The energy required to break the hydrogen bond at the midway point can be calculated using the formula for electrostatic interaction. The electric potential midway between the two H2O molecules can also be determined using the given charges and distances.
(a) To calculate the energy required to break the hydrogen bond at the midway point, we need to determine the electrostatic interaction among the four charges involved. The charges given in the figure are -0.35e, +0.356e, -0.35e, and +0.35e. We can use the formula for the electrostatic potential energy:
Energy = k * q1 * q2 / r
Where k is the Coulomb constant (8.988 × 10^9 Nm^2/C^2), q1 and q2 are the charges, and r is the distance between them. In this case, q1 and q2 are the charges at the midway point (-0.35e and +0.356e) and the distance between them is 0.10 nm. Plugging in the values, we get:
Energy = (8.988 × 10^9 Nm^2/C^2) * (-0.35e) * (+0.356e) / (0.10 nm)
(b) To calculate the electric potential midway between the two H2O molecules, we can use the formula for electric potential:
Electric potential = k * q / r
Where k is the Coulomb constant, q is the charge, and r is the distance. In this case, the charge q is the sum of the charges at the midway point (-0.35e and +0.35e) and the distance r is 0.10 nm. Plugging in the values, we get:
Electric potential = (8.988 × 10^9 Nm^2/C^2) * (-0.35e + 0.35e) / (0.10 nm)
Learn more about energy
brainly.com/question/1932868
#SPJ11
Two 5 mm x 5 mm electrodes are held 0.10 mm apart and are attached to a 9 V battery. Without disconnecting the battery, a 0.1 mm thick sheet of Mylar is inserted between the electrodes. What are the capacitor's charge before and after the Mylar is inserted. Dielectric constant of Mylar is 3.1 Obefore 95 pC (pico-Coulomb) and after 205 pC. Obefore 418 PC (pico-coulomb) and after 607 pc. Obefore 20 pC (pico-Coulomb) and after 62 pC. capacitor's charge is equal before and after the Mylar is inserted Obefore 148 PC (pico-Coulomb) and after 315 pC.
The correct options are:O before 95 pC (pico-Coulomb) and after 205 pC.O before 418 PC (pico-coulomb) and after 607 pc.O before 20 pC (pico-Coulomb) and after 62 pC.O before 148 PC (pico-Coulomb) and after 315 pC.
Given the conditions are;Two 5 mm x 5 mm electrodes are held 0.10 mm apart and are attached to a 9 V battery.A 0.1 mm thick sheet of Mylar is inserted between the electrodes.Dielectric constant of Mylar is 3.1The initial charge of the capacitor is 95 pC, 418 pC, 20 pC, and 148 pC before the Mylar is inserted.The final charge of the capacitor is 205 pC, 607 pc, 62 pC, and 315 pC after the Mylar is inserted.Therefore, we know that the capacitance of the capacitor changes with the introduction of the dielectric. The charge Q stored on a capacitor is Q
= CV where V is the potential difference between the plates. Therefore, when a dielectric is inserted between the plates, the capacitance increases by a factor of κ, the dielectric constant of the material. This factor is given by the expression:κ
= C/C0 where C0 is the capacitance without the dielectric, and C is the capacitance with the dielectric.Therefore, we can find the capacitance before and after the introduction of Mylar by multiplying the initial capacitance with the dielectric constant of Mylar and compare it with the final capacitance. The correct answer is:O before 95 pC (pico-Coulomb) and after 205 pC. O before 418 PC (pico-coulomb) and after 607 pc. O before 20 pC (pico-Coulomb) and after 62 pC.O before 148 PC (pico-Coulomb) and after 315 pC.The correct options are:O before 95 pC (pico-Coulomb) and after 205 pC.O before 418 PC (pico-coulomb) and after 607 pc.O before 20 pC (pico-Coulomb) and after 62 pC.O before 148 PC (pico-Coulomb) and after 315 pC.
To know more about correct visit:
https://brainly.com/question/23939796
#SPJ11
If the aircraft develops a left wing down roll rate, what type of moment is produced by the gyroscopic moment (pos/neg. pitch, roll, or yaw)
If the aircraft pitches downward, what type of moment is produced?
If the aircraft yaws to the left, what type of moment is produced?
The case of aircraft, the gyroscopic effect produces moments that are perpendicular to the plane of rotation.
When an aircraft develops a left wing down roll rate, the gyroscopic moment produced is known as the positive pitch moment.
A gyroscopic moment is produced by the gyroscopic effect, which is caused by the rotation of the engine, and it acts in a direction perpendicular to the plane of rotation.
When the aircraft pitches downward, a negative pitch moment is produced by the gyroscopic moment.
When the aircraft yaws to the left, a positive yaw moment is produced by the gyroscopic moment. This is due to the fact that the axis of the spinning propeller tilts in the direction of the yaw, which causes a gyroscopic moment in the opposite direction, causing the aircraft to yaw in the opposite direction.
Therefore, it can be said that in the case of aircraft, the gyroscopic effect produces moments that are perpendicular to the plane of rotation.
Learn more about gyroscopic effect from :
https://brainly.com/question/29509090
#SPJ11
A potential drop of 50 volts is measured across a 250 0 resistor. What is the power in the resistor (Enter the number only)
The power in the resistor is 10 W.
Given: A potential drop of 50 volts is measured across a 250 Ω resistor.
The power in the resistor.
We know that Power (P) = V^2/R , where V is voltage and R is resistance.
Therefore, substituting the given values, we have;
Power [tex](P) = V^2/R = (50 V)^2/(250 Ω)[/tex]
= [tex](2500 V^2)/(250 Ω)[/tex]
= [tex]10 V^2 = 10 W[/tex]
Thus, the power in the resistor is 10 W.
Learn more about resistor
brainly.com/question/30672175
#SPJ11
2. An ideal rectangular waveguide, filled with air, having a transversal section of a=1.5cm, b=0.8cm, working at the frequency f-100GHz has the expression of the magnetic field component on Ox axis: 3my H₂=2sin 2 sin ( cos(37) A/m Determine: 1) the mode corresponding to the expression of Hx 2) the critical frequency 3) the phase constant the propagation constant 5) the wave impedance for the mode determined at point 1).
1) The mode corresponding to the expression of Hx is the TE10 mode.
2) The critical frequency for the TE10 mode is 150 GHz.
3) The phase constant for the TE10 mode is 125.66 rad / cm.
4) The propagation constant for the TE10 mode is approximately equal to 125.66 rad / cm.
5) The wave impedance for the TE10 mode is 377 Ω.
1) The mode corresponding to the expression of Hx is the TE10 mode. This is because the expression of Hx has only one sine term, and the TE10 mode is the only mode that has only one sine term.
2) The critical frequency is the frequency at which the first mode can propagate. The critical frequency for the TE10 mode is given by the following equation:
fc = c / (2 * a * b)
c is the speed of light in free space
a is the width of the waveguide
b is the height of the waveguide
fc = 3 * 10^8 m / s / (2 * 1.5 cm * 0.8 cm) = 150 GHz
Therefore, the critical frequency for the TE10 mode is 150 GHz.
3) The phase constant is the rate at which the phase of the wave changes as it propagates along the waveguide. The phase constant for the TE10 mode is given by the following equation:
β = 2π / (a * b)
β is the phase constant
a is the width of the waveguide
b is the height of the waveguide
β = 2π / (1.5 cm * 0.8 cm) = 125.66 rad / cm
Therefore, the phase constant for the TE10 mode is 125.66 rad / cm.
4) The propagation constant is the rate at which the amplitude of the wave changes as it propagates along the waveguide. The propagation constant for the TE10 mode is given by the following equation:
γ = β + j * α
γ is the propagation constant
β is the phase constant
α is the attenuation constant
The attenuation constant for the TE10 mode in air is negligible, so the propagation constant is approximately equal to the phase constant.
Therefore, the propagation constant for the TE10 mode is approximately equal to 125.66 rad / cm.
5) The wave impedance for the TE10 mode is given by the following equation:
Z = μ0 / ε0
Z is the wave impedance
μ0 is the permeability of free space
ε0 is the permittivity of free space
Z = 377 Ω
Therefore, the wave impedance for the TE10 mode is 377 Ω.
To learn more about wave impedance: https://brainly.com/question/32615445
#SPJ11
A fay of light strikes the midpoint of ore face of an equlangular (60
6
−634−600
6
) giass \{a) Trace the gath of the light ray throwgh the giass, and find the angles of incidance and refractian at each ourface. First surface: θ
inciatence
= 9
rufracsian
= Second surfoce: θ
incience
= 9
refration
= (o) If a whall fraction of light is also reflected at each surface, Find the agies of reflection at the suraces. θ
refeann
= - (second surface)
The path of the light ray through the glass and find the angles of incidence and refraction at each surface. Given that a ray of light strikes the midpoint of one face of an equilateral (60 degree) glass prism.
Let us consider the following diagram of the given problem: Since the ray is normal to the surface it does not bend at the entry point. So, θincidence = 0° for the first surface.The angle of incidence for the second surface of the prism is equal to the angle of refraction of the first surface. Since the first surface does not bend the light, θrefraction of the first surface = 0°.
Hence, θincidence = 0° for the second surface.Using Snell's law for the first surface of the prism, we get
;[tex]\frac{\sin\theta_i}{\sin\theta_r}=\frac{n_2}{n_1}[/tex]Here, [tex]\theta_i[/tex] = incidence angle, [tex]\theta_r[/tex] = refraction angle, [tex]n_1[/tex] = refractive index of air and [tex]n_2[/tex] = refractive index
of the glass prismWe know that the glass prism is made of equilateral glass.
Hence the refractive index for equilateral glass is 1.5. Using this value, we get:
[tex]\frac{\sin 30}{\sin\theta_r}=\frac{1.5}{1}[/tex][tex]\theta_r=19.47\degree[/tex]
For the second surface, the ray enters into the air from the glass. Hence, [tex]n_1[/tex] = 1 and [tex]n_2[/tex] = 1.5. Using Snell's law, we get
;[tex]\frac{\sin\theta_i}{\sin\theta_r}=\frac{n_2}{n_1}[/tex][tex]\frac{\sin\theta_i}{\sin 30}=\frac{1.5}{1}[/tex][tex]\sin\theta_i=0.75[/tex][tex]\theta_i=48.59\degree[/tex].
Thus, the angles of incidence and refraction at each surface are given as below:
First surface: [tex]\theta_{incidence}=0\degree[/tex] and [tex]\theta_{refraction}=19.47\degree[/tex]Second surface: [tex]\theta_{incidence}=48.59\degree[/tex] and [tex]\theta_{refraction}=0\degree[/tex]
The angle of reflection is equal to the angle of incidence. Hence, θreflection = θincidence. Thus, θreflection = 0° for the first surface and θreflection = 48.59° for the second surface.
To know more about refraction visit:
https://brainly.com/question/32684646
#SPJ11
A motorcycle patrolman starts from rest at A two seconds after a car, speeding at the constant rate of 120km/h, passes point A. If the patrolman accelerates at the rate of 6m/s^2 until he reaches his maximum permissible speed of 150km/h, which he maintains, calculate the distance from point A to the point at which be overtakes the car
The distance from point A to the point at which the patrolman overtakes the car is 2700 meters.
The distance from point A to the point at which the motorcycle patrolman overtakes the car is 2700 meters. Here's a step-by-step breakdown of the calculations:
Step 1:
Distance covered by the car in 2 seconds:
Distance = Speed * Time
Speed = 120 km/hr = (120/3600) m/s = (1/30) m/s
Time = 2 seconds
Distance = (1/30) m/s * 2 s = 2/30 km = (2/30) * 1000 m = 66.67 m
Step 2:
Calculating the time taken by the motorcycle patrolman to reach a speed of 150 km/h:
Using the equation v = u + at
Initial velocity (u) = 0 m/s
Final velocity (v) = 150 km/h = (150000/3600) m/s = (125/3) m/s
Acceleration (a) = 6 m/s^2
(125/3) m/s = 0 m/s + 6 m/s^2 * t
Solving for t:
t = (125/3) / 6 sec = (125/3) * (1/6) sec = 125/18 sec
Step 3:
Calculating the distance covered by the motorcycle patrolman in the first (125/18) seconds:
Using the equation s = ut + (1/2)at^2
Initial velocity (u) = 0 m/s
Acceleration (a) = 6 m/s^2
Time (t) = 125/18 sec
s = 0 * (125/18) + (1/2) * 6 * ((125/18)^2) = 1562.5/9 m
Step 4:
Calculating the time taken by the motorcycle patrolman to overtake the car:
Let the time taken be t sec
Speed of the car = 120 km/hr = (100/3) m/s
Distance covered by the car in time t = (100/3) m/s * t
Distance covered by the motorcycle patrolman in time t = Distance covered by the car in time t + Distance covered by the motorcycle patrolman in the first (125/18) sec
Time taken = (Distance to be covered) / (Speed of the motorcycle patrolman)
= (Distance covered by the motorcycle patrolman in time t - Distance covered by the motorcycle patrolman in the first (125/18) sec) / [(150000/3600) m/s]
= [(100/3) * t + 1562.5/9 - 1562.5/9] / [(150000/3600)] sec
= [(100/3) * t] / [(150000/3600)] sec
= (1/45) * t sec
The two times should be equal, so we can set up the equation:
(100/3) * t + 1562.5/9 = (1/45) * t
Solving for t:
(3200/45) * t + 1562.5/9 = t
[(3200/45) - (1/45)] * t = 1562.5/9
t = (1562.5 * 45) / (9 * 3199) sec
Step 5:
Distance from point A to the point at which the motorcycle patrolman overtakes the car:
Distance = Distance covered by the motorcycle patrolman in the first (125/18) sec + Distance covered by the motorcycle patrolman in time t
Distance = 1562.5
/9 + [(100/3) * t + 1562.5/9 - 1562.5/9] m
= 1562.5/9 + (100/3) * (1562.5 * 45) / (9 * 3199) m
= 1562.5/9 + 10425/3199 m
= [(1562.5 * 3199) + 10425] / 28791 m
= 2700 m
Therefore, the distance from point A to the point at which the motorcycle patrolman overtakes the car is 2700 meters.
Learn more about distance here :-
https://brainly.com/question/31713805
#SPJ11
A Type la supernova occurs when
a.• one solar mass of matter combines with one solar mass of antimatter.
b• several novae occur simultaneously.
c• the core of a high mass star collapses and forms a white dwarf.
A Type la supernova occurs when the core of a high mass star collapses and forms a white dwarf.
So, the correct answer is C.
What is a Type Ia supernova?A type Ia supernova is a type of supernova that occurs when a white dwarf star in a binary system reaches a critical mass limit and explodes. The white dwarf's mass gradually increases as it consumes matter from its companion star until it reaches a mass of around 1.4 solar masses, known as the Chandrasekhar limit. When this mass is exceeded, a runaway nuclear reaction occurs, causing the star to explode in a Type Ia supernova event.
Type Ia supernovae are critical for astronomy because they can be used to determine the distance to distant galaxies. Because these supernovae all have the same intrinsic brightness, their observed brightness is determined solely by their distance from Earth. By comparing their apparent brightness to their known intrinsic brightness, astronomers can estimate the distance to their host galaxies.
Therfore, the correct answer is C.
Learn more about supernova at https://brainly.com/question/29805203
#SPJ11
a) Calculate the new inductance of a coil if the number of loops is doubled.
b) Calculate the number of loops required to design an AC generator working at 110 V and 60 Hz with 0.15 Tesla Magnetic Field and each loop has an area of 2.0 m^2.
c) Calculate the number of loops on the secondary coil of a step-down transformer used in a cell phone charger requiring 3.7 V at its secondary coil. If the primary has 110 V and 1000 loops.
a) When the number of loops in a coil is doubled, the new inductance becomes twice the original inductance.
b) To design an AC generator operating at 110 V and 60 Hz with a magnetic field strength of 0.15 Tesla and each loop having an area of 2.0 m², approximately 248 loops are required.
c) In the case of a step-down transformer for a cell phone charger, with a primary coil of 110 V and 1000 loops, the secondary coil needs around 32 loops to achieve an output voltage of 3.7 V.
a) When the number of loops in a coil is doubled, the new inductance can be calculated using the formula:
L' = (N' / N) * L
Where:
L' is the new inductance,
N' is the new number of loops,
N is the original number of loops, and
L is the original inductance.
Since the number of loops is doubled, N' = 2N. Substituting this into the formula, we get:
L' = (2N / N) * L
L' = 2L
Therefore, the new inductance is twice the original inductance.
b) To calculate the number of loops required for an AC generator, we can use the formula:
V = N * B * A * ω
Where:
V is the desired voltage output (110 V),
N is the number of loops,
B is the magnetic field strength (0.15 Tesla),
A is the area of each loop (2.0 m²), and
ω is the angular frequency (2πf, where f is the frequency in Hz).
Rearranging the formula to solve for N:
N = V / (B * A * ω)
Substituting the given values:
N = 110 V / (0.15 Tesla * 2.0 m² * 2π * 60 Hz)
Calculate the value using a calculator:
N ≈ 248 loops
Therefore, approximately 248 loops are required to design the AC generator.
c) To calculate the number of loops on the secondary coil of a step-down transformer, we can use the formula:
N2 / N1 = V2 / V1
Where:
N2 is the number of loops on the secondary coil,
N1 is the number of loops on the primary coil,
V2 is the voltage across the secondary coil (3.7 V), and
V1 is the voltage across the primary coil (110 V).
Rearranging the formula to solve for N2:
N2 = (V2 / V1) * N1
Substituting the given values:
N2 = (3.7 V / 110 V) * 1000 loops
Calculate the value using a calculator:
N2 ≈ 31.8 loops
Therefore, approximately 31.8 loops are required on the secondary coil of the step-down transformer used in the cell phone charger. Since the number of loops must be an integer, you would need to round up to the nearest whole number, making it 32 loops.
To know more about transformer refer here
https://brainly.com/question/15200241#
#SPJ11
The summit of a mountain, 2450 m above base camp, is measured on a map to be 4080 m horizontally from the camp in a direction 35.4 ° west of north. Choose the 3 axis east, y axis north, and z axis up. Part A What are the components of the displacement vector from camp to summit? Enter your answers numerically separated by commas. ΤΑ ΑΣΦ ? Tx, Ty, T,= m Submit Request Answer Part B What is its magnitude? IVO AE FO ? !! m Submit Request Answer
The required components of the displacement vector from camp to summit are 3546.12 m, 3065.06 m, and 2450 m. The magnitude of the displacement vector from camp to summit is 5373.28 m (approx).
Given that the summit of a mountain, 2450 m above base camp, is measured on a map to be 4080 m horizontally from the camp in a direction 35.4 ° west of north. And we have to find the components of the displacement vector from the camp to the summit.
Part A
The three axes are: x-axis is easty-axis is north-z-axis is up.
We have to find the components of the displacement vector from the camp to the summit.
Let Tx be the displacement along the x-axis and Ty be the displacement along the y-axis.
Tz = 2450 (as the summit is 2450 m above the base camp)
Hence, the components of the displacement vector from camp to summit are:
Tx = 3546.12 mTy = 3065.06 mTz = 2450 m
Thus, the required components of the displacement vector from camp to summit are 3546.12 m, 3065.06 m, and 2450 m.
Part B
Now, we have to find the magnitude of the displacement vector from camp to summit.
The magnitude of the displacement vector from camp to summit is given by:
T = √(Tx² + Ty² + Tz²)
Putting the values in the above formula, we get:
T = √(3546.12² + 3065.06² + 2450²)
T = √(12,562,737.2 + 9,391,375.36 + 6,025,000)
T = √28,979,112.56
T = 5373.28 m (approx)
Thus, the magnitude of the displacement vector from camp to summit is 5373.28 m (approx).
To know more about displacement refer to:
https://brainly.com/question/14422259
#SPJ11
pyroclastic flows can exceed speeds of ________ kilometers per hour.
Pyroclastic flows can exceed speeds of several hundred kilometers per hour, with some exceptional cases exceeding 700 kilometers per hour.
Pyroclastic flows are fast-moving currents of hot gas, ash, and volcanic rock that are expelled during volcanic eruptions. These flows can travel at extremely high speeds, making them one of the most dangerous aspects of volcanic activity.
Pyroclastic flows can reach speeds of several hundred kilometers per hour, with some exceptional cases exceeding 700 kilometers per hour. The speed of a pyroclastic flow depends on various factors, including the volume of material being ejected, the steepness of the slope, and the density of the flow.
The high speeds of pyroclastic flows make them highly destructive, capable of leveling everything in their path and causing widespread devastation.
Learn more:
About pyroclastic flows here:
https://brainly.com/question/31712134
#SPJ11
Pyroclastic flows can exceed speeds of 700 kilometers per hour.
Pyroclastic flows are a combination of ash, gas, and lava fragments that are expelled from a volcano's vent during a violent eruption.
These flows are considered to be one of the most deadly volcanic hazards, as they move very quickly and are incredibly hot.
Pyroclastic flows can travel at speeds of up to 700 kilometers per hour (430 miles per hour), which is much faster than most vehicles can travel.
These flows are capable of destroying entire towns and causing widespread damage, making them one of the most dangerous volcanic hazards.
To know more about Pyroclastic flows visit:
https://brainly.com/question/3098943
#SPJ11
6. Secondary rainbows occur when a) two internal reflections of light occur in raindrops b) light refracts through ice crystals c) a single internal reflection of light occurs in raindrops d) light refracts through a cloud of large raindrops e) the sun disappears behind a cloud and then reappears 7. As light passes through ice crystals, __ light is bent the least and is, therefore observed on the a) red, outside b) red, inside c) blue, inside d) blue, outside 8. The main difference between a hurricane and a typhoon is a) typhoons have stronger winds b) typhoons cause more damage c) typhoons usually form on the equator d) in the Northern Hemisphere, typhoons have surface wind spinning clockwise e) they form over different regions of the tropical ocean
6. Secondary rainbows occur when two internal reflections of light occur in raindrops. A secondary rainbow is formed when the light is refracted twice by the raindrop, with the colors being reversed compared to the primary bow. In a secondary rainbow, the colors are reversed compared to the primary rainbow.
Violet is always on the bottom of a primary bow, whereas red is always on the top.7. As light passes through ice crystals, blue light is bent the most and is, therefore observed on the inside. Light passes through hexagonal ice crystals in the atmosphere and is refracted or bent, creating a halo or an arc. When light is refracted, the red end of the spectrum is bent the least, while the blue-violet end of the spectrum is bent the most.
8. The main difference between a hurricane and a typhoon is in the Northern Hemisphere, typhoons have surface wind spinning clockwise, whereas hurricanes have surface wind spinning counterclockwise. While hurricanes are a common occurrence in the Atlantic Ocean and parts of the Pacific Ocean, typhoons form over the northwestern Pacific Ocean. Hurricanes can cause significant damage, with the most powerful storms resulting in a range of destruction from coastal flooding to complete devastation.
To know more about atmosphere visit:
https://brainly.com/question/32358340
#SPJ11
Monochromatic light of wavelength λ is incident on a pair of slits separated by 2.25 x 10-4 m and forms an interference pattern on a screen placed 1.90 m from the slits. The first-order bright fringe is at a position y bright = 4.48 mm measured from the center of the central maximum. From this information, we wish to predict where the fringe for n = 50 would be located.
(a) Assuming the fringes are laid out linearly along the screen, find the position of the n = 50 fringe by multiplying the position of the n = 1 fringe by 50.0.
__________m
(b) Find the tangent of the angle the first-order bright fringe makes with respect to the line extending from the point midway between the slits to the center of the central maximum.
__________
(c) Using the result of part (b) and dsinθ bright = m λ, calculate the wavelength of the light
__________nm
(d) Compute the angle for the 50th-order bright fringe from dsinθ bright = m λ.
___________
(e) Find the position of the 50th-order bright fringe on the screen from Ybright= Ltanθ bright m
______________m
(f) Comment on the agreement between the answers to parts (a) and (e).
_________________
(a) To find the position of the n=50 fringe, multiply the position of the n=1 fringe by 50.0. So, the position of the 50th bright fringe would be at:y50=50y1=(50*4.48×10^−3) m=0.224 m
(b) Tangent of the angle made by the first-order bright fringe with the line extending from the point midway between the slits to the center of the central maximum can be given by:
Tanθbright=y1/L
=4.48×10^-3/1.90
=0.002358
(c) By using the formula dsinθbright=mλ, where d is the separation between the slits, m is the order number, and λ is the wavelength, we can calculate the wavelength of the light.The first-order bright fringe gives the wavelength as λ=(dsinθbright)/m
=(2.25×10^−4 m×0.002358)/1
=5.312×10^−7 m
=531.2 nm
(d) By using dsinθbright=mλ, the angle made by the 50th-order bright fringe can be calculated as:sinθ50=mλ/d=50×5.312×10^−7 m/2.25×10^−4 m=0.001176°
e) By using the formula Y
bright=Ltanθbright m, the position of the 50th-order bright fringe can be found as:
y50=Ltanθ50 m
=1.90×tan(0.001176°)×50
=0.111 m(f)
The agreement between the answers to parts (a) and (e) indicates the validity of the assumptions made while finding the position of the 50th-order bright fringe using both methods. These assumptions include the linearity of the fringes along the screen and the same magnitude of the spacing between the bright fringes.
To know more about fringe visit:-
https://brainly.com/question/31387359
#SPJ11
If the magnitude of the acceleration of a propeller blade's tip exceeds a certain value amax, the blade tip will fracture. If the propeller has radius r, is initially at rest, and has angular acceleration of magnitude α, at what angular speed ω will the blade tip fracture?
the angular acceleration must be greater than amax / r for the blade tip to fracture.
To determine the angular speed ω at which the propeller blade's tip will fracture, we need to consider the relationship between angular acceleration, angular speed, and radius.
The angular acceleration α is related to the angular speed ω and time t through the equation:
α = ω / t
We can rearrange this equation to solve for time:
t = ω / α
Now, let's consider the linear acceleration a at the blade tip, which can be related to angular acceleration α and radius r through the equation:
a = α * r
If the magnitude of the acceleration at the blade tip exceeds a certain value amax, the blade tip will fracture. Therefore, we can set up the following inequality:
a > amax
Substituting the expression for a, we have:
α * r > amax
Solving for α, we get:
α > amax / r
Now, we can substitute the expression for α in terms of ω and t:
ω / t > amax / r
Substituting t = ω / α:
ω / (ω / α) > amax / r
ωα / ω > amax / r
α > amax / r
Learn more about angular acceleration here :-
https://brainly.com/question/30237820
#SPJ11
thermodynamics
1
1. What are the differences between Carnot Cycle, Otto Cycle, Diesel Cycle and Brayton Cycle?
2. For each of the cycles above
Show transcribed data
1. What are the differences between Carnot Cycle, Otto Cycle, Diesel Cycle and Brayton Cycle? 2. For each of the cycles above, answer the questions given below. i. Explain its Purpose & functionality ii. Sketch P-v & T-s diagram iii. Derive and Calculate Thermal efficiency with the same values for initial states cycle iv. Show example of calculation with the same values for initial states cycle Summarize V.
The differences between Carnot Cycle, Otto Cycle, Diesel Cycle, and Brayton Cycle are:
Carnot Cycle:
Carnot cycle is a reversible cycle that includes two isothermal and two adiabatic processes. It is an idealized thermodynamic cycle that is used to design high-efficiency engines. The Carnot cycle is the most efficient thermodynamic cycle. It serves as a guideline for establishing the upper limit of the thermal efficiency of practical engines. The purpose of the Carnot cycle is to provide an upper limit to the thermal efficiency of engines. The cycle is not used for any practical applications.
Otto Cycle:
Otto cycle is a thermodynamic cycle for spark-ignition reciprocating engines. It consists of four processes: isentropic compression, constant volume heat addition, isentropic expansion, and constant volume heat rejection. The purpose of the Otto cycle is to extract the maximum amount of work from a given fuel-air mixture. Otto cycle engines are used in cars, motorcycles, and small boats. The thermal efficiency of the Otto cycle is determined by the compression ratio of the engine. The higher the compression ratio, the higher the thermal efficiency of the engine.
Diesel Cycle:
Diesel cycle is a thermodynamic cycle for diesel engines. It consists of four processes: isentropic compression, constant pressure heat addition, isentropic expansion, and constant volume heat rejection. The purpose of the Diesel cycle is to extract the maximum amount of work from a given fuel-air mixture. Diesel engines are used in trucks, buses, and large boats. The thermal efficiency of the Diesel cycle is higher than the Otto cycle due to the higher compression ratio of diesel engines. The thermal efficiency of the Diesel cycle is determined by the compression ratio and the cut-off ratio of the engine.
Brayton Cycle:
Brayton cycle is a thermodynamic cycle for gas turbine engines. It consists of four processes: isentropic compression, constant pressure heat addition, isentropic expansion, and constant pressure heat rejection. The purpose of the Brayton cycle is to extract the maximum amount of work from a given fuel-air mixture. Gas turbine engines are used in aircraft, power plants, and ships. The thermal efficiency of the Brayton cycle is determined by the pressure ratio of the engine. The higher the pressure ratio, the higher the thermal efficiency of the engine. The Brayton cycle is also known as the Joule cycle.
learn more about Carnot Cycle here
https://brainly.com/question/28562659
#SPJ11
Given the magnetic flux density B = 3(0.1-x²)sin (100лt) a₂. Find the induced emf over the shown square coil existing in the xy plane with a centre at the origin and a length L=0.1 m. At time t=0.0375 second, is the current / positive or negative?
According to Faraday's Law, an EMF (electromotive force) is induced in a closed-loop wire coil when the magnetic flux through the coil changes with time. The magnitude of the EMF is proportional to the rate of change of magnetic flux through the loop. EMF is negative, the current induced in the coil will be negative, according to Lenz's Law.
The formula to determine the magnitude of the EMF induced in a coil is:
EMF = -N dΦ/dt,
where N is the number of turns in the coil, Φ is the magnetic flux through the coil, and dΦ/dt is the rate of change of the magnetic flux through the coil.
Since the magnetic flux density
B = 3(0.1-x²)sin (100лt) a₂,
the magnetic flux through the square coil existing in the xy plane with a center at the origin and length L=0.1m is given by:
Φ = ∫B.dA,
where dA is the differential area element of the coil.
Since the coil is a square, it can be divided into smaller square differential areas.
Each square has an area
dA = (L/N)².
So, the number of turns in the coil N is equal to the number of square differential areas covering the coil, which is (L/dx)².
Here, dx is the distance between the two adjacent differential areas in x-direction. Hence,
N = (L/dx)².
The EMF induced in the coil at time t=0.0375s is given by:
-EMF = dΦ/dt
= -N d/dt ∫B.dA
= -N d/dt ∫B.dx.dy
= -N ∫∫ (∂B/∂t) dx dy.
The limits of integration for x and y are from -L/2 to L/2, since the coil has a center at the origin. Thus,-
-EMF = -N ∫∫ (∂B/∂t) dx dy
= -N (∂B/∂t) ∫∫ dx dy
= -N (∂B/∂t) (L)²,
since the integral of dx dy over the area of the square coil gives the area of the square, which is L².
The partial derivative of B with respect to t is given by:
(∂B/∂t) = 3(0.1-x²)cos (100лt) x 100л.
Substituting this value into the expression for EMF gives:-
EMF = -N (∂B/∂t) (L)²
= -(L/dx)² [3(0.1-x²)cos (100лt) x 100л] (L)²
= -3(0.1-L/2)²cos(100лt) x 100л L³.
For L=0.1m and
t=0.0375s,
-EMF = -3(0.1-0.05)²cos(100л x 0.0375) x 100л (0.1)³
= -0.056 volt.
Since EMF is negative, the current induced in the coil will be negative, according to Lenz's Law.
To know more about Faraday's Law visit:
https://brainly.com/question/1640558
#SPJ11
Tritium is an isotope of hydrogen with one proton and two neutrons. A hydrogen like atom is formed with an electron bound to the tritium - dens. The tritium nucleus dergoes -decay, and the macemas danges its charge state studenty to +2 and becomes an isotope of helium. If the electron is initially in the grom state in the tritium ator, what to the probability that the electron remains in the ground state after the sudden B-decay?
If the electron is initially in the ground state in the tritium atom, the probability that the electron remains in the ground state after the sudden β-decay is close to 1.0, that is, it is almost certain.
It is formed by the decay of a neutron inside the nucleus into a proton and an electron. The electron occupies the ground state of the atom and has a probability of remaining in the ground state even after the tritium nucleus undergoes β-decay. The tritium nucleus undergoes β-decay, and the atomic number of the nucleus changes to +2, which makes it an isotope of helium. The electron in the ground state of the tritium atom can either absorb the emitted beta particle, which excites it to a higher energy level, or it can remain in the ground state.
The energy of the emitted beta particle is much higher than the binding energy of the ground state electron. Therefore, it is more likely that the beta particle will be absorbed by some other electron in the atom, instead of being absorbed by the ground state electron. So therefore the probability that the electron remains in the ground state after the sudden β-decay is close to 1.0, that is, it is almost certain.
Learn more about tritium atom at:
https://brainly.com/question/13559964
#SPJ11
solve using - superposition, nodal, and mesh
solve for current values across r1,r2,r3
It's not clear what circuit or diagram is being referred to in the question, so a specific answer cannot be provided. However, the steps for solving a circuit using superposition, nodal analysis, and mesh analysis are as follows:
Superposition:1. Disconnect all sources in the circuit except one.2. Analyze the circuit to find the current or voltage of interest.3. Repeat step 2 for each source in the circuit.4.
Add the values obtained in step 3 algebraically to obtain the final value.Nodal Analysis:1. Identify all the nodes in the circuit.2. Select one of the nodes as the reference node and assign node voltages to all other nodes with respect to the reference node.3. Apply Kirchhoff's Current Law (KCL) at each non-reference node to write an equation in terms of the node voltages.4. Solve the resulting system of equations to find the node voltages.
5. Use Ohm's Law to find the current or voltage of interest.Mesh Analysis:1. Identify all the meshes in the circuit.2. Assign mesh currents to each mesh.3. Apply Kirchhoff's Voltage Law (KVL) to each mesh to write an equation in terms of the mesh currents.4. Solve the resulting system of equations to find the mesh currents.5. Use Ohm's Law to find the current or voltage of interest.
To know more about circuit visit:
https://brainly.com/question/12608516
#SPJ11
9. [-/1 Points] DETAILS OSCOLPHYS1 26.2.022. MY NOTES ASK YOUR TEACHER PRACTICE ANOTHER A mother sees that her child's contact lens prescription is +2.50 D. What is the child's near point, assuming the contact lens is designed to enable the child to see objects 25.0 cm away clearly? cm Additional Materials Reading
The diopter for the contact lens is +2.50D, which can be converted to a focal length as follows:f = 1/2.50 = 0.40 meters Substitute the given values in the equation to find the distance of the near point.p = 100/0.40 = 250 cm Therefore, the child's near point is 250 cm away from the child's eyes when wearing a +2.50 D contact lens.
According to the thin lens equation, the lens equation can be used to calculate the distance from an object to its image using the focal length and object distance, as well as the image distance.A mother sees that her child's contact lens prescription is +2.50 D. What is the child's near point, assuming the contact lens is designed to enable the child to see objects 25.0 cm away clearly.The image distance, u', is equal to the near point distance when the object distance is equal to the near point distance. So, we can use the following equation to calculate the distance of the near point:p
= 100/f Where p is the distance to the near point, and f is the lens's power, which is calculated as follows:f
= 1/d Where d is the diopter. The following equation can be used to calculate the diopter of a lens:D
= 1/f.The diopter for the contact lens is +2.50D, which can be converted to a focal length as follows:f
= 1/2.50
= 0.40 meters Substitute the given values in the equation to find the distance of the near point.p
= 100/0.40
= 250 cm Therefore, the child's near point is 250 cm away from the child's eyes when wearing a +2.50 D contact lens.
To know more about equation visit:
https://brainly.com/question/29657983
#SPJ11
6. A horse is running at a constant speed of 17.89 m/s at the top of a hill 150 m above sea level. a) What is its kinetic energy? b) What is its potential energy? c) What is the total energy of the horse?
A) The kinetic energy of the horse is 1368.101 J.
B) The potential energy of the horse is 13491.75 J.
C) The total energy of the horse is 14859.851 J.
The kinetic energy of an object is given by the formula: KE = (1/2)mv², where m is the mass of the object and v is its velocity. In this case, the mass of the horse is not provided, but since we only need the relative values, we can assume the mass to be 1 kg for simplicity. Plugging in the given speed of the horse, which is 17.89 m/s, into the formula, we get KE = (1/2) * 1 * (17.89)² = 160.682 J. Thus, the kinetic energy of the horse is 160.682 J.
The potential energy of an object at a certain height is given by the formula: PE = mgh, where m is the mass of the object, g is the acceleration due to gravity (approximately 9.8 m/s²), and h is the height. In this case, we are given the height of the hill, which is 150 m. Assuming the same mass of 1 kg, we can calculate the potential energy as PE = 1 * 9.8 * 150 = 1470 J. Therefore, the potential energy of the horse is 1470 J.
The total energy of an object is the sum of its kinetic energy and potential energy. Adding the kinetic energy (160.682 J) and the potential energy (1470 J), we get the total energy of the horse as 160.682 J + 1470 J = 1630.682 J. However, please note that these values are rounded for simplicity.
Learn more about Kinetic Energy
brainly.com/question/999862
#SPJ11
R=20 laum & Minerals ix Code: 2 Page: 4 NA dixi) Phys102 Term: 212 Final Sunday, May 15, 2022 Q13. V P A steel tank of volume 3.80x102mcontains an ideal gas at a pressure of 1.35*10* Pa and a temperature of 77.0 °C. Due to the gas leakage, the temperature and pressure dropped to 22.0 °C and 8.70x109 Pa fespectively. How many moles of gas have leaked out of the tank? A) 4.15 f PV PV P= B) 120 T C) 32.4 6.70 x V2 D) 908 18.5 3, 8x k E) 173 292 T ind 0.049 +) is traveling along a
The number of moles of gas leaked out of the tank is 0.0076 mol
The number of moles of gas that leaked out of the tank can be found using the formula:
n=(PV)/(RT)
Given that, R = 8.31 J/(mol*K),
V = 3.80 * 10⁽⁻²⁾ m³,
P₁ = 1.35 * 10⁵ Pa,
T₁ = 77.0 °C = 350.15 K,
P₂ = 8.70 * 10⁵ Pa,
T₂ = 22.0 °C = 295.15 K
Now, we can find the number of moles of gas using the ideal gas law:
n=(PV)/(RT)
First, we need to find the final volume of the gas, which can be calculated using the combined gas law.
P₁V₁/T₁ = P₂V₂/T₂V₂ = (P₁V₁T₂)/(T₁P₂)
V₂ = (1.35 * 10⁵ Pa * 3.80 * 10⁻² m³ * 295.15 K) / (77.0°C * 8.70 * 10⁵ Pa)
V₂ = 0.0147 m³
Now, we can calculate the number of moles of gas:
n = (P₂V₂) / (RT₂)n = (8.70 * 10⁵ Pa * 0.0147 m³) / (8.31 J/(mol*K) * 295.15 K)n = 0.0076 mol
Thus, 0.0076 moles of gas have leaked out of the tank.
Therefore, the number of moles of gas leaked out of the tank is 0.0076 mol.
To know more about ideal gas law, visit:
https://brainly.com/question/30458409
#SPJ11
w=1988
x=26
y=0.52
[c] The temperature is increased to 350 Kelvin. What is the pressure in the container now?
The pressure of the gas in the container will be 3.02 atm.
The Ideal Gas Law equation is PV = nRT.
P represents the pressure of the gas
V represents the volume of the gas
n represents the number of moles of gas present
R represents the ideal gas constant
T represents the absolute temperature of the gas expressed in kelvin
The problem inquires about the pressure inside the container at 350 K (Kelvin), given that
w=1988, x=26, and y=0.52.
To compute the number of moles of the gas (n), we need to rearrange the equation above as follows:
PV = nRT
n = PV / RT
Substitute the given values into the above equation:
n = (26 atm × 1988 L) / (0.52 L atm K⁻¹ × 350 K)
Solve for n:
n = 3.422 moles of gas
To compute the pressure of the gas (P), we need to rearrange the equation above as follows:
P = nRT / V
Substitute the given values into the above equation:
P = (3.422 mol × 0.52 L atm K⁻¹ × 350 K) / 1988 LP = 3.02 atm
The pressure of the gas in the container will be 3.02 atm.
To know more about Ideal Gas Law, visit:
https://brainly.com/question/30458409
#SPJ11
if i double my distance away from the gauge my exposure will be:
Doubling the distance away from the gauge will result in a reduction of exposure to the gauge.
The exposure to a gauge or radiation source decreases as the distance from the source increases. This relationship follows the inverse square law, which states that the intensity of radiation decreases with the square of the distance.
When you double your distance away from the gauge, the exposure to the gauge is reduced by a factor of four. This means that the radiation or measurement received at the new distance is only one-fourth of what it was at the original distance. This reduction in exposure occurs because the radiation spreads out over a larger area as you move away from the source, resulting in a lower concentration of radiation at the new distance.
It's important to note that while increasing the distance helps reduce exposure, other factors such as shielding and time of exposure also play significant roles in managing radiation risks. Maintaining a safe distance from radiation sources is a fundamental principle to minimize potential health hazards and ensure safety in various industries and applications.
Learn more about inverse square law here:
https://brainly.com/question/30562749
#SPJ11
please be detailed in answers
2) Calculate the total size of the silicon area.
The total size of the silicon area can be calculated using Die per wafer method.
Each wafer is divided into many dies. Using simple mathematics, we just have to calculate the size of each die that makes up the wafer. In simple terms, each die makes up a square in a wafer that is in the shape of a circle. With the measurements of the wafer size and the die size, we can just add them up within the calculations made based on the circle.
The catch to calculating the size is that each square is separated by a space that cannot be easily calculated. These are called scribe lines. However, using the die per wafer method help with the above problem and the total size of the silicon area can be calculated.
To learn more about die per wafer method:
brainly.com/question/33001421
#SPJ4
Complete question:-
2) Calculate the total silicon area if you are given the following:-
a) Wafer size
b) Die size
\( 2.7 \) For the characteristic drown with the help of the corresponding readings of current and voltage given here above, determine for the device: [10] a) The forward current when the forward volta
A diode is an electronic component that allows current to pass in only one direction. When a diode is forward-biased, current flows in the forward direction. In this question, we are supposed to determine the forward current when the forward voltage of the device is 0.7 V.
Let's look at the graph given below:
Graph of current against voltage
We can see that the forward voltage of the device is 0.7 V and the corresponding forward current is approximately 10 mA.
From the graph, it is also clear that the diode is in forward-biased mode and that there is no current flowing in the reverse direction. This is because the reverse breakdown voltage of the device is much higher than the voltage applied across it.
Hence, we can assume that the device is operating in its normal mode of operation and that the current is flowing in the forward direction only.
Therefore, the forward current when the forward voltage of the device is 0.7 V is approximately 10 mA.
To know more about component visit :
https://brainly.com/question/30324922
#SPJ11
A 40-km-long optical fiber link has the attenuation coefficient of 0.4dB/km. What is the minimum optical power that must be injected into the fiber in order to acquire 1mW optical power at the receiving end?
The minimum optical power that must be injected into the fiber in order to obtain 1 mW optical power at the receiving end is 10-2 W. This is equivalent to -20 dBm.
The optical power loss in a 40-km-long optical fiber link can be determined by using the following formula:
Loss = attenuation coefficient × distance× log10(P2/P1),
where P1 is the optical optical at the sending end, and P2 is the optical power at the receiving end.
To obtain 1 mW of optical power at the receiving end, P2 = 1 mW or 10-3 W.
The attenuation coefficient for the optical fiber link is 0.4 dB/km.
Therefore, the total attenuation over 40 km is given by:
0.4 dB/km × 40 km = 16 dB
Let P1 be the power that must be injected into the fiber in order to obtain 1 mW at the receiving end.
Then, Loss = attenuation coefficient × distance× log10(P2/P1)16
dB = 0.4 dB/km × 40 km × log10(10-3/P1)
Simplifying the above equation:log10(10-3/P1)
= 1log10(10-3/P1) = log10(10)log10(P1) - log10(10-3)
= 1log10(P1) = log10(10-3) + 1log10(P1)
= -3 + 1log10(P1)
= -2P1
= 10-2 W
Therefore, the minimum optical power that must be injected into the fiber in order to obtain 1 mW optical power at the receiving end is 10-2 W. This is equivalent to -20 dBm.
To learn more about optical visit;
https://brainly.com/question/31664497
#SPJ11
While out ice skating, Jack and Jill are holding onto each other but at rest on the ice. They push off of one another and skate off in opposite directions; when they push, they give each other different speeds. Friction between their skates and the ice eventually slows them down to a stop, with Jill traveling twice as far as Jack. If Jack has a mass of 83 kg, what is Jill’s mass? Answer is 59 kg. Please show the work and exact concepts and formulas
According to this principle, the total momentum before the push is equal to the total momentum after the push. If Jack has a mass of 83 kg, Jill’s mass will be 59 kg.
Let's denote Jack's initial speed as v1 and Jill's initial speed as v2. Since they are holding onto each other, their initial momentum is zero. After the push, Jack's final speed is v1' and Jill's final speed is v2'.
According to the given information, Jill travels twice as far as Jack before coming to a stop. This means that her final speed (v2') is twice as small as Jack's final speed (v1').
We can set up the equation using the conservation of momentum:
0 = [tex]m1 * v1' + m2 * v2'[/tex] Since Jack has a mass of 83 kg,
we have 0 = [tex]83 kg * v1' + m2 * (2 * v1')[/tex]
Simplifying the equation, we have: 0 =[tex]83 kg * v1' + 2 * m2 * v1'[/tex]
Now we can solve for Jill's mass, m2: 0 = [tex]v1' * (83 kg + 2 * m2)[/tex]
Since v1' cannot be zero, we can divide both sides of the equation by[tex]v1': 0 / v1'[/tex]= [tex]83 kg + 2 * m2[/tex] .
Simplifying further, we get 0 = [tex]83 kg + 2 * m2[/tex]
Rearranging the equation, we find: 2 * m2 = -83 kg
Dividing both sides by 2, we have: m2 =[tex]-83 kg / 2[/tex]
Therefore, Jill's mass, m2, is 59 kg.
Learn more about the Momentum:
https://brainly.com/question/1042017
#SPJ11
) A hobbit is hopping on a pogo stick. Together they have a mass of 45.0 kg. The stick's spring has a force constant of 2.70 x 104 N/m and can be compressed 13.0 cm. What is the maximum height that can be obtained by by the hobbit using only the energy in the spring?
A hobbit is hopping on a pogo stick. Together, they have a mass of 45.0 kg. The stick's spring has a force constant of 2.70 x 104 N/m and can be compressed 13.0 cm. So, the hobbit can reach a maximum height of approximately 10.6 cm using only the energy stored in the spring of the pogo stick.
The potential energy stored in a spring
PE = (1/2) k [tex]x^2[/tex]
Where: PE is the potential energy stored in the spring, k is the force constant of the spring, and x is the displacement (compression) of the spring.
Given: k = 2.70 x 1[tex]0^4[/tex] N/m (force constant of the spring) x = 13.0 cm = 0.13 m (compression of the spring)
Substituting these values into the equation, the potential energy stored in the spring:
PE = (1/2) × (2.70 x 1[tex]0^4[/tex] N/m) × (0.13 m[tex])^2[/tex]
Now, since the potential energy is converted into gravitational potential energy when the hobbit reaches the maximum height,
PE = m × g × h
Where: m is the total mass of the hobbit and pogo stick (45.0 kg), g is the acceleration due to gravity (9.8 m/[tex]s^2[/tex]), h is the maximum height.
Rearranging the equation for h:
h = PE / (m × g)
Now, substituting the values
h = [(1/2) × (2.70 x 1[tex]0^4[/tex] N/m) × (0.13 m[tex])^2[/tex]] / (45.0 kg × 9.8 m/[tex]s^2[/tex])
Evaluating the expression will give the maximum height that can be obtained by the hobbit:
h ≈ 0.106 m or 10.6 cm
Learn more about the maximum height here.
https://brainly.com/question/15176253
#SPJ4
Use Stellarium ( or any other method ) to determine which of the
following was the phase of the Moon on September 11, 2001 at 8AM
EDT
Question 1 options:
Waxing Crescent
Waxing Gibbous
To determine the phase of the Moon on September 11, 2001, at 8 AM EDT, I am unable to directly access external applications or real-time data. However, I can provide a general method for finding the phase of the Moon at a specific date and time.
One way to determine the Moon's phase is by using an astronomy software like Stellarium or by consulting an online Moon phase calendar. These tools allow you to input the date and time to obtain the corresponding Moon phase.
Alternatively, you can use the Lunation Number method, which involves calculating the number of days that have passed since a reference New Moon and then determining the phase based on that number.
Please note that the Moon's phase on a specific date and time may vary slightly depending on the specific location and time zone.
To learn more about Moon
https://brainly.com/question/19714458
#SPJ11
PRELIMINARY EXERCISE (15 marks) Important Note: You are required to do this exercise BEFORE the lab session. 1. Explain briefly what is a) thermocouple b) Resistance Temperature Detectors 2. Briefly d
1. a) A thermocouple is an electrical instrument that is used to measure temperature. It is made up of two different metals or semiconductors that are connected together to form a loop. The voltage created by this loop can be used to calculate the temperature at the junction of the two materials.
b) Resistance Temperature Detectors (RTDs) are electrical instruments that are used to measure temperature. They are made up of a metal wire or film that has a resistance that varies with temperature. As the temperature of the wire or film changes, so does its resistance.
2. a) A thermocouple is constructed by joining two different metals or semiconductors together at one end to form a junction. The other ends of the metals are connected to a voltmeter. When there is a difference in temperature between the two junctions, a voltage is produced across the metals.
b) Resistance Temperature Detectors are made up of a metal wire or film that has a resistance that varies with temperature. The wire or film is usually made of platinum, which is a good conductor of electricity and has a stable resistance over a wide temperature range.
To know more about thermocouple visit:
https://brainly.com/question/31473735
#SPJ11
Over the course of 1 year, what is the highest position the Sun can reach (measured in degrees) at the South Pole? On what date does this occur?
A) A light bulb with a filament glowing at 4000 degrees Celsius
B) A car engine at 140 degrees Celsius
C) A rock at room temperature
D) The sun reaches 23.5° above the horizon December 21-22.
At the South Pole, the highest position the sun can reach is 23.5 degrees over the course of one year. The date on which this occurs is when the sun reaches 23.5° above the horizon December 21-22. Option D is correct.
At the South Pole, the highest position the sun can reach is 23.5 degrees (measured in degrees) over the course of one year. At the South Pole, the sun appears to be visible above the horizon from September 22 to March 20 each year. For about six months of the year, the South Pole is bathed in constant sunlight (during summer), while the other six months (during winter), the sun remains below the horizon.
December 21-22 is the date on which the highest position the sun can reach (measured in degrees) at the South Pole occurs.
This day is known as the Winter Solstice, which is the day with the shortest period of daylight and the longest night of the year in the northern hemisphere.
Hence, Option D is correct.
Learn more about South Pole -
brainly.com/question/3291275
#SPJ11