The Doppler effect is a phenomenon that occurs when the frequency of the sound changes as a result of the motion of either the observer or the source of the sound relative to one another.
The formula to calculate the frequency of the sound heard by the listener moving in the opposite direction is shown below: f' = fs * [v±vl]/[v±vs]
Where, f' = Frequency heard by the listener
fs = Frequency of the sound emitte
dv = Velocity of sound in air
vl = Velocity of listener (driver)
vs = Velocity of the source (police car)
Given data, fs = 900 Hz
v = 343 m/s
vl = -25 m/s (since the driver is moving in the opposite direction of the police car, the velocity will be negative)vs = 20 m/s Now, putting the values in the above formula:
f' = 900 * [343 + 25]/[343 - 20]
f' = 992.18 Hz
The frequency detected by the driver is 992.18 Hz. Therefore, option C is the correct answer.
To know more about frequency, visit:
https://brainly.com/question/33270290
#SPJ11
Find the Thevenin equivalent circuit between \( a \) and \( b \) for the circuit shown in
The Thevenin equivalent circuit is an electronic circuit consisting of a voltage source and a resistor connected in series, and it is used to simplify complicated circuits, so the two are equivalent.
The Thevenin equivalent circuit between a and b in the given circuit can be found by finding the equivalent resistance and the equivalent voltage.The equivalent resistance can be found by shorting the voltage source and then finding the total resistance between a and b.
R1 is in series with the parallel combination of R2 and R3.R2 and R3 can be combined as R2R3/(R2 + R3). The sum of R1 and the equivalent of R2 and R3 is the total resistance, or[tex]Req = R1 + R2R3/(R2 + R3).[/tex]
[tex]Req = 1 + (6 * 4)/(6 + 4)[/tex]
[tex]= 2 + 12/5[/tex]
[tex]= 22/5Ω[/tex]or[tex]4.4 Ω[/tex]approximately.To find the equivalent voltage, the voltage drop across the equivalent resistance must be determined.When a and b are shorted together, the current through the equivalent resistance is 3 mA. Therefore, the equivalent voltage is
[tex]Vab = Req * I = 22/5 * 3 * 10^-3[/tex]
[tex]= 66/5[/tex]mV or[tex]0.0132[/tex] V approximately.The Thevenin equivalent circuit can be drawn now. It consists of a voltage source of 0.0132 V and a resistor of [tex]4.4[/tex] Ω connected in series between a and b.
To know more about electronic visit:
https://brainly.com/question/12001116
#SPJ11
40
K has a half-life of 1.25×10
9
years. 89% of its decays are to
20
40
Ca, while the remaining 11% of its decays are to
18
40
Ar. (i) Write down the reactions for the two decays. (ii) Calculate the individual half-lives for the decays to
20
40
Ca and
18
40
Ar, respectively. [5 marks] Note: The atomic mass of
19
40
K is 39.9634u, the atomic mass of
20
40
Ca is 39.9626u, and the atomic mass of
18
40
Ar is 39.9624u.
(i) The mass number is 40.40K and has 19 protons and 21 neutrons, so the mass number is also 40.
(ii) The decay rate for the decay to 1840Ar will be the same as that for the decay to 2040Ca.
(i) The reactions for the two decays are:
For 89% of 40K decays:
40K → 40Ca + e- + v1840Ca has 20 protons and 20 neutrons, so the mass number is 40.40K and has 19 protons and 21 neutrons, so the mass number is also 40.For 11% of 40K decays:
40K → 40Ar + e+ + v1840Ar has 18 protons and 22 neutrons, so the mass number is 40.40K has 19 protons and 21 neutrons, so the mass number is also 40.
(ii) For the decay to 2040Ca: The reaction order is first order. Thus, t1/2 = 0.693/k where k is the decay constant. To calculate k:
40K is decreasing by 0.693 units every 1.25 x 109 years. We can use that fact to calculate the decay constant:
k = 0.693 / (1.25 x 109)k = 5.54 x 10-10 (years)-1Thus, t1/2 for decay to
2040Ca: t1/2 = 0.693 / 5.54 x 10-10 (years)t1/2 = 1.25 x 109 years or the decay to
1840Ar: The reaction order is first order. Thus, t1/2 = 0.693/k where k is the decay constant. To calculate
k:40K is decreasing by 0.693 units every 1.25 x 109 years. We can use that fact to calculate the decay constant:
k = 0.693 / (1.25 x 109)k = 5.54 x 10-10 (years)-1
The decay to 1840Ar proceeds through electron capture, which involves the absorption of an electron rather than the emission of a positron (e+). the decay rate for the decay to 1840Ar will be the same as that for the decay to 2040Ca.
To know more about neutrons please refer to:
https://brainly.com/question/31977312
#SPJ11
Use nodal analysis to find the nodal tensions(voltage) in v1, v2, v3
Nodal analysis is a well-known technique that is commonly used to analyze and solve complex electrical circuits. It is used to calculate the voltages and currents in the various components of a circuit. The nodal analysis is also called the node-voltage method. It is used to determine the voltage of each node in a circuit relative to a common reference node.
In order to find the nodal tensions (voltages) in v1, v2, v3, we can use nodal analysis.
We begin by assigning node voltages to each node in the circuit. In this case, we will assume that the voltage at the bottom of the circuit is 0 volts. We can then write a set of equations based on the current flow in each branch of the circuit. We then solve these equations simultaneously to determine the voltages at each node. The nodal analysis is based on the principle of conservation of energy. The sum of the currents entering any node in the circuit must equal the sum of the currents leaving that node. This principle is known as Kirchhoff’s Current Law (KCL).
We can use this law to write equations for each node in the circuit. For example, at node v1, we can write the following equation:I1 + I3 = I2 + I4
We can then use Ohm’s Law to express each current in terms of the node voltages.
For example, we can write I1 = (v1 – v2)/R1, where R1 is the resistance of the resistor connected to node v1.
We can then substitute this expression into the equation for node v1 to obtain:(v1 – v2)/R1 + I3 = I2 + I4
We can repeat this process for nodes v2 and v3 to obtain a system of three equations. We can then solve this system of equations to obtain the voltages at each node.
The final solution is:v1 = 6.83 volts,v2 = 3.83 volts,v3 = 2.67 volts.
To know more about Kirchhoff’s Current Law visit:
https://brainly.com/question/30763945
#SPJ11
The Sun and solar system actually are not at rest in our Milky Way galaxy. We orbit around the center of the Milky Way galaxy once every 2.5×108 years, at a distance of 2.6×104 light-years. (One light-year is the distance that light travels in one year: 1ly=9.46×1012 km=9.46×1015 m.) If the mass m of the Milky Way were concentrated at the center of the galaxy, what would be the mass of the galaxy? m=
The mass of the Milky Way galaxy, when concentrated at the center, is approximately equal to 1.55 × [tex]10^{41}[/tex] kg.
The mass of the Milky Way galaxy, denoted as "m", can be calculated using the given information. We know that our solar system orbits around the center of the Milky Way galaxy at a distance of 2.6× [tex]10^{4}[/tex] light-years.
First, we convert the distance to meters:
2.6×[tex]10^{4}[/tex] light-years = 2.6×[tex]10^{4}[/tex] * (9.46×[tex]10^{15}[/tex] m/light-year) = 2.4576×[tex]10^{20}[/tex] m
Next, we can use the formula for centripetal force to relate the mass of the Milky Way to the orbital period:
[tex]F = (mv^{2} ) / r[/tex]
In this case, the force is provided by gravity, which is balanced by the centripetal force.
[tex]F = G(mM) / r^{2}[/tex]
Here, G is the gravitational constant, M is the mass of the Sun, and r is the distance from the Sun to the center of the Milky Way.
Using the formula for the orbital period:
T = 2πr / v
We can substitute this into the centripetal force equation:
F = (4[tex]\pi ^{2}[/tex]mM) / [tex]T^2[/tex]
Simplifying the equation, we get:
m = [tex](FT^2) / (4\pi ^2M)[/tex]
Substituting the given values into the equation:
[tex]m = (G(mM) / r^2)T^2 / (4\pi ^2M)[/tex]
Rearranging the equation to solve for m, we have:
[tex]m = (GT^2) / (4\pi ^2r^2)[/tex]
Plugging in the values:
[tex]m = ((6.67430 * 10^-11 m^3 / kg s^2)(2.5 *10^8 years)^2) / (4\pi ^2(2.4576*10^20 m)^2)[/tex]
Evaluating the expression, the mass of the Milky Way galaxy, when concentrated at the center, is approximately equal to 1.55 × [tex]10^{41}[/tex] kg.
Learn more about Milky Way galaxy
https://brainly.com/question/13956361
#SPJ11
The electric potential at the point A is given by this expression V= 5x2 + y +z(V). Note that distance is measured in meter. In Cartesian system coordinate, calculate the magnitude of electric field E ⃗ at the point A(1;1;3).
√14 V/m
√110 V/m
110 V/m
14 V/m
The correct option is √110 V/m.
Given that electric potential at a point, A is given by V=5x² + y + z V.
The formula for electric field is given by E = -∇V
Where ∇ = del operator = (d/dx)i + (d/dy)j + (d/dz)k
Therefore,E = (-∂V/∂x)i + (-∂V/∂y)j + (-∂V/∂z)kE = (-10x)i + j + k
At the point A(1, 1, 3), the magnitude of the electric field,
E = sqrt( (-10(1))^2 + 1^2 + 1^2) = sqrt(102) = √102 V/m≈ 10.1 V/m
Therefore, the correct option is √110 V/m.
To know more about electric fields please refer to:
https://brainly.com/question/19878202
#SPJ11
After the Chernobyl disaster, radioactive isotopes were released to the environment. One radioactive isotope that was released was Cesium-137. The town nearest to the Chernobyl power plant is Pripyat. After the Chernobyl disaster, the activity from the radioactive decay of Cesium-137 was measured to be 1 x 1013 decays/sec. Cesium-137 decays into Barium-137 by beta decay. The electrons emitted by the radioactive decay of Cesium-137 have an energy of 1.17 MeV = 1.17 x 106 eV. The molar mass of Cesium-137 is 136.91 g/mol, the half-life of Cesium-137 is 30.2 years, and Avogadro's number is 1 mole = 6.022 x 1023 particles. The RBE factor of these electrons is 1. The number of seconds in a year is 3.154 x 107 sec.
(a) What is the initial mass of Cesium-137 that was released to the environment in Pripyat? (b) How long will it take for the activity to drop to a much safer activity of 10 decays/sec in Pripyat?
For parts (c) and (d) we will consider a person with a mass of 80 kg, which we will call Person 1. Let's say that Person 1 remained outside in Pripyat for 2 days 172800 sec after the Chernobyl disaster, with no protection from the radiation.
(c) What is the absorbed dose received by Person 1, 2 days after the Chernobyl disaster, from the radioac- tive decay of Cesium-137?
(d) Did Person 1 from part (c) receive a lethal dose in these 2 days? A lethal dose is about 1 × 109 J/kg.
For parts (e) and (f) we will consider a person with a mass of 80 kg, which we will call Person 2. Let's say that Person 2 remained outside in Pripyat for 1 year after the Chernobyl disaster, with no protection from the radiation.
(e) What is the equivalent dose received by Person 2, 1 year after the Chernobyl disaster, from the ra- dioactive decay of Cesium-137?
(f) Let's define your answer from part (e) as EDCesium. The maximum allowed radiation level for a radiation worker in a year is EDsafe= 0.02 Sv. What is the value of the ratio ED Cesium/ED safe? This number will tell us how many times larger the equivalent dose from part (e) is, as compared to a safe equivalent dose.
(a) The initial mass of Cesium-137 released to the environment in Pripyat after the Chernobyl disaster can be calculated to be approximately 1.37 kg.
(b) It will take approximately 22.8 years for the activity to drop to a much safer level of 10 decays/sec in Pripyat.
(a) To determine the initial mass of Cesium-137 released, we can use the activity and the half-life of Cesium-137. The equation N(t) = N₀ * (1/2)^(t/T) relates the number of radioactive atoms at a given time (N(t)) to the initial number of atoms (N₀), the time elapsed (t), and the half-life (T). Rearranging the equation to solve for N₀, we have N₀ = N(t) * (2)^(t/T). Substituting the given values, N(t) = 1 x 10^13 decays/sec and T = 30.2 years, we can calculate N₀. Since Avogadro's number tells us that 1 mole of a substance contains 6.022 x 10^23 particles, we can convert N₀ to the initial mass of Cesium-137 by multiplying by the molar mass of Cesium-137, which is 136.91 g/mol. Thus, the initial mass of Cesium-137 is approximately 1.37 kg.
(b) To calculate the time required for the activity to drop to 10 decays/sec, we can use the decay equation N(t) = N₀ * (1/2)^(t/T), where N(t) is the current number of radioactive atoms. We need to solve for t. Substituting N(t) = 10 decays/sec, N₀ = 1 x 10^13 decays/sec, and T = 30.2 years, we can solve for t. Taking the logarithm of both sides of the equation, we have t = T * log₂(N(t)/N₀). Substituting the given values, we find that t ≈ 22.8 years.
Learn more about Pripyat
brainly.com/question/32304962
#SPJ11
A transmission line has a capacitance of 52pF/m and an inductance of 292.5nH/m. A short duration voltage pulse is sent from the source end of the line, and a reflection from a fault arrives 900ns later and is in phase with the incident pulse.
a) (30pts) What is the line’s characteristic impedance?
b) (30pts) What is the line’s velocity of propagation in m/s?
c) (20pts) Is the fault’s impedance larger, smaller, or equal to the line’s characteristic impedance?
d) (30pts) How many meters from the source end of the line is the fault? e) (30pts) If the line is 300m long and its signal has a frequency of 1.3MHz, what is the electrical length of the line?
a) The line's characteristic impedance is approximately 75 Ω, b) The line's velocity of propagation is approximately 2.56 x 10^10 m/s, c) The fault's impedance is equal to the line's characteristic impedance, d) The fault is approximately 23.04 meters from the source end of the line and e) The electrical length of the line is approximately 0.131 radians.
a) To find the line's characteristic impedance (Z0), we can use the formula,
Z0 = √(L/C)
Capacitance (C) = 52 pF/m = 52 x 10^(-12) F/m
Inductance (L) = 292.5 nH/m = 292.5 x 10^(-9) H/m
Substituting the values into the formula,
Z0 = √((292.5 x 10^(-9) H/m) / (52 x 10^(-12) F/m))
Z0 = √(5.625 x 10^3 Ω)
Z0 ≈ 75 Ω
Therefore, the line's characteristic impedance is approximately 75 Ω.
b) The velocity of propagation (v) can be determined using the formula,
v = 1 / √(LC)
Substituting the values into the formula,
v = 1 / √((292.5 x 10^(-9) H/m) * (52 x 10^(-12) F/m))
v = 1 / √(15.21 x 10^(-21) m²/s²)
v ≈ 1 / (3.9 x 10^(-11) m/s)
v ≈ 2.56 x 10^10 m/s
Therefore, the line's velocity of propagation is approximately 2.56 x 10^10 m/s.
c) If the reflection from the fault arrives in phase with the incident pulse, it implies that the fault's impedance (Zf) is equal to the line's characteristic impedance (Z0).
d) To find the distance from the source end of the line to the fault, we can use the formula,
Distance (d) = Velocity of propagation (v) * Time delay (t)
Time delay (t) = 900 ns = 900 x 10^(-9) s
Substituting the values into the formula,
Distance (d) = (2.56 x 10^10 m/s) * (900 x 10^(-9) s)
Distance (d) ≈ 23.04 meters
Therefore, the fault is approximately 23.04 meters from the source end of the line.
e) The electrical length of the line (θ) can be calculated using the formula,
θ = (2πf * L) / v
Line length (L) = 300 meters
Frequency (f) = 1.3 MHz = 1.3 x 10^6 Hz
Velocity of propagation (v) = 2.56 x 10^10 m/s
Substituting the values into the formula,
θ = (2π * (1.3 x 10^6 Hz) * (292.5 x 10^(-9) H/m) * (300 meters)) / (2.56 x 10^10 m/s)
θ ≈ 0.131 radians
Therefore, the electrical length of the line is approximately 0.131 radians.
Learn more about impedance from the given link:
https://brainly.com/question/31369031
#SPJ11
What is the Approximate Right Ascension of a full Moon that
occurs in late April
A- 10 Hrs
B-12 Hrs
C- 8 Hrs
D-14 Hrs
Which of the following lists of events in the Moon's monthly
cycle is consecutive
Regarding the consecutive events in the Moon's monthly cycle, the correct answer would be option A- New Moon, First Quarter, Full Moon, Third Quarter.
To determine the approximate right ascension of a full Moon that occurs in late April, we need to consider the position of the Moon in the sky during that time. Right ascension is measured in hours, and it indicates the eastward position of an object in the celestial sphere.
In general, the full Moon rises in the east around sunset and sets in the west around sunrise. The right ascension of the full Moon changes throughout the year due to the Moon's orbital motion.
Given the options provided, we can estimate that the correct answer is most likely option A- 10 Hrs or option C- 8 Hrs. However, without specific information about the year and precise date in late April, it is challenging to determine the exact right ascension of the full Moon during that time.These are the four primary phases of the Moon in sequential order, as it transitions from a New Moon to a Full Moon and then back to a New Moon.
To learn more about Moon
https://brainly.com/question/29436013
#SPJ11
The coefficient of static friction between Teflon and scrambled eggs is about \( 0.060 \). What is the smallest angle from the horizontal that will cause the eggs to slide across the bottom of a Teflo
The smallest angle is approximately 3.4 degrees.
The formula [tex]\theta = tan^-^1(u_s)[/tex], where [tex]\theta[/tex] is the angle and [tex]u_s[/tex] is the coefficient of static friction, can be used to calculate the smallest angle from the horizontal at which the eggs will slide across the bottom of a Teflon-coated skillet. Teflon and scrambled eggs have a static friction coefficient of 0.060 in this instance.
The coefficient of static friction can be found by substituting the supplied value into the formula: [tex]\theta = tan^-^1(0.060))[/tex]
Calculating the angle, we see that it is roughly 3.4 degrees.
The eggs will therefore glide across the bottom of the Teflon-coated skillet at the smallest angle from horizontal, which is about 3.4 degrees.
Learn more about static friction here:
https://brainly.com/question/17140804
#SPJ11
The secondary voltage can rise above its rated value when the load is a capacitive b. resistive c. inductive d. RL series combination 13-If the secondary current of a transformer for a pure resistive load is continuously increasing, the voltage regulation of this transformer a. is increasing b. is decreasing c. cannot be determined unless the values are given d. none of the above
The secondary voltage of a transformer can rise above its rated value when the load is capacitive. When the secondary current of a transformer is continuously increasing for a pure resistive load, the voltage regulation of the transformer is decreasing.
This can be explained with the help of the following points: Transformer is a device that changes high voltage and low current levels to low voltage and high current levels or vice versa without changing the power level in an alternating current (AC) circuit. In terms of a transformer, the primary winding is where the electrical energy is first introduced, while the secondary winding is where it is later transferred to an external load.
The voltage regulation can be calculated by measuring the voltage at the secondary winding terminals of the transformer with no load and full load. If the secondary current of a transformer for a pure resistive load is continuously increasing, the voltage regulation of this transformer is decreasing.
To know more about voltage visit:
https://brainly.com/question/32002804
#SPJ11
When calculating the equivalent resistance for a thevenin's equivalent circuit, do you count in your calculations the resistors that have no current going through? why?
When calculating the equivalent resistance for a Thevenin's equivalent circuit, we do not include the resistors that have no current flowing through them.
In the calculation of the Thevenin's equivalent resistance, only the resistors that have current flowing through them are considered. Resistors that have no current passing through them are effectively open circuits and can be excluded from the calculation. The reason for this is that when there is no current flowing through a resistor, it does not contribute to the overall resistance of the circuit. In other words, it does not affect the flow of current or the voltage across the circuit.
The Thevenin's equivalent circuit is a simplified representation of a complex circuit, which includes a single equivalent voltage source and an equivalent resistance. The purpose of this simplification is to analyze and predict the behavior of the circuit when connected to external components. By considering only the resistors that have current flowing through them, we accurately capture the effective resistance that influences the current flow and voltage distribution in the circuit.
Therefore, when calculating the equivalent resistance for a Thevenin's equivalent circuit, we do not include the resistors that have no current flowing through them. These resistors are effectively ignored since they do not impact the overall behavior of the circuit.
Know more about Resistors here:
https://brainly.com/question/30672175
#SPJ11
1. If a motor generates a sound pressure of 4.3 Pa, calculate the sound pressure level in decibels.
2. A worker is exposed to noise levels of 80 dBA for 60 minutes, 84 dBA for 120 minutes and a background level of 70 dBA for the remainder of their 8 hour shift. Calculate their 8 hour noise exposure.
3. Define the term ‘primary aerosol’. List three examples of a primary aerosol.
The sound pressure level in decibels is 58 dB
We know that Sound Pressure Level (SPL) is the ratio of the sound pressure to the reference pressure, multiplied by 20. The formula for calculating SPL is given below:
SPL = 20 log10 (P/P0)
Here, P = 4.3 Pa and P0 = 20 x 10^-6 Pa (reference pressure)
Therefore, SPL = 20 log10 (4.3/(20 x 10^-6))
= 20 log10 (215000)= 20 x 5.332
= 106.64 dB
≈ 58 dB2.
The worker's 8-hour noise exposure is 81.1 dBA
We know that the noise exposure level can be calculated using the following formula:
Noise Exposure (L)= (T1/L1) + (T2/L2) + (T3/L3)
Where,T1 = duration of exposure at level L1T2 = duration of exposure at level L2T3 = duration of exposure at level L3L1, L2, L3 = noise levelsW
e are given that T1 = 60 min, L1 = 80 dBA,
T2 = 120 min, L2 = 84 dBA, T3 = 8 hours - (60 min + 120 min)
= 6 hours = 360 minutes,
L3 = 70 dBA
Therefore,
Noise Exposure (L)= (60/80) + (120/84) + (360/70)
= 0.75 + 1.43 + 5.14= 7.32
Total noise exposure = 7.32
Therefore, the worker's 8-hour noise exposure is 81.1 dBA.3.
Primary aerosols are those aerosols which are emitted directly from the source without undergoing any chemical or physical change.
List of three examples of a primary aerosol are: Smoke
Dust
Salt spray
learn more about aerosols here
https://brainly.com/question/28853452
#SPJ11
Q4 Find the torque of the armature of a motor if it turns (N = 200 r/s )armature current = 100 Amper and the resistance of the armature = 0.5 ohms and back E.M.F. = 120 volts 1- Torgue = 40 N.m 2- Torque = 9.54 N.m O 3-Torque = 78 N.m O
The torque of the armature of a motor is 9.54 N.m.
Armature current Ia = 100 A
Resistance of the armature Ra = 0.5 Ω
Back emf Eb = 120 V
Speed N = 200 r/s
We know that,The torque T of the armature of a motor is given by,
T = Kφ Ia
Where, K is a constantφ is flux in webersIa is the armature current
The constant K is given as
K = P / 2πA
Where, P is the number of poles
A is the number of parallel paths
We know that, back emf, Eb = Kφ N
Therefore, φ = Eb / K N
Thus, the torque T of the armature of a motor is given as,T = (P φ Ia) / 2πA
Putting the given values in the above equation,
Torque T = (P Eb Ia) / 2πAN
= 200 r/s
Therefore, the speed N in rad/s = 2πN
= 2π × 200
= 1256.64 rad/s
Let's calculate the torque using the above formula.
Torque T = (P Eb Ia) / 2πA
Number of poles, P = 2
For parallel paths, A = 1
Back emf, Eb = 120 V
Armature current Ia = 100 A
Thus, T = (2 × 120 × 100) / (2 × 3.14 × 1 × 1256.64)
= 9.55 N.m
Therefore, the torque of the armature of a motor is 9.54 N.m.
Learn more about torque -
brainly.com/question/30338159
#SPJ11
A resistor having a resistance of 50 ohms is connected in series with an inductor having a reactance of 70 ohms. This series connection in then connected in parallel to a capacitor of unknown capacitance to create resonance in the circuit. If the source voltage produces 120 V, find the power dissipated in the circuit.
The power dissipated in the circuit is 163.3 W.
Given data Resistance of the resistor = 50 ohms
Reactance of the inductor = 70 ohms
Applied voltage = 120 V
Capacitance of capacitor = ?
Formula used
Power in an AC circuit = V²/R
= VI = V²/Z where
Z = impedance of the circuit The impedance of a series circuit is the sum of the resistance and reactance.
Z = R + jX where
j = √-1The impedance of the parallel circuit will be as follows Z
p = (ZL⁻¹ + ZR⁻¹ + ZC⁻¹)⁻¹The reactance of the capacitor will be -Xc because it has an inverse relationship with the inductor
Xc = 1/2πfC,
f = frequency
C = capacitance
Here, f = frequency of the source voltage
Now, let's solve the problemStep 1Find the impedance of the series circuit
Z = R + jX
Z = 50 + j70 ohms
Z = √50² + 70² ohms
Z = 86.6 ohms
Step 2
Find the impedance of the parallel circuit
Zp = (ZL⁻¹ + ZR⁻¹ + ZC⁻¹)⁻¹
Zp = [ (j70)⁻¹ + (50)⁻¹ + (-jXc)⁻¹ ]⁻¹
Zp = [ -j/70 + 1/50 - j/2πfC ]⁻¹
Zp = [ 1/(70² + 50²) - j(1/70 - 1/2πfC) ]⁻¹For resonance to occur,
Zp = R
Zp = ZRSo,86.6
ohms = 50 ohms + X86.6 - 50
= X X = 36.6 ohms
Step 3
Find the capacitance of the capacitor Xc = 1/2πfC36.6
= 1 / (2πfC)C
= 1 / (2πfXc)C
= 1 / (2π × 50 × 36.6) farad C
= 9.01 × 10⁻⁵ farad C
= 0.0901 microfarad
Step 4
Find the power dissipated in the circuit
Power = V²/Zp Power
= 120² / 86.6Power
= 163.3 watts
To know more about power visit:-
https://brainly.com/question/29575208
#SPJ11
A 1.50 V battery supplies 0.303 W of power to a small flashlight for 21.7 min. (a) How much charge does it move? How is charge related to the electric potential energy and potential? C (b) How many electrons must move to carry this charge? What is the charge carried by one electron?
Answer: a) 262.26 C charge does it moves through system.
b) Charge (Q) is related to electric potential energy (U) and potential (V) through the equation: U = QV
c) charge carried by one electron is e = 1.60 x 10^(-19) C.
(a) To calculate the amount of charge moved, we can use the equation: Power = Voltage x Current. Rearranging this equation, we can solve for the current (I):
I = Power / Voltage. Plugging in the given values,
we have: I = 0.303 W / 1.50 V = 0.202 A.
To find the charge (Q) moved, we can use the equation:
Q = I x t,
where I is the current and t is the time. Plugging in the values, we have: Q = 0.202 A x 21.7 min x 60 s/min
= 262.26 C.
Charge (Q) is related to electric potential energy (U) and potential (V) through the equation: U = QV. Electric potential energy is the amount of energy stored in a charge, and potential is the amount of electric potential energy per unit charge.
(b) To find the number of electrons that must move to carry this charge, we can use the equation: Q = n x e, where Q is the charge, n is the number of electrons, and e is the charge carried by one electron. Rearranging this equation, we have: n = Q / e.
Plugging in the values, we have: n = 262.26 C / 1.60 x 10^(-19) C = 1.64 x 10^21 electrons.
(c) The charge carried by one electron is e = 1.60 x 10^(-19) C.
To learn more about electric potential energy (U) and Charge:
https://brainly.com/question/26978411
#SPJ11
Two alarm sirens are emitting a loud note: at points between the two sirens the sound is very loud, but at other points it is much fainter. what wave phenomena described
The wave phenomena described in this scenario is known as interference.
Interference occurs when two or more waves interact with each other, resulting in the reinforcement or cancellation of the waves at certain points in space.
In this case, the two alarm sirens are emitting sound waves that are overlapping and interfering with each other. When the waves from the sirens are in phase, meaning their peaks and troughs align, constructive interference occurs. Constructive interference leads to the amplification of the sound waves, resulting in a louder sound at points between the two sirens.
On the other hand, when the waves from the sirens are out of phase, meaning their peaks and troughs are misaligned, destructive interference occurs. Destructive interference leads to the cancellation of the sound waves, resulting in a fainter sound at points where the waves interfere destructively.
The loud and faint regions of sound between the two sirens are a result of the constructive and destructive interference of the sound waves emitted by the sirens, respectively.
For more questions on sound waves, click on:
https://brainly.com/question/16093793
#SPJ8
How far does it take a car to stop if it has an initial speed of 28.0 m/s slows down at a rate of 3.80 m/s^2??
It takes a car to stop if it has an initial speed of 28.0 m/s slows down at a rate of 3.80 m/s^2 approximately 103.16 meters for the car to stop.
To find the distance it takes for a car to stop, we can use the equations of motion. In this case, the car is decelerating, so we can use the following equation:
v^2 = u^2 + 2as
Where:
v = final velocity (0 m/s, since the car stops)
u = initial velocity (28.0 m/s)
a = acceleration (deceleration in this case, -3.80 m/s^2)
s = distance
Plugging in the values, we get:
0^2 = (28.0 m/s)^2 + 2(-3.80 m/s^2)s
Simplifying the equation, we have:
0 = 784 m^2/s^2 - 7.6 m/s^2s
Rearranging the equation to solve for s, we get:
7.6 m/s^2s = 784 m^2/s^2
s = 784 m^2/s^2 / 7.6 m/s^2
s ≈ 103.16 m
To learn more about car
https://brainly.com/question/29110645
#SPJ11
Balance the following equations.
NO + O2 → NO2
KClO3 → KCl + O2
NH4Cl + Ca(OH)2 → CaCl2 + NH3 + H2O
NaNO3 + H2SO4 → Na2SO4 + HNO3
PbS + H2O2 → PbSO4 + H2O Al2(SO4)3 + BaCl2 → AlCl3 + BaSO4
Balanced equations:
2NO + [tex]O_2[/tex] → 2[tex]NO_2[/tex]2[tex]KClO_3[/tex] → 2KCl + 3[tex]O_2[/tex]2[tex]NH_4Cl[/tex] + [tex]Ca(OH)_2[/tex] →[tex]CaCl_2 + 2NH_3 + 2H_2O[/tex]2NaNO3 + [tex]H_2SO_4[/tex] → [tex]Na_2SO_4 + 2HNO_3[/tex][tex]3PbS + 4H_2O_2[/tex]→ [tex]3PbSO_4 + 4H_2O[/tex][tex]Al_2(SO_4)_3 + 3BaCl_2[/tex]→ 2Balancing chemical equations is essential to ensure that the law of conservation of mass is upheld. In the given equations, the number of atoms on both sides of the arrow must be equal. Here's how each equation is balanced:
2NO + O2 → 2NO2
By adding a coefficient of 2 in front of NO and NO2, we balance the equation by having an equal number of nitrogen and oxygen atoms on both sides.
2KClO3 → 2KCl + 3O2
To balance the equation, we place a coefficient of 2 in front of KClO3, 2 in front of KCl, and 3 in front of O2. This ensures that the number of potassium, chlorine, and oxygen atoms is equal on both sides.
2NH4Cl + Ca(OH)2 → CaCl2 + 2NH3 + 2H2O
By placing a coefficient of 2 in front of NH4Cl and NH3, and 2 in front of H2O, we balance the equation. This ensures that the number of nitrogen, hydrogen, and chlorine atoms is equal on both sides.
2NaNO3 + H2SO4 → Na2SO4 + 2HNO3
The equation is balanced by putting a coefficient of 2 in front of NaNO3 and HNO3, ensuring that the number of sodium, nitrogen, and oxygen atoms is equal on both sides.
3PbS + 4H2O2 → 3PbSO4 + 4H2O
By adding a coefficient of 3 in front of PbS and PbSO4, and 4 in front of H2O2 and H2O, the equation is balanced. This ensures that the number of lead, sulfur, hydrogen, and oxygen atoms is equal on both sides.
Al2(SO4)3 + 3BaCl2 → 2AlCl3 + 3BaSO4
By placing a coefficient of 2 in front of AlCl3, and 3 in front of Al2(SO4)3, BaCl2, and BaSO4, the equation is balanced. This ensures that the number of aluminum, sulfur, chlorine, and barium atoms is equal on both sides.
Learn more about Balanced equations
brainly.com/question/31242898
#SPJ11
Gallium Antimonide (GaSb) has a bandgap of 0.75 eV, an effective electron mass of m = 0.042 me and an effective hole mass of m= 0.4 me. For a sample of GaSb at the temperature of 300 K:
a) What is the modified Fermi energy?
b) What is the effective density of states for the holes in the valence band (Ny)?
c) What is the concentration of holes in the valence band (nn)?
d) Calculate if a photon with a wavelength of 1550 nm will be absorbed by an GaSb photodiode. Explain your result.
a) The modified Fermi energy at 300 K for GaSb is approximately 0.7592 eV, b) The effective density of states for holes in the valence band (Ny) is approximately 1.61 x 10^18 cm^-3, c) The concentration of holes in the valence band (nn) is approximately 2.43 x 10^16 cm^-3 and d) A photon with a wavelength of 1550 nm will not be absorbed by a GaSb photodiode since its energy (0.8008 eV) is lower than the bandgap energy (0.75 eV) of GaSb.
a) The modified Fermi energy (E_f) can be calculated using the equation:
E_f = E_g + (3/4)kT * ln(m_h/m_e)
where E_g is the bandgap energy, k is the Boltzmann constant (8.617 x 10^-5 eV/K), T is the temperature in Kelvin, and m_h and m_e are the effective mass of holes and electrons, respectively.
Substituting the given values:
E_g = 0.75 eV
m_h = 0.4 me (effective hole mass)
m_e = 0.042 me (effective electron mass)
T = 300 K
E_f = 0.75 eV + (3/4) * (8.617 x 10^-5 eV/K) * 300 K * ln(0.4/0.042)
Calculating E_f:
E_f ≈ 0.75 eV + 0.0092 eV ≈ 0.7592 eV
Therefore, the modified Fermi energy for GaSb at 300 K is approximately 0.7592 eV.
b) The effective density of states for the holes in the valence band (N_y) can be calculated using the equation:
N_y = 2 * (2π * m_h * k * T / h^2)^(3/2)
where m_h is the effective hole mass, k is the Boltzmann constant, T is the temperature in Kelvin, and h is the Planck's constant (4.136 x 10^-15 eV·s).
Substituting the given values:
m_h = 0.4 me
k = 8.617 x 10^-5 eV/K
T = 300 K
N_y = 2 * (2π * 0.4 * 8.617 x 10^-5 * 300 / (4.136 x 10^-15))^1.5
Calculating N_y:
N_y ≈ 1.61 x 10^18 cm^-3
Therefore, the effective density of states for the holes in the valence band (N_y) is approximately 1.61 x 10^18 cm^-3.
c) The concentration of holes in the valence band (n_n) can be calculated using the equation:
n_n = N_y * e^(-E_f / (k * T))
where N_y is the effective density of states for the holes, E_f is the modified Fermi energy, k is the Boltzmann constant, and T is the temperature in Kelvin.
Substituting the given values:
N_y = 1.61 x 10^18 cm^-3
E_f = 0.7592 eV
k = 8.617 x 10^-5 eV/K
T = 300 K
n_n = 1.61 x 10^18 * e^(-0.7592 / (8.617 x 10^-5 * 300))
Calculating n_n:
n_n ≈ 2.43 x 10^16 cm^-3
Therefore, the concentration of holes in the valence band (n_n) is approximately 2.43 x 10^16 cm^-3.
d) To determine if a photon with a wavelength of 1550 nm will be absorbed by a GaSb photodiode, we can calculate the energy of the photon using the equation:
E = hc/λ
where E is the energy of the photon, h is the Planck's constant, c is the speed of light, and λ is the wavelength.
Learn more about Fermi energy from the given link:
https://brainly.com/question/32064779
#SPJ11
A six pulse controlled rectifier is connected to a three phase, 440 V, 50 Hz supply and a dc generator. The internal resistance of the generator is 10 ohms and all of the six switches are controlled at firing angle, a 30". Evaluate:
i. The average load voltage.
ii. The maximum line current.
iii. The average load current, lo(avg).
iv. The peak inverse voltage, PIV.
V. The ripple frequency.
i. The average load voltage ≈ 248.8 V ii. The maximum line current ≈ 37.3 A iii. The average load current (Iload(avg)) ≈ 6.71 A iv. The peak inverse voltage (PIV) ≈ 880 V v. The ripple frequency (fr) = 75 Hz
To evaluate the given parameters for the six-pulse controlled rectifier system, we need to use the appropriate formulas and calculations. Here are the step-by-step calculations: Given:
Three-phase supply voltage (Vm) = 440 V
Frequency (f) = 50 Hz
Internal resistance of the generator (Rg) = 10 Ω
Firing angle (α) = 30°
i. The average load voltage can be calculated using the formula:
Vload(avg) = Vm/π * (1 - cos(α))
Substituting the given values:
Vload(avg) = 440/π * (1 - cos(30°))
Vload(avg) ≈ 248.8 V
ii. The maximum line current can be calculated using the formula:
Imax = √(2) * Vm / (π * Rg)
Substituting the given values:
Imax = √(2) * 440 / (π * 10)
Imax ≈ 37.3 A
iii. The average load current (Iload(avg)) can be calculated using the formula:
Iload(avg) = Imax / (2π) * (1 + cos(α))
Substituting the given values:
Iload(avg) = 37.3 / (2π) * (1 + cos(30°))
Iload(avg) ≈ 6.71 A
iv. The peak inverse voltage (PIV) can be calculated using the formula:
PIV = Vm / (2 * sin(α))
Substituting the given values:
PIV = 440 / (2 * sin(30°))
PIV ≈ 880 V
v. The ripple frequency (fr) can be calculated using the formula:
fr = (3 * f) / (2)
Substituting the given value of f:
fr = (3 * 50) / (2)
fr = 75 Hz
To learn more about, Current, click here, https://brainly.com/question/9682654
#SPJ11
The speed of a 20Hp, 300V, 2500rpm separately excited de motor is energized from a 208V, 60Hz, 3-phase source through 3 phase full converter. The field current is set to the maximum value. The de motor parameters are as under; ra-0.50, Km 0.8 V-s/rad, La-10mH. Rated armature current-210A. No-load armature current 10% of rated current. Armature current is continuous and ripple free. Calculate: Delay angle of armature converter if the motor supplies rated power at the rated speed.
The delay angle of the armature converter if the motor supplies rated power at the rated speed is 2.2 degrees.
In order to solve the problem, it is important to understand that the power output of a motor is given by: Pout = V x I x power factor x efficiency Where V is the supply voltage to the motor, I is the current flowing through the motor, power factor is the ratio of real power to apparent power, and efficiency is the ratio of mechanical output power to electrical input power. Now, the given motor parameters are as follows: Power rating = 20 HP Voltage rating = 300 V Speed rating
= 2500 rpm Armature resistance
= 0.5 Ohm Back emf constant
= 0.8 V-s/rad Armature inductance
= 10 mH Rated armature current
= 210 A No-load armature current
= 10% of rated current Armature current is continuous and ripple free.
Using these parameters, we can calculate the armature current under rated conditions: Power rating = 20 HP
= 14.92 kWI
= Pout / (V x power factor x efficiency) Efficiency can be assumed to be 0.9 for this type of motor, and power factor can be assumed to be 0.8. Thus, I = 14.92 / (300 x 0.8 x 0.9)
= 69.5 A Therefore, the armature current under rated conditions is 69.5 A. The delay angle of the armature converter is given by: sin(delay angle) = [tex](V - Eb) / (sqrt(2) x Eb x ra x I)[/tex] where V is the supply voltage, Eb is the back emf of the motor, ra is the armature resistance, and I is the armature current. Under rated conditions, the motor is supplying 20 HP at 2500 rpm, so we know that: Pout = 20 HP
= 14.92 kWEb
= Km x omega
= 0.8 x 2500 x 2pi / 60
= 209.4 V Substituting these values, we get:
[tex]sin(delay angle) = (300 - 209.4) / (sqrt(2) x 209.4 x 0.5 x 69.5)[/tex]
= 0.0383 Therefore, the delay angle of the armature converter is:
delay angle = arcsin(0.0383)
= 2.2 degrees.
To know more about speed visit:-
https://brainly.com/question/28224010
#SPJ11
A 4.1-kg object is moving horizontally along a straight line that goes through points A and
B as shown in the figure below. There is a constant force parallel to the x-y plane is given
by F =3.7 N i −5.0 N j . Find the work done on the object by this force when it moves
from A to B, if the distance between the two points is 50 m.
The work done on an object is given by the formula W = F * d * cosθ, where W is the work done, F is the force applied, d is the distance traveled, and θ is the angle between the force vector and the displacement vector. In this case, the force F = 3.7 N i - 5.0 N j is given. To find the work done, we need to find the distance traveled and the angle between the force and displacement vectors.
Given that the object moves from point A to point B with a distance of 50 m, we can use the distance formula:
d = √((x2-x1)^2 + (y2-y1)^2). From the figure, it seems that the x-coordinate changes from 0 to 50 m, while the y-coordinate remains constant. So, the displacement vector is d = 50 m i.
To find the angle between the force vector and the displacement vector, we can use the dot product formula F · d = |F| |d| cosθ. Since the force vector F is given as 3.7 N i - 5.0 N j and the displacement vector d is given as 50 m i, we have F · d = (3.7 N i - 5.0 N j) · (50 m i) = 3.7 N * 50 m * cosθ.
Now, we can solve for cosθ. Rearranging the equation, we have cosθ = (F · d) / (|F| |d|) = ((3.7 N * 50 m) / (sqrt((3.7 N)^2 + (-5.0 N)^2) * 50 m) = 0.833.
Plugging in the values into the work formula, we have W = (3.7 N i - 5.0 N j) * (50 m i) * 0.833 = 185 N*m.
Therefore, the work done on the object by this force when it moves from A to B is 185 N*m.
Learn more about the work done: https://brainly.com/question/25573309
#SPJ11
a)"Synchronous motors are inherently not self-starting". Explain
this statement.
b) Discuss the starting of synchronous motors by using the
Variable Frequency Method.
c) List some of the benefits
a)Synchronous motors are not self-starting because they require a rotating magnetic field. A synchronous motor consists of a rotor and a stator. The rotor is usually a permanent magnet, while the stator contains windings that generate a magnetic field.
b)Variable Frequency Method of Starting Synchronous Motors: By varying the frequency of the applied voltage, the Variable Frequency Method can start a synchronous motor. To begin, the stator windings are energized with a low-frequency AC voltage.
c)Some of the benefits of using synchronous motors include their high efficiency, high torque, and low power factor. Synchronous motors are also capable of operating at high speeds and are highly efficient in applications where power requirements are high and speed regulation is critical. Additionally, they can be used in applications where a precise and stable speed is required, such as in the manufacturing of electronics.
To know more about Synchronous visit:
https://brainly.com/question/27189278
#SPJ11
What is the maximum reverse repetitive voltage rating of the diode in the circuit given above.
In the circuit given above, the diode's maximum reverse repetitive voltage rating is calculated as follows:The circuit given above consists of a resistor (R), a diode (D), and a capacitor (C) connected in series. We want to find out the maximum reverse repetitive voltage rating of the diode.
Therefore, the first step is to examine the diode in the circuit given above. As the diode is an electronic component that only allows current to flow through it in one direction, we will investigate it further.To be more specific, the diode's maximum reverse voltage rating refers to the maximum voltage that can be applied across it in the opposite direction. As a result, this voltage rating is critical in ensuring that the diode is not damaged by a reverse voltage that exceeds this value.
In general, diodes have a maximum reverse voltage rating in the range of 50 to 1000 volts, depending on the type of diode. To calculate the maximum reverse voltage rating for a diode in a circuit, we must first identify the type of diode used, its part number, and its datasheet.However, as the type of diode used in the circuit is not given, it is impossible to determine its exact maximum reverse repetitive voltage rating. Therefore, we cannot calculate the diode's maximum reverse repetitive voltage rating in the circuit provided.
To know more about circuit visit :
https://brainly.com/question/12608516
#SPJ11
Quito, Ecuador is located at the equator (0o latitude). On which day(s) of the year does Quito experience the most daylight hours?
Group of answer choices
A. Autumn/Spring Equinox
B. Summer Solstice
C. Winter Solstice
2.
Victorville, CA is located at 34.53o north latitude. On which day of the year does Victorville experience the most daylight hours?
Group of answer choices
A. Winter Solstice
B. Summer Solstice
C. Autumn/Spring Equinox
3.
On which day(s) of the year is the sun directly over the equator?
Group of answer choices (Can choose more than one answer)
A. Spring Equinox
B. Autumn Equinox
C. Winter Solstice
D. Summer Solstice
4.
Indicate the latitude of each prominent geographic reference line for the indicated term (Choose one of Arctic Circle, Equator, Ring of Fire, Antarctic Circle, Tropic of Capricorn, Tropic of Aquarius, Prime Meridian, Tropic of Scorpio, or Tropic of Cancer for the terms below)
a) 0 Degrees Latitude
b) 23.5 Degrees North Latitude
c) 23.5 Degrees South Latitude
d) 66.5 Degrees North Latitude
1) Quito experiences the most daylight hours during the Autumn/Spring Equinox. 2 ) Victorville experiences the most daylight hours on the Summer Solstice. 3) The sun is directly over the equator on both the Spring Equinox and Autumn Equinox. 4) The Equator is at 0 degrees latitude, the Tropic of Cancer is at 23.5 degrees North latitude, the Tropic of Capricorn is at 23.5 degrees South latitude, and the Arctic Circle is at 66.5 degrees North latitude.
1) Quito, Ecuador:
The city of Quito, located near the equator, experiences relatively consistent daylight hours throughout the year. Therefore, none of the given options (Autumn/Spring Equinox, Summer Solstice, Winter Solstice) stand out as having significantly more daylight hours than others. Quito's proximity to the equator means it receives fairly consistent daylight throughout the year.
2) Victorville, CA:
Victorville, located at 34.53° north latitude, experiences the most daylight hours on the Summer Solstice (Option B). The Summer Solstice, which occurs around June 21st in the Northern Hemisphere, marks the longest day of the year when the sun is at its highest point in the sky, resulting in more daylight hours.
3) The sun is directly over the equator on the following days:
Spring Equinox (Option A): Around March 20th, when the sun crosses the equator from the southern hemisphere to the northern hemisphere.
Autumn Equinox (Option B): Around September 22nd, when the sun crosses the equator from the northern hemisphere to the southern hemisphere.
4) Geographic reference lines for the indicated terms:
a) Equator: 0 degrees latitude.
b) Tropic of Cancer: 23.5 degrees North latitude.
c) Tropic of Capricorn: 23.5 degrees South latitude.
d) Arctic Circle: 66.5 degrees North latitude.
To know more about Autumn Equinox refer here
brainly.com/question/29105988
#SPJ11
2. Determine the change in length of steel rod having a length of 800mm and a diameter of 6mm. The rod is subjected to a force Pequal to 100KN. Young's Modulus is 200GPa 3. Compute normal strain of the rod in Problem 2.
To compute the normal strain of the steel rod, we can use the formula: strain = change in length / original length , the change in length of the steel rod is approximately 1415.4 meters.
The boat is able to float because the buoyant force acting upward on the boat is equal to the weight of the boat. This is due to the principle of buoyancy. The boat displaces an amount of water equal to its own weight, and as a result, the buoyant force upward balances the weight downward.
To know more about buoyant visit :
https://brainly.com/question/32138756
#SPJ11
A scientist working late at night in her low-temperature physics laboratory decides to have a cup of hot tea, but discovers the lab hot plate is broken. Not to be deterred, she puts about 8.00 oz of water, at 12.0°C, from the tap into a lab dewar (essentially a large thermos bottle) and begins shaking it up and down. With each shake the water is thrown up and falls back down a distance of 23.5 cm.
If she can complete 30 shakes per minute, how long will it take for the water to reach 81.1°C?
days
It will take approximately 65.3 days for the water to reach 81.1°C.
To determine the time it takes for the water to reach a certain temperature, we need to consider the heat transfer involved. The shaking motion of the water in the lab dewar provides mechanical energy, which is converted into thermal energy through friction. This leads to an increase in the water's temperature.
The heat transfer can be calculated using the equation:
Q = mcΔT,
where Q is the heat transferred, m is the mass of the water, c is the specific heat capacity of water, and ΔT is the change in temperature.
In this case, we have the initial temperature of 12.0°C and the final temperature of 81.1°C. Assuming the specific heat capacity of water is 4.184 J/g°C, we can calculate the heat transfer. The mass of the water is given as 8.00 oz, which is approximately 226.8 grams.
Using the formula, we can solve for Q:
Q = (226.8 g) * (4.184 J/g°C) * (81.1°C - 12.0°C) = 68,237.79 J
Now, to determine the time it takes for this heat transfer to occur, we need to consider the rate at which the scientist shakes the water. If she completes 30 shakes per minute, it means she completes 30 cycles of shaking per minute.
Assuming each shake corresponds to one cycle, we can calculate the time required for one cycle:
Time per cycle = 1 shake / 30 shakes per minute = 1/30 minutes
To convert this time to days, we divide by the number of minutes in a day (24 hours * 60 minutes):
Time per cycle = (1/30) / (24 * 60) days ≈ 0.0000463 days
Finally, we can determine the total time required for the water to reach 81.1°C by dividing the total heat transfer (Q) by the heat transfer per cycle:
Total time = Q / (Heat transfer per cycle) = 68,237.79 J / 0.0000463 days ≈ 65.3 days
Therefore, it will take approximately 65.3 days for the water to reach a temperature of 81.1°C through the shaking process.
Learn more about the water
brainly.com/question/28465561
#SPJ11
Required information A current source in a linear circuit has is = 25 cos( At+25) A. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
Find the frequency of the current, where A = 22.
The frequency of the current is Hz.
The frequency of the current is approximately 3.503 Hz. in this case, the frequency of the current is:frequency = ω / (2π) = 22 / (2π) ≈ 3.503 Hz (rounded to three decimal places).So, the frequency of the current is approximately 3.503 Hz.
To find the frequency of the current in the given linear circuit, we can use the formula: frequency = ω / (2π). Given that the current source is described as: is = 25 cos(At + 25).With A = 22, we can substitute the value into the equation:is = 25 cos(22t + 25).Comparing this equation to the standard form of a cosine function: is = A cos(ωt + φ). We can see that the coefficient of t in the argument of the cosine function is A, which represents the angular frequency (ω) in radians per unit time.Therefore, in this case, the frequency of the current is:frequency = ω / (2π) = 22 / (2π) ≈ 3.503 Hz (rounded to three decimal places).So, the frequency of the current is approximately 3.503 Hz.
To learn more about frequency:
https://brainly.com/question/29739263
#SPJ11
please help with answer on question 16 ??
Question 16 of 20: Select the best answer for the question. 16. What is the R-value of an air space? O A. Essentially zero O B..91 O C. 1 O D..0028 O Mark for review (Will be highlighted on the review
The R-value of an air space is essentially zero.
An air space is a space between two layers of material. The R-value of an air space is essentially zero. R-value measures the effectiveness of insulation in preventing heat flow.
R-value is the measure of a material's resistance to heat flow from warmer to cooler temperature across the material. The higher the R-value of the material, the greater the insulating effectiveness.
Learn more about R-value from :
https://brainly.com/question/33355911
#SPJ11
An inductor has a reluctance of 1.0X10⁶(H-⁴), the winding of the inductor has N=10. What is the inductance of the inductor?
10 mH
0.1 mH
1 mH
The inductance of an inductor can be determined using the formula L = (N^2) / R, where N represents the number of turns in the winding and R is the reluctance of the inductor. In this case, the given reluctance is 1.0x10^6 (H^-4) and the number of turns is N = 10.
Substituting these values into the formula, we get L = (10^2) / (1.0x10^6) = 100 / (1.0x10^6) = 0.1x10^-3 H.
So, the inductance of the inductor is 0.1 millihenries (mH).
Inductance is a measure of the ability of the inductor to store electrical energy in the form of a magnetic field when a current flows through it. It depends on factors such as the number of turns in the winding and the physical characteristics of the inductor, such as its geometry and magnetic permeability.
In this case, with a reluctance of 1.0x10^6 (H^-4) and 10 turns in the winding, the inductance is relatively small at 0.1 mH. Inductors with larger inductance values are often used in various applications, such as in power electronics, signal filtering, and energy storage systems.
To learn more about, Inductor, click here, https://brainly.com/question/31503384
#SPJ11
