A small glass bead has been charged 3 60nCA small metal ball bearing 2.60 cm above the bead feels a 1.8 * 10 2 * N downward electric force

The new acceleration of the object is therefore a' = a / 2.91 = 25.3 m/s/s / 2.91 = 8.69 m/s/s to 3 significant figures.

We know that the force exerted on an object is equal to its mass times its acceleration, or F = m * a. If the force exerted on the object remains constant, then the new acceleration of the object after its mass has been increased by a factor of 2.91 can be calculated as follows:

a' = F / (m * 2.91) = F / m'

Where m' is the new mass of the object.

Substituting the original acceleration and mass into the equation, we get:

a' = F / (m * 2.91) = F / (m * 2.91) = (m * a) / (m * 2.91) = a / 2.91

The new acceleration of the object is therefore a' = a / 2.91 = 25.3 m/s/s / 2.91 = 8.69 m/s/s to 3 significant figures.

learn more about acceleration: https://brainly.com/question/460763

#SPJ1

A heart defibrillator being used on a patient has an RC time constant of 23.0 ms. ,If the defibrillator has a 9.75 μF capacitance, then it takes approximately 21.1 ms for the initial voltage of 12.0 kV to decline to 115 v.

The calculation is explained below,

RC = resistance x capacitance

resistance = RC / capacitance

resistance = (23.0 ms) / (9.75 μF) = 2,359 ohms

Time for  the initial voltage of 12.0 kV to decline to 115 V,

V(t) = V₀ ×  [tex]{e}^(^-^t^/^R^C^)[/tex]    ( here, V(t)=voltage at time t, V₀= initial voltage, e= constant= 2.71828, t= time, R= resistance, C= capacitance)

For t= -RC × ln(V(t) / V₀)

t = - (23.0 ms) × ln(115 V / 12.0 kV) = 21.1 ms

Hence, a heart defibrillator being used on a patient has an RC time constant of 23.0 ms. ,If the defibrillator has a 9.75 μF capacitance, then it takes approximately 21.1 ms for the initial voltage of 12.0 kV to decline to 115 v.

Learn more about the voltage of defibrillator here.

https://brainly.com/question/14799828

#SPJ9

Answer: B is right

Explanation:  Change in Momentum / Time Therefore, the force experienced by the ball is: Force = 1.52 kg·m/s / 0.0105 s Force = 144.76 N Answer: B. 144.76 N

[tex]{ \qquad\qquad\huge\underline{{\sf Answer}}} [/tex]

As the boy moves the bar magnet towards the magnetic compass, the needly is pulled slightly towards the bar magnet, so if he deduct the separation to 8 cm, most probably the needle would be pulled more towards the bar magnet.

Hence, the correct choice will be : (c)

Answer: c I think

Explanation I think its c

Answer: So, the average distance from the Sun of a planetary object with an orbital period of 325 years is approximately 40.0 AU.

Explanation:

The average distance from the Sun (in astronomical units) of a planetary object with an orbital period of 325 years can be estimated using Kepler's Third Law of Planetary Motion. This law states that the square of the orbital period (T) of a planet is proportional to the cube of its average distance from the Sun (r):

T^2 = k * r^3

where k is a constant. We can rearrange this equation to solve for r:

r = (T^2 / k)^(1/3)

The value of k depends on the units used for T and r, so it is important to make sure that the units are consistent. If T is in years and r is in astronomical units (AU), then k has a value of approximately 4π^2.

Using this formula, we can estimate the average distance from the Sun of a planetary object with an orbital period of 325 years:

r = (325^2 / (4 * π^2))^(1/3)

r ≈ 40.0 AU

So, the average distance from the Sun of a planetary object with an orbital period of 325 years is approximately 40.0 AU.

Drag the phase slider left and right to move the planet into and out of transit mode. The normalized flux (the relative amount of starlight reaching an observer on Earth) when the planet is off the side (not transiting) is 0.990 while the normalized flux when the planet is transiting is 1.000. Thus, the correct option for this question is B.

Normalized flux may be characterized as a type of key methodology in spectral data mining. It is important for the efficiency and accuracy of the automatic processing of massive astronomical spectral data, information extraction, and sharing.

A transit occurs when a planet passes between a star and its observer. Transits within our solar system can be observed from Earth when Venus or Mercury travel. The frequency of the normalized flux when the planet is transiting is completely different from when the planet is off the side.

Therefore, the correct option for this question is B.

To learn more about the Phase slider, refer to the link:

https://brainly.com/question/16552168

#SPJ1

Answer: 1.000,0.990 (correct)

Explanation:

To solve for the potential energy at points A and D, we need to use the formula for gravitational potential energy:

[tex]PE = mgh[/tex]

At point A, the height is h = 100 m and the mass of the cart is m = 250 kg. The acceleration due to gravity is g = 9.81 m/s^2. Therefore, the potential energy at point A is:

[tex]PE_A = mgh = (250 kg)(9.81 m/s^2)(100 m) = 245250 J[/tex]

At point D, the height is h = 75 m and the mass of the cart is still m = 250 kg. The potential energy at point D is:

[tex]PE_D = mgh = (250 kg)(9.81 m/s^2)(75 m) = 183937.5 J[/tex]

To solve for the velocity at point D, we can use the conservation of energy principle. At point A, the cart has only potential energy (no kinetic energy), so the total mechanical energy is equal to the potential energy:

[tex]E_A = PE_A = 245250 J[/tex]

At point D, the cart has both potential energy and kinetic energy. Therefore, the total mechanical energy is the sum of the potential and kinetic energies:

[tex]E_D = PE_D + KE_D[/tex]

where [tex]KE_D[/tex] is the kinetic energy at point D, and it is what we want to find.

According to the conservation of energy principle, the total mechanical energy at point D must be equal to the total mechanical energy at point A (assuming no non-conservative forces such as friction act on the cart between A and D). Therefore:

[tex]E_A = E_D[/tex]

Substituting in the values we have calculated:

[tex]245250 J = 183937.5 J + KE_D[/tex]

Solving for [tex]KE_D[/tex], we get:

[tex]KE_D = 61212.5 J[/tex]

To find the velocity at point D, we can use the formula for kinetic energy:

[tex]KE = (1/2)mv^2[/tex]

where KE is the kinetic energy, m is the mass of the object, and v is the velocity of the object.

Substituting in the values we have calculated, we get:

[tex]KE_D = (1/2)mv_D^2Solving for v_D, we get:v_D = sqrt((2KE_D) / m) = sqrt((2(61212.5 J)) / (250 kg)) = 17.6 m/s[/tex]

Therefore, the velocity at point D is 17.6 m/s.

Learn more about potential energy, here:

https://brainly.com/question/24284560

#SPJ9

Answer: Warm

Explanation:

In the physical activity pyramid, sedentary activities belong to Level D.

The Physical Activity Pyramid is a graphic representation of the different types of physical activities that are recommended for a healthy lifestyle.

The pyramid is divided into four levels, with the most important activities at the bottom and the least important at the top. The greatest and most significant activities for healthy everyday life are at the bottom and the least healthy activities at the top, which you should only perform occasionally.

Sedentary activities, which are activities that involve little or no physical movement, belong at the top of the pyramid, in Level D.

Level D is the smallest section of the pyramid, and it represents activities that should be limited in order to maintain good health.

Hence, option D is the correct choice.

For a similar question on the Physical Activity Pyramid,

https://brainly.com/question/18893749

#SPJ4

If one's primary goal is to build strength and increase muscle mass, completing workout sets of high repetitions and low weight is correct that is the last option, as the aerobic activity would not increase the muscle.

Anaerobic activities should be prioritized because they force the muscles to work at high intensity for short periods of time; this type of training is typically done with heavy weights for fewer repetitions and sets and builds the muscles.

Hence, if one's primary goal is to build strength and increase muscle mass, completing workout sets of high repetitions and low weight is correct that is the last option, as the aerobic activity would not increase the muscle.

Learn more about the muscle-building exercise here.

https://brainly.com/question/7991599

#SPJ1

Any moving object has momentum. The momentum of an 11 kg bowling ball rolling at 4 m/s is 44 kg m/s.

The momentum is defined as a quantity which is the product of the mass of the particles and its velocity. It is a vector quantity. It has both magnitude and direction. The rate of change of momentum is equal to the force acting on the particle.

The equation of the momentum is given as:

p = mν

= 11 kg × 4 m/s

= 44 kg m/s

Thus the momentum of the bowling ball is 44 kg m/s.

To know more about momentum, visit;

https://brainly.com/question/29598011

#SPJ9

Answer:

Explanation:

Here is a step by step explanation of how to solve the problem:

Break the initial velocity into x and y components. The velocity of the Pokéball can be broken down into two components: the horizontal component (vix) and the vertical component (viy). The horizontal component remains constant throughout the motion and has a value of vix = vcosθ, where v is the magnitude of the velocity and θ is the angle of launch. The vertical component changes due to the acceleration of gravity and has a value of viy = vsinθ - gt, where t is time.

Solve for the time of flight. We want to find the time it takes for the Pokéball to reach its maximum height, so we need to set viy = 0 and solve for t:

0 = vsinθ - gt

gt = vsinθ

t = vsinθ / g

Calculate the maximum height. The maximum height is reached when the vertical component of velocity is equal to zero, so we can use the equation:

h = viy^2 / (2g)

h = (vsinθ)^2 / (2g)

Calculate the range. The range is the horizontal distance traveled by the Pokéball during its flight, and it can be found using the equation:

x = vix * t

x = vcosθ * (vsinθ / g)

Draw a well labeled diagram of the physical situation. Draw the coordinate axes, showing the directions, and label the initial velocity as a vector. Show the trajectory of the Pokéball, including the point where it reaches its maximum height, and label the acceleration due to gravity.

The mass of the truck decreases while the velocity of the truck increases.  Option B

A closed system is a system in which matter cannot enter or leave the system, but energy can be exchanged between the system and its surroundings. In other words, a closed system is isolated from its environment in terms of mass, but not in terms of energy.

Closed systems can be found in many different areas of science and engineering, including thermodynamics, mechanics, and engineering. For example, in thermodynamics, a closed system is a system in which heat can be transferred between the system and its surroundings, but no mass can be transferred. In mechanics, a closed system is a system in which the total momentum of the system remains constant, regardless of any external forces acting on the system.

Learn more about closed system:https://brainly.com/question/14782983

#SPJ1

The change in velocity of the turtle from 1 mm/s at angle 0° to motion at a velocity of 1.2 mm/s at an angle 20° is -0.51 mm/s.

Velocity ​​is defined as the directional motion of an object, as indicated by the rate of change of position as observed from a particular frame of reference and measured by a particular standard of time.

Velocity is the vector quantity as it has both magnitude as well as direction. It is expressed as

Velocity= Displacement/ Time Taken

It's SI unit is meter/second. Other units commonly used are ft./s, miles per hour km/h etc.

Here, initial velocity of turtle = 1 mm/s at  0°

u = u cosθ = 1 mm/s cos 0 = 1 mm/s

final velocity = v cos 20 = 1.2 m/s cos 20 = 0.48 mm/s.

then, change in velocity = 0.48 mm/s - 1 mm/s = - 0.51 mm/s.

Therefore, the change in velocity of the turtle is - 0.51 mm/s.

Learn more about Velocity, here:

brainly.com/question/18084516

#SPJ1

The tension force T1 in the horizontal direction is mg sinθ, for the angle of zero, the tension force becomes zero. The tension force T2 is mgcosθ, for an angle of 30.1 the force is 63 N.

Tension force is a kind of force acting on object if it experience a force from a suspended mass on it. It is a vector quantity and having both direction and magnitude.

The horizontal tension force = mg sin θ

and the vertical or diagonal tension = mg cos θ

given mass suspended m = 25.5 kg.

Then, horizontal tension force T1 = 25.5 kg ×9.8 m/s²× sin 0 = 0

(sin 0 = 0)

The tension force T2 = mg cos θ

T2 = 25.5 kg ×9.8 m/s²× cos 30.1 = 63 N.

Therefore, tension force on cable 1 is zero and that on cable 2 is 63 N.

Find more on tension force:

https://brainly.com/question/30033702

#SPJ1

The magnitude of the electric field in the region r≤a is zero.

What is Point Charge?

A point charge is a theoretical charge that is assumed to be located at a single point in space, with all of its electric charge concentrated at that point. It is an idealized model that is often used to simplify calculations in electromagnetism. A point charge can be either positive or negative and is characterized by its electric charge, which is a fundamental property of matter. The electric field created by a point charge decreases with distance from the charge, following an inverse square law. The concept of a point charge is often used in electrostatics, where the charge distribution of an object can be approximated as a collection of point charges.

Inside the hollow metal sphere (i.e., for r≤a), the electric field is zero because the excess charge +2Q on the sphere redistributes itself to cancel out the electric field due to the central charge +Q.

This can be shown using Gauss's Law. A spherical Gaussian surface of radius r≤a, centered at the center of the sphere and inside the metal shell, encloses only the point charge +Q. By symmetry, the electric field is radial and has the same magnitude at every point on the Gaussian surface. By Gauss's Law, the total electric flux through the surface is proportional to the charge enclosed by the surface. Since there is no charge inside the surface (because the excess charge on the metal sphere cancels out the charge inside it), the total electric flux through the surface is zero. Therefore, the electric field inside the hollow metal sphere is zero.

Thus, the magnitude of the electric field in the region r≤a is zero.

Learn more about Point Charge from given link

https://brainly.com/question/25923373

#SPJ1

However, typically, electrical codes require that buried secondary service conduits be installed at a minimum depth of 18 inches (45.7 cm) below the surface. In some cases, local codes may require a deeper depth, such as 24 inches (60.9 cm) or more, depending on factors such as soil type, climate, and intended use of the conduit.

It is also important to note that other factors, such as the type and size of conduit, the type of wiring used, and the intended electrical load, may also affect the required burial depth. Therefore, it is essential to consult with local building codes and a licensed electrician or electrical engineer to determine the appropriate depth for installing external underground secondary service conduits.

To know more about Electrical codes, here

https://brainly.com/question/17215290

#SPJ4

Answer:

A

Explanation:

The final velocity of the truck can be calculated using the law of conservation of momentum. The law states that the total momentum of a closed system (the car and truck) remains constant unless an external force acts on the system.

Let's call the final velocity of the system (car + truck) after the collision vf.

The initial momentum of the car before the collision is equal to m1 * v1 = 1500 kg * 20 m/s = 30000 kg m/s, where m1 is the mass of the car and v1 is its initial velocity.

The initial momentum of the truck before the collision is equal to m2 * v2 = 2500 kg * -30 m/s = -75000 kg m/s, where m2 is the mass of the truck and v2 is its initial velocity.

The total initial momentum of the system before the collision is equal to the sum of the initial momenta of the car and truck:

p_initial = m1 * v1 + m2 * v2 = 30000 kg m/s + (-75000 kg m/s) = -45000 kg m/s.

After the collision, the final momentum of the system is equal to the sum of the final momenta of the car and truck:

p_final = m1 * vf + m2 * vf = (1500 kg + 2500 kg) * vf = 4000 kg * vf.

Since the total momentum of the system is conserved, we can set the initial and final momenta equal to each other:

-45000 kg m/s = 4000 kg * vf

Finally, we can solve for the final velocity of the system (truck):

vf = -45000 kg m/s / 4000 kg = -11.25 m/s

Since the truck was moving west before the collision, the final velocity is 11.25 m/s west, so the answer is A. 11.25 m/s west.

The capacitance of the second capacitor is 5.1 microfarads.

Capacitance is the ability of an electrical component, such as a capacitor, to store an electrical charge. The amount of charge that can be stored is related to the capacitance, which is measured in Farads. The larger the capacitance, the more charge a capacitor can store.

The total capacitance of two capacitors connected in parallel is equal to the sum of the individual capacitances. That is, C_total = C1 + C2.
We know the value of one of the capacitors, C1, to be 50 microfarads, and we know the current through it, I1, to be 2.34 A.
Since capacitance and current are inversely proportional, we can use this relationship to solve for the capacitance of the second capacitor, C2.
C2 = C1 * (I2 / I1)
where I2 is the current through the second capacitor, which we know to be 0.40 A.
Plugging in the values, we get:
C2 = 50 * (0.4 / 2.34)
C2 = 5.1 microfarads
Therefore, the capacitance of the second capacitor is 5.1 microfarads.

To learn more about capacitance
https://brainly.com/question/27258294
#SPJ1

The three phases of bromine are: liquid, gas, and solid. To order these phases based on the distance between bromine particles, from least to greatest.

We need to consider how the intermolecular forces change as the temperature and pressure change.

In the solid phase, bromine molecules are packed tightly together, with the minimum distance between particles. This is because the intermolecular forces, including London dispersion forces and dipole-dipole forces, are strong enough to hold the particles in a fixed position.

In the liquid phase, the bromine molecules are further apart than in the solid phase, but still close enough to experience intermolecular forces. The temperature of the liquid is high enough to overcome the attractive forces and cause the particles to move about more freely, but not enough to separate the particles completely.

In the gas phase, the bromine molecules are separated by the greatest distance, with no strong intermolecular forces to hold them in place. The high temperature of the gas causes the particles to move rapidly, colliding with each other but not sticking together.

Therefore, the order of the three phases based on the distance between bromine particles is solid < liquid < gas.

To know more about bromine please refer: https://brainly.com/question/29028678

#SPJ4

Answer:

Explanation:

When the hammer hits the nail it transfers this energy to the nail in order to move it 1cm (0.01m). A transfer of energy is known as "work done" and work done = force x distance. So, force = work done / distance = 25 / 0.01 = 2500N Answer: Average force = 2500 Newtons.

The acceleration of the car is  2.5 m/s² to the right.

The acceleration of the car is calculated by applying Newton's second law of motion as shown below.

F  (net ) = ma

F - Ff = ma

where;

3400 N - 400 N = 1200a

3000 = 1200a

a = 3000 / 1200

a = 2.5 m/s² to the right

Learn more about acceleration here: https://brainly.com/question/14344386

#SPJ1

Answer:

Explanation:

A elastic

Answer:

Newtons

Explanation:

The acceleration of the bicyclist is a[tex](8x)/(4t) = 2x/3t^2.[/tex]

Acceleration is a measure of the rate of change of an object's velocity over a period of time. It is a vector quantity, meaning it has both a magnitude (or size) and a direction. Acceleration can be positive, negative, or zero. A positive acceleration is when a body is speeding up, a negative acceleration is when a body is slowing down, and a zero acceleration is when a body's velocity is constant.

The bicyclist's acceleration can be determined by noting the displacement (x) and the time (t) required to cover that displacement.

The equation for acceleration is a = (change in velocity)/(change in time). In this case, the change in velocity is 8x and the change in time is 4t. Therefore, the acceleration of the bicyclist is a =[tex](8x)/(4t) = 2x/3t^2.[/tex]

To learn more about acceleration visit

brainly.com/question/605631

#SPJ1

Answer: B is correct

Explanation: The mass of the car can be calculated using the equation: mass = momentum / velocity Therefore, the mass of the car is: mass = 15,000 kg*m/s / 35 m/s mass = 428.6 kg

The third rule of a series circuit states that the sum of the individual voltages equals the total voltage.

These demonstrate the truth of the previous claim, which reads, "When voltage sources are connected in series, the overall voltage is equal to the algebraic sum of the individual voltages?"

The supply voltage is equal to the total of the component voltages in a series circuit. The voltages across each component in a series circuit are proportional to their resistances. This means that when two similar components are linked in series, the supply voltage is divided equally.

To learn more about voltage visit;

https://brainly.com/question/29445057

#SPJ4

The man has at most 3.55 s to get out of the way.

Kinematics can be defined as a subfield of physics developed in classical mechanics that describes the motion of points, bodies and systems of bodies without considering the forces that cause them to move.

We can solve this problem using kinematic equations.

First, we can find the time it takes for the block to fall from a height of 84.9 m using the formula:

y = 1/2 * g * t^2

where

Rearranging this equation, we get:

t = sqrt(2y/g) = sqrt(2 * 84.9 m / 9.81 m/s^2) = 4.09 s (to two significant figures)

So the block will hit the ground after 4.09 s of falling.

Next, we can find the time it takes for the block to fall from a height of 16.6 m using the same formula:

t = sqrt(2y/g) = sqrt(2 * 16.6 m / 9.81 m/s^2) = 1.41 s (to two significant figures)

So the block will take 1.41 s to fall from a height of 16.6 m to the ground.

The man has to get out of the way before the block falls the remaining distance of (84.9 - 16.6) = 68.3 m. We can find the time it takes for the block to fall this distance using the same formula:

t = sqrt(2y/g) = sqrt(2 * 68.3 m / 9.81 m/s^2) = 3.55 s (to two significant figures)

Therefore, the man has at most 3.55 s to get out of the way.

Learn more about kinematic equations here : brainly.com/question/28788270

#SPJ1

The Compton effect can be explained on the basis of the quantum theory of light and the wave theory of scattered radiation, hence option B is correct.

The compton effect, photoelectric effect, and blackbody radiation are described by the quantum theory of light, while interference and diffraction are explained by the wave nature of light.

It causes X-rays and other powerful electromagnetic radiations to have longer wavelengths after being elastically dispersed by electrons.

Therefore, the compton effect, also known as Compton scattering, is the primary mechanism by which radiant energy is absorbed in the matter.

Learn more about the compton effect, here:

https://brainly.com/question/10581731

#SPJ9

The given question is incomplete, so the most probable complete question is,

Can someone answer this question about the Compton effect?

The Compton effect can be explained on the basis of __________

a) Wave nature of light

b) Quantum theory of light

c) Ray optics

d) Wave optics

Answer:

Explanation:

Because the scientists still had seeds from the pre-drought mustard plants collected in 1997, they were in a perfect position to find out whether the change in flowering time was really due to evolution. They grew pre-drought seeds alongside seeds collected from the exact same sites in 2004, after the drought.

There are many ways that scientists could have discovered that the flowering time of the field mustard had changed. One possible way is through direct observation and monitoring of the plant's growth and development over time. Another possible way is through the analysis of historical records or herbarium specimens.

Mustard is a plant species that belongs to the Brassicaceae family, which also includes other common plants such as broccoli, cabbage, and cauliflower. The mustard plant is characterized by its small yellow flowers, which grow on a tall stem with leaves that are either lobed or unlobed.

Mustard has been cultivated for centuries for its seeds, which are used to produce mustard condiments, as well as for its leaves, which are used in salads and as a cooked vegetable. There are several different varieties of mustard, including white mustard (Sinapis alba), brown mustard (Brassica juncea), and black mustard (Brassica nigra).

Flowering timing refers to the time when a plant produces flowers, which is an important aspect of its life cycle. The timing of flowering can be influenced by several factors, including environmental conditions such as temperature, light, and water availability, as well as genetic factors.

Flowering timing is important for plant reproduction, as it determines when the plant will produce seeds. In many plant species, the timing of flowering is also influenced by environmental cues such as day length, which can trigger the plant to flower at specific times of the year.

Understanding flowering timing in plants is important for agriculture, as it can help farmers optimize crop yields by selecting the right varieties of plants for specific growing conditions and by manipulating environmental factors to promote optimal flowering. It is also an important area of research in plant biology, as scientists seek to understand the genetic and molecular mechanisms that control flowering timing in different plant species.

Here in the question,

There are several ways that scientists could have discovered that the flowering time of the field mustard had changed. One possible way is through direct observation and monitoring of the plant's growth and development over time.

For example, scientists may have regularly visited a field of mustard plants and recorded the timing of flowering for several years. By comparing the data from different years, they could have detected changes in the flowering time of the plants.

Another possible way is through the analysis of historical records or herbarium specimens. Herbarium specimens are dried and pressed plants that are stored in a collection for scientific study. By examining herbarium specimens collected from the same location over time, scientists could determine whether there had been any changes in the timing of flowering.

Additionally, researchers may have used satellite imagery to track changes in vegetation over time. By analyzing changes in the color and density of vegetation in a particular area, they could detect changes in the timing of flowering for different plant species, including field mustard.

Therefore, there are many different methods that scientists could have used to discover changes in the flowering time of field mustard, and it is likely that a combination of these methods was used to confirm the change.

To know more about global warming click:

https://brainly.com/question/29625243

#SPJ2