Answer:
h = 4.25 m
Explanation:
[tex]gravitational \space\ potential \space\ energy \space\ (gpe)= m g h\\[/tex] ,
where m is the mass, g is acceleration of gravity, and h is height of object.
In our case, m = 1.2 kg, g = 9.8m/s², and gpe = 50 J.
50 = 1.2 x 9.8 x h
h = 50 / (1.2 x 9.8)
h = 4.25 m
Answer:
4.25m
Explanation:
Joules is a "derived unit", meaning it is really composed of other units, and it is just abbreviated as a single letter.
[tex]1[J]=1 [\frac{kg \cdot m^2}{s^2}][/tex]
This comes from the formula for potential energy, often denoted "U"
[tex]U=mgh[/tex], where m is the mass of the object (measured in kilograms, [tex]kg[/tex]), g is the acceleration due to gravity at that spot (measured in meters per second squared, [tex]\frac {m}{s^2}[/tex]), and h is the height of the object (measured in meters, [tex]m[/tex]).
Note: The object itself may or may not have an acceleration of "g" at the given point because it may be supported (like on a bookshelf). However, the "g" is representative of its gravitational acceleration at that point if gravity could accelerate it unimpeded.
Rearranging the potential energy equation to isolate the unknown "h", dividing both sides by "m" and "g", we get the following:
[tex]\dfrac{U}{mg}=h[/tex]
Substituting known values (and rewriting Joules as its SI units so we can ensure units cancel the way we need them to):
[tex]\dfrac{\left (50 [\frac{kg \cdot m^2}{s^2}] \right)}{(1.2 [kg])(9.8 [\frac{m}{s^2}])}=h\\\dfrac{\left (50 [\frac{kg \!\!\!\!\!\!\!{--} \cdot m^{2 \!\!\!{-}}}{s^2\!\!\!\!\!\!\!{--} }] \right)}{(1.2 [kg \!\!\!\!\!\!\!{--} ])(9.8 [\frac{m\!\!\!\!\!\!\!{--} }{s^2\!\!\!\!\!\!\!{--} }])}=h\\\dfrac{(50)}{(1.2)(9.8)}[m]=h\\\\4.2517[m] \approx h[/tex]
Thus, the height of the book would be approximately 4.25meters high.
The reason galaxies that are distant from our galaxy move away from our galaxy more rapidly than those that are near is:
The reason galaxies that are distant from our galaxy move away from our galaxy more rapidly is more space expands between us and distant galaxies.
What is a galaxy?A galaxy is a group of millions of stars and their systems that are grouped due to gravitational forces.
According to the Big Bang theory, galaxies are expanding and separate among them.
In conclusion, the reason galaxies that are distant from our galaxy move away from our galaxy more rapidly is more space expands between us and distant galaxies.
Learn more about galaxies here:
https://brainly.com/question/13956361
#SPJ12
Answer:
the galaxies are moving as the universe keep expanding .
Explanation:
What are the characteristics of the image formed by the object?
Answer:
The image is formed by a convex lens with the object at 2F.
Image will be of same size as the objectImage will be real and upside down.Sample Response: The image created by the object is located on 2F behind the lens, real, inverted, and the same size as the actual object.
Explanation: EDGE.
what type of modulation does the omni-directional antenna transmit?
AM and FM are the two types of modulation that an omnidirectional antenna transmit.
What is an omnidirectional antenna?An omnidirectional antenna is also referred to as an isotropic antenna and it can be defined as a type of antenna that is designed and developed to radiate equal radio power or intercept radio-frequency (RF), especially in all directions perpendicular to an axis.
In Science, there are two types of modulation that an omnidirectional antenna transmit and this include the following:
Frequency modulation (FM).Amplitude modulation (AM).Read more on amplitude modulation here: https://brainly.com/question/10690505
#SPJ12
does anyone know this whole distance and displacement concept it makes zero sense
Answer:
Distance is the total length travelled, or in other words, it is a measure of how far apart two objects are.
Displacement, on the other hand, the difference between the starting and and ending positions of an object.
For example, if a person walks 10m forwards, then 7m backwards, thereby ending up where he started, he will have travelled a distance of
10 + 7 = 17m .
But the difference between his starting and finishing positions is
10 - 7 = 3m.
If, however, the man walked 10m forwards and then 10m backwards, the distance he covered would be 10 + 10 = 20m, but the displacement would've been 0 as there would be no difference between his starting and ending positions.
Let me know if you still don't understand.
The chart lists four different kinds of atoms.
A chart titled Different Kinds of Atoms with the entries calcium, gold, argon, iodine.
What is true about all of these atoms?
They cannot be solids.
They are the largest units of matter.
They are the only types of atoms that exist.
They cannot be divided and still keep the properties of the element.
They cannot be divided and still keep the properties of the element true about all of these atoms. Option D is corect.
What is an atom?The atom consists of matter that may be split without releasing electrical charges.
It's also the smallest unit of matter with chemical element features. As a result, the atom is the fundamental unit of science.
In the nucleus proton and the neutron is exists. The condition of the atom to be electrically neutral is that the number of the proton and electron should be the same.
They cannot be separated while still maintaining the element's characteristics for each and every one of these atoms.
Hence, option D is corect.
To learn more about the atom refer to the link;
https://brainly.com/question/1566330
#SPJ1
Answer:
The correct answer is d, they cannot be divided and still keep the properties of the element.
Explanation:
You're welcome :)
1) Two students are making their way to school. One has a bike and the other
is on foot. If the student on foot is going at a speed of 3 m/s and they make
it to school in 30 s, how far away was the school?
To find how far away the school is:
3m/s * 30 s = 90m
Hope it helps!
Q1.
(a) Some students have designed and built an electric-powered go-kart. After testing, the
students decided to make changes to the design of their go-kart.
First design X
Final design Y
The go-kart always had the same mass and used the same motor.
The change in shape from the first design (X) to the final design (Y) will affect the top
speed of the go-kart.
Explain why.
Answer:Because if the shape gets changed it will move faster without to much weight
Explanation:
The force exerted on the tires of a car that directly accelerate it along a road is exerted by the
The force exerted on the tires of a car that directly accelerate it along a road is exerted by the road friction.
What is force?Force is defined as the product of mass and acceleration of an object.
Friction is defined as the force that resists the movement of an object over another.
Therefore, the force exerted on the tires of a car that directly accelerate it along a road is exerted by the road friction.
Learn more about force here:
https://brainly.com/question/12970081
#SPJ12
durning which type of process does pressure remain consistent
A.Isothermal
B.isolated
C.Adiabatic
D.Isobaric
Answer:
[tex]\fbox {D. Isobaric}[/tex]
Explanation:
The process during which pressure remains constant is called an isobaric process.
If your mass is 63.7 kg, and you are standing 7.5 m away from a boulder with
a mass of 9,750.6 kg, what is the gravitational force between you and the
boulder? Newton's law of gravitation is F
Gm m₂. The gravitational
=
gravity
constant G is 6.67 x 10-11 N-m²/kg².
A. 1.10 x 104 N
B. 7.37 x 10-7 N
C. 9.82 x 10-8 N
D. 5.52 x 10-6 N
Please help me!
Answer:
B
Explanation:
F=[tex]\frac{Gm1m2}{r^2}[/tex]
F=(6.67 x 10^-11)[tex]\frac{63.7X9,750.6}{7.5^2}[/tex]
F=7.36502254e-7
Discuss the path that light takes through the human eye
The cornea is shaped like a dome and bends light to help the eye focus. Some of this light enters the eye through an opening called the pupil (PYOO-pul). The iris (the colored part of the eye) controls how much light the pupil lets in. Next, light passes through the lens (a clear inner part of the eye).
A body at rest is given an initial uniform acceleration of 8m/s2 for 30s after which the acceleration is reduced to 5m/s2 for the next twenty seconds. The body maintains the speed attained for 60s, after which it is brought to rest in 20s.
Explanation:
v=u+at, where v,u,a and t are the final velocity, initial velocity, acceleration and time, respectively.
For t=0 s to t=30 s , a =8 m/s 2.
For t=30 s to t=50 s , a = 5 m/s 2.
For t=50 s to t=110 s , a = 0 m/s 2.
For t=110 s to t=130 s , a is such that the body comes to rest at the end of this period.
For t=0 s to t=30 s ,v=0+8t⇒v=8t m/s.
At t=30s,v=8×30=240 m/s.
For t=30 s to t=50 s ,v=240+5(t−30)⇒v=90+5t m/s
At t=50s,v=90+5×50=340 m/s.
For t=50 s to t=110 s ,v=340 m/s.
For t=110 s to t=130 s ,v=340+a(t−110).
The body comes to a halt at t=130 s ⇒0=340+a(130−110).
0=340+20a⇒a=−34020=−17 m/s2.
For t=110 s to t=130 s ,v=340−17(t−110)=2210−17t m/s.
as time passes the sound wave
Answer:
Loud to soft while pitch increases
Explanation:
Sound waves shown graphically display their amplitude (height of the graph) and their wavelength (the horizontal distance from peak to peak, or valley to valley... one full cycle).
Instead of wavelength, alternatively, one can observe the frequency of the wave (how many cycles are completed for a given unit of horizontal distance) which is in an inverse relationship with the wavelength (as a wavelength gets shorter, the frequency gets higher, and as the wavelength gets longer, the frequency gets lower).
The amplitude of a wave corresponds to how loud the sound is.
The frequency of a wave corresponds to the pitch of the sound.
Notice that on the graph, the height of the graph decreases over time (the peaks get shorter and shorter). So, the sound volume will get quieter and quieter. Using terminology that matches the answer choices, the sound will start loud and get soft.
Notice that on the graph, the wavelength decreases over time (starts with a pretty long distance between peaks, and then the distance between peaks gets shorter and shorter). Alternatively, looking at frequency, notice that the frequency gets higher and higher (on the left, one finger-width doesn't is less than one full cycle, but on the right, the same finger-width is wider than multiple cycles). So, the pitch of the sound will get higher and higher.
Thus, for this graph, the sound goes from loud to soft, and the pitch increases.
please answer this fast
I 'll marks them brainliest answer
answer
64 is C (c) 1-Bromo-3-methylbutane
63 is D
i is secondary ii is primary
what is the speed of a wave that has a frequency of 11.5Hz and a wavelength of 1.7m?
Answer:
19.55 m/s
Explanation:
Here is HOW to get the answer:
Speed = wavelength * freq
= 1.7 * 11.5 = 19.55 m / s
How to add two on/off switches that can change the brightness of the light in circuit a without turning it off
Answer:
ressistor
Explanation:
Now, let's look at how the distance from the charge affects the magnitude of the electric field. Select Values on the menu, and then click and drag one of the yellow E-Field Sensors. You will see the magnitude of the electric field given in units of V/m (volts per meter, which is the same as newtons per coulomb). Place the E-Field Sensor 1 m away from the positive charge (1 m is two bold grid lines away if going in a horizontal or vertical direction), and look at the resulting field strength. Consider the locations to the right, left, above, and below the positive charge, all 1 m away. For these four locations, the magnitude of the electric field is________________. the same. greatest to the left of the charge. greatest below the charge. greatest to the right of the charge. greatest above the charge.
Electric field strength decreases as the distance from the source increases.
How the distance from the charge affects the magnitude of the electric field?The strength of an electric field is inversely related to square of the distance from the source. This means that the electric field strength decreases when the distance from the source increases.
So we can conclude that Electric field strength decreases as the distance from the source increases.
Learn more about source here: https://brainly.com/question/25578076
#SPJ12
a protostar will continue to collapse due to gravity until it reaches the main sequence, and then gravitational collapse will stop when _____ begins.
a protostar will continue to collapse due to gravity until it reaches the main sequence, and then gravitational collapse will stop when fusion of hydrogen begins.
What is a protostar and how does gravity affect it?A protostar serves as a very young star which is very small in mass and still developing its mass from parent molecular cloud.
However, it can be affected by gravity because , when there is not collapse on the gravity, if there is fusion of hydrogen begins in it.
Learn more about gravitational collapse on:
https://brainly.com/question/25624188
#SPJ11
The ball is in contact with the bat for 0.001s use the equation in the box to caluclate the force exerted by the bat on the ball
Answer:
Force = 9600N
Explanation:
If this is the right question, there should have been a question before about the what the change in the momentum of the ball was. The answer to that was 9.6kg m/s. For this part, we divide this by the time taken which was 0.001s which give us the resultant force.
resultant force = change in momentum ÷ time
= 9.6kgm/s ÷ 0.001s
= 9600N
An object has a mass of 8.0 kilograms. a 2.0-newton force moves the object a distance of 3.0 meters to the east, and then 4.0 meters to the north. what is the total work done on the object
Answer:
1. An object has a mass of 8.0 kilograms. A 2.-newton force displaces the object a distance of 3.0 meters to the east, and then 4.0 meters to the north. What is the total work done on the object? 1)10 J 2) 14 J 3) 28 J 4) 56 J I found the resultant of the two distances, which is 5 m, I used 5 m * 2 N=10 J, but it’s not the answer. 2. A 20-newton block is at rest at the bottom of a frictionless incline, since I can’t show you the diagram, I will describe it. Supposed a right triangle, the vertical height is 3 m, and the base is 4.0 m. Then the hypotenuse is the incline and the block is at the bottom. The question is: How much work must be done against gravity to move the block to the top of the incline? I know that conservative forces are forces for which the work done does not depend on the path taken but only on the initial and final positions. But here I Know I should use 3 m * 20N=60 J. but the thing is it starts from the bottom which is the bottom of the incline, and ends at the top, then it should be the length of the hypotenuse? But if it’s 3 m, then it should have started from left end of the base, not the right end of the base which is the bottom of the incline.
Reference: https://www.physicsforums.com/threads/what-is-the-total-work-done-on-the-object.241750/
help in solving this question please
(question is on the picture )
Answer:
Jesus
Explanation:
he is the way
a note of frequency 200Hz has a velocity of 400m/s. what is the wavelength of the note
Answer:
[tex]\huge\boxed{\sf \lambda = 2 m}[/tex]
Explanation:
Given data:Frequency = f = 200 Hz
Velocity = v = 400 m/s
Required:Wavelength = λ = ?
Formula:v = fλ
Solution:Put the givens in the formula
400 = (200)λ
Divide 200 to both sides
400/200 = λ
2 m = λ
λ = 2 m
[tex]\rule[225]{225}{2}[/tex]
The Voyager spacecraft is moving at 17 000 m/s. How far will it travel in one year? Give your answer in km.
Explanation:
first change m/s to km/hr and time 1 year to hour b/c we are asked the to give in km. so,
v=17,000 m/s = 17000×3600/1000 = 61,200 km/hr
t= 1 year= 365 days =365day×24 hr/day = 8,760hr
therefore, V = s/t from this s = v×t =61200×8760 =536,112,000 Km
where do automatically generated statements that set the properties of the labels, buttons, and forms end up?
The generated statements that set the properties of the labels, buttons, and forms end up automatically within the InitializeComponent() method.
What is InitializeComponent?The InitializeComponent method in programming is the that have code that works with codes that creates and initializes the creates and initializes the user interface objects .
Conclusively, when a statement is generated, to when set the properties of the labels , it will definitely been felt in the InitializeComponent() method automatically.
Learn more about InitializeComponent() method on:
https://brainly.com/question/16783636
#SPJ11
im
Complete the sentence to describe what a wave is and what it does.
E§
A wave is a
that carries
from one place to another.
Hope this helps.
Good luck ✅.
The quotient of 8.4x10° and a number n results in 5.6x 1027. What is the value of n?
1.5x10-18
O 1.5x10
O 1.5x10³
1.5x10¹8
Avery sees a UFO out her bedroom window and calls to report it to the police. She says, "The UFO moved 20.0 m east, 10.0 m north, and 30.0 m west before it disappeared." What was the displacement of the UFO while Avery was watching?
Answer:
10^2 + 10^2 = x^2
x = 14.2 m NW
A particle moves along a straight line such that its acceleration is a=(4t^2-2)
The velocity of the particle moving along the straight line at any time, t is determined as v = 4t³/3 - 2t + C.
What is the velocity of the particle?
The velocity of an object is the rate of change of displacement with time. It is also the integral of acceleration of the object.
a = 4t² - 2
v = ∫a
v = 4t³/3 - 2t + C
Thus, the velocity of the particle moving along the straight line at any time, t is determined as v = 4t³/3 - 2t + C.
Complete question:
A particle moves along a straight line such that its acceleration is a=(4t^2-2). Find its velocity at any time, t.
Learn more about velocity here: https://brainly.com/question/6504879
#SPJ12
1.) Identify one component of the visible spectra
2.) identify the component of the electromagnetic spectra that has the shortest wavelength
Answer:
1.) color
2.) Gamma Rays
Explanation:
what evidence would you expect to find on the moon if it had been subjected to plate tectonics? (select all that apply.)
Volcanoes and mountains are the evidences that show plate tectonics.
What evidence would you expect to find on the Moon if the Moon had been subjected to plate tectonics?The presence of volcanos and mountains are the evidences that provides information that the moon has plate tectonic. If there is no volcanoes and mountains on the moon then we can say that there is no plate tectonic on the moon.
So we can conclude that volcanoes and mountains are the evidences that show plate tectonics.
Learn more about tectonics here: https://brainly.com/question/2325633
#SPJ11
