6. The work W done by a force
F
is given by the line integral W=∫
F
⋅d
l
. Calculate the work done by the force
F
=(3xy;−5z;10x) along the curve described by x=t
2
,y=2 and z=t
3
from t=1 to t=2.

Answers

Answer 1

The work done by force F along the given curve is 260.4.

Force is, F = (3xy; −5z; 10x) along the curve, x = t², y = 2 and z = t³from t = 1 to t = 2.

The work done by the force F is given by the line integral as, W = ∫F.dl

To find the work done by force F, we need to calculate the value of this line integral over the given curve.

Substituting the given values of x, y, and z in the given expression of F, we get: F = (3t²(2); −5t³; 10t²) = (6t²; −5t³; 10t²)

Now, the differential length element dl along the curve can be written as dl = dx I + dy j + dz k = (2t dt) I + 0 j + (3t² dt) k The dot product of F and dl can be written as F . dl = (6t²)(2t dt) + (−5t³)(0) + (10t²)(3t² dt)= 12t⁴ dt + 30t⁴ dt= 42t⁴ dt

Now, the line integral of F along the given curve can be written as W = ∫F.dl= ∫₁² (42t⁴ dt)= [ 42 (t⁵)/5] ₁²= 42(2⁵ − 1⁵)/5= 42(31)/5= 260.4

To know more about the work done please refer to:

https://brainly.com/question/25573309

#SPJ11


Related Questions




1. Describe a scenario that makes it seem like you're still when in reality are travelling at a constant speed. Or, alternatively, where you seem to be going backwards but you're actually unmoving.

Answers

One scenario where you may appear still, but are traveling at a constant speed, is if you are on a train. If you are inside a train moving at a constant speed, everything inside the train is also moving at that same speed. Therefore, to you, it appears as if you are still when you are actually moving.

One scenario where you may appear still, but are traveling at a constant speed, is if you are on a train. If you are inside a train moving at a constant speed, everything inside the train is also moving at that same speed. Therefore, to you, it appears as if you are still when you are actually moving. This is why people often feel like they are being pulled backwards when a train starts to move: their body is trying to remain still while the train accelerates around them, causing them to feel like they are moving backwards. However, this is just an illusion created by the fact that their body is not moving at the same speed as the train.

Another scenario where you may appear to be going backwards, but are actually unmoving, is if you are sitting in a parked car with the engine running. When you are in a stationary car with the engine on, the wheels are not moving, but the engine is still running, causing vibrations to be felt throughout the car. When you put the car in reverse, the car's transmission engages, causing the wheels to spin in the opposite direction of what they normally would. This creates the illusion that you are moving backwards when, in reality, you are still sitting in the same spot. It's important to note that you should never engage the car's transmission unless you are in an open area and are certain there are no obstacles in your path.

To know more about speed visit:

https://brainly.com/question/6280317

#SPJ11

A 0.63 T magnetic field is perpendicular to a circular loop of wire With 65 turns and a radius of 13 cm Part A For the steps and strategies imvolved in solving a similar If the magnetic field is reduced to zero in 0.11 s, what is the magnitude of the induced omt? problem, you may view the following Examale 23.4 video: Express your answer in volts.

Answers

The magnitude of the induced emf is -65 * (ΔΦ / 0.11 s) for the magnetic field reduced to zero in 0.11 s.

The magnitude of the induced emf can be calculated using Faraday's Law of electromagnetic induction. The equation for Faraday's Law is:
emf = -N * (change in magnetic flux / change in time)
where ,

emf is the induced electromotive force,

N is the number of turns in the wire loop,

the change in magnetic flux is given by the product of the magnetic field strength and the area of the loop.
In this case, we are given:
- Magnetic field strength (B) = 0.63 T
- Number of turns (N) = 65
- Radius of the loop (r) = 13 cm = 0.13 m
- Change in time (Δt) = 0.11 s
To find the change in magnetic flux, we need to calculate the area of the loop. The formula for the area of a circle is:
Area = π * r^2
where

π is a constant (approximately equal to 3.14)

r is the radius of the loop
Using the given values, we can calculate the area of the loop:
Area = π * (0.13 m)^2
Now, we can calculate the change in magnetic flux:
ΔΦ = B * Area
Substituting the given values, we get:
ΔΦ = 0.63 T * (π * (0.13 m)^2)
Finally, we can calculate the magnitude of the induced emf using Faraday's Law:
emf = -N * (ΔΦ / Δt)
Substituting the given values, we get:
emf = -65 * (ΔΦ / 0.11 s)

Learn more about magnetic field

https://brainly.com/question/13160823

#SPJ11

a vertical long-run phillips curve is consistent with

Answers

A vertical long-run Phillips curve is consistent with the idea that there is no long-run trade-off between inflation and unemployment.

The Phillips curve is a graphical representation of the relationship between inflation and unemployment. In the short run, there is an inverse relationship between the two variables, meaning that as unemployment decreases, inflation tends to increase. However, in the long run, this relationship may not hold.

The long-run Phillips curve is often depicted as a vertical line, indicating that there is no trade-off between inflation and unemployment in the long run. This is because in the long run, the economy reaches its natural rate of unemployment, also known as the non-accelerating inflation rate of unemployment (NAIRU). At this level of unemployment, any attempt to reduce unemployment further through expansionary policies would only lead to higher inflation without any significant decrease in unemployment.

Therefore, a vertical long-run Phillips curve is consistent with the idea that there is no long-run trade-off between inflation and unemployment.

Learn more:

About vertical long-run Phillips curve here:

https://brainly.com/question/28199100

#SPJ11

A vertical long-run Phillips curve is consistent with the absence of a trade-off between inflation and unemployment in the long run.

A vertical long-run Phillips curve is consistent with the idea of a non-existent trade-off between inflation and unemployment in the long run. In other words, it suggests that there is no sustainable relationship between these two variables in the long term.

This concept is associated with the theory of the natural rate of unemployment, which posits that in the long run, unemployment will converge to its natural or equilibrium rate regardless of inflation levels. The vertical Phillips curve indicates that changes in inflation will not lead to lasting changes in unemployment rates.

A vertical long-run Phillips curve suggests that there is no stable or exploitable relationship between inflation and unemployment in the long term. This concept emerged as a result of the theory of the natural rate of unemployment, which argues that there is a certain equilibrium rate of unemployment that exists regardless of inflation levels.

According to this theory, any attempts to permanently reduce unemployment below this natural rate would only result in higher inflation without providing sustainable employment benefits.

The vertical Phillips curve reflects the idea that in the long run, changes in inflation do not have a lasting impact on unemployment rates, and vice versa. It indicates that policies focused solely on manipulating inflation levels would not be effective in achieving long-term reductions in unemployment.

To know more about unemployment refer here

https://brainly.com/question/4786400#

#SPJ11

a) with a neat sketch explain the concept of rotating magnetic field in induction motor. derive the expression of total flux for w=30deg
b) a dc motor operates with a load thst demands cinstant developed torque. with Vt=200V, the motor operates At 1200rpm anf has Ia=10A. the armature resistance is 5ohm and the field current remains constant. determine the speed if Vt is increased to 260V.

Answers

a) The expression for total flux is φ = φm sin θ, where θ = 30° yields φ = 0.5φm. b) When the armature voltage (Vt) in a DC motor with constant load torque and field current is increased from 200V to 260V, the new speed is (420 / π) rpm.

a) The induction motor is built on the principle of electromagnetic induction. The RMF is generated in the stator windings by the interaction between stator windings and the AC source. The three-phase AC is displaced by 120 degrees between each other, so when three-phase AC is given to the stator windings, a magnetic field is created that rotates at the same speed around the stator. This rotating magnetic field induces an EMF in the rotor conductors, which causes the rotor to rotate.

The expression for total flux can be calculated as φ = φm sin θ, where φm is the maximum flux and θ is the angular position of the rotor. The total flux is calculated using the given angular position w= 30 degrees which yields φ = 0.5φm.

b) When a DC motor operates with a constant load torque and a constant field current, the speed is inversely proportional to the armature voltage. In this case, the armature resistance is given as 5 ohms, and the field current remains constant. The armature voltage (Vt) is increased to 260V from 200V.

Now, let's determine the new speed by using the following formula;

Vt = E + Ia Ra where, E = back EMF, Ia = armature current, Ra = armature resistance.

Now, we can calculate the back EMF as follows;

E = Vt - Ia Ra = 260V - (10A × 5Ω)

= 210V

The new speed can be calculated as;

N2 = (E / Φ) (60 / 2π) where,Φ = φ / p = (Eb / K) / p (for a DC machine, φ = Eb)

K = 1 for a DC machine, p = number of poles

The new speed is calculated as;

N2 = (210V / 0.5φm) (60 / 2π)

= (420 / π) rpm

Learn more about induction motor here:

https://brainly.com/question/32808730

#SPJ11

In wind energy generation system, the wind energy is finally converted to __________ energy A. Chemistry B. Mechanic C. Potential D. Electrical

Answers

The answer to this question is D) Electrical. Wind energy is a renewable energy source which is converted from wind energy to electrical energy with the help of a wind turbine.

Wind turbines are designed to convert the kinetic energy of wind into mechanical energy and later this mechanical energy is converted to electrical energy.

Wind turbines have a rotor which contains blades that can be shaped like airfoil and the wind causes the blades to rotate and they drive a generator that produces electrical energy. The electrical energy generated from the wind turbines is then transferred to the national grid which then powers homes, factories and other appliances.

Learn more about Wind energy: https://brainly.com/question/16976863

#SPJ11

A mass m1 of steam at 100 oC is added to mass m2 of ice and mass M of water, both at 0 oC, in a container of negligible heat capacity. The specific heat of water is c. The latent heat of vaporization of water is L1 and that of the fusion of ice is L2.

Which one of the following equations would give the value of T, the final temperature of the system, assuming that all the steam condenses, all the ice melts, and that there are no heat exchanges with the surroundings?

Answers

The equation that would give the value of the final temperature (T) of the system in this scenario is:

[tex]m1 * c * (100 - T) + m2 * L2 + M * c * (T - 0) = m1 * L1[/tex]

Let's break down the equation:

- The first term, m1 * c * (100 - T), represents the heat lost by the steam as it cools down from 100°C to the final temperature T.

- The second term, m2 * L2, represents the heat required to melt the ice completely.

- The third term, M * c * (T - 0), represents the heat gained by the water as it warms up from 0°C to the final temperature T.

- The fourth term, m1 * L1, represents the heat released by the steam as it condenses completely into water.

By equating the heat lost by the steam to the heat gained by the water and ice, we ensure that energy is conserved in the system. This equation assumes that there are no heat exchanges with the surroundings, so all the energy transfer occurs within the system itself.

Solving this equation will give us the value of the final temperature (T) of the system after the steam condenses and the ice melts.

To know more about temperature visit:

brainly.com/question/12035620

#SPJ11

Q2)[3 Marks] Why is the stator core of Alternator laminated?
Q3) [3 Marks] What is the relation between electrical degree and mechanical degree?
Q4)[3 Marks] What happens to the iron loss and hence efficiency if the air gap flux density in an induction motor increases?

Answers

As the iron losses increase, the overall efficiency of the induction motor decreases. This is because the iron losses contribute to the total power loss in the motor, reducing the available power for useful mechanical output. Therefore, it is desirable to minimize the air gap flux density to improve motor efficiency and reduce iron losses.

Q2) The stator core of an alternator is laminated to reduce eddy current losses. Laminating the stator core means dividing it into thin insulated laminations or layers. This helps to minimize the flow of eddy currents, which are circulating currents induced in the core material due to the changing magnetic field.

By laminating the core, the eddy currents are confined to smaller paths within each lamination, reducing their magnitude and minimizing the associated energy losses. This improves the overall efficiency of the alternator.

Q3) The relation between electrical degree and mechanical degree is determined by the number of poles in an electrical machine. In electrical machines, such as synchronous motors or generators, the magnetic field produced by the poles rotates at a certain speed, known as the synchronous speed.

The synchronous speed is expressed in mechanical degrees per unit of time, usually rotations per minute (RPM) or radians per second (rad/s).

The number of electrical degrees per mechanical degree is determined by the number of poles in the machine. For a machine with P poles, there are 360 electrical degrees per mechanical revolution (360°). Therefore, the relationship between electrical degrees (θe) and mechanical degrees (θm) can be expressed as:

θe = (360 / P) * θm

Q4) If the air gap flux density in an induction motor increases, the iron losses in the motor will also increase. Iron losses consist of two components: hysteresis loss and eddy current loss.

Hysteresis loss is caused by the magnetic reversal of the iron core, and eddy current loss is caused by circulating currents induced in the core.

When the air gap flux density increases, the magnetic field strength in the core increases, leading to larger hysteresis losses. Hysteresis losses are proportional to the frequency and the area of the hysteresis loop, which is influenced by the magnetic field strength.

Additionally, higher air gap flux density results in increased eddy current losses. Eddy currents circulating within the core increase with higher flux density, leading to greater power dissipation and increased energy losses.

As the iron losses increase, the overall efficiency of the induction motor decreases. This is because the iron losses contribute to the total power loss in the motor, reducing the available power for useful mechanical output.

Therefore, it is desirable to minimize the air gap flux density to improve motor efficiency and reduce iron losses.

Learn more about magnetic field from the given link!

https://brainly.in/question/22520113

#SPJ11

1. (a) An object of mass 93.672 grams has a volume of 4.7 cm3. To the correct number of significant figures, determine the object's density in kg/m3. (10pts) (b) A small tennis ball is released (from rest) from a height of 10.0 m above the ground. How long does it take for the tennis ball to hit the ground? (8pts) (c) A small tennis ball is released (from rest) from a height of 10.0 m above the ground. Calculate the speed of the ball when it hits the ground. (7pts)

Answers

(a) An object of mass 93.672 grams has a volume of 4.7 cm³, it will take 1.42 seconds for the ball to hit the ground and its speed is 14 m/s when it hits the ground.

(a) An object of mass 93.672 grams has a volume of 4.7 cm³

To the correct number of significant figures, determine the object's density in kg/m³.

As given, the Mass of the object, m = 93.672 g

The volume of the object, v = 4.7 cm³ = 4.7 × 10⁻⁶ m³

Density, ρ = m/v = 93.672 g/4.7 × 10⁻⁶ m³

ρ = 19892468.09 kg/m³ ≈ 1.99 × 10⁷ kg/m³ (to 2 significant figures)

(b) A small tennis ball is released (from rest) from a height of 10.0 m above the ground.

How long does it take for the tennis ball to hit the ground?

Let's calculate using the kinematic equation, h = 1/2 gt² + vt

where, h = 10 m (height from which the ball is released)g = 9.8 m/s² (acceleration due to gravity)v = 0 m/s (initial velocity) and t = ?

Substitute all the values in the above kinematic equation

10 = 1/2 × 9.8 × t² + 0 × t10 = 4.9t²t² = 10/4.9t = √(10/4.9)t = 1.42

Therefore, it takes 1.42 seconds for the ball to hit the ground.

(c) A small tennis ball is released (from rest) from a height of 10.0 m above the ground.

Calculate the speed of the ball when it hits the ground. Using the kinematic equation, v² = u² + 2gh

where, u = 0 m/s (initial velocity)v = ? (velocity when the ball hits the ground)

g = 9.8 m/s² (acceleration due to gravity)

h = 10 m (height from which the ball is released)

Substitute all the values in the above kinematic equation

v² = 0² + 2 × 9.8 × 10v² = 196v = √196v = 14 m/s

Therefore, the speed of the ball, when it hits the ground, is 14 m/s.

If you need to learn more about volume click here:

https://brainly.com/question/27710307

#SPJ11

A three-phase delta connected induction motor with 220V, six-pole and 50Hz is running at slip of 3.0 percent. Its equivalent circuit components referred to stator are: R₁ = 0.2.2 R₂ = 0.132 X₁ = 0.412 X₂ = 0.45 2 jXM = 150 Hence, by using an approximate equivalent circuit, determine the following: i) The slip speed of the rotor ii) The rotor frequency in hertz iii) The total impedance of the circuit iv) The stator phase current v) The developed mechanical power

Answers

A three-phase delta connected induction motor with 220V, six-pole and 50Hz is running at slip of 3.0 percent. Its equivalent circuit components referred to stator are: R₁ = 0.2.2 R₂ = 0.132 X₁ = 0.412 X₂ = 0.45 2 jXM = 150.

The slip speed of the rotor The synchronous speed of the rotor (N_s) is given by:N_s = (120f)/pN_s = (120 × 50)/6N_s = 1000 rpm The speed of the rotor (N) can be given by:N = (1 - s)N_sWhere s is the sli p.N = (1 - 0.03) × 1000 rpm N = 970 rpm Therefore, the slip speed of the rotor is 30 rpm.ii) The rotor frequency in hertz The rotor frequency is given by:f_r = s × f_f_r = 0.03 × 50f_r = 1.5 Hz Therefore, the rotor frequency is 1.5 Hz.iii) The total impedance of the circuit The total impedance of the circuit is given by:Z = R_1 + (jX_1) + [(jX_M) × (R_2 + jX_2)] / (R_2 + jX_2 + jX_M)Z = 0.2 + j(0.412) + [(j150) × (0.132 + j0.45)] / (0.132 + j0.45 + j150)Z = 0.2 + j0.412 + 0.03 - j0.116Z = 0.23 + j0.296

Therefore, the total impedance of the circuit is 0.37 ohm. iv) The stator phase current The stator phase current is given by:I_1 = V / (Z × √3)I_1 = 220 / (0.37 × √3)I_1 = 344.7 A Therefore, the stator phase current is 344.7 A. v) The developed mechanical power The developed mechanical power is given by:P = 3 × V × I_2 × s / (2 × π)P = 3 × 220 × 334.11 × 0.03 / (2 × π)P = 388.9 W Therefore, the developed mechanical power is 388.9 W.

To know more about  mechanical power visit:-

https://brainly.com/question/12977725

#SPJ11

A 60 Hz, 3-phase, 12 pole synchronous motor connected as Y-configuration has rated voltage of 2300 V. The motor has a synchronous reactance of 4.5 n per-phase and a negligible armature resistance. The motor is connected to an infinite bus (at 2300 V) and draws 250 A at 0.8 power factor lagging. Neglecting rotational losses,
(a) Compute the output power.
(b) What is the maximum power the motor can deliver? Determine the torque, stator current (la), and the supply power factor at this condition.

Answers

The motor can deliver approximately 862.5 kW of power, with a torque of 2,886.29 Nm, a stator current of approximately 125.43 A, and a supply power factor of 1.

(a) Compute the output power:

The output power of the synchronous motor can be calculated using the formula:

Pout = √3 * Vline * Iline * power factor,

where Vline is the line voltage (2300 V), Iline is the line current (250 A), and the power factor is given as 0.8 lagging.

Substituting the values:

Pout = √3 * 2300 V * 250 A * 0.8

    ≈ 722,549.4 Watts (or 722.55 kW)

Therefore, the output power of the motor is approximately 722.55 kW.

(b) Determine the maximum power the motor can deliver:

The maximum power a synchronous motor can deliver is given by:

Pmax = (3/2) * Eline * Iline * power factor,

where Eline is the line voltage (2300 V), Iline is the line current (250 A), and the power factor is 1 (maximum power factor).

Substituting the values:

Pmax = (3/2) * 2300 V * 250 A * 1

     = 862,500 Watts (or 862.5 kW)

To determine the torque (T) at this maximum power condition, we can use the formula:

T = Pmax / (2π * f),

where f is the frequency (60 Hz) and T is the torque.

Substituting the values:

T = 862,500 Watts / (2π * 60 Hz)

   ≈ 2,886.29 Nm

The stator current (Ia) at maximum power can be calculated using:

Ia = (Pmax / (3 * Vline * power factor)),

where Pmax is the maximum power, Vline is the line voltage, and the power factor is 1.

Substituting the values:

Ia = 862,500 Watts / (3 * 2300 V * 1)

   ≈ 125.43 A

The supply power factor at this maximum power condition is 1.

Therefore, at the maximum power condition, the motor can deliver approximately 862.5 kW of power, with a torque of 2,886.29 Nm, a stator current of approximately 125.43 A, and a supply power factor of 1.

Learn more about synchronous motor from:

https://brainly.com/question/27189278

#SPJ11

The type of drilling that extracts mud through the center of the drill rod is:
a) percussion method
b) direct rotation method
c) reverse rotation method

Answers

The percussion method is the right anwser

Q6) For each of the following potential distributions, find the electric field intensity, the volume charge density, and the energy required to move 2 μc from A(3, 4, 5) to B(6, 8, 5): a. V = 2x² + 4y² b. V 10 p² sin q + 6pz c. V = 5r² cos sin p

Answers

The volume charge density is not defined in the given potential distributions. Therefore, its calculation is not possible in this case.

Electric field intensity (E), volume charge density (ρ), and energy (U) required to move 2μC from A(3, 4, 5) to B(6, 8, 5) are to be determined for the following potential distributions:

a. V = 2x² + 4y²

b. V = 10p² sin q + 6pz

c. V = 5r² cos sin p

Given data: A(3, 4, 5) and B(6, 8, 5)

Charge moved [tex]q = 2μc[/tex]

We know that the electric field intensity (E) is related to potential by [tex]E = - dV/dx - dV/dy - dV/dz[/tex] ……… (1)

The potential difference between two points A and B is given by [tex]VAB = VB - VA[/tex] ……….. (2)

The energy (U) required to move the charge from A to B is given by [tex]U = qVAB[/tex]……….. (3)

For any region where the volume charge density is constant, the volume charge density (ρ) is given by

ρ = Q/V ……….. (4)

where Q is the total charge in the region, V is the volume of the region.

Calculation for Electric field intensity, the volume charge density, and the energy required to move 2μC from A to B are: Case (a) [tex]V = 2x² + 4y²[/tex]

Let's first find the potential difference between A and B and the electric field intensity at point A.

Voltage difference VAB = VB - VA

= V(6,8,5) - V(3,4,5)

= [(2×6² + 4×8²) - (2×3² + 4×4²)] V

= [ 2×36 + 4×64 - 2×9 - 4×16 ] V

= 384 V

Then electric field intensity at point A is given by putting the values in equation (1)

[tex]E = - dV/dx - dV/dy - dV/dz[/tex]

= - 4xi - 8yj …………….(5)

Now, let's calculate the energy required to move 2μC from A to B.

Using equation (3)

[tex]U = qVAB[/tex]

= 2×10⁻⁶ × 384

= 0.000768 J

Case t(b) V = 10p² sin q + 6pz Let's first find the potential difference between A and B and the electric field intensity at point A.

Voltage difference

[tex]VAB = VB - VA[/tex]

= V(6,8,5) - V(3,4,5)

= [ 10×8² - 10×4² + 6×8 - 6×4 ] V

= 640 V

Then electric field intensity at point A is given by putting the values in equation (1)

E = - dV/dp - dV/dq - dV/dz

= - 80pcosq i - 20p²cos qj + 6k …………….(6)

Now, let's calculate the energy required to move 2μC from A to B.

Using equation (3)

U = qVAB

= 2×10⁻⁶ × 640

= 0.00128 J

Caset (c) V = 5r² cos sin p

Let's first find the potential difference between A and B and the electric field intensity at point A.

Voltage difference VAB = VB - VA = V(6,8,5) - V(3,4,5)

= [ 5×8² - 5×4² ] V

= 240 V

Then electric field intensity at point A is given by putting the values in equation (1)

[tex]E = - dV/dr - dV/dp - dV/dz[/tex]

= - 80rsinpcosq i - 40r²sinpsinqj …………….(7)

Now, let's calculate the energy required to move 2μC from A to B.

Using equation (3)

[tex]U = qVAB[/tex]

= 2×10⁻⁶ × 240

= 0.00048 J

The volume charge density is not defined in the given potential distributions. Therefore, its calculation is not possible in this case.

To know more about volume visit-

brainly.com/question/24927698

#SPJ11

Metal plates (k = 180 W/m-K, r = 2800 kg/m3 and cp = 880 J/kg-K) with a thickness of 1 cm are being heated in an oven for 2 minutes. Air in the oven is maintained at 800°C with a convection heat transfer coefficient of 200 W/m2 -K. If the initial temperature of the plates is 20°C, determine the temperature of the plates when they are removed from the oven.

Answers

The heat transfer through a metal plate that is being heated up in an oven for 2 minutes will be calculated as follows:

Q = kA (T2 – T1)/t Where: Q is the rate of heat transfer k is the thermal conductivity of the metal A is the surface area of the plate

T2 is the final temperature of the plate

T1 is the initial temperature of the plate

t is the time taken to heat up the plate

From the given data:

k = 180 W/m-K

r = 2800 kg/m3

cp = 880 J/kg-K

thickness, L = 1 cm = 0.01 m

heating time, t = 2 minutes

Air temperature in the oven, T∞ = 800°C

Heat transfer coefficient, h = 200 W/m2-K

Initial temperature of the plate, T1 = 20°C = 293 K

Converting the temperature to Kelvin scale:

T2 – T1 = Q t/kA

= [hL/k]1/2 {2 [r cp / k]1/2 / 3.1416} [exp (-1.55 L {h/k}1/2 / [r cp ]1/2) – exp (-5.18 L {h/k}1/2 / [r cp ]1/2)] (T2 – T∞)

T2 – T1 = 1149.26 (T2 – T∞)exp (-1.55 L {h/k}1/2 / [r cp ]1/2) – exp (-5.18 L {h/k}1/2 / [r cp ]1/2)

T2= T1 + [1149.26 (T2 – T∞)] / [exp (-1.55 L {h/k}1/2 / [r cp ]1/2) – exp (-5.18 L {h/k}1/2 / [r cp ]1/2)]

Substituting the given values:

T2 = 20 + [1149.26 (1073 – 293)] / [exp (-1.55 × 0.01 × {200/2800×880}1/2) – exp (-5.18 × 0.01 × {200/2800×880}1/2)]

T2 = 20 + 655640.88 / [exp (-0.00392) – exp (-0.0131)]

T2 = 20 + 1128.34

T2 = 1148.34 K.

The temperature of the plates when removed from the oven is 1148.34 K.

To know more about heat transfer visit:

https://brainly.com/question/13433948

#SPJ11







Which of the following must be true if the steady state assumption is to be used? Fc k₁ →→ES Keat E+P E+S k_₁ O [E]T=[ES] O (kcat-k1) / k₁ = 1 O k₁[E][S] = kcat[ES] Ov=d[ES]/dt = 0

Answers

The correct answer is option C: k₁[E][S] = kcat[ES] must be true if the steady-state assumption is to be used.

The steady-state assumption states that the enzyme-substrate complex is formed and broken down at the same rate in catalysis. It means that the concentration of the enzyme-substrate complex remains constant with time.

Also, the rate of product formation is proportional to the concentration of the enzyme-substrate complex. Hence the following equation is true:v=d[ES]/dt = 0

Here, v is the reaction rate, and [ES] is the concentration of the enzyme-substrate complex.

When the steady-state assumption is applied, it allows us to simplify the enzyme kinetics equation that describes the rate of the enzymatic reaction.

Based on the steady-state assumption, the following equation can be derived:k₁[E][S] = kcat[ES]

To know more about enzyme kinetics equation please refer:

https://brainly.com/question/30894011

#SPJ11

Given the standard form filter transfer function, below, calculate the corner frequency (Hz). Vo/V1 = 1+ ST Assume T= 12.02 ms Give your answer to 2 d.p.

Answers

The corner frequency (fc) of the given filter transfer function is approximately 83.19 Hz.

To calculate the corner frequency (fc) from the given transfer function, we need to determine the value of S at the corner frequency.

The standard form transfer function is Vo/V1 = 1 + ST, where T represents the time constant of the filter.

At the corner frequency (fc), the magnitude of the complex variable S is equal to 1/T. Therefore, we can equate S = 1/T and solve for fc.

Given T = 12.02 ms (milliseconds), we need to convert it to seconds by dividing by 1000:

T = 12.02 ms = 12.02 × [tex]10^{-3[/tex] s

Now, substitute T into the equation:

S = 1/T

S = 1 / (12.02 × [tex]10^{-3[/tex])

S = 83.194 Hz

Therefore, the corner frequency (fc) is approximately 83.19 Hz (rounded to 2 decimal places).

To know more about frequency refer here

https://brainly.com/question/29739263#

#SPJ11

1-It is possible to determine the average kinetic energy of sample of gas molecules by directly measuring only the temperature of that sample.

2-As the temperature rises, the root mean squared velocity of the gas sample increases.

3-The molecules in a sample of massive gas will have a higher root mean squared velocity than the molecules in a sample of a less massive gas.

4-The hot air above a candle will be more dense than colder air surrounding it.

Answers

1) The average kinetic energy of a sample of gas molecules can be determined by directly measuring only the temperature of that sample. The average kinetic energy of gas molecules is proportional to the temperature of the sample, as long as the sample is ideal and its particles are not interacting with one another.

2) As the temperature rises, the root mean squared velocity of the gas sample increases. The root mean squared velocity of a sample of gas molecules is proportional to the square root of the absolute temperature of the sample, as long as the sample is ideal and its particles are not interacting with one another.

3) The molecules in a sample of massive gas will have a lower root mean squared velocity than the molecules in a sample of a less massive gas. The root mean squared velocity of gas molecules is inversely proportional to the square root of their mass. Therefore, lighter gas molecules will have a higher root mean squared velocity than heavier gas molecules at the same temperature.

4) The hot air above a candle will be less dense than the colder air surrounding it. When air is heated, its molecules gain kinetic energy and move faster, which causes them to spread out and become less dense. This leads to the hot air above a candle being less dense than the colder air surrounding it.

You can learn more about average kinetic energy at: brainly.com/question/28702344

#SPJ11

USE ORIGINAL ANSWER OR GET DOWNVOTED!
Explain the question in great detail and find the
highest-frequency square wave you can transmit under the assumption
that you could transmit digital data over FM

Answers

The highest-frequency square wave that can transmit under the assumption that you could transmit digital data over FM is limited by the maximum frequency deviation of the FM signal.

Frequency modulation (FM) is a technique of conveying digital data through radio signals. FM radio works by altering the frequency of the carrier wave to represent the information being transmitted. The bandwidth of an FM signal is determined by its maximum frequency deviation, which is the amount by which the instantaneous frequency of the modulated carrier signal differs from the center frequency. This deviation is determined by the modulation index (m) and the maximum modulating frequency (fm) as shown below:

Maximum frequency deviation = m x fm

Thus, the highest-frequency square wave that can be transmitted over FM is limited by the maximum frequency deviation (and hence the bandwidth) of the FM signal.

The highest-frequency square wave that can be transmitted under the assumption that you could transmit digital data over FM is limited by the maximum frequency deviation of the FM signal.

To know more bandwidth visit:

https://brainly.com/question/13439811

#SPJ11

When responding to sound, the human eardrum vibrates about its equilibrium position. Suppose an eardrum is vibrating with an amplitude of 7.4x107 m and a maximum speed of 2.7 x103 m/s. (a) What is the frequency (in Hz) of the eardrum's vibrations? (b) What is the maximum acceleration of the eardrum?
(a) Number ________
(b) Number _______

Answers

the amplitude of the human eardrum as 7.4  107 m and the maximum speed as 2.7  103 m/s. We have to determine the frequency and maximum acceleration of the eardrum vibrations.

a) Frequency (in Hz) of the eardrum's vibrations:

The frequency of the wave is the number of cycles per second, and it is given by f = v/, where v is the velocity of the wave and  is the wavelength. Frequency is inversely proportional to the period of vibration (T), so f = 1/T.

If the time taken to complete one cycle of vibration is T seconds, then the frequency of vibration is given by

f = 1/T; T = 1/f

Thus, the frequency (in Hz) of the eardrum's vibrations is 1.84  105 Hz.b) Maximum acceleration of eardrum vibrations: The maximum acceleration is given by amax = 2A, where  is the angular frequency of the wave.

The angular frequency is defined as  = 2 f. We can use the above equation to calculate the maximum acceleration of eardrum vibrations.

ω = 2πf = 2π(1.84 × 10−5)

= 1.16 × 10−4 s−1amax

= ω2A

= (1.16 × 10−4)2(7.4 × 107)

= 9.44 × 1015 m/s²

Therefore, the maximum acceleration of eardrum vibrations is 9.44  1015 m/s2.

To learn more about amplitude, visit:

https://brainly.com/question/9525052

#SPJ11

A 235-g sample of a substance is heated to 330 ∘C and then plunged into a 105-g aluminum calorimeter cup containing 175 g of water and a 17-g glass thermometer at 13.5 ∘C. The final temperature is 35.0∘C. The value of specific heat for aluminium is 900 J/kg⋅C∘ , for glass is 840 J/kg⋅C∘ , and for water is 4186 J/kg⋅C∘ . What is the specific heat of the substance? (Assume no water boils away.)

Answers

The specific heat of the substance is approximately 1700 J/kg⋅C°.

To determine the specific heat of the substance, we can use the principle of heat transfer. The heat gained by the water, aluminum cup, and glass thermometer is equal to the heat lost by the substance.

We can calculate the heat gained by the water using the formula Q = m * c * ΔT, where m is the mass, c is the specific heat, and ΔT is the change in temperature. By applying this formula to water, aluminum, and glass, we can obtain three equations. Solving these equations simultaneously, we find the specific heat of the substance is approximately 1700 J/kg⋅C°.

For more questions like Aluminum click the link below:

https://brainly.com/question/28989771

#SPJ11

Identify the form or forms of energy produced by each of the following electrical components.
Electrical component - Forms of energy
The heating element of an electric kettle - __________________
The piezoelectric crystal in a speaker - __________________
The incandescent light bulb of a flashlight - __________________
The electromagnet in a tape recorder - __________________
The screen of a television - __________________
The motor of a mixer - __________________

Answers

The forms of energy produced by each of the electrical components are given below:

The heating element of an electric kettle - Thermal energy

The piezoelectric crystal in a speaker - Sound energy

The incandescent light bulb of a flashlight - Light and heat energy

The electromagnet in a tape recorder - Magnetic energy

The screen of a television - Light and electrical energy

The motor of a mixer - Mechanical energy

The forms of energy produced by each of the electrical components are given below:

The heating element of an electric kettle - Thermal energy: The heating element of an electric kettle converts electrical energy into heat energy, which is used to heat the water.The piezoelectric crystal in a speaker - Acoustic energy: The piezoelectric crystal in a speaker converts electrical energy into mechanical vibrations, which produce sound waves and generate acoustic energy.The incandescent light bulb of a flashlight - Light energy and Thermal energy: The incandescent light bulb converts electrical energy into light energy, which illuminates the surroundings. However, it also generates thermal energy due to the heat produced by the glowing filament.The electromagnet in a tape recorder - Magnetic energy: The electromagnet in a tape recorder converts electrical energy into magnetic energy. It creates a magnetic field that interacts with the tape, allowing the recording and playback of audio signals.The screen of a television - Light energy: The screen of a television, whether it is an LCD, LED, or OLED display, converts electrical energy into light energy. The electrical signals control the emission of light pixels, producing the visual display.The motor of a mixer - Mechanical energy: The motor of a mixer converts electrical energy into mechanical energy. It powers the rotation of the mixer's blades, allowing them to mix or blend ingredients.

For more such questions on forms of energy, click on:

https://brainly.com/question/18963960

#SPJ8

(co 1) (3 Marks) (b) Plot the graphs of following functions and thereby explain whether they are acceptable wave functions or not. a) ₁(x) = [log(x)], b) ₂(x) = e-rª. (co 1) (2 Marks) 2 (₂) Dorivo the orn sion for the Compton shift (2 Marka)

Answers

The given function satisfies the normalization criteria. So it is an acceptable wave function. ∫₀^∞ e^-2x dx < ∞. The shift in wavelength of the photon is given by Compton shift λ - λ₀ = (h/mec)(1 - cos θ).

a) Plot the graphs of the following functions and explain whether they are acceptable wave functions or not: ₁(x) = [log(x)] and ₂(x) = e-rª.

(i) For the function ₁(x) = [log(x)]:

The given wave function is not an acceptable wave function as it does not meet the normalization criteria. A wave function is considered an acceptable wave function if it satisfies the normalization criteria, that is, the integral of its modulus square from -∞ to ∞ should be equal to 1.

i.e.  ∫₀¹ [log(x)]² dx < ∞ As we see here the limit of integration has 0 which is not correct so this cannot be a proper wave function(

ii) For the function ₂(x) = e-rª:

The given function satisfies the normalization criteria. So it is an acceptable wave function. ∫₀^∞ e^-2x dx < ∞

(b) Derive the expression for the Compton shift:

The Compton effect or Compton scattering is the inelastic scattering of a photon by an electron. The shift in wavelength of the photon is given by Compton shift

λ - λ₀ = (h/mec)(1 - cos θ)

Where λ₀ = wavelength of the incident photon

λ = wavelength of the scattered photon

θ = angle between the incident photon and the scattered photon

h = Planck's constant

me = mass of the electron

c = speed of light

To learn more about Compton shift:

https://brainly.com/question/29306626

#SPJ11

8. A particle is in the ground state of an infinite square well potential. Find the probability of finding the particle in the interval Ar = 0.002L at (a) x=L/2, (b) x=2L/3, and (c) x=L. (Since x is very small, you need not do any integration.)

Answers

The probability of finding a particle in the interval Ar at (a) x=L/2 and (b) x=2L/3 is 2/L and at (c) x=L is 0.

The interval in which the particle is present is Ar = 0.002L to be found at the following intervals: (a) x=L/2, (b) x=2L/3, and (c) x=L.

The probability of finding the particle can be calculated as follows:

Probability of finding a particle in the interval Ar at x= L/2, P = 2|ψ( L/2 )|² Here, |ψ( L/2 )|² = [sin(n π L/2L)]² / L= [sin(n π/2)]² / L= [sin( π/2 )]² / L [since n = 1, for ground state]

So, P = 2|ψ( L/2 )|²= 2 [sin( π/2 )]² / L = 2(1 / L)

The probability of finding a particle in the interval Ar at x= 2L/3, P = 2|ψ( 2L/3 )|²Here, |ψ( 2L/3 )|² = [sin(n π 2L/3L)]² / L= [sin(2n π/3)]² / L= [sin(2 π/3 )]² / L [since n = 1, for ground state]

So, P = 2|ψ( 2L/3 )|²= 2 [sin(2 π/3 )]² / L = 2(1 / L)

The probability of finding a particle in the interval Ar at x= L, P = 2|ψ( L )|²

Here, |ψ( L )|² = [sin(n π L/L)]² / L= [sin(n π )]² / L= [0]² / L [since sin(n π ) = 0]So, P = 2|ψ( L )|²= 0

Therefore, P = 2(0) = 0

To know more about ground state please refer to:

https://brainly.com/question/33289413

#SPJ11

Part II – Measuring distant objects [24 points] Parallax as
explained in the pre-lab activity, is an interesting way of
measuring the distance of an object by how much it appears to move
when viewed

Answers

wZAnswer:d

Explanation:

efwdx

Parallax is a valuable technique used in astronomy to measure the distances of nearby celestial objects accurately. It relies on the apparent shift in an object's position when viewed from different locations on Earth's orbit and utilizes trigonometry to calculate the distance to the object.

Parallax is the apparent shift or change in the position of an object when viewed from different perspectives. This effect occurs when an observer changes their viewing angle. In astronomy, parallax is used to measure the distances of stars, planets, and other celestial objects.

The principle behind parallax is simple: Observers on Earth have slightly different views of a nearby object compared to a distant one, due to the difference in the observer's location on the planet. By measuring the apparent shift in the position of an object when viewed from two different points (such as two different locations on Earth), astronomers can calculate the object's distance.

The baseline used for measuring the parallax is the distance between the two observing points. In the case of celestial objects, the baseline is the distance between two points on the Earth's orbit, which are six months apart. This is because the Earth's position is significantly different after half a year due to its revolution around the Sun.

To measure parallax accurately, astronomers use specialized instruments like telescopes and cameras to observe the position of stars or other celestial objects at different times of the year. By comparing the apparent shifts in the object's position, they can determine the parallax angle. Using trigonometry, they can then calculate the distance to the object.

The formula used to calculate the distance to the object is:

Distance (in parsecs) = 1 / Parallax (in arcseconds)

That 1 parsec is approximately equal to 3.26 light-years.

To know more about Parallax

https://brainly.com/question/33870669

#SPJ2

19-4
4 pts
Find the amount of heat required to vaporize 83.9 g of boiling water into steam. The latent heat of vaporization for water is given in a table in your reading assignment.
Q= ________ J (± 1E4 J)

Answers

It is necessary to find the amount of heat required to vaporize 83.9 grams of boiling water into steam. Let us first recall the definition of latent heat of vaporization. The latent heat of vaporization is the amount of energy required to change the phase of a substance from liquid to gas without changing its temperature. This means that during this process, there is no change in temperature.

The heat required to vaporize a certain amount of water can be calculated using the formula:

Q = mL

Where,

Q is the heat required,

m is the mass of water,

and L is the latent heat of vaporization for water.

We are given that the mass of water to be vaporized is 83.9 g. We need to find the latent heat of vaporization of water, which is provided in a table. It is 2.26 x 106 J/kg.

Substituting the values in the formula, we get:

Q = mL = 83.9 g x 2.26 x 106 J/kg

Q = 1.89 x 108 J

Therefore, the amount of heat required to vaporize 83.9 g of boiling water into steam is 1.89 x 108 J. This can also be written as 189,000,000 J.

Therefore, the required amount of heat is 1.89 × 108 J (± 1E4 J).

To know more about latent heat, visit:

https://brainly.com/question/23976436

#SPJ11

term Exam A Second Semester 2021-2022 23) One end of a steel rod of radius R-9.5 mm and length L-81 cm is held in a vise. A force of magnitude F#62 KN is then applied perpendicularly to the end face uniformly across the area) at the other end, pulling directly away from the vise. The elongation AL(in mm) of the rod is: (Young's modulus for steel is 2.0 × 10¹ N/m²) a) 0.89 b) 0.61 c) 0.72 d) 0.79 e) 0.58 Q4) A cylindrical aluminum rod, with an initial length of 0.80 m and radius 1000.0 mm, is clamped in place at one end and then stretched by a machine pulling parallel to its length at its other end. Assuming that the rod's density (mass per unit volume) does not change. The force magnitude (in N) that is required of the machine to decrease the radius to 999.9 mm is: (Young's modulus for aluminum in 7.0 × 10° N/m²) d) 34 e) 64 c) 50 b) 44 a) 58 to a maximum

Answers

The magnitude of the force required by the machine to decrease the radius to 999.9 mm is 34 N. The correct option is (d). The elongation (AL) of the steel rod can be calculated using the formula:

AL = FL / AE

Where,

F is the force applied

L is the length of the steel rod

A is the area of the cross-section of the rod

E is the Young's modulus

First, calculate the area of the cross-section of the steel rod:

A = πR²

A = π(9.5 mm)²

A = 283.5 mm²

Next, calculate the elongation of the steel rod:

AL = FL / AE

AL = 62 × 10³ N / (2 × 10¹¹ N/m² × 283.5 × 10⁻⁶ m²)

AL = 0.89 mm

Therefore, the elongation of the steel rod is 0.89 mm. The correct option is (a) 0.89.

Let the force required by the machine be F. The change in radius is:

ΔR = R - R₀ = 1000.0 mm - 999.9 mm = 0.1 mm

The change in length is given by:

ΔL = R₀LΔR / R³ = (1000.0 mm)(0.1 mm) / (1000.0 mm)³

ΔL = 1 × 10⁻⁷ m

The increase in volume of the rod is given by:

ΔV = π[R² - (R - ΔR)²] L

ΔV = π[1000.0² - 999.9²] × 0.80

ΔV = 0.1256 m³

Using the density formula, we have:

density = mass / volume

Since the density of the rod is constant, the mass of the rod does not change. Therefore, we can write the equation as:

ρ₀V₀ = ρV

Where,

ρ₀ is the initial density of the rod

V₀ is the initial volume of the rod

ρ is the final density of the rod

V is the final volume of the rod

Substituting the value of ΔV in the equation, we get the final volume of the rod as:

V = V₀ + ΔV = (0.80 m)(1000.0 mm)² + 0.1256 m³

V = 1001000 mm³

The stress on the rod is given by:

σ = F / A

Where,

A is the area of the cross-section of the rod

The strain on the rod is given by:

ε = ΔL / L

The modulus of elasticity is given by:

E = σ / ε

E = (F / A) / (ΔL / L)

E = FL / AΔL

E = F(ΔL) / A

The force required can be calculated as:

F = σAE / ΔL

F = (σ × πR₀²) (LΔR / R³) (E)

F = (7.0 × 10¹⁰ N/m²) (π (1000.0 mm)²) (0.80 m) (0.1 mm / (1000.0 mm)³)

F = 34 N

To know more about magnitude visit:

https://brainly.com/question/31022175

#SPJ11

Question 2 For a tidal range at a particular place with 2 tides daily of 10 m, and the surface tidal energy harnessing plant of 9 km², if the specific gravity of water is 1025.18 kg/m³, determine the total energy potential per day of the plant. [8]

Answers

The total energy potential per day of the tidal energy harnessing plant is approximately 43.2 megawatt-hours (MWh).

The total energy potential per day of the plant is:

E = 2 * 9 * 10000 * 10 * 1025.18 * 9.81 = 18102628440 J

where:

E is the total energy potential per day (in joules)

2 is the number of tides per day

9 is the surface area of the plant (in km²)

10000 is the conversion factor from meters to kilometers

10 is the tidal range (in meters)

1025.18 is the specific gravity of water

9.81 is the acceleration due to gravity (in m/s²)

The total energy potential is then calculated by multiplying the volume of water by the specific gravity of water, the acceleration due to gravity, and the height of the tidal range.

The total energy potential per day is a very large number, approximately 18102628440 joules. This is equivalent to approximately 43.2 megawatt-hours (MWh).

To learn more about acceleration: https://brainly.com/question/29761692

#SPJ11

A cheetah can run at a maximum speed 101 km/h and a gazelle can run at a maximum speed of 74.4 km/h. If both animals are running at full speed, with the gazelle 58.7 m ahead, how long before the cheetah catches its prey? Answer in units of s. Answer in units of s part 2 of 2 The cheetah can maintain its maximum speed for only 7.5 s. What is the minimum distance the gazelle must be ahead of the cheetah to have a chance of escape? (After 7.5 s the speed of cheetah is less than that of the gazelle.) Answer in units of m.

Answers

Part 1: It takes approximately 7.94 seconds for the cheetah to catch its prey.

- Part 2: minimum distance the gazelle must be ahead of the cheetah to have a chance of escape is approximately 55.42 meters.

For Part 1 :  To do this, we can calculate the relative speed between the cheetah and the gazelle. The relative speed is the difference between their speeds.

Relative speed = Cheetah's speed - Gazelle's speed
Relative speed = 101 km/h - 74.4 km/h
Relative speed = 26.6 km/h

Now, we need to convert the relative speed from km/h to m/s, since we want the answer in units of seconds.

Relative speed = 26.6 km/h * (1000 m/1 km) * (1 h/3600 s)
Relative speed = 7.39 m/s

Now, we can calculate the time it takes for the cheetah to catch the gazelle using the formula:

time = distance/relative speed
time = 58.7 m / 7.39 m/s
time = 7.94 s

Therefore, it takes approximately 7.94 seconds for the cheetah to catch its prey.


For part 2 :  we need to calculate the minimum distance the gazelle must be ahead of the cheetah to have a chance of escape, given that the cheetah can maintain its maximum speed for only 7.5 s.

Using the same relative speed of 7.39 m/s, we can calculate the distance the cheetah can cover in 7.5 seconds.

Distance = speed * time
Distance = 7.39 m/s * 7.5 s
Distance = 55.42 m

Therefore, the minimum distance the gazelle must be ahead of the cheetah to have a chance of escape is approximately 55.42 meters.

To learn more about distance and relative speed;

https://brainly.com/question/11270989

#SPJ11

A flat roof of a house has a mass of 100kg and an area of 15m^2. The roof is only maintained in place by its weight, what should be the minimum velocity of the horizontal wind produced by a storm to lift the roof.

Answers

The minimum velocity of horizontal wind needed to lift the flat roof of a house is approximately 6.54 m/s.

To determine the minimum velocity of the horizontal wind needed to lift the flat roof of a house, we can use the concept of pressure difference. When wind blows over the roof, it creates a difference in pressure between the top and bottom surfaces of the roof.

The formula for pressure difference is:
Pressure difference = (density of air) x (velocity of wind)² x (area of the roof)

In this case, the roof is only maintained in place by its weight, which means the minimum velocity of the wind required to lift the roof is when the pressure difference exactly balances the weight of the roof.

The weight of the roof can be calculated using the formula:
Weight = mass x gravity

The mass of the roof is 100 kg, and the acceleration due to gravity is approximately 9.8 m/s², we can calculate the weight of the roof:
Weight = 100 kg x 9.8 m/s² = 980 N

Now, let's substitute the values into the pressure difference formula:
980 N = (density of air) x (velocity of wind)² x 15 m²

To solve for the velocity of wind, we need the density of air. The density of air can vary depending on factors such as temperature and altitude. At standard temperature and pressure (STP), the density of air is approximately 1.225 kg/m^3.

Substituting this value into the pressure difference formula:
980 N = (1.225 kg/m³) x (velocity of wind)² x 15 m²

Simplifying the equation:
(velocity of wind)² = 980 N / (1.225 kg/m³ x 15 m²)
(velocity of wind)^2 = 42.80 m²/s²

Taking the square root of both sides:
velocity of wind = √(42.80 m²/s²)
velocity of wind ≈ 6.54 m/s

Therefore, the minimum velocity of the horizontal wind produced by a storm to lift the roof is approximately 6.54 m/s.

To know more about minimum velocity, refer to the link below:

https://brainly.com/question/13104567#

#SPJ11

An oven plate used for heating substances is 0.012m thick. The top surface of the oven is exposed to air flowing at 20°C. In an experiment, the plate is heated by electrical heater positioned on the underside of the plate and the temperature is maintained at 120°C. Calculate the temperature of the top surface. The plate is made of stainless steel with thermal conductivity of 16 W/m °C. The convective heat transfer coefficient of air is 2.5 W/m² °C and the total area of the plate is 1m²

Answers

The temperature of the top surface is 63°C.A stainless steel oven plate that is 0.012m thick is being used to heat substances in this scenario. The top surface of the oven plate is exposed to air flowing at 20°C, while an electric heater on the underside of the plate heats it and maintains it at 120°C.

The plate is 1m² in total area and has a thermal conductivity of 16 W/m°C. The convective heat transfer coefficient of air is 2.5 W/m² °C.

Calculate the temperature of the top surface:

Q/A = h(T - T∞) / L + k(T1 - T2) / LQ/A

= h(T - T∞) / L + k(T1 - T2) / LHere,

L = 0.012

m = 0.012 × 10³ mm

K = 16 W/m°CQ/A

= (2.5 W/m²°C) × (120°C - 20°C) / 0.012m + (16 W/m°C) × (T1 - 120°C) / 0.012m

This can be simplified to

104000 = 8333.3 + 1333.3(T1 - 120°C)104000 - 8333.3

= 1333.3(T1 - 120°C)95500

= 1333.3(T1 - 120°C)T1 - 120°C

= 71.3°C

As a result,

T1 = 120°C + 71.3°C

= 191.3°C

The temperature of the top surface is 63°C (191.3 - 120 - 20).

To know more about temperature visit:

https://brainly.com/question/7510619

#SPJ11

A chemist is trying to identify a sample of metal that is listed in this table. She passes an electrical current through the sample and finds that, of the metals listed in the table, it’s one of the best conductors. Then she heats the metal to 1000°C, which is the highest temperature her heater allows. The metal doesn’t melt. Which type of metal does the chemist have?

Material Melting Point (°C) Electrical Conductivity Ranking
aluminum 660 3
copper 1085 2
zinc 420 4
silver 962 1
nickel 1455 5
A.
aluminum
B.
copper
C.
zinc
D.
silver
E.
nickel

Answers

A chemist is trying to identify a sample of metal that is listed in this table. She passes an electrical current through the sample and finds that, of the metals listed in the table, it’s one of the best conductors. Then she heats the metal to 1000°C, which is the highest temperature her heater allows. The metal that the chemist has is A. aluminum.

The given information states that the metal is one of the best conductors among the metals listed in the table. Looking at the electrical conductivity rankings, we see that silver is ranked as the best conductor (ranked 1), followed by copper (ranked 2). Since the metal being tested is one of the best conductors, it must be either silver or copper.Next, the metal is heated to 1000°C, and it doesn't melt. By referring to the melting points listed in the table, we can see that copper has a melting point of 1085°C, while aluminum has a melting point of 660°C. Since the temperature used in the experiment is below the melting point of aluminum, but above the melting point of copper, we can conclude that the metal is aluminum.

Therefore, the chemist has aluminum.

For more such questions on metal, click on:

https://brainly.com/question/4701542

#SPJ8

Other Questions
which is incorrect regarding smooth muscle in the digestive tract? A non-specified divalent metal has a density of rho=6.4103 kg/m3 and a molar mass of 41.70 g/mol. Consider a cube with volume V=9.77 mm3 Part 1) How many conduction electrons are in the cube? N= conduction electrons Part 2) The Fermi energy is related to the number of conduction electrons per unit volume, n, through EF=(m0.121h2)n2/3 where m is the mass of the electron. What is the Fermi energy for this metal? A cable exerts a constant upward tension of magnitude 2.58104 N on a 2.40103 kg elevator as it rises through a vertical distance of 2.10 m. (a) Find the work done by the tension force on the elevator (in J). J (b) Find the work done by the force of gravity on the elevator (in J). J why do some of the feds critics think the fed should not engage in manipulating the nations money supply? SUPPLY CHAIN MANAGEMENT QUESTION: How do you know if your business is ready to export? According to the South African Department of Trade and Industry, there are a number of criteria that a business needs to meet in order for it to be ready to enter the international market of exporting. For this discussion, look at the DTI's survey which provides guidelines on a business's export guidelines.Which factor do you think is most important in assessing whether you are ready for exporting? How do you know if you are ready to enter into international trade? Do some research before answering the questions. You can compare the DTI's survey with other exportation assessment to enrich your answer. Calculate the error in the ammeter which reads 3.25 A inacircuit having a series standard resistance of 0.01, thepotential difference measured across this standard resistance being0.035V.Answer In which one of the following cases would the presence of defects be absolutely detrimental to the desired maferial properties? [1 mark] Select one: a. Antiphase boundaries in a jet engine turbine bla 7. Now shine light from a 640 nm laser onto a single slit of width 0.150 mm that is placed in front of a screen. You measure the distance on the screen between the second minima on either side of the central bright spot, and you find them to be 2.20 cm apart. How far away is the screen? A boiler uses 1,500,000 Therms of natural gas per hour to produce 100,000 MMBTU/hr of energy. Calculate the efficiency of this boiler (%). (5 points) 5) Consider the following transfer function of a system \( \quad G_{1}(s)=\frac{1}{s(s+1)} \) In the z-plane, design digital controllers so that the dominant closed-loop poles have \( \zeta=0.5 \) and En cierto laboratorio se cultiva la cepa de una bacteria, causal de mltiples problemas. Con fin de determinar la rapidez de reproduccin de dicha bacteria, esta se coloca en un medio de crecimiento y condiciones favorables. La poblacin existente es de 250 bacterias y se observa que cada hora se duplica la cantidad A clothing company releases two versions of the same dress - one black in color and another in red. The red dress is priced 30% higher than the black dress. What assumption does the company make about consumers that buy the red dress as compared to those who buy the black dress? a. Consumers that buy the red dress have a less price-elastic (or more price-inelastic) demand than those that buy the black dress b. Consumers that buy the red dress have a more price-elastic demand than those that buy the black dress c. Consumers that buy the red dress have the same price-elasticity of demand as those that buy the black dress d. Consumers that buy the red dress are not rational consumers 1. Describe the similarities and differences between absoluteuncertainty and relative uncertainty.Please type your answer in your own words. Thank you so much Read the passages.Passage 1: The Declaration of Independence, 1776We hold these truths to be self-evident, that all menare created equal, that they are endowed by theirCreator with certain unalienable Rights, that amongthese are Life, Liberty, and the pursuit of Happiness.-That to secure these rights, Governments areinstituted among Men, deriving their just powersfrom the consent of the governed. That wheneverany Form of Government becomes destructive ofthese ends, it is the Right of the People to alter or toabolish it, and to institute new Government, layingits foundation on such principles and organizing itspowers in such form, as to them shall seem mostlikely to effect their Safety and Happiness.Prudence, indeed, will dictate that Governmentslong established should not be changed for light andtransient causes and accordingly all experienceMark this and returnWhich statement best synthesizes information fromthese passages?The Declaration of Sentiments was written at theSeneca Falls Convention to explain why womenshould be afforded equal rights.In 1848, delegates at the Seneca FallsConvention used the Declaration ofIndependence to explain why women should haveequal rights.O The Declaration of Independence built on theideas of Enlightenment thinkers and has servedas inspiration for many people.In 1776, colonists came together to discuss therights of colonists. Similarly, in 1848, Americanscame together to discuss the rights of women.Save and ExitNextSubmit Which of the following is not typically assessed in the process of negotiating a position? (1.5 Points) a. Financial condition of the company b. Reputation of the company c. Size of the company d. Types of interpersonal relationships within the company Create a trigger named trg_line_total to write the LINE_TOTAL value in the LINE table every time you add a new LINE row. (The LINE_TOTAL value is the product of theLINE_UNITS and LINE_PRICE values).To test the trigger, insert the following record into the line table. invoice number: 1008, line number: 4, product code: 'SM-18277', line units: 2, line price: 6.99, line total: null.Then run SELECT * FROM LINE; In an effort to preserve the elephants, the government has decided to ban the ivory trade and outlaw the killing of elephants. What do you think would be the likely outcome of this solution? What might be a more effective alternative to saving these elephants? Q4. (12 points) Suppose two firms, All-American Power (Firm A) and Big Energy Inc. (Firm B) have the following marginal abatement cost curves: MACA = 300 3eA and MACB = 200 2eB, and the government wants to use an effluent tax to keep total emissions down to 50.A. (6 points) Draw a graph of each firm side by side, clearly marking the intercepts of their respective MAC curves. Calculate the optimal number of emissions for each firm given the efficiency and abatement constraints as well as the optimal tax rate necessary to get to those level of emissions. "Give an explicit explanation on the strength ofAltman's Z score and state at least a minimum of 5limitations of Altman's Z scoreNoteMinimum of 250 wordsProvide reference using Harvard style Complete the level production plan, using the following information. The only costs you need to consider here are layoff, hiring, and inventory costs. If you complete the plan correctly, your hiring, layoff, and inventory costs should match those given here. Click the icon to view the costs table. Click the icon to view the forecasted sales. Fill in the production plan table below (enter your responses rounded to the nearest whole number). focus groups are almost never used in public relations research.