The output of the system is given as:$$\begin{aligned}y(t) &= x(t)*h(t) \\ &= \int_{-\infty}^{\infty}x(\tau)h(t-\tau)d\tau \\ &= \int_{0}^{t}-2(3)d\tau + \int_{2}^{t}-2(3)d\tau + \int_{3}^{t}-2(3-3)d\tau \\ &= -6t + 24 \end{aligned}$$
Given the impulse response, h(t) = 3 x {u(t) – u(t – 2)} and input signal, x(t) = -2 * {u(t) – u(t – 3)}
(i) Sketch the waveforms of x(t) and h(t), respectively: Waveform of x(t) is given below: Waveform of h(t) is given below:
(ii) System properties:
Memory: The system is non-memory system, as the output depends only on the present value of input.
Causality: The system is causal as the output depends only on the present and past values of the input.
Stability: A system is said to be stable if its impulse response is absolutely integrable.
Let us check for stability of given system below: $$\begin{aligned}\int_{-\infty}^{\infty}|h(t)|dt &= \int_{-\infty}^{0}|h(t)|dt + \int_{0}^{2}|h(t)|dt + \int_{2}^{\infty}|h(t)|dt \\ &= \int_{0}^{2}3dt \\ &= 6 \end{aligned}$$
Thus the given system is stable.
(iii) Sketch the waveform of the output signal y(t):
The output of the system is given as:$$\begin{aligned}y(t) &= x(t)*h(t) \\ &= \int_{-\infty}^{\infty}x(\tau)h(t-\tau)d\tau \\ &= \int_{0}^{t}-2(3)d\tau + \int_{2}^{t}-2(3)d\tau + \int_{3}^{t}-2(3-3)d\tau \\ &= -6t + 24 \end{aligned}$$
To know more about output visit:
brainly.com/question/33452860
#SPJ11
37:45 Tune Remaining Return Next 196 points Consider the
first-order circuit below. Starting with some initial voltage, the
capacitor voltage (after the switch is closed)
is given by tc (t) 18-Vfort > 0. Then the values of the resistors R₁ and R₂
consistent with this information are
1=0 s ww R₁ VC 24 V + هم www R₂ 13
The expression for vc(t) given in the problem matches this expression, so the values of R1 and R2 are
R1 = C
R2 = Vf/C. The correct answer is (A).
The given circuit is a first-order RC circuit, with a switch that is closed at time t=0. The capacitor voltage is given by the equation:
Code snippet
vc(t) = 18 - et * Vf, t > 0
Use code with caution. Learn more
where Vf is the voltage across the capacitor at time t=0.
The circuit can be redrawn as follows:
The voltage across the capacitor is given by:
vc(t) = C * dvc/dt
Use code with caution. Learn more
Substituting the expression for vc(t) into this equation, we get:
C * dvc/dt = 18 - et * Vf
Use code with caution. Learn more
This equation can be solved to find the expression for vc(t):
vc(t) = 18 - Vf * (1 - et)/C
Use code with caution. Learn more
The expression for vc(t) given in the problem matches this expression, so the values of R1 and R2 are:
R1 = C
R2 = Vf/C
So, the correct answer is (A).
Learn more about expression here
https://brainly.com/question/14469911
#SPJ11
Which of the following statements is false: a. For an n-type semiconductor, electron is present in the greater concentration. b. For a p-type semiconductor, hole is present in the greater concentration. c. For the extrinsic semiconductors, their overall charge is neutral. d. In order for a semiconductor to exhibit extrinsic electrical characteristics, relatively high impurity concentrations are required.
The false statement among the following statements is d. In order for a semiconductor to exhibit extrinsic electrical characteristics, relatively high impurity concentrations are required.
Semiconductors are the substances whose conductivity lies between that of conductors and insulators. It is possible to increase the conductivity of semiconductors by introducing impurities into the pure semiconductor crystal. This process is known as doping. The two types of disable semiconductors are n-type semiconductor and p-type semiconductor. Here, the given statements are:
a. For an n-type semiconductor, electron is present in the greater concentration: It is true that an n-type semiconductor is formed by doping a pure semiconductor crystal with a pentavalent impurity element such as phosphorus (P), arsenic (As), or antimony (Sb). These impurity atoms have 5 valence electrons in their outermost shell. As a result, when they are introduced into a pure semiconductor crystal such as silicon (Si) or germanium (Ge), they provide an extra electron, which increases the concentration of free electrons in the semiconductor. Therefore, statement (a) is true.
b. For a p-type semiconductor, hole is present in the greater concentration: It is also true that a p-type semiconductor is formed by doping a pure semiconductor crystal with a trivalent impurity element such as boron (B), aluminum (Al), or gallium (Ga). These impurity atoms have only 3 valence electrons in their outermost shell. As a result, when they are introduced into a pure semiconductor crystal such as silicon (Si) or germanium (Ge), they create a hole in the valence band, which can be thought of as a vacancy of an electron. Therefore, statement (b) is true.
c. For the extrinsic semiconductors, their overall charge is neutral: It is true that the extrinsic semiconductors, which are formed by doping a pure semiconductor crystal with impurities, have an overall charge of neutrality because the number of negative charges (electrons) is equal to the number of positive charges (holes). Therefore, statement (c) is true.
d. In order for a semiconductor to exhibit extrinsic electrical characteristics, relatively high impurity concentrations are required: It is the false statement because even a very small concentration of impurities can significantly change the electrical conductivity of a semiconductor crystal. Therefore, statement (d) is false.
To know more about doping refer to:
https://brainly.com/question/15184439
#SPJ11
FILL THE BLANK.
Examining a map that depicts different colors based on flu outbreaks is an example of a digital ____________.
A. sql
B. transaction processing systems
C. support
D. operating system
E. dashboard
Examining a map that depicts different colors based on flu outbreaks is an example of a digital dashboard.
What is an example of a digital tool that presents information through a visual interface, such as a map displaying different colors based on flu outbreaks?Examining a map that depicts different colors based on flu outbreaks is an example of a digital dashboard.
A digital dashboard is a visual interface that displays key information and data in a consolidated and user-friendly manner.
It provides a real-time or near-real-time snapshot of various metrics and indicators relevant to a specific domain or purpose. In the given scenario, the map displaying different colors based on flu outbreaks serves as a digital dashboard as it presents data related to flu outbreaks in a visual and easily understandable format. Digital dashboards are commonly used in various fields, such as business intelligence, healthcare, and data analysis, to provide a quick overview and facilitate decision-making based on the presented information.
Learn more about Examining
brainly.com/question/28347366
#SPJ11
1. [Model Formulation of Linear Programming - Manufacturing] The Electrocomp Corporation manufactures two electrical products: air conditioners and large fans. The assembly process for each is similar in that both require a certain amount of wiring and drilling. Each air conditioner takes 5 hours of wiring and 6 hours of drilling. Each fan must go through 3 hours of wiring and 2 hours of drilling. During the next production period, 200 hours of wiring time are available and up to 120 hours of drilling time may be used. Each air conditioner sold yields a profit of $30. Each fan assembled may be sold for a $10 profit. Formulate this LP production-mix situation. (You do not have to solve this problem mathematically or using any software.)
(a) What are the Decision Variables?
(b) What is the Objective Function?
(c) What are Constraint Equations including non-negativity constraints?
Decision variables are the number of fans and air conditioners, the objective function is to maximize the profit, and constraints are available wiring and drilling hours.
In this manufacturing problem, the Electrocomp Corporation produces two electrical products: air conditioners and large fans. The assembly process for each product requires a certain amount of wiring and drilling. To formulate the linear programming (LP) problem, we need to identify the decision variables, the objective function, and the constraint equations.
Decision variables: Decision variables represent the quantities of the products to be produced. In this case, we use x to represent the number of air conditioners produced and y to represent the number of large fans produced.
Objective function: The objective is to maximize the profit. The profit for each air conditioner sold is $30, and the profit for each fan assembled is $10. Thus, the objective function can be written as: Profit = 30x + 10y.
Constraint equations: The constraints are based on the available wiring and drilling hours. The problem states that there are 200 hours of wiring time available and up to 120 hours of drilling time. The wiring constraint equation is given by 5x + 3y ≤ 200, which represents the total wiring hours used by producing x air conditioners and y large fans. The drilling constraint equation is 6x + 2y ≤ 120, which represents the total drilling hours used. Additionally, the variables x and y should be non-negative, as we cannot produce negative quantities of products: x ≥ 0 and y ≥ 0.
By formulating the LP problem in this way, we have established the decision variables, objective function, and constraint equations that will guide the optimization process to determine the optimal production mix of air conditioners and large fans.
Learn more about manufacturing here:
brainly.com/question/32717570
#SPJ11
6. Draw a differentiator and integrator of Op AMP and show their related gains (1 pt) 7. Please explain what super Diode is (1 pt)
Differentiator and Integrator of Op-Amp are circuits that are used to produce the mathematical operations of differentiation and integration respectively.
The Differentiator and Integrator of Op-Amp and their related gains are:
1. Differentiator CircuitThe Op-Amp Differentiator Circuit is shown in the below figure.
The Differentiator circuit configuration is shown above.
By analyzing the output waveform, we may see that it is nothing more than the differentiation of the input waveform, and the gain of the circuit is based on the relationship between the feedback resistance and the input resistance.
Gain of Differentiator = - Rf/R2
In the above circuit, when Vin is applied, the output is proportional to the rate of change of the input voltage with time, and since dV/dt of Vin is the rate of change of the input voltage with time, the output is proportional to the dV/dt of Vin.
Hence, the circuit acts as a Differentiator Circuit.
2. Integrator CircuitThe Op-Amp Integrator Circuit is shown in the below figure.
The Integrator circuit configuration is shown above.
By analyzing the output waveform, we may see that it is nothing more than the integration of the input waveform, and the gain of the circuit is based on the relationship between the feedback resistance and the input resistance.
Gain of Integrator = - Rf/R2
In the above circuit, when Vin is applied, the output is proportional to the integral of the input voltage with time, and since ∫Vin dt is the integral of the input voltage with time, the output is proportional to the ∫Vin dt of Vin.
Hence, the circuit acts as an Integrator Circuit.
7. Super Diode:A Super diode is a diode that is made up of an operational amplifier and a diode.
It acts as a voltage-controlled switch that has low forward voltage drop and high reverse voltage breakdown.
It is also known as an Ideal Diode. When the voltage at the non-inverting input is greater than the voltage at the inverting input, the output of the operational amplifier is high, and the diode is forward-biased.
When the voltage at the non-inverting input is lower than the voltage at the inverting input, the output of the operational amplifier is low, and the diode is reverse-biased, resulting in the current flowing through the feedback resistor.
To know more about output visit:
https://brainly.com/question/14227929
#SPJ11
The system function of a causal LTI system is given as H1(s)=2s + 5/s^2+5s+6
a) (2) Write down the differential equation relating the input x(t) and the output y(t).
b) (2) Determine the output y(t) when the input is x(t) = e-tu(t) is applied to Hi(s). = 20 (s+1) Another causal LTI system has the system function
H2(s) 20(s+1)/S2+45+2504
c) (2) Sketch the pole-zero plot.
d) (2) Specify the ROC. Explain your answer.
e) (2) Is the system stable? Explain your answer.
f) (2) What is the value of the natural frequency of this system? What is the value of its zeta parameter ?
g) (2) Is the system oscillatory ? Explain your answer.
h) (2) Is the system over-damped, under-damped or critically damped ? Explain your answer.
i) (2) Specify the maximum gain, the half-power gain and the half-power frequency / frequencies.
j) (2) Roughly sketch the magnitude response. Show important values.
If an input x(t) = 1 + 4 sin(52t) + 2 sin(1000t) is applied to this stable LTI system,
k) (2) Estimate the frequency response (in exponential form) at w = 0, w = 52 rad/s and w = 1000 rad/s.
l) (2) Represent the output y(t) as the sum of real sine signals
a) The differential equation relating the input x(t) and the output y(t) can be obtained by taking the inverse Laplace transform of the system function H1(s):
\[2\frac{d^2y(t)}{dt^2} + 5\frac{dy(t)}{dt} + 6y(t) = 2\frac{dx(t)}{dt} + 5x(t)\]
b) To determine the output y(t) when the input x(t) = e^(-t)u(t) is applied to H1(s), we can substitute s = -1 into the system function H1(s) and perform the inverse Laplace transform:
\[y(t) = 20e^{-t} - 20e^{-3t}\]
c) The pole-zero plot for the system with the system function H2(s) = 20(s+1)/(s^2+45s+2504) will have two poles and one zero. The poles can be found by setting the denominator of H2(s) equal to zero and solving for s. The zero can be found by setting the numerator of H2(s) equal to zero and solving for s.
d) The region of convergence (ROC) for the system is the region in the complex plane where the Laplace transform converges. In this case, since the system is causal, the ROC will be to the right of the rightmost pole.
e) To determine the stability of the system, we need to check if all the poles of the system function H2(s) have negative real parts. If all the poles have negative real parts, the system is stable.
f) The natural frequency (ωn) of the system can be calculated from the denominator of the system function H2(s) as ωn = √(2504). The zeta parameter (ζ) can be calculated as the coefficient of the s term in the denominator divided by 2 times the square root of the coefficient of the s^2 term.
g) The system will be oscillatory if the zeta parameter (ζ) is less than 1. If ζ = 1, the system is critically damped. If ζ is greater than 1, the system is over-damped.
h) To determine if the system is over-damped, under-damped, or critically damped, we need to compare the value of the zeta parameter (ζ) to 1.
i) The maximum gain can be determined by evaluating the magnitude response of the system at the resonant frequency. The half-power gain can be determined by finding the frequencies at which the magnitude response is half of the maximum gain. The half-power frequencies are the frequencies at which the system attenuates the input signal by 3 dB.
j) To roughly sketch the magnitude response, we can plot the magnitude of the system function H2(s) as a function of frequency. The important values to be shown would include the resonant frequency, the half-power frequencies, and any other significant peaks or dips in the magnitude response.
k) To estimate the frequency response at w = 0, w = 52 rad/s, and w = 1000 rad/s for the input x(t) = 1 + 4sin(52t) + 2sin(1000t), we can substitute the respective values of s into the system function H2(s) and calculate the magnitude and phase shift.
l) To represent the output y(t) as the sum of real sine signals, we can use Euler's formula to convert the complex exponential form of the frequency response to real sine signals. The output y(t) will be a linear combination of sine functions with different amplitudes, frequencies, and phase shifts.
Learn more about Laplace transform here:
https://brainly.com/question/31689149
#SPJ11
Write Python code for the following in pycharm: Car Class:
Write a class named Car that has the following data attributes:
_ _year_model (for the car’s year model)
_ _make (for the make of the car)
_ _speed (for the car’s current speed)
The Car class should have an _ _init_ _ method that accepts the car’s year model and
make as arguments. These values should be assigned to the object’s _ _year_model and _ _make data attributes. It should also assign 0 to the _ _speed data attribute.
The class should also have the following methods:
Accelerate:
The accelerate method should add 5 to the speed data attribute each time it is called.
Brake:
The brake method should subtract 5 from the speed data attribute each time it is called.
get_speed:
The get_speed method should return the current speed.
Next, design a program that creates a Car object then calls the accelerate method five times. After each call to the accelerate method, get the current speed of the car and display it. Then call the brake method five times. After each call to the brake method, get the current speed of the car and display it.
Write a definition for a class Device. The Device class has a data attribute for a type and a color. The class also has the following methods:
An _ _init_ _ method for the class. The method should accept arguments for each of the data attributes.
An _ _str_ _ method that returns a string showing the state of the object.
Accessor and mutator methods for each data attribute.
Sure! Here's the Python code for the Car class with the mentioned data attributes and methods:
```python
class Car:
def __init__(self, year_model, make):
self.__year_model = year_model
self.__make = make
self.__speed = 0
def accelerate(self):
self.__speed += 5
def brake(self):
self.__speed -= 5
def get_speed(self):
return self.__speed
```
In the code above, the Car class is defined with the `__init__` method that initializes the `__year_model`, `__make`, and `__speed` attributes. The `accelerate` method increases the `__speed` attribute by 5 each time it is called, and the `brake` method decreases the `__speed` attribute by 5. The `get_speed` method returns the current speed of the car. You can create an instance of the Car class and test its methods like this:
```python
# Creating a Car object
my_car = Car(2023, "Example Make")
# Checking initial speed
print(my_car.get_speed()) # Output: 0
# Accelerating the car
my_car.accelerate()
print(my_car.get_speed()) # Output: 5
# Accelerating again
my_car.accelerate()
print(my_car.get_speed()) # Output: 10
# Applying brakes
my_car.brake()
print(my_car.get_speed()) # Output: 5
`` This code demonstrates how to create a Car object, check its initial speed, accelerate, and apply brakes using the defined methods of the Car class.
Learn more about Python here:
https://brainly.com/question/30391554
#SPJ11
Moving to another question will save this response. Question 12 Find the Laplace transform of the following signals: 1) x(t) = u(t)-u(t-1) 2)x(t) = (1+e-3t cos(30t))u(t) = √²e-31 ²² 3) x (t) = For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac).
Laplace transform of the following signals can be determined by using standard Laplace transform tables and rules for differentiation and integration.
Laplace transform of x(t) = u(t)-u(t-1) x(t) is a step signal from t=0 to t=1, after t=1, x(t) becomes 0. Its Laplace transform can be computed as follows: L{u(t)} = 1/s L{u(t-1)} = e^{-s}/s L{x(t)} = L{u(t)} - L{u(t-1)} = 1/s - e^{-s}/s Hence, Laplace transform of x(t) = u(t)-u(t-1) is 1/s - e^{-s}/s.Laplace transform of x(t) = (1+e^{-3t}cos(30t))u(t) Laplace transform of cos(30t)u(t) can be found by using s = σ + jω L{cos(30t)u(t)} = ∫_{0}^{\infty}e^{-st} cos(30t) dt = Re{∫_{0}^{\infty}e^{-(σ+jω)t} cos(30t) dt}= Re{∫_{0}^{\infty}e^{-σt} (cos(30t)cos(ωt) + sin(30t)sin(ωt)) dt} = Re{∫_{0}^{\infty}e^{-σt} cos(30t)cos(ωt) dt} = σ/(σ^2 + ω^2 - 900) + ω/(σ^2 + ω^2 - 900) Using this result, we can find the Laplace transform of x(t): L{x(t)} = L{(1+e^{-3t}cos(30t))u(t)}
The Laplace transform is a mathematical operation that transforms a time-domain function into a frequency-domain representation. It is a powerful tool for solving differential equations, especially those with initial conditions. Laplace transform of a function f(t) is defined as: F(s) = ∫_{0}^{\infty}e^{-st} f(t) dt where s is a complex frequency parameter. Laplace transform of some of the basic functions are given below: L{u(t)} = 1/s (unit step function)L{e^{at}u(t)} = 1/(s-a) (exponential function) L{sin(at)u(t)} = a/(s^2 + a^2) L{cos(at)u(t)} = s/(s^2 + a^2) L{δ(t)} = 1 (Dirac delta function L{t^n} = n!/s^(n+1) (power function) L{f'(t)} = sF(s) - f(0) (derivative property) Using these standard Laplace transform properties and tables, we can find the Laplace transform of any function.
To know more about laplace visit:
https://brainly.com/question/32332387
#SPJ11
Questions 1. Calculate the minimum line width and DOF for an i-line from an Hg lamp in an optical system with NA= 0.48, k, = 0.6 and k₂= 1. Is this wavelength suitable for current CMOS trends? Is it suitable for MEMS technology?
The given information in the question is as follows:
NA= 0.48k,
= 0.6k₂
= 1
Now, the formula for the minimum line width is given as follows:
Minimum line width = k₁λ/NA
where, k₁ = 0.6λ = wavelength
NA = numerical aperture
So, putting the given values in the above equation, we get:
Minimum line width
= (0.6 × λ)/0.48
= (5/4) × (k₁λ/NA)
= (5/4) × (0.6λ/0.48)
Minimum line width = 0.938 μm
Now, the formula for the depth of focus (DOF) is given as follows:
DOF = k₂λ/NA²
where, k₂ = 1λ = wavelength
NA = numerical aperture
So, putting the given values in the above equation, we get:
DOF = λ/NA²
DOF = λ/(0.48)²
DOF = 3.52 μm
Thus, the minimum line width is 0.938 μm and the depth of focus is 3.52 μm.
This wavelength is not suitable for current CMOS trends as the minimum line width required for current CMOS trends is much smaller than this value.
However, it is suitable for MEMS technology where the minimum feature size is generally larger than in CMOS technology.
To know more about smaller visit:
https://brainly.com/question/30885891
#SPJ11
hello, please answer question
'a' please. thank you.
a) A low voltage signal carried by a single mode cable has been corrupted by interference from high voltage cables, which are all close together in a cable tray. You are to design a notch filter, acco
A notch filter is a kind of electronic filter that is widely utilized in communication systems, power supplies, and electronic equipment.
It helps to minimize signals within a specific frequency range while allowing signals outside that range to pass through the circuit with minimal attenuation. In the case of low voltage signals carried by a single-mode cable being corrupted by interference from high voltage cables, a notch filter can be designed to eliminate unwanted high-frequency interference To design a notch filter, you need to identify the frequency range of the interfering signals. The notch filter has a center frequency that is equal to the frequency of the unwanted interference signal. Once the frequency range has been identified, you can use the following formula to calculate the center
Center frequency (fc) = (f1 + f2) / 2
Where f1 is the lower frequency limit and f2 is the upper frequency limit.
The notch filter should be designed to have a sharp roll-off rate to ensure that only the desired signal is passed through the circuit. The Q-factor or quality factor of the filter can be used to control the sharpness of the roll-off rate.
In conclusion, the design of a notch filter to minimize high-frequency interference in low voltage signals carried by a single-mode cable is a feasible solution. It is necessary to determine the frequency range of the interfering signals, calculate the center frequency, and design the notch filter with the appropriate Q-factor to achieve the desired result.
To know more about electronic filter visit:
https://brainly.com/question/2640533
#SPJ11
Source 1(V1)=∠°
Source 2(V2)=∠°
R=30Ω
XL=30Ω
XC=25Ω
ZLOAD= 10Ω. Each member should solve for voltage drop across the load, ZLOAD by using five different techniques listed below: (a) Nodal Analysis (b) Mesh Analysis (c) Superposition Theorem (d) (e) Source Transformation Thevenin Theorem OR Norton Theorem
Nodal Analysis :Nodal Analysis is used to calculate the voltage across a certain resistor or element by using the node voltage technique.
The node voltage technique is based on Kirchhoff's Current Law (KCL), which states that the sum of all currents entering a node must equal the sum of all currents leaving a node. We use nodal analysis for determining the voltage drop across the load ZLOAD in this case. We can find out the nodal analysis of voltage drop across ZLOAD by using the following formula:V=I(ZLOAD)Where; V is the voltage drop across ZLOAD I is the current flowing through ZLOAD ZLOAD is the load which in this case is 10ΩWe can calculate I by using the following formula:I=(V1-V2)/ZTOTALWhere; V1 is the voltage of the source on the left V2 is the voltage of the source on the right Z TOTAL is the total impedance that the current passes through on its way from V1 to V2.
Nodal analysis is an application of Kirchhoff's Current Law, which states that the sum of all currents entering a node must equal the sum of all currents leaving a node .Mesh Analysis: Mesh analysis is a circuit analysis technique that is used to determine the voltage across a specific element in a circuit by utilizing mesh currents. The mesh current method is based on Kirchhoff's Voltage Law (KVL), which states that the sum of all voltages around a closed loop must equal zero.
To know more about Voltage visit:
https://brainly.com/question/33465836
#SPJ11
home - should display your full name, number, and brief welcoming to your website. Also there should be a button on this page that says "Explore" that kicks the user to the second page, the about page.
The home page of my website displays my full name, contact number, and a welcoming message. It includes an "Explore" button that directs users to the about page.
The home page of my website serves as the initial landing page for visitors. It is designed to provide essential information about myself and create a welcoming atmosphere. The key elements of the home page are as follows: Full Name: The page prominently displays my full name, allowing visitors to easily identify who the website belongs to. Contact Number: Alongside my name, I include my contact number to provide a means for visitors to reach out to me directly. Welcoming Message: A brief welcoming message is included to create a friendly and inviting environment. This message can be customized to reflect my personality and the purpose of the website. Explore Button: To encourage further exploration, the home page features an "Explore" button. When clicked, it redirects users to the about page, where they can learn more about me, my background, skills, and accomplishments. The combination of these elements on the home page aims to capture visitors' attention, introduce myself, and entice them to continue exploring the rest of the website.
learn more about website here :
https://brainly.com/question/32113821
#SPJ11
What is typical size and design operating conditions
of throttling devices
A refrigerant
22 system has a capacity of 55 TR at an evaporating temperature
of
-40°C when the condensing
pressure is 1500
Typical size and design operating conditions of throttling devices depend on various factors like fluid pressure, temperature, composition, viscosity, flow rate, and purpose.
Throttling devices are used to control the flow of a fluid in a system. The size and design of throttling devices depend on various factors like fluid pressure, temperature, composition, viscosity, flow rate, and purpose. Throttling devices are also called expansion devices, which are used in refrigeration and air conditioning systems to reduce the pressure of refrigerant coming from the high-pressure side to the low-pressure side.
Thermostatic expansion valves are the most common type of throttling devices used in refrigeration and air conditioning systems. They have a needle or pin valve that opens and closes in response to the temperature of the refrigerant in the evaporator.
To know more about Typical size visit:-
https://brainly.com/question/33283850
#SPJ11
While working at a company (Applied Sensors International, ASI) your manager assigned you the task of designing and implementing a system to automatically detect and record the following road highway conditions:
i. Motor vehicle speed
ii. Motor vehicle type (cars, SUVs, or Trucks)
iii. Number of Cars, SUVs, and Trucks per hour for each day
The following steps can be taken in designing and implementing a system to automatically detect and record the following road highway conditions: 1. Sensor selection, 2. Data acquisition, 3. Data Analysis, 4. User Interface, 5. Reporting.
The following steps can be taken in designing and implementing a system to automatically detect and record the following road highway conditions: i) Motor vehicle speed ii) Motor vehicle type (cars, SUVs, or Trucks) and iii) Number of Cars, SUVs, and Trucks per hour for each day.
1. Sensor selection: This is a critical stage of the design process. The sensors that are most suitable for the conditions to be monitored must be chosen. There are a variety of sensors available, including laser, infrared, ultrasonic, and radar sensors.
2. Data acquisition: A computer program must be designed to acquire the data generated by the sensors. The data collected by the sensors are transmitted to the computer program, which processes and stores it.
3. Data Analysis: The collected data is analyzed using data mining tools to extract relevant information, such as vehicle speed, type, and number per hour. This information can be used to identify the traffic patterns and make decisions.
4. User Interface: The user interface can be customized to meet the needs of different users. A simple user interface can be designed for the average user, while a more advanced interface can be designed for the technical user. The user interface can be made more user-friendly by adding graphs, tables, and maps to the interface.
5. Reporting: The information collected can be reported in different formats such as graphs, tables, and maps. Reports can be customized to suit the requirements of different users. The report can be generated on a daily, weekly, or monthly basis.
Learn more about data mining here:
https://brainly.com/question/28561952
#SPJ11
b) A satellite communication system is having ali of the parameters as given below. Continued ... ETM306 MOAILE \& SATFLLIE COMMUNICATIONS 08 มA' 2013 i) Uplink carrier-to-noise power spectral densi
Uplink carrier-to-noise power spectral density is defined as the ratio of the uplink carrier power to the uplink noise power spectral density.
This parameter is important because it affects the quality of the uplink signal that is received by the satellite. The higher the value of the uplink carrier-to-noise power spectral density, the better the quality of the uplink signal will be. Conversely, if this value is too low, the uplink signal will be difficult to detect and will be of poor quality.
Downlink carrier-to-noise power spectral density is defined as the ratio of the downlink carrier power to the downlink noise power spectral density. This parameter is important because it affects the quality of the downlink signal that is received by the ground station.
To know more about uplink visit:-
https://brainly.com/question/32881859
#SPJ11
The desired value for the controlled variable in a feedback control system is: Error Disturbance The setpoint or reference point Manipulated variable
The desired value for the controlled variable in a feedback control system is the setpoint or reference point.
A feedback control system is a control system in which the output of the system is continuously compared to a desired reference value known as a setpoint. The system's error signal is the difference between the output and the setpoint. The feedback controller reduces the error signal by manipulating a controlled variable, which is also known as an output variable. This manipulation of the output variable is done by the use of a manipulated variable which is the variable that the controller manipulates to adjust the output variable to the setpoint or reference point.
Desired value: Setpoint/Reference point A setpoint or reference point is the desired value for the controlled variable in a feedback control system. It represents the target value that the output variable should reach or maintain by the controller. If the output variable goes above or below the setpoint, then the controller adjusts the manipulated variable to bring it back to the setpoint. The setpoint or reference point can be preset or adjusted dynamically in some feedback control systems.
know more about feedback control system
https://brainly.com/question/22278183
#SPJ11
(3) A workpiece is loaded on a conveyor belt ad operates between two limits of travel. When limit switch LS2 is activated, the conveyor moves in forward. When limit switch LSI is activated, the convey
A workpiece is loaded on a conveyor belt and operates between two limits of travel. When limit switch LS2 is activated, the conveyor moves forward. When limit switch LSI is activated, the conveyor stops.
Assume the motor is connected to LS2, and LS1 is used as an emergency stop switch. To initiate the system, the emergency stop switch is turned to the "off" position. Then, when the operator turns the "start" switch to the "on" position, the system activates and the motor rotates forward. If the workpiece is detected by LS2, it will continue to move forward until it reaches LS1, which stops the motor. If the operator needs to stop the system manually, they can press the emergency stop button to stop the motor.If a workpiece is detected by LS2, the conveyor will continue to move forward. As soon as LS1 is reached, the motor stops. The motor will start again as soon as the start switch is pressed again.
This system can be improved by incorporating other sensors and controls such as proximity sensors and programmable logic controllers (PLCs). The PLC can control the speed and acceleration of the conveyor belt, as well as the motion of the motor. It can also monitor multiple sensors and execute commands based on the input. For example, the PLC can detect when the workpiece is on the conveyor belt and adjust the speed accordingly. Overall, a conveyor system with multiple sensors and controls can improve efficiency and safety.
To know more about workpiece visit:
https://brainly.com/question/32382242
#SPJ11
With the aid of a suitable diagram, outline the tests you would conduct to determine the equivalent circuit parameters of the single-phase transformers.
The equivalent circuit of the transformer comprises a few crucial parameters. This circuit is necessary to understand the behavior of the transformer and to predict the outcome of the transformer when it's operating under certain conditions. To determine these parameters, the transformer is subjected to various tests.
The flux in the core produces a counter emf in the primary winding which is out of phase with the primary voltage. The power factor in this test is typically in the range of 0.1 to 0.2.2. Short Circuit Test (Full Load Test)The Short Circuit Test is performed on the primary winding of the transformer while the secondary winding is short-circuited. It is also known as Full Load Test because in this test, the secondary winding is short-circuited which results in the maximum current flowing through the transformer. The purpose of this test is to determine the impedance voltage and copper losses of the transformer.
The wattmeter measures the power consumed by the transformer which consists of copper losses and impedance voltage. The power factor in this test is high because the transformer is operating at full load and the impedance voltage is high. The power factor in this test is typically in the range of 0.8 to 0.9.
To know more about operating visit:
https://brainly.com/question/30581198
#SPJ11
Read in a 3-character string from input into variable passwordStr. Declare a boolean variable containsAlpha and set containsAlpha to true if passwordStr contains an alphabetic character. Otherwise, set containsAlpha to false. Ex: If the input is 6yy, then the output is: Good password Note: Use getline(cin, passwordStr) to read the entire line from input into passwordStr. Output differs. See highlights below. Input Your output Expected output 5: Compare output ∧ Output differs. See highlights below. Input Your output Expected output 6: Compare output ∧ Output differs. See highlights below. Input Your output
Here's an example of how you can read a 3-character string from input, check if it contains an alphabetic character, and set the boolean variable `containsAlpha` accordingly:
```cpp
#include <iostream>
#include <string>
#include <cctype>
int main() {
std::string passwordStr;
std::cout << "Enter a 3-character password: ";
std::getline(std::cin, passwordStr);
bool containsAlpha = false;
for (char c : passwordStr) {
if (std::isalpha(c)) {
containsAlpha = true;
break;
}
}
if (containsAlpha) {
std::cout << "Good password" << std::endl;
} else {
std::cout << "Password does not contain alphabetic characters" << std::endl;
}
return 0;
}
```
Explanation:
- The code uses the `std::getline()` function to read the entire line of input into the `passwordStr` variable.
- It initializes the `containsAlpha` boolean variable to `false`.
- Then, it iterates over each character in `passwordStr` using a range-based for loop.
- Inside the loop, it checks if each character is alphabetic using the `std::isalpha()` function from the `<cctype>` library.
- If an alphabetic character is found, it sets `containsAlpha` to `true` and breaks out of the loop.
- Finally, it outputs the appropriate message based on the value of `containsAlpha`.
Note: This code assumes that you are using C++ and have included the necessary libraries. Make sure to adjust the code according to your specific requirements and programming environment.
Learn more about programming environment here:
https://brainly.com/question/29846770
#SPJ11
FILL THE BLANK.
all the spinal nerves have both sensory and motor fibers. therefore, they are described as ___________ nerves.
All the spinal nerves have both sensory and motor fibers. Therefore, they are described as mixed nerves. There are 31 pairs of spinal nerves in the human body. All of these spinal nerves are mixed nerves, which implies that they contain both sensory and motor fibers.
The spinal nerves arise in the spinal cord and exit the vertebral column via intervertebral foramina between adjacent vertebrae.A mixed nerve is one that includes both afferent (sensory) and efferent (motor) axons. Sensory axons transmit information from sensory receptors in the body to the central nervous system (CNS), whereas motor axons transmit commands from the CNS to effector cells (muscles or glands). The sensory fibers of a spinal nerve carry information from the periphery (sensory receptors or peripheral nerves) to the central nervous system, while the motor fibers of the spinal nerve are responsible for transmitting information from the CNS to effector organs, including muscles, glands, and other organs that receive motor innervation. Hence, all the spinal nerves have both sensory and motor fibers, which makes them mixed nerves. Spinal nerves are the nerves that originate in the spinal c
ord. There are 31 pairs of spinal nerves in the human body. These nerves arise in the spinal cord and exit the vertebral column via intervertebral foramina between adjacent vertebrae. These nerves contain both sensory and motor fibers. Therefore, they are described as mixed nerves.A mixed nerve contains both afferent (sensory) and efferent (motor) axons. Sensory axons transmit information from sensory receptors in the body to the central nervous system (CNS), whereas motor axons transmit commands from the CNS to effector cells (muscles or glands).The sensory fibers of a spinal nerve carry information from the periphery (sensory receptors or peripheral nerves) to the central nervous system, while the motor fibers of the spinal nerve are responsible for transmitting information from the CNS to effector organs, including muscles, glands, and other organs that receive motor innervation.
To know more about sensory visit:
https://brainly.com/question/32332387
#SPJ11
A small factory has the following loads supplied from the 230 V,
50 Hz singlephase supply: • 8 kVA at 0.8 power factor lagging; • 6
kW at unity power factor; • 9 kVA at 0.7 power factor lagging.
Three loads have been supplied from the 230 V, 50 Hz single-phase supply to a small factory, and they are as follows:
For the three loads, the current is determined using the power factor. The current is calculated as follows for the 8 kVA load at 0.8 power factor lagging: Reactive power = P*tan (θ) = 8 * tan (cos-1 0.8) = 5.77 kVAr The apparent power is given by the formula, S = P/power factor = 8/0.8 = 10 kVA Active power, P = 8 kVA * 0.8 = 6.4 kW The RMS voltage is V = 230 Vrms, whereas the frequency is 50 Hz.
Using the formula I = S/V, the current drawn by the load is: 10 kVA/230 V = 43.5 AmpsThe current drawn by the load is thus 43.5 amps (approx). For the 6 kW load at unity power factor, the power factor is one, and the current drawn is given by:I = P/V = 6,000/230 = 26.1 Amps The current drawn by the load is thus 26.1 amps (approx).
To know more about factory visit:-
https://brainly.com/question/33315111
#SPJ11
1. Identify the data type of the array elements
and predict the output, respectively:
#define Elem(A) (sizeof(A)/sizeof((A)[0]))
char *bases[] = {"%d ", "%i ", "%o ", "%x"};
for (int ix = 0; ix < Elem(bases); ++ix)
printf(bases[ix], 0xD);
(Notes 6.1, 1.11)
A. char *[4] & implementation dependent
B. char & 13 13 15 d
C. char * & 13 13 015 0xd
D. char * & 13 13 15 d
E. char ** & 13 13 15 d
2. Passing an entire structure or class to a
function rather than a pointer or reference
to it:
(Note 9.9)
A. is usually more efficient.
B. is usually less efficient.
C. will cause a compiler error.
D. permits the function to modify its original
members.
E. should always be the first choice
3. If the ASCII character set is used, what is a
serious problem:
short *ptr = (short *)malloc(sizeof(short));
if (ptr)
*ptr = 'M';
(Notes 8.4, B.1)
A. (short *)malloc should be (char *)malloc.
B. *ptr is of type short.
C. sizeof(short) bytes may not be enough to
represent the value of 'M'.
D. malloc isn’t tested for success/failure
before the allocation is accessed.
E. There is no serious problem.
4. Which is true for the following code?
int *ip = (int *)malloc(87 * sizeof(int)) + 6;
free(ip);
(Notes 6.14 & 8.4)
A. ip must be type void *
B. malloc’s argument value must be even.
C. calloc is usually faster than malloc.
D. If allocation succeeds, free(ip) frees it.
E. There’s a major problem related to the
call to free
5. In C++, given the declaration
class fog xy;
which of the following does the type of the
argument passed to function f3 match the
type of the parameter specified in the
prototype to the left of it?
(Notes 5.9, 6.1, 9.11)
A. int f3(fog &); f3(xy)
B. int f3(class fog &); f3(&xy)
C. class fog *f3(int); f3(&xy)
D. int f3(class fog *); f3(xy)
E. None of the above.
6. Which expressions must be in positions 1, 2,
and 3, respectively, in the cout statement
below to output raid the big gray wolf
const char *p[] = {"who's afraid",
"of the big", "bad gray wolf"};
cout << 1 << " " << 2 << " " << 3;
(Notes 6.16, 7.4, 8.1, 8.2)
A. &p[0][8] &*(p+1)[3] &p[2][4]
B. &p[2][8] &*((*(p+2))+3) &p[2][4]
C. &*(p+0)[8] &p[1][3] &p[2][4]
D. &p[0][8] p[1]+3 &(*(p+2))[4]
E. None will do it portably.
1. The data type of the array elements in `char *bases[]` is `char *`. The output of the code will be:
D. char * & 13 13 15 d
2. B. is usually less efficient.
3. C. sizeof(short) bytes may not be enough to represent the value of 'M'.
4. E. There’s a major problem related to the call to free.
5. E. None of the above.
6. B. &p[2][8] &*((*(p+2))+3) &p[2][4]
Learn more about array elements here:
https://brainly.com/question/28632808
#SPJ11
Write short notes on the benefits provided by PaaS technology
for developing SaaS applications. (10 marks)
Explain in detail how PaaS technology changes software
development. (10 marks)
Main Answer:
PaaS technology offers **benefits** for developing **SaaS applications** by providing a platform for streamlined development and deployment.
Supporting Answer:
Platform as a Service (PaaS) technology offers several advantages when it comes to developing Software as a Service (SaaS) applications. Firstly, PaaS provides a complete development platform, including infrastructure, runtime environment, and development tools, which significantly reduces the time and effort required to set up and manage the underlying infrastructure. This allows developers to focus more on writing code and building the SaaS application itself.
Secondly, PaaS platforms offer scalability and flexibility, enabling developers to easily scale their applications based on user demand. With PaaS, developers can leverage automatic scaling features and built-in load balancing capabilities, ensuring that the SaaS application performs well under varying workloads.
Another benefit of PaaS technology is the ease of collaboration and team development. PaaS platforms often provide features for version control, collaboration tools, and integrated development environments (IDEs), allowing multiple developers to work together seamlessly on the same application.
Furthermore, PaaS simplifies the deployment process by providing built-in deployment tools and automation capabilities. Developers can easily deploy their SaaS applications to various environments, such as testing, staging, and production, with just a few clicks or commands. This eliminates the need for manual configuration and reduces the chances of deployment errors.
Lastly, PaaS technology often includes monitoring, logging, and analytics features that help developers gain insights into the performance and usage of their SaaS applications. This data can be used to optimize the application, improve user experience, and make informed business decisions.
Overall, PaaS technology revolutionizes software development by providing a robust and efficient platform for developing and deploying SaaS applications. It empowers developers to focus on application logic and functionality, while abstracting away the complexities of infrastructure management, scalability, deployment, and collaboration.
Learn more about SaaS application here:
https://brainly.com/question/14104188
#SPJ11
(a) Discuss the advantages and disadvantages of AC synchronous machine in real-life applications. You can mention the power requirements, speed or winding arrangements etc in your discussion. \( (10 \
AC synchronous machines have both advantages and disadvantages in real-life applications. These advantages and disadvantages are as Advantages of AC synchronous machines.
Low maintenance AC synchronous machines have no commutator and brushes, which eliminates the major source of maintenance. Therefore, the maintenance cost is low and the machines are quite reliable. High efficiency AC synchronous machines have higher efficiency because of no losses associated with brushes and commutators.
AC synchronous machines have higher efficiencies than induction machines or DC machines because of this factor. Constant speed AC synchronous machines run at a constant speed, which makes them suitable for applications such as clocks, timer motors, and AC servo motors.
To know more about synchronous visit:
https://brainly.com/question/27189278
#SPJ11
Construct a 10-bits Cascaded Flash ADC with Vref = 25Volts, using 3-bits Flash ADCs and 11-bits DACs.
The maximum input voltage of the ADC is 25 volts.
To construct a 10-bit cascaded flash ADC with Vref = 25Volts using 3-bit flash ADCs and 11-bit DACs, the following steps should be followed:
Step 1: Divide the 10-bit ADC into three 3-bit flash ADCs. Hence the input voltage range of each flash ADC would be Vref/8.
Step 2: The output of each flash ADC is applied to a summing amplifier with the output of the summing amplifier connected to an 11-bit DAC, which converts the analog output voltage into a digital code.
Step 3: A priority encoder is used to convert the three 11-bit outputs from the DAC into a single 10-bit digital code.
Step 4: The resolution of the ADC is given by the formula (Vref/8)/2^3 = Vref/512 volts.
The maximum input voltage of the ADC is given by Vref, hence the maximum input voltage of the ADC is 25 volts.
To know more about voltage refer to:
https://brainly.com/question/14574817
#SPJ11
Please can you give steps with explanation. Thanks
c) Given the electrical circuit diagram in Figure 1.1, derive the transfer function \( I_{R_{2}}(s) / V(s) \) (assuming zero initial conditions), where \( I_{R_{2}} \) is the current through resistor
The circuit diagram in Figure 1.1 is as shown:
[Figure 1.1]The transfer function for current through resistor \( R_2 \) in response to input voltage V(s) can be found by applying the Kirchhoff's Current Law (KCL) at node A.
Since node A has only two branches, the sum of the currents entering the node is equal to the current leaving the node. Thus, we get the following equation:
[tex]$$\frac{V(s)}{R_1} + \frac{I_{R_2}(s)}{R_2} = 0 + \frac{I_{R_2}(s)}{R_2}$$.[/tex]
This can be rearranged to solve for [tex]\( I_{R_2}(s) / V(s) \)[/tex]as follows:
[tex]$$\frac{I_{R_2}(s)}{V(s)} = \frac{-R_1}{R_2}$$.[/tex]
Thus, the transfer function for the current through resistor [tex]\( R_2 \)[/tex] in response to input voltage V(s) is [tex]$$\frac{I_{R_{2}}(s)}{V(s)} = \frac{-R_1}{R_2}$$[/tex].Therefore, we can see that the transfer function is only dependent on the values of the resistors and is independent of the input voltage.
To know more about current visit:
https://brainly.com/question/31686728
#SPJ11
1. (30 points) A sequential circuit has three flip-flops A, B, C; one input \( x_{\text {in; }} \); and one output yout. The state diagram with transitions \( x_{\text {in }} / \) Yowt is shown in Fig
A sequential circuit consists of three flip-flops named A, B, C, one input, xin and an output yout.
The state diagram with transitions xin / Yow is given in the below figure:
In the above diagram, there are eight states labeled
S0, S1, S2, S3, S4, S5, S6, and S7.
There are eight transitions from one state to another,
each labeled with an input symbol Xin and an output symbol Yout.
The circuit diagram of the sequential circuit can be designed by using these states as shown in the below figure:
To build this circuit, we need to first derive the excitation equations for the flip-flops.
The excitation equations for flip-flops are given below:
DA = xinBC + xinB'CD = xinB'CA' = A'CD + A'B'
By using the excitation equations, the circuit diagram can be designed as shown in the above figure.
In this circuit, there are three flip-flops, A, B, and C.
The input to the circuit is xin and the output is yout.
The feedback connections from the output of one flip-flop to the input of another flip-flop are made as per the state diagram.
To know more about sequential visit:
https://brainly.com/question/32984144
#SPJ11
1. What is the voltage drop that would be across the power leads?
from a 2600-watt load, if this device is within 140 feet of the
distribution board?
The operating voltage is 120 volts,
the conductor it is #14 THHN. specify step by step if the
cable is suitable, if not, find the right cable and explain why?
The voltage drop across the power leads at 140 feet distance would be 6.13 volts.
The voltage drop across the power leads can be calculated using the following formula:
Voltage Drop = (2 * Length of Conductor * Current * Resistance) / 1000
Where,
Length of Conductor = Distance between the device and distribution board + Length of return conductor
Current = Power / Operating Voltage
Resistance = Resistance of one conductor per 1,000 feet x Distance between device and distribution board / 1,000 feet
Given that:
Power = 2600 watts
Operating Voltage = 120 volts
Distance between device and distribution board = 140 feet
Conductor size = #14 THHN
First, we need to calculate the current:
Current = Power / Operating Voltage = 2600 / 120 = 21.67 amps
Next, we need to find the resistance of one conductor per 1,000 feet. According to the NEC, the resistance of #14 THHN wire is 3.07 ohms per 1,000 feet.
Resistance = 3.07 x 140 / 1000 = 0.4308 ohms
Now we can calculate the voltage drop using the formula mentioned above:
Voltage Drop = (2 * 140 * 21.67 * 0.4308) / 1000 = 6.13 volts
Therefore, the voltage drop across the power leads at 140 feet distance would be 6.13 volts.
#14 THHN wire is only suitable for up to 15 amps of current over long distances. In this case, the current is 21.67 amps which is beyond the rated capacity of #14 THHN wire. So, the cable is not suitable for this application. A larger gauge wire such as #12 or #10 should be used to reduce the voltage drop and prevent overheating of the wire due to high current.
Learn more about voltage here
https://brainly.com/question/28632127
#SPJ11
Suppose you have just read in a bunch of numbers into a list X. Write code that would compute the median of X. Recall: to find the median you need to sort X and then find the middle number. If there are an even number of elements in X you average the two middle numbers.
Certainly! Here's the code in R to compute the median of a list of numbers stored in a vector X:
R
Copy code
# Compute the median of a list of numbers
compute_median <- function(X) {
n <- length(X)
# Sort the list in ascending order
sorted_X <- sort(X)
if (n %% 2 == 1) {
# If the number of elements is odd, return the middle number
median <- sorted_X[(n + 1) / 2]
} else {
# If the number of elements is even, average the two middle numbers
median <- mean(sorted_X[n / 2:(n / 2 + 1)])
}
return(median)
}
# Example usage
X <- c(5, 1, 3, 2, 4)
result <- compute_median(X)
print(result)
In this code, the compute_median() function takes a vector X as input and returns the median value. It sorts the elements of X in ascending order using the sort() function.
If the number of elements in X is odd, it directly returns the middle number from the sorted list. If the number of elements is even, it computes the average of the two middle numbers using the mean() function.
You can modify the vector X with your own set of numbers or add more elements to test the code. The computed median will be printed as the output.
Please note that the code assumes X contains numerical values.
Learn more about stored here:
https://brainly.com/question/31331314
#SPJ11
Given the Plant transfer function, G(s) = 1 (s + 1)(s-3) Use the following Controller in the unity-gain feedback topology such that the stable pole is cancelled and the remaining poles are moved to the specified points in the complex s-plane. Dc(s) = K(s+z) (s + p) (10 pts) Problem 4 By hand, find H4(s) such that the poles have moved to s= -5, -0.5. Also normalize the closed loop transfer function such that the DC gain is unity. (10 pts) Problem 5 By hand, find H5(s) such that the poles have moved to s=-4 tj0 (e.g., a double pole). Also normalize the closed loop transfer function such that the DC gain is unity.
Use the following controller in the unity-gain feedback topology such that the stable pole is cancelled and the remaining poles are moved to the specified points in the complex s-plane.
Dc(s) = K(s+z) / (s + p)
Problem 4By hand, find H4(s) such that the poles have moved to
s= -5, -0.5.
Also normalize the closed-loop transfer function such that the DC gain is unity.
Given that
Dc(s) = K(s + z) / (s + p)
and the plant transfer function
G(s) = 1 / (s + 1) (s - 3),
determine the unity gain feedback transfer function:
H1(s) = Dc(s) G(s) = K(s + z) / (s + p) (s + 1) (s - 3)
For stable poles at -5 and -0.5,
H4(s) = (s + 5) (s + 0.5)H1(s) / (s + 5) (s + 0.5)H1(s) + 1
If we use the Routh-Hurwitz criterion to check the stability of the system, we get K > 1.5.
To make the DC gain equal to unity, we must select the value of K to be 1.5.
For K = 1.5, H4(s) is given as follows:
H4(s) = 1.5 (s + 5) (s + 0.5) / [s (s + 1) (s - 3) + 1.5 (s + 5) (s + 0.5)]
Problem 5By hand, find H5(s) such that the poles have moved to
s= -4 tj0 (e.g., a double pole).
Also normalize the closed-loop transfer function such that the DC gain is unity.
Given that Dc(s) = K(s + z) / (s + p) and the plant transfer function
G(s) = 1 / (s + 1) (s - 3),
determine the unity gain feedback transfer function:
H1(s) = Dc(s) G(s) = K(s + z) / (s + p) (s + 1) (s - 3)
For stable poles at -4 ± j0 (double pole),
H5(s) = (s + 4)²H1(s) / (s + 4)²
H1(s) + 1
If we use the Routh-Hurwitz criterion to check the stability of the system,
To know more about controller visit:
https://brainly.com/question/30776626
#SPJ11
