The final speed of the car after the first 4.00 s of acceleration is 13.9 m/s. Therefore, option (b) is correct.
The given problem involves determining the final speed after the first 4 seconds of acceleration. Thus, it is safe to assume that the car accelerated uniformly from rest.
The initial velocity of the car, u = 0 km/hr = 0 m/s
Final velocity of the car, v = 100 km/hr = 27.8 m/s
Time, t = 8.00 s
Acceleration, a = ?
We know that the distance traveled by the car (S) during uniform acceleration can be calculated using the following equation:
S = ut + 1/2 at² ……………….(1)
where u = initial velocity, a = acceleration, t = time, and S = distance traveled.
Substituting the values in the above equation, we get:
100,000 = 0 + 1/2 a (8.00)²a
= 3.47 m/s²
Now, to determine the final speed of the car after 4 seconds of acceleration, we use the following equation:
v = u + at ……………….(2)
where v = final velocity, u = initial velocity, a = acceleration, and t = time.
Substituting the values in equation (2), we get:
v = 0 + 3.47 m/s² (4.00 s)v
= 13.9 m/s
learn more about acceleration from :
https://brainly.com/question/460763
#SPJ11
2 points Despite possible risks, Chandler throws his child, Erica, straight up into the air and catches her, while his wife, Monica, was not around. Erica has the greatest energy at her highest peak. Your answer Another of the 79 moons of Jupiter is named Europa. Europa accelerates* 2 points faster than Jupiter. Your answer True or False 2 points Sisyphus pushes a rock up a hill at a constant speed. As the block rock up the hill, its potential energy increases and its kinetic energy remains the same. Your answer 2 points Sisyphus' rock rolls down a hill at a constant speed. Its kinetic energy increases and its potential energy remains the same. Your answer
Sisyphus' rock rolls down a hill at a constant speed, and its kinetic energy increases, while its potential energy remains the same. As the rock moves down the hill, it gains kinetic energy due to its motion, and its potential energy remains constant because it is not at an elevation.
Despite possible risks, Chandler throwing his child, Erica, straight up into the air and catching her is a dangerous move. When Chandler throws his child, Erica, straight up into the air and catches her, while his wife, Monica, was not around, Erica has the greatest energy at her highest peak. It is a very risky move that can harm the child, and it is not recommended. Another of the 79 moons of Jupiter is named Europa, and it accelerates faster than Jupiter. It is a true statement that Europa accelerates faster than Jupiter. Sisyphus pushes a rock up a hill at a constant speed. As the block rock up the hill, its potential energy increases, and its kinetic energy remains the same. The potential energy of a body increases as it moves up, and its kinetic energy remains the same, according to the law of conservation of energy. Sisyphus' rock rolls down a hill at a constant speed, and its kinetic energy increases, while its potential energy remains the same. As the rock moves down the hill, it gains kinetic energy due to its motion, and its potential energy remains constant because it is not at an elevation.
To know more about elevation visit:
https://brainly.com/question/29477960
#SPJ11
What is an equalizer? Often time, providing more Eb/No will not mitigate the degradation due to inter symbol. interference explain why?
An equalizer is an electronic device that modifies the frequency response of a signal to reduce the distortion and improve the quality of the signal transmitted. An equalizer, abbreviated as EQ, is used in audio and video signal processing systems, as well as in wireless communication systems.
It adjusts the levels of different frequencies in the audio signal, allowing sound engineers to fine-tune the audio quality to their liking.The Eb/No ratio is a common measure of the signal-to-noise ratio in digital communication systems. It is the ratio of the received energy per bit to the noise power spectral density, measured in decibels.
In some cases, increasing the Eb/No ratio can help mitigate the degradation caused by inter-symbol interference (ISI).ISI occurs when a signal is transmitted through a channel that distorts the waveform, causing symbols to overlap. This can result in errors in the received signal. Increasing the Eb/No ratio can help mitigate this problem by increasing the energy per bit.
To know more about equalizer visit:
https://brainly.com/question/14642392
#SPJ11
What is the expression for the frequency response magnitude and
phase spectrum for this circuit?
The circuit is a low-pass filter consisting of a resistor and a capacitor in series. Its frequency response magnitude and phase spectrum can be found using the following expressions:
Frequency Response Magnitude: |H(jω)| = 1 / √(1 + (ωRC)²)
Phase Spectrum: ∠H(jω) = -arctan(ωRC)
where ω is the frequency in radians per second, R is the resistance in ohms, and C is the capacitance in farads.
For a given frequency, the magnitude of the frequency response tells us the amount by which the input signal is attenuated or amplified by the filter. The phase spectrum tells us how much the filter delays or advances the phase of the input signal.
To know more about resistor visit:
https://brainly.com/question/30672175
#SPJ11
A 3.0 cm × 4.0 cm rectangle lies in the xy-plane with unit vector n^ pointing in the +z-direction.
1.What is the electric flux through the rectangle if the electric field is E⃗ =(2000i^+4000k^)N/C
2.What is the electric flux through the rectangle if the electric field is E⃗ =(2000i^+4000j^)N/C
The electric flux through the rectangle is zero when the electric field is in the +z-direction. However, when the electric field is in the +x and +y directions, the electric flux is 5.37 N·m²/C.
To calculate the electric flux through a rectangle, we can use the formula:
Φ = ∫∫ E⃗ · dA⃗
where Φ is the electric flux, E⃗ is the electric field, and dA⃗ is the vector representing an infinitesimal area element on the surface of the rectangle.
Rectangle dimensions: 3.0 cm × 4.0 cm
Electric field (E⃗) for Case 1: (2000i^ + 4000k^) N/C
Electric field (E⃗) for Case 2: (2000i^ + 4000j^) N/C
1. Electric flux through the rectangle for Case 1:
Since the rectangle lies in the xy-plane and the electric field points in the +z-direction, the electric field and the normal vector to the rectangle (n^) are perpendicular. Therefore, the dot product E⃗ · dA⃗ will be zero, and the electric flux through the rectangle is zero.
Φ1 = 0
2. Electric flux through the rectangle for Case 2:
Since the electric field (E⃗) and the normal vector to the rectangle (n^) are not perpendicular, we need to calculate the dot product E⃗ · dA⃗ over the entire surface of the rectangle.
The magnitude of the electric field is E = √(Ex² + Ey² + Ez²), where Ex, Ey, and Ez are the components of the electric field vector.
For Case 2, we have E = √(2000² + 4000²) = 4472 N/C.
The area of the rectangle is A = length × width = (3.0 cm) × (4.0 cm) = 12 cm² = 0.0012 m².
Now, we can calculate the electric flux:
Φ2 = E⃗ · dA⃗ = E ⋅ A ⋅ cosθ
where θ is the angle between the electric field vector and the normal vector to the surface.
In this case, the angle θ is 0 degrees since the electric field (2000i^ + 4000j^) N/C is parallel to the xy-plane.
Φ2 = (4472 N/C) × (0.0012 m²) × cos(0°)
Φ2 = 5.37 N·m²/C
Therefore, the electric flux through the rectangle for Case 2 is 5.37 N·m²/C.
To know more about electric flux, refer to the link below:
https://brainly.com/question/31434885#
#SPJ11
The given values are diameter of rotor = 20m, 3-blade wind
turbine what is the value of lambda and Cp? I also have various
speeds of winds. the value of lambda and Cp will be same for every
speed? win
The value of lambda and Cp for a 3-blade wind turbine with a rotor diameter of 20 meters can be determined using the Betz limit formula. According to the Betz limit, the maximum possible Cp for a wind turbine is 0.59.
The value of lambda is given by the ratio of the actual power extracted by the turbine to the maximum power that could be extracted according to the Betz limit. The value of Cp is given by the ratio of the actual power extracted by the turbine to the power available in the wind.
The Betz limit formula is expressed as:
P = 0.5 × rho ×A ×v³ × Cp
Where,
P = power output
rho = air density
A = area swept by the blades
v = wind speed
Cp = coefficient of power
Thus, the value of lambda is given by:
lambda = P / (0.5 × rho × A × v³ × 0.59)
The value of lambda will vary with wind speed because the power output of the turbine depends on wind speed. As wind speed increases, the power output of the turbine increases, which affects the value of lambda. The value of Cp will also vary with wind speed because it depends on the power available in the wind.
In conclusion, the values of lambda and Cp for a 3-blade wind turbine with a rotor diameter of 20 meters can be calculated using the Betz limit formula. The values of lambda and Cp will vary with wind speed because they depend on the power output and power available in the wind, respectively.
To know more about turbine visit:
https://brainly.com/question/31783293
#SPJ11
Radium 228145 has a half-life of 5.76 years. How long does it take for the activity of radium 228 to decrease from 7.00×10
3
Bq to 5.00×10
2
Bq ? 5. Fermium 253 has a half-life of 3.00 days. A sample currently contains 4.50 kg of fermium 253 . What mass of fermium 253 was present in this sample 23.0 days ago?
The mass of fermium 253 that was present in the sample 23.0 days ago is 32.73 kg. Half-life is the time taken for the quantity of a substance to reduce to half its initial value. It is represented by t1/2.
For example, if the initial amount of radium 228145 is 7.00×10³ Bq and its half-life is 5.76 years, the time it would take to reduce to 5.00×10² Bq can be calculated as follows:
Using the half-life equation, we can find the time it would take for the radium to decrease to 5.00×102 Bq from 7.00×10³ Bq. Here's how:
Activity (A) = 7.00×10³ Bq (initial activity)
Half-life (t1/2) = 5.76 years
Final activity (A2) = 5.00×10² Bq
We can calculate the time it takes using the half-life formula as:
A2 = A(1/2)t/t1/2
where:
A2 = 5.00×10² Bq
A = 7.00×10³ Bq
t1/2 = 5.76 years
Therefore,5.00×10² Bq = 7.00×10³ Bq
(1/2)t/5.76 years
Simplifying the above equation:
1/14 = (1/2)t/5.76 years
Therefore, t = 5.76 × 14 years
The activity of radium 228 decreases from 7.00×10³ Bq to 5.00×10² Bq after 5.76 × 14 years = 80.64 years.
Half-life (t1/2) of fermium 253 is 3.00 days. The mass of fermium 253 that was present in the sample 23.0 days ago can be calculated as follows:
We can find the mass of fermium that was present in the sample 23.0 days ago using the half-life formula. We are given that the current mass of fermium in the sample is 4.50 kg and its half-life is 3.00 days. Using the formula below, we can calculate the initial mass of fermium in the sample.
Mass (m) = m02-t/t1/2
where:
m0 = initial mass
m = current mass = 4.50 kg
t = time elapsed = 23.0 days
t1/2 = half-life = 3.00 days
Therefore,m0 = m(2-t/t1/2) = 4.50(2-23/3) = 4.50×22/3 = 32.73 kg
The mass of fermium 253 that was present in the sample 23.0 days ago is 32.73 kg.
To know more about Half-life, visit:
https://brainly.com/question/31666695
#SPJ11
The dimensions of rectangular solid are measured to be 1.29 cm, 1.35 cm, and 1.5 cm. The volume should be recorded as 261225 cm3 2.62 cm3 2.6 cm3 3 cm3
The correct option is: 2.62 cm³
The correct volume (V) that should be recorded for the dimensions of the given rectangular solid(GRS) is 2.62 cm³.How to calculate the V of a rectangular solid?
The formula to calculate the V of a rectangular solid is given by; Volume = Length(L) x Width(W) x Height(H). Let us substitute the given values in the formula to find out the volume of the GRS. Volume = 1.29 cm × 1.35 cm × 1.5 cm= 2.606125 cm³. The volume should be recorded as 2.62 cm³ (rounded to two decimal places).
To know more about Rectangular solid visit:
https://brainly.com/question/28123312
#SPJ11
The Sun is ______________ through a _______________
lifespan.
about half-way, 10 billion year
most of the way, 10 billion year
most of the way, 5 billion year
about half-way, 5 billion year
The Sun is about halfway through a 10 billion-year lifespan.
Stars, including the Sun, go through different stages during their lifetimes. The Sun is currently in the main sequence phase, where it fuses hydrogen into helium in its core. This process has been ongoing for about 5 billion years. Based on current estimates, the total lifespan of the Sun is expected to be around 10 billion years.
Therefore, as it has already been shining for approximately 5 billion years, it is considered to be about halfway through its expected lifespan. As it continues to burn hydrogen and evolve, it will eventually transition to the next phases of its stellar evolution.
learn more about energy click here;
brainly.com/question/1932868
#SPJ11
"Q6
please when solving the exercise use equations from the equations sheet attached and please make sure to write the equation you are using ! Thank you so much! Question 6 Deep outer space, far from any solar systems or stars, is extremely cold at a temperature of about −455
∘
F. Although we think of outer space as being ""empty"", there are approximately 1,000,000atoms/m
3
in these regions of ""empty"" space. What is the pressure in the re regions? Compare this mathematically to atmospheric pressure here on Earth. Edit View Insert Format Tools Table 12pt ∨ Paragraph ∨⋮ frsub=
V
obj
V
sub
=
V
obj
V
ft
=
rho
f
rho
ot
y=
L
F
h=
rhogr
2γcosθ
A
1
v
1
=A
2
v
2
P+
2
1
rhov
2
+rhogy= consta
t
E
=(P+
2
1
rhov
2
+rhogy)Q η=
vA
FL
R=
πr
4
8nl
Q=
R
P
2
−P
1
N
n
=
η
2pvr
N
g
∗
=
η
rhovL
x
rms
=
2Dt
T
X
=T
c
+273.15 Ch. 1 rho=
V
m
P=
A
F
\begin{tabular}{l|l}
A
1
F
1
=
A
2
F
2
& PV=N \\ P=rhogh & n=
N
A
N
\end{tabular}"
The pressure(p) in deep outer space is much lower than the pressure at sea level. It is about 10^-14 Pascal(Pa) while the pressure at sea level is about 10^5 Pa.
Deep outer space, far from any solar systems or stars, is extremely cold at a temperature of about −455 ∘F. Although we think of outer space as being "empty", there are approximately 1,000,000 atoms/m3 in these regions of "empty" space. To find the pressure in the regions, we need to know the ideal gas law. We can write the ideal gas law as: PV = nRT. where P is pressure, volume(V) , n is the number of moles of gas, ideal gas constant(R) , and T is temperature. We can write the number of atoms per unit volume, n, as: n/V = N/V * (1 mole / 6.022 * 10^23 atoms) ,number of atoms and Avogadro's number(N) is 6.022 * 10^23.
Rearranging the equation we have: n = (N/V) * (1 mole / 6.022 * 10^23 atoms) * V, where (N/V) is the number of atoms per unit volume in the gas and V is the volume of the gas. We can substitute this expression for n into the ideal gas law: PV = [(N/V) * (1 mole / 6.022 * 10^23 atoms) * V] * R * T. We can solve for P:P = (N/V) * (1 mole / 6.022 * 10^23 atoms) * R * T. This equation is valid for an ideal gas. So, we assume that the atoms are moving around randomly, colliding with each other, and obeying the ideal gas law. To compare this mathematically to atmospheric pressure(AtmP) here on Earth, we need to know the pressure at sea level, which is approximately 101,325 Pascals(Pa). We can convert this to the units we used in the equation by using the conversion:1 Pascal = 1 N/m2So, the pressure at sea level is approximately: 101,325 Pa = 101,325 N/m2. Now, we can substitute the values for the temperature, number density of atoms, and the ideal gas constant into the equation: P = (1.0 * 10^6 / 6.022 * 10^23) * 8.31 J/(mol*K) * (-455 * (5/9) + 273) K = 3.0 * 10^-14 Pa.
to know more about Ideal gas constant visit:
https://brainly.com/question/20348074
#SPJ11
why did astronomers know where to look to discover neptune
Astronomers knew where to look to discover Neptune because its existence was mathematically predicted based on the observed irregularities in the orbit of Uranus.
In the 19th century, astronomers observed that the planet Uranus did not follow its predicted orbit exactly, and its motion exhibited irregularities. These deviations suggested the presence of an additional gravitational influence from an unknown celestial body.
Based on these observations, French mathematician Urbain Le Verrier and English mathematician John Couch Adams independently performed complex calculations to predict the existence and position of an undiscovered planet that could explain Uranus' irregularities. Using mathematical models and gravitational theory, they calculated the approximate location in the sky where this planet should be found.
Upon receiving these predictions, astronomers Johann Galle and Heinrich d'Arrest observed the predicted region and discovered Neptune on September 23, 1846, using a telescope. The accuracy of the predictions made by Le Verrier and Adams confirmed the power of mathematical modeling and led to the successful discovery of Neptune.
learn more about Astronomers here:
https://brainly.com/question/14853303
#SPJ11
In a load of 5 cubic meters of topsoil, approximately how many
cubic meters of the volume would be solid material?
In a load of 5 cubic meters of topsoil, the approximate volume of solid material would depend on the type of topsoil and its composition. However, in general, topsoil is composed of organic matter, minerals, water, and air.
The amount of each component varies depending on factors such as the location, climate, and type of vegetation present. In most cases, the organic matter and minerals account for the majority of the volume, with water and air occupying the remaining space.
The solid material in topsoil is made up of minerals, which include sand, silt, and clay particles. These particles are responsible for providing the soil with its texture, structure, and fertility. The size of the particles determines the texture of the soil, with sand being the largest and clay being the smallest.
Therefore, the amount of solid material in a load of 5 cubic meters of topsoil would depend on the type of topsoil and its composition. However, based on the average composition of topsoil, it can be estimated that approximately 3-4 cubic meters of the volume would be solid material. This means that the remaining 1-2 cubic meters would be occupied by water and air.
To know more about climate visit:
https://brainly.com/question/31966219
#SPJ11
The process where a photon comes into an atom and increases the energy of an electron is known as...
absorption
emission
fluorescence
reflection
The process where a photon comes into an atom and bounces off an electron is known as...
absorption
emission
fluorescence
reflection
The process where a photon is given off by an electron dropping to a lower energy state is known as...
absorption
emission
fluorescence
reflection
The process where a photon comes into an atom and increases the energy of an electron is known as absorption.
Absorption is the process in which light photons are absorbed by atoms or molecules when they pass through a medium. The photons' energy is transferred to the absorbing material in this process, typically elevating one or more of the material's electrons to higher energy states. When an electron moves from a lower energy level to a higher one, it absorbs energy.
Electrons release energy when they move from a higher energy level to a lower one in emission. Reflection is the phenomenon in which a light wave incident on a boundary is sent back into the same medium from which it came. Emission is the opposite of absorption, and it is the process where the energy of an electron increases, and a photon is emitted as it moves to a lower energy level.
Learn more about photon here:
https://brainly.com/question/33017722
#SPJ11
(a) An electron and a 0.0240 kg bullet each have a velocity of magnitude 490 m/s, accurate to within 0.01005. Within what lower limit could we determine the position of each object along the direction of the velocity? (Give the lower limit for the electron in mm and that for the bulletin m.)
for the electron 1.18 mm
for the bullet 4.4820-30 m
(b) What If? Within what lower limit could we determine the position of each object along the direction of the velocity if the electron and the bulet were both relativistic, traveling at 0.450c measured with the same accuracy? (Give the lower limit for the electron in nm and that for the bulletin m.)
for the electron 118 mm
Again, you will need to use the uncertainty principle, but not now the velocity is high compared to the speed of light. So, you will need to use the relativistic definition of momentum. To find the uncertainty in velocity, treat the momentum and velocity uncertainties as differentials. This will require finding the derivative of relativistic momentum with respect to velocity. Also, be sure to express your answer in nanometers.
for the bullet 1.83e-33 m
Again, you will need to use the uncertainty principle, but note now the velocity is high compared to the speed of light. 50, you will need to use the relativistic definition of momentum. To find the uncertainty in velocity, treat the momentum and velocity uncertainties as differentials. This will require finding the derivative of relativistic momentum with respect to velocity?
The lower limit for determining the position of the electron is 1.18 mm, and that for the bullet is 4.4820-3 m. The uncertainty principle is used to determine the minimum uncertainty in position.
To find the minimum uncertainty, we have to use the Heisenberg Uncertainty Principle. For a particle, the minimum uncertainty in position is given by:
[tex]Δx * Δp > = h/2π[/tex]
where Δx is the minimum uncertainty in position, Δp is the minimum uncertainty in momentum, and h is Planck's constant.
The given values are as follows:
mass of electron, m = 9.10938356 × 10⁻³¹ kg
mass of bullet, m = 0.0240 kg
speed of electron, v1 = 490 m/s
speed of bullet, v2 = 490 m/s
accuracy = 0.01005
For the electron
Δp = m * Δv
m * (v1 * 0.01005) = 9.10938356 × 10⁻³¹ kg * 490 m/s * 0.01005
= 4.490315 × 10⁻³¹ kg.m/s
Δx = (h/2π) / Δp = (6.62607015 × 10⁻³¹ J.s/2π) / (4.490315 × 10⁻³¹ kg.m/s)
= 0.0000011795189 m
= 1.18 mm
For the bullet
Δp = m * Δv = 0.0240 kg * 490 m/s * 0.01005 = 0.0117808 kg.m/s
Δx = (h/2π) / Δp
= (6.62607015 × 10⁻³¹ J.s/2π) / (0.0117808 kg.m/s)
= 0.004481944 m = 4.4820⁻³ m (correct to 4 significant figures)
Therefore, the minimum uncertainty in the position of the electron is 1.18 mm and that of the bullet is 4.4820⁻³ m.
Thus, the lower limit for determining the position of the electron is 1.18 mm, and that for the bullet is 4.4820⁻³ m. The uncertainty principle is used to determine the minimum uncertainty in position.
To know more about uncertainty principle, visit:
https://brainly.com/question/30402752
#SPJ11
There is a uniform magnetic field of magnitude 2.2 T in the +z-direction. Find the magnitude F1 of the force on a particle of charge −1.4nC if its velocity is 1.4 km/s in the y−z plane in a direction that makes an angle of 38∘ with the z-axis. F1= Find the magnitude F2 of the force on the same particle if its velocity is 1.4 km/s in the x−y plane in a direction that makes an angle of 38∘ with the x-axis.
The magnitude F1 of the force on the particle is approximately 8.596 x [tex]10^{-9}[/tex] N and the magnitude F2 of the force on the particle is approximately 8.596 x [tex]10^{-9}[/tex] N.
To find the magnitude F1 of the force on the particle, we can use the formula for the magnetic force on a charged particle moving in a magnetic field. The formula is given by
F = qvBsinθ,
where
F is the force,
q is the charge of the particle,
v is its velocity,
B is the magnetic field,
θ is the angle between the velocity and the magnetic field.
Charge of the particle, q = -1.4nC = -1.4 x [tex]10^{-9}[/tex] C
Velocity, v = 1.4 km/s = 1.4 x [tex]10^{3}[/tex] m/s
Magnetic field, B = 2.2 T
Angle, θ = 38°
Plugging in the values into the formula, we get:
F1 = (-1.4 x [tex]10^{-9}[/tex] C) x (1.4 x [tex]10^{3}[/tex] m/s) x (2.2 T) x sin(38°)
Calculating the value, we get:
F1 ≈ -8.596 x [tex]10^{-9}[/tex] N
Therefore, the magnitude F1 of the force on the particle is approximately 8.596 x [tex]10^{-9}[/tex] N.
To find the magnitude F2 of the force on the same particle, we can use the same formula but with a different angle θ.
Velocity, v = 1.4 km/s = 1.4 x [tex]10^{3}[/tex] m/s
Angle, θ = 38°
Plugging in the values into the formula, we get:
F2 = (-1.4 x [tex]10^{-9}[/tex] C) x (1.4 x [tex]10^{3}[/tex] m/s) x (2.2 T) x sin(38°)
Calculating the value, we get:
F2 ≈ -8.596 x [tex]10^{-9}[/tex] N
Learn more about the magnetic field
https://brainly.com/question/26257705
#SPJ11
What kind of heating systems involve circulation of the air in a room?
Heating systems that involve the circulation of air in a room are known as forced air heating systems.
Heating systems that involve the circulation of air in a room are known as forced air heating systems. These systems use a furnace or heat pump to generate heat, which is then distributed throughout the room or building using a network of ducts. The heated air is forced through the ducts by a blower or fan, allowing it to circulate and warm the space.
Forced air heating systems are commonly used in residential and commercial buildings due to their efficiency and ability to quickly heat large areas. They can be powered by various energy sources, including natural gas, electricity, or oil.
Learn more:About heating systems here:
https://brainly.com/question/26301591
#SPJ11
The kind of heating systems that involve circulation of the air in a room is the forced-air heating system. The forced-air heating system is a type of heating system that is found in many residential homes, commercial buildings and industrial applications.
It circulates the air in a room by using a fan or blower to distribute warm air throughout the building.An important component of a forced-air heating system is a furnace that generates heat and is located in a central location. The furnace heats up air and the warm air is then distributed through a network of ducts that run throughout the building.
The ducts are usually located in the walls, ceiling or floors of the building and they carry the warm air to the different rooms that require heating.In conclusion, a forced-air heating system involves circulation of the air in a room through the use of a furnace, fan or blower, and a network of ducts that distribute warm air throughout the building.
To know more about heating system visit:-
https://brainly.com/question/30651040
#SPJ11
1. Calculate voltage ab such that voltage across 2 Ohm resistor is 20 V. I, 6.0 a + V b 2012 I 10 I 20 2. A 42 resistor in series with a 7.96 mH inductor is connected across a 110 V 60 Hz source. Determine (a) the impedance, (b) input current, (c) the voltage across the resistor and the inductor, (d) draw phasor diagram showing the current and voltage.
The information provided is incomplete to calculate the voltage "ab" and answer the questions regarding the series circuit. Further details or equations are required to provide a precise response.
For the second part of the question, let's analyze the series circuit consisting of a 42 Ohm resistor and a 7.96 mH inductor connected to a 110V, 60 Hz source:
(a) The impedance of the circuit (Z) can be calculated using the formula Z = √(R^2 + (ωL)^2), where R is the resistance and ω is the angular frequency (2πf) of the source. Plugging in the values, Z = √((42^2) + ((2π * 60 * 7.96 * 10^(-3))^2)).
(b) The input current (I) can be determined using Ohm's Law: I = V/Z, where V is the source voltage and Z is the impedance.
(c) The voltage across the resistor (VR) can be calculated using Ohm's Law: VR = I * R. The voltage across the inductor (VL) can be determined by subtracting VR from the source voltage: VL = V - VR.
(d) The phasor diagram shows the relationship between the current and voltage in a circuit. It represents the magnitude and phase of the current and voltage. Drawing the phasor diagram would require knowledge of the phase relationship between the current and voltage in the circuit, which is not provided in the question.
Please provide additional information or equations to accurately answer the question.
To know more about resistor ,
https://brainly.com/question/30672175
#SPJ11
Two moles of an ideal monatomic gas go through the cycle abcabc. For the complete cycle, 900 JJ of heat flows out of the gas. Process abab is at constant pressure, and process bcbc is at constant volume. States aa and bb have temperatures TaTaT_a = 205 KK and TbTbT_b = 310 KK
for the complete cycle abcabc, the heat flowing out of the gas is approximately 1925.6 J.
To analyze the given cycle, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system:
ΔU = Q - W
Since the process abab is at constant pressure, the work done in this process can be calculated using the equation:
W = PΔV
Since the process bcbc is at constant volume, the work done in this process is zero:
W = 0
Therefore, for the complete cycle abcabc, the total work done is:
W = W[tex](abab)[/tex] + W[tex](bcbc)[/tex]
W = P[tex](abab)[/tex]ΔV[tex](abab)[/tex] + 0
W = P([tex]abab[/tex])ΔV[tex](abab)[/tex]
Given that the heat flowing out of the gas for the complete cycle is 900 J, we can rewrite the first law of thermodynamics equation as:
ΔU = Q - W
ΔU = Q - P(abab)ΔV(abab)
Since the gas is monatomic, the change in internal energy (ΔU) can be expressed as:
ΔU = (3/2) nR ΔT
Where n is the number of moles and R is the ideal gas constant.
Substituting the known values and rearranging the equation, we have:
Q - P(abab)ΔV(abab) = (3/2) nR ΔT
We are given the temperatures Ta = 205 K and Tb = 310 K. Therefore, the temperature difference can be expressed as:
ΔT = Tb - Ta
Substituting this into the equation and rearranging, we have:
Q - P[tex](abab)[/tex]ΔV[tex](abab)[/tex]= (3/2) [tex]nR[/tex] (Tb - Ta)
We are also given that the number of moles is 2. Therefore, the equation becomes:
Q - P[tex](abab)[/tex]ΔV[tex](abab)[/tex]= 3R (Tb - Ta)
Now, we need to express the change in volume (ΔV[tex](abab)[/tex]) in terms of pressure (P[tex](abab))[/tex]. This can be done using the ideal gas law equation:
PV =[tex]nRT[/tex]
Rearranging the equation, we have:
ΔV[tex](abab)[/tex] = Vb - Va = (nR / P[tex](abab)[/tex]) (Tb - Ta)
Substituting this back into the equation, we have:
Q -[tex]P(abab)[/tex] [(nR / P[tex](abab))[/tex](Tb - Ta)] = 3R (Tb - Ta)
Simplifying the equation:
Q - nR (Tb - Ta) = 3R (Tb - Ta)
We can cancel out the common terms:
Q - nR (Tb - Ta) = 3R (Tb - Ta)
Q - 2R (Tb - Ta) = 3R (Tb - Ta)
Now we can solve for the heat flowing out of the gas, Q:
Q = 2R (Tb - Ta)
Substituting the given values for the ideal gas constant R, temperature Ta, and temperature Tb, we have:
Q = 2 * (8.314 J/(mol*K)) * (310 K - 205 K)
Q ≈ 1925.6 J
to know more about work visit:
brainly.com/question/31050706
#SPJ11
Gas in a container increases its pressure from 1 atm
to 3 atm while keeping its volume constant. Find the work done (in
J) by the gas if the volume is 5 liters.
a.
3 J
b.
5 J
c.
0 J
d.
7 J
e.
15 J
The work done (in J) by the gas if the volume is 5 liters is 10 J.
Hence, option A is correct.
Given that the gas in a container increases its pressure from 1 atm to 3 atm while keeping its volume constant.
We need to find the work done (in J) by the gas if the volume is 5 liters.Work done by the gas is given by the equation
W = PΔV, where
ΔV = change in volume.
P = change in pressure and
W = work done
Substitute the given values in the formula, ΔV = 0 since the volume remains constant,
P = 3 atm – 1 atm =
2 atm and
V = 5 L
So,
W = 2 atm × 5 L
= 10 L-atm
= 10 J
Therefore, the work done (in J) by the gas if the volume is 5 liters is 10 J.
Hence, option A is correct.
To know more about work done visit:
https://brainly.com/question/32263955
#SPJ11
B
=5.46×10
−10
sin(1.43×10
7
y−4.30×10
15
t)
i
^
T where y is in metres and t is in seconds. Part 1) What is the wavelength of this wave? λ= m Part 2) Which of these terms best describes this wave? Part 3) Write an equation to describe the electric field of this wave.
E
= sin( ) V/m The final box is for the unit vector showing direction.
Given the electric field of a wave isE = B sin(ky - ωt) i^ T where B = 5.46 × 10^-10,T, y is in metres and t is in seconds.
Part 1) λ= m
The wavelength of this wave can be calculated using the formulaλ = 2π/k = 2π/1.43 × 10^7 m^-1 = 4.4 × 10^-8 m.
Part 2) The electric field equation of the given wave, E = B sin(ky - ωt) i^ T describes a plane-polarized wave.
Part 3) Write an equation to describe the electric field of this wave. E = B sin(ky - ωt) i^ T = 5.46 × 10^-10 sin(1.43 × 10^7 y - 4.30 × 10^15 t) i^ T.
The unit of electric field is V/m and the electric field equation for the given wave is E = 5.46 × 10^-10 sin(1.43 × 10^7 y - 4.30 × 10^15 t) i^ T.
To know more about wavelength refer to:
https://brainly.com/question/10750459
#SPJ11
4. Define Ampere circuital law and describe it for filament, surface, and volume current.
Ampere's circuital law is a physical law used to determine the magnetic field that arises around a current-carrying conductor.
It states that for any closed loop path, the sum of the length elements multiplied by the magnetic field in the direction of the length element is equal to the vacuum permeability times the electric current that passes through the loop.
Mathematically, it can be expressed as ∮B.dl = μI, where B is the magnetic field, dl is an element of the length, μ is the vacuum permeability, and I is the current.
The law is applicable for all types of currents, whether they are filament, surface, or volume currents.
For filament current, the Ampere circuital law states that the magnetic field around a straight, infinitely long conductor is proportional to the current passing through it and inversely proportional to the distance from the conductor.
For surface current, the magnetic field around a conductor is dependent upon the current density distribution across the surface of the conductor.
For volume current, the Ampere circuital law states that the magnetic field around the current-carrying conductor is proportional to the current density and varies with the shape and size of the conductor.
Learn more about Ampere's circuital law from the given link
https://brainly.in/question/35957
#SPJ11
Kilauea in Hawaii is the world’s most continuously active volcano. Very active volcanoes characteristically eject red-hot rocks and lava rather than smoke and ash. Suppose a large rock is ejected from the volcano with a speed of 25.0 m/s and at an angle 35.0º above the horizontal. The rock strikes the side of the volcano at an altitude 20.0 m lower than its starting point. (a) Calculate the time it takes the rock to follow this path. (b) What are the magnitude and direction of the rock’s velocity at impact?
Given information:
Speed of the rock = 25.0 m/s
Angle made by rock with horizontal = 35.0º
The initial altitude of the rock = h1 = 0 m
The final altitude of the rock = h2
= -20 m
(a) Time it takes the rock to follow this path: Let's calculate the time taken by the rock to reach at altitude of -20 m from its initial point. We can use the kinematic equation of motion:
Δy = Viyt + 1/2gt²Where,
Δy = h2 - h1
= -20 m Viy
= Vi sin θ
= 25 sin 35°
= 14.3 m/s
g = acceleration due to gravity
= -9.8 m/s² (negative because it acts in the opposite direction to the direction of the motion of the rock)
t = time taken by the rock Substituting the given values,
Δy = Viyt + 1/2gt²-20
= 14.3t + 1/2 (-9.8) t²-20
= 14.3t - 4.9t²
We can solve this quadratic equation to find t. We can use the quadratic formula for this purpose:
t = [-b ± √(b² - 4ac)]/2a
Where, a = -4.9, b = 14.3, and
c = -20
t = [-14.3 ± √(14.3² - 4(-4.9)(-20))] / 2(-4.9)
t = [-14.3 ± √(14.3² + 392)] / 9.8
t = [-14.3 ± 19.8] / 9.8
t = [-14.3 + 19.8] / 9.8 or [-14.3 - 19.8] / 9.8
t = 0.561 s or 3.13 s
The positive value of t is the required time taken by the rock to reach at altitude of -20 m from its initial point, i.e., 0.561 s (rounded to three significant figures).
(b) Magnitude and direction of the rock’s velocity at impact:Let's calculate the magnitude and direction of the rock’s velocity at impact. We can use the kinematic equation of motion:
Vf = Vi + gt
Where, Vi = initial velocity of the rock = 25.0 m/sθ = angle made by the rock with horizontal = 35.0ºV
f = final velocity of the rock at impact
t = time taken by the rock = 0.561 s
Substituting the given values,
Vf = Vi + gtVf
= 25.0 + (-9.8) x 0.561V
f = 19.4 m/s
The magnitude of the rock’s velocity at impact is 19.4 m/s (rounded to three significant figures). We can use the following trigonometric formula to find the direction of the rock’s velocity at impact:
tan θ = Vy / Vx
Where, Vx = horizontal component of the velocity of the rock at impact = Vf cos θ
= 19.4 cos 35°
= 15.8 m/sVy
= vertical component of the velocity of the rock at impact
= Vf sin θ
= 19.4 sin 35°
= 11.1 m/s
Substituting the given values,tan θ = Vy / Vxtan θ = 11.1 / 15.8θ = tan⁻¹(11.1 / 15.8)θ = 36.2° The direction of the rock’s velocity at impact is 36.2° above the horizontal (rounded to one decimal place).
Answer:The time it takes the rock to follow this path is 0.561 s (rounded to three significant figures). The magnitude of the rock’s velocity at impact is 19.4 m/s (rounded to three significant figures). The direction of the rock’s velocity at impact is 36.2° above the horizontal (rounded to one decimal place).
To know more about velocity, visit:
https://brainly.com/question/30559316
#SPJ11
Consider two resistors, R1 and R2, being placed in a circuit. Consider the equivalent resistance Req of the resistors and compare it to each resistance if (a) the resistors are placed in a series configuration, or if (b) the resistors are placed in a parallel configuration. Specifically, say if Req is greater/smaller than each resistance or if it depends on other circumstances.
The question is asking about the equivalent resistance (Req) of two resistors (R1 and R2) in different circuit configurations: series and parallel.
We need to determine if Req is greater or smaller than each resistance, or if it depends on other circumstances.
(a) In a series configuration, the resistors are connected one after another. The equivalent resistance (Req) is given by the sum of the individual resistances (R1 + R2). Therefore, Req is always greater than each resistance because it is the sum of both resistors.
(b) In a parallel configuration, the resistors are connected side by side. The equivalent resistance (Req) is given by the reciprocal of the sum of the reciprocals of the individual resistances. Therefore, 1/Req = 1/R1 + 1/R2. In this case, Req is always smaller than each resistance because the reciprocal of Req is the sum of the reciprocals of R1 and R2.
In conclusion, the equivalent resistance (Req) depends on the circuit configuration. In a series configuration, Req is greater than each resistance, while in a parallel configuration, Req is smaller than each resistance.
To learn more about series configuration and parallel configuration:
https://brainly.com/question/29217225
#SPJ11
A charge of 2.0nC is uniformly distributed along a circular arc (radius 1.0 m ) that is subtended by a 90-degree angle. Calculate the magnitude of the electric field at the center of the circle along which the arc lies.
the magnitude of the electric field at the center of the circle along which the arc lies is 18 N/C.
To calculate the magnitude of the electric field at the center of the circle due to the uniformly distributed charge along a circular arc, we can use the concept of integration.
The electric field at a point due to a small charge element is given by Coulomb's law:
dE = (k * dq) / r^2
Where:
dE is the electric field due to the small charge element,
k is the electrostatic constant (k = 9 x 10^9 N m^2/C^2),
dq is the charge of the small element,
r is the distance from the small element to the point where we want to find the electric field.
To find the electric field at the center of the circle, we need to integrate the electric field contributions from all the small charge elements along the arc.
Let's assume the total charge along the arc is Q = 2.0 nC = 2.0 x 10^-9 C.
Since the charge is uniformly distributed along the arc, we can consider each small charge element as dq = (dθ / 90°) * Q, where dθ is the differential angle of each small element.
The electric field due to each small element at the center of the circle is given by:
dE = (k * (dθ / 90°) * Q) / r^2
Now, we can integrate the electric field contributions over the entire 90° arc to find the total electric field at the center.
E = ∫ dE
E = ∫ [(k*(dθ / 90°) * Q) / r^2]
E = (k*Q) / (90° * r^2) * ∫ dθ
E = (k*Q) / (90° * r^2) * θ
E = (k*Q*θ) / (90° * r^2)
Since the angle θ subtended by the arc is 90°, we can substitute θ = 90° in the equation:
E = (k *Q *90°) / (90° *r^2)
E = (k *Q) / r^2
Now we can substitute the values:
k = 9 x 10^9 N m^2/C^2 (electrostatic constant)
Q = 2.0 x 10^-9 C (total charge along the arc)
r = 1.0 m (radius of the circle)
E = (9 x 10^9 N m^2/C^2 * 2.0 x 10^-9 C) / (1.0 m^2)
Simplifying the equation:
E = 18 N/C
Therefore, the magnitude of the electric field at the center of the circle along which the arc lies is 18 N/C.
Learn more about Coulomb's law:
https://brainly.com/question/506926
#SPJ11
PRACTICE IT Use the worked example above to help you solve this problem. A diverging lens of focal length f = -9.9 cm forms images of an object situated at various distances. (a) If the object is placed p₁ = 29.7 cm from the lens, locate the image, state whether it's real or virtual, and find its magnification. 9 = -7.42 cm M = 0.25 (b) Repeat the problem when the object is at p₂ = 9.9 cm. 9 = -4.95 cm 0.17 M X Your response differs from the correct answer by more than 10%. Double check your calculations. (c) Repeat the problem again when the object is 4.95 cm from the lens. a -3.3 cm -0.11 X M Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. EXERCISE HINTS: GETTING STARTED I I'M STUCK! Use the values from PRACTICE IT to help you work this exercise. Repeat the calculation, finding the position of the image and the magnification if the object is 20.6 cm from the lens. q = -6.69 cm 0.23 X M = What factors affect the magnification of an image?
a) the magnification is 0.17.
b) the magnification is 0.5.
c) the magnification is 0.67.
(a) The given information is:focal length,
f = -9.9 cm
p₁ = 29.7 cm
9 = -7.42 cm
M = 0.25
The object is placed at a distance of 29.7 cm from the lens. The image is formed at a distance of 9 cm from the lens.
Using the lens formula,
1/f = 1/v - 1/u
where,
u = -29.7 cm,
f = -9.9 cm
On substituting the values, we get
1/v = 1/-9.9 - 1/-29.7
v = -6.633 cm
The image is formed at a distance of 6.633 cm from the lens.
Since the image is formed on the same side as the object, the image is virtual. Magnification is given by,
|m| = v/u
|0.25| = -6.633/-29.7
On simplifying,
|m| = 0.17
Therefore, the magnification is 0.17.
(b) When the object is placed at a distance of 9.9 cm from the lens, then,
u = -9.9 cm,
f = -9.9 cm
The lens formula is given as,
1/f = 1/v - 1/u
On substituting the values, we get,
1/v = 1/-9.9 - 1/-9.9
v = -4.95 cm
The image is formed at a distance of 4.95 cm from the lens. Since the image is formed on the same side as the object, the image is virtual.
Magnification is given by,
|m| = v/u
|0.25| = -4.95/-9.9
On simplifying,
|m| = 0.5
Therefore, the magnification is 0.5.
(c) When the object is placed at a distance of 4.95 cm from the lens, then,
u = -4.95 cm,
f = -9.9 cm
The lens formula is given as,
1/f = 1/v - 1/u
On substituting the values, we get,
1/v = 1/-9.9 - 1/-4.95
v = -3.3 cm
The image is formed at a distance of 3.3 cm from the lens. Since the image is formed on the same side as the object, the image is virtual.
Magnification is given by,
|m| = v/u
|0.25| = -3.3/-4.95
On simplifying,
|m| = 0.67
Therefore, the magnification is 0.67.
Factors affecting the magnification of an image are:
i) the focal length of the lens
ii) the distance between the lens and the object
iii) the distance between the lens and the image.
To know more about magnification visit:
https://brainly.com/question/21370207
#SPJ11
What problems might we face if measuring system were not established?
If a standardized measuring system were not established, several problems could arise such as Lack of uniformity, Inefficiency and errors, Safety concerns and Economic impact.
Lack of uniformity: Without a standardized system, different regions or communities might develop their own measurement units, leading to confusion and inconsistency in communication and trade. It would be challenging to compare and reconcile measurements across different contexts.
Inefficiency and errors: A lack of standardized measurements could result in inefficiency in various sectors, such as construction, engineering, and manufacturing. Precision and accuracy would be compromised, leading to errors in calculations, designs, and product quality.
Safety concerns: Standardized measurements play a crucial role in ensuring safety, particularly in areas like medicine, transportation, and infrastructure. Without a common system, it would be difficult to establish safety standards, monitor compliance, and ensure uniformity in critical aspects like dosage, weight limits, and structural integrity.
Economic impact: Inconsistent measurement systems would hinder international trade and commerce. Harmonized measurements facilitate smooth transactions, accurate pricing, and quality control, leading to a stable and efficient economy. Without a standardized system, business operations and global collaborations would be significantly hindered.
In conclusion, a lack of a standardized measuring system would result in confusion, inefficiency, safety concerns, and economic setbacks, emphasizing the importance of establishing and adhering to universally accepted measurements.
Know more about communication here:
https://brainly.com/question/28153246
#SPJ8
A single-phase, 50Hz transformer has 25 primary turns and 300 secondary turns. The cross-sectional area of the core is 300cm2. When the primary winding is connected to a 250V supply, determine (a) the maximum value of the flux density in the core, and (b) the voltage induced in the secondary winding.
(a) Maximum value of flux density in the core:The maximum value of the flux density is given by,Where V = 250 V, N1 = 25, A = 300 cm², f = 50 HzAnd,
Thus, the maximum value of the flux density in the core is 0.287 Wb/m² or 287 mT.(b) The voltage induced in the secondary winding:The induced voltage in the secondary winding is given by,Where N1 = 25, N2 = 300, Φm = 0.287 Wb and f = 50 Hz.
Now, substituting the given values in the above equation,Therefore, the voltage induced in the secondary winding is 21 V.
To know more about flux visit:-
https://brainly.com/question/15655691
#SPJ11
1. What is the peak wavelength of a blackbody with a temperature of 12000 K? (10 points)
2. The index of refraction of bone is n = 1.55. What is the speed of light in bone?
3. A light beam is shone into a mystery material. The light beam has an incident angle of 34 degrees and a refracted angle of 21 degrees. If n1 = 1.00, what is n2?
Substituting T = 12000 K, we getλ_max = 2.898 × 10^−3 m K/12000 K= 2.41 × 10^−7 m2. The speed of light in bone can be found using the formula:
v = c/n where c is the speed of light in a vacuum and n is the index of refraction of the medium. The speed of light in a vacuum is approximately 3.0 × 10^8 m/s.
1. The peak wavelength of a blackbody with a temperature of 12000 K can be found using Wien's displacement law. According to Wien's displacement law, the peak wavelength (λ_max) of a blackbody radiation is inversely proportional to the temperature of the object. The formula for Wien's displacement law is given as:λ_maxT = constant
The constant of proportionality is given by Wien's constant (b = 2.898 × 10^−3 m K).Therefore,λ_max = b/TSubstituting T = 12000 K, we getλ_max = 2.898 × 10^−3 m K/12000 K= 2.41 × 10^−7 m2. The speed of light in bone can be found using the formula:v = c/nwhere c is the speed of light in a vacuum and n is the index of refraction of the medium. The speed of light in a vacuum is approximately 3.0 × 10^8 m/s.
Substituting n = 1.55, we getv = (3.0 × 10^8 m/s)/1.55= 1.94 × 10^8 m/s3. Snell's law of refraction relates the angles of incidence and refraction to the indices of refraction of the two materials. The formula for Snell's law of refraction is given as:n1 sinθ1 = n2 sinθ2where n1 and θ1 are the refractive index and angle of incidence of the first medium, respectively,
and n2 and θ2 are the refractive index and angle of refraction of the second medium, respectively. Rearranging the formula, we get:n2 = (n1 sinθ1)/sinθ2Substituting n1 = 1.00, θ1 = 34°, and θ2 = 21°, we get:n2 = (1.00 × sin 34°)/sin 21°= 1.61Hence, the index of refraction of the mystery material is 1.61.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
Ant and his tab partner creats a single sit by carefully algning two rasr Mades to a spation of me whan a hum-1000, to the first minimum in the diffraction patton and the width of the cena HINT (a) the anges to the first me the diffaction pattom on de Need Help? 7. (-/1 Points) DETAILS SERCP11247.P.037. A with me dated with ight of waveleng and cred (1 ma APPL the , xaftaction pathen in observed in a 235 beynd the scheme MY NOTES ASE YOUR TEACHER PRACTICE ANOTHER of the fand danach of the or
The width of the central maximum can be obtained as: w = λD/aWhere, D is the distance between the slit and the screen and a is the separation between the blades. Putting the given values in the above equation, we get;w = λD/a = (600 nm)(235 cm)/(0.1 mm) = 14.1 mm Hence, the width of the central maximum of the diffraction pattern is 14.1 mm.
Here's the solution to the problem you provided:Given data:A slit is created by carefully aligning two razor blades to a separation of 0.1 mm. The light of wavelength 600 nm is used. A diffraction pattern is observed at a distance of 235 cm beyond the slit.(a) The angles to the first minimum in the diffraction pattern on the screen.(b) The width of the central maximum of the diffraction pattern.(a) The angles to the first minimum in the diffraction pattern on the screen.The position of the first minimum in the diffraction pattern is given by, sinθ
= λ/dWhere, λ is the wavelength of light, d is the distance between the razor blades and θ is the angle subtended by the first minimum at the slit. Putting the given values in the above equation, we get;sinθ
= λ/d
= 600 nm/0.1 mm
= 0.006θ
= sin-1(0.006)
= 0.34°Hence, the angle to the first minimum in the diffraction pattern is 0.34°. (b) The width of the central maximum of the diffraction pattern.The central maximum is the bright central portion of the diffraction pattern that is formed on the screen. The width of the central maximum can be obtained as: w
= λD/aWhere, D is the distance between the slit and the screen and a is the separation between the blades. Putting the given values in the above equation, we get;w
= λD/a
= (600 nm)(235 cm)/(0.1 mm)
= 14.1 mm Hence, the width of the central maximum of the diffraction pattern is 14.1 mm.
To know more about maximum visit:
https://brainly.com/question/30693656
#SPJ11
If a force of 100N stretches a spring by 0.1cm find;
a. The elastic constant
b. The work done in stretching the spring 0.3cm if the elastic limit is not exceeded
(a) The elastic constant of the spring is 100,000 N/m.
(b) Te work done in stretching the spring by 0.3cm is 0.45 J.
What is the elastic constant of the spring?The elastic constant of the spring is calculated by applying the following formula as follows;
F = kx
where;
F is the force appliedk is the elastic constant x is the extension of the spring100N = k (0.001m)
k = 100N / 0.001m
k = 100,000 N/m
(b) The work done in stretching the spring by 0.3cm is calculated as;
Work = ¹/₂kx²
Work = ¹/₂ x 100,000 N/m x (0.003m)²
Work = 0.45 J
Learn more about elastic constant here: https://brainly.com/question/1968517
#SPJ1
Light from the sun reaches Earth in 8.3 min. The velocity of light is 3.00 ✕ 108 m/s. How far is Earth from the sun? m
Earth is approximately 1.50 × 10¹¹ meters (m) away from the sun.
The light from the sun reaches Earth in 8.3 minutes and the velocity of light is 3.00 × 10⁸ m/s, we can calculate the distance between Earth and the sun.
The formula to calculate distance is:
Distance = Velocity × Time
Substituting the values:
Distance = (3.00 × 10⁸ m/s) × (8.3 minutes × 60 seconds/minute)
First, convert minutes to seconds:
Distance = (3.00 × 10⁸ m/s) × (498 seconds)
Distance = 1.50 × 10¹¹ meters (m)
This distance is commonly referred to as one astronomical unit (AU), which is the average distance from Earth to the sun.
learn more about Distance here:
https://brainly.com/question/4928657
#SPJ11
