A sheet of aluminium foil is held in front of a radioactive source. TWO types of radiation are detected on the other side. State which type of radiation will NOT be detected. * giving out BRAINLIEST

The modulus of elasticity is 117.5 KN/[tex]cm^{2}[/tex].

How can we find the modulus of elasticity?

Modulus of elasticity is commonly known as Young's Modulus, which is denoted as E. To find modulus of elasticity we know that,

E = σ / ∈-----(1)

where σ is denoted as stress,

and   ∈ is denoted as strain.

σ  = F/A ------(2)

where F is denoted as load,

and A is denoted as area.

 ∈= ΔL/L ------(3)

where ΔL is denoted as the resulting change in length,

and L is denoted as the original length.

Given that,

L = 3.6m = 360cm

d = 2.6cm

F = 61 KN

ΔL = 3.52mm = 0.352cm

E = ?

By substituting the values in (2) & (3) we get,

  ⇒  σ  = F/A

  A =  π/4 [tex]d^{2}[/tex] = (π/4)×([tex]2.6^{2}[/tex]) = 5.3092 [tex]cm^{2}[/tex]

  σ = 61/(5.309) = 11.5

   ⇒ ∈ = ΔL / L

  = (0.352) / 360  

E = σ / ∈

  = [tex]\frac{(61)(360)}{(5.309)(0.352)}[/tex] = 1177 KN/[tex]cm^{2}[/tex]

Therefore the modulus of elasticity is 1177 KN/[tex]cm^{2}[/tex]

To know more about the modulus of elasticity, visit the given link:

https://brainly.com/question/18993970

#SPJ4

Light with a frequency of 7.30 x 10¹⁴ that lies in the violet region of the visible spectrum has a wavelength of 412nm.

The wavelength of light can be defined as the distance between two successive crests, or troughs of a wave of light, usually denoted by the Greek letter, lambda (λ).

Wavelength is directly proportional to frequency. This means that the shorter the wavelength, the higher the frequency. To find the wavelength of any electromagnetic wave if we are given the frequency, we use the following formular:

                    λ = [tex]\frac{v}{f}[/tex]

Where;

The velocity or speed of light is the same for all electromagnetic waves which is 3 x 10⁸m/s. We are already given the frequency in the question as 7.30 x 10¹⁴hz. Putting these values into the formular:

                      λ = 3 x 10⁸/7.30 x 10¹⁴

                      λ = 4.12 x 10⁻⁷m

However, to convert the wavelength from meter to nanometer, we would have to multiply the answer by 10⁹. Therefore;

                  λ = 4.12 x 10⁻⁷m x 10⁹ = 412nm

Learn more about wavelength here:

https://brainly.com/question/13961990

#SPJ4

The net change in the internal energy is 40joules.

Given here, the force (F) = 800N acting over a distance of (D) = 0.05m(1cm = 0.01m)

First, we calculate work done by the formula,

Work done = Force × displacement

Work done = 800× 0.05

= 40joules.

Now, we calculate internal energy the first law of thermodynamics.

Internal Enegy (dE) =dQ + W

dE= 0+40

dE = 40joules.

Thus, internal energy was found to be +40joules.

Adiabatic process is a kind of thermodynamic process that takes place without the thermodynamic system or its surroundings exchanging heat or matter, in simple words it is defined as the system where no heat loss Or gained by the system.

An adiabatic process only transfers energy to the environment as work, as contrast to an isothermal process. The adiabatic process is a fundamental idea in thermodynamics and supports the law behind the first law of thermodynamics.

To learn more about adiabatic process, refer this link.

https://brainly.com/question/14926413

#SPJ4

yes, it appears that births occur on the days of the week with frequencies that are about the same.

It is obvious from the relative frequency table that almost no day has a relative frequency value that is double that of any other day. We may thus draw the conclusion that these births happen almost equally frequently on each day of the week. Please keep in mind that the relative frequency statistics vary slightly over the course of seven days.

To know more about frequency visit:

https://brainly.com/question/14316711

#SPJ4

An electric pencil sharpener is a small motorized appliance for sharpening or refreshing the points on lead pencils.

An electric pencil sharpener is a small motorized equipment for polishing or fresh the factors on lead pencils. Within the hollow, a small electric powered motor turns a blade meeting at high velocity. The blades shave wooden and lead from the pencil's cease, bringing it to some extent.

The old-fashioned pencil sharpeners which are established to the wall and cranked through a manage are an instance of a compound system that is composed  simple machines: the wheel and axle and a wedge.

You could sharpen colored pencils in an electric sharpener, however make certain to be very mild with your pencils and often easy your sharpener to put off any wax increase. If performed improperly, sharpening your colored pencils in an electric sharpener can harm each your pencils and your sharpener.

Learn more about electric pencil here:- https://brainly.com/question/1921424

#SPJ9

The critical angle for this interface is closest is 45.6 degrees.

The refractive index is the velocity or the speed of the light through which the ratio is calculated by comparing that velocity to be present in the vacuum by its velocity in any specified medium which can be water or air and this medium is also called secondary medium and this medium should be greater density than the former one. The refractive index is represented by the letter 'n' and the value of the refractive index for air is 1.0003 and in the case of liquid the refractive index values can range from 1.0010 to 1.0060 and the formula for the refractive index calculation is n = c/v where n is the refractive index, c is the velocity or speed of light and v is the phase velocity of light that means when light is some other phase like liquid or air or refractive index can also be defined as the bending of the light when the light passes from one medium to other of different densities.

Given -

The Refractive index of crown glass is = 1.52

The Refractive index of water is = 1.33

The angle of incidence = 40°

To calculate the angle of refraction in water -

Using Snell's law

[tex]n_1 sin \theta i = n_2 sin \theta r[/tex]

[tex]n_1 / n_2 = sin \theta r/sin \theta i[/tex]

Where,

[tex]n_1[/tex] = Refractive index of crown glass

[tex]n_2[/tex] = Refractive index of water

[tex]\theta[/tex] i = incidence angle

Putting the value we will get

1.52 /1.33 = sin [tex]\theta[/tex]r / 40

sin [tex]\theta[/tex]r = sin 40 [tex]\times[/tex] 1.52 / 1.33

sin [tex]\theta[/tex] r = 0.715

So, theta r will be

[tex]sin^{-1}[/tex] ( 0.715 ) = 45.6 degrees.

Hence the correct answer is 45.6 degrees of the critical angle.

To know more about Refractive index this click at https://brainly.in/question/18404669

#SPJ4

The length of one sheet of the standard sheet of printer paper in terms of centimeters is 27.94

As we are given that,  the standard sheet of printer  paper is 8.5  inches wide and 11 inches long,The calculation for this problem is just two-step,

So, we know that 1 inch is equal to  2.54 centimeters.

So, the width of the paper in terms of centimeters will be 8.5 X 2.54 =21.54 cm and the length of the paper in terms of centimeters will be   11 x 2.54 =  27.94 cm

to know more about conversion refer to the link https://brainly.com/question/18828615?referrer=searchResults.

#SPJ4

Answer:

16fl = 90 kacl because 8 fl double = 16 fl so 45 kcal = 90 kcal (double )

When an object is spinning around its center, as you move out from the center and the radius increases: the angular velocity decreases

The fact that the angular velocity of an object that is spinning around its center decreases as the object moves away from the center is due to the fact that as it moves away from the center the radius increases and because the relationship between radius and angular velocity is inversely proportional, as the radius increases the angular velocity decreases.

When an object is in uniform circular motion, the angle described by the radius in each unit of time is known as angular velocity. It is measured in units of (rad/s) (revolutions/s).

Learn more about angular velocity at brainly.com/question/20432894

#SPJ4

Answer:

a

Explanation:

vector is size and direction

hope this works :)

The value in centimeters is [tex]1.44 \times 10^{-8}[/tex] cm.

Dimensional analysis is a method for changing a measurement's unit of measurement. A single unit of measurement can be multiplied by a number of fractions that, although expressed in different units, are essentially the same measurement.

A unit of measurement is a specific magnitude of a quantity that is adopted by law or convention and used as a standard for measuring other quantities of the same kind. Another amount of that type may be expressed as a multiple of the measuring unit.

Radius of gold =144pm

[tex]=144pm\times 1m/10^{12}pm[/tex]

[tex]=144 \times 10^{12} m[/tex]

[tex]=1.44 \times 10^{-10} m[/tex]

[tex]= 1.44 \times 10^{-8} cm.[/tex]

To learn more about the radius of an atom refer to the link:

https://brainly.com/question/14544878

#SPJ4

The acceleration's direction is always mirrored by the net force.

Given that a sailboat is moving across the water at a constant speed, we must determine the direction of the fourth point on the board.

As a result, we can claim that the investigation of bowties judo has been granted that bowties are moving at a constant speed.

In light of Newton's second law, the net force exerted on the boat is thus negligible since it equals mass times acceleration, and since acceleration is zero.

As a result of the velocity limitations, the solution is equal to this rate of change in velocity.

Execution is 0 for now. So that we can understand their responsibilities. There was no fourth act aboard the boat.

Learn more about velocity here

https://brainly.com/question/25749514

#SPJ4

A chunk of metal gets burned through using an industrial laser. The RMS value of the electric field will be 2.25 mT.

Root Mean Square is the name for this phrase. The square root of the mean square of the voltage signal's instantaneous values is known as an RMS voltage. The quadratic mean is another name for the RMS. In terms of an integral of the squares of the instantaneous values over a cycle, RMS voltage can also be expressed as a continuously fluctuating voltage.

Average intensity of the light is S=1.21×[tex]10^{9}[/tex] w/m²

The RMS value will be :

S=ε₀c[tex](E_r_m_s)^{2}[/tex]

[tex](E_r_m_s)^{2}[/tex]=S/ε₀

=√(1.21×[tex]10^{9}[/tex]) / (8.85×[tex]10^{-12}[/tex])(3.0×[tex]10^{8}[/tex] m/s)

=6.75×[tex]10^{5}[/tex] N/c

B=[tex](E_r_m_s)[/tex]/c

=(6.75×[tex]10^{5}[/tex] N/c) / (2.25×[tex]10^{-3}[/tex] m/s)

=2.25×[tex]10^{-3}[/tex] T

=2.25 mT

Hence, the RMS value of the electric Field is 2.25 mT.

To get more information about RMS value :

https://brainly.com/question/12906838

#SPJ4

The modulus of elasticity of normal weight concrete is 9400 ksi.

The modulus of elasticity is the measure of the stiffness of a substance. It measures the resistance of an object to being deformed.

Generally, the objects with higher values of modulus of elasticity are stronger and therefore preferred to be used as a building material for construction purposes.

The relation between the compressive strength(C) of a substance and its modulus of elasticity(E) is given by the following formula;

E = 4700√C ksi

We are given that the compressive strength of normal weight concrete is 4 ksi,

Therefore, E = 4700 √4

E = 9400 ksi

Thus, the modulus of elasticity of normal weight concrete is 9400 ksi.

To know more about "modulus of elasticity", refer to the following link:

https://brainly.com/question/22108303?referrer=searchResults

#SPJ4

The crest of an ocean wave moves a distance of given time is 2 m/s.

To know the speed of the wave,

Use the formula,

speed = distance / time

Given,

distance = 20 m

time = 10s

s = ?

Putting values,

s = d / t

s = 20 / 10

s = 2 m/s

Although some individuals may believe that average speed and average velocity are simply two different names for the same quantity, average speed depends on both distance and displacement. The average speed will be greater than the average velocity if an object changes direction while traveling.

To know more about average speed :

https://brainly.com/question/12322912

#SPJ9

The minimum horizontal velocity must the cliff divers leave the top of the cliff if they miss the rock would be 2.86 m/s.

It is the rate of change of an object's position with regard to time and a frame of reference. Although it may appear sophisticated, velocity is just the act of moving quickly in one direction. Since it is a vector quantity, the definition of velocity requires both magnitude (speed) and direction.

SI unit of velocity is m/s.

Velocity= displacement/ time

There are different types of velocity :

According to the question :

h=[tex]V_o[/tex]×t +0.5(g)(t²)

=0+0.5(9.8)(t²)

⇒4.9 t²=33.7

⇒ t²=6.89

so, t=2.62 seconds

d=v×t=7.51 m

⇒2.62 V=7.51 m

V=7.51/2.62

V=2.86 m/s

Hence, the minimum velocity must be 2.86 m/s.

To get more information about horizontal velocity :

https://brainly.com/question/18084516

#SPJ1

The probability of five tails turning up in seven flips is 16.4%

In reality, if one concentrates on one possible outcome, referring to it as success and all other outcomes as a failure, one can say that an experiment with three or more possible outcomes is a binomial experiment.

When researching the decay of a kaon in elementary particle physics, for instance ( K particle).

Binomial random variables are produced by binomial experiments, and they will be the subject of our next couple of lessons.

A very particular kind of experiment is a binomial experiment. Four requirements must be satisfied for an experiment to be considered a binomial experiment:

A specific number of trials must be conducted. Because the number of rolls (trials) is not fixed, the experiment cannot simply consist of rolling a die until you get a 2.

Every trial must stand alone from the others.

A rule like "If you flip a coin and get heads, flip it twice more, and if you get tails, flip it three times more" is not acceptable.

There must be a "success" and a "failure" in every trial. These may vary depending on the trial.

To learn more about Binomial Experiments, refer

to https://brainly.com/question/26117248

#SPJ4

a) The shoppers who walked from the car to the door in 20 minutes walked for 1200 seconds.

b) The shoppers' walking speed in meters per second is 0.67m/s.

A) In the question, we are already given how long it took for the shoppers to walk from their car to the entrance of the shopping mall, although it's in minutes. We are told that it took them 20 minutes to walk from their car to the entrance. In order to know how long they were walking in seconds, we would have to multiply by 60. This is because there are 60 seconds in one minute. Hence, to find the number of seconds in 20 minutes, we multiply 20 minutes by 60 seconds, thus;

                     20 minutes × 60 seconds = 1200 seconds.

B) Now that we know how long the shoppers were walking in seconds, we can use it to get their walking speed. To find the speed of any moving object, we divide the distance the object travelled by the time taken for the object to cross that distance in seconds. In the question, we are told that the shoppers parked their car 800 meters away from the entrance. This means that the distance they walked to get to the entrance is also 800 meters. Thus to find their walking speed;

                               Speed = distance ÷ time

                               Speed = 800 meters ÷ 1200 seconds

                              Speed = 0.67 m/s.

Therefore, the shoppers walked for 1200 seconds at 0.67m/s.

Learn more about speed and time here:

https://brainly.com/question/20113406

#SPJ4

She has travelled a total of 1300 metres away from the starting point if she travels 1200 metres north and 500 metres due east.

We can determine the total distance travelled by a body with position function s (t) when it moves along a coordinate line without changing direction from t = a to t = b.

We must incorporate the body’s speed |v (t)| to determine the overall distance travelled if the body changes direction once or more during the journey.

Metre

The metre [m] is the SI unit of length and displacement.

Let A is the initial position of the hiker.

After walking 1200 metres north reached point B, after walking 500 metres east due to B. She reached point C.

Total distance travelled = 1200 + 500

= 1700

The distance from strating point is AC from triangle ABC

AC^2 = AB^2 + BC^2

AC^2 =(1200)^2 + (500)^2

= 1440000 + 250000

= 1690000

AC^2 = 1690000

AC= [tex]\sqrt{1690000}[/tex]

⇒ AC = 1300 m

To know more about displacement visit:

https://brainly.com/question/11934397

#SPJ4

The final magnification will be 100X.

The light compound microscope contains two lenses to assist viewing of small objects. The two lenses are ocular lens and objective lens. Ocular lens is in the eyepiece and magnifies the image. Objective lens is near the sample and magnifies the object. Ocular lens is always 10X. Now, if we use objective lens of 10X, the magnification will be calculated by multiplication. So, the final magnification of the microscope will be 100X.

Compound microscope is commonly used to view the samples in magnification ranging from 40X to 1000X. There are variety of microscopes that provide detailed and highly magnified images, for instance, fluorescence microscope, digital microscope, electron microscope etc.

Learn more about microscope -

https://brainly.com/question/12864254

https://brainly.com/question/15744335

#SPJ4

By using Hooke's Law, the isentropic bulk modulus is 1,360,563.38 Pa.

We need to know about Hooke's Law to solve this problem. Hooke's Law describes the force applied to spring (elastic materials) will proportional to spring constant and displacement under the elastic condition. It can be described as

F = k . x

where F is force, k is spring constant and x is displacement.

The bulk modulus can be measured by stress and strain which

B = σ/ε

B = (F/A) / (ΔV/V)

where σ is stress, ε is strain, A is surface area, ΔV is change in volume and L is initial volume.

From the question above, we know that

σ = 276 kN/m² = 276 kPa = 276000 Pa

V = 0.35 m³

ΔV = 0.071 m³

By substituting the given parameters, we get

B = σ/ε

B = 276000 / (ΔV/V)

B = 276000 / (0.071/0.35)

B = 1,360,563.38 Pa

Find more on Hooke's Law at: https://brainly.com/question/12253978

#SPJ4

Because Newton could not provide comprehensive proof, his Binomial Theorem is not a "theorem" in the sense of Euclid or Archimedes. Nonetheless, his knowledge and intuition served him well enough for him to construct a useful formula.

Furthermore, his intrinsic conviction in the persistence of patterns led him to believe that the formula that correctly generated coefficients for binomial powers such as (a+b)^2 or (a+b)^3 should also work for powers such as (a+b)^1/2 or (a+b)^−3.

Although Newton did not establish this finding, we do know how he came to it. Newton's explanation is offered in a pair of letters dated 1676 and delivered to Leibniz by Henry Oldenburg of the Royal Society. In it, he describes how he came to his conclusion in a roundabout way.

He was looking at the areas under the curves y=(1−x2)n2  from 0 to x for n=0, 1, 2, 3,.... These are simple to compute for even n. Newton was able to guess the solution for odd values of n by studying patterns and interpolating. Then he recognized that expressing (1−x2)n2 as an infinite series would provide the same results.

Newton wrote :

(P+PQ)mn=Pmn+mnAQ+m−n2nBQ+m−2n3nCQ+…

where P+PQ is the binomial to be considered; mn is the power to which the binomial will be raised "whether that power is integral or (so to speak) fractional, positive or negative"; and A,B,C,... indicate the term immediately preceding it in the expansion.

When compared to the present version, this may appear strange. When you remove the Pmn word from the right side and cancel, you get the more known form:

(1+Q)mn=1+mnQ+(m/n)(m/n−1)2Q2+(m/n)(m/n−1)(m/n−2)2×3Q3+(m/n)(m/n−1)(m/n−2)(m/n−3)2×3×4Q4+…

Thus, in Newton's notation,

A=Pmn

B=mnAQ=mnPmnQ

C=(m−n)2nBQ=(m−n)m(2n)nPmnQ2=(m/n)(m/n−1)2PmnQ^2

To know more about "Binomial Theorem"

Refer this link:

brainly.com/question/13550824

#SPJ4

Answer:

yes it's the right answer...............

The mass of a 100.0 cm3 chunk of this steel is  810 grams.

What is Density?

A substance's density is defined as its mass per unit of volume. Density is most frequently represented by the symbol, however Latin letter D may also be used. Density is mathematically defined as mass divided by volume.

Density = Mass/ volume

Mass = density x volume

Mass at 100 cm3 = density x volume x 100 cm3

Mass at 100 cm3 = 8.1 g/cm x 100 cm 3

Mass at 100 cm3 = 810 grams

To learn more about Density  click on the link below:

https://brainly.com/question/18939565

#SPJ4

An impartial explanation of water at a certain temperature has a concentration of oh- of 5.3 x 10^-7.

The kw at this temp = 2081 × [tex]10^{-13}[/tex]

It can also defined as solution is one which has an equal concentration of [tex]H^+[/tex] and [tex]OH^-[/tex] ions in the solution.

Hence,

Kw = 2081 × [tex]10^{-13}[/tex]

concentration  of   [tex]OH^{-}[/tex]= 5.3 ×  [tex]10^{-7}[/tex] M

For neutral solution  [tex]OH^{-}[/tex] = (H3O+) = 5.3 ×  [tex]10^{-7}[/tex] M

From relation from Kw,  [tex]OH^{-}[/tex], and H3O+

Kw = [ [tex]OH^{-}[/tex]][H3O+] =  5.3 ×  [tex]10^{-7}[/tex] M × 5.3 ×  [tex]10^{-7}[/tex] M

Kw = 2.81 ×  10_13

To learn more about neutral solution, visit;

https://brainly.com/question/21444245

#SPJ4

The metal sample with a density of 1.56 g/l and a volume of 250ml , has a mass of: b) 0.39 grams

The density formula and the procedure we will use is:

ρ = m/v

Where:

Information about the problem:

Converting the volume unit from mL to L, we have:

250 mL * (1 L / 1000 mL) = 0.25 L

Applying the density formula and clearing the mass (m), we get:

m = ρ * v

m = 1.56 g/L* 0.25 L

m = 0.39 g

Although part of your question is missing, you might be referring to these group of answer choices: a)6.24 grams; b)0.39 grams; c)0.16grams; d) 0.59 grams

It is a physical quantity that expresses the ratio of the body mass to the bit occupies.

Learn more about density in: brainly.com/question/1354972

#SPJ4

Ka, Kb, and Ksp are all different types of equilibrium constants. The difference between these three is that Ka is the acid dissociation constant, Kb is the base dissociation constant and Ksp is the solubility product constant.

The relationship between a reaction's products and reactants with regard to a certain unit is expressed by the equilibrium constant, K. When an acid and its conjugate base are in equilibrium, Kb serves as the equilibrium constant, Ka is the acid equilibrium constant. Simply put, pKa is the -log of Ka.

Similar to this, Kb is the base dissociation constant and pKb is its -log. The moles per liter (mol/L) unit of measurement is commonly used to express the acid and base dissociation constants. The amounts of species present when ions are in equilibrium with undissolved salt are described by the solubility product (Ksp).

Learn more about equilibrium constant here:

https://brainly.com/question/10038290

#SPJ4

The symbol of the element oxygen is O, its proton number is 8, its atomic mass is 16, its neutron number is 8 and finally; oxygen belong to period 2 of the periodic table.

That being said, every atom of an element has within its nucleus; proton and neutrons of which electrons revolve round it. In the case of oxygen, it has

Oxygen, because it belongs to group vi and period 2 of the periodic table has a valence electrons of 6 electrons. This means that oxygen is a non metals.

An element can simply be defined as a chemical substance which which cannot be split into simpler units by ordinary means

An atom is the smallest part of element which can take part in a chemical reaction. Oxygen is a diatomic element which means that it exist in its molecules consisting of two atoms.

Below are the names of some elements:

So therefore, the symbol of the element oxygen is O, its proton number is 8, its atomic mass is 16, its neutron number is 8 and finally; oxygen belong to period 2 of the periodic table.

Learn more about chemical elements:

https://brainly.com/question/7289437

#SPJ1

The magnitude of the average acceleration of the car is  5.69 m/s², the distance (in m) the car travels in the first 7.20 s is 147.5 m an the speed of the car (in m/s) 10.0 s after it begins its motion will be 56 m/s.

Average acceleration is defined as the average rate of change of velocity per unit time. Mathematically -

a[avg] = Δv/Δt

Given in the question a sports car will accelerate from rest to a speed of 41.0 m/s in 7.20 s. From this, we can write -

Initial velocity [u] = 0 m/s

Final velocity [v] = 41 m/s

time taken (Δt) = 7.2 s

Part A → Average acceleration

The average acceleration of car can be calculated as follows -

a = Δv/Δt = (v - u)/t = (41 - 0) / 7.2 = 5.69 m/s²

Part B → Distance covered

The distance travelled by the car in first 7.20 seconds will be -

S = ut + 1/2 at²

S = 1/2 at²

S = 0.5 x 5.69 x 7.2 x 7.2

S = 147.5 m

Part C → Speed after 10 seconds

Using the first equation of motion -

v = u + at

v = at

v = 5.6 x 10

v = 56 m/s

Therefore, the magnitude of the average acceleration of the car is  5.69 m/s², the distance (in m) the car travels in the first 7.20 s is 147.5 m an the speed of the car (in m/s) 10.0 s after it begins its motion will be 56 m/s.

To solve more questions on Kinematics, visit the link below-

https://brainly.com/question/13139004

#SPJ1