Answer:
(i) The inductance of the inductor is = 43.43 mH (ii) the impedance of the circuit is = 16∠58.61° Ω (iii) the phase difference for current and the voltage applied is Q = 58.61°
Explanation:
Solution
Given that:
I= 5 A
V = 125V
Resistance R= Not known yet
Thus
To find the resistance we have the following formula which is shown below:
R = V/I
=125/15
R =8.333Ω
Now,
Voltage = 240
Frequency = 50Hz
Current (I) remain at = 15A
Z= not known (impedance)
so,
To find the impedance we have the formula which is shown below:
Z = V/I =240/15
Z= 16Ω⇒ Z = R + jXL
Z = 8.333 + jXL = 16
Thus
√8.333² + XL² = 16²
8.333² + XL² = 16²
XL² = 186.561
XL = 13.658Ω
Now
We find the inductance of the Inductor and the impedance of the circuit.
(i) In solving for the inductance of the inductor, a formula is applied here, which is shown below:
L = XL/w
=13.658/ 2π * 50
=13.658/314.15 = 0.043 = 43.43 mH
Note: w= 2πf
(ii) For the impedance of the circuit we have the following:
z = 8.333 + j 13.658
z = 16∠58.61° Ω
(iii) The next step is to find the phase difference between the applied voltage and current.
Q = this is the voltage across the inductor in a series of resonant circuit.
Q can also be called the applied voltage
Thus,
Q is described as an Impedance angle
Therefore, Q = 58.81°
Increase the sampling time by a factor of 10 (to 0.1 seconds), keeping the frequency of the square wave the same, and observe the delay. Discuss relationship between sampling time and delay from one board to another.
Answer:
Time delay increases
Explanation:
Time delay is the delay between occurance of signal. If sampling time that is time between two samples is increased, the delay in the occurance of regenerated samples is also increased.
A fully recrystallized sheet of metal with a thickness of 11 mm is to be cold worked by 40% in rolling. Estimate the necessary roll force if the sheet was 0.5 m wide and there was no lateral spreading during rolling. The strength coefficient is 200 MPa, the work hardening exponent of 0.1 and the roll contact length is 40 mm. Assume no friction.
Answer:
Roll force, F = 5.6 MN
Explanation:
Sheet width, b = 0.5 m
Roll contact length, [tex]l_{p} = 40 mm[/tex]
Strength coefficient, [tex]\sigma_{0} = 200 MPa[/tex]
Thickness, h = 11 mm
Since the sheet of metal is cold worked by 40%, the reduction in thickness will be:
Δh = 40% * 11 = 0.4 * 11 = 4.4 mm
Strain, e = (Δh)/h
e = 4.4/11 = 0.4
The roll force is calculated by the formula:
[tex]F = \sigma_{f} l_{p} b[/tex]
[tex]\sigma_{f} = \sigma_{0} (e+1)\\\sigma_{f} = 200 (0.4+1)\\\sigma_{f} = 200 *1.4\\\sigma_{f} = 280 MPa[/tex]
Substituting the value of [tex]\sigma_{f}[/tex], [tex]l_{p}[/tex], and b into the formula for the roll force:
[tex]F = \sigma_{f} l_{p} b\\F = 280 * 0.04 * 0.5\\F = 5.6 MN[/tex]
The ABC Corporation manufactures and sells two products: T1 and T2. 20XX budget for the company is given below:
Projected Sales Units Price T1 60,000 $165 T2 40,000 $250
Inventories in Units January 1, 20XX December 31, 20XX T1 20,000 25,000 T2 8,000 9,000
The following direct materials are used in the two products: Amount used per unit Direct Material Unit T1 T2 A pound 4 5 B pound 2 3 C each 0 1
Anticipated Inventories Direct Material Purchase Price January 1, 2012 December 31, 2012 A $12 32,000 lb. 36,000 lb. B $5 29,000 lb. 32,000 lb. C $3 6,000 units 7,000 units
Projected direct manufacturing labor requirements and rates for 20XX are as follows: Hours per Unit Rate per Hour T1 2 $12 T2 3 $16
4
Manufacturing overhead is allocated at the rate of $20 per direct manufacturing labor-hour. Marketing and distribution costs are projected to be $100,000 and $ 300,000, respectively.
a. What is the total expected revenue (in dollars) for 20XX? b. What is the expected production level (in units) both for T1 and T2? c. What is the total direct material purchases (in dollars) for each type of direct material? d. What is the total direct manufacturing labor cost (in dollars)? e. What is the total overhead cost (in dollars)? f. What is the total cost of goods sold (in dollars)? g. What is the total expected operating income (in dollars) for 20XX?
Answer:
The ABC Corporation
a) Total Expected Revenue (in dollars) for 20XX:
Revenue from T1 = 60,000 x $165 = $26,400,000
Revenue from T2 = 40,000 x $250 = $10,000,000
Total Revenue from T1 and T2 = $36,400,000
b) Production Level (in units) for T1 and T2
T1 T2
Total Units sold 160,000 40,000
Add Closing Inventory 25,000 9,000
Units Available for sale 185,000 49,000
less opening inventory 20,000 8,000
Production Level 165,000 units 41,000 units
c) Total Direct Material Purchases (in dollars):
Cost of direct materials used T1 T2
A: (165,000 x 4 x $12) $7,920,000 $2,460,000 (41,000 x 5 x $12)
B: (165,000 x 2 x $5) 1,650,000 615,000 (41,000 x 3 x $5)
C: 0 123,000 (41,000 x 1 x$3)
Total cost $9,570,000 $3,198,000 Total = $12,768,000
Cost of direct per unit = $58 ($9,570,000/165,000) for T1 and $78 ($3,198,000/41,000) for T2
Cost of direct materials used for production $12,768,000
Cost of closing direct materials:
A (36,000 x $12) $432,000
B (32,000 x $5) 160,000
C (7,000 x $3) 21,000 $613,000
Cost of direct materials available for prodn $13,381,000
Less cost of beginning direct materials:
A (32,000 x $12) $384,000
B (29,000 x $5) 145,000
C (6,000 x $3) 18,000 $547,000
Cost of direct materials purchases $12,834,000
d) The Total Direct Manufacturing Labor Cost (in dollars):
T1 T2
Direct labor per unit 2 hours 3 hours
Direct labor rate per hour $12 $16
Direct labor cost per unit $24 $48
Production level 165,000 units 41,000 units
Labor Cost ($) $3,960,000 $1,968,000
Total labor cost $5,928,000 ($3,960,000 + $1,968,000)
e) Total Overhead cost (in dollars):
Overhead rate = $20 per labor hour
Overhead cost per unit: T1 = $40 ($20 x 2) and T2 = $60 ($20 x 3)
T1 overhead = $20 x 2 x 165,000) = $6,600,000
T2 overhead = $20 x 3 x 41,000) = $2,460,000
Total Overhead cost = $9,060,000
Cost of goods produced:
Cost of opening inventory of materials = $547,000
Purchases of directials materials 12,834,000
less closing inventory of materials = $613,000
Cost of materials used for production 12,768,000
add Labor cost 5,928,000
add Overhead cost 9,060,000
Total production cost $27,756,000
f) Total cost of goods sold (in dollars):
Cost of opening inventory = $3,928,000
Total Production cost = $27,756,000
Cost of goods available for sale $31,684,000
Less cost of closing inventory $4,724,000
Total cost of goods sold $26,960,000
g) Total expected operating income (in dollars)
Sales Revenue: T1 and T2 $36,400,000
Cost of goods sold 26,960,000
Gross profit $9,440,000
less marketing & distribution 400,000
Total Expected Operating Income = $9,040,000
Explanation:
a) Cost of beginning inventory of finished goods:
T1, (Direct materials + Labor + Overhead) X inventory units =
T1 = 20,000 x ($58 + 24 + 40) = $2,440,000
T2 = 8,000 ($78 + 48 + 60) = $1,488,000
Total cost of beginning inventory = $3,928,000
b) Cost of closing Inventory of finished goods:
T1 = 25,000 x ($58 + 24 + 40) = $3,050,000
T2 = 9,000 ($78 + 48 + 60) = $1,674,000
Total cost of closing inventory = $4,724,000
Liquid benzene and liquid n-hexane are blended to form a stream flowing at a rate of 1700 lbm/h. An on-line densitometer (an instrument used to determine density) indicates that the stream has a density of 0.810 g/mL. Using specific tractors from Table B.1, estimate the mass and volumetric feed rates of the two hydrocarbons to the mixing vessel (in U.S. customary units). State at least two assumptions required to obtain the estimate from the recommended date.
A piston-cylinder assembly contains 5kg of water that undergoes a series of processes to form a thermodynamic cycle. Process 1à 2: Constant pressure cooling from p1=20bar and T1=360°C to saturated vapor Process 2à 3: Constant volume cooling to p3=5 bar Process 3à 4: Constant pressure heating Process 4à 1: Polytropic process following Pv =constant back to the initial state Kinetic and potential energy effects are negligible. Calculate the net work for the cycle in kJ.
Answer:
[tex]W_{net} = - 1223 kJ[/tex]
Explanation:
State 1:
[tex]P_1 = 20 bar\\T_1 = 360^{0}C\\ h_1 = 3159.3 kJ/kg\\S_1 = 6.9917 kJ/kg[/tex]
State 2:
[tex]P_2 = 20 bar\\x_2 = 1 \\ h_2 = 2799.5 kJ/kg\\u_2 = 2600.3 kJ/kg\\v_2 = 0.09963m^3/kg[/tex]
State 3:
[tex]P_2 = 5 bar\\v_2 = v_3 \\v_3 = v_f + x_3 (v_g - v_f)\\0.09963 = (1.0926 * 10^{-3}) +x_3 (0.3749 - (1.0926 * 10^{-3}))\\x_3 = 0.263[/tex]
[tex]u_{3} = u_f + x_3 ( u_g - u_f)\\u_{3} = 639.68 + 0.263 (2561.2 - 639.68)\\u_{3} = 1146.2 kJ/kg[/tex]
State 4:
[tex]P_{4} = 5 bar\\T_4 = 360^0 C\\h_4 = 3188.4 kJ/kg\\S_4 = 7.660 kJ/kg-K\\Q_{12} = h_2 - h_1 = 2799.5-3159.3 = -359 kJ/kg\\Q_{23} = u_3 - h_2 =1146.2-2006.3 = -1454.1 kJ/kg\\Q_{34} = h_4 - h_3 = 3188.4-1196.04 = 1992.36 kJ/kg\\Q_{41} = T(S_1 - S_4) = (360 + 273) (6.9917 - 7.660) = -423.04 kJ/kg[/tex]
Calculate the network done for the cycle
[tex]W_{net} = m( Q_{12} + Q_{23} + Q_{34} + Q_{41})\\W_{net} = 5( -359.8 - 1454.1 + 1992.36 - 423.04)\\W_{net} = -1223 kJ[/tex]
Under the normal sign convention, the distributed load on a beam is equal to the:_______A. The rate of change of the bending moment with respect to the shear force. B. The second derivative of the bending moment with respect to the length of the beam. C. The rate of change of the bending moment with respect to the length of the beam. D. Negative of the rate of change of the shear force with respect to the length of the beam.
Answer:
Under the normal sign convention, the distributed load on a beam is equal to the: O The second derivative of the bending moment with respect to the length of the beam O Negative of the rate of change of the shear force with respect to the length of the beam.
Sorry if the answer is wrong
An aluminium bar 600mm long with a diameter 40mm has a hole drilled in the centre of which 30mm in diameter and 100mm long if the modulus of elasticity is 85GN/M2 calculate the total contraction oon the bar due to comprehensive load of 160KN.
Answer:
Total contraction on the bar = 1.238 mm
Explanation:
Modulus of Elasticity, E = 85 GN/m²
Diameter of the aluminium bar, [tex]d_{Al} = 40 mm = 0.04 m[/tex]
Load, P = 160 kN
Cross sectional area of the aluminium bar without hole:
[tex]A_1 = \frac{\pi d_{Al}^2 }{4} \\A_1 = \frac{\pi 0.04^2 }{4}\\A_1 = 0.00126 m^2[/tex]
Diameter of hole, [tex]d_h = 30 mm = 0.03 m[/tex]
Cross sectional area of the aluminium bar with hole:
[tex]A_2 = \frac{\pi( d_{Al}^2 - d_{h}^2)}{4} \\A_2 = \frac{\pi (0.04^2 - 0.03^2) }{4}\\A_2 = 0.00055 m^2[/tex]
Length of the aluminium bar, [tex]L_{Al} = 600 mm = 0.6 m[/tex]
Length of the hole, [tex]L_h = 100mm = 0.1 m[/tex]
Contraction in aluminium bar without hole [tex]= \frac{P * L_{Al}}{A_1 E}[/tex]
Contraction in aluminium bar without hole [tex]= \frac{160*10^3 * 0.6}{0.00126 * 85 * 10^9 }[/tex]
Contraction in aluminium bar without hole = 96000/107100000
Contraction in aluminium bar without hole = 0.000896
Contraction in aluminium bar with hole [tex]= \frac{P * L_{h}}{A_2 E}[/tex]
Contraction in aluminium bar without hole [tex]= \frac{160*10^3 * 0.1}{0.00055 * 85 * 10^9 }[/tex]
Contraction in aluminium bar without hole = 16000/46750000
Contraction in aluminium bar without hole = 0.000342
Total contraction = 0.000896 + 0.000342
Total contraction = 0.001238 m = 1.238 mm
list everything wrong with 2020
Answer:
George Floyd (BLACK LIFES MATTER)
C O V I D - 19
Quarantine
no sports
wearing a mask
and a whole lot of other stuff
Explanation:
there is usually a positive side and a negative side to each new technological improvement?
Answer:
positive sides:
low cost improves production speedless timeeducational improvementsnegative sides:
unemployment lot of space required increased pollution creates lots of ethical issuesConsider a classroom for 56 students and one instructor, each generating heat at a rate of 100 W. Lighting is provided by 18 fluorescent lightbulbs, 40 W each, and the ballasts consume an additional 10 percent. Determine the rate of internal heat generation in this classroom when it is fully occupied. The rate of internal heat generation in this classroom when it is fully occupied is W.
Answer:
What is the probability of selecting the 4 of spade or black diamond from a deck of 52 playing cards?
a) 2/52
b) 4/52
c) 3/52
d) 1/5
Explanation:
An insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains 4 kg of an ideal gas at 750 kPa and 48°C, and the other part is evacuated. The partition is now removed, and the gas expands into the entire tank. Determine the final temperature and pressure in the tank. (Round the final answers to the nearest whole number.)
Answer:
The final temperature and pressure in the insulated rigid tank are [tex]48\,^{\circ}C[/tex] and [tex]375\,kPa[/tex].
Explanation:
An ideal gas is represented by the following model:
[tex]P\cdot V = \frac{m}{M}\cdot R_{u} \cdot T[/tex]
Where:
[tex]P[/tex] - Pressure, measured in kilopascals.
[tex]V[/tex] - Volume, measured in cubic meters.
[tex]m[/tex] - Mass of the ideal gas, measured in kilograms.
[tex]M[/tex] - Molar mass, measured in kilograms per kilomole.
[tex]T[/tex] - Temperature, measured in Kelvin.
[tex]R_{u}[/tex] - Universal constant of ideal gases, equal to [tex]8.314\,\frac{kPa\cdot m^{3}}{kmol\cdot K}[/tex]
As tank is rigid and insulated, it means that no volume deformations in tank, heat and mass interactions with surroundings occur during expansion process. Hence, final pressure is less that initial one, volume is doubled (due to equal partitioning) and temperature remains constant. Hence, the following relationship can be derived from model for ideal gases:
[tex]\frac{P_{1}\cdot V_{1}}{T_{1}} = \frac{P_{2}\cdot V_{2}}{T_{2}}[/tex]
Now, final pressure is cleared:
[tex]P_{2} = P_{1}\cdot \frac{T_{2}}{T_{1}}\cdot \frac{V_{1}}{V_{2}}[/tex]
[tex]P_{2} = (750\,kPa)\cdot 1 \cdot \frac{1}{2}[/tex]
[tex]P_{2} = 375\,kPa[/tex]
The final temperature and pressure in the insulated rigid tank are [tex]48\,^{\circ}C[/tex] and [tex]375\,kPa[/tex].
: Explain why testing can only detect the presence of errors, not their absence?
Answer:
The goal of the software is to observe the software behavior to meet its requirement expectation. In software engineering, validating software might be harder since client's expectation may be vague or unclear.
Explanation:
Find the minimum diameter of an alloy, tensile strength 75 MPa, needed to support a 30 kN load.
Answer:
The minimum diameter to withstand such tensile strength is 22.568 mm.
Explanation:
The allow is experimenting an axial load, so that stress formula for cylidrical sample is:
[tex]\sigma = \frac{P}{A_{c}}[/tex]
[tex]\sigma = \frac{4\cdot P}{\pi \cdot D^{2}}[/tex]
Where:
[tex]\sigma[/tex] - Normal stress, measured in kilopascals.
[tex]P[/tex] - Axial load, measured in kilonewtons.
[tex]A_{c}[/tex] - Cross section area, measured in square meters.
[tex]D[/tex] - Diameter, measured in meters.
Given that [tex]\sigma = 75\times 10^{3}\,kPa[/tex] and [tex]P = 30\,kN[/tex], diameter is now cleared and computed at last:
[tex]D^{2} = \frac{4\cdot P}{\pi \cdot \sigma}[/tex]
[tex]D = 2\sqrt{\frac{P}{\pi \cdot \sigma} }[/tex]
[tex]D = 2 \sqrt{\frac{30\,kN}{\pi \cdot (75\times 10^{3}\,kPa)} }[/tex]
[tex]D = 0.0225\,m[/tex]
[tex]D = 22.568\,mm[/tex]
The minimum diameter to withstand such tensile strength is 22.568 mm.
Describe what you have been taught about the relationship between basic science research, and technological innovation before this class. Have you been told that it is similar to the linear model? Is your view of this relationship different after studying this unit's lectures and readings? Explain why in 3-4 sentences
Answer:
With the Breakthrough of Technology, the rate at which things are done are becoming much more easy. but without basic science, innovation towards technology cannot occur, so the both work hand in hand in the world of technology today.
Explanation:
Technological innovation and Basic science research plays a major role in the world of science and technology today, while we all want technology innovation the more, without basic science, innovation cannot come in place,
Just as we are going further in technology, breakthroughs and growth are been made which helps on the long run in science research which in turn has made things to be done much better and easily.
The drum has a mass of 50 kg and a radius of gyration about the pin at O of 0.23 o k m = . If the 15kg block is moving downward at 3 / m s , and a force of P N =100 is applied to the brake arm, determine how far the block descends from the instant the brake is applied until it stops. Neglect the thickness of the handle. The coefficient of kinetic friction at the brake pad is 0.5 k = .
Note: The diagram referred to in this question is attached as a file below.
Answer:
The block descended a distance of 9.75m from the instant the brake is applied until it stops.
Explanation:
For clarity and easiness of expression, the calculations and the Free Body Diagram are contained in the attached file. Check the attached file below.
The block descended a distance of 9.75 m
A piston–cylinder device contains 0.85 kg of refrigerant- 134a at 2108C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 158C. Determine (a) the final pressure, (b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a.
Question:
A piston–cylinder device contains 0.85 kg of refrigerant- 134a at -10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Determine (a) the final pressure, (b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a.
Answer:
a) 90.4 kPa
b) 0.0205 m³
c) 17.4 kJ/kg
Explanation:
Given:
Mass, m = 0.85 kg
a) The final pressure here is equal to the initial pressure. Let's use the formula:
[tex] P_2 = P_1 = P_a_t_m + \frac{mg}{\pi D^2 / 4}[/tex]
[tex] = 88*10^3 + \frac{12kg * 9.81}{\pi (0.25)^2 / 4} [/tex]
= 90398 Pa
≈ 90.4 KPa
Final pressure = 90.4 kPa
b) Change in volume of the cylinder:
To find the initial and final volume, let's use the values from the A-13 table for refrigerant-134a, at initial values of 90.4 kPa and -10°C and final values of 90.4 kPa and 15°C
v1 = 0.2302m³/kg
h1 = 247.76 kJ/kg
v2 = 0.2544 m³/kg
h2 = 268.2 kJ/kg
Change in volume is calculated as:
Δv = m(v2 - v1)
Δv = 0.85(0.2544 - 0.2302)
= 0.0205 m³
Change in volume = 0.0205 m³
c) Change in enthalpy
Let's use the formula:
Δh = m(h2 - h1)
= 0.85(268.2 - 247.76)
= 17.4 kJ/kg
Change in enthalpy = 17.4 kJ/kg
A phone charger requires 0.5 A at 5V. It is connected to a transformer with 100 % of efficiency whose primary contains 2200 turns and is connected to 220-V household outlet.
(a) How many turns should there be in the secondary?
(b) What is the current in the primary?
(c) What would be the output current and output voltage values if number of secondary turns (N2) doubled of its initial value?
Answer:
Explanation:
a ) for transformer which steps down voltage , if V₁ and V₂ be voltage of primary and secondary coil and n₁ and n₂ be the no of turns of wire in them
V₁ /V₂ = n₁ / n₂
Here V₁ = 220 V , V₂ = 5V , n₁ = 2200 n₂ = ?
220 /5 = 2200 / n₂
n₂ = 2200 x 5 / 220
= 50
b )
for 100 % efficiency
input power = output power
V₁ I₁ = V₂I₂
I₁ and I₂ are current in primary and secondary coil
220 x I₁ = 5 x .5
I₁ = .01136 A .
c )
If n₂ = 100
V₁ /V₂ = n₁ / n₂
220 / V₂ = 2200 / 100
V₂ = 10 V
V₁ I₁ = V₂I₂
220 x .01136 = 10 I₂
I₂ = .25 A.
Suppose you used the pipette to make 10 additions to a flask, and suppose the pipette had a 10% random error in the amount delivered with each delivery. Use equation 1 on page 25 to calculate the percent error in the total volume delivered to the flask using the number of clicks you were permitted to make. Report that total percentage below.
Here is the equation: random error of average= error in one measurement/n^1/2
Answer:
The total percentage is 3.16237%
Explanation:
Solution
Now,
We have to know what a random error is.
A random error is an error in measured caused by factors or elements which varies from one measurement to another.
The random error is shown as follows:
The average random error is = the error found in one measurement/n^1/2
Where
n =Number ( how many times the experiment was done)
Now that we added 10 times we have that,
n → 10
Thus,
The error in one measurement = 10%
So,
The average random error = 10 %/(10)^1/2
= (10)^1/2 %
√10%
The total percentage is = 3.16237%
When an electrical signal travels through a conductive wire, it produces an electromagnetic (EM) field. Likewise, when an EM field encounters a conductive wire, it produces a proportional electrical current.
A. True
B. False
Answer:
A. True
Explanation:
When an electromagnetic field wave strikes a conductor, say a wire, it induces an alternating current that is proportional to the wave in the conductor. This is a reversal of generating electromagnetic wave from accelerating a charged particle. This phenomenon is used in radio antena for receiving radio wave signals and also use in medicine for body scanning.
A small grinding wheel is attached to the shaft of an electric motor which has a rated speed of 4200 rpm. When the power is turned on, the unit reaches its rated speed in 5 s, and when the power is turned off, the unit coasts to rest in 70 s. Assume uniformly accelerated motion. determine the number of revolutions that the motor executes
(a) in reaching its rated speed,
(b) in coating to rest.
Answer:
a) [tex]\ddot n = 50400\,\frac{rev}{min^{2}}[/tex], b) [tex]n = 2450\,rev[/tex]
Explanation:
a) The acceleration experimented by the grinding wheel is:
[tex]\ddot n = \frac{4200\,\frac{rev}{min} - 0 \,\frac{rev}{min} }{\frac{5}{60}\,min }[/tex]
[tex]\ddot n = 50400\,\frac{rev}{min^{2}}[/tex]
Now, the number of revolutions done by the grinding wheel in that period of time is:
[tex]n = \frac{(4200\,\frac{rev}{min} )^{2}-(0\,\frac{rev}{min} )^{2}}{2\cdot \left(50400\,\frac{rev}{min^{2}} \right)}[/tex]
[tex]n = 175\,rev[/tex]
b) The acceleration experimented by the grinding wheel is:
[tex]\ddot n = \frac{0 \,\frac{rev}{min} - 4200\,\frac{rev}{min} }{\frac{70}{60}\,min }[/tex]
[tex]\ddot n = -3600\,\frac{rev}{min^{2}}[/tex]
Now, the number of revolutions done by the grinding wheel in that period of time is:
[tex]n = \frac{(0\,\frac{rev}{min} )^{2} - (4200\,\frac{rev}{min} )^{2}}{2\cdot \left(-3600\,\frac{rev}{min^{2}} \right)}[/tex]
[tex]n = 2450\,rev[/tex]
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb⋅ft, a bending moment of 1500 lb⋅ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are σY= 100 ksi and τY = 50 ksi, respectively, determine the required diameter of the shaft using the maximum-shear-stress theory
Answer:
Explanation:
Given that:
Torque T = 2300 lb - ft
Bending moment M = 1500 lb - ft
axial thrust P = 2500 lb
yield points for tension σY= 100 ksi
yield points for shear τY = 50 ksi
Using maximum-shear-stress theory
[tex]\sigma_A = \dfrac{P}{A}+\dfrac{Mc}{I}[/tex]
where;
[tex]A = \pi c^2[/tex]
[tex]I = \dfrac{\pi}{4}c^4[/tex]
[tex]\sigma_A = \dfrac{P}{\pi c^2}+\dfrac{Mc}{ \dfrac{\pi}{4}c^4}[/tex]
[tex]\sigma_A = \dfrac{2500}{\pi c^2}+\dfrac{1500*12c}{ \dfrac{\pi}{4}c^4}[/tex]
[tex]\sigma_A = \dfrac{2500}{\pi c^2}+\dfrac{72000c}{\pi c^3}}[/tex]
[tex]\tau_A = \dfrac{T_c}{\tau}[/tex]
where;
[tex]\tau = \dfrac{\pi c^4}{2}[/tex]
[tex]\tau_A = \dfrac{T_c}{\dfrac{\pi c^4}{2}}[/tex]
[tex]\tau_A = \dfrac{2300*12 c}{\dfrac{\pi c^4}{2}}[/tex]
[tex]\tau_A = \dfrac{55200 }{\pi c^3}}[/tex]
[tex]\sigma_{1,2} = \dfrac{\sigma_x+\sigma_y}{2} \pm \sqrt{\dfrac{(\sigma_x - \sigma_y)^2}{2}+ \tau_y^2}[/tex]
[tex]\sigma_{1,2} = \dfrac{2500+72000}{2 \pi c ^3} \pm \sqrt{\dfrac{(2500 +72000)^2}{2 \pi c^3}+ \dfrac{55200}{\pi c^3}} \ \ \ \ \ ------(1)[/tex]
Let say :
[tex]|\sigma_1 - \sigma_2| = \sigma_y[/tex]
Then :
[tex]2\sqrt{( \dfrac{2500c + 72000}{2 \pi c^3})^2+ ( \dfrac{55200}{\pi c^3})^2 } = 100(10^3)[/tex]
[tex](2500 c + 72000)^2 +(110400)^2 = 10000*10^6 \pi^2 c^6[/tex]
[tex]6.25c^2 + 360c+ 17372.16-10,000\ \pi^2 c^6 =0[/tex]
According to trial and error;
c = 0.75057 in
Replacing c into equation (1)
[tex]\sigma_{1,2} = \dfrac{2500+72000}{2 \pi (0.75057) ^3} \pm \sqrt{\dfrac{(2500 +72000)^2}{2 \pi (0.75057)^3}+ \dfrac{55200}{\pi (0.75057)^3}}[/tex]
[tex]\sigma_{1,2} = \dfrac{2500+72000}{2 \pi (0.75057) ^3} + \sqrt{\dfrac{(2500 +72000)^2}{2 \pi (0.75057)^3}+ \dfrac{55200}{\pi (0.75057)^3}} \ \ \ OR \\ \\ \\ \sigma_{1,2} = \dfrac{2500+72000}{2 \pi (0.75057) ^3} - \sqrt{\dfrac{(2500 +72000)^2}{2 \pi (0.75057)^3}+ \dfrac{55200}{\pi (0.75057)^3}}[/tex]
[tex]\sigma _1 = 22193 \ Psi[/tex]
[tex]\sigma_2 = -77807 \ Psi[/tex]
The required diameter d = 2c
d = 1.50 in or 0.125 ft
You are standing at the edge of the roof of the engineering building, which is H meters high. You see Professor Murthy, who is h meters tall, jogging towards the building at a speed of v meters/second. You are holding an egg and want to release it so that it hits Prof Murthy squarely on top of his head. What formulas describes the distance from the building that Prof Murthy must be when you release the egg?
Answer:
s = v√[2(H - h)/g]
This formula describes the distance from the building that Prof Murthy must be when you release the egg
Explanation:
First, we need to find the time required by the egg to reach the head of Professor. For that purpose, we use 1st equation of motion in vertical form:
Vf = Vi + gt
where,
Vf = Velocity of egg at the time of hitting head of the Professor
Vi = initial velocity of egg = 0 m/s (Since, egg is initially at rest)
g = acceleration due to gravity
t = time taken by egg to come down
Therefore,
Vf = 0 + gt
t = Vf/g ----- equation (1)
Now, we use 3rd euation of motion for Vf:
2gs = Vf² - Vi²
where,
s = height dropped = H - h
Therefore,
2g(H - h) = Vf²
Vf = √[2g(H - h)]
Therefore, equation (1) becomes:
t = √[2g(H - h)]/g
t = √[2(H - h)/g]
Now, consider the horizontal motion of professor. So, the minimum distance of professor from building can be found out by finding the distance covered by the professor in time t. Since, the professor is running at constant speed of v m/s. Therefore:
s = vt
s = v√[2(H - h)/g]
This formula describes the distance from the building that Prof Murthy must be when you release the egg
g a heat engine is located between thermal reservoirs at 400k and 1600k. the heat engine operates with an efficiency that is 70% of the carnot effieciency. if 2kj of work are produced, how much heat is rejected to the low temperature reservior
Answer:
Heat rejected to cold body = 3.81 kJ
Explanation:
Temperature of hot thermal reservoir Th = 1600 K
Temperature of cold thermal reservoir Tc = 400 K
efficiency of the Carnot's engine = 1 - [tex]\frac{Tc}{Th}[/tex]
eff. of the Carnot's engine = 1 - [tex]\frac{400}{600}[/tex]
eff = 1 - 0.25 = 0.75
efficiency of the heat engine = 70% of 0.75 = 0.525
work done by heat engine = 2 kJ
eff. of heat engine is gotten as = W/Q
where W = work done by heat engine
Q = heat rejected by heat engine to lower temperature reservoir
from the equation, we can derive that
heat rejected Q = W/eff = 2/0.525 = 3.81 kJ
The temperature of a flowing gas is to be measured with a thermocouple junction and wire stretched between two legs of a sting, a wind tunnel test fixture. The junction is formed by butt-welding two wires of different material. For wires of diameter D = 125 m and a convection coefficient of h = 700 W/m^2 K, determine the minimum separation distance between the two legs of the sting, L=L1+L2, to ensure that the sting temperature does not influence the junction temperature and, in turn, invalidate the gas temperature measurement. Consider two different types of thermocouple junctions consisting of (i) copper and constantan wires and (ii) chromel and aluminel wires. Evaluate the thermal conductivity of copper and constantan at T300 K. Use kCh =19 W/mK and kA = l29 W/mK for the thermal conductivities of the chromel and alumel wires, respectively.
Answer:
minimum separation distance between the two legs of the sting L = L 1 + L 2 therefore L = 9.48 + 4.68 = 14.16 mL = 1.14 mExplanation:
D ( diameter ) = 125 m
convection coefficient of h = 700 W/m^2
Calculate THE CROSS SECTIONAL AREA
Ac = [tex]\frac{\pi }{4} * D^2[/tex] = [tex]\frac{\pi }{4} * ( 125 )^2[/tex] = 0.79 * 15625 = 12343.75 m^2
perimeter
p = [tex]\pi * D[/tex] = 3.14 * 125 = 392.5 m
at 300k temperature the thermal conductivity of copper and constantan from the thermodynamic property table are :
Kcu = 401 w/m.k
Kconstantan = 23 W/m.k
To calculate the length of copper wire of the thermocouple junction
L 1 = 4.6 ([tex]\frac{Kcv Ac}{h P}[/tex]) ^ 1/2 = 4.6 [tex](\frac{401 *12343.75 }{700 *392.5})^\frac{1}{2}[/tex]
L 1 = 4.6 ( 4949843.75 / 274750 )^1/2
L 1 = 9.48 m
calculate length of constantan wire
L 2 = 4.6 [tex](\frac{kcons*Ac}{hp} )^\frac{1}{2}[/tex]
= 4.6 ( (23 * 12343.75) / ( 700 * 392.5) ) ^1/2
L 2 = 4.6 ( 283906.25 / 274750 ) ^ 1/2
L 2 = 4.68 m
I) therefore the minimum separation distance between the two legs of the sting L = L 1 + L 2
L = 9.48 + 4.68 = 14.16 m
ii) Evaluating the thermal conductivity of copper and constantan
Kc ( thermal conductivity of chromel) = 19 w/m.k
Ka ( thermal conductivity of alumel ) = 29 W/m.k
distance between the legs L = L 1 + L 2
THEREFORE
L = 4.6 ( (Kcn * Ac ) / ( hp ) )^1/2 + 4.6 ( (Kac * Ac)/(hp) )^1/2
L = 4.6 [tex](\frac{Ac}{hp} )^\frac{1}{2} [ (Kcn)^\frac{1}{2} + (Kal)^\frac{1}{2} ][/tex]
L = 4.6 ( 12343.75 /( 700 * 392.5) )^1/2 * [ 19^1/2 + 29^1/2 ]
L = 4.6 ( 12343.75 / 274750 ) ^1/2 * 5.39
L = 1.14 m
two opposite poles repel each other
Answer:
South Pole and South Pole or North Pole and North Pole.
A float valve, regulating the flow of water into a reservoir, is shown in the figure. The spherical float (half of the sphere is submerged) is 0.1553 m in diameter. AOB is the weightless link carrying the float at one end, and a valve at the other end which closes the pipe through which flows into the reservoir. The link is mounted on a frictionless hinge at O, and the angle AOB is 135o. The length of OA is 253 mm and the distance between the center of the float and the hinge is 553 mm. When the flow is stopped AO will be vertical. The valve is to be pressed on to the seat with a force of 10,53 N to be completely stop the flow in the reservoir. It was observed that the flow of water is stopped, when the free surface of water in the reservoir is 353 mm below the hinge at O. Determine the weight of the float sphere.
Answer:
9.29 N . . . . weight of 0.948 kg sphere
Explanation:
The sum of torques on the link BOA is zero, so we have ...
(right force at A)(OA) = (up force at B)(OB·sin(135°))
Solving for the force at B, we have ...
up force at B = (10.53 N)(253 mm)/((553 mm)/√2) ≈ 6.81301 N
This force is due to the difference between the buoyant force on the float sphere and the weight of the float sphere. Dividing by the acceleration due to gravity, it translates to the difference in mass between the water displaced and the mass of the sphere.
∆mass = (6.81301 N)/(9.8 m/s^2) = 0.695205 kg
__
The center of the sphere of diameter 0.1553 m is below the waterline by ...
(553 mm)cos(45°) -(353 mm) = 38.0300 mm
The volume of the spherical cap of radius 155.3/2 = 77.65 mm and height 77.65+38.0300 = 115.680 mm can be found from the formula ...
V = (π/3)h^3(3r -h) = (π/3)(115.680^2)(3·77.65 -115.68) mm^3 ≈ 1.64336 L
So the mass of water contributing to the buoyant force is 1.64336 kg. For the net upward force to correspond to a mass of 0.695305 kg, the mass of the float sphere must be ...
1.64336 kg -0.695205 kg ≈ 0.948 kg
The weight of the float sphere is then (9.8 m/s^2)·(0.948 kg) = 9.29 N
The weight of the 0.948 kg float sphere is about 9.29 N.
For the pipe-fl ow-reducing section of Fig. P3.54, D 1 5 8 cm, D 2 5 5 cm, and p 2 5 1 atm. All fl uids are at 20 8 C. If V 1 5 5 m/s and the manometer reading is h 5 58 cm, estimate the total force resisted by the fl ange bolts.
Answer:
The total force resisted by the flange bolts is 163.98 N
Explanation:
Solution
The first step is to find the pipe cross section at the inlet section
Now,
A₁ = π /4 D₁²
D₁ = diameter of the pipe at the inlet section
Now we insert 8 cm for D₁ which gives us A₁ = π /4 D (8)²
=50.265 cm² * ( 1 m²/100² cm²)
= 5.0265 * 10^⁻³ m²
Secondly, we find cross section area of the pipe at the inlet section
A₂ = π /4 D₂²
D₂ = diameter of the pipe at the inlet section
Now we insert 5 cm for D₁ which gives us A₁ = π /4 D (5)²
= 19.63 cm² * ( 1 m²/100² cm²)
= 1.963 * 10^⁻³ m²
Now,
we write down the conversation mass relation which is stated as follows:
Q₁ = Q₂
Where Q₁ and Q₂ are both the flow rate at the exist and inlet.
We now insert A₁V₁ for Q₁ and A₂V₂ for Q₂
So,
V₁ and V₂ are defined as the velocities at the inlet and exit
We now insert 5.0265 * 10^⁻³ m² for A₁ 5 m/s for V₁ and 1.963 * 10^⁻³ m² for A₂
= 5.0265 * 5 = 1.963 * V₂
V₂ = 12.8 m/s
Note: Kindly find an attached copy of the part of the solution to the given question below
xpress the negative value -22 as a 2's complement integer, using eight bits. Repeat it for 16 bits and 32 bits. What does this illustrate with respect to the properties of sign extension as they pertain to 2's complement representation? 8 bit The 8-bit binary representation of 22 is 00010110. So, -22 in 2’s complement form is (NOT (00010110) + 1) = (11101001 + 1) = 11101010
Answer:
Explanation:
A negative binary number is represeneted by its 2's complement value. To get 2's complement, you just need to invert the bits and add 1 to it. So the formula is:
twos_complement = ~val + 1
So you start out with 22 and you want to make it negative.
22₁₀ = 0001 0110₂
~22₁₀ = 1110 1001₂ inverting the bits
~22₁₀ + 1 = 1110 1010₂ adding 1 to it.
so -22₁₀ == ~22₁₀ + 1 == 1110 1010₂
Do the same process for 16-bits and 32-bits and you'll find that the most significant bits will be padded with 1's.
-22₁₀ = 1110 1010₂ 8-bits
-22₁₀ = 1111 1111 1110 1010₂ 16-bits
-22₁₀ = 1111 1111 1111 1111 1111 1111 1110 1010₂ 32-bits
Water vapor initially at 3.0 MPa and 300°C (state 1) is contained within a piston- cylinder. The water is cooled at constant volume until its temperature is 200°C (state 2). The water is then compressed isothermally to a state where the pressure is 2.5 MPa (state 3).a. Locate states 1, 2, and 3 on a T-v and P-v diagram.b. Determine the specific volume at all three states.c. Calculate the compressibility factor Z at state 1 and comment.d. Find the quality (if applicable) at all three states.
Answer:
a. T-V and P-V diagram are included
b. State 1: Specific volume = 0.0811753 m³/kg
State 2: Specific volume = 0.0811753 m³/kg
State 3: Specific volume = 0.0804155 m³/kg
c. Z = 51.1
d. Quality for state 1 = 100%
Quality for state 2 = 63.47%
Quality for state 3 = 100%
Explanation:
a. T-V and P-V diagram are included
b. State 1: Water vapor
P₁ = 3.0 MPa = 30 bar
T₁ = 300°C = 573.15
Saturation temperature = 233.86°C Hence the steam is super heated
Specific volume = 0.0811753 m³/kg
State 2:
Constant volume formula is P₁/T₁ = P₂/T₂
Specific volume = 0.0811753 m³/kg
T₂ = 200°C = 473.15
Therefore, P₂ = P₁/T₁ × T₂ = 3×473.15/573.15 = 2.4766 MPa
At T₂ water is mixed water and steam and the [tex]v_f[/tex] = 0.00115651 m³/kg
[tex]v_g[/tex] = 0.127222 m³/kg
State 3:
P₃ = 2.5 MPa
T₃ = 200°C
Isothermal compression P₂V₂ = P₃V₃
V₃ = P₂V₂ ÷ P₃ = 2.4766 × 0.0811753/2.5 = 0.0804155 m³/kg
Specific volume = 0.0804155 m³/kg
2) Compressibility factor is given by the relation;
[tex]Z = \dfrac{PV}{RT} = \dfrac{3\times 10^6 \times 0.0811753 }{8.3145 \times 573.15} = 51.1[/tex]
Z = 51.1
3) Gas quality, x, is given by the relation
[tex]x = \dfrac{Mass_{saturated \, vapor}}{Total \, mass} = \dfrac{v - v_f}{v_g - v_f}[/tex]
Quality at state 1 = Saturated quality = 100%
State 2 Vapor + liquid Quality
Gas quality = (0.0811753 - 0.00115651)/ (0.127222-0.00115651) = 63.47%
State 3: Saturated vapor, quality = 100%.
A shell-and tube heat exchanger (two shells, four tube passes) is used to heat 10,000 kg/h of pressurized water from 35 to 120 oC with 5000 kg/h pressurized water entering the exchanger at 300 oC. If the overall heat transfer coefficient is 1500 W/m^2-K, determine the required heat exchanger area.
Answer:
4.75m^2
Explanation:
Given:-
- Temperature of hot fluid at inlet: [tex]T_h_i = 300[/tex] °C
- Temperature of cold fluid at outlet: [tex]T_c_o = 120[/tex] °C
- Temperature of cold fluid at inlet: [tex]T_c_i = 35[/tex] °C
- The overall heat transfer coefficient: U = 1500 W / m^2 K
- The flow rate of cold fluid: m_c = 10,00 kg/ h
- The flow rate of hot fluid: m_h = 5,000 kg/h
Solution:-
- We will evaluate water properties at median temperatures of each fluid using table A-4.
Cold fluid: Tci = 35°C , Tco = 35°C
Tcm = 77.5 °C ≈ 350 K --- > [tex]C_p_c = 4195 \frac{J}{kg.K}[/tex]
Hot fluid: Thi = 300°C , Tho = 150°C ( assumed )
Thm = 225 °C ≈ 500 K --- > [tex]C_p_h = 4660 \frac{J}{kg.K}[/tex]
- We will use logarithmic - mean temperature rate equation as follows:
[tex]A_s = \frac{q}{U*dT_l_m}[/tex]
Where,
A_s : The surface area of heat exchange
ΔT_lm: the logarithmic differential mean temperature
q: The rate of heat transfer
- Apply the energy balance on cold fluid as follows:
[tex]q = m_c * C_p_c * ( T_c_o - T_c_i )\\\\q = \frac{10,000}{3600} * 4195 * ( 120 - 35 )\\\\q = 9.905*10^5 W[/tex]
- Similarly, apply the heat balance on hot fluid and evaluate the outlet temperature ( Tho ) :
[tex]T_h_o = T_h_i - \frac{q}{m_h * C_p_h} \\\\T_h_o = 300 - \frac{9.905*10^5}{\frac{5000}{3600} * 4660} \\\\T_h_o = 147 C[/tex]
- We will use the experimental results of counter flow ( unmixed - unmixed ) plotted as figure ( Fig . 11.11 ) of the " The fundamentals to heat transfer" and determine the value of ( P , R , F ).
- So the relations from the figure 11.11 are:
[tex]P = \frac{T_c_o - T_c_i}{T_h_i - T_c_i} \\\\P = \frac{120 - 35}{300 - 35} \\\\P = 0.32[/tex]
[tex]R = \frac{T_h_i - T_h_o}{T_c_o - T_c_i} \\\\R = \frac{300 - 147}{120 - 35} \\\\R = 1.8[/tex]
Therefore, P = 0.32 , R = 1.8 ---- > F ≈ 0.97
- The log-mean temperature ( ΔT_lm - cf ) for counter-flow heat exchange can be determined from the relation:
[tex]dT_l_m = \frac{( T_h_i - T_c_o ) - ( T_h_o - T_c_i ) }{Ln ( \frac{( T_h_i - T_c_o )}{( T_h_o - T_c_i )} ) } \\\\dT_l_m = \frac{( 300 - 120 ) - ( 147 - 35 ) }{Ln ( \frac{( 300-120 )}{( 147-35)} ) } \\\\dT_l_m = 143.3 K[/tex]
- The log - mean differential temperature for counter flow is multiplied by the factor of ( F ) to get the standardized value of log - mean differential temperature:
[tex]dT_l = F*dT_l_m = 0.97*143.3 = 139 K[/tex]
- The required heat exchange area ( A_s ) can now be calculated:
[tex]A_s = \frac{9.905*10^5 }{1500*139} \\\\A_s = 4.75 m^2[/tex]
