85) What is the change in entropy when 15.0 g of water at 100°C are turned into steam at 100°C? The latent heat of vaporization of water is 22.6 × 105 J/kg.
A) 90.8 J/K
B) -90.8 J/K
C) 339 J/K
D) -339 J/K
E) 0 J/K

The charge on any one of the capacitors is 100 µC.

When capacitors are connected in parallel, the equivalent capacitance is the sum of the individual capacitances. In this case, the equivalent capacitance is 3 µF (1 µF + 1 µF + 1 µF = 3 µF).

The formula for capacitance is C = Q/V, where C is the capacitance in farads, Q is the charge in coulombs, and V is the potential difference in volts. Rearranging this formula gives Q = CV.

So, the charge on any one of the capacitors can be found by multiplying the equivalent capacitance (3 µF) by the potential difference (100 V), giving a total charge of 300 µC. Since the capacitors are connected in parallel, each capacitor has the same voltage across it and therefore carries a charge of 100 µC (one-third of the total charge).

Learn more about voltage here:

https://brainly.com/question/13521443

#SPJ11

The frequencies of light absorbed by an apple include those in the visible range, specifically in the blue and green wavelengths.

This is because apples predominantly reflect red light, which gives them their characteristic red color. Apples absorb blue and green light frequencies. To explain further, when light hits an object, some wavelengths are absorbed while others are reflected. In the case of a red apple, it absorbs shorter wavelengths (blue and green) and reflects the longer wavelength (red), resulting in the red color we perceive.

However, the pigments in the apple, such as chlorophyll and carotenoids, absorb specific wavelengths of light and reflect others.

To know more about wavelengths, visit:

https://brainly.com/question/13533093

#SPJ11

To find the time for a crest of the wave to travel the length of the wire, we need to use the formula:velocity = frequency x wavelengthFirst, we need to find the velocity of the wave on the wire. The wave is a transverse wave, which means it propagates perpendicular to the direction of the tension force.

The velocity of a transverse wave on a wire under tension is given by the formula: velocity = sqrt(tension / linear density) where tension is the tension force in the wire and linear density is the mass per unit length of the wire. We are given that the wire has a mass of 60 g and a length of 2 m, so its linear density is linear density = mass / length = 60 g / 2 m = 30 g/m We are not given the tension force in the wire, so we cannot find the exact velocity of the wave. However, we can use the given frequency and wavelength to find the closest value of the time for a crest of the wave to travel the length of the wire.

Using the formula for velocity and the given frequency and wavelength, we have: velocity = frequency x wavelength = 550 Hz x 0.7 m = 385 m/s Now, we can use this velocity to find the time for a crest of the wave to travel the length of the wire: time = length / velocity = 2 m / 385 m/s = 0.0052 s Therefore, the closest value of the time for a crest of the wave to travel the length of the wire is 0.0052 s. So, the time for a crest of this wave to travel the length of the 2-m wire is closest to 0.0052 seconds.

To know more about velocity  visit:

https://brainly.com/question/17127206

#SPJ11

397 Hz is the frequency of the sound wave in the pipe with length  216 cm and the air column in the pipe is vibrating and has five nodes

Define sound wave

The pattern of disruption brought about by the movement of energy through a medium (such as air, water, or any other liquid or solid matter) as it spreads away from the source of the sound is known as a sound wave. Pressure waves are generated by item vibrations that cause sound waves, such as those from a ringing phone.

The frequency of an occurrence is the number of times it repeats itself in a given amount of time. The frequency of wave-like patterns, such as sound, light, electrical signals, and other waves, expresses the number of cycles of the repeated waveform per second.

To learn more about sound wave use:

https://brainly.com/question/16093793

#SPJ4

To determine the location of the image in this scenario, we can use the thin lens equation, which is 1/f = 1/do + 1/di, where f is the focal length of the lens, do is the distance of the object from the lens,

and di is the distance of the image from the lens. We are given that the object is 10.0 cm to the left of the lens (i.e. do = -10.0 cm) and that the focal length of the lens is 16.0 cm.

Plugging these values into the thin lens equation, we get:

1/16.0 = 1/-10.0 + 1/di

Solving for di, we get:

di = (-1/1.6 + 1/-10.0)^-1

di = -6.67 cm

Therefore, the location of the image is 6.67 cm to the left of the lens (i.e. the image is virtual and located on the same side of the lens as the object).

It is important to note that the negative sign indicates that the image is virtual, which means that it cannot be projected onto a screen. Instead, it appears to be behind the lens when viewed from the same side as the object.

In summary, the location of the image is -6.67 cm.

To know more about 1/f = 1/do + 1/di refer here

https://brainly.com/question/10722312#

#SPJ11

The wavelength of an electron with energy 25 eV is approximately 5.35 x [tex]10^{-10}[/tex] meters.

To find the wavelength of an electron with energy 25 eV, we can use the de Broglie wavelength formula

λ = h/p

Where λ is the wavelength, h is the Planck constant (6.626 x [tex]10^{-34}[/tex] J*s), and p is the momentum of the electron.

The momentum of an electron with energy E can be found using the formula

p = √(2mE)

Where m is the mass of the electron.

Substituting the given values, we get

p = √(2(9.109 x [tex]10^{-31}[/tex] kg)(25 eV)(1.602 x [tex]10^{-19}[/tex] J/eV)) = 1.24 x [tex]10^{-24}[/tex]kg m/s

Now, we can calculate the wavelength

λ = h/p = (6.626 x [tex]10^{-34}[/tex] J*s)/(1.24 x [tex]10^{-24}[/tex]kg m/s) = 5.35 x [tex]10^{-10}[/tex] m

Therefore, the wavelength of an electron with energy 25 eV is approximately 5.35 x [tex]10^{-10}[/tex] meters.

To know more about wavelength here

https://brainly.com/question/10048980

#SPJ4

The doppler shift curves for exoplanet systems 51 Pegasi and Upsilon Andromedae are different in shape because they are caused by different phenomena. The doppler shift curve for 51 Pegasi is caused by the planet orbiting very close to its star, which causes the star's radial velocity to change rapidly and significantly. This creates a very pronounced curve with a steep slope.
On the other hand, the doppler shift curve for Upsilon Andromedae is caused by the gravitational interaction between two gas giant planets orbiting the same star. As the two planets orbit around the star, they pull on each other and cause their mutual orbits to shift slightly. This creates a more gentle curve with a smoother slope.
Overall, the shapes of these doppler shift curves are influenced by factors such as the mass, distance, and orbital characteristics of the planets in the system, as well as the distance between the planet and its star.
 The Doppler shift curves for the exoplanet systems 51 Pegasi (top) and Upsilon Andromedae (bottom) are different in shape mainly due to differences in their orbital parameters and the properties of the planets and stars involved.
For 51 Pegasi, the exoplanet has a short orbital period and is closely orbiting a sun-like star. This causes the Doppler shift curve to have a simple, periodic sinusoidal shape.
In contrast, the Upsilon Andromedae system has multiple exoplanets with varying orbital periods and distances from the star. This results in a more complex Doppler shift curve due to the combined gravitational influences of the multiple planets on the star's radial velocity.
In summary, the differences in shape of the Doppler shift curves for 51 Pegasi and Upsilon Andromedae are mainly attributed to the differences in their planetary system configurations and the properties of the planets and stars involved.

To know more about Doppler shift visit:

https://brainly.com/question/15427494

#SPJ11

The femur of the runner compresses by 0.0006 m when the normal force of the ground on the foot reaches three times the runner's body weight.

Given:

Length of the femur, L = 52 cm = 0.52 m

Mass of the runner, m = 79 kg

Cross-sectional area of the bone of the femur, A = 5.2 x 10⁻⁴m²

Young's modulus of the bone of the femur, Y = 1.6 x 10¹⁰ N/m²

The force exerted on the foot when it strikes the pavement, F = 3mg

The stress on the bone can be calculated as:

Stress = Force / Area

Stress = 3mg / A

The strain on the bone can be calculated as:

Strain = Stress / Young's modulus

Strain = (3mg / A) / Y

The change in length of the femur, ΔL, can be calculated as:

ΔL = Strain x Length

ΔL = [(3mg / A) / Y] x L

Substituting the given values, we get:

ΔL = [(3 x 79 x 9.81) / (5.2 x 10⁻⁴ x 1.6 x 10¹⁰)] x 0.52

ΔL ≈ 0.0006 m

Therefore, the femur of the runner compresses by 0.0006 m when the normal force of the ground on the foot reaches three times the runner's body weight.

Learn more about “normal force“ visit here;

https://brainly.com/question/30436126

#SPJ4

A. The impedance of the RLC circuit 50.08 Ω, B The rms current can be calculated using the equation 1.79 A. and The average power delivered to the circuit can be calculated using the equation 178.5 W.

A circuit is a closed path that allows electricity to flow from one point to another. It is composed of various electrical components, such as resistors and capacitors, that together form a complete electrical system. Circuits are used in a wide range of applications, from powering a simple light bulb to controlling complex machines in industrial settings.

(a) The impedance of the RLC circuit can be calculated using the equation Z = √(R2 + (Xc - Xl)2). Here, Xc = 1/(2πfC) and Xl = 2πfL. Therefore,
Z = √(502 + (1/(2π(350)(25.0e−3)) - 2π(350)(0.2))2)
= √(502 + (1.0044 - 28.27)2)
= √(2501.7525)
= 50.08 Ω
(b) The rms current can be calculated using the equation I = V/Z = (90.0)/50.08 = 1.79 A.
(c) The average power delivered to the circuit can be calculated using the equation P = I2R = (1.79)2(50) = 178.5 W.

To learn more about circuit
https://brainly.com/question/2969220
#SPJ4

The new force of attraction between the two objects would be 1.78 units.

Force is an influence that causes an object to change its velocity, shape or direction. Forces can be categorized into contact forces and non-contact forces. Contact forces are those that require physical contact between two objects, such as a person pushing a box, while non-contact forces are those that act without physical contact, such as gravity or magnetism. Forces can also be described as either balanced or unbalanced.

The force of attraction between two objects is inversely proportional to the square of the distance between them. This means that if the distance is tripled, then the force of attraction will be reduced to one ninth of its original value. Therefore, the new force of attraction between the two objects is 16/9 = 1.78 units.

To learn more about force

brainly.com/question/12970081

#SPJ4

Answer:

it will be in rotational equilibrium and not able to acquire angular acceleration

Your apparent weight is equal to your weight in an elevator not accelerating.

Apparent weight refers to the force a person feels due to gravity and any other forces acting on them, such as the normal force (the force exerted by a surface that supports an object).

1. In an elevator accelerating upwards: Your apparent weight is greater than your actual weight. This is because the upward acceleration adds to the gravitational force, making you feel heavier.

2. In an elevator in free fall: Your apparent weight is zero. This is because there is no normal force acting on you since the elevator is in free fall, which means you experience weightlessness.

3. In an elevator accelerating downwards: Your apparent weight is less than your actual weight. This is because the downward acceleration is working against the force of gravity, making you feel lighter.

4. In an elevator not accelerating Your apparent weight is equal to your weight because the normal force acting on you is equal to the force of gravity. When the elevator is not accelerating, there is no additional force affecting your apparent weight, so it remains equal to your actual weight.

To know more about accelerating  visit:

brainly.com/question/3046924

#SPJ11

Explanation:

force or gravitational force

To determine the corresponding values of the mean velocity (um) and mean temperature (tm), we first need to measure the velocity and temperature at different points in the fluid. We can then calculate the mean velocity and temperature using these measurements.



The mean velocity (um) is the average velocity of the fluid over a given area. It is calculated by dividing the total volume flow rate by the cross-sectional area of the flow. The mean temperature (tm) is the average temperature of the fluid over a given area. It is calculated by taking the average of the temperature measurements at different points in the fluid.

To plot the velocity and temperature distributions, we need to measure the velocity and temperature at different points in the fluid and plot them on a graph. We can then connect the data points to get a visual representation of the distribution.

Whether or not the values of um and tm appear reasonable will depend on the specific system being studied. We would need to compare our results to previous studies or theoretical models to determine if our values are reasonable.

learn more about velocity and temperature

https://brainly.com/question/30731456

#SPJ11

If our star (the Sun) shrinks into a black hole, the orbit of the planets of the solar system would remain same.

What is the planets' gravitational law?

A more precise formulation of the law is "Whenever one body exerts force upon a second body, the second body exerts an equal and opposite force upon the first body." That is, when a planet pulls on the sun with gravity, the planet pulls on the sun with a force that is comparable in strength.

A star the size of our Sun cannot become a black hole. However, if a black hole of the same mass appeared overnight to replace the Sun, the Solar System would remain intact. The gravitational attraction of a solar-mass black hole would be equal to that of the Sun. The planets would actually keep moving forward in their orbits.

To learn more about gravity, use:

https://brainly.com/question/940770

#SPJ4

The correct statement is B. The equivalent capacitance of the circuit is the sum of the individual capacitances.

When capacitors of unequal capacitance are connected in series, the total charge on each capacitor is the same, but the voltage across each capacitor is different. The voltage across each capacitor is inversely proportional to its capacitance, meaning that the capacitor with the largest capacitance will have the smallest voltage across it, and the capacitor with the smallest capacitance will have the largest voltage across it. The equivalent capacitance of the circuit is the reciprocal of the sum of the reciprocals of the individual capacitances. Therefore, the total capacitance is the sum of the individual capacitances. The voltage supplied by the battery is divided among the capacitors, with the voltage across each capacitor depending on its capacitance. Therefore, statement B is true.

Learn more about voltage here:

https://brainly.com/question/13521443

#SPJ11

When using a fume hood with a vertically opening sash, the best statement to describe the protection afforded when the sash is fully open is that the fume hood still offers protection in the case of an explosion but almost no protection from harmful gases.

It's important to remember that a fume hood is designed to protect the user from harmful chemicals and vapors, but it's not intended to provide protection in the event of an explosion. If an explosion were to occur, the fume hood would provide some level of protection by containing the blast and directing it away from the user.

However, harmful gases may still be released and could potentially pose a danger to the user. Therefore, it's important to always use proper safety procedures and follow the instructions for using a fume hood to minimize the risk of accidents and incidents.

To know more about gases visit :-

https://brainly.com/question/6140407

#SPJ11

The amount of electric current required to transport a certain number of electrons in a given time depends on the charge of each electron and the time interval over which they are transported.

Electrochemical cells are devices that convert chemical energy into electrical energy or vice versa. They typically consist of two electrodes, one anode and one cathode, which are connected by an electrolyte solution. The anode is the electrode where oxidation occurs, and it loses electrons to the electrolyte. The cathode is the electrode where reduction occurs, and it gains electrons from the electrolyte.Energy is a fundamental aspect of our everyday lives, and we use it to power everything from our homes and cars to our electronic devices and appliances. The laws of thermodynamics govern the behavior of energy in physical systems, and they tell us that energy cannot be created or destroyed, only converted from one form to another. This means that although we can transform energy from one form to another, the total amount of energy in a closed system remains constant.In summary, energy is a fundamental concept in physics that refers to the ability of a system to do work, and it is a crucial aspect of our daily lives, powering everything from our bodies to the machines and technology we use.

To know more about energy visit:

https://brainly.com/question/1932868

#SPJ11

The temperature of the colder reservoir is 140 K. so the answer will be none of the above (140 K).

The efficiency of an ideal Carnot engine is given by the formula:
efficiency = 1 - Tc/Th
where Tc is the temperature of the colder reservoir and Th is the temperature of the warmer reservoir. We are given that the engine extracts Qh = 300 J of heat from the warmer reservoir and does W = 200 J of work during each cycle. Using the first law of thermodynamics, we know that Qh = W + Qc, where Qc is the heat released to the colder reservoir. Therefore, Qc = Qh - W = 300 J - 200 J = 100 J.
Using the efficiency formula, we can solve for Tc:
efficiency = 1 - Tc/Th
0.4 = 1 - Tc/233 K
Tc/233 K = 0.6
Tc = 0.6 x 233 K = 140 K

To learn more about efficiency, click here:
https://brainly.com/question/31430273

#SPJ11

Explanation:

F =  9/5 C +32  

  9/5 ( 38.5) + 32 = 101.3 F  

The patient's temperature (38.5 °) in degrees Fahrenheit is 101.3 °F.

To convert a temperature from degree Celsius to degrees Fahrenheit, you can use the following formula: (Celsius * 9/5) + 32. In this case, the patient's temperature is 38.5 °C.

Applying the formula, we have: (38.5 * 9/5) + 32. Firstly, calculate 38.5 multiplied by 9/5, which is 69.3. Then, add 32 to this value: 69.3 + 32 = 101.3.

Therefore, the patient's temperature in degrees Fahrenheit is 101.3 °F. This conversion allows medical professionals to understand and compare temperatures in different units, ensuring appropriate care for the patient.

Learn more about Fahrenheit here: https://brainly.com/question/26141817

#SPJ11

The columns containing the most useful information for estimating the density of object C are the columns indicating whether it floats in liquids 1 and 3.

What is Density?

The density of a substance can be calculated by dividing its mass by its volume. The resulting value represents the amount of mass in a given volume of the substance. For example, a substance with a density of 1 g/cm³ would have a mass of 1 gram per cubic centimeter of volume.

Comparing the buoyancy of objects A, B, and C in liquids 1 and 3, we can see that object C floats in liquid 1 while objects A and B sink. This suggests that the density of object C is lower than that of liquids 2, 3, and 4. Similarly, in liquid 3, object C floats while objects A and B sink, indicating that the density of object C is lower than that of liquids 2, 4, and also lower than that of liquid 1.

Learn more about Density from the given link

https://brainly.com/question/26364788

#SPJ4

According to the National Highway Traffic Safety Administration (NHTSA), children must ride in a federally approved safety or booster seat in the rear of the vehicle until they are at least 8 years old or until they reach a height of 4 feet 9 inches (145 cm), whichever comes first.

The National Highway Traffic Safety Administration (NHTSA) is the agency within the U.S. Department of Transportation that works to reduce deaths and injuries and economic costs due to motor vehicle crashes. NHTSA works to deliver safer roads by encouraging Americans to make safer choices when they drive, ride, and walk; advancing lifesaving vehicle safety technologies; and supporting state and local police in their efforts to enforce the rules of the road that protect us all. By researching new vehicle safety technologies, mandating their inclusion on new vehicles, and rooting out defects in vehicles and equipment, NHTSA helps protect Americans when they’re on the road. NHTSA conducts research on how vehicle improvements and other technological advances can better protect people in a crash (crashworthiness) and reduce the likelihood of crashes (crash avoidance).

To know more about vehicle safety please visit

https://brainly.com/question/31839772

#SPJ11

Barred spirals are a type of galaxy that have a bar-shaped structure running through their centers, while ordinary spirals have a central bulge and arms that spiral outwards. Based on observations, it's estimated that roughly 30-35% of spiral galaxies are barred, with the remaining 65-70% being ordinary. However, it's important to note that these percentages may not be completely accurate, as different studies may define and identify barred spirals differently. Additionally, the overall number of galaxies in the universe is still uncertain and difficult to estimate, but current estimates suggest that there may be around 2 trillion galaxies in the observable universe alone.
Hi! Barred spiral galaxies and ordinary spiral galaxies are two distinct types of galaxies found in the universe. Barred spirals have a central bar-shaped structure, while ordinary spirals do not.

In general, it is estimated that about two-thirds of spiral galaxies in the universe are barred spirals, while the remaining one-third are ordinary spirals. This indicates that barred spirals are more common than ordinary spirals in the universe.

To know more about Barred spirals visit:

brainly.com/question/24420400

#SPJ11

An electron travels due north through a vacuum in a region of uniform magnetic field 4 that is also directed due north. It will: be unaffected by the field.

Electron is an open source library developed by GitHub that allows for the development of cross-platform desktop applications using web technologies such as HTML, JavaScript, and CSS. Electron applications are built with web technologies but have access to native operating system functionalities such as file system access and native notifications. Electron applications can be distributed through the Mac App Store, Windows Store, and Linux distributions such as Ubuntu and Fedora. Electron applications are designed to work on multiple platforms and provide a single codebase for developers looking to develop applications for multiple platforms. Electron applications are fast, secure, and user friendly, providing users with an intuitive interface and a seamless experience. Electron is a powerful tool for creating native applications that can be used on multiple platforms.

To learn more about electron

https://brainly.com/question/13380972

#SPJ4

The power series expansion of the principal branch of the log function about the point z = i is .:

Log(z) = iπ/2 + (z-i)/i - (z-i)²/2i² + (z-i)³/3i³

The logarithm function is described as  the inverse function to exponentiation which means the logarithm of a number x to the base b is the exponent to which b must be raised to produce x.

We will then apply  the formula for the derivative of the principal branch of the log function:

d/dz Log(z) = 1/z

Log(z) = Log(i) + (z-i)/i - (z-i)²/2i² + (z-i)³/3i³

where Log(i) =  the value of the principal branch of the log function at z = i.

So therefore Since Log(i) = ln(1) + iπ/2 = iπ/2,

Next step is to simplify the power series expansion :

Log(z) = iπ/2 + (z-i)/i - (z-i)²/2i² + (z-i)³/3i³

Learn more about the log function at:

https://brainly.com/question/13473114\

#SPJ1

When a large parallel-plate capacitor is being charged, the electric field between the plates increases at a rate of (dE/dt).

According to Maxwell's equations, particularly the Ampere-Maxwell law, a changing electric field generates a magnetic field (B) in the region between the plates.

For the charging capacitor, the magnetic field (B) will form closed loops around the edges of the plates.

The direction of the magnetic field can be determined using the right-hand rule, with your thumb pointing in the direction of the increasing electric field (from the positive plate to the negative plate), and your curled fingers indicating the direction of the magnetic field.

In summary, during the charging process of a parallel-plate capacitor, the increasing electric field (dE/dt) will induce a magnetic field (B) between the plates.

The magnetic field will form closed loops around the edges of the plates, with the direction determined by the right-hand rule.

For more information on electric field kindly visit to

https://brainly.com/question/19952765

#SPJ11

A. the light to reach us, so we would see it disappear 6.72 x 10⁷ years from now, B. the time interval is 8 minutes. and C. the time interval is 2.5 seconds.

Light is a form of energy that is visible to the human eye. It exists in many forms, such as natural light from the sun, artificial light from a light bulb, and even invisible forms such as X-rays and ultraviolet-radiation. Light is made up of tiny particles called photons which are produced when an atom is excited by heat or electricity.

(a) If Polaris were to burn out today, it would take approximately 6.44 3 10¹⁸ m divided by the speed of light (3.0 x 10⁸ m/s) which equals 2.14 x 10¹⁰ seconds (or 6.72 x 10⁷ years) for the light to reach us, so we would see it disappear 6.72 x 10⁷ years from now.

(b) The time interval required for sunlight to reach the Earth is about 8 minutes. This is because the distance from the Sun to the Earth is about 1.5 x 10⁸ km, and
the speed of light is 3.0 x 10⁸ m/s,
so the time interval is approximately 1.5 x 10⁸ km / 3.0 x 10⁸ m/s = 8 minutes.

(c) The time interval required for a microwave signal to travel from the Earth to the Moon and back is about 2.5 seconds.
This is because the distance from the Earth to the Moon is about 3.84 x 105 km, and the speed of light is 3.0 x 10⁸ m/s,
so the time interval is approximately 3.84 x 10⁵ km / 3.0 x 10⁸ m/s = 2.5 seconds.

To learn more about light

https://brainly.com/question/104425

#SPJ4

The speed of the skier on reaching the bottom of the slope. The answer is B) 31 m/s.

To solve this problem, we can use the conservation of energy principle. Initially, the skier has only potential energy, which is given by mgh, where m is the mass of the skier, g is the acceleration due to gravity (9.8 m/s^2), and h is the height of the slope (50 m). When the skier reaches the bottom of the slope, all of this potential energy is converted to kinetic energy, which is given by (1/2)mv^2, where v is the velocity of the skier.

Setting these two equations equal to each other, we have:

mgh = (1/2)mv^2

Simplifying, we get:

v = sqrt(2gh)

Substituting the given values, we have:

v = sqrt(2 x 9.8 m/s^2 x 50 m) = 31 m/s

Therefore, the answer is B) 31 m/s.

It's important to note that neglecting friction is an idealized assumption, as frictional forces are present in most real-world situations. However, this assumption is often made in physics problems to simplify the calculations and focus on the main concepts.

To know more about skier click here:

https://brainly.com/question/1503665

#SPJ11

Between Mars and Jupiter's orbits is where the asteroid belt is located. Because of orbital resonances with Mars, it exists. Here option B is the correct answer.

The asteroid belt is a region in our solar system that contains numerous small celestial bodies known as asteroids, with some as large as 590 miles (940 kilometers) in diameter. It is located between the orbits of Mars and Jupiter, with an average distance of about 280 million miles (450 million kilometers) from the Sun.

The asteroid belt exists because of gravitational interactions with Jupiter, which prevented the formation of a planet between Mars and Jupiter. However, the asteroids in the belt are not in stable orbits and can be perturbed by the gravitational influence of other planets, leading to collisions and ejections from the belt.

In particular, the asteroid belt's location and shape are strongly influenced by orbital resonances with Mars. Orbital resonance occurs when two objects orbiting the Sun exert a regular gravitational influence on each other, causing their orbits to be synchronized. As Mars orbits the Sun, it exerts a regular gravitational pull on the asteroids in the belt, causing them to follow specific orbital patterns.

To learn more about asteroid belt

https://brainly.com/question/25531422

#SPJ4

Complete question:

Choose the correct explanation, where is the asteroid belt located, and why.

A - The asteroid belt lies between the orbits of Jupiter and Saturn. It exists because of orbital resonances with Jupiter.

B - The asteroid belt lies between the orbits of Mars and Jupiter. It exists because of orbital resonances with Mars.

C - The asteroid belt lies between the orbits of Jupiter and Saturn. It exists because of orbital resonances with Saturn.

D - The asteroid belt lies between the orbits of Mars and Jupiter. It exists because of orbital resonances with Jupiter.

The distance separating the objects is doubled, then the new force is 0.02 N.

Distance is a numerical measurement of how far apart two objects or locations are. It is a scalar quantity, meaning it can be expressed in terms of a single numerical value without any associated direction.

The force between two charged objects is given by Coulomb's law:

F = k×(q¹×q²)/r²

where k is the Coulomb's constant, q¹ and q² are the charges of the two objects, and r is the distance between them.

In the given problem, the force between the two objects is 0.080 N. This means that: 0.080 N = k×(q¹×q²)/r²

Now, if the charge of one of the objects is increased by a factor of four, and the distance separating the objects is doubled, then the new force will be given by: F' = k×(4×q²)/(2×r)²

Substituting the original values of k, q², and r in the above equation, we get: F' = 0.080×(4)/(2×r)²

F' = 0.080×(4)/(4×r²)

F' = 0.080/r²

F' = 0.080/4×r²

F' = 0.02 N

Therefore, the new force between the two charged objects is 0.02 N.

To learn more about distance

https://brainly.com/question/26550516

#SPJ4