Answer:
Final Temperature = 71 °C
Explanation:
In this case, the ideal gas equation is written as;
PV = mRT
Where;
P is pressure
V is volume
m is mass
R is gas constant
T is temperature
We will take the volume to be constant.
So, in the initial state, we have;
P1•V = m1•R•T1 - - - eq(1)
In the final state, we have;
P2•V = m2•R•T2 - - - - eq(2)
Combining eq (1) and eq(2),we have;
P1•m2•R•T2 = P2•m1•R•T1
Dividing both sides by R gives;
P1•m2•T2 = P2•m1•T1
Making T2 the subject gives;
T2 = (P2•m1•T1)/(P1•m2)
Now, we are given;
m1 = 2kg
m2 = ½*2 = 1kg
P1 = 4 atm
P2 = 2.2 atm
T1 = 40°C = 273 + 40 K = 313K
Plugging in this values into the T2 equation, we have;
T2 = (2.2 × 2 × 313)/(4 × 1)
T2 = 344 K
Converting to °C, we have;
T2 = 344 - 273 = 71 °C
For the RC circuit and the RL circuit, assume that the period of the source square wave is much larger than the time constant for each. Make a sketch of vR(t) as a function of t for each of the circuits?
Answer with Explanation:
Concepts and reason
The concept to solve this problem is that if a capacitor is connected in a RC circuit then it allows the flow of charge through circuit only till it gets fully charged. Once the capacitor is charged it will not allow any charge or current to flow.
Opposite is the case with inductor in the RL circuit. According to Faraday's law an inductor develops an emf to oppose the voltage applied but once the flux change stops then the inductor behaves just like a normal wire as if no inductor is there.
In attached figure, resistor is connected in series to the capacitor.
As we considered [tex]V_{C}[/tex] the voltage across the capacitor and [tex]V_{s}[/tex] the voltage across the source.
Voltage across a resistor In RC circuit.
[tex]V_{R}=V_S\left ( e^{-\frac{t}{RC}} \right )[/tex]
Voltage across a resistor In RL circuit.
[tex]V_{R}=V_S\left (1- e^{-\frac{Rt}{L}} \right )[/tex]
The sketch of [tex]\mathbf{v_R(t)}[/tex] as a function of t for each of the circuits can be seen in the diagram attached below.
For the Pre-Laboratory exercise, based on the assumption that the RC circuit has a capacitor and a sensing resistor while the RL circuit has a sensing resistor and an inductor.
The input voltage for both circuits is regarded as the square wave and if the square wave is much larger than the time constant for each.
Therefore, we can conclude that the below diagram shows an appropriate sketch of [tex]\mathbf{v_R(t)}[/tex] as a function of t for each of the circuits.
Learn more about RC circuits and RL circuits here:
https://brainly.com/question/15595203
Suppose the demand for air travel decreases (as illustrated in the graph below). A decrease in demand _____ the equilibrium price for air travel and _____ the equilibrium quantity for air travel. decreases, decreases increases, increases decreases, increases
Answer:
decreases, decreases
Explanation:
A decrease in the demand will create a fall in equilibrium prices and the quantity supplied will also decrease. As the equilibrium prices in the market are the price in which the quantity demanded equals to quantity supplied. If the demand for the air decreases then the quantity of the air travel will also decrease and thus when the supply and demand change so do the changes associated with the equilibrium prices.If you secure a refrigerator magnet about 2mmfrom the metallic surface of a refrigerator door and then move the magnet sideways, you can feel a resistive force, indicating the presence of eddy currents in the surface.
A)Estimate the magnetic field strength Bof the magnet to be 5 mTand assume the magnet is rectangular with dimensions 4 cmwide by 2 cmhigh, so its area A is 8 cm2. Now estimate the magnetic flux ΦB into the refrigerator door behind the magnet.
Express your answer with the appropriate units.
B)If you move the magnet sideways at a speed of 2 cm/s, what is a corresponding estimate of the time rate at which the magnetic flux through an area A fixed on the refrigerator is changing as the magnet passes over? Use this estimate to estimate the emf induced under the rectangle on the door's surface.
Express your answer with the appropriate units.
Answer:
(A) 4* 6 ^ ⁻6 T m² (B) 2 * 10 ^ ⁻6 v
Explanation:
Solution
Given that:
A refrigerator magnet about = 2 mm
The estimated magnetic field strength of the magnet is = 5 m T
The Area = 8 cm²
Now,
(A) The magnetic flux ΦB = BA
Thus,
ΦB = (5 * 10^⁻ 3) ( 4 * 10 ^⁻2) * ( 2 * 10^ ⁻2) Tm²
So,
ΦB = 4* 6 ^ ⁻6 T m²
(B)By applying Faraday's Law we have the following formula given below:
Ε = Bℓυ
Here,
ℓ = 2 cm the same as 2 * 10 ^⁻2 m
B = 5 m T = 5 * 10 ^ ⁻3 T
υ = 2 cm/s = 2 * 10 ^ ⁻2 m/s
Thus,
Ε = (5 * 10 ^ ⁻3 T) * (2 * 10 ^ ⁻2) (2 * 10 ^ ⁻2) v
E =2 * 10 ^ ⁻6 v
A) The magnetic flux ΦB into the refrigerator door behind the magnet :
4 * 6⁻⁶ Tm²B) The estimated emf induced under the rectangle on the door's surface ;
2 * 10⁻⁶ vGiven data :
magnetic field strength of magnet ( B ) = 5 mT
size of refrigerator magnet = 2 mm
Area of magnet ( A ) = 4 * 2 = 8 cm²
A) Determine the magnetic flux ΦBwhere ; ΦB = BA
ΦB = ( 5 * 10⁻³ ) * ( 4 * 10⁻² ) * ( 2 * 10⁻² ) Tm²
= 4 * 6⁻⁶ Tm²
B) Determine estimated emf inducedTo determine the estimated emf we will apply Faraday's law
Ε = Bℓυ ---- ( 2 )
where : B = 5 * 10⁻³ T, ℓ = 2 * 10⁻² m, υ = 2 * 10⁻² m/s
insert values into equation 2
E = ( 5 * 10⁻³ ) * ( 2 * 10⁻² ) * ( 2 * 10⁻² )
= 2 * 10⁻⁶ v
Hence we can conclude that The magnetic flux ΦB is 4 * 6⁻⁶ Tm² and The estimated emf induced is 2 * 10⁻⁶ v
Learn more about magnet flux : https://brainly.com/question/4721624
The “turning effect of a force” (T = F * r) is:
(a) determined as the product of force and the moment of inertia.
(b) generated by concentric forces.
(c) equivalent to the angular momentum.
(d) determined as a product of torque and moment arm.
(e) called “moment” or “torque”.
Answer:
b and e
Explanation:
r x F is the formula for torque.
The "turning effect" or torque happens when concentric forces rotate an object along said center.
a) False because T = Fr = Ia (a = angular acceleration)
b) True
c) False. L = Iw (w = angular velocity), which does not equal Ia
d) False. It is torque, not the product of torque and something else
e) True.
You drive in straight line at 20 m/s for 10 miles, then at 30m/s for an other 10 miles what is your average speed
Answer:
25 m/s
Explanation:
Data provided in the question
20 m/s for 10 minutes
And, the 30 m/s for another 10 minutes
Based on the above information, the average speed is
As we know that
[tex]Average\ speed = \frac{Total\ distance}{Total\ time}[/tex]
[tex]= \frac{20\times10\times60 + 30\times10\times60 }{20\times60}[/tex]
= 25 m/s
1 hour = 60 minutes
1 minute = 60 seconds
Hence, the average speed is 25 m/s
In the question, there are miles is given but instead of this we use the minutes as we have to find out the average speed and time should not be in miles it should be in minutes, hour or seconds
Therefore we considered the same
An experiment invilves three charges objects: A, B, and C. Object A repels object B and attracts onject C. object C ir repelled by ebonite charged with fur. What is the charge on the object?
Answer:
A and B is positive charge
C_negative
Explanation:
because when an ebonite is rubbed with fur produce negative charge due to law of electrostatic like charge repel and unlike attract
How can I show that the sphere of radius R performs a simple harmonic movement. how can i set its reference point and make the free body diagram.
I have the torque sum equation which is equal to the moment of inertia by angular acceleration
Explanation:
Draw a free body diagram of the pendulum (the combination of the sphere and the massless rod). There are three forces on the pendulum:
Weight force mg at the center of the sphere,
Reaction force in the x direction at the pivot,
Reaction force in the y direction at the pivot.
Sum the torques about the pivot O.
∑τ = I d²θ/dt²
mg (L sin θ) = I d²θ/dt²
For small θ, sin θ ≈ θ.
mg L θ = I d²θ/dt²
Since d²θ/dt² is directly proportional to θ, this fits the definition of simple harmonic motion.
If you wish, you can use parallel axis theorem to find the moment of inertia about O:
I = Icm + md²
I = ⅖ mr² + mL²
mg L θ = (⅖ mr² + mL²) d²θ/dt²
gL θ = (⅖ r² + L²) d²θ/dt²
A tank circuit consists of an inductor and a capacitor. Give a simple explanation for why the magnetic field in the induc- tor is strongest at the moment that the separated charge in the capacitor reaches zero.
Answer:
If you pull a permanent magnet rapidly away from a tank circuit, what is likely to happen in that circuit?
Charge will oscillate in the tank's capacitor and inductor.
Explanation:
Two workers are sliding 330 kg crate across the floor. One worker pushes forward on the crate with a force of 430 N while the other pulls in the same direction with a force of 330 N using a rope connected to the crate. Both forces are horizontal, and the crate slides with a constant speed. What is the crate's coefficient of kinetic friction on the floor?
Answer:
Coefficient of kinetic friction = 0.235
Explanation:
Given:
Mass of crate = 330 kg
1st force = 430 N
2nd force = 330 N
Find:
Coefficient of kinetic friction.
Computation:
We know that, velocity is constant.
So, acceleration (a) = 0
So, net force (f) = 430 N + 330 N
Net force (f) = 760 N
F = μmg
μ = f / mg [∵ g = 9.8]
μ = 760 / [330 × 9.8]
μ = 760 / [3,234]
μ = 0.235
Coefficient of kinetic friction = 0.235
Olaf is standing on a sheet of ice that covers the football stadium parking lot in Buffalo, New York; there is negligible friction between his feet and the ice. A friend throws Olaf a ball of mass 0.400 kg that is traveling horizontally at 11.3 m/s. Olaf's mass is 75.0 kg. (a) If Olaf catches the ball, with what speed v_f do Olaf and the ball move afterward
Answer:
v = 0.059 m/s
Explanation:
To find the final speed of Olaf and the ball you use the conservation momentum law. The momentum of Olaf and the ball before catches the ball is the same of the momentum of Olaf and the ball after. Then, you have:
[tex]mv_{1i}+Mv_{2i}=(m+M)v[/tex] (1)
m: mass of the ball = 0.400kg
M: mass of Olaf = 75.0 kg
v1i: initial velocity of the ball = 11.3m/s
v2i: initial velocity of Olaf = 0m/s
v: final velocity of Olaf and the ball
You solve the equation (1) for v and replace the values of all variables:
[tex]v=\frac{mv_{1i}}{m+M}=\frac{(0.400kg)(11.3m/s)}{0.400kg+75.0kg}=0.059\frac{m}{s}[/tex]
Hence, after Olaf catches the ball, the velocity of Olaf and the ball is 0.059m/s
To practice Problem-Solving Strategy 6.1: Circular motion A highway curve with radius R = 274 m is to be banked so that a car traveling v = 25.0 m/s will not skid sideways even in the absence of friction. At what angle should the curve be banked?
Answer:
The curve should be banked at an angle of 13 degrees.
Explanation:
We have,
Radius of a highway curve is 274 m
Speed of car on this curve is 25 m/s
Let [tex]\theta[/tex] is the banking angle. On a banked curve, the angle of safe diving is given by following expression.
[tex]\tan\theta=\dfrac{v^2}{Rg}[/tex]
g = 10 m/s²
Plugging all the values in above formula,
[tex]\tan\theta=\dfrac{(25)^2}{274\times 9.8}\\\\\theta=\tan^{-1}\left(\dfrac{(25)^{2}}{274\times9.8}\right)\\\\\theta=13^{\circ}[/tex]
So, the curve should be banked at an angle of 13 degrees.
A sample of silver (with work function Φ=4.52 eV ) is exposed to an ultraviolet light source (????=200 nm), which results in the ejection of photoelectrons. What changes will be observed if:
1. The silver is replaced with copper (Φ= 5.10 eV)?
a. more energetic photoelectrons (on average)
b. no photoelectrons are emitted more photoelectrons ejected
c. less energetic photoelectrons (on average)
d. fewer photoelectrons ejected
2. A second (identical) light source also shines on the metal?
a. fewer photoelectrons ejected
b. no photoelectrons are emitted more
c. energetic photoelectrons (on average)
d. less energetic photoelectrons (on average)
e. more photoelectrons ejected
3. The ultraviolet source is replaced with an X-ray source that emits the same number of photons per unit time as the original ultraviolet source?
a. no photoelectrons are emitted
b. less energetic photoelectrons (on average)
c. fewer photoelectrons ejected
d. more energetic photoelectrons (on average)
e. more photoelectrons ejected
Answer:
1. c
2. e
3. d
Explanation:
1.
From Einstein's Photoelectric Equation, we know that:
Energy given up by photon = Work Function + K.E of Electron
hc/λ = φ + K.E
where,
h = Plank's Constant = 6.626 x 10⁻³⁴ J.s
c = speed of light = 3 x 10⁸ m/s
λ = wavelength of light source = 200 nm = 2 x 10⁻⁷ m
φ = (5.1 eV)(1.6 x 10⁻¹⁹ J/eV) = 8.16 x 10⁻¹⁹ J
Therefore,
(6.626 x 10⁻³⁴ J.s)(3 x 10⁸ m/s)/(2 x 10⁻⁷ m) - 8.16 x 10⁻¹⁹ = K.E
K.E = (9.939 - 8.16) x 10⁻¹⁹ J
K.E = 1.778 x 10⁻¹⁹ J
The positive answer shows that electrons will be emitted. Since it is clear from the equation the the K.E of electron decreases with the increase in work function. Therefore:
c. less energetic photo-electrons (on average)
2.
The increase in light sources means an increase in the intensity of light. The no. of photons are increased, due to increase of intensity. Thus, more photons hit the metal and they eject greater no. of electrons. Therefore,
e. more photo-electrons ejected
3.
X-rays have smaller wavelength and greater energy than ultraviolet rays. Thus, the photons with greater energy will strike the metal and as a result, electrons with higher energy will be ejected.
d. more energetic photo-electrons (on average)
g Tether ball is a game children play in which a ball hangs from a rope attached to the top of a tall pole. The children hit the ball, causing it to swing around the pole. What is the total initial acceleration of a tether ball on a 2.0 m rope whose angular velocity changes from 13 rad/s to 7.0 rad/s in 15 s
Answer:
a = -0.8 m/s²
Here, negative sign indicates that the acceleration has opposite direction to the direction of motion.
Explanation:
First we find the angular acceleration of the ball from the following formula:
α = (ωf - ωi)/t
where,
α = angular acceleration = ?
ωf = final angular velocity = 7 rad/s
ωi = initial angular velocity = 13 rad/s
t = Time taken = 15 s
Therefore,
α = (7 rad/s - 13 rad/s)/15 s
α = - 0.4 rad/s
negative sign shows that acceleration is in opposite direction to the direction of motion.
Now, for the linear acceleration, we use the formula:
a = rα
where,
a = linear acceleration = ?
r = radius of circular path = length of rope = 2 m
therefore,
a = (2 m)(- 0.4 rad/s²)
a = -0.8 m/s²
Here, negative sign indicates that the acceleration has opposite direction to the direction of motion.
Why do bears activity increase as certain points during the day
Because they are well rested and have to work to get food in their system.
Use Hooke's Law to determine the work done by the variable force in the spring problem. Nine joules of work is required to stretch a spring 0.5 meter from its natural length. Find the work required to stretch the spring an additional 0.40 meter.
Answer:
29.16 J
Explanation:
From Hook's law,
W = 1/2(ke²)..................... Equation 1
Where W = work done, k = Spring constant, e = extension.
Given: W = 9 J, e = 0.5 m.
Substitute into equation 1
9 = 1/2(k×0.5²)
Solve for k
k = 18/0.5²
k = 72 N/m.
The work done required to stretch the spring by additional 0.4 m is
W = 1/2(72)(0.4+0.5)²
W = 36(0.9²)
W = 29.16 J.
The amount of friction divided by the weight of an object forms a unit less number called the
Answer:
Coefficient of friction.
Explanation:
The amount of friction divided by the weight of an object is equal to the coefficient of friction. It is a dimensional less number. It can be given by :
[tex]F=\mu N[/tex]
N is normal force.
[tex]\mu[/tex] = coefficient of friction
[tex]\mu=\dfrac{F}{N}[/tex]
4) (7 pts.) A water molecule is centered at the origin of a coordinate system with its dipole moment vector aligned with the x axis. The magnitude of a water molecule dipole is 6.16 × 10−30 C·m. What is the magnitude of the electric field at x = 3.00 × 10−9 m?
Answer:
[tex]E=3.69*10^{-11}\frac{V}{m}[/tex]
Explanation:
To solve this problem you use the following formula, for the calculation of the electric field along the axis of the dipole.
[tex]E=\frac{p}{2\pi \epsilon_ox^3}[/tex] (1)
p: dipole moment = 6.16*10^-30 Cm
x: distance to the center of mass of the dipole = 3.00*10^-9m
eo: dielectric permittivity of vacuum = 8.85*10^-12 C^2/Nm^2
You replace the values of the variables in the equation (1):
[tex]E=\frac{6.16*10^{-30}Cm}{2\pi(8.85*10^{-12}C^2/Nm^2)(3.00*10^{-9}m)^3}\\\\E=3.69*10^{-11}\frac{V}{m}[/tex]
A 328-kg car moving at 19.1 m/s in the x direction hits from behind a second car moving at 13.0 m/s in the same direction. If the second car has a mass of 790 kg and a speed of 15.1 m/s right after the collision, what is the velocity of the first car after this sudden collision
Answer:
14.04 m/s
Explanation:
To find the velocity of the first car after the collision, we can use the equation of conservation of momentum:
m1v1 + m2v2 = m1'v1' + m2'v2'
We have the following data:
m1 = m1' = 328,
m2 = m2' = 790,
v1 = 19.1,
v2 = 13,
v2' = 15.1.
Using this data, we can find v1' (final velocity of the first car):
328 * 19.1 + 790 * 13 = 328 * v1' + 790 * 15.1
16534.8 = 328 * v1' + 11929
328 * v1' = 4605.8
v1' = 14.04 m/s
What type of device forms images by changing the speed at which light travels?
Answer:
A lens
Explanation:
A lens forms images when light passes Through it bending the rays of in the process.A phenomena called refraction and the speed of light changes in the process because it enters a medium since it's wavelength is reduced.
The type of device that forms images by changing the speed at which light travels is the lens.
What is refraction through the lens?
A lens bends a light beam at an aimed perspective and converges or diffuses bundles of rays by taking benefit of refraction taking vicinity while the mild travels from air into glass or plastic. For that purpose, the aspect geometry of a lens has a spherical parent, which can be kind of divided into sorts.
A lens bends a mild beam at an aimed perspective and converges or diffuses bundles of rays through taking gain of refraction taking area whilst the mild travels from air into glass or plastic. For that motive, the facet geometry of a lens has a round parent, which may be kind of divided into sorts.
Learn more about the speed of light here:-https://brainly.com/question/104425
#SPJ2
A note on a piano vibrates 262 times per second . What is the period of the wave ?
please help
Complete the first and second sentences, choosing the correct answer from the given ones.
1. A temperature of 100 K corresponds on a Celsius scale to 100 ° C / 0 ° C / 173 ° C / –173 ° C.
2. At 50 ° C, it corresponds to a Kelvin scale of 150 K / 323 K / 273 K / 223 K.
1) 100 ° C
2) 323 K
hope it helps youuuuuu
When solving vector addition problems you can use either the graphical
method or the
Answer :the resultant of two vectors can be found using either the parallelogram method or the triangle method. don't know if this was helpful ?
Explanation:
Answer:
Analytical method.
An engine draws energy from a hot reservoir with a temperature of 1250 K and exhausts energy into a cold reservoir with a temperature of 322 K. Over the course of one hour, the engine absorbs 1.37 x 105 J from the hot reservoir and exhausts 7.4 x 104 J into the cold reservoir.
1) What is the power output of this engine?
2) What is the maximum (Carnot) efficiency of a heat engine running between these two reservoirs?
3) What is the actual efficiency of this engine?
Answer:
The power output of this engine is [tex]P = 17.5 W[/tex]
The the maximum (Carnot) efficiency is [tex]\eta_c = 0.7424[/tex]
The actual efficiency of this engine is [tex]\eta _a = 0.46[/tex]
Explanation:
From the question we are told that
The temperature of the hot reservoir is [tex]T_h = 1250 \ K[/tex]
The temperature of the cold reservoir is [tex]T_c = 322 \ K[/tex]
The energy absorbed from the hot reservoir is [tex]E_h = 1.37 *10^{5} \ J[/tex]
The energy exhausts into cold reservoir is [tex]E_c = 7.4 *10^{4} J[/tex]
The power output is mathematically represented as
[tex]P = \frac{W}{t}[/tex]
Where t is the time taken which we will assume to be 1 hour = 3600 s
W is the workdone which is mathematically represented as
[tex]W = E_h -E_c[/tex]
substituting values
[tex]W = 63000 J[/tex]
So
[tex]P = \frac{63000}{3600}[/tex]
[tex]P = 17.5 W[/tex]
The Carnot efficiency is mathematically represented as
[tex]\eta_c = 1 - \frac{T_c}{T_h}[/tex]
[tex]\eta_c = 1 - \frac{322}{1250}[/tex]
[tex]\eta_c = 0.7424[/tex]
The actual efficiency is mathematically represented as
[tex]\eta _a = \frac{W}{E_h}[/tex]
substituting values
[tex]\eta _a = \frac{63000}{1.37*10^{5}}[/tex]
[tex]\eta _a = 0.46[/tex]
Mr. Patel is photocopying lab sheets for his first period class. A particle of toner carrying a charge of 4.0 * 10^9 C in the copying machine experiences an electric field of 1.2 * 10^6 N/C as it’s pulled toward the paper. What is the electric force acting on the toner particle?
Answer:
4.8 × 10^15 N
Explanation:
Electric Field is defined as Force per unit Charge.
This is expressed mathematically as;
E= F/Q
Where E- Electric Field
F- Force
Q- charge
From the expression above by change of subject of formula for F, we have;
F=E×Q
= 1.2 * 10^6 ×4.0 * 10^9
= 4.8 × 10^15 N
Q) Considering the value of ideal gas constant in S.I. unit, find the volume of 35g O2 at 27°C and 72
cm Hg pressure. Later, if we keep this pressure constant, the r.m.s velocity of this oxygen molecules
become double at a certain temperature. Calculate the value of this temperature.
Answer:
V = 0.0283 m³ = 28300 cm³
T₂ = 1200 K
Explanation:
The volume of the gas can be determined by using General Gas Equation:
PV = nRT
where,
P = Pressure of Gas = (72 cm of Hg)(1333.2239 Pa/cm of Hg) = 95992.12 Pa
V = Volume of Gas = ?
n = no. of moles = mass/molar mass = (35 g)/(32 g/mol) = 1.09 mol
R = General Gas Constant = 8.314 J/ mol.k
T = Temperature of Gas = 27°C + 273 = 300 k
Therefore,
(95992.12 Pa)(V) = (1.09 mol)(8.314 J/mol.k)(300 k)
V = 2718.678 J/95992.12 Pa
V = 0.0283 m³ = 28300 cm³
The Kinetic Energy of gas molecule is given as:
K.E = (3/2)(KT)
Also,
K.E = (1/2)(mv²)
Comparing both equations, we get:
(3/2)(KT) = (1/2)(mv²)
v² = 3KT/m
v = √(3KT/m)
where,
v = r.m.s velocity
K = Boltzamn Constant
T = Absolute Temperature
m = mass of gas molecule
At T₁ = 300 K, v = v₁
v₁ = √(3K*300/m)
v₁ = √(900 K/m)
Now, for v₂ = 2v₁ (double r.m.s velocity), T₂ = ?
v₂ = 2v₁ = √(3KT₂/m)
using value of v₁:
2√(900 K/m) = √(3KT₂/m)
4(900) = 3 T₂
T₂ = 1200 K
John pushes Hector on a plastic toboggan.The free-body diagram is shown. A free body diagram with 4 force vectors. The first vector is pointing downward, labeled F Subscript g Baseline = negative 490 N. The second vector is pointing right, labeled F Subscript t Baseline = 735 N. The third vector is pointing upward, labeled F Subscript N Baseline = 490 N. The fourth vector is pointing left, labeled F Subscript f Baseline = negative 245 N. The up and down vectors are the same length. The right vector is longer than the left vector. What is the net force acting on Hector and the toboggan?
Answer:
490 N
Explanation:
is the correct answer
If the up and down vectors are the same length. The right vector is longer than the left vector, then the net force acting on Hector and the toboggan would be 490 Newtons.
What is Newton's second law?Newton's Second Law states that The resultant force acting on an object is proportional to the rate of change of momentum.
As given in the problem John pushes Hector on a plastic toboggan .The free-body diagram is shown. A free body diagram with 4 force vectors. The first vector is pointing downward, labeled F Subscript g Baseline = negative 490 N. The second vector is pointing right, labeled F Subscript t Baseline = 735 N. The third vector is pointing upward, labeled F Subscript N Baseline = 490 N. The fourth vector is pointing left, labeled F Subscript f Baseline = negative 245 N.
The net force acting on the vertical direction = 490-490
=0
The net force acting on the horizontal direction = 735 -245
=490 Newtons
Thus, the net force acting on Hector and the toboggan would be 490 Newtons.
Learn more about Newton's second law from here, refer to the link ;
brainly.com/question/13447525
#SPJ5
A particle moving along the x-axis has a position given by m, where t is measured in s. What is the magnitude of the acceleration of the particle at the instant when its velocity is zero
Question:
A particle moving along the x-axis has a position given by x=(24t - 2.0t³)m, where t is measured in s. What is the magnitude of the acceleration of the particle at the instant when its velocity is zero
Answer:
24 m/s
Explanation:
Given:
x=(24t - 2.0t³)m
First find velocity function v(t):
v(t) = ẋ(t) = 24 - 2*3t²
v(t) = ẋ(t) = 24 - 6t²
Find the acceleration function a(t):
a(t) = Ẍ(t) = V(t) = -6*2t
a(t) = Ẍ(t) = V(t) = -12t
At acceleration = 0, take time as T in velocity function.
0 =v(T) = 24 - 6T²
Solve for T
[tex] T = \sqrt{\frac{-24}{6}} = \sqrt{-4} = -2 [/tex]
Substitute -2 for t in acceleration function:
a(t) = a(T) = a(-2) = -12(-2) = 24 m/s
Acceleration = 24m/s
What is the velocity of a car that travels 556km northwest in 3.2 hours
Answer:
173.75 km/hr in the NW direction.
Explanation:
Velocity is the time rate of change in displacement of a body. Mathematically:
v = d / t
where d = displacement
t = time
Therefore, the velocity of the car is:
v = 556 / 3.2 = 173.75 km/hr
The velocity of the car is 173.75 km/hr in the NW direction.
The velocity of a car will be "173.75 km/hr".
Displacement and Velocity,The velocity of something like a car moving northward on something like a prominent motorway as well as the velocity of something like a rocket launching towards spacecraft both might be determined or monitored.
Displacement, d = 556 km
Time, t = 3.2 hours
We know the relation,
→ Velocity = [tex]\frac{Displacement}{Time}[/tex]
or,
→ V = [tex]\frac{d}{t}[/tex]
By substituting the values, we get
= [tex]\frac{556}{3.2}[/tex]
= [tex]173.75[/tex] km/hr
Thus the response above is right.
Find out more information about velocity here:
https://brainly.com/question/6504879
The NASA spacecraft Deep Space I was shut down on December 18, 2001, following a three-year journey to the asteroid Braille and the comet Borrelly. This spacecraft used a solar-powered ion engine to produce 0.064 ounces of thrust (force) by stripping electrons from neon atoms and accelerating the resulting ions to 70,000 mi/h. The thrust was only as much as the weight of a couple sheets of paper, but the engine operated continuously for 16,000 hours. As a result, the speed of the spacecraft increased by 7900 mi/h. What was the mass of Deep Space I?
Answer:
The mass will be "8.86 lb".
Explanation:
The given values are:
Force
= 70,000 mi/h
Speed
= 7900 mi/h
On applying the Law of momentum, we get
⇒ [tex]V_{1}m_{1}=V_{2}m_{2}[/tex]
On putting the estimated values, we get
⇒ [tex]70000 = 7900\times mass \ of \ deepspace \ 1[/tex]
⇒ [tex]mass \ of \ deepspace \ 1 = \frac{70000}{7900}[/tex]
⇒ [tex]=8.86 \ lb[/tex]
510 g squirrel with a surface area of 935 cm2 falls from a 4.8-m tree to the ground. Estimate its terminal velocity. (Use the drag coefficient for a horizontal skydiver. Assume that the squirrel can be approximated as a rectanglar prism with cross-sectional area of width 11.6 cm and length 23.2 cm. Note, the squirrel may not reach terminal velocity by the time it hits the gr
Answer:
The terminal velocity is [tex]v_t =17.5 \ m/s[/tex]
Explanation:
From the question we are told that
The mass of the squirrel is [tex]m_s = 50\ g = \frac{50}{1000} = 0.05 \ kg[/tex]
The surface area is [tex]A_s = 935 cm^2 = \frac{935}{10000} = 0.0935 \ m^2[/tex]
The height of fall is h =4.8 m
The length of the prism is [tex]l = 23.2 = 0.232 \ m[/tex]
The width of the prism is [tex]w = 11.6 = 0.116 \ m[/tex]
The terminal velocity is mathematically represented as
[tex]v_t = \sqrt{\frac{2 * m_s * g }{\dho_s * C * A } }[/tex]
Where [tex]\rho[/tex] is the density of a rectangular prism with a constant values of [tex]\rho = 1.21 \ kg/m^3[/tex]
[tex]C[/tex] is the drag coefficient for a horizontal skydiver with a value = 1
A is the area of the prism the squirrel is assumed to be which is mathematically represented as
[tex]A = 0.116 * 0.232[/tex]
[tex]A = 0.026912 \ m^2[/tex]
substituting values
[tex]v_t = \sqrt{\frac{2 * 0.510 * 9.8 }{1.21 * 1 * 0.026912 } }[/tex]
[tex]v_t =17.5 \ m/s[/tex]
