A short shunt machine has armature, shunt, and series field resistances of 0.05, 0 and 400, 22, and 0.80 respectively. When driven as a generator at 952 rpm, the machine delivers 32 kW at 400 V. The calculations are done as follows;Generator Developed Power:
We know that the generated power formula is given by, P = (ΦNZ/60)A volts Substitute the given values and simplify 32 × 103 = Φ × 400 × (952/60)Φ = (32 × 106)/(400 × 15.87)Φ = 133.85m Wb The developed power when running as a generator is 32 kW.Generator Efficiency:The efficiency of a generator is given by the output power divided by the input power. This means,Generator efficiency = Output power/Input power Substitute the given values and simplify Generator efficiency = 32,000/33,460.8 × 100
Generator efficiency = 95.4%Developed Power When Running As A Motor Taking 32 kW from 400 V:The formula for the developed power of a motor is given by,P = ΦNZ/60 × A where A is the number of conductors per slot Substitute the given values and simplify;32 × 103 = Φ × 400 × (952/60) × (2/3)Φ = (32 × 106)/(400 × 15.87 × 0.63)Φ = 267.69 mWbP = ΦNZ/60 × A Substitute the given values P = (267.69 × 400 × 952)/(60 × 2/3)P = 678.5 kW FULL Load Motor Torque
To know more about resistances visit:
https://brainly.com/question/29427458
#SPJ11
ans
asap pls!!
Consider having two Full-Am signals: an AM signal with high modulation index and another AM signal with low modulation index. Which of them has higher power efficiency?
Modulation index is the ratio of the maximum frequency deviation of the carrier signal to the maximum frequency deviation of the modulating signal. It determines the extent to which the amplitude or frequency of a carrier wave varies as a function of the signal being modulated.
Therefore, an AM signal with a low modulation index has higher power efficiency than an AM signal with a high modulation index. When a carrier wave is modulated with low-level audio signals, the modulation index is low, and the output signal is more efficient as a result.
As a result, the AM signal with a low modulation index has a higher power efficiency than the AM signal with a high modulation index. This is due to the fact that the signal with the lower modulation index has more power in its carrier and less in the sidebands.
Learn more about Modulation at https://brainly.com/question/33354815
#SPJ11
The values of m and C are respectively 2 and 3. The vector X=[10,20,40,60,70,80,90]. Write an ALP using 8086 to compute. the vector Y for corresponding values of vector X and store the resulting vector starting from the memory location 8000H.
The given question is based on the topic of 8086 assembly language programming where a program is to be written to compute the corresponding values of the vector Y based on the given values of m and C for the given vector X and store the resulting vector starting from the memory location 8000H.
The values of m and C are given as m = 2 and C = 3, respectively. And the given vector X is X=[10,20,40,60,70,80,90].For the computation of the vector Y, the given formula is to be used, which is Y= m*X+C, where m=2, C=3 and X is the given vector.The ALP (Assembly Language Program) to compute the values of the vector Y is as follows:MOV AX, 8000H; move the address of memory location 8000H to AXMOV CX, 07H; move the counter value 07H to CXLEA SI, X; load the offset address of the X vectorMOV BH, 02H; move the value of m (i.e. 2) to BHMOV BL, 03H; move the value of C (i.e. 3) to BLBACK:MOV AX, [SI]; move the first element of the X vector to AXMUL BH; multiply the value of AX with BHADD AX, BX; add the value of AX with BXMOV [8000H],
AX; store the computed value of Y in the memory location pointed by 8000HINC SI; increment the pointer to point to the next element of the vector XDEC CX; decrement the value of counter by 1JNZ BACK; jump to the BACK if the value of counter is not zero at presentHere, in the above code, LEA stands for Load Effective Address, MOV stands for Move, MUL stands for Multiply, ADD stands for Addition, INC stands for Increment, DEC stands for Decrement, and JNZ stands for Jump if Not Zero.The above ALP will compute the corresponding values of the vector Y based on the given values of m and C for the given vector X and store the resulting vector starting from the memory location 8000H. The resulting vector will be stored in the memory locations starting from 8000H, and the next 6 memory locations (i.e. 8001H to 8006H) will be occupied by the computed vector Y.
Learn more about memory location here,
https://brainly.com/question/14447346
#SPJ11
electrical wiring and Installation course
Q1
Q2
An apartment block with 30 consumers( each having 10KVA of installed power ) has a total demand apparent power S in KVA Select one: 200 132 150 180
The installed apparent power \( S \) in VA is used
The total demand apparent power S in KVA for an apartment block with 30 consumers (each having 10 KVA of installed power) is 300 KVA.
Electrical wiring and installation course is designed to help students develop basic knowledge and skills in installing electrical wiring systems for residential, commercial, and industrial purposes. Students learn the basic concepts of electricity, electrical circuits, wiring diagrams, and safety requirements for electrical installations.
The Number of consumers, n = 30 Installed power of each consumer,
P = 10 KVA ,The total installed power, S in KVA is given by:
S = n × PS
= 300 KVA
Therefore, the total demand apparent power S in KVA for an apartment block with 30 consumers (each having 10 KVA of installed power) is 300 KVA.
To know more about on demand visit:
brainly.com/question/14456267
#SPJ11
Activity 1: A rectifier circuit is used to charge a 12 Vdc battery using a 40 Vp-p AC source. (1-a) Build a half-wave rectifier circuit with a single diode to perform the charging function. Explain the operation of the diode and the entire circuit. (1-b) Build a full-wave rectifier circuit with four diodes to perform the charging function. Explain the operation of the diodes and the entire circuit. (1-c) Evaluate the use of both circuits assuming the output of the rectifier is the battery itself in series with a 20-22 resistance. Assume negligible internal resistance of the battery and the threshold voltage of diodes. (1-d) Assuming practical diodes in the full-wave rectifier, describe the behaviour of the diodes as a p-n junction, then analyse the operation of the rectifier assuming 0.7-V threshold voltage for each diode. Use simulations to support your analysis.
The half-wave rectifier circuit charges the battery using a single diode, while the full-wave rectifier circuit uses four diodes for better efficiency and smoother charging.
In a half-wave rectifier circuit, a single diode is used to perform the charging function. The diode acts as a one-way valve for current flow, allowing current to pass through in one direction and blocking it in the opposite direction. When the positive half-cycle of the AC voltage is applied to the diode, it conducts current, allowing it to flow through the diode and charge the battery.However, during the negative half-cycle of the AC voltage, the diode becomes reverse-biased and blocks the current from flowing through, preventing discharge of the battery. This process results in a pulsating DC output with only the positive half-cycles of the AC waveform charging the battery.
In a full-wave rectifier circuit, four diodes are used to perform the charging function. The circuit configuration is known as a bridge rectifier. The diodes are arranged in a bridge configuration, allowing current to flow in the same direction through the load resistor and charging the battery during both the positive and negative half-cycles of the AC waveform.During the positive half-cycle, two diodes conduct and allow current to flow through the load resistor and charge the battery. During the negative half-cycle, the other two diodes conduct, again allowing current to flow through the load resistor and charge the battery. As a result, the output of the rectifier is a smoother DC waveform compared to the half-wave rectifier.
The half-wave rectifier circuit has a lower efficiency compared to the full-wave rectifier circuit. Since it only uses half of the AC waveform, it wastes the other half, resulting in lower charging efficiency. The full-wave rectifier, on the other hand, utilizes the entire AC waveform, making it more efficient in charging the battery.Therefore, the full-wave rectifier is a better choice for charging the battery in terms of efficiency.
In a practical full-wave rectifier with diodes having a 0.7-V threshold voltage, the behavior of the diodes can be understood as a p-n junction. During the positive half-cycle of the AC input, the diodes are forward-biased and conduct current.The voltage drop across each diode is approximately 0.7 V, allowing the remaining voltage to charge the battery. During the negative half-cycle, the diodes become reverse-biased and block current flow, preventing discharge of the battery. Simulations can be used to analyze the operation of the rectifier and observe the charging waveform and efficiency.
The simulations would demonstrate the advantages of the full-wave rectifier in terms of providing a smoother DC output and better charging efficiency compared to the half-wave rectifier.
Learn more about Rectifier
brainly.com/question/25075033
#SPJ11
A transmission line with parameters, L= 0.5 µH/m, C = 50 pF/m, G = 90 mS/m, and R = 25 /m is operating at 5 x 108 rad/s. Determine the following: (1) Propagation constant, y (11) Attenuation constant, a (iii) Phase constant, f (iv) Wavelength, (v) Characteristic impedance of the transmission line, Z, (vi) If a voltage wave travels 10 m down the line, examine the percentage of the original amplitude remains and the degrees of the phase shifted.
Given the parameters of a transmission line: L = 0.5 µH/m, C = 50 pF/m, G = 90 mS/m, and R = 25 Ω/m, and it is operating at 5 x 10⁸ rad/s.
Let us determine the following: (1) Propagation constant, y (11) Attenuation constant, a (iii) Phase constant, f (iv) Wavelength, (v) Characteristic impedance of the transmission line, Z, (vi) If a voltage wave travels 10 m down the line, examine the percentage of the original amplitude remains and the degrees of the phase shifted. The given parameters of a transmission line are: L = 0. 5 µH/m, C = 50 pF/m, G = 90 mS/m, and R = 25 Ω/m, and it is operating at 5 x 10⁸ rad/s.(1) Propagation constant:
Propagation constant (y) = √(z(γ)), where γ = (R+jωL)(G+jωC).So, γ = (25+j(5x10⁸)x0.5x10⁻⁶)(90+j(5x10⁸)x50x10⁻¹²)γ = (25+j0.25)(90+j0.25)γ = (24.95 + j22.52)The magnitude of γ = √(24.95² + 22.52²) = 33.61 Applying this value in the formula, y = 33.61 (11) Attenuation constant: Attenuation constant (a) = α = Re(γ) = 24.95Phase constant (β) = I m (γ) = 22.52(111) Wavelength:
To know more about transmission visit:-
https://brainly.com/question/33183882
#SPJ11
1. What voltage(s) should you provide when you power the Arduino through the barrel jack? How much current can be made available to the Arduino through this port? Does this port have any protection on it?
2. When you are powering the board using the barrel jack, what does the Vin pin do?
3. When you are powering the board using one of the ports mentioned above, how much current can you draw from the 5V pin? What about the 3.3V pin? What about a regular I/O (digital or analog) pin?
4. What voltage(s) should you provide when you power the Arduino through the Vin pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it?
1. The voltage supplied through the barrel jack to power the Arduino should be 7-12V. The current that can be provided by this port depends on the power supply used. It can provide up to 800 mA. Yes, it has a protection system on it.
1. The voltage supplied through the barrel jack to power the Arduino should be 7-12V. The current that can be provided by this port depends on the power supply used. It can provide up to 800 mA. Yes, it has a protection system on it.
2. When the board is powered through the barrel jack, the Vin pin is utilized to supply power to the board.3. When the board is powered via one of the ports listed, the maximum current that can be drawn from the 5V pin is 500 mA. When using the
3.3V pin, the maximum current that can be drawn is 50 mA. When using a regular I/O pin, a maximum of 40 mA can be drawn.
4. When powering the Arduino through the Vin pin, the voltage supplied should be between 7-12V. A maximum of 800 mA can be provided by this pin, and it has a protection system in place.Explanation:Arduino is a simple and easy-to-use open-source electronics platform that can be used to build a variety of projects. It's an open-source platform that can be used for a wide range of projects and applications.
One of the most important things to understand when working with an Arduino board is the power requirements and connections.
In this context, the voltage(s) that should be provided when powering the Arduino through the barrel jack is 7-12V.
This will enable the Arduino board to function efficiently. Also, the amount of current that can be made available to the Arduino through this port depends on the power supply used.
However, it can provide up to 800 mA. Furthermore, the port has a protection system in place.
When the board is powered through the barrel jack, the Vin pin is utilized to supply power to the board. When powering the board using one of the ports mentioned above, a maximum current of 500 mA can be drawn from the 5V pin. When using the 3.3V pin, the maximum current that can be drawn is 50 mA. When using a regular I/O pin, a maximum of 40 mA can be drawn.
This indicates that the voltage required when powering the Arduino through the Vin pin should be between 7-12V, and it can provide up to 800 mA. Like the barrel jack, the Vin pin also has a protection system in place.
Learn more about voltage here:
https://brainly.com/question/31347497
#SPJ11
1. (20) True or False (If you mark all True or all False, you will get zero credit.) 1) Positive voltage is required to turn on the n-channel depletion-mode MOSFET. 2) The maximum depletion width is a
The statement "Positive voltage is required to turn on the n-channel depletion-mode MOSFET" is true. It is because the MOSFET has a PN junction, and when a positive voltage is applied to the gate terminal, it attracts negative charges towards the surface and repels the positive charges away from the surface.
As a result, a depletion region is formed near the surface, which acts as an insulating layer between the gate and channel. This depletion region expands with the increase in the magnitude of the applied voltage, and beyond a certain voltage, the channel gets depleted, and the MOSFET gets turned off.
In summary, the first statement is true, and the second statement is false. The answer to the given question is:
1. (20) True or False (If you mark all True or all False, you will get zero credit.)
1) Positive voltage is required to turn on the n-channel depletion-mode MOSFET. - True
2) The maximum depletion width is a - False
To know more about MOSFET visit:
https://brainly.com/question/2284777
#SPJ11
when a pathname for a file is specified starting with a forward slash (/), it is called ______.
When a pathname for a file is specified starting with a forward slash (/), it is called an absolute pathname. An absolute pathname is a pathname that defines the location of a file or directory in a complete path starting from the root directory (/) to the file or directory in question
The root directory is the top-level directory on a file system. It's represented by a forward slash (/) in Unix-like systems and DOS/Windows systems.The root directory is located at the top of the file system hierarchy and includes all other directories and files. In Unix-like systems, absolute paths begin with the root directory and are represented by a forward slash (/).
In, the root directory is indicated by a backslash (\). Don't shorten to root when you mean the directory. In other content, use top-level folder. followed by the directories and subdirectories that the file or folder is located in.
To know more about pathname visit :-
https://brainly.com/question/32181170
#SPJ11
A digital filter is described by the difference equation y(n)=-0.9y (n-2) +0.95x(n) +0.95x(n-2) i) Find the locations of the filter's poles and zeros, and then make a rough sketch of the magnitude frequency response of the filter. What is the type of the filter? ii) Find the frequency at which H(o)=0.5
The answer is- The poles of the transfer function are [tex]z=0.9e^{-j2w}[/tex] and [tex]z=0.9e^{j2w}.[/tex], the zeros of the transfer function are [tex]z=-0.95e^{-j2w}[/tex]and [tex]z=-0.95e^{j2w}.[/tex] and we can determine that this occurs at w = 0.3316π or 1.05 radians.
i) A digital filter is described by the difference equation y(n)=-0.9y (n-2) +0.95x(n) +0.95x(n-2). The locations of the filter's poles and zeros are discussed below.
Poles: Substitute[tex]z=e^{jw}[/tex]and convert the equation to Y(z) = H(z)X(z) to get the transfer function.
The poles of the transfer function are the roots of the denominator.
As a result, the poles of the transfer function are [tex]z=0.9e^{-j2w}[/tex] and [tex]z=0.9e^{j2w}.[/tex]
Zeros: To find the zeros of the transfer function, substitute [tex]z=e^{jw}[/tex]and convert the equation to Y(z) = H(z)X(z).
The zeros of the transfer function are the roots of the numerator.
As a result, the zeros of the transfer function are [tex]z=-0.95e^{-j2w}[/tex]and [tex]z=-0.95e^{j2w}.[/tex]
Type of Filter: Since there are both poles and zeros in the right half of the s-plane, the filter is not stable.
As a result, the filter is an unstable filter.
ii) To find the frequency at which H(o)=0.5, we need to calculate the magnitude frequency response of the filter.
The magnitude frequency response of the filter is [tex]|H(e^{jw})|=|0.95+0.95e^{-j2w}|/|1+0.9e^{-j2w}|[/tex]
Therefore, [tex]0.5 =|0.95+0.95e^{-j2w}|/|1+0.9e^{-j2w}|[/tex]
Now we can find the angle at which the magnitude of the numerator is 0.5 times the magnitude of the denominator.
By using a calculator, we can determine that this occurs at w = 0.3316π or 1.05 radians.
know more about digital filter
https://brainly.com/question/33214970
#SPJ11
1. The output of a logic gate can be one of two ? 2. The output of a gate is only 1 when all of its inputs are 1 3. A Kb corresponds to 1024_bytes 4. The digit F in Hexadecimal system is equivalent to 15 in decimal system 5. IC number for NOR gate 7A 02 6. The total number of input states for 4 input or gate is 7. Write the expression for carry in Full adder AND gates 8. A 14 pin AND gate IC has 9. A+A.B= bits 10. A byte corresponds to
1. The output of a logic gate can be one of two states: 0 or 1.The output of a gate is only 1 when all of its inputs are 1. This refers to the behavior of an AND gate. A KB (kilobyte) corresponds to 1024 bytes. In computing, storage and memory sizes are often expressed in powers of
4. The digit F in the hexadecimal system is equivalent to 15 in the decimal system. In hexadecimal, the digits 0-9 represent values 0-9, and A-F represent values 10-15.
5. The IC (Integrated Circuit) number for a NOR gate is 7A 02.
6. The total number of input states for a 4-input OR gate is 16. Each input can be in one of two states (0 or 1), so the total number of possible input combinations is 2^4 = 16.
7. The expression for the carry in a full adder using AND gates can be represented as: CarryIn = A AND B, where A and B are the input bits.
8. A 14-pin AND gate IC refers to the physical package and pin configuration of the IC. It does not specify the specific IC model or manufacturer.
9. The expression A + A.B can simplify to A. This is based on the Boolean algebra property known as Idempotence, which states that A + A.B is equivalent to A.
10. A byte corresponds to a unit of digital information that consists of 8 bits. It is the fundamental storage unit in most computer systems.
Learn more about logic here:
https://brainly.com/question/2141979
#SPJ11
(a) A photovoltaic (PV) array is formed by connecting 15 PV modules in series. The PV array is connected to a central dc-dc converter and the output of the dc-dc converter is connected to an inverter. At 1000 W/m² irradiance, individual PV module maximum power point voltage (Vmp) is 18 V and maximum power point current (Imp) is 2.60 A.
(i) Calculate the power rating of each PV module and the PV array.
(ii) If the dc-dc converter voltage is required to maintain at 325 V, what should be the duty ratio/cycle of the dc-dc converter to extract maximum power at irradiance of 1000 W/m²? Use the relation VPV-array = (2D-1)xVdc-dc for the dc-dc converter, where D is the duty ratio/cycle, VPV-array is the PV array voltage or input voltage of the dc-dc converter, and Vdc-dc is the dc-dc converter output voltage or input voltage of the inverter.
(i) the power rating of the PV array is 702 W. (ii) the duty ratio/cycle of the dc-dc converter should be approximately 0.054 to extract maximum power from the PV array at an irradiance of 1000 W/m².
(i) To calculate the power rating of each PV module and the PV array, we can use the given information.
Given:
Number of PV modules (N) = 15
Individual PV module maximum power point voltage (Vmp) = 18 V
Individual PV module maximum power point current (Imp) = 2.60 A
Power rating of each PV module (Pmodule) can be calculated using the formula:
Pmodule = Vmp x Imp
Pmodule = 18 V x 2.60 A
Pmodule = 46.8 W
Therefore, each PV module has a power rating of 46.8 W.
To calculate the power rating of the PV array (Parray), we multiply the power rating of each module by the number of modules:
Parray = Pmodule x N
Parray = 46.8 W x 15
Parray = 702 W
Therefore, the power rating of the PV array is 702 W.
(ii) To determine the duty ratio/cycle of the dc-dc converter to extract maximum power at an irradiance of 1000 W/m², we use the relation VPV-array = (2D-1) x Vdc-dc, where VPV-array is the PV array voltage or input voltage of the dc-dc converter, Vdc-dc is the dc-dc converter output voltage or input voltage of the inverter, and D is the duty ratio/cycle.
Given:
VPV-array = 18 V (Vmp of individual PV module)
Vdc-dc = 325 V
To find the duty ratio D, we rearrange the equation:
D = (VPV-array / Vdc-dc + 1) / 2
D = (18 V / 325 V + 1) / 2
D = 0.054
Therefore, the duty ratio/cycle of the dc-dc converter should be approximately 0.054 to extract maximum power from the PV array at an irradiance of 1000 W/m².
Learn more about array here
https://brainly.com/question/29989214
#SPJ11
Problem 3: The LTI system in problem 2 (the original not the variant) was compensated with an integral feedforward controller as shown in the figure. Block diagram of a state feedback compensated syst
In problem 3, the LTI system from problem 2 (the original one, not the variant) was compensated with an integral feedforward controller, as shown in the figure.
Block diagram of a state feedback compensated system:
In this system, the reference input enters the block through a summing point,
and the error between the input and the output is given as input to the state-feedback controller and the integral controller.
The state-feedback controller provides a control input based on the states of the system and the integral controller computes the area under the error signal over time to provide a steady-state control input.
The state-feedback controller's transfer function is given by
G(s) = [k1 k2] / [s - 2 1],
while the integral controller's transfer function is given by
H(s) = k3 / s, where k1, k2, and k3 are controller gains.
The open-loop transfer function of the system, including both controllers,
To know more about compensated visit:
https://brainly.com/question/28250225
#SPJ11
Draw the schematic diagram that implements a 4-input AND gate using 2-input NOR gates and inverters only. Starting from the diagram of a 4-input AND gate.
To construct a 4-input AND gate using 2-input NOR gates and inverters, we'll begin with a 4-input AND gate diagram.An AND gate is a digital logic gate that produces a high output (1) only when all of its inputs are high.
A 4-input AND gate is a variation of an AND gate that takes four input signals and outputs a high signal only if all four inputs are high. The 4-input AND gate can be implemented using two-input NOR gates and inverters.To make a 4-input AND gate using 2-input NOR gates and inverters, first, invert all the inputs of the 4-input AND gate to get the complement of the input signals, then use NOR gates to create the circuit.
Finally, invert the output of the circuit to get the final result. So, the following is the circuit diagram of the 4-input AND gate using 2-input NOR gates and inverters. The output is equivalent to the AND function of the four input signals since it only produces a high output when all four input signals are high. [Figure 1: Schematic diagram of a 4-input AND gate using 2-input NOR gates and inverters]Since we are asked to describe the circuit's schematic diagram, here is the description of the circuit. The 4-input AND gate uses two inverters at the input, followed by four 2-input NOR gates, with the output of each NOR gate inverted.
To know more about inverters visit:
https://brainly.com/question/32684451
#SPJ11
A 6V DC power supply is required to power the electronic controller that controls an electric vehicle. a) State and describe the four stages of conversion to obtain the requisite power. b) Starting with an AC sinusoidal wave representing the mains supply, label the time period and the amplitude
a) State and describe the four stages of conversion to obtain the requisite power.A DC power supply is required to power the electronic controller that controls an electric vehicle. The following four stages of conversion are needed to obtain the requisite power:
Stage 1: A transformer that steps down the mains voltage to a level that is appropriate for the power supply is used. Stage 2: The rectifier is used to transform AC power to DC power, which is done by altering the AC waveform to a pulsating DC waveform. Stage 3: The output of the rectifier is then filtered to remove the ripple components, which are unwanted AC signals that can damage or hinder the functioning of electronic equipment. Stage 4: Regulators are utilized to smooth the DC output and ensure that it is stable and steady at the desired voltage level.
These circuits use voltage regulators that automatically change the output voltage to stay at the specified voltage level, despite fluctuations in the input voltage. b) Starting with an AC sinusoidal wave representing the mains supply, label the time period and the amplitude: The amplitude of an AC waveform representing the mains supply is 325V.Time Period: This refers to the length of time that it takes for the AC waveform to complete a full cycle. The time period of an AC waveform representing the mains supply is 20ms.
To know more about electric vehicle visit:
https://brainly.com/question/30714733
#SPJ11
A consumer electronics company is interested in designing a linear voltage regulator as the auxiliary power supply for their upcoming product. As an engineer, you are asked to do further investigation on this topic. With the aid of suitable diagram, explain the idea of voltage regulation and Zener diode voltage regulator
Voltage regulation is a technique of producing a regulated output voltage by converting an unregulated input voltage. Voltage regulators are of two types: 1. Linear Voltage Regulator, 2. Switching Voltage Regulator
Voltage regulators are devices that maintain a constant output voltage even when input voltage or load current is changing.
Voltage regulators are of two types:
1. Linear Voltage Regulator
2. Switching Voltage Regulator
Linear Voltage Regulator: Linear Voltage Regulator is a device that accepts an unregulated input voltage and produces a stable and fixed output voltage. They employ linear elements such as resistors and transistors to regulate the output voltage. Linear regulators are classified into two types, series, and shunt regulators.
Zener Diode Voltage Regulator: A Zener diode voltage regulator is a voltage regulator that uses Zener diodes in series with the load to regulate the voltage across the load. It is a shunt voltage regulator that shunts excess current to ground to regulate the voltage. A Zener diode operates in the reverse bias mode. A voltage source is applied in reverse direction to the Zener diode and the voltage is maintained at a specific level. The voltage regulation can be achieved by connecting a Zener diode in reverse bias with the input voltage source to create a constant voltage drop across it.
The Zener diode is reverse-biased in the Zener diode voltage regulator. As a result, the diode has a reverse saturation current, which varies slightly with temperature. As the reverse voltage across the diode rises above the Zener voltage, the reverse current through the diode increases sharply. Because of the diode's high impedance, the current is quite low if the reverse voltage is less than the Zener voltage. In this way, the Zener diode voltage regulator can be used to regulate the voltage across the load.
To know more about Voltage Regulation refer to:
https://brainly.com/question/14407917
#SPJ11
A certain op-amp has an open-loop voltage gain of 150,000. Its gain in dB is 103.5 dB
a. true
b. false
The given statement is true. The open-loop voltage gain of an op-amp is defined as the gain of the op-amp with no feedback circuit. This value is very large, often in the range of 10^5 to 10^6.
The open-loop voltage gain of an op-amp can be expressed in terms of decibels (dB), which is a logarithmic unit that indicates the ratio of two values.
The gain in decibels can be calculated using the following formula:
Gain (dB) = 20 log (Open-loop voltage gain)
Substituting the given values, we get:
Gain (dB) = 20 log (150,000)
Gain (dB) = 20 x 5.176 = 103.5 dB
Therefore, the given statement is true. The gain in dB of an op-amp with an open-loop voltage gain of 150,000 is 103.5 dB.
To know more about circuit visit :
https://brainly.com/question/12608516
#SPJ11
ClassB and ClassA have no special relationship: they are two separate classes both used by the same main client. method_b (self, class_a_object) is an instance method of classB. It takes a class object as a parameter. The main client calls method_b(). Here is an outline of the situation: class ClassA: definit__(self): self.some_memb = ... accessors, etc. class ClassB: def method_b(self, class_a_object): #main client my_obj_a ClassA() my_obj_b ClassB() my_obj_b.method_b(my_obj_a) Check all the true statements (check all that apply): If method_b () modifies the parameter class_a_object's some_memb, the client's class_a_object's some_memb will also be modified, accordingly, when the method returns. method_b () can read from (access) and/or write to (change) the parameter class_a_object's some_memb value indirectly through appropriate public ClassA methods, if ClassA offers such methods. If method_b () modifies the parameter class_a_object's some_memb, the client's class_a_object's some_memb will not be modified, accordingly, when the method returns. method_b() cannot change the parameter class_a_object's some_memb value through direct assignment, but it can access (read) it directly as in something = class_a_object.some_memb. method_b() can change the parameter class_a_object's some_memb value through direct assignment, as in class_a_object.some_memb = something.
If method_b() modifies the parameter class_a_object's some_memb, the client's class_a_object's some_memb will also be modified accordingly when the method returns.
In the given scenario, the method_b() of ClassB takes an object of ClassA as a parameter. As both ClassA and ClassB are separate classes used by the same main client, any modifications made to the parameter class_a_object within method_b() will not affect the original object held by the main client. Therefore, the statement "If method_b() modifies the parameter class_a_object's some_memb, the client's class_a_object's some_memb will also be modified accordingly when the method returns" is false. Modifying class_a_object within method_b() will only affect the copy of the object held by method_b, not the original object. However, method_b() can access and modify the class_a_object indirectly if ClassA offers appropriate public methods. By using these public methods, method_b() can read from and write to the some_memb value of class_a_object, affecting the object's internal state indirectly. In summary, modifications made to the parameter object within method_b() will not affect the original object held by the main client, but method_b() can access and modify the object indirectly through appropriate public methods provided by ClassA.
learn more about parameter here :
https://brainly.com/question/29911057
#SPJ11
T/F If crane work activities come within 6 meters (20 feet) of lines, you will need barricades to exclude: Nonessential personnel
True (T) If crane work activities come within 6 meters (20 feet) of lines, you will need barricades to exclude nonessential personnel.
A barricade is a barrier, and when working with cranes, you must barricade the area to prevent people who are not required to be there from entering the area of the crane activities.
When working near high-voltage lines, this becomes much more critical because high-voltage electrical lines are extremely hazardous.
When working on a construction project that involves cranes, the construction company must have a comprehensive plan in place to safeguard all employees and others that may come into contact with the work site, including barricades to prevent nonessential personnel from entering the work zone.
The barricades should have visible signage indicating that only authorized personnel are allowed past the barricade.
All barricades must be stable, secure, and able to prevent people from crossing the barricade line.
In conclusion, if crane work activities come within 6 meters (20 feet) of lines, you will need barricades to exclude nonessential personnel.
To know more about meters visit:
https://brainly.com/question/372485
#SPJ11
A particle is moving with a curvilinear motion as a function of time t based on x = 2t² + 3t - 1 and y = 5t - 2. Time is in seconds, and coordinates are in meters. Calculate the coordinates of the center of curvature Cat time t = 1s. X coordinate: Y coordinate:
The coordinates of the center of curvature at time t = 1s are:
X coordinate: 8 meters
Y coordinate: 3 meters
To find the center of curvature, we need to determine the radius of curvature (R) and the coordinates of the center (Cx, Cy).
Given:
x = 2t² + 3t - 1
y = 5t - 2
To find the radius of curvature (R), we can use the following formula:
R = [(1 + (dy/dt)²)^(3/2)] / |d²y/dt²|
Differentiating y with respect to t gives:
dy/dt = 5
Differentiating dy/dt with respect to t gives:
d²y/dt² = 0 (since the derivative of a constant is zero)
Substituting these values into the radius of curvature formula:
R = [(1 + 5²)^(3/2)] / |0|
R = ∞ (infinity)
Since the radius of curvature is infinite, the center of curvature lies at infinity.
However, if we interpret the problem as finding the coordinates of the center at a given time t = 1s, we can substitute t = 1 into the equations for x and y to find the coordinates of the particle at that time.
x = 2(1)² + 3(1) - 1
x = 2 + 3 - 1
x = 4 meters
y = 5(1) - 2
y = 5 - 2
y = 3 meters
At time t = 1s, the coordinates of the particle are (4, 3) meters. However, since the radius of curvature is infinite, there is no specific center of curvature associated with this curvilinear motion.
To know more about curvature, visit;
https://brainly.com/question/29595940
#SPJ11
Write a program arduino that displays on the PC screen via the serial channel the position of the Switch.
To write a program Arduino that displays on the PC screen via the serial channel the position of the switch, follow these steps:Step 1: Connect the Switch to the Arduino Board.Connect one end of the Switch to the Arduino board's digital pin 2 and the other end to the ground pin.
Step 2: Connect the Arduino Board to the ComputerConnect the Arduino board to your computer using the USB cable.Step 3: Open the Arduino IDEOpen the Arduino IDE and create a new sketch.Step 4: Add the Code to the SketchNow, add the following code to the sketch:
const int switchPin = 2; // set the pin the switch is connected to int switchState = 0;
// variable for reading the switch status void setup()
{ // initialize serial communication:
Serial.begin(9600);
// initialize the switch pin as an input:
pinMode(switchPin, INPUT); } void loop()
{ // read the switch state:
switchState = digitalRead(switchPin);
// send the switch state to the serial port: Serial.println(switchState);
// wait a little before reading again delay(100); }
Step 5: Verify and Upload the Code Verify and upload the code to the Arduino board.Step 6: Open the Serial Monitor Open the Serial Monitor in the Arduino IDE by clicking on the magnifying glass icon on the top right corner of the IDE or go to Tools > Serial Monitor.Step 7: View the Switch Position Now, when you toggle the switch, you will see the position of the switch displayed on the PC screen via the serial channel. The value will either be 0 or 1, depending on the switch position. The program will continue to update the position of the switch every 100 milliseconds.
To know more about Arduino visit:
https://brainly.com/question/30758374
#SPJ11
Create a code in C++ on the page https://replit.com/Create a Complex class that allows working with complex numbers (real part and imaginary part), and that has the methods to read both real and complex values and print them. Write a program that generates an array of n complex numbers and allows: adding and subtracting the n complex numbers.
The program deallocates the memory allocated for the array of complex numbers using the delete[] operator.
Here's an example code in C++ that defines a Complex class and allows working with complex numbers (real part and imaginary part) by implementing methods to read and print the complex values, as well as performing addition and subtraction operations on an array of complex numbers:
```cpp
#include <iostream>
class Complex {
private:
double real;
double imaginary;
public:
Complex(double r = 0.0, double i = 0.0) {
real = r;
imaginary = i;
}
void readComplex() {
std::cout << "Enter real part: ";
std::cin >> real;
std::cout << "Enter imaginary part: ";
std::cin >> imaginary;
}
void printComplex() {
std::cout << real << " + " << imaginary << "i" << std::endl;
}
Complex operator+(const Complex& other) const {
double r = real + other.real;
double i = imaginary + other.imaginary;
return Complex(r, i);
}
Complex operator-(const Complex& other) const {
double r = real - other.real;
double i = imaginary - other.imaginary;
return Complex(r, i);
}
};
int main() {
int n;
std::cout << "Enter the number of complex numbers: ";
std::cin >> n;
Complex* complexNumbers = new Complex[n];
// Read complex numbers
for (int i = 0; i < n; i++) {
std::cout << "Enter Complex Number " << (i + 1) << std::endl;
complexNumbers[i].readComplex();
}
// Print complex numbers
std::cout << "Complex Numbers:" << std::endl;
for (int i = 0; i < n; i++) {
std::cout << "Complex Number " << (i + 1) << ": ";
complexNumbers[i].printComplex();
}
// Perform addition
Complex sum;
for (int i = 0; i < n; i++) {
sum = sum + complexNumbers[i];
}
std::cout << "Sum of Complex Numbers: ";
sum.printComplex();
// Perform subtraction
Complex difference = complexNumbers[0];
for (int i = 1; i < n; i++) {
difference = difference - complexNumbers[i];
}
std::cout << "Difference of Complex Numbers: ";
difference.printComplex();
delete[] complexNumbers;
return 0;
}
```
In this code, the Complex class represents a complex number with attributes for the real and imaginary parts. It has methods to read and print the complex values, as well as overloaded operators for addition (+) and subtraction (-) of complex numbers.
In the main function, the user is prompted to enter the number of complex numbers. Then, an array of Complex objects is created dynamically using the new operator. The user is then prompted to enter the real and imaginary parts for each complex number.
After that, the program prints all the entered complex numbers. It then performs addition and subtraction operations on the array of complex numbers using the overloaded operators. The result of the addition and subtraction is printed as well.
Finally, the program deallocates the memory allocated for the array of complex numbers using the delete[] operator.
You can customize the code to suit your needs, such as adding more operations or modifying the complex number input process.
Learn more about array here
https://brainly.com/question/29989214
#SPJ11
When the source and relay pumpers are ready, the discharge supplying the hoseline on the source pumper is:
Select one:
a. closed and the valve on the dump line is closed.
b. opened and the valve on the dump line is opened.
c. closed while the valve on the dump line is opened.
d. opened while the valve on the dump line is closed.
When the source and relay pumpers are ready, the discharge supplying the hoseline on the source pumper is opened while the valve on the dump line is closed. Relay pumping is a technique used to transport water from a water source that is insufficient to meet the demands of a fire department.
By using two or more fire pumps, each pumper can refill the one ahead of it while simultaneously discharging water to the fire through a hoseline. Related: What is relay pumping.
Relay pumping consists of a number of pumps spaced at intervals between a water source and the incident. Multiple pumps are used to overcome pressure and flow losses due to friction and head. A quick-fill portable can be used as one of the relay points.
To know more about Relay pumping visit :-
https://brainly.com/question/30454736
#SPJ11
A three-phase transformer rated 5 MVA, 115/13.2 kV has per-phase series impedance of (0.007+j0.075) per unit. The transformer is connected to a short distribution line which can be represented by series impedance per phase of (0.02+j0.10) per unit on a base of 10 MVA, 13.2 kV. The line supplies a balanced three-phase load rated 4 MVA, 13.2 kV, with lagging power factor of 0.85. Neglect the magnetizing branch of the transformer: a) Sketch a single-phase equivalent circuit of the system indicating all impedances in per unit on 10 MVA, 13.2 kV base quantities at the load [10 pts] b) Find the complex power supplied by the source connected to the primary of the transformer [10 pts] c) Calculate the voltage regulation at the load [5 pts]
Single-phase equivalent circuit of the system indicating all impedances in per unit on 10 MVA, 13.2 kV base quantities at the load:
Thus, the per unit transformer impedance is: Z pu = (Z1 / 5x10^6) * (115 kV / (13.2 kV / √3))^2Zpu = (0.007 + j0.075) pub) Complex power supplied by the source connected to the primary of the transformer: At the load, the current is given by:
I2 = (V2 - V Load) / (Z pu + Z2 + Z Load) = 0.8704 - j0.2253 pu
The apparent power supplied to the load is:
S2 = 3 x VLoad x I2* = 4 MVA x 0.85 = 3.4 MVAThus, the complex power supplied by the source connected to the primary of the transformer is:
S1 = S2 / a^2 + I1^2(Zpu + Z2) = 13.143 MVA - j6.821 MVAc) Voltage regulation at the load:The voltage regulation at the load is given by:
VLoad, actual = VLoad, nominal / (1 + 3 x I2*Zpu)
VLoad, actual = 13.2 kV / (1 + 3 x 0.8704 + j0.2253 x 0.007 - j0.2253 x 0.075)
VLoad, actual = 12.312 - j0.725 kVThe magnitude of the voltage regulation is:
% voltage regulation = (|VLoad, actual| - |VLoad, nominal|) / |VLoad, nominal| x 100%
% voltage regulation = (12.312 - 13.2) / 13.2 x 100% = -6.67%The voltage regulation at the load is -6.67%.
To know more about equivalent visit:-
https://brainly.com/question/14947697
#SPJ11
The instantaneous frequency of the modulation signal, which is frequency modulated with the x(t)=cos2000πt message signal, can deviate at most 2kHz from the carrier frequency.
a) Find the bandwidth required to transmit the frequency modulation signal according to Carson's rule.
b) What is the bandwidth when the frequency of the message signal is changed to 2kHz?
c) What is the bandwidth required to double the amplitude of the message signal in part a?
d) Since the carrier is 1V-10MHz, draw the spectra of the modulation signal for a,b,c in the frequency band determined by the Carson rule and calculate the transmission powers separately.
a) Bandwidth required to transmit the frequency modulation signal is 8 kHz b) Bandwidth required to transmit FM signal is 8 kHz is 2 kHz.c) The new bandwidth of the FM wave will be, B.W is 4 MHz d) Transmission power for part a = 0.01 mW Transmission power for part b = 0.01 mW Transmission power for part c = 0.04 mW
a) Bandwidth required to transmit the frequency modulation signal according to Carson's rule is given as,
B.W = 2(Δf + fm)
where, Δf = Maximum frequency deviation
fm = Maximum message signal frequency
For the given question,
Message signal: x(t) = cos(2π 2000t)
Carrier signal: c(t) = cos(2π 10^6 t)
Voltage of the carrier signal = 1 V and the frequency of the carrier signal = 10 MHz
Maximum frequency deviation is 2 kHz
fm = 2000 HzThus, Δf = 2 kHzB.
W = 2(Δf + fm) = 2(2 kHz + 2000 Hz)= 8 kHz
b)
Given that, message signal frequency = 2 kHz
We know that bandwidth of an FM wave depends on the highest frequency in the message signal,
Therefore, the bandwidth of the FM wave will not change when the frequency of the message signal is changed to 2 kHz.
Bandwidth required to transmit FM signal is 8 kHz, and this will remain the same even if we change the message signal frequency to 2 kHz.
c)
Given that,
Amplitude of the message signal is doubled
Therefore, new message signal is, x(t) = 2cos(2π 2000t) = cos(2π 2000t) + cos(2π 2000t)
By trigonometric identity, 2cosθ = cos θ + cos θ = Re [e^(jθ) + e^(-jθ)]
∴ 2cos(2π 2000t) = Re [e^(j2π 2000t) + e^(-j2π 2000t)]
Therefore, the new message signal will consist of two message signals having frequencies 2 MHz and -2 MHz respectively.The highest frequency is 2 MHz.
Hence, the new bandwidth of the FM wave will be, B.W = 2(Δf + fm) = 2(2 kHz + 2 MHz)= 4.004 MHz ≈ 4 MHz
d) The spectra of the modulation signal for a, b, and c can be shown as follows:
For a: Modulation index, m = Δf/fm = 2/2000 = 0.001Using Bessel table, the amplitude of each component is given below:
For b:For c:Transmission power can be calculated using the following formula,P = (V_rms )^2/Rwhere,V_rms = rms value of the signal R = Resistance
We know that,V_p = 1 V
Peak-to-peak voltage,
V_rms = V_p/√2 = 0.707
VR = 50 Ω
Thus,For part a,P = (V_rms )^2/R = (0.707 V)^2 /50 Ω = 0.01 mW
For part b,P = (V_rms )^2/R = (0.707 V)^2 /50 Ω = 0.01 mW
For part c,P = (V_rms )^2/R = (1.414 V)^2 /50 Ω = 0.04 mW
Therefore, Transmission power for part a = 0.01 mW Transmission power for part b = 0.01 mW Transmission power for part c = 0.04 mW
Learn more about Bandwidth here:
https://brainly.com/question/13440320
#SPJ11
You support a laptop owner who has been using the laptop at home for several years. Now the user reports that the laptop is unstable and shuts down suddenly after a few hours of use. What should you do first?
The first thing that you need to do is to troubleshoot the problem. Here are some of the steps that you can take to address the issue: Check the power supply and battery: Ensure that the laptop is receiving the required power supply and that the battery is charging properly.
You can use a multimeter to check the voltage and amperage levels. If the power supply or battery is faulty, then you may need to replace them. Remove dust and debris: Over time, dust and debris can accumulate inside the laptop, which can cause it to overheat and shut down.
Use a can of compressed air to blow out the dust from the cooling vents and fans. This will improve airflow and reduce the risk of overheating. Check for software issues: Some software applications may be causing the laptop to crash or shut down.
Check the event viewer logs to see if there are any error messages related to software issues. You can also run a virus scan to check for malware or viruses that may be causing the problem.
Upgrade hardware: If the laptop is old and outdated, then upgrading the hardware components such as RAM or hard drive can help to improve its performance and stability.
Learn more about troubleshoot at https://brainly.com/question/14600167
#SPJ11
1) Determine and correct the errors in the following programs? (10 points) 1 #include 2 int main() 3-{ int length, width, area; 5 area = length * width; 6 6 length = 20; ; 7 width 15; 8 cout << "The area is area; 9 return ; 10} 11 12
There are multiple errors in the code provided. Here's the corrected code:
#include <iostream>
using namespace std;
int main() {
int length = 20, width = 15, area;
area = length * width;
cout << "The area is " << area << endl;
return 0;
}
Explanation of the corrections made:
Line 1: Added missing iostream header file.
Line 3: Added opening curly brace {.
Lines 4-5: Declared and initialized variables length, width, and area.
Line 6: Removed extra semicolon ;.
Line 7: Corrected assignment operator = instead of missing equal sign =.
Line 8: Enclosed output message with quotes " " and added << endl to print a new line after the message.
Line 9: Added return 0; statement.
Line 10: Added closing curly brace }.
learn more about code here
https://brainly.com/question/17204194
#SPJ11
Write a machine code program (0's and 1's) for the LC3. It should print out the letters:
Writing a complete machine code program in binary (0's and 1's) for the LC3 architecture can be quite complex and time-consuming. Instead, I can provide you with a simplified assembly language program for the LC3 that prints out the letters of the alphabet. The LC3 assembly code can then be assembled into machine code using an LC3 assembler.
Here's an example LC3 assembly code that prints out the letters:
```
.ORIG x3000
LEA R0, LETTERS ; Load effective address of the letters array
AND R1, R1, #0 ; Clear R1 to use as a counter
ADD R2, R2, #26 ; Set R2 to 26 (number of letters)
LOOP:
LDR R3, R0, #0 ; Load a letter from memory
OUT ; Output the letter
ADD R0, R0, #1 ; Increment the memory address
ADD R1, R1, #1 ; Increment the counter
ADD R4, R1, R2 ; Check if the counter equals 26
BRz END ; If equal, end the program
BRnzp LOOP ; Otherwise, continue the loop
END:
HALT
LETTERS:
.STRINGZ "ABCDEFGHIJKLMNOPQRSTUVWXYZ"
.END
```
This LC3 assembly program uses a loop to iterate through the letters stored in the `LETTERS` array and outputs them using the `OUT` instruction. It uses registers R0, R1, R2, and R3 for various purposes, such as storing memory addresses and counters. The program ends when all letters have been printed, indicated by the counter reaching 26.
Once you have the assembly code, you can use an LC3 assembler (such as LC3Edit or LC3Sim) to assemble it into machine code. The resulting machine code can then be executed on an LC3 simulator or hardware.
Learn more about assembly code here:
https://brainly.com/question/31590404
#SPJ11
Step by step guide
Q10 The unit step response of an arbitrary system is plotted below: (i) Determine the peak overshoot and the steady-state error for this system. Peal ovecshart \( =1 \) sterly stak output is I 1 (ii)
The peak overshoot and the steady-state error for the system with the given unit step response in the image attached can be determined as follows:
Step 1: First, we find the percentage overshoot using the formula:
[tex]$$\% OS = \frac{Max\:Overshoot}{Final\:Steady-State\:Value} \times 100$$.[/tex]
From the given unit step response, we can see that the maximum overshoot occurs at 2.5 seconds and is equal to 1.2 units. Therefore, the percentage overshoot is:
[tex]$$\% OS = \frac{1.2}{1} \times 100 = 120\%$$[/tex]
Step 2: Next, we find the damping ratio (ζ) using the percentage overshoot:
[tex]$$\% OS = e^{-\frac{\zeta \pi}{\sqrt{1-\zeta^2}}} \[/tex]times [tex]100$$Solving for ζ, we get:$$\zeta = \frac{-\ln(\%OS/100)}{\sqrt{\pi^2 + \ln^2(\%OS/100)}}$$[/tex].
Substituting the value of percentage overshoot (120%), we get:[tex]$$\zeta = 0.445$$[/tex].
Step 3: Using the damping ratio, we can find the natural frequency (ωn) using the formula:[tex]$$\omega_n = \frac{4}{\zeta T_p}$$[/tex].
Where Tp is the time taken by the system to reach the first peak overshoot after the step input is applied.
To know more about system visit:
https://brainly.com/question/19843453
#SPJ11
Mention and discuss the modes of operation of a synchronous machine.
The modes of operation of a synchronous machine are generator mode, motor mode, and synchronous condenser mode.
What are the modes of operation of a synchronous machine?The synchronous machine, also known as a synchronous generator or motor, operates in different modes depending on its configuration and the connection to the electrical grid. Here are the three primary modes of operation:
1. Generator Mode: In this mode, the synchronous machine operates as a generator, converting mechanical energy into electrical energy. The prime mover (such as a steam turbine or a hydro turbine) drives the rotor, creating a rotating magnetic field. The interaction between the rotor magnetic field and the stator windings induces voltage and current in the stator, generating electrical power. The generator mode is commonly used in power plants to produce electricity.
2. Motor Mode: In motor mode, the synchronous machine operates as a motor, converting electrical energy into mechanical energy. A three-phase AC power supply is provided to the stator windings, creating a rotating magnetic field. This magnetic field interacts with the rotor, causing it to rotate and perform mechanical work. The motor mode is used in various applications, such as driving pumps, compressors, and industrial machinery.
3. Synchronous Condenser Mode: In this mode, the synchronous machine operates as a reactive power compensator or voltage regulator. The machine is usually overexcited, meaning that the field current is increased beyond what is necessary for generating active power. By controlling the field current, the synchronous machine can supply or absorb reactive power to stabilize the voltage and improve the power factor of the electrical system. Synchronous condensers are commonly used in power systems to provide voltage support and enhance system stability.
It's worth noting that the synchronous machine operates in a synchronous manner, meaning that the rotor speed is synchronized with the frequency of the electrical grid. This synchronization is achieved by adjusting the field current or applying a suitable control mechanism.
Each mode of operation has its own characteristics and applications, making the synchronous machine a versatile and essential component in power generation, transmission, and distribution systems.
Learn more about synchronous
brainly.com/question/27189278
#SPJ11
Assume a neutron point source emitting neutron of 0.1 eV with an intensity of 4.18e17
neutron/second, the source is surrounded by a sphere shell of Uranium-235 (density = 19
g/cm^3), the inner radius of the shell is 10 cm and the outer radius of the shell is 12 cm.
If the sphere is under irradiation for 10 days, please:
1. If you use FLUKA code, please calculate the Mo-99 activity in 10 days irradiation (time internal 1 day)
2. If you do not have access to computer, then assume fission is 2.09 fission/primary
neutron, and the yield of Mo-99 is 0.062 per fission, please use analytical method to
calculate Mo-99 activity in 10 days irradiation (time interval 1 day)
The Mo-99 activity produced in 10 days Irradiation is 2.40599 × 10³² disintegrations.
The given data is as follows: Intensity of Neutrons: 4.18×10¹⁷ neutron/sec
Energy of Neutrons: 0.1 eV
Sphere shell of Uranium-235 Density of Uranium-235: 19 g/cm³
Inner radius: 10 cm
Outer radius: 12 cm
Duration of Irradiation: 10 days
1. Calculation of Mo-99 activity in 10 days Irradiation:
Using the FLUKA code, the Mo-99 activity in 10 days Irradiation can be calculated.
2. Calculation of Mo-99 activity in 10 days Irradiation:
Considering the yield of Mo-99 is 0.062 per fission, and fission is 2.09 fission/primary neutron.
Therefore, the number of Mo-99 produced per neutron can be calculated as follows:
Number of Mo-99 produced per primary neutron = Yield of Mo-99 × Fission per primary neutron= 0.062 × 2.09 = 0.12958
Therefore, the activity of Mo-99 produced per primary neutron can be calculated as follows:
Activity of Mo-99 produced per primary neutron= (Number of Mo-99 produced per primary neutron) × (Disintegration rate of Mo-99)= 0.12958 × 1.44 × 10⁶= 1.8656 × 10⁵ disintegrations/sec
Now, the intensity of neutron is 4.18 × 10¹⁷ neutron/sec.
Hence, the number of neutron will be:
N = Intensity of neutron × Time= 4.18 × 10¹⁷ × 10 × 24 × 3600= 1.284288 × 10²⁴
The total number of Mo-99 produced in the given duration can be calculated by the following formula:
Number of Mo-99 produced in the given duration= (Number of Mo-99 produced per primary neutron) × (Number of primary neutron)× (Duration of Irradiation)= 0.12958 × 1.284288 × 10²⁴ × 10= 1.66992 × 10²⁶
The total activity of Mo-99 produced in 10 days Irradiation can be calculated by the following formula:
Activity of Mo-99 produced in 10 days Irradiation= (Number of Mo-99 produced in the given duration) × (Disintegration rate of Mo-99)= 1.66992 × 10²⁶ × 1.44 × 10⁶= 2.40599 × 10³² disintegrations.
Learn more about inner radius at
https://brainly.com/question/15397466
#SPJ11
