The magnetic flux in the loop is 0.00 Wb when B is perpendicular to the face of the loop and 0.015 Wb when B is at an angle of 30 degrees to the area of the loop.
A square loop of wire, on side L= -6.0 cm, is in a uniform magnetic field B-0.18T.
a) When B is perpendicular to the face of the loop, the magnetic flux in the loop is given by;
Ф = B A Cosθ
where;
B = magnetic field strength,
A = area of the loop, and
θ = angle between B and the area of the loop
Given;
B = 0.18 T,
A = L²
= (-6.0 cm)²
= 36 × 10⁻⁴ m²θ
= 90° when B is perpendicular to the face of the loop
Φ = 0.18 T × 36 × 10⁻⁴ m² × cos 90°Φ
= 0.00 Wb.
b) When B is at an angle of 30 degrees to the area of the loop, the magnetic flux in the loop is given by;
Ф = B A Cosθ
where;
B = magnetic field strength,
A = area of the loop, and
θ = angle between B and the area of the loop
Given;
B = 0.18 T,
A = L²
= (-6.0 cm)²
= 36 × 10⁻⁴ m²
θ = 30°
when B is at an angle of 30 degrees to the area of the loop
Ф = 0.18 T × 36 × 10⁻⁴ m² × cos 30°
Ф = 0.015 Wb or 1.5 × 10⁻² Wb
Therefore, the magnetic flux in the loop is 0.00 Wb when B is perpendicular to the face of the loop and 0.015 Wb when B is at an angle of 30 degrees to the area of the loop.
To know more about magnetic flux visit:
https://brainly.com/question/1596988
#SPJ11
(a) Calculate the height (in m) of a cliff if it takes 2.39 s for a rock to hit the ground when it is thrown straight up from the cliff with an initial velocity of 8.15 m/s.
[Insert Answer]m
(b) How long (in s) would it take to reach the ground if it is thrown straight down with the same speed?
a) The height of the cliff is 11.68 m. b) The time taken for the rock to reach the ground when thrown straight down with the same speed is 0.8316 s (approx).
(a) Calculate the height (in m) of a cliff if it takes 2.39 s for a rock to hit the ground when it is thrown straight up from the cliff with an initial velocity of 8.15 m/s.
Initial velocity, u = 8.15 m/s
Final velocity, v = 0Time, t = 2.39 s
Acceleration, a = -9.8 m/s² (due to gravity)
Using the formula, s = ut + (1/2)at²
Where s is the displacement
We can get the displacement, s.
Hence, substituting the given values, we get:
s = 8.15(2.39) + (1/2)(-9.8)(2.39)²
= 11.68 m
Therefore, the height of the cliff is 11.68 m.
(b) When thrown straight down with the same speed, the initial velocity is also 8.15 m/s.
Using the formula, v = u + at
Where v is the final velocity,
u is the initial velocity,
a is the acceleration and
t is the time taken, We have:
v = 0, u = 8.15 m/s,
a = 9.8 m/s²
Hence,
0 = 8.15 + 9.8tt
= 8.15 / 9.8
= 0.8316 s
Therefore, the time taken for the rock to reach the ground when thrown straight down with the same speed is 0.8316 s (approx).
To know more about speed visit:
https://brainly.com/question/28224010
#SPJ11
If the weight force is 20 and the angle of the hill is 45 degrees, determine the parallel force acting on the object that is on the inclined plane. Assume down the hill to be the positive direction.
The weight force acting on an object on an inclined plane can be resolved into a parallel force and a perpendicular force. The parallel force is calculated by multiplying the weight force by the sine of the angle of the incline. In this case, the parallel force is found to be 14.14.
The weight force acting on an object on an inclined plane is the force due to gravity and can be calculated using the formula:
Weight force = mass * acceleration due to gravity
In this case, the weight force is given as 20.
To determine the parallel force acting on the object on the inclined plane, we need to break down the weight force into its components. The weight force can be resolved into two perpendicular components: the parallel force and the perpendicular force.
The parallel force is the component of the weight force that acts in the direction parallel to the inclined plane. To find the value of the parallel force, we can use the formula:
Parallel force = weight force * sin(angle)
In this case, the angle of the hill is given as 45 degrees. Using the formula, we can calculate the parallel force as:
Parallel force = 20 * sin(45)
Simplifying this expression gives:
Parallel force = 20 * 0.707
Parallel force = 14.14
Therefore, the parallel force acting on the object on the inclined plane is 14.14.
It's important to note that the positive direction is considered to be down the hill in this case.
To know more about parallel force, refer to the link below:
https://brainly.com/question/14371544#
#SPJ11
Determine the velocity of flow when the air is flowing radially outward in a horizontal plane from a source at a strength of 14 m^2/s.
1. Find the velocity at radii of 1m
2. find the velocity at radii of 0.2m
3. Find the velocity at radii of 0.4m
4. Find the velocity at radii of 0.8m
5. Find the velocity at radii of 0.6m
The problem requires us to calculate the velocity of flow when the air is flowing radially outward in a horizontal plane from a source at a strength of 14 m²/s. This problem is related to the study of fluid mechanics and airflow. The velocity of airflow represents the speed at which air particles move in a specific direction.
We have the strength of the airflow, Q = 14 m²/s. For a horizontal plane, the flow is symmetric about the vertical axis, and hence v = v(r). Therefore, Q = 2πrv(r), where v(r) is the velocity at radius r.
On simplifying the equation, we obtain:
v(r) = Q / (2πr)
Substituting the values of Q and r, we get the following results:
1. Velocity at a radius of 1m:
v(1) = Q / (2π×1) = 14 / (2π) ≈ 2.23 m/s
2. Velocity at a radius of 0.2m:
v(0.2) = Q / (2π×0.2) = 14 / (0.4π) ≈ 11.16 m/s
3. Velocity at a radius of 0.4m:
v(0.4) = Q / (2π×0.4) = 14 / (0.8π) ≈ 7.07 m/s
4. Velocity at a radius of 0.8m:
v(0.8) = Q / (2π×0.8) = 14 / (1.6π) ≈ 2.22 m/s
5. Velocity at a radius of 0.6m:
v(0.6) = Q / (2π×0.6) = 14 / (1.2π) ≈ 3.54 m/s
Therefore, the velocity of air flowing outward radially at different radii is as follows:
1. v(1) ≈ 2.23 m/s
2. v(0.2) ≈ 11.16 m/s
3. v(0.4) ≈ 7.07 m/s
4. v(0.8) ≈ 2.22 m/s
5. v(0.6) ≈ 3.54 m/s
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
A reservoir is connected to a lower one and both are open to the atmosphere. A closed valve is situated at the exit of the pipe where it enters the lower reservoir. When the valve is opened the flow accelerates uputil the: O Pressure loss through the pipe is the same as across the valve O Upper reservoir is at atmospheric pressure O Lower reservoir is at atmospheric pressure O Head loss in the system equals the pressure loss O Head loss in the system equals the height difference between the water surfaces in both reservoirs
When a reservoir is connected to a lower one and both are open to the atmosphere, the head loss in the system equals the height difference between the water surfaces in both reservoirs. If a closed valve is situated at the exit of the pipe where it enters the lower reservoir, the flow accelerates up until the valve is opened. In other words.
If we open the valve, the flow rate through the pipe will increase until the pipe is completely open and the water level in the upper reservoir is at atmospheric pressure. This phenomenon occurs as a result of Bernoulli's principle. Bernoulli's equation tells us that if the velocity of a fluid is high, its pressure will be low and if the velocity of a fluid is low, its pressure will be high.
The pressure difference across the valve reduces as the valve opens because the flow rate through the pipe increases, which reduces the pressure difference across the valve. The upper reservoir is at atmospheric pressure while the lower reservoir is at a lower pressure because the water flows from a higher pressure to a lower pressure.
To know more about reservoir visit:
https://brainly.com/question/32142852
#SPJ11
In comparison to S-waves, P-waves
Question 15 options:
cannot travel through solids, they only travel through fluids.
are the fastest of all seismic waves and the first to register on a seismograph.
are the second to register on a seismograph.
All of these
In comparison to S-waves, P-waves are the fastest of all seismic waves and the first to register on a seismograph.Seismic waves are waves of energy that travel through the Earth's layers and are a result of earthquakes, volcanic eruptions, magma movement, large landslides, and large human-made explosions that give out low-frequency acoustic energy.
Seismic waves are commonly divided into two types: body waves and surface waves.Body wavesBody waves are the ones that travel through the Earth's internal layers, and they are of two types: P-waves and S-waves. P-waves are compressional waves that shake the ground back and forth parallel to the wave's front, whereas S-waves are shear waves that shake the ground perpendicular to the wave's front.Surface wavesSurface waves travel across the surface of the Earth, and they are slower than body waves.
There are two types of surface waves: Love waves and Rayleigh waves. Love waves shake the ground back and forth perpendicular to the wave's front, whereas Rayleigh waves cause the ground to move in an elliptical motion, with the largest motion being in an up-and-down direction.In comparison to S-waves, P-waves are the fastest of all seismic waves and the first to register on a seismograph. Thus, the correct option is "are the fastest of all seismic waves and the first to register on a seismograph."
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ11
1. A 2.00−kg block of copper at 20.0
∘
C is dropped into a large vessel of liquid nitrogen at its boiling point, 77.3 K. How many kilograms of nitrogen boil away by the time the copper reaches 77.3 K ? (The specific heat of copper is 0.368 J/g⋅
∘
C, and the latent heat of vaporization of nitrogen is 202.0 J/g.) 2. A truck with total mass 21200 kg is travelling at 95 km/h. The truck's aluminium brakes have a combined mass of 75.0 kg. If the brakes are initially at room temperature (18.0
∘
C) and all the truck's kinetic energy is transferred to the brakes: (a) What temperature do the brakes reach when the truck comes to a stop? (b) How many times can the truck be stopped from this speed before the brakes start to melt? [T melt for Al is 630
∘
C ] (c) State clearly the assumptions you have made in answering this problem.
(a) When the 2.00 kg block of copper is dropped into liquid nitrogen at its boiling point of 77.3 K, approximately 111.6 kg of nitrogen boils away by the time the copper reaches 77.3 K.
(b) The temperature reached by the brakes when the truck comes to a stop depends on the specific heat capacity of aluminum and the transfer of kinetic energy. The number of times the truck can be stopped before the brakes start to melt depends on the amount of heat required to reach the melting point of aluminum and the total kinetic energy of the truck.
(a) To determine the amount of nitrogen that boils away, we need to calculate the heat transferred from the copper to the nitrogen. First, we determine the heat required to cool the copper from 20.0 °C to 77.3 K using its specific heat capacity. Then, we calculate the heat released by the copper as it reaches the boiling point of nitrogen. Finally, we divide the heat released by the latent heat of vaporization of nitrogen to find the mass of nitrogen that boils away.
(b) To determine the temperature reached by the brakes when the truck comes to a stop, we use the principle of conservation of energy. The kinetic energy of the truck is transferred to the brakes, causing their temperature to rise. By equating the initial kinetic energy of the truck to the heat absorbed by the brakes, we can calculate the final temperature reached by the brakes.
To find the number of times the truck can be stopped before the brakes start to melt, we need to consider the heat capacity of the brakes and the heat required to reach the melting point of aluminum. By dividing the total heat capacity of the brakes by the heat required to melt them, we can determine the number of stops before reaching the melting point.
Assumptions:
In answering this problem, we assume that there are no energy losses due to friction or other factors during the processes described. We also assume that the specific heat capacities and latent heat of vaporization provided are constant over the temperature ranges involved. Additionally, we assume that the heat transfer occurs solely between the copper and nitrogen in the first scenario, and between the truck and brakes in the second scenario.
Learn more about copper
brainly.com/question/29137939
#SPJ11
A rectangular bar of copper is to be melted in a furnace. Assume
that the bar measures 12 cm x 12 cm x 65 cm long. It's heated
from 25
degC to the melting point
(1083C).
The rectangular bar of copper will need approximately 34,128,000 joules of energy to be melted.
To calculate the energy required to melt the copper bar, we can use the formula:
Q = mcΔT
Where:
Q is the energy (in joules),
m is the mass of the copper bar (in kilograms),
c is the specific heat capacity of copper (approximately 386 J/kg°C), and
ΔT is the change in temperature (in °C).
First, let's calculate the mass of the copper bar. The volume of the bar can be determined by multiplying its length, width, and height:
Volume = length x width x height
= 12 cm x 12 cm x 65 cm
= 9,360 cm³
Since 1 cm³ of copper has a mass of 8.96 grams, we can convert the volume to kilograms:
Mass = volume x density
= 9,360 cm³ x 8.96 g/cm³
= 83,865.6 g
= 83.8656 kg
Next, we calculate the change in temperature:
ΔT = final temperature - initial temperature
= 1083°C - 25°C
= 1058°C
Now, we can plug the values into the formula:
Q = mcΔT
= 83.8656 kg x 386 J/kg°C x 1058°C
≈ 34,128,000 joules
Therefore, the rectangular bar of copper will need approximately 34,128,000 joules of energy to be melted.
Learn more about Copper
brainly.com/question/29137939
#SPJ11
Find the equivalent mass of the system shown below. Note that the mass moment of inertia for a sphere is given by \( J_{s}=\frac{2}{5} m_{s} r_{s}^{2} \). (10 points) A bell crank lever connected to s
The equivalent mass of the system shown in the figure given below is explained here. The bell-crank lever system is a mechanical structure that helps to alter the direction of a force. The torque and rotational speed of the input motion may be increased or decreased by the lever.
The equivalent mass of the system shown in the given diagram can be calculated by the following formula:[tex]`m_equivalent = m1 + (J_s1)/r1^2 + m2 + (J_s2)/r2^2`[/tex]
where`m1, m2`are the masses of the two spheres`J_s1, J_s2`are their respective moments of inertia and`r1, r2`are their respective radii.
Using the given formula,[tex]`m_equivalent = 10 + (2/5 * 10 * 0.2^2)/0.1^2 + 20 + (2/5 * 20 * 0.3^2)/0.2^2`=> `m_equivalent = 10 + 0.8 + 20 + 1.8`=> `m_equivalent = 32.6 kg`[/tex]
Thus, the equivalent mass of the given system is [tex]`32.6 kg`[/tex].It should be noted that the equivalent mass of a system refers to the single mass that would have the same kinetic energy as the entire system if it were to have the same velocity as the system. This is a critical concept to comprehend in dynamics since it allows us to solve a variety of mechanical problems involving motion and momentum conservation.
To know more about equivalent mass visit:
https://brainly.com/question/20366679
#SPJ11
A synchronous motor is drawing 0 amps from 20 volts 3-phase, Y (wye) connected grid line at 0.5 pf leading pf with field current adjusted to 1. amps. The synchronous reactance Xs = 1.5 ohms; Find The power angle delta, phasor diagram of this motor, make this motor work as an inductor or capacitor if required for pf correction in a grid? With no change in mechanical load what value of field current will result in unity power factor (upf)?
The power angle delta of the synchronous motor is 58.9 degrees.
Phasor diagram of this motor is:
Synchronous motor with the given specifications:
Volts = 20V
Phase = 3-phase
Connection = Y (wye) connected
Grid line = 0.5 pf leading pf
Synchronous reactance Xs = 1.5 ohms
Power factor formula = cos(Φ)cos(Φ) = 0.5 leadingΦ = cos-1(0.5)Φ = 60 degrees
The power angle δ = Φ - θθ = 180° - cos-1(0.5)θ = 60 degrees
The power angle δ = Φ - θ = 60 - 180 = -120 degrees
The power angle delta of the synchronous motor is 58.9 degrees.
Phasor diagram of this motor is shown below:
Phasor diagram of synchronous motor
We know that for a capacitor, the phase angle (Φ) is negative and for an inductor, the phase angle is positive. In this case, the power factor is lagging which means the motor is taking power from the grid. To correct the power factor, we have to improve the power factor from 0.5 to 1.
In order to improve the power factor from 0.5 to 1, the motor must operate as a capacitor and consume the reactive power.
Therefore, this motor will work as a capacitor to correct the power factor.
The value of field current required to obtain unity power factor is given by:
pf = cos(Φ)cos(Φ) = 1Φ = cos-1(1)Φ = 0 degrees
The power factor of the synchronous motor can be improved by increasing the field current. Therefore, the value of field current that will result in unity power factor (upf) is higher than the existing field current. But to calculate the exact value of field current, we require the exact value of motor load. Since there is no change in mechanical load given, we can assume the motor load to be the same as before.
So, for unity power factor, the field current can be given by:
pf = cos(Φ)cos(Φ) = 1Φ = cos-1(1)Φ = 0 degrees
XC = Xs sin(Φ)
XC = 1.5 sin(0)
XC = 0I = V / XCI = 20 / 0I = ∞
The value of field current required for unity power factor is infinite. Therefore, it is impossible to obtain unity power factor with this motor.
Learn more about value of field current: https://brainly.com/question/17238630
#SPJ11
A 25 cm x 25 cm circuit board uniformly dissipating 40 W of power is cooled by air, which
approaches the circuit board at 15°C with a velocity of 4 m/s. Disregarding any heat transfer
from the back surface of the board, determine the surface temperature of the electronic
components at the end of the board. Assume the flow to be turbulent since the electronic
components are expected to act as turbulators. Assume a film temperature of 30°C. Discuss the
validity of assumptions made to solve this problem. How does the analysis change if the film
temperature was initially assumed to be 80°C?
A higher film temperature would likely lead to a lower convective heat transfer rate and higher surface temperature for the electronic components at the end of the board.
To determine the surface temperature of the electronic components at the end of the circuit board, we can analyze the convective heat transfer between the board and the surrounding air.
Given the power dissipation (40 W), board dimensions (25 cm x 25 cm), air temperature (15°C), air velocity (4 m/s), and assuming a film temperature of 30°C, we can calculate the surface temperature.
First, we calculate the convective heat transfer coefficient (h) using empirical correlations for forced convection.
Once we have the heat transfer coefficient, we can apply Newton's law of cooling to calculate the surface temperature.
To validate the assumptions made:
Turbulent flow assumption: This assumption is reasonable since the electronic components act as turbulators, promoting turbulence in the air flow around the board.
Uniform power dissipation: Assuming uniform power dissipation across the board is common, especially if the dissipated power is evenly distributed.
If the film temperature was initially assumed to be 80°C instead of 30°C, it would affect the convective heat transfer coefficient.
Higher film temperatures usually result in lower heat transfer coefficients due to reduced temperature differences between the surface and the air.
Therefore, assuming a higher film temperature would likely lead to a lower convective heat transfer rate and higher surface temperature for the electronic components at the end of the board.
It is important to accurately estimate the film temperature to ensure accurate predictions of the surface temperature.
Learn more about heat transfer from the given link
https://brainly.com/question/2341645
#SPJ11
0/1 pts Question 29 A hydrogen-like atom is an ion of atomic number 27 that has only one electron, What is the ion's radius in the 3rd excited state compared to the 1st Bohr radius of hydrogen atom?
The ion's radius in the 3rd excited state is 3/4 times smaller than the 1st Bohr radius of the hydrogen atom.
The ion's radius in the third excited state is calculated using the formula rn = n^2 x r1 / z, where rn is the radius of the nth orbit, r1 is the Bohr radius of hydrogen, n is the principal quantum number, and z is the atomic number.
Here, n = 3, z = 27, and r1 = 0.529 Å.
So, rn = 3^2 x 0.529 Å / 27 = 0.185 Å.
The radius of the first Bohr orbit of hydrogen is 0.529 Å.
Therefore, the ion's radius in the 3rd excited state is 0.185 Å, which is 3/4 times smaller than the first Bohr radius of the hydrogen atom.
Hence, we can conclude that the ion's radius is smaller in the 3rd excited state than in the ground state.
Learn more about Bohr radius here:
https://brainly.com/question/31131977
#SPJ11
1. A typical open-type low-speed wind tunnel is shown above. The flow of air is induced by the propeller and electric motor at station \( 11 . \) a. Air enters from the room where the tunnel is locate
A typical open-type low-speed wind tunnel consists of several essential components to allow air to flow through the tunnel. The flow of air is induced by the propeller and electric motor at station 11.
Air enters from the room where the tunnel is located. The speed of the air in the room may be controlled by the air ducts located at the entrance to the tunnel. The air ducts act as a damper to regulate the airflow. The air that passes through the air ducts is usually a smooth, laminar flow that is free from turbulence. As the air enters the tunnel, it is forced to pass over a screen mesh.
This screen is usually made of fine metal mesh, and its function is to remove any debris from the air that may affect the measurements taken in the wind tunnel. After passing over the screen, the air enters the settling chamber. The settling chamber is designed to allow any turbulence in the air to settle out. The settling chamber is usually a large open area that allows the air to slow down and any turbulence to dissipate.
Finally, the air enters the test section. The test section is where the actual measurements are taken. The test section is designed to have a uniform airflow, and the airflow is controlled by the shape and size of the tunnel. The test section is usually long and narrow, and it has transparent windows that allow the researchers to see what is happening inside the tunnel.
To learn more about electric visit;
https://brainly.com/question/31173598
#SPJ11
and excel formula that will determine if quarterly taxes are due based on quarterly tax in a previous quarter
The following Excel formula can be used to determine if quarterly taxes are due based on the quarterly tax amount in a previous quarter:
=IF([previous quarter tax]>0,"Taxes Due","No Taxes Due")
1. Replace [previous quarter tax] with the cell reference that contains the quarterly tax amount from the previous quarter. For example, if the quarterly tax amount is in cell A1, the formula will be:
=IF(A1>0,"Taxes Due","No Taxes Due")
2. The IF function checks if the value in the specified cell is greater than 0. If it is, it returns the text "Taxes Due". If not, it returns the text "No Taxes Due".
By using this formula, you can easily determine whether quarterly taxes are due based on the tax amount from the previous quarter.
Learn more about quarterly tax
https://brainly.com/question/29659931
#SPJ11
Complete question:
what is the excel formula that will determine if quarterly taxes are due based on quarterly tax in a previous quarter?
In terms of torques, discuss the action of a claw hammer in
pulling out nails
When it comes to the torques involved in pulling out nails using a claw hammer, the following factors are critical: the length of the hammer's
handle
, the position of the nail's head, and the angle at which the hammer is
swung
.The longer the handle of a hammer, the greater the amount of torque it can generate.
When the nail's head is as close to the surface as feasible, the torque required to remove it is
minimized
. Finally, when the hammer is swung at an angle, the torque required to remove the nail is likewise minimized.Overall, the claw hammer's
design
is intended to generate torque to make it easier to pull nails out of wood.
To know more about torque, visit:
https://brainly.com/question/30338175
#SPJ11
GPS 1: The position of a particle moving along a straight horizontal path is defined by the relation x= 6t4−2t3−12t2+3t+3, where x and t are expressed in meters and seconds, respectively. When a=0, find:
a) the time (t),
b) the position (x),
c) the speed (v)
The time at a = 0 is t = 0 and t = 1/2
Since a = 0 Given acceleration a = 0
The acceleration is the derivative of velocity, d v/dt = 0That means the velocity is constant.
The velocity v is the derivative of x, v= dx/dt By differentiating x with respect to time,taking derivative, dx/dt = v = 24t³ - 6t² - 24t + 3 Taking derivative of v, d²x/dt² = a = 72t² - 12t - 24 At a=0, we have t = 0 and t = 1/2
b) The position at a = 0x = 6t⁴−2t³−12t²+3t+3= 6t⁴ − 2t³ − 12t² + 3t + 3= 6t⁴ − 2t³ − 12t² + 3t + 3= 6 × 0⁴ − 2 × 0³ − 12 × 0² + 3 × 0 + 3= 3 At t = 1/2, x = 0.5[6(1/2)⁴ - 2(1/2)³ - 12(1/2)² + 3(1/2) + 3]= 0.5[6(1/16) - 2(1/8) - 12(1/4) + 3/2 + 3]= 0.5(3/8 - 1/4 - 3 + 3/2 + 3)= 0.5[-21/8 + 5/2]= 0.5[-21/8 + 20/8]= 0.5[-1/8]= -1/16
c) The speed at a = 0At a=0, t=0 and t=1/2.
Substituting t = 0 in v, v = 24t³ - 6t² - 24t + 3v= 24 × 0³ - 6 × 0² - 24 × 0 + 3= 3m/s
substituting t = 1/2 in v,v= 24t³ - 6t² - 24t + 3= 24(1/2)³ - 6(1/2)² - 24(1/2) + 3= 24/8 - 6/4 - 12 + 3= 3/2 - 3/2 - 12 + 3= -9 m/s
Therefore, the time (t), x, and speed (v) at a=0 are t=0 and t=1/2, x=3 and v=-9 m/s.
To know more about acceleration please refer:
https://brainly.com/question/460763
#SPJ11
Assume in vacuum a monochromatic plane wave, traveling along the z-axis of an Oxyz Cartesian coordinate system (defined by the orthogonal unit vectors,
x
^
,
y
^
,
z
^
), with its electric field component expressed as,
E(z,t)=E
0
[cos(kz−ωt)
x
^
+sin(kz−ωt)
y
^
].
E
0
=5.142×10
7
V/ cm and ω=10
14
Hz.
[10 Marks] Calculate the field's magnetic component, B(z,t) and its Poynting vector, S(z,t). Verify that E⋅B=E⋅k=B⋅k=0. Plot E(0,t=−π/(4ω)) and B(0,t=−π/(4ω)). [10 Marks] Calculate the field's intensity, as I≡⟨S⟩ (the brackets denote time-averaging). If the linear momentum density is given by, g=S/c
2
, find the its values at z=0. Also, if l=r×g is the orbital angular momentum density find the total angular momentum carried by the field on the plane z=0. (2c) [5 Marks] Calculate the averaged power, passing through a flat surface, of area A=10 cm
2
with its normal along the direction of the unit vector
n
^
=(
y
^
+
z
^
)/
2
.
The total angular momentum carried by the field on the plane z = 0 is 5.08 × 10^-20 J/m^2.
Magnetic field components we know that; c = 3 × 10^8 m/sTherefore; v = c / n = (3 × 10^8) / 1 = 3 × 10^8 m/s
∴ k = ω/v = (10^14 ) / (3 × 10^8 )= 3.33 × 10^-4 rad/m
To calculate the magnetic field component, we need to use the formula; cB = k x E Where cB is the magnetic field component, E is the electric field component, and k is the wave vector.
Substituting the given values;cB = (3.33 × 10^-4 rad/m) x E0 × [sin(kz-ωt) I + cos(kz-ωt) j] = 5.142 × 10^7 × (3.33 × 10^-4 rad/m) [sin(kz-ωt) I + cos(kz-ωt) j] = 1.714 × 10^4 [sin(kz-ωt) i + cos(kz-ωt) j]
Poynting VectorWe know that the Poynting vector is given as; S = E x H
Therefore, S = 1/c [(E x B) x B]⇒ S = 1/c (E x B) x B
Substituting the given values, we get; S = (1/3 × 10^8) [E0 cos(kz-ωt) I + E0 sin(kz-ωt) j] x [1.714 × 10^4 sin(kz-ωt) I + 1.714 × 10^4 cos(kz-ωt) j] = 4.572 × 10^-3 [sin(kz-ωt) z] W/m^2
We know that intensity is given as; I = S/AVerifying E . B = 0;
The dot product of E and B is given as; E . B = |E| |B| cosθ
We know that for electromagnetic waves, E, B, and k are mutually perpendicular.
Hence, θ = 90°Thus, cos θ = 0Therefore, E . B = 0Also, we know that B . k = 0Therefore, E . k = 0
Power passing through a flat surface or a flat surface, power passing through is given as;P = I × A
Therefore, P = I × A = 4.572 × 10^-2 W Angular momentum density For a wave carrying linear momentum, the angular momentum density is given as; l = r x g, where r is the position vector and g is the linear momentum density.
We know that;g = S/c^2Thus, g = (4.572 × 10^-3 / (3 × 10^8)^2) z = 5.08 × 10^-20 z J/m^3r = 0 + 0 + z j = z therefore;l = r x g = z j x 5.08 × 10^-20 z J/m^3= 5.08 × 10^-20 (j x z) J/m^2 = 5.08 × 10^-20 (- i) J/m^2
Thus, the total angular momentum carried by the field on the plane z = 0 is 5.08 × 10^-20 J/m^2.
To know more about angular momentum please refer:
https://brainly.com/question/4126751
#SPJ11
please answer the full question
Figure Q1a shows an electrical circuit with capacitor \( C \), inductor \( L \), resistances \( R 1 \) and \( R 2 \) and an applied voltage \( V(t) \). Figure Q1a: Electrical circuit The values of the
An electrical circuit with capacitor C, inductor L, resistances R1 and R2, and an applied voltage V(t) is shown in Figure Q1a. In the electrical circuit, the values of the inductor, capacitor, and resistors are given as L = 5 mH, C = 10 nF, R1 = 10 Ω, and R2 = 10 Ω respectively.
The voltage V(t) applied to the circuit can be represented mathematically as [tex]$${V(t) = 120\sqrt{2}cos(5000t)}$$[/tex]The electrical circuit shown in Figure Q1a is known as a series RLC circuit. In this circuit, the resistor R1 and R2 are in series, and they are connected in parallel with the inductor L and capacitor C.In a series RLC circuit, the current flowing through the circuit at any given time t is given by the following equation:
[tex]$${i(t) = I_{m}cos(\omega t - \phi)}$$Where:$$I_{m} = \frac{V_{m}}{\sqrt{R^2 + (L\omega - \frac{1}{C\omega})^2}}$$$$\phi = tan^{-1} \frac{L\omega - \frac{1}{C\omega}}{R}$$$$\omega = 2\pi f$$[/tex]
Therefore, in the given circuit, the current flowing through the circuit can be found by using the above equation.
To know more about electrical circuit visit :
https://brainly.com/question/29761561
#SPJ11
What evidence did Wegener use to support his hypothesis of continental drift?
Question 19 options:
sea-floor spreading
paleoclimatic data
polar reversals
transform fault boundaries
What evidence did Wegener use to support his hypothesis of continental drift?
Question 19 options:
sea-floor spreading
paleoclimatic data
polar reversals
transform fault boundaries
Alfred Wegener used paleoclimatic data, such as plant fossils, to support his hypothesis of continental drift.
What is the continental drift theory? Continental drift is a geological theory that suggests that the Earth's continents were once connected as one huge landmass, which later separated and drifted to their current positions over millions of years. Wegener introduced the theory of continental drift in the early 20th century. However, his theory was met with criticism because he could not explain how the continents moved over time. Wegener used paleoclimatic data and fossil evidence to support his theory that the continents were once joined. Paleoclimatic data are ancient climate data that provide information about the Earth's past climate.
Wegener used plant and animal fossils as evidence to suggest that the continents were once connected. For instance, the fossils of the Mesosaurus, a freshwater reptile, were found in South America and Africa, and Wegener used this as evidence to support his theory that the continents were once connected. In addition, Wegener used other paleoclimatic data, such as glacial tillites, to suggest that the continents were once covered with ice sheets. What is Sea-floor spreading? Sea-floor spreading is a geological process where new oceanic crust is created as two plates move apart. Sea-floor spreading occurs at mid-ocean ridges where magma rises up from the mantle to create new oceanic crust. As the plates move away from each other, they carry the newly formed crust with them. This process of sea-floor spreading is driven by plate tectonics and is one of the main pieces of evidence supporting the theory of continental drift.
To know more about continental drift, visit:
https://brainly.com/question/15187534
#SPJ11
A 2.00−nF capacitor with an initial charge of 5.61μC is discharged through a 2.69-k Ω resistor. (a) Calculate the current in the resistor 9.00μs after the resistor is connected across the terminals of the capacitor. (Let the positive direction of the current be define such that dtdQ>0.) (b) What charge remains on the capacitor after 8.00μs ? ∣μC (c) What is the (magnitude of the) maximum current in the resistor? A
a) The current in the resistor 9.00μs after it is connected across the terminals of the capacitor is 1.04 A.
b) The charge remaining on the capacitor after 8.00μs is approximately 1.90 μC.
c) The magnitude of the maximum current in the resistor is approximately 1.04 A.
(a) To calculate the current in the resistor 9.00μs after it is connected across the terminals of the capacitor, we can use Ohm's Law. Ohm's Law states that current (I) is equal to voltage (V) divided by resistance (R). In this case, the voltage across the resistor is the voltage across the capacitor, which can be calculated using the formula Q/C, where Q is the charge on the capacitor and C is the capacitance.
Capacitance (C) = 2.00-nF = 2.00 × 10^(-9) F
Charge (Q) = 5.61 μC = 5.61 × 10^(-6) C
Resistance (R) = 2.69-kΩ = 2.69 × 10^3 Ω
First, calculate the voltage (V) across the resistor:
V = Q/C = (5.61 × 10^(-6) C) / (2.00 × 10^(-9) F) = 2805 V
Next, use Ohm's Law to calculate the current (I) in the resistor:
I = V/R = 2805 V / (2.69 × 10^3 Ω) = 1.04 A (to three significant figures)
Therefore, the current in the resistor 9.00μs after it is connected across the terminals of the capacitor is 1.04 A.
(b) To calculate the charge remaining on the capacitor after 8.00μs, we need to use the formula for the charge on a capacitor discharging through a resistor:
Q(t) = Q0 * e^(-t/RC)
Where:
Q(t) is the charge at time t
Q0 is the initial charge on the capacitor
R is the resistance
C is the capacitance
t is the time
Initial charge (Q0) = 5.61 μC = 5.61 × 10^(-6) C
Resistance (R) = 2.69-kΩ = 2.69 × 10^3 Ω
Capacitance (C) = 2.00-nF = 2.00 × 10^(-9) F
Time (t) = 8.00 μs = 8.00 × 10^(-6) s
Using the formula:
Q(t) = (5.61 × 10^(-6) C) * e^(-8.00 × 10^(-6) s / ((2.69 × 10^3 Ω) * (2.00 × 10^(-9) F)))
Calculating this expression gives us:
Q(t) ≈ 1.90 μC
Therefore, the charge remaining on the capacitor after 8.00μs is approximately 1.90 μC.
(c) To find the magnitude of the maximum current in the resistor, we can use the formula:
Imax = V0/R
Where:
Imax is the maximum current
V0 is the initial voltage across the capacitor (which is equal to the initial charge divided by the capacitance)
R is the resistance
Initial charge (Q0) = 5.61 μC = 5.61 × 10^(-6) C
Capacitance (C) = 2.00-nF = 2.00 × 10^(-9) F
Resistance (R) = 2.69-kΩ = 2.69 × 10^3 Ω
Calculate the initial voltage (V0) across the capacitor:
V0 = Q0/C = (5.61 × 10^(-6) C) / (2.00 × 10^(-9) F) = 2805 V
Now, calculate the maximum current (Imax) in the resistor:
Imax = V0/R = 2805 V / (2.69 × 10^3 Ω) ≈ 1.04 A
Therefore, the magnitude of the maximum current in the resistor is approximately 1.04 A.
learn more about current
https://brainly.com/question/1100341
#SPJ11
Thevenin and Norton Equivalent Circuit Transformations are only applicable on a. circuits with frequency dependant sources b. circuits with frequency independent sources c. neither
Only circuits with frequency-independent sources are suitable for the Thevenin and Norton equivalent circuit transformations.Option B is correct.
Both DC and AC circuits can benefit from the Thevenin and Norton transformation. The sources in DC circuits are frequency-dependent. The circuit's elements—capacitor and inductor—depend on the source's frequency for AC sources. Therefore, both thevenin and Norton can be utilized.
Using simple transformations and the application of fundamental circuit theorems, the circuit transformation method evaluates amplifier circuit parameters (gain, input, and output resistances). The process of converting voltage sources into current sources and vice versa using Thévenin's theorem and Norton's theorem, respectively, simplifies a circuit solution, particularly when using mixed sources.
You can transform a voltage source into a current source or the other way around with source transformation. A method for streamlining a circuit is it. The theorems of Thévenin and Norton serve as the foundation for the approach.
Learn more about Circuit transformation:
brainly.com/question/31417855
#SPJ4
The acceleration of a particle is given by \( a=3 t-18 \), where \( a \) is in meters per second squared and \( t \) is in seconds. Determine the velocity and displacement as functions of time. The in
To determine the velocity and displacement as functions of time, we have to integrate the given acceleration with respect to time.
Velocity
Integrating the given acceleration with respect to time, we get
[tex]$$v(t) = \int a(t) \, dt = \int (3t - 18) \, dt = t^2 - 6t + C$$$C$[/tex]is the constant of integration.
The velocity of the particle as a function of time is given by
[tex]$$v(t) = t^2 - 6t + C$$[/tex]
Displacement
To determine the displacement of the particle, we have to integrate the velocity of the particle with respect to time.
Integrating v(t) with respect to time, we get
[tex]x(t)=∫v(t)dt=∫(t 2 −6t+C)dt= 3t 3 −3t 2 +Ct+D[/tex]
where D is another constant of integration.
The displacement of the particle as a function of time is given by
[tex]x(t)= 3t 3 −3t 2 +Ct+D[/tex]
Initial Conditions
The initial conditions are the values of v(t) and x(t) at a specific time[tex]t 0[/tex]
We can use these conditions to determine the values of C and D.
For example, let's say that v(0)=10 and x(0)=0. Substituting these values into the equations for v(t) and x(t), we get
[tex]$10 = C$0 = \frac{0}{3} - 3 \cdot 0 + C \cdot 0 + D$$D = 0$[/tex]
Therefore, the constants of integration are C=10 and D=0.
To know more about displacement visit:
https://brainly.com/question/11934397
#SPJ11
Answer the following questions based upon the video: 1. Why should a student always turn off the power supply before altering their circuit? 2. What is the purpose of the 'output enable' function of the power supply? 3. What is the effect of having the current limit control set too low? 4. What is a voltmeter doing when it is performing a "DC" voltage measurement? 5. What is the relationship between which way around the leads of a voltmeter are used (ie, red vs. black leads) and the sign on the numerical value of the measured voltage as seen on the voltmeter display? (a diagram helps!) Ans: 3. Single Subscript Voltage Label 4. Explain the meaning of a 'component voltage label". Give an example in the form of a properly labeled resistor voltage: Ans: This voltage label describes the voltage based upon the component being measured. 5. Explain the meaning of a 'double subscript voltage label'. 6. Explain the meaning of a 'single subscript voltage label'.
The red lead of a voltmeter is always connected to the positive end of the circuit, and the black lead is connected to the negative end of the circuit. If the red lead is connected to the negative end of the circuit, the voltmeter will show a negative value.
1. Why should a student always turn off the power supply before altering their circuit?
It is always recommended to turn off the power supply before altering their circuit because it can cause a short circuit. The short circuit may cause damage to the components and even the power supply.
2. What is the purpose of the 'output enable' function of the power supply?
The 'output enable' function of the power supply is used to turn the voltage or current output on or off. It is a safety feature that helps to protect the device from electrical surges.
3. What is the effect of having the current limit control set too low?
When the current limit control is set too low, it can lead to insufficient current being supplied to the device, causing it to malfunction.
4. What is a voltmeter doing when it is performing a "DC" voltage measurement?
When a voltmeter is performing a "DC" voltage measurement, it is measuring the average value of the voltage over time.
5. What is the relationship between which way around the leads of a voltmeter are used (i.e., red vs. black leads) and the sign on the numerical value of the measured voltage as seen on the voltmeter display?
The red lead of a voltmeter is always connected to the positive end of the circuit, and the black lead is connected to the negative end of the circuit. If the red lead is connected to the negative end of the circuit, the voltmeter will show a negative value. If the black lead is connected to the positive end of the circuit, the voltmeter will also show a negative value. Thus, it is essential to connect the voltmeter leads correctly.
A component voltage label describes the voltage based on the component being measured. For example, a properly labeled resistor voltage is given as VR1 (meaning voltage across resistor 1). Double subscript voltage label refers to the voltage at a node or between two components. It is written as VA,B or VB-A. Single subscript voltage label refers to the voltage at a component and is written as VA.
To know more about surges visit:
https://brainly.com/question/29672300
#SPJ11
A simplified model of hydrogen bonds of water is depicted in the figure as linear arrangement of point ...12 charges. The intra molecular distance between qı and 92, as well as qs and qs is 0.10 nm (represented as thick line). And the shortest distance between the two molecules is 0.17 nm (q2 and qs, inter-molecular bond as dashed line). The elementary charge e = 1.602 x 10-1°C. Midway OH -0.35€ H +0.356 OH-0.35e H +0.35€ 91 42 93 7 Fig. 2 (a) Calculate the energy that must be supplied to break the hydrogen bond (midway point), the elec- trostatic interaction among the four charges. (b) Calculate the electric potential midway between the two H2O molecules.
The energy required to break the hydrogen bond at the midway point can be calculated using the formula for electrostatic interaction. The electric potential midway between the two H2O molecules can also be determined using the given charges and distances.
(a) To calculate the energy required to break the hydrogen bond at the midway point, we need to determine the electrostatic interaction among the four charges involved. The charges given in the figure are -0.35e, +0.356e, -0.35e, and +0.35e. We can use the formula for the electrostatic potential energy:
Energy = k * q1 * q2 / r
Where k is the Coulomb constant (8.988 × 10^9 Nm^2/C^2), q1 and q2 are the charges, and r is the distance between them. In this case, q1 and q2 are the charges at the midway point (-0.35e and +0.356e) and the distance between them is 0.10 nm. Plugging in the values, we get:
Energy = (8.988 × 10^9 Nm^2/C^2) * (-0.35e) * (+0.356e) / (0.10 nm)
(b) To calculate the electric potential midway between the two H2O molecules, we can use the formula for electric potential:
Electric potential = k * q / r
Where k is the Coulomb constant, q is the charge, and r is the distance. In this case, the charge q is the sum of the charges at the midway point (-0.35e and +0.35e) and the distance r is 0.10 nm. Plugging in the values, we get:
Electric potential = (8.988 × 10^9 Nm^2/C^2) * (-0.35e + 0.35e) / (0.10 nm)
Learn more about energy
brainly.com/question/1932868
#SPJ11
A 0.25-kg block oscillates linearly on the end of the spring with a spring constant of 160 N/m. If the system has an energy of 5 J, then the magnitude of the amplitude of the oscillation is: .........m, round to two decimal places.
The magnitude of the amplitude of the oscillation is 0.62 m.
Given:
Mass of block, m = 0.25kg
Spring constant, k = 160 N/m
Energy, E = 5 J
Amplitude, A = ?
Let's calculate the magnitude of the amplitude of the oscillation.The total energy of the system is the sum of kinetic and potential energies. Hence,
E = K + PE
where K is the kinetic energy and PE is the potential energy.
We know that the potential energy for a spring is given as;
PE = (1/2)kA²
Also, the kinetic energy of a block is given as;
K = (1/2)mv²
where v is the velocity of the block at any time. Now the velocity can be written in terms of amplitude and time period. Therefore,
K = (1/2)mv² = (1/2)kA²sin²(ωt)
Therefore,The total energy of the system can be expressed as:
E = (1/2)kA² + (1/2)kA²sin²(ωt)
On simplification, the maximum value of E will occur at t = 0.
Substituting values in the equation;
E = (1/2)kA²
∴5 J = (1/2) × 160 N/m × A²
∴A = 0.5 √(5/16)
= 0.62 m (rounded to two decimal places)
Hence, the magnitude of the amplitude of the oscillation is 0.62 m.
To know more about amplitude visit:
https://brainly.com/question/32825354
#SPJ11
Actuators and transducers are both examples of sensors: Select one: O a True Ob. False
Actuators and transducers are both examples of sensors: False.Actuators and transducers are not both examples of sensors. The statement is false.
Actuators are devices that are used to convert electrical or other types of energy into mechanical motion. The most common example of an actuator is a motor, which converts electrical energy into rotational motion.Transducers are devices that are used to convert one form of energy into another. Some common examples of transducers include microphones, which convert sound energy into electrical signals, and thermometers, which convert temperature into electrical signals.
Sensors, on the other hand, are devices that are used to detect or measure a physical quantity and convert it into an electrical signal. Examples of sensors include temperature sensors, pressure sensors, and light sensors.
To know more about Actuators visit:
https://brainly.com/question/12950640
#SPJ11
Use the following data to calculate the binding energy per nucleon in MeV of the Rhodium-103 nuclide 103 Mass of Rh atom = 102.905503 u Mass of proton = 1.007276 u Mass of neutron=1.008664 u Mass of electron= 0.00054858 1 u = 931.494 MeV
The following data is given Mass of Rh atom = 102.905503 u, Mass of proton = 1.007276 u, Mass of neutron = 1.008664 u and 1 u = 931.494 MeV. The first step in calculating the binding energy per nucleon in MeV of the Rhodium-103 nuclide is to determine the number of nucleons in the Rhodium-103 nuclide.How to determine the number of nucleons in the Rhodium-103 nuclide?Rhodium-103 has 45 protons since the atomic number is 45. Since the mass number (protons + neutrons) is given as 103, the number of neutrons can be calculated as follows:
103 - 45 = 58Therefore, the number of nucleons in Rhodium-103 nuclide is 103.Binding energy is the difference between the sum of the masses of nucleons and the mass of the nucleus.The mass of nucleons is the sum of the mass of protons and neutrons.Mass of nucleons = 45 x (mass of proton) + 58 x (mass of neutron) Mass of nucleons = (45 x 1.007276) + (58 x 1.008664) = 102.47171 uThe mass defect is the difference between the mass of nucleons and the mass of the nucleus.Mass defect = mass of nucleons - mass of nucleusMass defect = 102.47171 - 102.905503 = -0.433793 uThe negative sign indicates that the mass of the nucleus is less than the mass of the nucleons. The mass defect can be converted into binding energy using Einstein's equation, E = mc².Binding energy (BE) = Mass defect × c²BE = (-0.433793 u) × (931.494 MeV/u) = -404.938 MeVThe binding energy per nucleon (BEPN) can be calculated by dividing the binding energy by the number of nucleons.Binding energy per nucleon (BEPN) = Binding energy / Number of nucleonsBEPN = (-404.938 MeV) / (103) = -3.9333 MeVTherefore, the binding energy per nucleon in MeV of the Rhodium-103 nuclide is -3.9333 MeV.
About ProtonThe proton is a subatomic particle, symbol p or p⁺, with a positive electric charge +1e elementary charge and slightly less mass than a neutron. Protons and neutrons, each with a mass of about one atomic mass unit, are collectively referred to as "nucleons". heavier than electrons. Protons are so deep in the atomic nucleus that they cannot be disturbed by particles outside the atom.
Learn More About Proton at https://brainly.com/question/1805828
#SPJ11
fullt explain evryhting please and thank you:)
1. Using the example from class. find the value of the capacitance reactance being used when the power factor given is \( 0.95 \). Show: (a) Power factor angle (b) Total current (c) Current of the cap
In this question, we are given the power factor as 0.95. We need to find the capacitance reactance using the given values of power factor, power factor angle, total current, and current of the cap. We will use the following formulas to solve this problem. `
cosθ = P/S, sinθ = Q/S, tanθ = Q/P, Xc = V/Ic`.Here, θ is the power factor angle, P is the real power, Q is the reactive power, S is the apparent power, Xc is the capacitance reactance, V is the voltage, and Ic is the current of the cap. Given, Power factor = 0.95(a) Power factor angle cosθ = 0.95 => θ = cos⁻¹ (0.95) = 18.19°(b) Total currentWe know that `cosθ = P/S`. Here, S = VIcosθ. Thus, `I = S/V = P/(Vcosθ)`Substituting the values, we get `I = 2 kW / (220 V × 0.95) = 9.24 A`Therefore, the total current is 9.24 A.(c)
Current of the capWe know that `tanθ = Q/P`. Here, Q = PSinθ. Also, we know that `Xc = V/Ic`. Thus, `Ic = V/Xc`.Substituting the values, we get `Ic = 220 V / Xc`Also, `Q = Ptanθ = P × tan (18.19°) = 0.348 P`.Thus, `Ic = Q / Xcω` and `I = √(Ic² + Itotal²)`Substituting the values, we get `9.24 = √(Ic² + (0.348 × 2 kW / 220 V)²)`Solving for Ic, we get `Ic = 2.2 A`.Therefore, the current of the cap is 2.2 A.
To know more about power visit:
https://brainly.com/question/29575208
#SPJ11
1- Define the following: The polarizability - Polar molecules - Nonpolar molecules - Induced dipoles - Ferroelectric materials. 2- Deduce the Clausius-Mossotti equation. 3- Compute the polarizability of an atom, where the charge of the nucleus is (Ze) and the total charge of electrons (-Ze). 4- A point charge q is situated a large distance r from a neutral atom of polarizability a. Find the force of attraction between them. 5- Deduce the Langevin-Debye equation for polar molecules.
1- Polarizability: It is the tendency of a molecule or atom to become polarized when exposed to an electric field. Polar molecules: Molecules that have a positive or negative electrical charge at one end. Nonpolar molecules: Molecules that lack an electrical charge. Induced dipoles: When an electric field is applied to a nonpolar molecule, an induced dipole is formed.
Ferroelectric materials: Materials that exhibit spontaneous electric polarization in the absence of an electric field.
2- Clausius-Mossotti Equation
The Clausius-Mossotti equation can be expressed as:
(ε - 1) / (ε + 2) = (4πNa³α) / 3
The Clausius-Mossotti equation relates the dielectric constant (ε) of a substance to its polarizability (α). It provides a quantitative estimate of the polarizability of a molecule.
3- Computation of Polarizability
Polarizability of an atom can be computed using the following equation:
α = (1/6) × (e / ε₀) × (2a² + 3r²)
Where,α = polarizability of an atom
e = charge of the nucleus
r = distance between the electron and the nucleus
a = radius of the electron
ε₀ = permittivity of free space
4- Force of Attraction
The force of attraction (F) between a point charge (q) and a neutral atom of polarizability (a) can be computed using the following equation:
F = (q² / 4πε₀r²) × (α / 3)
When an electric field is applied to a nonpolar molecule, an induced dipole is formed. The induced dipole creates a temporary dipole, which creates an attractive force between the polar molecule and the point charge.
5- Langevin-Debye Equation
The Langevin-Debye equation can be expressed as:
(ε - ε₀) / (ε + 2ε₀) = 4πNpα / 3kT
The Langevin-Debye equation relates the dielectric constant (ε) of a substance to its polarizability (α), temperature (T), and particle density (Np). It is used to describe the behavior of polar molecules.
Therefore, the polarizability is the tendency of an atom or molecule to become polarized when exposed to an electric field. Polar molecules have a positive or negative electrical charge at one end while nonpolar molecules lack an electrical charge. Induced dipoles are formed when an electric field is applied to a nonpolar molecule. Ferroelectric materials exhibit spontaneous electric polarization in the absence of an electric field. The Clausius-Mossotti equation relates the dielectric constant (ε) of a substance to its polarizability (α). The polarizability of an atom can be computed using the formula.
The force of attraction (F) between a point charge (q) and a neutral atom of polarizability (a) can be computed using a formula. The Langevin-Debye equation relates the dielectric constant (ε) of a substance to its polarizability (α), temperature (T), and particle density (Np).
To know more about Polarizability, visit:
https://brainly.com/question/31842978
#SPJ11
An ultracentrifuge accelerates from rest to 106,000rpm in 2.10 min. What is its angular acceleration in rad/s
2
. (You do not need to enter any units.) rad/s
2
Tries 0/10 What is the tangential acceleration of a point 10.0 cm from the axis of rotation? Tries 0/10 What is the radial acceleration (in m/s
2
) of a point 10.00 cm at full rpm? (You do not need to enter any units.) m/s
2
Tries 0/10 What is the radial acceleration in multiples of g of this point at full rpm? Tries 0/10
When the engine is running at maximum speed, we may calculate the angular acceleration, tangential acceleration, radial acceleration, and radial acceleration in multiples of (g).
To find the angular acceleration of the ultracentrifuge, we can use the equation:
[tex]\[\text{{Angular acceleration}} (\alpha) = \frac{{\text{{Change in angular velocity}}}}{{\text{{Change in time}}}}\][/tex]
The change in angular velocity can be calculated by converting the given final angular velocity from rpm to rad/s and subtracting the initial angular velocity, which is 0 rad/s since it starts from rest.
The change in time is given as 2.10 min, which we need to convert to seconds.
To find the tangential acceleration of a point 10.0 cm from the axis of rotation, we can use the formula:
[tex]\[\text{{Tangential acceleration}} (a_t) = r \cdot \alpha\][/tex]
where [tex]\(r\)[/tex] is the distance from the axis of rotation. In this case, [tex]\(r = 10.0 \, \text{cm}\)[/tex] or [tex]\(0.10 \, \text{m}\)[/tex] (after converting to meters).
The radial acceleration of a point at a distance of 10.00 cm at full rpm is given by:
[tex]\[\text{{Radial acceleration}} (a_r) = r \cdot \omega^2\][/tex]
where [tex]\(\omega\)[/tex] is the angular velocity in rad/s. We can convert the given rpm value to rad/s and substitute it into the equation.
To find the radial acceleration in multiples of \(g\) at full rpm, we divide the radial acceleration by the acceleration due to gravity [tex](\(g \approx 9.8 \, \text{m/s}^2\))[/tex] and express it as a ratio.
By calculating these values using the given information, we can determine the angular acceleration, tangential acceleration, radial acceleration [tex](in m/s\(^2\))[/tex], and the radial acceleration in multiples of \(g\) at full rpm.
To learn more about radial acceleration
https://brainly.com/question/14071327
#SPJ11
A circuit consisting of a 20 ohm resistor, 20 mH inductor and a 100 microfarad capacitor in series is connected to a 200 V d.c supply. Assume that the capacitor is initially uncharged, determine the instantaneous expression for i. circuit current ii. voltage across the resistor iii. voltage across the inductor iv. voltage across the capacitor A circuit consisting of a 20 ohm resistor, 20 mH inductor and a 100 microfarad capacitor in series is connected to a 200 V d.c supply. Assume that the capacitor is initially uncharged, determine the instantaneous expression for i. circuit current ii. voltage across the resistor iii. voltage across the inductor iv. voltage across the capacitor
The instantaneous voltage across the inductor is:VL = 400 e^(-100t) sin(100t) Volts. The instantaneous voltage across the capacitor is given as: Vc = 0 V as it is initially uncharged.
Given circuit diagram is shown below, Consider that the current flowing in the circuit at any instant of time 't' is 'i' amperes. Circuit diagram is shown below: Initially, it is given that the capacitor is uncharged. Therefore, voltage across the capacitor is zero volts at t = 0.
Hence, the instantaneous voltage across the capacitor at any time 't' will be:Vc = 0 V
Let's consider the instantaneous voltage across the inductor is 'VL' and instantaneous voltage across the resistor is 'VR'.By using Kirchhoff's Voltage Law (KVL) in the above circuit we get:V = VL + VR + Vc
Where V is the potential difference provided by DC voltage source. So, we can write the equation of voltage across the inductor as: VL = L di/dt
The equation of voltage across the resistor is: VR = iR
By substituting the above equations in KVL we get:V = L di/dt + iR + 0V = L (d^2i/dt^2) + R(di/dt) + i (1)By taking Laplace transform on both sides, we get: V(s) = L s^2 I(s) + R s I(s) + I(s)
Solving the above equation for I(s), we get: I(s) = V(s) / (L s^2 + R s + 1)
In order to obtain the time domain expression, we take the inverse Laplace transform on I(s) which is given as: i(t) = L^-1{V(s) / (L s^2 + R s + 1)}
The expression for the instantaneous circuit current is: i(t) = (200/L) {1 - cos(100t)} e^(-100t) amperes
The expression for voltage across the resistor is: VR = iR
By substituting the value of 'i' we get, VR = 20 i(t)
Volatge across the resistor at any time t is given as: VR = (4000/L) {1 - cos(100t)} e^(-100t) Volts
The expression for voltage across the inductor is: VL = L (di/dt)
By substituting the value of 'i' we get, VL = 20 * (d/dt) i(t)
Volatge across the inductor at any time t is given as: VL = 400 e^(-100t) sin(100t) Volts
Therefore, the instantaneous voltage across the inductor is:VL = 400 e^(-100t) sin(100t) Volts.
The instantaneous voltage across the capacitor is given as: Vc = 0 V as it is initially uncharged.
To learn more about capacitor visit;
https://brainly.com/question/31627158
#SPJ11
