The solenoid's inductance and the average emf around the solenoid if the current changes from +3.50 A to −3.50 A in 7.83 ✕ 10−3 s will be 1.01 ×10⁻⁸ H and 9.02 × 10⁻² V.
What is a solenoid?A coil of wire that carries an electric current is a solenoid. A solenoid is an electromagnet formed by a helical coil of wire.
Which generates a magnetic field when an electric current is passed through the coil.
A solenoid is a form of coil that produces a magnetic field when the electric current is passed through it. A solenoid is created when a conductive wire is used to make a loop.
Given data;
Turns ,N = 465
Length,L= 8.00 cm
Cross-sectional area,A = 3.10 ✕ 10−9 m2.
Solenoid's inductance, L=?
The average emf around the solenoid, E=?
Time of flow,t= 7.83 ✕ 10−3 s
Current changes from +3.50 A to −3.50 A
The inductance of the solenoid is found as;
[tex]\rm L = \frac{\mu_0 AN^2}{L} \\\\ \rm L = \frac{4 \times \pi \times 10^{-7}\times 3.0 \times 10^{-9} \times (465)^2 }{8.00 \times 10^{-2}} \\\\ L= 1.01 \times 10^{-8} \ H[/tex]
The average emf around the solenoid is found as;
[tex]\rm e = L \frac{I_2-I_1}{t} \\\\ \rm e = 1.01 \times 10^{-8} \times \frac{3.50-(-3.50)}{7.83 \times 10^{-3}} \\\\ e =9.02 \times 10^{-12} \ V[/tex]
Hence, the solenoid's inductance will be 1.01× 10⁻⁸ H.
To learn more about the solenoid refer;
https://brainly.com/question/16015159
#SPJ1
Question 3 of 15
Which statement describes an advantage of using nuclear fission to produce
electricity?
A. It uses a fuel made of atoms with large nuclei that will be
destroyed.
B. It is much more efficient than any other process used to generate
power.
C. It happens in large buildings that are expensive to build.
D. It produces radioactive waste products that must be stored safely.
Answer:
it is much more efficient than any other process to generate power
an ac voltage of 12.0 v is applied to the primary transformer that has 3 times as many turns in the secondary than in the primary. what is the voltage of the secondary?
The voltage of the secondary will be 36 V.From the given conditions primary transformer has 3 times as many turns in the secondary coil.
What is induced voltage?Electromagnetic induction is what causes the induced voltage. Electromagnetic induction is the process of generating emf (induced voltage) by subjecting a conductor to a magnetic field.
In this case, a magnet is pushed in and out of a wire coil attached to a high-resistance voltmeter.
Typically, a transformer's primary winding is attached to the input voltage source and changes electrical power into a magnetic field.
The secondary winding's role is to turn this alternating magnetic field into electricity, generating the necessary output voltage.
Given data;
Primary coil voltage,[tex]\rm V_P = 12 \ v[/tex]
Secondary coil voltage,[tex]\rm V_s = ?[/tex]
No turns in the primary coil,[tex]\rm N_p[/tex]
No turns in the secondary coil,[tex]\rm N_s[/tex]
From the given condition;
[tex]\rm N_s = 3N_p[/tex]
For a transformer,
[tex]\rm \frac{V_p}{V_s}= \frac{N_p}{N_s} \\\\ \rm \frac{12}{V_s}= \frac{N_p.}{3N_p} \\\\ V_s = 36 \ V[/tex]
Hence the voltage of the secondary will be 36 V.
To learn more about the induced voltage refer to the link;
https://brainly.com/question/19482771
#SPJ1
A periodic wave has a wavelength of 0,50 m and a speed of 20 m/s, What is the wave frequency?
Answer:
u=speed, w=wavelenght, f=frequency
It's known that u=w*f => f=u/w
u=20m/s ==> f=20/0,5 => f=40 Hz
w=0,50m
Explanation:
differentiate e^x - 8x +7
please answer the questions asap
Answer:
eˣ-8.
Explanation:
(eˣ-8x+7)'=eˣ-8.
A satellite completes one revolution of a planet in almost exactly one hour. At the end of one hour, the satellite has traveled 2.0 × 107 meters and is only 10 meters away from its starting point. What is the numerical value of the satellite's average velocity after that one hour?
Answer:
shown below
Explanation:
2 x 10⁷ as a number is 20,000,000
20,000,000 - 10 = 19,999,990
It went 19,999,990 m/h
in km/h:
19,999,990 / 1000 = 19,999.99 km/h
in km/s
19,999,990 / 3,600,000 = ~5.56 km/s
in m/s
19,999,990 / 3600 = ~5555.56 m/s
PLEASE ANSWER THIS FAST
The electric field lines show the way (blank) charges would move if they were in the field brainly.
Answer:
Explanation:
If a positive charge is moving in the direction of electric field vector, its velocity will increase, whereas positive charge moving opposite to the direction of the electric of electric field will decelerate.
The case with a negative charge is just reversed verse, it will decelerate when moving along the field direction and accelerate when moving opposite to it.
Help with this :
What device does not store electric current or charge?
a) Capacitor
b) Transforme
c) vacuum tube
I know a capacitor is a device for storing charge, but it also says from a physical point of view, a capacitor does not store charge or electric current, but simply latent mechanical energy.
So what will be the answer?
Answer:
You are correct, the answer is capacitor
Calculate the magnitude of the linear momentum for the following cases.
(a) a proton with mass 1.67 x 10-27 kg, moving with a speed of 5.05 x 106 m/s
(d) the Earth (mass - 5.98 x 1024 kg) moving with an orbital speed equal to 2.98 x 10 m/s.
Answer:
8.4335 x 10^-²¹, 1.78204 x 10²⁶
Explanation:
p = mv
p = (5.05 x 10⁶)(1.67 x 10^-²⁷)
p = 8.4335 x 10^-²¹
p = mv
p = (5.98 x 10²⁴)(2.98 x 10)
p = 1.78204 x 10²⁶
Which graph shows constant acceleration with correctly placed independent and dependent variables?
Answer:
a = (V2 - V1) / t equation for constant acceleration
if t the independent variable is placed on the abcissa or x-axis and V the dependent variable is placed on the ordinate or y-axis then the acceleration would be the slope at the point considered.
A person lifts a ball of mass 1 kg through the
height of 1 m in 10 s. The average power
supplied by him is [Take g = 10 m/s²]
(2) 1 W
(4) 2 W
(1) 10 W
(3) 0.1 W
Answer:
1 W
Explanation:
Power is the ratio of the total work done by the body to the time it will takes to do the work.
Therefore Power = total work done ÷ timeTotal Work done = Potential energy (P.E) = mgh
Total work done = mgh
Total work done = 1kg × 10m/s² × 1m
Total work done = 10 J
Therefore Total Work done is 10J.
And then time is 10 s.
Power = Total Work done divided by time
Power = 10 J÷ 10 s = 1 W
Therefore Power is 1WA long thin solid rod lies along the positive x-axis. One end is at x = 1.80 m and the other at x = 3.40 m. The linear mass density is λ = a[tex]x^{3}[/tex] + bx, where λ is measured in kg/m, and the constants have the following values: a = 1.70 kg/[tex]m^{4}[/tex] and b = 2.20 kg/[tex]m^{2}[/tex].
1. Determine the total mass of the rod.
2. Calculate the x-coordinate of the center of the mass for this rod.
1. The total mass of the rod is 61.48 kg.
2. The x-coordinate of the center of the mass for this rod is 172.6021 m.
What is density?The density is the ratio of the mass and the volume of the object. It is denoted by ρ.
ρ = mass/Volume = m/V
Given a long thin solid rod lies along the positive x-axis. One end is at x = 1.80 m and the other at x = 3.40 m. The linear mass density is
λ = ax³ + bx,
where λ is measured in kg/m, and the constants have the following values: a = 1.70 kg/m⁴ and b = 2.20 kg/m²
So, λ = 1.70x³ + 2.20x
1. The total mass of the rod is
m =₁.₈³⁴ ∫ [1.70x³ + 2.20x] dx
m = [ 1.70x⁴/4 + 2.20x² /2 ]₁.₈³⁴
Putting the limits, we have
m = 69.51 - 8.02548
m = 61.48 kg
Thus, the total mass of the rod is 61.48 kg
2. The x-coordinate of the center of the mass for this rod
Xcm =∫ xλdx/m
Xcm =∫[ x ( 1.70x³ + 2.20x) /m ]dx
Xcm =∫[( 1.70x⁴ + 2.20x²) /m ]dx
On integrating and putting the limits x = 1.80 m to x = 3.40 m
Xcm = = [ {1.70(3.4)⁵/5 + 2.20(3.4)³ /3} - {1.70(1.8)⁵/5 + 2.20(1.8)³ /3} ]
Xcm = 183.3034 - 10.70133
Xcm = 172.6021 m
Thus, the x-coordinate of the center of the mass for this rod is 172.6021 m.
Learn more about density.
https://brainly.com/question/9215083
#SPJ1
If the mass of the falling object is 60kg. Calculate force. [Take g=10m/s2]
What is an advantage of using renewable energy resources?
A. They can be converted directly into electric energy.
B. They do not waste energy in heat.
C. They can be replenished in a human lifetime.
D. They do not produce greenhouse gases.
a 10.00mf parallel-plate capacitor is connected to a 24.0v battery. after the capacitor is fully charged ,the
battery is disconnected without loss of any of charge on the plates.
a) a voltmeter is connected across the two plates without discharging them.what does it read
b)what would the voltmeter read if the plate separationwere doubled?
The answer to the first part of the question is 24 V and the answer to the second part of the question is 48 V.
The formula which relates Charge, Capacitance and Voltage is
Charge = Capacitance × Voltage
Q = CV
where Q denotes the charge, C denotes the capacitance and V denote the voltage.
Using the above formula the charge on the capacitance will be
Q = CV
C = 10 mF
V = 24 V
Q = 240 mC
Charge on capacitance is 240 mC.
Now after we disconnect the battery
C = 10 mF (will remain same)
Q = 240 mC
V = Q/C
V = 240/10 V
V = 24 V
So after we removed the battery, The voltage will remain same.
Now we know that parallel plate capacitor formula is
C = ε(A/d)
from here
C ∝ 1/d, and as there is no loss of charge we can say that V ∝ 1/d
Form C ∝ 1/d and V ∝ 1/C we can state that
V ∝ d {where d is the measurement of separation between the plates}
so if we double the distance between the plates then, the voltage will also get double.
Previously our voltage was 24 V, now if we double the distance between the plates the voltage will also get double, and it will become 48 V.
So, the voltmeter will take a reading of 24 V if voltmeter is connected across the two plates without discharging them, and if we double the plate separation then it will take 48 V as reading.
Learn more about Capacitors here:
https://brainly.com/question/13578522
#SPJ10
What work do you think is done when you carry a 20 N weight backpack for a 1000 m walk? will the work be positive, negative, or potentially zero?
The work done is positive and is equal to 20000 J
What is work done?Work done is defined as the product of force and the distance moved by the force.
Mathematically:
Work done = force * distanceThe work done by the force = 20 * 1000 = 20000J
The work done is positive and is equal to 20000 J
Learn more about work done at: https://brainly.com/question/25923373
#SPJ1
How to do projects on newton’s law
What is the effect on a field of tall grass when a wave caused by a cool summer breeze passes through the field?
Select one:
a. The grass leans in the direction the wind is blowing, then returns to its original position.
b. The field of grass exhibits a permanent disturbance in the direction the wind is blowing.
c. To counteract the effect of the breeze, the grass leans into the wind.
d. Some grass leans in the direction the wind is blowing and some leans into the wind.
Whenever a wave is brought on by a cool summer breeze across the field. The grass tilts in the wind's direction before reverting to its original posture. Option A is correct.
What is the wind blowing?Air pressure variations within our atmosphere result in the wind, which is the movement of air.
Areas with a low pressure are approached by air in high pressure. The air flows more quickly when there is a bigger pressure differential. Most rapid winds.
The wind is the movement of air produced by changes in air pressure in our atmosphere.
High-pressure air goes toward low-pressure locations. The bigger the pressure differential, the faster the air moves.
Hence, option A is correct.
To learn more about the wind blowing refer;
https://brainly.com/question/14212137
#SPJ1
what will happen to the pressure in a gas if you compressed it into a volume that was one third the size? why?
Answer:
Pressure will triple (Boyle's Law)
Explanation:
Assuming a constant temperature: (compressing gases usually raises the temp significantly):
P1V1 = P2V2
P1V1 / V2 = P2
Now change V2 to 1/3 V2:
P1V1 / (1/3 V2 ) = P2 / (1/3 )
P1V1/ (1/3 v2 ) = 3 P2 <======= THE PRESSURE WILL TRIPLE
This is Boyle's Law
As you move down a period of the periodic table from top to bottom, what happens to the elements' electronegativity?
A.
It decreases.
B.
It changes in relation to the number of electrons.
C.
It changes in relation to the number of protons.
D.
It increases.
Answer:
A.) It decreases
Explanation:
Generally, as you go from the top to the bottom of the periodic table (down a column), the electronegativity values of the elements decrease.
Also, as you move to the right of the periodic table (across a period), the electronegative values increase. The most electronegative elements are located on the top-right of the periodic table.
8. A charged ball of mass m = 0.265 kg and unknown charge q is hanging by a light thread from a ceiling. A fixed charge Q = +5.00 μC on an insulated stand is brought close to the unknown charge. As a result, the unknown charge hangs at an angle 0 = 38.0° to the vertical as shown in the diagram below. The distance between the two charges is r = 22.0 cm. (a) What is the sign of the unknown charge? Explain how you know this. (b) What is the magnitude of the unknown charge? 8. A charged ball of mass m = 0.265 kg and unknown charge q is hanging by a light thread from a ceiling . A fixed charge Q = +5.00 μC on an insulated stand is brought close to the unknown charge . As a result , the unknown charge hangs at an angle 0 = 38.0 ° to the vertical as shown in the diagram below . The distance between the two charges is r = 22.0 cm . ( a ) What is the sign of the unknown charge ? Explain how you know this . ( b ) What is the magnitude of the unknown charge ?
(a) The sign of the unknown charge is negative.
(b) The magnitude of the unknown charge is 2.18 μC.
What is charge?The charge is the physical quantity which defines the object's electric field. The charged objects creates the electric field around it and attracts or repels another objects coming into that field.
Given is a charged ball of mass m = 0.265 kg and unknown charge q is hanging by a light thread from a ceiling. A fixed charge Q = +5.00 μC on an insulated stand is brought close to the unknown charge. As a result, the unknown charge hangs at an angle 0 = 38.0° to the vertical as shown in the diagram below. The distance between the two charges is r = 22.0 cm.
Tension in the string has two components, Tsinθ and Tcosθ
(a) The fixed charge Q will attract the movable charge q attached to string. The charge Q is positive. So, the charges must of opposite sign.
Thus, the sign of unknown charge is negative.
(b) From the equilibrium of forces, we get
Electrostatic force Fe = kQq/r²
Fe = Tsinθ .............(1)
and
weight force mg = Tcosθ.............(2)
Dividing both the equations, we get
mg/Fe = tanθ
mg / (kQq/r²) = tanθ
q = mgr²tanθ / kQ
Substitute the values from the question, we have
q = 0.265 x 9.81 x (0.22)² tan38 / (9x10⁹ x 5 x 10⁻⁶)
q = 2.18 x 10⁻⁶ C
or q = 2.18 μC
Thus, the magnitude of charge is 2.18 μC.
Learn more about charge.
https://brainly.com/question/19886264
#SPJ1
C1=10 μF , C2= 50 μF, C3=9 μF, C4=2 μF, C5= 0.1 μF
What is the equivalent capacitance of these capacitors as they are arranged?
The equivalent capacitance of these capacitors as they are arranged in series and parallel will be 0.093 μF and 71.1 μF.
What is a capacitor?A capacitor is a device that can store electrical energy. It is a two-conductor configuration separated by an insulating medium that carries charges of equal size and opposite sign.
If the capacitor is connected in the series the equivalent capacitance is found as;
[tex]\rm \frac{1}{c_{eq}} = \frac{1}{c_1} +\frac{1}{c_2} +\frac{1}{c_3} +\frac{1}{c_4} +\frac{1}{c_5} \\\\\ \rm \frac{1}{c_{eq}} = \frac{1}{10} +\frac{1}{50} +\frac{1}{9} +\frac{1}{2} +\frac{1}{0.1} \\\\\ \frac{1}{c_{eq}} = 0.1+0.02+0.11+0.5+10 \\\\ \frac{1}{c_{eq}} = 10.7 \\\\ c_{eq} = 0.093 \ \mu F[/tex]
If the capacitor is connected in parallel the equivalent capacitance,cₐ is found as;
cₐ= c₁+c₂+c₃+c₄+c₅
cₐ = 10+50+9+2+0.1 μF
cₐ =71.1 μF
Hence, the equivalent capacitance of these capacitors as they are arranged in series and parallel will be 0.093 μF and 71.1 μF.
To learn more about the capacitor, refer to the link;
https://brainly.com/question/14048432
#SPJ1
Gravity will have a greater effect on an object with?
Which is not an example of static electricity?
A. Clothes sticking together in the dryer
B. Getting shocked when you touch a door knob
C. plugging in a lamp
Answer asap
Plugging in a lamp is not an example of Static electricity. Thus, the correct option is C.
What is Static electricity?Static electricity may be defined as the consequence of an imbalance between negative and positive charges in an object. It does not involve the direct flow of electrons throughout a wire.
Clothes sticking together in the dryer and getting shocked when you touch a doorknob are examples of static electricity while plugging in a lamp is an example of mobile electricity that mediates the direct flow of electrons to generate an electric current and as a result, the lamp glows.
Therefore, the correct option for this question is C.
To learn more about Static electricity, refer to the link:
https://brainly.com/question/4918499
#SPJ1
A comet goes around the sun in an elliptical orbit. At its farthest point, 455 million miles from the sun, it is traveling with a speed of 15,135 mi/h. How fast is it traveling at its closest approach to the sun, at a distance of 116 million miles?
Answer:
A 2kg block is moved a long a level floor by a horizontal force of 20N if the coefficient of sliding friction is 0.4
what is the acceleration of the blove
If a crane worker lifts a crate with a mass of 250 kg from the ground to a
shipping container that is 20 meters off the ground, by how much has the
worker increased the gravitational potential energy of the crate? (Recall that g
= 9.8 m/s²)
A. 75,000 J
B. 61,000 J
C. 83,000 J
D. 49,000 J
D.
The gravitational of a body is possessed by the body due to the virtue of its position.
The formula for gravitational potential energy is,
P.E = mgh joules
Substituting the values
196*9.8*250= 49k
Which of the following best represents the energy transformations in an
electric motor?
A. Mechanical energy
in electromagnet
-
changing electric field -> electrical energy
B. Electrical energy in current → magnetic energy in electromagnet
OC. Electrical energy in current → changing magnetic field →
mechanical energy
-
OD. Mechanical energy → changing magnetic field → electrical
energy in current
The energy transformations in an electric motor are, electrical energy in current → changing magnetic field → mechanical energy. Option C is corect.
What is the law of conservation of energy?According to the law of conservation of energy, energy can neither be created nor destroyed, but it can be transferred from one form to another.
The total energy is the sum of all the energies present in the system. The potential energy in a system is due to its position in the system.
An electric motor is a mechanism that turns electricity into mechanical energy.
The interaction between the motor's magnetic field and electric current in a wire winding generates force in the form of torque imparted to the motor's shaft in most electric motors.
An electric generator is physically equivalent to an electric motor, but it converts mechanical energy into electrical energy using a reversed flow of power.
In an electric motor, energy is transformed into mechanical energy, electrical energy in current, and changing magnetic energy.
The energy transformations in an electric motor are;
Electrical energy in current → changing magnetic field → mechanical energy.
Hence option C is correct.
To learn more about the law of conservation of energy, refer to https://brainly.com/question/2137260.
#SPJ1
According to the __________perspective, people who suffer from PTSD are classically conditioned.
According to the pavlovian perspective, people who suffer from PTSD are classically conditioned.
What is PSTD?
This is referred to as post traumatic stress disorder which is a mental disorder from a terrifying incident.
The pavlovian perspective however view this disorder as being a type of classical conditioned one.
Read more about Post traumatic stress disorder here https://brainly.com/question/943079
#SPJ1
I was having trouble converting this p-t graph into a velocity-time graph and acceleration-time graph. Can someone convert it and send a picture of it?
We can obtain the velocity from the graph and plot is against time to obtain a velocity time graph.
What is a velocity time graph?The velocity time graph shows the change of velocity with time. Recall that velocity is the change of position with time.
As such, when we have a position time graph as shown, we can obtain the velocity from the graph and plot is against time to obtain a velocity time graph.
Learn more about velocity time graph:https://brainly.com/question/11290682
#SPJ1
How do we solve questions C and D? I already did A and B and I am confused on how to continue
(a) The work done in moving the unit charge from point C to A is 7.62 x 10⁻³ J.
(b) The work done in moving the unit charge from point D to B is 7.62 x 10⁻³ J.
Work done in moving the charge from C to A
W = Fd
W = Kq²/d
from 0 origin to C, d = √(5² + 5²) = 7.07 mfrom 0 origin to A, d = 5 mW(C to A) = W(0 to C) + W(0 to A)
[tex]W(C \ to \ A) = - \frac{Kq^2}{7.07} + \frac{Kq^2}{5} \\\\ W(C \ to \ A) = 0.0586 \ Kq^2\\\\W(C \ to \ A) = 0.0586 \times 9 \times 10^9 \times (3.8\times 10^{-6})^2\\\\W(C \ to \ A) = 7.62 \times 10^{-3} \ J[/tex]
Work done in moving the charge from D to Bfrom 0 origin to D, d = √(5² + 5²) = 7.07 mfrom 0 origin to B, d = 5 mW(D to B) = W(0 to D) + W(0 to B)
W(D to B) = 7.62 x 10⁻³ J
Learn more about work done here: https://brainly.com/question/25573309
#SPJ1
when energy is transferred from one part of a system to another, some of the energy is lost during the transfer and cannot be used as it was intended. Which two sentences describes examples of this?
Sentences A and D describe examples of energy transformation.Heat is produced when a car's tires rub against the pavement and as electricity passes across power wires, they become hotter.
What is the law of conservation of energy?According to the law of conservation of energy, the energy of an isolated system stays unchanged throughout time.it is said to be conserved.
Energy cannot be created nor destroyed and can be transferred from one form to the other form.
The complete question is
"When energy is moved from one component of a system to another, some of the energy is lost and cannot be used as planned.
Which two statements provide examples?
A. Friction between a car's tires and the road produces heat.
B. Sunlight strikes a solar panel, generating electricity.
c. Stereo speakers emit a sound when powered by electrical energy,
D. Wind moves a turbine, generating electricity.
I E. Power lines heat up as electricity flows through them."
Some of the energy wasted during the movement of energy from one section of a system to another is heat is produced by friction between a car's tires and the road and as electricity passes via power lines, they heat up.
Hence, sentences A and D describe examples of energy transformation.
To learn more about the law of conservation of energy refer to the link;
https://brainly.com/question/2137260
#SPJ1
