6. Drivers in two identical cars make maximum deceleration stops from speeds of 50 km/h and 100 km/h. How do the stopping distances compare? A. Equal. B. The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. C. The stopping distance from 100 km/h is 4 times as long as the stopping distance from 50 km/h.

Answers

Answer 1

The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. This is the best option. The correct option is B.

The stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h. It is the rate at which an object decreases speed. When you apply the brakes to your car, you are effectively causing it to decelerate. The acceleration and deceleration rates are the same, with one important difference: acceleration increases the speed of an object, while deceleration reduces it.

Factors that influence stopping distance include the reaction time of the driver and the state of the road surface. At 50 km/h and 100 km/h, drivers in two identical cars perform maximum deceleration stops. According to the formula, the stopping distance is proportional to the square of the velocity. That is, if the speed of the car is doubled, the stopping distance is quadrupled, and if the speed is halved, the stopping distance is decreased by a factor of four.

As a result, the stopping distance is proportional to the square of the velocity. The stopping distance is proportional to the square of the velocity: {stopping distance}∝{velocity²}. As a result, the stopping distance of a car traveling at 100 km/h is 4 times that of a car traveling at 50 km/h.

2² = 4.

Therefore, the stopping distance from 100 km/h is 2 times as long as the stopping distance from 50 km/h.

To learn more about acceleration:

https://brainly.com/question/460763

#SPJ11


Related Questions

dry soil. The volume of this sample is 400 cm3. At field capacity the soil held 100 grams of water. The total volume of solid particles in this soil was 180 cm3. Calculate the following properties for this soil. 1. Bulk density in g/cm3= 2. Particle density in g/cm3= 3. Percentage of total porosity using bulk density and particle density values = 4. Percentage of water in the soil at field capacity on a mass basis (see pg 112) = 5. Percentage of water in the soil at field capacity on a volume basis (see pg 112) = 6. Total volume of pores in this soil in cm3= 7. Total volume of water in the pores at field capacity in cm3= 8. Percentage of the total pore space filled with water at field capacity = 9. Total volume of air spaces in this soil at field capacity in cm3= 10. Percentage of the total pore space filled with air at field capacity = As a general rule, a normal soil near field capacity will contain approximately 50% water and 50 % air in the total pore space of the soil (half water and half soil). 11. How does this rule agree with the data from the previous calculation?

Answers

The calculated data aligns with the general rule that a normal soil near field capacity contains approximately 50% water and 50% air in the total pore space of the soil.

For the given soil sample, the following properties can be calculated: 1. Bulk density = 0.75 g/cm3, 2. Particle density = 0.45 g/cm3, 3. Percentage of total porosity = 40%, 4. Percentage of water at field capacity (mass basis) = 25%, 5.

Percentage of water at field capacity (volume basis) = 20%, 6. Total volume of pores = 220 cm3, 7. Total volume of water at field capacity = 100 cm3, 8. Percentage of pore space filled with water at field capacity = 45%, 9.

Total volume of air spaces at field capacity = 120 cm3, 10. Percentage of pore space filled with air at field capacity = 55%. The calculated data agrees with the general rule that a soil near field capacity contains approximately 50% water and 50% air in the total pore space of the soil.

Bulk density is calculated by dividing the mass of dry soil by its volume, which gives a value of 0.75 g/cm3.

Particle density is calculated by dividing the mass of solid particles by their volume, resulting in a value of 0.45 g/cm3.

Percentage of total porosity is obtained by subtracting the particle density from the bulk density, dividing the result by the bulk density, and multiplying by 100, resulting in 40%.

Percentage of water in the soil at field capacity (mass basis) is calculated by dividing the mass of water by the mass of dry soil, which gives 25%.

Percentage of water in the soil at field capacity (volume basis) is obtained by dividing the volume of water by the total volume of soil, resulting in 20%.

Total volume of pores is calculated by subtracting the volume of solid particles from the total volume of soil, resulting in 220 cm3.

Total volume of water in the pores at field capacity is given as 100 cm3.

Percentage of the total pore space filled with water at field capacity is calculated by dividing the volume of water by the total volume of pores and multiplying by 100, resulting in 45%.

Total volume of air spaces at field capacity is obtained by subtracting the volume of water from the total volume of pores, resulting in 120 cm3.

Percentage of the total pore space filled with air at field capacity is calculated by dividing the volume of air by the total volume of pores and multiplying by 100, resulting in 55%.

The calculated data aligns with the general rule that a normal soil near field capacity contains approximately 50% water and 50% air in the total pore space of the soil, as the percentages obtained for water and air are close to this expected distribution.

Learn more about field capacity from the given link:

https://brainly.com/question/30766172

#SPJ11


If
the normal law of the Airbus A320 is active, can the pilot override
the high-speed protection?

Answers

No, the pilot cannot override the high-speed protection system when the normal law of the Airbus A320 is active.

The normal law is one of the control laws implemented in the fly-by-wire system of the aircraft. It provides flight envelope protections and limits to ensure the aircraft operates within safe and optimal performance parameters.

The high-speed protection is a feature of the normal law that activates when the aircraft approaches or exceeds its maximum designed speed (VMO/MMO). It limits the aircraft's speed to prevent structural damage and maintain aerodynamic stability. The high-speed protection system automatically adjusts the aircraft's controls to limit the speed.

In this scenario, the pilot cannot override the high-speed protection because it is a critical safety feature designed to prevent the aircraft from exceeding safe operating limits. The normal law ensures that the aircraft operates within its intended performance capabilities and protects it from potential hazards.

to know more about speed visit:

brainly.com/question/29100366

#SPJ11

Light of wavelength 200.0 nm is incident on a metal plate with a threshold wavelength of 400.0 nm. What is the energy of the incident photon in electron volts?
a.
2.48 × 105 eV
b.
0.161 eV
c.
6.20 eV
d.
3.10 eV

Answers

The energy of an incident photon in electron volts (eV) can be calculated using the equation: Therefore, the answer is option c. 6.20 eV.

E = h c /λ Where E is the energy of the incident photon, h is the Planck constant, c is the speed of light, and λ is the wavelength of the incident light.

Here, the wavelength of the incident light is 200.0 nm, which is less than the threshold wavelength of the metal plate (400.0 nm).

This means that the incident light has enough energy to eject electrons from the metal surface, and the metal will undergo the photoelectric effect.

The energy of the incident photon can be calculated as:

E = hc/λ

= (6.626 × 10^-34 J s) × (2.998 × 10^8 m/s) / (200.0 × 10^-9 m)

= 9.93 × 10^-19 J

To convert the energy to electron volts, we can use the conversion factor: 1 eV

= 1.602 × 10^-19 J.

Therefore, the energy of the incident photon in eV is:

E/eV

= (9.93 × 10^-19 J) / (1.602 × 10^-19 J/eV)

≈ 6.20 eV

Therefore, the answer is option c. 6.20 eV.

To know more about photon visit :

https://brainly.com/question/33017722

#SPJ11

I need assistance on questions 5 and 6 5. [0/10 Points] DETAILS PREVIOUS ANSWERS SERCP11 10.4.P.031. 1/5 Submissions Used One mole of oxygen gas is at a pressure of 5.50 atm and a temperature of 25.5°C. (a) If the gas is heated at constant volume until the pressure triples, what is the final temperature? °C (b) If the gas is heated so that both the pressure and volume are doubled, what is the final temperature? PC Need Help? Read It 6. [-/9 Points] DETAILS SERCP11 11.1.P.002. 0/5 Submissions Used A medium-sized banana provides about 105 Calories of energy. HINT (a) Convert 105 Cal to joules. (b) Suppose that amount of energy is transformed into kinetic energy of a 2.13 kg object initially at rest. Calculate the final speed of the object (in m/s). m/s J (c) If that same amount of energy is added to 3.79 kg (about 1 gal) of water at 19.7°C, what is the water's final temperature (in °C)? The specific heat of water is c = 4186 (kg - °C) °C Need Help? Read It

Answers

For part (a), the final temperature is 482.89 K or 209.74°C. For part (b), the final temperature is 819.90 K or 546.75°C. For part (c), the final temperature of the water is 19.728°C.

For question 5, the final temperature when the pressure triples can be determined by using the formula PV = nRT. When the pressure is multiplied by 3, the final temperature can be calculated as

T2 = T1 * (P2 / P1) = 25.5 + 273.15 * (5.5 * 3 / 5.5)

= 482.89 K or 209.74°C.

Similarly, when both the pressure and volume are doubled, the final temperature can be calculated as T2 = T1 * (P2V2 / P1V1) = 25.5 + 273.15 * (2 * 2 / 1) = 819.90 K or 546.75°C.  

For question 6, part (a) is solved by converting 105 Calories to joules by using the conversion factor 1 Cal = 4.184 J. In part (b), the final velocity can be calculated by using the formula for kinetic energy, which is equal to (1/2)mv^2, where m is the mass and v is the velocity.

The final temperature of the water in part (c) can be calculated using the formula Q = mcΔT, where Q is the amount of energy, m is the mass of the water, c is the specific heat capacity, and ΔT is the change in temperature. The final temperature is found to be 19.728°C.

Learn more about specific heat capacity here:

https://brainly.com/question/28302909

#SPJ11

Which type of ignition occurs when a mixture of fuel and oxygen encounter an external heat source with sufficient heat or thermal energy to start the combustion process?
Select one:
a. Primary ignition
b. Kinetic ignition
c. Autoignition
d. Piloted ignition

Answers

The type of ignition that occurs when a mixture of fuel and oxygen encounters an external heat source with sufficient heat or thermal energy to start the combustion process is known as Piloted ignition. The correct answer is option D.

Piloted ignition is a type of ignition that happens when a mixture of fuel and oxygen encounters an external heat source with sufficient heat or thermal energy to start the combustion process. A spark is not needed for this to happen. The external heat source could be a burning cigarette, a spark from an electrical source, or any other heat source that has the ability to produce heat. When a combustible fuel is introduced into a space with air, the mixture becomes flammable when it reaches a certain concentration.

When the fuel-air mixture is heated to a high temperature, the reaction takes place and the fuel ignites. This reaction is piloted ignition. The two other types of ignition are autoignition and kinetic ignition. Autoignition is when a combustible fuel ignites spontaneously due to its high temperature and pressure. It is used in diesel engines. Kinetic ignition is when a high-velocity flame from a spark or other ignition source ignites the fuel. It is used in gasoline engines.

To learn more about ignition:

https://brainly.com/question/31936083

#SPJ11

An atomic nucleus has a diameter of d=2.5×10
−14
m. Heisenberg's uncertainty principle tells us that Δp
x

Δx≥
2
A

. Part 1) What is the minimum uncertainty in the momentum of a particle confined in the nucleus. Δp
e

≥ Part 2) The uncertainty gives an order of magnitude estimate of the momentum of a hypothetical electron confined in the nucleus. For this part assume that the momentum of the electron p
ε

=Δp
ε

. As the mass of the electron is small, relativistic effects are not necessarily negligible. The relativistic momentum is given by: p=
1−
t
2

v
2





mv

. This can be rearranged and written as v=
c
2
m
2
+p
2



cp

. What is the velocity of the electron as a fraction of the speed of light? v
e

= c Part 3) What is the velocity of a neutron confined in the nucleus as a fraction of the speed of light?

Answers

Part 1) The minimum uncertainty in the momentum of a particle confined in the nucleus is calculated by using the formula; Δp ≥ h/2AΔp = (6.626×10⁻³⁴ J.s)/(2×2.5×10⁻¹⁵ m)Δp = 1.33×10⁻¹⁹ kg m/s

Part 2) Given, p_ε = Δp_ε

The relativistic momentum of the electron is given by; P = [(1 - (v/c)^2)^(-0.5)] x mv = [(1 - (v/c)^2)^(-0.5)] x (9.11 x 10^-31 kg)

Let's square both sides of the above equation; p^2 = [(1 - (v/c)^2)^(-1)] x m^2v^2 = [(1 - (v/c)^2)^(-1)] x m^2c^2 - m^2v^2v^2 + m^2v^4/c^2 = m^2c^2 - m^2v^2v^2 + m^2v^4/c^2 + m^2v^2 = m^2c^2v^2/c^2(1 + m^2v^2/c^4) = m^2c^2/v^2v^2 = c^2/(1 + m^2v^2/c^4)

Substitute p_ε = Δp = 1.33×10⁻¹⁹ kg m/sm = 9.11 × 10⁻³¹ kgc = 3.00 × 10⁸ m/st = 1 - (v/c)²t = 1 - (ve/c)²ve = (t)^(1/2)c∴ v_ε = ve = c (as t is very close to 1)

Part 3) As a neutron is much more massive than an electron, relativistic effects on a neutron are negligible compared to the electron.

Therefore, the velocity of a neutron confined in the nucleus as a fraction of the speed of light is 0.

To know more about velocity refer to:

https://brainly.com/question/1844960

#SPJ11

5 Air conditioning 1. Estimate the volume of your house (or apartment) in cubic meters. One quick way of doing this is to multiply the square footage by the ceiling height. (If you don't know the square footage of your house you can use my apartment which is 1000ft2 with an 8ft ceiling. However, it will probably be more fun to do with your own house.) Give the answer in cubic meters. 2. The specific heat of dry air is c = 1.0%. The density of air is pa 1.2 h. How much energy must your air conditioner remove from the air in your house to cool it from 30°C to 20°C assuming your house is filled with dry air? gº

Answers

The volume of the apartment in cubic meters is 226.56 m³. The energy required by the air conditioner to cool the apartment from 30°C to 20°C is 27.187 kJ.

1. To estimate the volume of the house, we need to find the product of the square footage of the house by the ceiling height. The square footage of the apartment is given to be 1000ft² with an 8ft ceiling.

Therefore, the volume of the apartment can be calculated as follows; Volume = Area x height

Where Area = 1000 ft² Height = 8 ft Volume = 1000 ft² x 8 ft = 8000 ft³

The volume of the apartment is 8000 cubic feet.

To convert cubic feet to cubic meters, we use the conversion factor, 1 ft³ = 0.02832 m³.

Therefore, the volume of the apartment in cubic meters is; 8000 ft³ x 0.02832 m³/ft³ = 226.56 m³

2. The heat energy required to cool the house from 30°C to 20°C can be calculated using the formula, Q = mcΔT.

Where; Q = Heat energy required m = Mass of the air c = Specific heat capacity of dry air ΔT = Change in temperature of the air

The mass of air can be calculated using the formula, mass = density x volume.

Therefore, the mass of air in the apartment is; m = p x V = 1.2 kg/m³ x 226.56 m³ = 271.87 kg

The specific heat capacity of dry air is given as, c = 1.0%.

We can convert this to SI units by dividing by 100.

Therefore, c = 1.0/100 = 0.01 kJ/kg K

Substitute these values into the heat energy formula to obtain; Q = mcΔTQ = 271.87 kg x 0.01 kJ/kg K x (30 - 20)°CQ = 27.187 kJ

The energy required by the air conditioner to cool the apartment from 30°C to 20°C is 27.187 kJ.

To know more about density refer to:

https://brainly.com/question/13692379

#SPJ11

A generator with no-load frequency of 51.0 Hz and a slope (Sp) of Y MW/Hz is connected to the Load 1 (Y MW and 0.8 PF lagging) and Load 2 (0.75Y MVA and 0.75 PF lagging) through transmission line (Zline = j 1 Ohm). If the voltage at load side is kept constant of 1000 Z0® Volt, Calculate !

Scenario 1: The generator is directly connected to the Loads
G Zline = j1 ohm Load 1 1 MW 0.8 Lagging Load 2 0,8 MVA 0,8 lagging VLoad = 1000/0° V

a. Find the operating frequency of the system before the switch (load 2) is closed.
b. Find the operating frequency of the system after the switch (load 2) is closed.
c. What action could an operator take to restore the system frequency to 50 Hz after both loads are connected to the generator?

Scenario 2: The generator is connected to the Loads through Transformer
1:10 10:1 VLoad = 1000Z0° V Load 1 1 MW G Zline =j1 ohm 0.8 Lagging Load 2 0,8 MVA 0,8 lagging

a. Find the operating frequency of the system before the switch (load 2) is closed.
b. Find the operating frequency of the system after the switch (load 2) is closed.
c. What action could an operator take to restore the system frequency to 50 Hz after both loads are connected to the generator?

Answers

Scenario 1:

a. The operating frequency of the system before the switch (load 2) is closed is approximately 50.2 Hz.

b. The operating frequency of the system after the switch (load 2) is closed remains approximately 50.2 Hz.

c. Increase the mechanical input power to the generator and Decrease the loads

Scenario 2:

a. The operating frequency of the system before the switch (load 2) is closed is approximately 50.2 Hz.

b. The operating frequency of the system after the switch (load 2) is closed remains approximately 50.2 Hz.

c. Increase the mechanical input power to the generator and Decrease the loads.

Scenario 1: Generator directly connected to the loads

a. To find the operating frequency of the system before the switch (load 2) is closed, we need to consider the power balance equation:

Total power supplied by the generator = Power consumed by Load 1 + Power consumed by Load 2

The total power supplied by the generator can be calculated using the formula:

Total power = No-load frequency (f0) * Slope (Sp)

Total power = 51.0 Hz * Y MW/Hz = 51Y MW

The power consumed by Load 1 can be calculated using the formula:

Power consumed by Load 1 = Load 1 (Y MW) * Power factor (0.8 lagging)

Power consumed by Load 1 = Y MW * 0.8 = 0.8Y MW

To find the power consumed by Load 2, we'll convert it to apparent power since we're given the power factor in terms of lagging.

Apparent power consumed by Load 2 = Load 2 (0.8 MVA) * Power factor (0.8 lagging)

Apparent power consumed by Load 2 = 0.8 MVA * 0.8 = 0.64 MVA

To convert the apparent power to real power, we'll use the formula:

Real power consumed by Load 2 = Apparent power * Power factor

Real power consumed by Load 2 = 0.64 MVA * 0.8 = 0.512 MW

Now, we can set up the power balance equation:

51Y MW = 0.8Y MW + 0.512 MW

Simplifying the equation:

50.2Y MW = 0.512 MW

Y ≈ 0.0102 MW

Therefore, the operating frequency of the system before the switch (load 2) is closed is approximately 50.2 Hz.

b. After the switch (load 2) is closed, the total power consumed by the system will increase to Y MW + 0.512 MW.

The new power balance equation will be:

51Y MW = 0.8Y MW + 0.512 MW

Simplifying the equation:

50.2Y MW = 0.512 MW

Y ≈ 0.0102 MW

The operating frequency of the system after the switch (load 2) is closed remains approximately 50.2 Hz.

c. To restore the system frequency to 50 Hz after both loads are connected to the generator, the operator can take the following action:

1. Increase the mechanical input power to the generator: By increasing the mechanical input power, the generator will produce more electrical power and help restore the system frequency to 50 Hz.

2. Decrease the loads: If the loads can be reduced, the total power consumed by the system will decrease, which will help bring the frequency back to 50 Hz.

Scenario 2: Generator connected to the loads through a transformer

a. Before the switch (load 2) is closed, the operating frequency of the system can be calculated using the same power balance equation as in Scenario 1:

Total power = No-load frequency (f0) * Slope (Sp)

Total power = 51.0 Hz * Y MW/Hz = 51Y MW

Power consumed by Load 1 = Y MW * 0.8 = 0.8Y MW

Real power consumed by Load 2 = 0.8 MVA * 0.8 = 0.64 MVA *

0.8 = 0.512 MW

Setting up the power balance equation:

51Y MW = 0.8Y MW + 0.512 MW

Simplifying the equation:

50.2Y MW = 0.512 MW

Y ≈ 0.0102 MW

Therefore, the operating frequency of the system before the switch (load 2) is closed is approximately 50.2 Hz.

b. After the switch (load 2) is closed, the total power consumed by the system will increase to Y MW + 0.512 MW.

The new power balance equation will be:

51Y MW = 0.8Y MW + 0.512 MW

Simplifying the equation:

50.2Y MW = 0.512 MW

Y ≈ 0.0102 MW

The operating frequency of the system after the switch (load 2) is closed remains approximately 50.2 Hz.

c. To restore the system frequency to 50 Hz after both loads are connected to the generator, the operator can take the same actions mentioned in Scenario 1:

1. Increase the mechanical input power to the generator.

2. Decrease the loads.

These actions will help bring the frequency back to the desired 50 Hz.

Learn more about generator from:

https://brainly.com/question/12950635

#SPJ11

Predator UAV has a wing span of 14.85m, a maximum mass of 1020kg, and a fuel mass of 295kg. The power plant is a Rotax four-cylinder, four-stroke engine with a specific fuel consumption of 0.4kg of fuel per kW per hour, driving a two-blade variable-pitch pusher propeller with an efficiency of 0.8. The aircraft drag polar and Oswald efficiency factor can be assumed Cp = 0.03 +0.0236C2 and 0.7, respectively. Ignore the fuel for takeoff, landing, climb and descent. (a) Calculate the wing reference area of the aircraft. (b) Calculate the aircraft maximum range and endurance at a pressure altitude of 20,800ft and a temperature of -15°C.

Answers

In a mass-spring system with mass M and spring constant K, the natural frequency is given by the formula:   f=12π⋅Mk. If the mass of the system increases, the frequency decreases and vice versa. A mass of 680kg is added to M, the natural frequency changes from 5.5Hz to 4.5Hz. The change in frequency of the system, Δf, is given by:

Δf=f1−f2

=12π⋅M+kM1−12π⋅M+ k(M+680)  ​

Here,

f1=5.5Hz,

f2=4.5Hz,

M+ k=12π⋅5.5 and

(M+680)+k=12π⋅4.5

Δf=12π⋅M+ k(M+680)​−12π⋅M+ k​

=−12π⋅680M+k​

680=−12π⋅680M+k

​M+ k=−12π⋅680680  ​

=4.6kg

Now, when the mass is replaced by 1000kg, the total mass of the system becomes M+1000kg.

The new natural frequency, f3 is given by:

f3=12π⋅(M+1000)k  ​Substituting

M+k=4.6kg,

we get:

f3=12π⋅(4.6+1000)

k​ =12π⋅1004.6

k​ = 8.2 Hz (approx).

The new natural frequency is 8.2 Hz.

To know more about mass visit:

https://brainly.com/question/11954533

#SPJ11




A certain radioisotope has a half-life of 11.1 days. What percentage of an initial sample of this isotope remains after 33 days? Number Units

Answers

Approximately 12.5% of the initial sample of the radioisotope remains after 33 days.

The half-life of a radioisotope is the time it takes for half of the initial quantity to decay. In this case, the half-life of the radioisotope is 11.1 days. To determine the percentage of the initial sample that remains after 33 days, we need to consider how many half-lives have elapsed.

Since the half-life is 11.1 days, after 11.1 days, half of the sample will remain. After another 11.1 days (a total of 22.2 days), half of that remaining sample will remain, which is one-fourth of the initial sample. Finally, after another 11.1 days (a total of 33 days), half of the remaining one-fourth will remain, which is one-eighth of the initial sample.

To calculate the percentage, we can divide the amount remaining (one-eighth of the initial sample) by the initial sample and multiply by 100. This gives us (1/8) * 100 = 12.5%.

Therefore, approximately 12.5% of the initial sample of the radioisotope remains after 33 days.

Learn more about: Radioisotope

brainly.com/question/28142049?

#SPJ11

Q3) One end of a steel rod of radius R-9.5 mm and length Z-81 cm is held in a vise. A force of magnitude F-62 KN is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. The elongation AL(in mm) of the rod is: (Young's modulus for steel is 2.0 × 10¹¹ N/m²) a) 0.89 b) 0.61 c) 0.72 d) 0.79 e) 0.58 04) A cylindrical aluminum rod, with an initial length of 0.80 m and radius 1000.0 mm, is clamped in place at one end and then stretched by a machine pulling parallel to its length at its other end. Assuming that the rod's density (mass per unit volume) does not change. The force magnitude (in N) that is required of the machine to decrease the radius to 999.9 mm is: (Young's modulus for aluminum is 7.0 × 10° N/m²) a) 58 b) 44 c) 50 d) 34 e) 64 Q5) To suck lemonade of density 1000 kg/m' up a straw to a maximum height of 4.0 cm. What minimum gauge pressure (in Pascal) must you produce in your lungs? a) 392 b) 588 c) 294 d) 490 Q6) The L-shaped tank shown in the figure is filled with fresh water and is closed at the top. If d = 5.0 m. The (total) force exerted by the water on face A (in 10°N) e) 642 is 34 a) 1.45 b) 2.45 c) 4.23 d) 0.53 e) 5.64

Answers

Elongation of a steel rod The formula for the elongation of a steel rod when a force is applied is given by:

Putting these values in the above formula, [tex]AL = FL / AE= (62 × 10³) / (2.0 × 10¹¹ × 2.8353 × 10⁻⁴)= 0.87 mm[/tex]

So, the elongation of the rod is 0.87 mm (approximately).

A1 = πR1² = π(1000.0 mm)² = 3.14 × 10⁶ mm² = 3.14 m²A2 = πR2² = π(999.9 mm)² = 3.14 × 10⁶ mm² = 3.13996 m²

The change in area is given by,[tex]ΔA = A2 - A1= 3.13996 - 3.14= -0.00004[/tex]m²

The change in length, ΔL = -0.0005 m

Using the above values in the formula for Young's modulus,

[tex]Y = FL / AΔL7.0 × 10¹⁰ N/m² = F / (3.14 m² × (-0.0005 m))F = 44 N[/tex]

Thus, the force required of the machine to decrease the radius of the rod is 44 N.

(b) 44 is the correct answer.

Q5)

P = hρgHere, h = 4.0 cm = 0.04 m Density of lemonade, ρ = 1000 kg/m³

Acceleration due to gravity, g = 9.8 m/s²

Putting these values in the above formula,

[tex]P = hρg= 0.04 × 1000 × 9.8= 3.92 Pa[/tex]

(a) 392 is the correct answer.

Area of face P = hρg= 0.04 × 1000 × 9.8

= 3.92 Pa[tex]P = hρg= 0.04 × 1000 × 9.8= 3.92 Pa[/tex]

Putting these values in the above formula

[tex],F = dghA= 1000 × 9.8 × 5.0 × 24= 1.176 × 10⁶ N = 1.18 × 10⁵ N[/tex]

e) 5.64 is the correct answer.

To know more about steel visit:

https://brainly.com/question/29266446

#SPJ11

3. Find the Thevenin's equivalent circuit with respect to terminals a and b. Draw the Thevenin's equivalent circuit. What value resistor if placed between a and b would draw maximum power from the circuit. How much power would that be?

Answers

The resistor value that should be placed between a and b to draw maximum power is 44 Ω.

The power absorbed by the resistor is 0.23 W.

A Thevenin’s equivalent circuit is a method used for simplifying complex circuits into a single voltage source and a single series resistance. This simplification makes calculations and analysis of the circuit easier and straightforward. A Thevenin’s circuit includes an equivalent voltage source and an equivalent resistance.

To find the Thevenin’s equivalent circuit with respect to terminals a and b, it requires two steps. The first step is to find the equivalent voltage source, while the second step is to find the equivalent resistance. 

Step 1: 

Equivalent Voltage Source:

First, to find the equivalent voltage, remove the resistor between terminals a and b, and measure the voltage between the open circuit.

The voltage obtained between the open circuit is equal to the Thevenin’s equivalent voltage. In the diagram, the Thevenin voltage is equal to the voltage drop across

R4. VTH = V

R4 = 2V 

Step 2: 

Equivalent Resistance:

Next, to find the equivalent resistance, replace all the voltage sources with short circuits and all the current sources with open circuits. 

RTH = R1 + R2 || R3 + R4 

       = 20 + 40 || 60 + 40 

       = 20 + 24 

       = 44 Ω

The Thevenin’s equivalent circuit with respect to terminals a and b is shown below. 

Image Transcription
figure

If a resistance R is placed between the terminals a and b, the power absorbed is maximum when the resistance R is equal to the Thevenin’s equivalent resistance RTH.

Therefore, the maximum power is given by:

Pmax = [(VTH)2/4RTH] 

         = [(2)2/(4*44)] 

         = 0.23 W

Therefore, the resistor value that should be placed between a and b to draw maximum power is 44 Ω.

The power absorbed by the resistor is 0.23 W.

Learn more about resistor value from the given link

https://brainly.com/question/30114938

#SPJ11

Why is the dot product commutative? A. Use the magnitude-direction version of the dot product: à b = |a||| cos(ab) . to explain why it's true that B. Use the Cartesian component version of the dot product: à • b = axbx + ªyby +azbz to explain why it's true that a. b = b. à 2. Which is a unit vector? Which of the following are a unit vector? There is more than one, so test each of them. Carry out any math necessary to explain your answer. Ā A. |A| B. x + y ŷ+2 C. √2 D. ở tỷ tế √√3 à b = b

Answers

|A| is a unit vector, the remaining options (B), (C), and (D) are not unit vectors, as their magnitude is not equal to 1.

The dot product is commutative. There are two ways to explain why the dot product is commutative as follows:

By using the magnitude-direction version of the dot product:

à b = |a||| cos(ab)If we compare two vectors A and B, then the dot product of the two vectors is given as AB = |A||B| cos (θ)And, BA = |B||A| cos (θ)Here, θ is the angle between the two vectors. If we compare the two dot products, then = |A||B| cos (θ)BA = |B||A| cos (θ)We have AB = BAThe dot product of the two vectors is commutative.

By using the Cartesian component version of the dot product:

à • b = ax bx + ªyby +azbzHere, the Cartesian component version of the dot product is given. If we compare the two dot products, then we get a. b = b. àWe have a. b = axbx + ªyby +azbz and, b. a = bxax + byay + bzazWe geta. b = ax bx + ªyby +azbz = bx ax + bay + bzaz = b. a

The dot product of the two vectors is commutative. The magnitude of the vector is the length of the vector. The unit vector has a magnitude of 1. It is a vector that has a length or magnitude of 1.

To know more about magnitude please refer to:

https://brainly.com/question/28714281

#SPJ11

At a certain frequency range sea water has The following parameters Er=72, sigma= 4S/m. a uniform plane EM wave propagates down sea water which is considered as + z direction. at z=0 which is just below the surface, the electric field is E=x100cos(10^(7)pit)(V/m)
A) find the loss tangent and determine in which category that sea water can be approximated: low loss material (yes, no), good conductor (yes, no).
B) find the attenuation factor and the phase constant with units
C) find the wavelength and phase velocity up
D) find the amplitude of the electric field at the following locations (z axis points down)
(x,y,z)=(0,0,1)
(x,y,z)=(1,1,1)
(x,y,z)=(2,2,2)

Answers

A) The loss tangent of the sea water is 0.0556, indicating that it is a low-loss material but not a good conductor.

B) The attenuation factor is 0.004S/m and the phase constant is 10^7 rad/m.

C) The wavelength is 0.628 m and the phase velocity is 1.59x10^6 m/s.

D) The amplitude of the electric field at (0,0,1) is 100 V/m, at (1,1,1) is 70.71 V/m, and at (2,2,2) is 50 V/m.

A) The loss tangent is given by tan(delta) = sigma / (Er × ω × ε₀), where sigma is the conductivity, Er is the relative permittivity, ω is the angular frequency, and ε₀ is the vacuum permittivity. Plugging in the values, we find tan(delta) = 0.0556. This indicates that sea water is a low-loss material but not a good conductor because the loss tangent is small but nonzero.

B) The attenuation factor is given by α = [tex]\sqrt{(\omega \times \mu_0 \times \sigma) / 2x}[/tex] and the phase constant is β = ω × [tex]\sqrt{\mu_0 \times \epsilon_0 \times Er}[/tex], where μ₀ is the vacuum permeability. Substituting the given values, we get α = 0.004 S/m and β = [tex]10^7[/tex] rad/m.

C) The wavelength is given by λ = 2π / β, and the phase velocity is v = ω / β. Plugging in the values, we find λ = 0.628 m and v = [tex]1.59\times10^6[/tex] m/s.

D) The amplitude of the electric field decreases exponentially with distance. At (0,0,1), the amplitude remains at 100 V/m. At (1,1,1), the amplitude reduces to 70.71 V/m, and at (2,2,2), it further decreases to 50 V/m.

To know more about conductor https://brainly.com/question/492289

#SPJ4

Compare batween the VST typical three control techniques ourgut AC line-to-line voltage δ line current waveforms that can supply the three-phase AC indiction motor.

Answers

Three-phase AC induction motors are the most widely used motors in industry, and they are used in a variety of applications. Induction motors are used in various industrial applications, such as paper mills, textile mills, and other industries. In this question, the three control techniques of VST are compared, and the AC line-to-line voltage and line current waveforms that can supply the three-phase AC induction motor are discussed.

Three VST Control Techniques

The VST (Variable-Speed Technology) has three control techniques, which are as follows:

Vector Control:

The vector control technique is the most advanced control method, which provides high accuracy, low torque ripple, and high efficiency in speed control. This technique is used in high-performance drives, which require precise speed control.

Direct Torque Control: The direct torque control technique is used in applications that require a high degree of accuracy, such as textile mills, paper mills, and other industries. This technique provides high accuracy, low torque ripple, and high efficiency in speed control.

Field-Oriented Control: The field-oriented control technique is used in applications that require a high degree of accuracy, such as textile mills, paper mills, and other industries. This technique provides high accuracy, low torque ripple, and high efficiency in speed control.

To know more about induction visit:

https://brainly.com/question/32376115

#SPJ11

10.27 - Rotational Kinetic Energy: Work and Energy Revisited A bus contains a 1410 kg flywheel (a disk that has a 0.600 m radius) and has a total mass of 8,200 kg. Calculate the angular velocity the flywheel must have to contain enough energy to take the bus from rest to a speed of 22.0 m/s, assuming 88.0% of the rotational kinetic energy can be transformed into translational energy. Tries 0/10 How high a hill can the bus climb with this stored energy and still have a speed of 2.90 m/s at the top of the hill? Explicitly show how you follow the steps in the ProblemSolving Strategy for Rotational Energy. Tries 0/10

Answers

A hill can the bus climb with this stored energy and still have a speed of 2.90 m/s at the top of the hill hight is (1/2) * (2.90 m/s)^2 / 9.8 m/s^2.

To calculate the angular velocity of the flywheel, we can follow these steps:

Step 1: Find the total kinetic energy required to accelerate the bus from rest to a speed of 22.0 m/s.

Step 2: Find the rotational kinetic energy of the flywheel that corresponds to 88.0% of the total kinetic energy.

Step 3: Use the formula for rotational kinetic energy to find the angular velocity of the flywheel.

Step 4: Find the height of the hill the bus can climb with the stored energy.

Let's begin with Step 1:

Step 1: Find the total kinetic energy required to accelerate the bus from rest to a speed of 22.0 m/s.

The total mass of the bus is 8,200 kg. To find the total kinetic energy, we use the formula:

Total Kinetic Energy = 0.5 * mass * speed^2

Total Kinetic Energy = 0.5 * 8200 kg * (22.0 m/s)^2

Step 1: Total Kinetic Energy ≈ 4186400 J

Step 2: Find the rotational kinetic energy of the flywheel that corresponds to 88.0% of the total kinetic energy.

Rotational kinetic energy (RKE) can be calculated using the formula:

RKE = (1/2) * moment of inertia * angular velocity^2

The moment of inertia of a disk is (1/2) * mass * radius^2. For the flywheel:

Moment of inertia (I) = (1/2) * 1410 kg * (0.600 m)^2

Now, we can set up an equation to find the angular velocity (ω) that corresponds to 88.0% of the total kinetic energy:

0.88 * Total Kinetic Energy = RKE

0.88 * 4186400 J = (1/2) * (1/2) * 1410 kg * (0.600 m)^2 * ω^2

Step 2: Solve for ω.

ω^2 = (0.88 * 4186400 J) / [(1/2) * (1/2) * 1410 kg * (0.600 m)^2]

Step 2: ω ≈ 30.737 rad/s

Step 3: The angular velocity the flywheel must have is approximately 30.737 rad/s.

Step 4: Find the height of the hill the bus can climb with the stored energy.

The potential energy (PE) gained by the bus as it climbs the hill is converted from the stored energy (kinetic energy) in the flywheel. At the top of the hill, the bus has a speed of 2.90 m/s.

Using the conservation of energy principle, we can set up the equation:

Stored Energy - Energy used to overcome gravitational potential energy = Final kinetic energy

(1/2) * moment of inertia * (angular velocity)^2 - m * g * h = (1/2) * m * (final speed)^2

We want to find the height (h) the bus can climb, so we rearrange the equation:

h = [(1/2) * moment of inertia * (angular velocity)^2 - (1/2) * m * (final speed)^2] / (m * g)

Now we can plug in the values:

h = [(1/2) * (1/2) * 1410 kg * (0.600 m)^2 * (30.737 rad/s)^2 - (1/2) * 8200 kg * (2.90 m/s)^2] / (8200 kg * 9.8 m/s^2)

Step 4: Calculate h.

To learn more about bus

https://brainly.com/question/32119482

#SPJ11




(d) Explain the difference between the "total energy head" and "specific energy head" as applied to open channel flow

Answers

the total energy head accounts for all energy components (elevation, pressure, and velocity) at a given point in the open channel, while the specific energy head represents only the elevation and velocity components relative to the channel bottom.

In open channel flow, the terms "total energy head" and "specific energy head" refer to different concepts related to the energy of the flowing fluid.

1. Total Energy Head:

The total energy head represents the total energy per unit weight of the fluid at a particular point in the open channel. It is the sum of three components: the elevation head, the pressure head, and the velocity head. The elevation head is the potential energy associated with the height of the fluid above a reference plane, the pressure head is the energy due to the pressure of the fluid, and the velocity head is the energy due to the motion of the fluid.

Mathematically, the total energy head (H) can be expressed as:

H = z + (P/γ) + (V²/2g)

where:

- z is the elevation above the reference plane,

- P is the pressure of the fluid,

- γ is the specific weight of the fluid (weight per unit volume),

- V is the velocity of the fluid,

- g is the acceleration due to gravity.

The total energy head is useful for analyzing and describing the energy state of the fluid at a specific point along the flow path in an open channel.

2. Specific Energy Head:

The specific energy head represents the total energy per unit weight of the fluid at a particular point in the open channel, relative to the channel bottom. It is the sum of the elevation head and the velocity head, excluding the pressure head. The specific energy head is often used to analyze the flow characteristics and determine the water surface profile in open channel flow.

Mathematically, the specific energy head (E) can be expressed as:

E = z + (V²/2g)

The specific energy head is particularly important in studying uniform flow conditions, where the flow depth remains constant along a reach of the channel. It helps determine the critical flow conditions and the relationship between flow depth and flow velocity.

In summary, the total energy head accounts for all energy components (elevation, pressure, and velocity) at a given point in the open channel, while the specific energy head represents only the elevation and velocity components relative to the channel bottom. Both concepts play a crucial role in the analysis and understanding of open channel flow.

to know more about acceleration visit:

brainly.com/question/30762941

#SPJ11

A sinusoidal voltage of v(t)=440cos(377t)V is applied across a capacitor of 12μF. Find the instantaneous current drawn by the capacitor and the instantaneous power flow through capacitor. Draw the instantaneous voltage, instantaneous current and instantaneous power

Answers

The instantaneous power flow through the capacitor is -442.25sin(754t) W.

To find the instantaneous current drawn by the capacitor and the instantaneous power flow through the capacitor, we can use the following formulas:

1. Instantaneous current (i(t)) through a capacitor:

  i(t) = C * dV(t)/dt

2. Instantaneous power flow (P(t)) through a capacitor:

  P(t) = i(t) * V(t)

Given:

Voltage across the capacitor, V(t) = 440cos(377t) V

Capacitance, C = 12μF = 12 * [tex]10^{-6[/tex] F

To find the instantaneous current, we need to differentiate the voltage function with respect to time:

dV(t)/dt = -440 * sin(377t) * (377)

Now, we can substitute the values and calculate the instantaneous current:

i(t) = C * dV(t)/dt

    = (12 * [tex]10^{-6[/tex]) * (-440 * sin(377t) * 377)

    = -2008.8 * [tex]10^{-6[/tex] * sin(377t) A

    ≈ -2.0088sin(377t) A

The instantaneous current drawn by the capacitor is approximately -2.0088sin(377t) A

To find the instantaneous power flow, we can multiply the instantaneous current by the voltage:

P(t) = i(t) * V(t)

    = -2.0088sin(377t) * 440cos(377t)

    = -884.51sin(377t)cos(377t)

    = -442.25sin(754t) W

The instantaneous power flow through the capacitor is -442.25sin(754t) W.

To know more about Instantaneous current refer here

https://brainly.com/question/20341821#

#SPJ11

For a negative system g(s)h(s) =1/s(s-2), the nyquist plot:

a. encircles(-1+j0)point once in the coutner clockwise direction
b. does notencircle(-1+j0)
c. encircles (-1+j0) point once in the clockwise direction
d. encircles (-1+j0) point twiece in the counter clockwise direction

Answers

The correct answer is c. The Nyquist plot of the given transfer function encircles the point (-1+j0) once in the clockwise direction.

The given transfer function is g(s)h(s) = 1/(s(s-2)). To determine the Nyquist plot, we need to analyze the behavior of the transfer function in the complex plane.

First, let's consider the poles of the transfer function. The denominator has two poles at s = 0 and s = 2. The pole at s = 0 is a single pole, and the pole at s = 2 is a simple pole.

Since both poles have positive real parts, they contribute to the Nyquist plot by making it move in the clockwise direction. The multiplicity of the pole at s = 0 is 1, which means it will encircle the point (-1+j0) once in the clockwise direction.

Therefore, the correct answer is c. The Nyquist plot of the given transfer function encircles the point (-1+j0) once in the clockwise direction.

In summary, for the negative system g(s)h(s) = 1/s(s-2), the Nyquist plot encircles the point (-1+j0) once in the clockwise direction.

Know more about Nyquist plot here:

https://brainly.com/question/33181363

#SPJ11

Define antenna beamwidth.

Answers

Antenna beamwidth is the angular width of the main beam of an antenna pattern that is defined between the half-power points (3 dB).

The beamwidth is normally determined by evaluating the radiation intensity of the pattern in the azimuthal or elevation plane, and then measuring the angle between the two points where the intensity falls to half-power.

Antenna beamwidth refers to the extent to which an antenna beam spreads out. It is measured in degrees and indicates the angle between the -3 dB points on the power response curve of the antenna. It refers to the angle where the radiated power is half of the power that would be generated if the radiation was uniform across all angles. Antenna beamwidth is a function of antenna size, operating frequency, and the aperture of the antenna.

Learn more about the radiation intensity: https://brainly.com/question/28568553

#SPJ11

copernicus's theories gained widespread scientific acceptance during his lifetime.

Answers

Copernicus's theories, including the heliocentric model of the solar system, gained widespread scientific acceptance during his lifetime. They challenged the prevailing geocentric model and proposed that the Sun is at the center of the solar system.

Nicolaus Copernicus was a Polish astronomer who proposed the heliocentric model of the solar system. His theory stated that the Sun is at the center, and the planets, including Earth, revolve around it. This theory challenged the prevailing geocentric model, which placed the Earth at the center of the universe.

Copernicus's book, 'De Revolutionibus Orbium Coelestium' (On the Revolutions of the Celestial Spheres), published in 1543, presented his heliocentric theory. In this book, he provided mathematical calculations and observations to support his ideas. His work laid the foundation for modern astronomy and had a profound impact on scientific thought.

During Copernicus's lifetime, his theories gained widespread scientific acceptance. However, they also faced opposition from some religious and academic authorities who held onto the geocentric model. Despite the opposition, Copernicus's ideas continued to spread and were further developed and supported by later astronomers, such as Johannes Kepler and Galileo Galilei.

Learn more:

About Copernicus here:

https://brainly.com/question/12712605

#SPJ11

Nicolaus Copernicus (1473-1543) was a Polish astronomer who proposed the heliocentric theory, which posited that the sun, rather than the earth, was the center of the universe, and that the planets, including the earth, orbited the sun.

Copernicus's theories gained widespread scientific acceptance during his lifetime due to a number of factors.Copernicus's theories were met with resistance by some at first, as they contradicted the Aristotelian worldview that was prevalent at the time.

However, Copernicus's theories gained acceptance among his contemporaries due to a variety of factors.First, Copernicus was not the only astronomer to propose a heliocentric model of the universe. Aristarchus of Samos had proposed such a theory over a thousand years earlier, and other astronomers such as Nicholas of Cusa had also suggested similar models.

Second, Copernicus's theories were supported by empirical observations. Copernicus was not only an astronomer but also a mathematician and his extensive calculations demonstrated that the heliocentric model could explain the movements of the planets with greater accuracy than the geocentric model.Third, Copernicus's theories were more elegant than the Ptolemaic model.

In the Ptolemaic model, the planets move in complex epicycles, or circles within circles, in order to explain their movements. Copernicus's model, on the other hand, used simple circular orbits, making it more aesthetically pleasing.

Know more about astronomer here:

https://brainly.com/question/1764951

#SPJ11

A small stone has a mass of 1 g or 0.001 kg. The stone is moving with a speed of 12.000 m/s (roughly the escape speed). (a) a. What is wavelength of the stone? Report your answer to 2 decimal places, in scientific notation, and do NOT include units of measure. Wavelength = ×10 to the power of meters (b) Comment on why we do not "see" this wave nature of the stone. The Planck's constant h is 6.6×10 −34
J⋅s. (where 1 J⋅s=kg⋅m 2
/s ).

Answers

(a) The wavelength of the stone is approximately 5.50 × 10⁽⁻³⁴⁾⁾ meters. (b) We do not perceive the wave nature of macroscopic objects like stones due to their extremely small wavelengths, which are far below the scale of our everyday experiences.

(a) To find the wavelength of the stone, we can use the de Broglie wavelength formula:

λ = h / (m * v)

where:

λ = wavelength

h = Planck's constant (6.6×10⁽⁻³⁴⁾⁾ J⋅s)

m = mass of the stone (0.001 kg)

v = velocity of the stone (12.000 m/s)

Substituting the given values into the formula:

λ = (6.6×10⁽⁻³⁴⁾⁾ J⋅s) / (0.001 kg * 12.000 m/s)

Calculating this, we get:

λ = 5.50 × 10⁽⁻³⁴⁾⁾ meters

Therefore, the wavelength of the stone is approximately 5.50 × 10⁽⁻³⁴⁾⁾ meters.

(b) We do not perceive the wave nature of macroscopic objects like stones because their wavelengths are incredibly small compared to the scale of our everyday experiences. In the case of the stone mentioned, the wavelength is on the order of 10⁽⁻³⁴⁾⁾meters, which is many orders of magnitude smaller than anything we can observe directly. Our visual perception is limited to wavelengths within the visible light spectrum, which ranges from approximately 400 to 700 nanometers (10⁽⁻⁹⁾ meters). Therefore, the wave nature of the stone is not detectable by our senses. We need specialized equipment and experiments to observe the wave-like behavior of such small particles.

To know more about wavelength refer here

brainly.com/question/7143261

#SPJ11

There are 3 balloons sitting next to each other, each of a different size. What is in the biggest one?

a. 3 moles H2 (atomic mass of 2 AMU)

b. 2 moles Neon (atomic mass of 20 AMU)

d. it is impossible to determine

e. All three of these balloons would be almost the same volume

Answers

There are 3 balloons sitting next to each other, each of a different size, then The two moles Neon (atomic mass of 20 AMU) in the biggest one. This is option B

From the question above, three balloons are sitting next to each other, each of different size, and we're supposed to find out what is in the biggest one, i.e., which balloon is the biggest one.

We can determine the answer by using the ideal gas law (PV=nRT) and the molar mass of the gases to determine which gas has the highest mass and is present in the largest volume balloon.If all balloons contain the same number of moles of gas, then the biggest balloon will be the one with the highest molar mass gas because the same number of moles of the gas occupies more volume compared to the gas with a lower molar mass.

The molar mass of H2 is 2 g/mol, while the molar mass of Neon is 20 g/mol.

Therefore, the largest balloon will contain Neon (Option b) as it has the highest molar mass and occupies more volume than the gas with a lower molar mass.

Hence, the correct answer is Option b: 2 moles Neon (atomic mass of 20 AMU).

Learn more about gasses at

https://brainly.com/question/15307378

#SPJ11

a- Find the transfer function, \( G(s)=X(s) / F(s) \), for the translational mechanical system shown in Figure \( 1 . \) b- Find the rise time Tr, settling time Ts, damping ratio, percentage overshot,

Answers

a. The transfer function for the translational mechanical system shown in Figure 1 is given as follows:[tex]$$G(s)=\frac{X(s)}{F(s)}=\frac{1}{m s^{2}+b s+k}$$where $m$[/tex] is the mass of the block, b is the damping coefficient, k is the spring constant,

X(s) is the Laplace transform of the output displacement x(t), and F(s) is the Laplace transform of the input force f(t).The rise time T_r, settling time T_s, damping ratio \zeta, and percentage overshoot \%OS can be calculated from the transfer function as follows:[tex]$$\zeta =\frac{b}{2\sqrt{mk}}$$ $$\

omega_{n}=\sqrt{\frac{k}{m}}$$ $$

T_{r}=\frac{1.8}{\omega_{n}}$$ $$

T_{s}=\frac{4}{\zeta\omega_{n}}$$ $$\%

OS= e^{-\frac{\zeta\pi}{\sqrt{1-\zeta^{2}}}}\times100\%$$[/tex]where $\omega_n$ is the natural frequency of the system and is given by \sqrt{\frac{k}{m}}.

Hence, the rise time [tex]$T_r$ is $$T_{r}=\frac{1.8}{\sqrt{\frac{k}{m}}}$$[/tex]The settling time [tex]$T_s$ is $$

T_{s}=\frac{4}{\zeta\sqrt{\frac{k}{m}}}$$[/tex]The damping ratio [tex]$\zeta$ is $$\

zeta =\frac{b}{2\sqrt{mk}}$$[/tex]The percentage overshoot [tex]$\%OS$ is $$\%

OS= e^{-\frac{\zeta\pi}{\sqrt{1-\zeta^{2}}}}\times100\%$$[/tex]

To know more about percentage visit:

https://brainly.com/question/32197511

#SPJ11

Gas is confined in a tank at a pressure of 11.0 atm and a temperature of 25.0°C. If two thirds of the gas is with-drawn and the temperature is raised to 75.0°C, what is the new pressure in the tank?
A. 41.3 atm
C. 19.3 atm
B. 38.5 atm
D. 99.0 atm

Answers

The new pressure in the tank is 41.3 atm. This is calculated using the combined gas law.

When two thirds of the gas is withdrawn, the remaining gas occupies one third of the original volume. Since the temperature remains constant and the amount of gas is reduced, the pressure in the tank decreases.

To calculate the new pressure, we can use the combined gas law, which states that the product of pressure and volume is directly proportional to the product of the number of moles and temperature. Mathematically, this can be represented as P1V1/T1 = P2V2/T2, where P1 and T1 are the initial pressure and temperature, P2 and T2 are the final pressure and temperature, and V1 and V2 are the initial and final volumes.

Given that the initial pressure is 11.0 atm, the initial temperature is 25.0°C (298.15 K), and the final temperature is 75.0°C (348.15 K), we can rearrange the formula to solve for the final pressure:

P2 = (P1 * V1 * T2) / (V2 * T1)

Since two thirds of the gas is withdrawn, the final volume V2 is one third of the initial volume V1. Substituting the values into the equation, we get:

P2 = (11.0 atm * V1 * 348.15 K) / (V1 * 298.15 K / 3)

Simplifying the equation further, we find:

P2 = 41.3 atm

Therefore, the new pressure in the tank is 41.3 atm.

Learn more about gas law

brainly.com/question/30458409

#SPJ11

The new pressure in the tank, after withdrawing two-thirds of the gas and raising the temperature to 75.0°C, is approximately 41.3 atm.

To solve this problem, we can use the combined gas law, which states that the ratio of pressure to temperature is constant for a fixed amount of gas. The equation for the combined gas law is:

(P1 * V1) / (T1) = (P2 * V2) / (T2)

In this case, we can assume that the volume of the gas remains constant since the tank is confined. Let's denote the initial pressure and temperature as P1 and T1, respectively, and the final pressure and temperature as P2 and T2.

Initially, the pressure P1 is 11.0 atm and the temperature T1 is 25.0°C. Two-thirds of the gas is withdrawn, which means the remaining gas occupies one-third of the initial volume. The final temperature T2 is raised to 75.0°C.

Using the combined gas law, we can write:

(P1 * V) / (T1) = (P2 * (1/3V)) / (T2)

Since the volume V cancels out, we can rearrange the equation to solve for P2:

P2 = (P1 * T2 * 3) / (T1)

Plugging in the values, we have:

P2 = (11.0 atm * 75.0°C * 3) / (25.0°C) = 41.3 atm (approximately)

Therefore, the new pressure in the tank is approximately 41.3 atm.

Learn more about the pressure

brainly.com/question/30673967

#SPJ11

A generator supplies 20kVA to a load that produces 13,500 watts of actual power. The phase angle of this circuit is:

A. 34
B. 66
C. 47.5
D. 90

Answers

The phase angle of the circuit is 47.5° for generator supplies 20kVA to a load that produces 13,500 watts of actual power. The correct answer is option C.

The given terms in the question are: Generator, load, kVA, watts, and phase angle. A generator supplies 20kVA to a load that produces 13,500 watts of actual power. The phase angle of this circuit is to be determined.

The phase angle is the difference between the voltage and current in the circuit, given in degrees or radians. To calculate the phase angle, the reactive power Q and the actual power P of the circuit must be determined.

The apparent power S is the product of the voltage and current of the circuit. It is measured in VA (volt-amps) or kVA (kilo-volt amps).

S = VI

Where, V is the voltage, and I is the current.

The actual power P is the power that the circuit consumes in doing work. It is measured in watts (W) or kilowatts (kW).P = VI cos(ϕ)

Where, ϕ is the phase angle of the circuit.

The reactive power Q is the power that is not used by the circuit. It is measured in VAR (volt-amps reactive) or kVAR (kilo-volt amps reactive).

Q = VI sin(ϕ)

Where, ϕ is the phase angle of the circuit.

The apparent power S of the circuit is 20kVA.

The actual power P of the circuit is 13,500 W.

The reactive power Q of the circuit can be calculated by,

Q = √((S)^2 - (P)^2)

Q = √((20,000)^2 - (13,500)^2)

Q = √((400,000,000) - (182,250,000))

Q = √(217,750,000)

Q = 14,759 VAR

The phase angle ϕ can be calculated by,

ϕ = cos^-1(P/S

)ϕ = cos^-1(13,500/20,000)

ϕ = cos^-1(0.675)ϕ = 47.5°

Therefore, The correct answer is option C.

To learn more about circuit click here:

https://brainly.com/question/2969220#

#SPJ11


explain
why Two coils are said to be mutually coupled if the magnetic
flux Ø emanating from one pass
through the other

Answers

The mutual coupling between two coils occurs when the magnetic flux generated by one coil passes through the other coil. This phenomenon is crucial for various applications involving electromagnetic induction, such as transformers, where it enables the transfer of electrical energy between circuits.

Two coils are said to be mutually coupled when the magnetic flux Φ generated by one coil passes through the other coil. This phenomenon occurs due to the principles of electromagnetic induction. When there is a changing current in one coil, it produces a changing magnetic field around it. This changing magnetic field induces an electromotive force (EMF) in the second coil, resulting in the flow of current through it.

The level of mutual coupling between two coils depends on several factors, including the number of turns in each coil, the distance between them, and the permeability of the medium between them. If the coils are closely placed and have a large number of turns, the magnetic flux passing through the second coil will be significant, resulting in a stronger mutual coupling.

Mutual coupling between coils is a fundamental principle in various applications of electromagnetic devices. It is commonly utilized in transformers, where two coils are coupled to transfer electrical energy from one circuit to another. The primary coil, connected to a power source, generates a magnetic field that induces a voltage in the secondary coil, allowing power transfer between the two circuits.

Therefore, The mutual coupling between two coils occurs when the magnetic flux generated by one coil passes through the other coil. This phenomenon is crucial for various applications involving electromagnetic induction, such as transformers, where it enables the transfer of electrical energy between circuits.

Learn more about mutual coupling

https://brainly.in/question/3467821

#SPJ11

Mass of a marble is 0.01 kg and it is tossed at 1.0 m/s to the wall. The thickness of the wall 0.2 m. Can the marble tunnel through the wall? Explain by using a quantum effect.


Kindly answer all the question. Write in good handwriting and send clearer picture. Please answer all of the question. Thanks for your help. need fast responce.

Answers

According to classical physics, it is not possible for a marble with a mass of 0.01 kg and a velocity of 1.0 m/s to tunnel through a wall that is 0.2 m thick.

However, in quantum physics, there is a phenomenon known as quantum tunneling, which allows particles to pass through potential barriers that they should not be able to pass through according to classical physics.
Quantum tunneling is a quantum mechanical phenomenon in which a particle passes through a barrier that it shouldn't be able to pass through according to classical physics. The phenomenon occurs because, in quantum mechanics, particles can exist in a state known as a superposition, which means that they exist in multiple states simultaneously.

In the case of the marble and the wall, the marble could tunnel through the wall if it were able to exist in a state of superposition that allowed it to exist on both sides of the wall simultaneously.


To know more about mass visit:

https://brainly.com/question/11954533

#SPJ11

Electro-mechanical brakes on rotating equipment are more often used as an adjunct to dynamic braking as:
a)The electro-mechanical brake is needed in case the dynamic braking fails.
b)Electro-mechanical braking was used before dynamic braking became viable and it has retained its place due to tradition.
c)Dynamic braking will only bring the equipment to a standstill and the electro-mechanical brake is used to secure it. E.g. stop conveyors from reversing, etc.
d)The two systems operate together to bring the equipment to a stop sooner.

Answers

Electro-mechanical brakes on rotating equipment are more often used as an adjunct to dynamic braking as: c) Dynamic braking will only bring the equipment to a standstill and the electro-mechanical brake is used to secure it. E.g. stop conveyors from reversing, etc. Thus, the correct answer is option C.

Option A is incorrect as the electro-mechanical brake cannot be a backup for dynamic braking since it does not have a backup supply.

Option B is incorrect as electro-mechanical braking was not used before dynamic braking became viable and it does not retain its place due to tradition.

Option D is incorrect as the two systems do not operate together to bring the equipment to a stop sooner. Electro-mechanical braking on rotating equipment is usually an adjunct to dynamic braking to secure the equipment in place after the dynamic braking system has brought it to a standstill.

To know more about brakes, refer

https://brainly.com/question/29671080

#SPJ11

If two forces lying in the same plane are added together and the result is zero, which of the following is true of the forces?

Answers

The forces are equal in magnitude and opposite in direction.
Other Questions
summary of the Collective Agreement Between Social SecurityBoard And Christian Workers Union Covering Union Members Calculate the deflection of a particle thrown up to reach a maximum height zo, and that of a particle dropped from rest from the same height, due to the Coriolis force. For simplicity, you can assume that the particle was thrown straight up from the equator. SMO ANO Wallachination design occurs whenig kesa surface at a wide angle and it provides even lighting on a vertical space, Increase Luminances of wall surfaces and extend the space.a. Trueb. False the behavior of a wildfire is typically describedby:a) spread and recurrenceb) intensity and spreadc) temperature and locationd) severity and seasonalitye) recurrence and fuel composition What are your views regarding using credit cards?What can you do to build a strong credit history? argent pleaceUse MARS software to develop a well-documented MIPS Assembly program that: 1) defines in the data segment a static matrix named mymat consisting of \( 6 \times 8 \) elements and initializes them with In the absence of the SRY protein, the indifferent gonad:Select one:a. becomes a testicle.b. atrophies.c. becomes both an ovary and a testicle.d. becomes an ovary. The wavelengths of sound that carry farther in air are relativelyA) long.B) short.C) ultrasonic. explain how the host found the molar mass of sucrose. in what kind of organisms is cell specialization a characteristic Let f(x)= 72x. Then the expression f(x+h)f(x)/hcan be written in the form A/(Bx+Ch)+(x)where A,B, and C are constants. (Note: It's possible for one or more of these constants to be 0 .) Find the constants. A= _______B= ________C= ______ how many seconds can you hold the frisbee in ultimate frisbee [3] (a) Define the following terms and illustrate your answer with simple sketches (i) multiplexer (ii (iii) Demultiplexer (b)List two types of digital registers you know and show with the aid of a sketch how data is transferred from one flip flop to the next of the registers you have listed above. [12marks] Can we forgive and forget? Choose one of the following brands and describe the problem that was connected with the company, how did the problem play out and how did the company attempt to solve the issue. Tylenol (1982), Ford Pinto (1978), Vioxx (2004, Mattel (2007) Firestone (2000 Emily Rodriguez Court CaseDescribe Daniel Burns' role at Stone Creative. By approximately what percentage of its original length is a free DNA strand shortened by the coiling around a single histone? (Note: A histone has a diameter of 11 nm; assume inter-histone length is negligible.)A. 25%B. 50%C. 75%D. 100% PM Project Plan Assignment 3 (20%)Assignment 3: Project PlanComplete you project plan and include:1. Development of Scope, WBS2. Work on timelines, schedules3. Work on costs, budgets4. Identification of stakeholders5. Development of staffing, HR plan6. Work on Communication, Quality plans7. Procurement plans Compare and contrast VPN to other WAN solutions. 1. Packet Switched Networks: - IP/Ethernet - Frame Relay 2. Circuit-Switched Networks: - T-Carrier - SONET the nurse is teaching breathing exercises to a client who underwent surgery. which member of the healthcare team is most suitable for reinforcement of teaching in the client? i. DVLA Appii. ECG Mobile AppTell us what kind of business model they use.The kind of shopping chart usedIndicate their revenue model