light is directed onto the surface of the DVD at location a. This light reflects off the surface of the DVD and is then measured by a sensor, which detects changes in the intensity of the reflected light. The surface of the DVD is coated with a reflective layer that allows the laser light to bounce back to location a after striking the surface. This reflective layer is made up of tiny metallic particles that reflect the laser light back to the sensor. As the laser light moves across the surface of the DVD, it reads the data stored on the surface by detecting changes in the reflection of the laser light.
 When a DVD is read, laser light is emitted from a source and directed towards the DVD surface. The laser light then strikes the surface, which has microscopic bumps and flat areas representing digital data. These bumps and flat areas are arranged in a spiral pattern.

The laser light reflects off the DVD surface, with the bumps and flat areas causing slight variations in the reflected light. These variations represent the digital data encoded on the DVD. A photodetector located at location A measures the reflected light and translates the variations into digital signals that can be processed and interpreted by the DVD player.

In summary, when a DVD is read:
1. Laser light is emitted towards the DVD surface.
2. The light strikes the surface, encountering bumps and flat areas that represent digital data.
3. The laser light reflects off the surface, with the bumps and flat areas causing variations in the reflected light.
4. The reflected light returns to location A, where a photodetector measures the variations and translates them into digital signals.

To know more about  sensor visit:

brainly.com/question/40574124

#SPJ11

Calculate the kinetic energy when: Mass = 15 kg Velocity = 20 m/s

Answers

Answer:

3000 J

Explanation:

Given,

Mass ( m ) = 15 kg

Velocity ( v ) = 20 m/s

To find : Kinetic Energy ( K.E )

Formula

K.E = mv²/2

K.E = 15 × 20²/2

= 15 × 20 × 20/2

= 15 × 20 × 10

K.E = 3000 J

Note

J is Joule.

Joule is the unit of Kinetic Energy.

The two rigid objects shown in the figure below have the same mass, radius, and angular speed. If the same braking torque is applied to each, which takes longer to stop?.

Answers

The object with a larger radius takes longer to stop, even if both objects have the same mass and angular speed. This is because the braking torque is applied at the same angular acceleration, but the larger radius means that the object has a larger linear velocity, and therefore more kinetic energy. The larger kinetic energy means that more work needs to be done to stop the object, resulting in a longer stopping time.
Hi! Based on the provided information, both rigid objects have the same mass, radius, and angular speed. When the same braking torque is applied to each object, they will both take the same amount of time to stop. This is because the braking torque will decelerate them at the same rate due to their identical properties, eventually bringing them to a halt.

To know more about angular acceleration visit:

brainly.com/question/29428475

#SPJ11

when attempting to stop a car quickly on dry pavement, which of the following methods will stop thecar in the least time? (a) slam on the brakes as hard as possible, locking the wheels and skidding to a stop. (b)press the brakes as hard as possible without locking the wheels and rolling to a stop. explain.'

Answers

Pressing brakes without locking wheels stops car in least time on dry pavement.

What method will stop a car in the least amount of time on dry pavement?

Pressing the brakes as hard as possible without locking the wheels and rolling to a stop will stop the car in the least amount of time. This is because when you slam on the brakes and lock the wheels, the tires lose their grip on the road and start skidding, which increases the distance required to bring the car to a stop.

On the other hand, when you press the brakes as hard as possible without locking the wheels, the tires maintain their grip on the road, allowing the car to slow down more quickly. This method is also safer because it allows the driver to maintain control of the vehicle and steer around any obstacles that may be in the way.

In summary, it's important to remember that slamming on the brakes and locking the wheels may seem like the quickest way to stop a car, but it actually increases the stopping distance and presents a greater risk of losing control of the vehicle. Pressing the brakes as hard as possible without locking the wheels is the safest and most effective way to bring a car to a quick stop on dry pavement.

To learn more about brakes, visit: https://brainly.com/question/29671080

#SPJ4

determine the current flow in a 480-volt, 3-phase, 10-horsepower motor circuit after the circuit has been corrected to 100% power factor.

Answers

After the circuit has been corrected to 100% power factor, the current flow in the 480-volt, 3-phase, 10-horsepower motor circuit would be 13.3 amps.

To determine the current flow in a 480-volt, 3-phase, 10-horsepower motor circuit after the circuit has been corrected to 100% power factor, you will need to use the formula:

I = (P x 746)/(E x PF x √(3))

Where I is the current in amps, P is the power in horsepower, E is the voltage in volts, PF is the power factor, and √(3) is the square root of 3 (1.732).

Assuming the circuit was operating at a lagging power factor before correction, let's say the original power factor was 0.8. We can now calculate the current flow after correction to 100% power factor:

I = (10 x 746)/(480 x 1 x 1.732 x 0.8) = 13.3 amps

Therefore, after the circuit has been corrected to 100% power factor, the current flow in the 480-volt, 3-phase, 10-horsepower motor circuit would be 13.3 amps.

Learn more about circuit here,

https://brainly.com/question/17684987

#SPJ11

A hollow sphere and a hollow cylinder of the same radius and mass roll up an incline without slipping and have the same initial center of mass velocity. Which object reaches a greater height before stopping?

Answers

The hollow sphere will reach a greater height before stopping than the hollow cylinder. This is because a sphere has a greater moment of inertia than a cylinder of the same mass and radius.

What is sphere?

A sphere is a three-dimensional shape that is perfectly round, like a ball. It is the shape of a completely round object in which all points on the surface are equally far from the center. A sphere is the three-dimensional version of a circle, which is two-dimensional. A sphere has no edges, corners, or flat surfaces. It is one of the most symmetrical and perfect shapes in nature, and can be seen in many objects, including planets, bubbles, and even some fruits and vegetables.

Moment of inertia is the rotational inertia of an object, or the resistance of an object to angular acceleration. The greater the moment of inertia, the more energy is required to rotate the object, and the more energy the object will conserve while rolling. This means that the sphere will conserve more energy while rolling up the incline and will reach a greater height before stopping.

To learn more about sphere

https://brainly.com/question/28365362

#SPJ4

56) A 3.9-L volume of ideal neon gas (monatomic) is at a pressure of 5.6 aym and a temperature of The atomic mass of neon is The temperature of the gas is now increased to 430 K and the volume is increased to What is the final pressure of the gas?
A) 4.8 atm
B) 4.3 atm
C) 5.3 atm
D) 5.8 atm
E) 6.3 atm

Answers

The temperature of the gas is now increased to 430 K and the volume is increased to 4.8 atm  is the final pressure of the gas.

Option A is correct .

Joined gas regulation is the mix of Boyle's regulation, Charles' regulation and Gay-Lussac's regulation. The equation for combined gases is,

                      P₁V₁ / T₁ = P₂V₂/ T₂

P₁ =  initial pressure of gas = 5.6 atm

P₂ = final pressure of gas = ?

V₁ = initial volume of gas = 3.9 L

V₂ = final volume of gas = 5.9 L

T₁ = initial temperature of gas = 330 K

T₂ = final temperature of gas = 430 K

Putting all the values in the equation we get ,

                      5.6 × 3.9 / 330 = P₂ × 5.9 / 430

                         P₂ = 4.8 atm

 The final pressure of the gas is 4.8 atm

Final pressure :

After reattachment, the final pressure is usually the one that can be calculated using inviscid theory, but in some cases, the pressure goes above the inviscid value.

Initial temperature :

The average temperature of the contents of the coldest container to be processed at the beginning of the thermal processing cycle is referred to as the initial temperature. This temperature is determined after the filled and sealed container has been thoroughly stirred or shaken.

Learn more about initial temperature :    

brainly.com/question/29943911    

#SPJ4  

g a playground merry-go-round has a mass of 120 kg and a radius of 1.80 m and it is rotating with an angular velocity of 0.500 rev/s. what is its angular velocity (in rev/s) after a 18.0 kg child gets onto it by grabbing its outer edge? the child is initially at rest.

Answers

The angular velocity of the merry-go-round after the 18.0 kg child gets on it by grabbing its outer edge is [tex]0.456 rev/s.[/tex]

What is angular velocity ?

Angular velocity is the rate at which an object rotates or revolves around a point. It is measured in radians per second (rad/s) or in revolutions per minute (rpm). Angular velocity is closely related to linear velocity, which is the rate at which an object moves in a straight line. The angular velocity of an object is the magnitude of its angular momentum, which is the product of its moment of inertia and angular velocity. Angular velocity is usually represented by the symbol ω (omega).

We can calculate the new angular velocity of the merry-go-round after the 18.0 kg child gets on it by using the conservation of angular momentum. Angular momentum is defined as the product of moment of inertia and angular velocity.

Moment of inertia = [tex]mr^{2}[/tex]

Initial angular momentum =[tex](120 kg)(1.80 m)^2(0.500 rev/s)[/tex]

Final angular momentum = [tex](138 kg)(1.80 m)^2[/tex]ω

Since the final angular momentum is equal to the initial angular momentum, we can set the two equations equal to each other and solve for ω.[tex](120 kg)(1.80 m)^2(0.500 rev/s)[/tex]= [tex](138 kg)(1.80 m)^2[/tex]ω

ω = [tex]0.456 rev/s[/tex]

To learn more about angular velocity

https://brainly.com/question/29342095

#SPJ4

A person makes a cup of coffee by first placing a 200 W electric immersion heater in 0. 32 kg

of water. How much heat must be added to the water to raise its temperature from 20°C to

80°C?

Answers

A person makes a cup of coffee by first placing a 200 W electric immersion heater in 0. 32 kg of water,  it would take approximately 400 seconds or 6 minutes and 40 seconds to raise the temperature of 0.32 kg of water from 20°C to 80°C using a 200 W electric immersion heater.

The heat required to raise the temperature of a substance can be calculated using the following formula

Q = mcΔT

Where Q is the heat added or removed, m is the mass of the substance, c is the specific heat capacity of the substance, and ΔT is the change in temperature.

In this case, the mass of water is 0.32 kg, the initial temperature is 20°C, and the final temperature is 80°C. The specific heat capacity of water is 4.18 J/g°C or 4180 J/kg°C.

First, we need to calculate the temperature change

ΔT = final temperature - initial temperature = 80°C - 20°C = 60°C

Next, we can calculate the heat required

Q = mcΔT = (0.32 kg)(4180 J/kg°C)(60°C) = 79872 J

Since the electric immersion heater is rated at 200 W, we can calculate the time required to add this amount of heat

t = Q/P = 79872 J / 200 W = 399.36 s

Therefore, it would take approximately 400 seconds or 6 minutes and 40 seconds to raise the temperature of 0.32 kg of water from 20°C to 80°C using a 200 W electric immersion heater.

To know more about electric immersion heater here

https://brainly.com/question/13607492

#SPJ4

Suppose an electron was bound to a proton, as in the hydrogen atom, but by the gravitational force rather than by the electric force.Part AWhat would be the radius of the first Bohr orbit?Part BWhat would be energy of the first Bohr orbit?

Answers

Part A: The radius of the first Bohr orbit in gravitational constant would be equal to which is given by [tex]$2GM/c^2$[/tex]. Part B: The energy of the first Bohr orbit would be given by the energy of a particle in a circular orbit.

What is gravitational constant?

The Gravitational Constant, denoted by the letter G, is a fundamental physical constant appearing in Newton’s law of universal gravitation. It is an universal constant of proportionality that appears on the right side of the equation F = Gm¹m²/r² and represents the strength of the gravitational force between two objects with masses m₁ and m₁ separated by a distance r. G has a value of 6.67 x 10-11 m3 kg-1 s-2, and it is the same regardless of the masses or separation of two objects in the universe.

Part A: The radius of the first Bohr orbit would be approximately equal to the Schwarzschild radius of the proton,, which is given by [tex]$2GM/c^2$[/tex], where [tex]$G$[/tex] is the gravitational constant, [tex]$M$[/tex] is the mass of the proton and [tex]$c$[/tex] is the speed of light.

Part B: The energy of the first Bohr orbit would be given by the energy of a particle in a circular orbit around a massive object, which is given by [tex]$GMm/2r$[/tex], where [tex]$m$[/tex] is the mass of the electron and [tex]$r$[/tex] is the radius of the orbit. Substituting in the radius of the first Bohr orbit from Part A would give us the energy of the first Bohr orbit.

To learn more about gravitational constant
https://brainly.com/question/31200255
#SPJ4

4An electric heater is operated by applying a potential difference of 50.0 V across a wire of total resistance 8.00 Ω. Find the current in the wire and the power rating of the heater.5.What would the current in the heater in Problem 4 be if the wire devel- oped a short and the resistance was reduced to 0.100 Ω?

Answers

If the resistance of the wire is reduced to 0.100 Ω, the current in the electric heater would be 625 A.

Using Ohm's law, we can calculate the current in the wire: I = V/R = 50.0 V / 8.00 Ω = 6.25 A. To find the power rating of the heater, we can use the formula P = VI, where V is the voltage and I is the current. Therefore, P = (50.0 V)(6.25 A) = 312.5 W. When the resistance is reduced to 0.100 Ω, the current can be calculated as I = V/R = 50.0 V / 0.100 Ω = 625 A. This is a significant increase in current compared to the previous situation, which could cause overheating and potential damage to the heater or other components of the electric system. It is important to ensure that electrical circuits are designed to handle the expected current and voltage to prevent safety hazards.

To learn more about resistance, click here:
https://brainly.com/question/30799966

#SPJ11

Consider a distant galaxy located directly behind a cluster of galaxies, as shown in this interactive figure. As seen from earth, the gravitationally lensed images of the distant galaxy will appear more widely separated if the intervening cluster of galaxies has __________.

Answers

If the intervening cluster of galaxies has a larger mass, the gravitationally lensed images of the distant galaxy will appear more widely separated when seen from Earth.

Gravitational lensing occurs when the path of light from a distant object is bent by the gravitational field of an intervening object, such as a galaxy or a cluster of galaxies. The amount of bending depends on the mass of the intervening object. A more massive object will bend light more than a less massive object.

In this case, the distant galaxy is located behind a cluster of galaxies, and its light passes through the cluster's gravitational field before reaching Earth. If the cluster has a larger mass, it will bend the light more, resulting in a greater separation between the gravitationally lensed images of the distant galaxy when seen from Earth.

To learn more about galaxy visit:

brainly.com/question/31361315

#SPJ11

Other Questions
Nonfinancial information that management might evaluate in making a decision would not include. Devic's disease involves autoantibodies against: So, summarize the two important ways cardiac myocyte relaxation is accomplished. glycerol-3-phosphate is a precursor for the biosynthesis of triacylglycerol. what is the origin of glycerol-3-phosphate? What is the temperature used for the extension step?A. 60 CB. 94 CC. 72 C What planet is the observatory telescope viewing in bloxburg?. a widely used "short-wave" radio broadcast band is referred to as the 31-m band. what is the frequency of a 31-m radio signal? total assets, total liabilities, and total stockholders' equity do not change as a result of a large stock dividend.T/F Demand for outboard motors depends on consumers purchasing fishing boats Depolarizing local potentials are caused by an influx of:. In what ways do plants benefit an ecosystem? A. Plants serve as a food source for other organisms. B. Plants make and preserve soil. C. Plants produce oxygen through the process of photosynthesis. D. All of these. The innermost layer of the digestive tract insulates it from powerful enzymes and secretes digestive juices. It is known as the X If Given Manometry Readings for UE, ME, LES, which diseases give what readings? following the decision by major trucking companies to use self-driving trucks, most truck drivers lost their jobs. is an example of based on the study of patient h.m., it has been concluded that the hippocampus is a. where immediate memories are stored. b. not required for retrieval of long-term memories. c. where long-term memories are stored. d. the location of short-term memory. e. the area of the brain that causes severe retrograde amnesia when damaged. reaching agreement on several small issues is known as which of the following?A. contradictionB. agreementC. stackingD. refinementE. persuasion Which statement best describes the direction of heat flow by conduction between two samples of the same material?. Calculate the depth in the ocean at which the pressure is three times atmospheric pressure. Atmospheric pressure is 1. 013 105 pa. The acceleration of gravity is 9. 81 m/s 2 and the density of sea water is 1025 kg/m3. Answer in units of m. a hypothetical element x has 3 naturally occurring isotopes; x-40, x-41 and x-42. their abundances are 72.0%, 9.00%, and 19.0% respectively. what is the atomic mass of x? cosmetics firm satinsilk is revamping its mission statement and advertising strategy. the ceo stresses that the new mission statement should be market-oriented rather than product-oriented. which of the following mission statements will best suit the company?