a point charge a of 13.0 3 1027 coulomb is placed 2.0 3 1022 meter from a second point charge b of 14.0 3 1027 coulomb. calculate the magnitude of the electrostatic force that charge a exerts on charge b.

The resistance of a similar wire made of aluminum is higher than the resistance of the copper wire. This is because aluminum has a higher resistivity than copper.

The resistance of a wire depends on its length, cross-sectional area, and the resistivity of the material it's made of. The resistivity of copper is [tex]1.68 x 10^-8 Ωm[/tex] , while the resistivity of aluminum is [tex]2.65 x 10^-8 Ωm.[/tex]

To calculate the resistance of the copper wire, we first need to calculate its cross-sectional area. The diameter of the wire is 0.5mm, so its radius is 0.25mm (or 0.00025m). The cross-sectional area of the wire is therefore:

[tex]A = πr^2 = π(0.00025)^2 = 1.96 x 10^-7 m^2[/tex]

The length of the wire is 7.5m. Therefore, the resistance of the copper wire is:

[tex]R = ρL/A = (1.68 x 10^-8 Ωm)(7.5m)/(1.96 x 10^-7 m^2) = 0.644 Ω[/tex]

To calculate the resistance of a similar wire made of aluminum, we can use the same formula but with the resistivity of aluminum. The diameter of the wire is the same, so its cross-sectional area is also the same. The length of the wire is also the same, so the resistance of the aluminum wire is:

[tex]R = ρL/A = (2.65 x 10^-8 Ωm)(7.5m)/(1.96 x 10^-7 m^2) = 0.819 Ω[/tex]

for such more question on Resistance

brainly.com/question/25997303

#SPJ4

A particle with a mass of m/2 and a charge of 2q has kinetic energy of 2K when it is propelled from rest by the same potential difference.

Due to the fact that mass has no impact on kinetic energy, W = K = QV. where,  

charge = Q, q

V = potential difference

k = kinetic energy

m = mass

The kinetic energy of a particle with a 2q charge and a v potential difference is given by the equation K = Q V,

where,

K₁ = Q₁V₁

K¹ = 2Q¹ x V¹ = 2(QV).

Due to K = QV, K1 = 2K is obtained by substituting K = QV into 2(QV).

Applying the equation E = (k)(q/r²), If q becomes 2q and r becomes 2r, When an electric charge is present in a specific region of space, its properties are altered and an electric field is generated. The term electric field refers to the physical field that surrounds electrically charged particles and acts to either attract or repel other charged particles in the field.

To know more about charges:

https://brainly.com/question/13533739

#SPJ4

To find the equivalent resistance of a circuit, the circuit topology has to be considered, the values of the individual resistors, and how they are connected.

The equivalent resistance of a circuit is the single resistor that would replace all the resistors in the circuit and produce the same overall resistance as the original circuit.

In other words, when  the equivalent resistance of a circuit is calculated, the resistance of a single resistor could be found that would cause the same amount of current to flow through the circuit when the same voltage is applied as the original circuit. This single resistor is a theoretical construct and in reality, one would need to use multiple resistors to achieve the same overall resistance.

The equivalent resistance depends on the topology of the circuit, the values of the individual resistors, and how they are connected. For simple circuits, the equivalent resistance can be calculated using the formulas for resistors in series, resistors in parallel, or a combination of both. For more complex circuits, computer simulations or experimental measurements may be necessary to determine the equivalent resistance.

To know more about equivalent resistance of a circuit, visit:

https://brainly.com/question/12856032

#SPJ4

The frequency of alternating current (AC) is the number of times the current changes direction per second. It is measured in hertz (Hz).

In most parts of the world, the frequency of alternating current (AC) is 50 Hz, meaning that the current changes direction 50 times per second. However, in some parts of the world, such as the United States and Canada, the frequency of AC is 60 Hz. This means that the current changes direction 60 times per second. It is important to note that the frequency of AC is determined by the power source, and cannot be changed by the user.

Learn more about alternating current (AC): https://brainly.com/question/30715089

#SPJ11

V=3.39×10⁶ ×d for 0≤d≤0.005 m, 7.73x10⁷ m/s is the electric potential at a location 8.0mm from the negative plate, 3.0mm from the positive plate

a. Identify the unknown:

The potential everywhere

List the Knowns:

Charge density of the two plates: σ = ±30×10⁻⁶ C/m²

Distance between the two plates: d=5×10⁻³  m

Permittivity of free space: ε₀=8.85×10⁻¹² C²/N⋅m²

Set Up the Problem:

Since the σ are equal and opposite, this means that in the region outside of the two plates, the electric fields cancel each other out to zero: E = 0 The electric field between the plates is this strong:

E = σ/ε₀ = 30×10⁻⁶/8.85×10⁻¹² = 3.39x10⁶N/C

Possible variations between the positive plate and the negative plate include:

ΔV=Ed=3.39×10⁶ ×0.005=1.7×10⁴ V

Assuming the negatively charged plate is at the origin (d=0) and has no potential, the electric field is directed away from the positively charged plate and towards the negatively charged plate, the positive plate is at (d=+0.005 m) and have 1.7×10⁴ V

Solve the Problem:

V=0 for d<0

V=3.39×10⁶×d for 0≤d≤0.005 m

V=1.7×10⁴ V for d>0.005m

b. Identify the unknown:

when an electron leaves a state of rest at the negative plate and strikes the positive plate, how quickly it moves

List the Knowns:

Electron charge: e=1.6×10⁻¹⁹ C

Electron mass: m=9.11×10⁻³¹ kg

Set Up the Problem:

Potential and electric potential energy have the following relationships: = U/q

U=qV

To move the drop, this potential energy is converted to kinetic energy:

1/2mv²=qV

v = √2qV/m

Solve the Problem:

v = √(2×1.6×10⁻¹⁹×1.7×10⁴/9.11×10⁻³¹) = 7.73x10⁷ m/s

Learn more about Electric potential here:

https://brainly.com/question/12645463

#SPJ4

From the information provided, the energy lost to friction if the motorcycle only gains an altitude of 21 m before coming to rest is approximately 65,954.64 J.

To calculate the energy lost to friction, we need to first determine the initial total mechanical energy of the motorcycle and the final total mechanical energy of the motorcycle after it has climbed to a height of 21 meters and come to rest. The difference between the initial and final energies will give us the energy lost to friction.

The initial total mechanical energy of the motorcycle is given by:

Ei = (1/2)mv² + mgh + 2(1/2)Iw²

where m is the mass of the motorcycle, v is its initial speed, h is the height it climbs, g is the acceleration due to gravity, I is the moment of inertia of the wheels, and w is their initial angular velocity.

We need to calculate the moment of inertia of each wheel:

I = (1/2)mr²

where m is the mass of the wheel and r is its radius. Substituting the given values, we get:

I = (1/2)(12 kg)(0.33 m)² = 0.6534 kg m²

The initial angular velocity of each wheel is not given, so we can assume that it is initially at rest (i.e., w = 0).

Substituting the given values into the equation for E, we get:

Ei = (1/2)(180 kg)(25 m/s)² + (180 kg)(9.81 m/s²)(36 m) + 2(1/2)(0.6534 kg m²)(0)²

= 101,812.44 J

The final total mechanical energy of the motorcycle is given by:

Ef = mgh

where m, g, and h are as before, and the speed and rotational energy of the wheels are both zero.

Substituting the given values, we get:

Ef = (180 kg)(9.81 m/s²)(21 m) = 35,857.8 J

The energy lost to friction is the difference between the initial and final energies:

Energy lost = Ei - Ef = 101,812.44 J - 35,857.8 J = 65,954.64 J

Question - Suppose a 180 kg motorcycle is heading toward a hill at aspeed of 25 m/s. The two wheels weigh 12 kg each and are each annular rings with an inner radius of 0.280 m and an outer radius of 0.330 m. Randomized Variables m 180 kg ˇ-25 m/s h 36 m. how much energy is lost to friction if the motorcycle only gains an altitude of 21 m before coming to rest?

Learn more about energy here: brainly.com/question/25959744

#SPJ4

0.67m from the top of the rod is the center of mass of the system located which is 0.65m long and 0.86kg.

Given the length of rod (d1) = 0.65m

The mass of rod (m1) =  0.86kg

The mass of sphere (m2) = 1.2kg

The distance from the top of the rod to the center of mass of the system can be found using the following equation:

Distance from the top of the rod to the center of mass = (m1*d1 + m2*d2) / (m1 + m2) where m1 is the mass of the rod, d1 is the length of the rod, m2 is the mass of the sphere, and d2 is the distance from the top of the rod to the center of the sphere.

Substituting the given values, we get:

Distance from the top of the rod to the center of mass =

[tex](0.86 * 0.65 + 1.2 * 0.65) / (0.86 + 1.2) = 0.67 m[/tex]

Therefore, the distance from the top of the rod to the center of mass of the system is 0.67 m.

To learn more about center of mass click here https://brainly.com/question/28996108

#SPJ4

The analog cathode ray oscilloscope in the lab manual is related to the digital oscilloscope used in the lab in the same way that 1950s era television is related to modern flat-screen television.

Analog cathode ray oscilloscope and the 1950s era television are older technologies that use cathode ray tube (CRT) to display images or waveforms.

They operate by deflecting an electron beam on a phosphorescent screen to create visual display. And, in contrast, digital oscilloscope and modern flat-screen televisions use digital processing and display technologies to provide more precise and flexible visual representations.

To know more about cathode ray oscilloscope, refer

https://brainly.com/question/19068098

#SPJ1

Answer:

44.7 meter per second

Explanation:

The formula to find velocity is

V = (2 · KE / m)^1/2

V = velocity

KE = Kinetic energy

m = mass

Let's calculate

(2 · 10000 / 10) ^1/2 = 44.7 meter per second

The force of friction between the ball and the grass is 309.98 N.

What is Friction?

It occurs as a result of the microscopic irregularities on the surfaces that interlock and resist relative motion. The amount of friction between two surfaces depends on factors such as the nature of the surfaces in contact, the force pressing the surfaces together, and the relative speed between the surfaces. Friction can be beneficial in some situations, such as in walking or driving a car, but it can also be a hindrance in others, such as in machines where it causes wear and tear on moving parts.

To calculate the force of friction, we can use the formula:

Friction force = coefficient of friction × normal force

The normal force is the force that the ground exerts on the ball and is equal to the weight of the ball, which is:

Weight = 21.79 kg × 9.81 m/s^2

Weight = 213.68 N

So, the normal force is 213.68 N.

Now we can calculate the friction force:

Friction force = 1.45 × 213.68 N

Friction force = 309.98 N

Therefore, the force of friction between the ball and the grass is 309.98 N.

Learn more about Friction from given link

https://brainly.com/question/24338873

#SPJ1

Replacing PVC rod with semiconductor material, its behavior would depend on specific properties. To inject energy we can apply a voltage.

If we replaced the PVC rod with a semiconductor material, the behavior of the rod would depend on the specific properties of the semiconductor. Semiconductors have a unique property called the bandgap, which is the energy difference between the highest occupied energy level (valence band) and the lowest unoccupied energy level (conduction band). When an external energy source, such as heat or light, is applied to a semiconductor, it can promote electrons from the valence band to the conduction band, creating a flow of free electrons that can conduct electricity.

To inject energy into the bound charges in the semiconductor and force it to act more like a conductor, we could use several mechanisms. One common approach is to apply a voltage across the semiconductor, which creates an electric field that can promote electron movement. Another approach is to expose the semiconductor to light, which can excite electrons to higher energy levels and promote conduction. Additionally, thermal energy can cause the semiconductor to act more like a conductor by promoting electron movement. These mechanisms can be used to tailor the conductivity of semiconductors, which is the foundation of many modern technologies such as transistors, solar cells, and light-emitting diodes (LEDs).

Learn more about semiconductor here:

https://brainly.com/question/19618939

#SPJ4

"Comets tend to be faster than asteroids, and it is estimated that there are far more large comets than large asteroids." Correct option is B.

As comets typically originate from farther out than asteroids do, they move at faster speeds when they cross Earth's orbit: An asteroid would need to be larger than 10 kilometres in diameter, whereas a comet would only need to be about 7 kilometres in diameter to hit Earth with enough energy to form Chicxulub crater.

Two factors that differentiate a comet from an asteroid are shape of the orbit and chemical composition.

There are asteroids that are spherical, curved, and even have satellites. A comet circles the Sun similarly to an asteroid, but unlike an asteroid, it is made of ice and dust. Therefore, a comet's ice and dust composition begin to vaporise as it approaches the Sun. Consequently, a comet looks fuzzy and/or has a tail when viewed through a telescope.

To know more about asteroids:

https://brainly.com/question/1939309

#SPJ4

The actions which does not affect the value of the capacitance of a parallel plate capacitor is doubling the voltage difference between the plates and doubling the distance between them.

A capacitor is a two-terminal electrical device that can store energy in the form of an electric charge. It consists of two electrical operators that are separated by a distance. The space between the operators may be filled by vacuum or with an separating material known as a dielectric. The capability of the capacitor to store charges is known as capacitance.

Capacitors store energy by holding piecemeal dyads of contrary charges. The simplest design for a capacitor is a resemblant plate, which consists of two essence plates with a gap between them. But, different types of capacitors are manufactured in numerous forms, styles, lengths, circumferences, and accoutrements .

Learn more about Capacitors:

https://brainly.com/question/24242435

#SPJ4

It is true that the maximum speed of a block in a trajectory occurs at its maximum height, where the vertical component of the velocity is zero. This is due to the fact that at that point, the kinetic energy is minimized and the acceleration is zero. At this point, the block is at its highest point, and the velocity of the block is at its lowest. Therefore, the speed is zero at the top of the trajectory.

However, the horizontal component of the velocity is not zero at the maximum height. This is because the block is constantly subject to horizontal acceleration by gravity, even at its highest point. This means that the block has a nonzero velocity in the horizontal direction, even if it is at its maximum height. Therefore, the block is not at rest at the highest point; it is just moving horizontally at a constant speed.

a) The claim student can make is - We can't know for sure whether or not the mass changed, but it seems reasonable to claim that the mass did not change, given that the ranges of uncertainity overlap.

b)  increasing the sample size will in general - increase precision but will not improve accuracy.

c) incorrect results of using the stretched out tape measure- This is due to systematic error. Assuming that a new tape is more accurate, compare the stretched tape to a new tape to see how much the measurements are off. This difference will tell you how much to correct each original length measurement causing the systematic error to be minimized.

a) Since the pupil used the same electronic balance with an query of0.05 g to weigh the mass of the result ahead and later, we can say that the millions are the same within the query of the balance.

b) Precision is the degree to which unborn measures yield the same results. delicacy, on the other hand, is a measure of how nearly the results agree with a true value. By adding the sample size the standard error is dropped meaning that unborn measures will probably fall near to the average. However, also taking further measures won't address this error and ameliorate delicacy as each dimension will be" off" by the same quantum from the true value, If methodical error is present. rather the methodical error needs to be removed, if possible, and this will ameliorate delicacy.

c) The stretching of the tape recording measure introduces a methodical error which could be corrected by comparing the tape recording with a different tape recording( essence or new). Once the pupil knows how important each dimension is out, the pupil can acclimate the original measures consequently. Performing further measures simply reduces the arbitrary error caused by the person reading the scale and won't affect the delicacy of the dimension.

Learn more about Experiment questions;

https://brainly.com/question/28657547

#SPJ4

In physics, a collision is an event in which two or more bodies come together in a direct physical contact and exert forces on each other for a relatively short time. During a collision, there is a transfer of energy and momentum between the colliding bodies.

Describe Collision?

There are two types of collisions: elastic and inelastic. In an elastic collision, kinetic energy is conserved, meaning that the total kinetic energy of the system before the collision is equal to the total kinetic energy after the collision. In an inelastic collision, kinetic energy is not conserved, and some of the kinetic energy is transformed into other forms of energy, such as heat or sound.

Collisions can occur between objects of any size, from subatomic particles to astronomical bodies like stars and planets. They are important in various fields of study, such as mechanics, astrophysics, and particle physics. Understanding the physics of collisions is essential for designing safety devices, analyzing traffic accidents, and predicting the behavior of complex systems.

To solve this problem, we can use the conservation of momentum and the fact that the velocity of the center of mass of the two-car system remains constant before and after the collision.

(a) Before the collision, the velocity of car 1 is v01 = +0.68 m/s, and the velocity of car 2 is v02 = +1.4 m/s. The velocity of the center of mass of the two-car system is given by:

v0 = (m1v01 + m2v02) / (m1 + m2)

= (65 ✕ 103 kg ✕ 0.68 m/s + 92 ✕ 103 kg ✕ 1.4 m/s) / (65 ✕ 103 kg + 92 ✕ 103 kg)

= 1.06 m/s

Therefore, the velocity of their center of mass before the collision is 1.06 m/s.

(b) After the collision, the two cars stick together and move with a common velocity vf. The momentum of the system is conserved, so:

m1v01 + m2v02 = (m1 + m2)vf

We can solve for vf:

vf = (m1v01 + m2v02) / (m1 + m2)

= (65 ✕ 103 kg ✕ 0.68 m/s + 92 ✕ 103 kg ✕ 1.4 m/s) / (65 ✕ 103 kg + 92 ✕ 103 kg)

= 1.12 m/s

Therefore, the velocity of their center of mass after the collision is 1.12 m/s.

(c) The velocity of the center of mass of the two-car system remains the same before and after the collision, so it is equal to 1.06 m/s. Since the velocity of the coupled cars after the collision is 1.12 m/s, which is greater than 1.06 m/s, our answer in part (b) is greater than the common velocity of the two coupled cars.

To know more about mass visit:

brainly.com/question/28704035

#SPJ1

The volumetric average fluid velocity (m/s) through the valve of ball valve having energy loss as 240 j/kg is 15.5 m/s.

When energy is converted from one form to another, or moved from one place to another, or from one system to another there's energy loss. This means that when energy is converted to a different form, some of the input energy is turned into a largely disordered form of energy, like heat.

Flow rate is the volume of fluid per unit time flowing past a point through the area A. Then the shadowed cylinder of fluid flows once point P in a invariant pipe in time t. The volume of the cylinder is announcement and the average haste is v =d / t so that the inflow rate is Q = announcement/ t = Av.

Energy loss is given as 240 J/kg

So to find the volumetric average velocity we have,

Energy loss = 1/2 V² J/kg

240 = 1/2 V² J/kg

V = [tex]\sqrt{240}[/tex]

V = 15.49 ≈ 15.5 m/s

Therefore,  the volumetric average fluid velocity  is V = 15.49 ≈ 15.5 m/s.

Learn more about Volumetric fluid velocity:

https://brainly.com/question/29677488

#SPJ4

The time taken to reach the top speed of the 80 lm/ hours, starting from the rest is 55.17 seconds.

We have rate = 1.45 and final velocity is  80

The formula to find the acceleration is,

a = v - u/t

t = v-u/a

Where, u = initial velocity

v = final velocity

a = acceleration

t = time taken

so,

t = 80 - 0/1.45

= 80/1.45

= 55.17 seconds

Then v is the final haste, u is the original haste, a is the acceleration and t is the time interval during which a body is under acceleration.

Learn more about Time taken:

https://brainly.com/question/13449733

#SPJ4

To measure and calculate the vertical momentum of the two-puck system before the collision.

Initial momentum = (mass of top puck + mass of bottom puck) x initial velocity

Substituting the values we have:

Initial momentum = (0.1 kg + 0.2 kg) x 2 m/s

Initial momentum = 0.3 kg x 2 m/s

Initial momentum = 0.6 kg m/s

Therefore, the vertical momentum of the two-puck system before the collision is 0.6 kg m/s.

When two or more objects come into contact with one another and exchange energy, momentum, or other physical properties, the occurrence is called a collision. Depending on the nature of the items involved and how they interact with each other during the impact, a collision in physics can be either elastic or inelastic.

The complete kinetic energy of the colliding objects is preserved in an elastic collision, which means that none of the kinetic energy is converted into other kinds of energy like heat or sound. The items in this kind of collision bounce off one another with the same velocity and direction as before the collision.

On the other hand, in an inelastic collision, some or all of the kinetic energy of the colliding objects is transformed into other types of energy, such heat, sound, or object deformation. In this kind of collision, the items may cling together after impact or bounce off one another in a different direction or at a different speed than previously.

To know more about collision, visit:

https://brainly.com/question/24915434

#SPJ4

In a vacuum, the Velocity of ALL forms of electromagnetic radiation remains constant. In contrast to mechanical waves, electromagnetic waves may travel without a medium.

This indicates that electromagnetic waves are capable of passing not just through solid objects like air and rock but also through a vacuum like space.

At the speed of light (2.998 108 m/s), electromagnetic radiation is an electric and magnetic disturbance that travels through space. It moves in radiant energy packets called photons or quanta and has neither mass nor charge. X-rays, infrared, ultraviolet, gamma, and radio waves are all types of electromagnetic radiation. The sun and other celestial bodies, radioactive substances, and man-made gadgets are some examples of sources of EM radiation. EM displays both a wave and a particle nature.

The medium's electric and magnetic characteristics affect the velocity of electromagnetic waves.

Learn more about Velocity here:

https://brainly.com/question/30559316

#SPJ4

The best evidence that a substance's appearance can be significantly altered by both chemical and physical changes is the combination of examples 1 and 3.

Option A is correct.

A substance undergoes a change in its physical characteristics when it undergoes a physical change. Most of the time, a physical change can be reversed. In the course of such a transformation, no chemical substance is produced.

Chemical changes include processes like burning, frying, rusting, and rotting. The processes of melting, freezing, shredding, and boiling are all examples of physical modifications. The majority of physical symptoms can be reversed with enough energy.

Learn more about Chemical changes :

brainly.com/question/16768723

#SPJ1

There is some scientific evidence to suggest that vibration at certain frequencies can affect visual perception, but the claim that vision is blurred if the head is vibrated at 29 Hz because the vibrations are resonant with the natural frequency of the eyeball held by the musculature in its socket is not entirely accurate.

According to the concept of "eyeball resonance," the eyeball can vibrate at specific frequencies as a result of the tension in the muscles around it, and these vibrations can affect vision. Generally speaking, the natural frequency of the eyeball is thought to be around 20 Hz, however this frequency can change based on a number of variables, including the eyeball's flexibility and the tension of the optic nerve.

There is some evidence to support the idea that being exposed to vibration at particular frequencies can alter vision. For instance, some researchers have discovered that participants who are exposed to 25 Hz vibration may have a reduction in visual acuity, while other studies have found that those who are exposed to 10 Hz vibration may experience an increase in improve visual perception in some people.

To know more about Eyeball resonance and vision visit:

https://brainly.com/question/12445093

#SPJ4

Answer:

Sarah can travel 80 km in 4 hours at a constant speed of 20 km/h.

Explanation:

The distance that Sarah can travel in 4 hours can be calculated by multiplying her speed (20 km/h) by the time (4 hours):

distance = speed x time

distance = 20 km/h x 4 hours = 80 km

Answer:

80 km

Explanation:

Speed = Distance / Time
20 = Distance / 4
Distance = Speed x Time
Distance = 20 x 4
Distance = 80 km

Hope it helps

Answer: Object's speed affects the Kinetic Energy Quadratically.

Explanation: we have to know that Kinetic Energy is a scalar quantity, that is it doesn't have direction. Kinetic Energy of a moving body is totally dependent upon the body's mass and velocity of it.

The Kinetic Energy of a moving body having mass M and velocity V, then at a certain instant, the body's having Kinetic Energy is equal to:

Kinetic Energy (K.E.) = (MV²)/2

where:

M⇒ Body's mass

V ⇒Velocity of a moving body

It is so Clear that K.E. directly proportional to square of the body's velocity.

Therefore, Object's speed affects the Kinetic Energy Quadratically.

Know more about Kinetic Energy:

brainly.com/question/2548537

The student can place the bar magnet near the known pole of a second magnet and observe the interaction between the poles.

option D.

When two magnets are brought near each other, the direction of the magnetic field lines can be used to determine the orientation of the poles.

If the two magnets are brought near each other with the same poles facing each other (north-north or south-south), they will experience a repulsive force and will push away from each other.

On the other hand, if the magnets are brought near each other with opposite poles facing each other (north-south), they will experience an attractive force and will move towards each other.

Learn more about poles of magnet here: https://brainly.com/question/14997726

#SPJ1

Answer:

The statement "These wavelengths form the infrared part of the spectrum." best describes wavelengths of sunlight that are longer than 700 nanometers. Infrared light is a type of electromagnetic radiation with longer wavelengths than visible light, but shorter wavelengths than radio waves. It is typically defined as having wavelengths between 700 nanometers and 1 millimeter.

If a meteor with a 20 m in diameter impacts Earth on land, approximately the crater will be 200-400m in diameter long.

The size of the crater created by a meteorite impact depends on several factors, such as the composition of the meteorite and the density of the material it impacts. Generally speaking, a 20 m in diameter meteorite would create a crater with a diameter between 200 and 400m. A few meters to several hundred meters can make up the crater's depth.  A crater will most likely be created at the point of impact when a meteor impacts a planet. The size of the crater will increase as the object moves faster and becomes larger or heavier. The biggest predictors of impact crater size are the meteor's mass and velocity.

To learn more about density click here https://brainly.com/question/943734

#SPJ4

Answer:

I think about 70.

Explanation:

I hope I helped

The ground is chosen as a base for potential gravitational energy for the same reason. Compared to the gravitational potential at the center of the planet, the truth is that you even have gravitational potential energy.

Ep = mgh. An object has the same amount of stored gravitational potential energy as the work required to raise it. The gravitational potential energy (PEg) that is added to or obtained by the object-Earth system is how we describe this.

The force acting on the two objects affects the formula for potential energy. P.E. = mgh is the formula for gravitational force, where m is mass in kilograms, g is acceleration due to gravity (9.8 m/s2 at the earth's surface), and h is height in meters.

M= 2kg

P.E = 40j

g=10N

H=?

Using formula [tex]P.E. = mgh[/tex]

40 = 2 * 10* H

Therefore, approximately 2 meters it is above the ground.

Learn more about potential energy here:

https://brainly.com/question/24284560

#SPJ4

So the force between the two charges would be 8.99 x 10^3 newtons.

define force ?

Force is a physical quantity that describes the interaction between objects or systems, causing a change in motion or deformation. It is typically measured in newtons (N) and is represented as a vector quantity with both magnitude and direction.

The force between two charges can be calculated using Coulomb's law:

F = kq1q2 / r^2

where k is Coulomb's constant (k = 8.99 x 10^9 N m^2/C^2), q1 and q2 are the charges of the two objects, and r is the distance between them.

In this case, q1 = q2 = 1 C, and r = 1 km = 1000 m. Plugging these values into the equation, we get:

F = (8.99 x 10^9 N m^2/C^2) * (1 C) * (1 C) / (1000 m)^2

= 8.99 x 10^3 N

So the force between the two charges would be 8.99 x 10^3 newtons.

To learn more about force follow the given link: https://brainly.com/question/27872232

#SPJ4