The triangulation method is the process used to determine the width of a large river.
Find the bearing from A to C. and find the distance from A to B?From the starting point to the finishing point, draw a line. Take a clockwise measurement of the angle between this line and the north line. As an illustration, the bearing from A to B is 100°. The angle between North and B is shown here.
The length of the river is equal to the tangent of the angle multiplied by the distance between the two points on your side of the waterway. Any two points on your riverbank can be used to solve this as well.
By deducting the bearing angle from 90 degrees, you can convert the bearing angle to degrees of a standard angle. If your final result is negative, add 360°; if it is positive but more than 360°, deduct 360°.
To learn more about distance refers to:
brainly.com/question/26550516
#SPJ4
how does the process of deforestation affect soil?
Deforestation is When forests are destroyed, the land is left unprotected and exposed to the weather, making it susceptible to being washed and blown away.
What impact does forest loss have on the planet?Carbon dioxide is absorbed and stored by trees. When forests are cut down or even just disturbed, carbon dioxide as well as other greenhouse gases are released. Around 10% of global warming is caused by the destruction and loss of forests. If we don't put an end to deforestation, there is just no way that we can combat the climate issue.
What are the causes of deforestation?The large-scale removal removing trees in forests (or other places) to make way for human activity is known as deforestation. It poses a major environmental risk since it may lead to the extinction of species, destruction of natural ecosystems, and disturbances in the water.
To know more about deforestation visit:
https://brainly.com/question/11697527
#SPJ4
how do spies use constructive and destructive interference of waves?
When two waves cross each other in a way that it combine to form a larger wave, this is known as constructive interference.When waves overlap in a way that they cancel one another out, destructive interference results.
What practical applications of destructive interference exist?Destructive interference is a technique used by engineers and scientists to lower levels of background noise and sound.The contemporary electronic automobile muffler is one illustration of this.The sound produced by this gadget, which senses the sound traveling down the exhaust pipe, has the opposite phase to the original sound.
How do waves become beneficial or harmful?Backwashes from destructive waves are more powerful than swashes.Erosion results from the powerful backwash pulling soil away from the beach and into the water.Contrarily, constructive waves are low intensity waves that cause material to accumulate along the shoreline.
To know more about interference of waves visit:
https://brainly.com/question/16622714
#SPJ4
Anu copied the formula =$A$3*$B$1 from cell A1 to B5. How will the formula look like in
cell B5?
(a) =$B$7*$C$5 (b) =$C$7*$B$5 (c) =$C$5*$B$7 (d) =$A$3*$B$1
Answer:
=$A$3*$B$1
Explanation:
Since cells involved in the formula are absolute row and column because of the $ sign on the row letter and column number for both, this formula will not changed when it is copied to any new location on the worksheet
You are reaching an intersection, and trees block your view to the side for the last 100 feet before crossing. The intersection is considered:
"open"
"blind"
"blocked"
A concealed hazard may be present if your line of sight is impeded in the intersection or beyond. Adjust your vehicle's location or widen the following gap if other cars are obstructing your view while you are traveling through traffic so you can see to react.
If you are unable to see around an obstruction, you must slow down and be prepared to change positions until you can regain a clear line of sight to your intended route and target region. In a city or other metropolitan setting, you should always be watching for at least two blocks or two traffic signals ahead. You should always look at least three blocks or three traffic lights ahead when driving in a suburban region. You need to keep an eye at least a quarter of a mile ahead when driving in a rural area.
Learn more about target at:
https://brainly.com/question/28555725
#SPJ4
a) design seismic loads on a building generally decrease with increased weight/mass of the building because of the inertia of the building. true/false
The correct answer is false design seismic loads on a building generally decrease with increased weight/mass of the building because of the inertia of the building.
One of the fundamental ideas in earthquake engineering is seismic loading, which refers to applying a seismic oscillation on a structure. It occurs where a structure makes touch with the ground or with other buildings. After transforming the Total Seismic Weight into a horizontal direction by multiplying it by the seismic response coefficient Cs, the seismic load is determined. In order to simulate the seismic contribution of the slab weight and any extra dynamo loads, the computer will apply a diaphragm surface load.Because the earthquake load is a "dynamic load," it causes buildings to vibrate.
To learn more about seismic loads click the link below:
brainly.com/question/9645077
#SPJ4
A tape recorder company manufacture model A, B and C with profit contribution per unit R. 15, R. 40 and R. 60 repectively. The weekly minimum requirement for Model A i 25 unit, for model B i 130 unit and for Model C i 55 unit. A dozen of unit of model A require 4 hr. For manufacturing, 3 hr. For aembling and 1 hr. For packaging. The correponding figure for a dozen unit of model B are 2. 5, 4 and 2 and for a dozen unit of model C are 6, 9 and 4. The company ha available 130 hr. For manufacturing, 170 hr. For aembling and 52 hr. For packaging during coming week. Formulate thi problem a an LP model o a to maximize the total profit to the company
Let the number of tape recorder for model A be x1
Let the number of tape recorder for model B be x2
Let the number of tape recorder for model C be x3.
Let the maximum profit be Z
Which tape recorder is best?TASCAM.Zoom.Olympus and Sony.HomderFun.Zoom. Sony.
stereo recorder DR-05X Wireless digital sound recorder from ZHN.Digital voice recorder ICD-BX-140, model number V415131BU000.Mono Portable Voice Recorder ICD-PX370 H2N.
Do tape recorders still get created today?If you're seeking for something completely unique, there are now just two firms that continuously create reel-to-reel sound records, one was in Pennsylvania and one in France.These recorders are still available in certain larger local libraries and archives, but they are still quite rare.
To know more about tape recorder company visit:
https://brainly.com/question/14301549
#SPJ4
They system that control such boy process as harmonies balance’ temperature and width of blot vessels is called the
The system that controls processes such as balance of hormones, temperature, and the width of blood vessels is called the Autonomic Nervous System. This system is responsible for regulating the body's internal organs and maintaining homeostasis. It is divided into two branches: the sympathetic nervous system, which is responsible for the "fight or flight" response, and the parasympathetic nervous system, which is responsible for the "rest and digest" response. The autonomic nervous system controls functions such as blood pressure, heart rate, and digestion, among others.
Two 16-year-olds have challenged three 12-year olds to tug-of-war. They discover that the two teams are very evenly matched, and the rope does not move in either direction. The older contestants each exert a force of 75 lbs on the rope. Determine the following:a) Draw the free-body diagram of the entire rope.b) How much force is exerted by each of the younger contestants if they share the force equally?c) What is the force in segments a, b, c and d of the rope? (Hint: Draw the free-body diagrams to represent each of the segments)
The force excreted by each of the youngsters is found using equilibrium and is equal to 50lbs. And the force in each segment is shown in the free body diagram. Each of the segment is subjected to tensile forces.
What is force?A push or a pull that alters or tends to alter an object's uniform motion or state of rest, as well as altering an object's direction or shape, is referred to as force. It either accelerates objects or increases the pressure they are under. The interaction between two objects is, to put it simply, a push or a pull on the object. It is the fundamental driver of motion starting from stillness. It's measured in "Newtons" (N). Newton calculates the amount of force necessary to move, accelerate, or speed up an object. F = m.a is the fundamental formula, where m is the mass in kilograms and an is the acceleration in m/sec2. The unit of measurement could also be pounds.To know more about force visit:
brainly.com/question/13191643
#SPJ4
Maximize the Revenue There are n types of items in a shop, where the number of items of type i is denoted by quantity[i]. The price of the items is determined dynamically, where the price of the i th item is equal to the remaining number of items of type i . There are m customers in line to buy the items from the shop, and each customer will buy exactly one item of any type. The shopkeeper, being greedy, trfes to sell the items in a way that maximises revenue. Find the maximum amount the shopkeeper can earn by selling exactly m items to the customers optimally.
Subtract your costs from the possible sales and supply of your products to arrive at your maximum amount.
How do you calculate the maximum profit made?Subtract your costs from the possible sales and supply of your products to arrive at your maximum profit.In the event that increasing income is similar,In other words, by setting marginal revenue to zero, which occurs at the maximum level of output, one may find the quantity and price that maximises profits. When the total revenue curve reaches its maximum value, marginal revenue is equal to zero.The amount where the disparity between total revenue and total cost is greatest will yield the highest profit. A completely competitive company, such as the raspberry farm, can determine the amount of output that will yield the maximum level of profit based on its total revenue and total cost curves.To learn more about maximum amount refer to:
https://brainly.com/question/14737887
#SPJ4
assume that a two-dimensional (2d) array arr of string objects with 3 rows and 4 columns has been properly declared and initialized. which of the following can be used to print the elements in the four corner elements of arr ? group of answer choices system.out.print(arr[0, 0] arr[0, 3] arr[2, 0] arr[2, 3]); system.out.print(arr[1, 1] arr[1, 4] arr[3, 1] arr[3, 4]); system.out.print(arr[0][0] arr[0][3] arr[2][0] arr[2][3]); system.out.print(arr[0][0] arr[0][2] arr[3][0] arr[3][2]);
The elements of the array's four corner elements can be printed using the following.
System.out.print(arr[0][0] + arr[0][3] + arr[2][0] + arr[2][3]);
What does "array" mean?An array, a kind of data structure, is a group of items, each of which is identifiable from at least one the array's ends or key. A mathematical formula may identify the position of each element in an array given its index tuple.
In C, how is an array defined?Arrays are used to store several values in a single variable as opposed to having separate variables for each value. To create an array, specify the type of data (such as int) as well as the array name, both enclosed in square brackets.
To know more about array visit:
https://brainly.com/question/19570024
#SPJ4
phototransistors are becoming more common than photoresistors because silicon is more resistant to high temperatures and airborne contamination. this makes it ideal for new outdoor lighting control applications or to replace failed photoresistors. T/F
True, phototransistors are becoming more common than photoresistors because silicon is more resistant to high temperatures and airborne contamination.
What is a phototransistor?Phototransistors are electronic switching and power amplification components that rely on light to operate. When light hits the junction, it causes a return current proportional to its brightness. Phototransistors are often used to capture pulses of light and convert them into digital electrical signals.
Phototransistors have several key advantages that set them apart from other optical sensors. Some of them are listed below
A phototransistor produces a higher current than a photodiode.Phototransistors are relatively cheap, simple, and small enough to fit several on a single integrated computer chip. Phototransistors are very fast and can output almost instantly.A phototransistor produces a voltage that a photoresistor cannot produce.To know more about phototransistors, visit :
https://brainly.com/question/30266054
#SPJ4
the statue of liberty's pedestal is concrete and at the time it was built was one of the largest pours ever attempted. the builders wanted to use concrete, instead of the granite called for in the design, to prove that it could be done. True or false?
To demonstrate that it could be done, the builders chose to utilize concrete rather than the granite specified in the plan. True
Is concrete used to build the Statue of Liberty?For its numerous products, cement received numerous national and international prizes for innovation. They agreed to supply 8,000 barrels of Portland cement to the United States in 1886 as part of one of the largest contracts of their professional lives. This cement was used to build the base of the Statue of Liberty.
What does the Statue of Liberty's pedestal represent?The stone construction between the base of the statue and the old, star-shaped battle fort is referred to as the pedestal. It raises the statue and supports her at the same time. Tickets for pedestals provide you entry inside and access to the outside balcony that is located immediately beneath the statue's feet.
To know more about liberty's pedestal visit:-
https://brainly.com/question/15219437
#SPJ4
# Ex 1: Check if mtcars is a dataframe using is.data.frame(). mtcars is built in dataset. To access available datasets use data()
```{r}
is.data
```
# Ex 2: Create a matrix "mat" and convert it into a dataframe:
```{r}
mat <- matrix(1:25,nrow = 5)
```
# Ex 3: Set the built-in data frame mtcars as a variable df.
```{r}
df <-
```
# Ex 4: Select the rows where all cars have 6 cylinders (cyl column)
```{r}
```
####################################################################################
############################ R Function Exercises ###############################
####################################################################################
# Ex 5: Create a function that will return the product of two integers.
```{r}
prod <- function(num1,num2){
.............
.............
}
prod(3,4)
```
# Ex 6: Create a function that accepts two arguments, an integer and a vector of integers. It returns TRUE if the integer is present in the vector, otherwise it returns FALSE. Make sure you pay careful attention to your placement of the return(FALSE) line in your function!
```{r}
num_check <- function(num,v){
.............
.............
}
num_check(2,c(1,2,3))
```
# Ex 7: Create a function that accepts two arguments, an integer and a vector of integers. It returns the count of the number of occurences of the integer in the input vector.
```{r}
num_count <- function(num,v){
.............
.............
}
num_count(2,c(1,1,2,2,3,3))
```
# Ex 8: We want to ship bars of aluminum. We will create a function that accepts an integer representing the requested kilograms of aluminum for the package to be shipped. To fullfill these order, we have small bars (1 kilogram each) and big bars (5 kilograms each). Return the least number of bars needed.
```{r}
bar_count <- function(pack){
.............
.............
}
bar_count(6)
bar_count(17)
```
# Ex 9: Create a function that accepts 3 integer values and returns their sum. However, if an integer value is evenly divisible by 3, then it does not count towards the sum. Return zero if all numbers are evenly divisible by 3. Hint: You may want to use the append() function.
```{r}
summer <- function(a, b, c){
.............
.............
}
summer(7,2,3)
summer(3,6,9)
summer(9,11,12)
```
# Ex 10: Create a function that will return TRUE if an input integer is prime. Otherwise, return FALSE. You may want to look into the any() function. There are many possible solutions to this problem.
```{r}
prime_check <- function(num) {
.............
.............
}
Most used R built-in data sets
mtcars: Motor Trend Car Road Tests
The data was extracted from the 1974 Motor Trend US magazine, and comprises fuel consumption and 10 aspects of automobile design and performance for 32 automobiles (1973–74 models)
Format
A data frame with 32 observations on 11(numeric) variables.
View the content of mtcars data set:
1. Loading
data("mtcars")
2. Print
head(mtcars)
## mpg cyl disp hp drat wt qsec vs am gear carb
## Mazda RX4 21.0 6 160 110 3.90 2.620 16.46 0 1 4 4
## Mazda RX4 Wag 21.0 6 160 110 3.90 2.875 17.02 0 1 4 4
## Datsun 710 22.8 4 108 93 3.85 2.320 18.61 1 1 4 1
## Hornet 4 Drive 21.4 6 258 110 3.08 3.215 19.44 1 0 3 1
## Hornet Sportabout 18.7 8 360 175 3.15 3.440 17.02 0 0 3 2
## Valiant 18.1 6 225 105 2.76 3.460 20.22 1 0 3 1
It contains 32 observations and 11 variables: # Number of rows (observations)
nrow(mtcars)
## [1] 32
[1] 32 # Number of columns (variables)
ncol(mtcars)
## [1] 11
If you want to learn more about mtcars, type this:
?mtcars
select head of mtcars data set
head(mtcars)
## mpg cyl disp hp drat wt qsec vs am gear carb
## Mazda RX4 21.0 6 160 110 3.90 2.620 16.46 0 1 4 4
## Mazda RX4 Wag 21.0 6 160 110 3.90 2.875 17.02 0 1 4 4
## Datsun 710 22.8 4 108 93 3.85 2.320 18.61 1 1 4 1
## Hornet 4 Drive 21.4 6 258 110 3.08 3.215 19.44 1 0 3 1
## Hornet Sportabout 18.7 8 360 175 3.15 3.440 17.02 0 0 3 2
## Valiant 18.1 6 225 105 2.76 3.460 20.22 1 0 3 1
select end of mtcars data set
tail(mtcars)
## mpg cyl disp hp drat wt qsec vs am gear carb
## Porsche 914-2 26.0 4 120.3 91 4.43 2.140 16.7 0 1 5 2
## Lotus Europa 30.4 4 95.1 113 3.77 1.513 16.9 1 1 5 2
## Ford Pantera L 15.8 8 351.0 264 4.22 3.170 14.5 0 1 5 4
## Ferrari Dino 19.7 6 145.0 175 3.62 2.770 15.5 0 1 5 6
## Maserati Bora 15.0 8 301.0 335 3.54 3.570 14.6 0 1 5 8
## Volvo 142E 21.4 4 121.0 109 4.11 2.780 18.6 1 1 4 2
summaries the data set
summary(mtcars)
## mpg cyl disp hp
## Min. :10.40 Min. :4.000 Min. : 71.1 Min. : 52.0
## 1st Qu.:15.43 1st Qu.:4.000 1st Qu.:120.8 1st Qu.: 96.5
## Median :19.20 Median :6.000 Median :196.3 Median :123.0
## Mean :20.09 Mean :6.188 Mean :230.7 Mean :146.7
## 3rd Qu.:22.80 3rd Qu.:8.000 3rd Qu.:326.0 3rd Qu.:180.0
## Max. :33.90 Max. :8.000 Max. :472.0 Max. :335.0
## drat wt qsec vs
## Min. :2.760 Min. :1.513 Min. :14.50 Min. :0.0000
## 1st Qu.:3.080 1st Qu.:2.581 1st Qu.:16.89 1st Qu.:0.0000
## Median :3.695 Median :3.325 Median :17.71 Median :0.0000
## Mean :3.597 Mean :3.217 Mean :17.85 Mean :0.4375
## 3rd Qu.:3.920 3rd Qu.:3.610 3rd Qu.:18.90 3rd Qu.:1.0000
## Max. :4.930 Max. :5.424 Max. :22.90 Max. :1.0000
## am gear carb
## Min. :0.0000 Min. :3.000 Min. :1.000
## 1st Qu.:0.0000 1st Qu.:3.000 1st Qu.:2.000
## Median :0.0000 Median :4.000 Median :2.000
## Mean :0.4062 Mean :3.688 Mean :2.812
## 3rd Qu.:1.0000 3rd Qu.:4.000 3rd Qu.:4.000
## Max. :1.0000 Max. :5.000 Max. :8.000
quantiles of dataset
quantile(mtcars$wt)
## 0% 25% 50% 75% 100%
## 1.51300 2.58125 3.32500 3.61000 5.42400
select quantiles by percent
To calculate the quantiles by percent:
quantile(mtcars$wt, c(.2, .4, .8))
## 20% 40% 80%
## 2.349 3.158 3.770
variance of weight
To calculate the variance of weight:
var(mtcars$wt)
## [1] 0.957379
Historgram
Histograms are a classic way to assess the shape of the distribution of a single variable.
To get the histogram of hp, the code below will produce a histogram:
hist(mtcars$hp)
We explored some of the common functions in R that I like to use to explore a data frame before I conduct any statistical analysis. We used the built-in data set mtcars to illustrate these functions.
To know more about data frame visit:
https://brainly.com/question/28448874
#SPJ4
technician a says gasoline and kerosene are typical cleaning agents used to clean hands of grease and other automotive chemicals. technician b says your hands are very porous and easily absorb solvents on contact. who is correct?
Technician B is correct who says that hands are very porous and can easily absorb solvents such as gasoline and kerosene so they should be avoid cleaning hands.
Solvents such as gasoline and kerosene may be used by workers to clean their skin or hands following contact with oily materials. However, this practice is not recommended, because it is well known that these solvents will defat the skin. So technician B is correct to state that hands are very porous and can easily absorb solvents so avoid using these solvents to clean hands.
In the contrast, technician A is not correct to say that kerosene and gasoline are typical cleaning agents to be used to clean hands of grease and other automotive chemicals.
To learn more about cleaning agents at
https://brainly.com/question/21104459
#SPJ4
A biomedical engineer poked some sensors into a single neuron (nerve cell) in a giant squid to
measure its electrical activity. The voltage signals coming out of the neuron are graphed below.
a) What is the approximate frequency of this signal in this time window? Show your
calculations.
b) How would the graph look different if the frequency was increased? Decreased?
A neurotransmitter, or chemical, is released by a presynaptic neuron (i.e., the sending neuron) and binds to a receptor on the surface of the postsynaptic neuron (i.e., the receiving neuron), which is the receiving neuron. Presynaptic terminals, which may branch to connect with numerous postsynaptic neurons, release neurotransmitters.
What is the Signal Transmission Within Nerve Cells ?Voltage differentials (also known as potentials) between the interior and exterior of the cell serve as the foundation for the signal-transmission mechanism within neurons. The most significant ions are calcium (Ca2+), potassium (K+), sodium (Na+), and chloride (Cl). This membrane potential is caused by the uneven distribution of electrically charged particles, or ions. Through certain protein channels in the cell membrane, ions move into and out of the cell. Neurotransmitters or modifications in the cell's membrane potential cause the channels to "open" or "shut." The ensuing redistribution of electric charge could change the voltage difference across the membrane. Depolarization is the process of reducing the voltage difference. An action potential, or impulse, will move along the neuron if depolarization rises over a particular threshold.It is prevented from propagating in any other direction except toward the axon tip by a number of processes. "Firing" is another word for the process of creating an action potential.To Learn more About neurotransmitter refer To:
https://brainly.com/question/840056
#SPJ1
a traffic engineer developed the continuous function r, graphed above, to model the rate at which vehicles pass a certain intersection over an 8-hour time period, where r(t) is measured in vehicles per hour and t is the number of hours after 6:00 am. according to the model, how many vehicles pass the intersection between time t
14400 vehicles pass the intersection between time t, according to the model.
Why do so many drivers run red lights?One of the main reasons motorists run red lights by accident is because they are distracted or not paying attention. Red light running has been linked to passengers, drowsiness, GPS, smartphones, and radios. 57% of motorists say they eat or drink while driving. Twenty-nine percent of drivers admit to texting while driving.
Which city has the most people who run red lights?According to the National Coalition for Safer Roads, Houston is the most dangerous city in the United States for running red lights, with 181 fatalities from 2004 to 2013. From 2004 to 2013, the fatalities caused by running red lights in US cities are depicted in this chart.
To know more about model visit :-
https://brainly.com/question/19426210
#SPJ4
what digit password may be set to prevent unauthorized operation of the yaesu ft-70dr?
A 4-digit password may be set to prevent unauthorized operation of the transceiver without permission.
what digit password may be set to prevent unauthorized operation ?It is a system created to stop unapproved access to or from a private network. So, Option 4 is the right choice. A firewall can be put into place as either hardware, software, or a hybrid of the two.
programme firewall: You can help protect your computer from unauthorised data entry and exit by installing a software firewall on it. Securing only the machine on which it is installed is the main objective of a software firewall. Many antivirus scanners come with a software firewall as standard equipment.
taking or requesting to "borrow" another employee's badge. Following another person through access doors in an attempt to "piggyback." using a colleague's password or login information to access a computer.
To learn more password refers to:
https://brainly.com/question/28114889
#SPJ4
By signing on the mailing list for NCAS, one can keep getting the information vulnerabilities, incidents, mitigation from US GovernmentUS-CERT ONIST CISCO
The purpose of mailing US-CERT Reason ---> CERT Alert is to notify owners and operators of critical infrastructure of threats.
What is the purpose of US CERT?US-CERT is in charge of analyzing and reducing cyber threats and vulnerabilities, disseminating information about cyber threat warnings, and coordinating activities related to incident response. US-CERT collaborates with state and local governments, international organizations, the private sector, the research community, and federal agencies.
How do cert notifications work?The purpose of an ICS-CERT Alert is to promptly notify owners and operators of critical infrastructure of threats or activities that have the potential to affect computing networks of critical infrastructure.
To know more about mailing visit :-
https://brainly.com/question/15710969
#SPJ4
What type of information is commonly included in the owner's manual that would be a benefit to the service technician?
O Maintenance items specifications
O Tire pressure monitoring system reset procedures
O Maintenance reminder light reset procedures
O All of the above
Maintenance reminder light reset procedures is a benefit to the service technician.
What is meant by technician?
Technicians are knowledgeable workers who are found in practically every field.Different systems and pieces of equipment are repaired, installed, replaced, and serviced. Technicians should be able to comprehend instructions and speak well because they frequently collaborate with other skilled individuals.A person knowledgeable in a specific technical subject or in mechanical or industrial processes. a person employed to perform practical work in a laboratory, technical school, or scientific facility.An individual with expertise in a technical procedure is referred to as a technician.It can take time, but in the end, it is a terrific feeling to find a solution to someone else's difficulty. It's Hard Work, But RewardingTo learn more about technician refer to
https://brainly.com/question/18428188
#SPJ1
Maintenance reminder light reset procedures is a benefit to the service technician.
What is meant by technician?Technicians are knowledgeable workers who are found in practically every field.
Different systems and pieces of equipment are repaired, installed, replaced, and serviced.
Technicians should be able to comprehend instructions and speak well because they frequently collaborate with other skilled individuals.
A person knowledgeable in a specific technical subject or in mechanical or industrial processes. a person employed to perform practical work in a laboratory, technical school, or scientific facility.
An individual with expertise in a technical procedure is referred to as a technician.
It can take time, but in the end, it is a terrific feeling to find a solution to someone else's difficulty. It's Hard Work, But Rewarding
To learn more about technician refer to
brainly.com/question/18428188
#SPJ1
Consider a wave that is traveling in the positive z direction, which is incident on a junction with another transmission line. The wave is on transmission line 1 in the region z 0, with characteristic impedance Zo1, and to the right of the junction (z> 0) is transmission line 2 with characteristic impedance Zo2. Assume for simplicity that the incident voltage wave has a voltage of 1.0 [V]. Solve for the reflected and transmitted voltages and currents on both sides of the junction. From this, show that the total current is continuous at the junction. Also show that the total power flowing in the z direction is the same on either side of the junction. Recall that the voltage transmission coefficient is related to the voltage reflection coefficient by Note that the total voltage and current on the left line (ine1) are found from summing the voltage and current for the incident and reflected waves, while the total voltage and current on the right line (line 2) are those of the transmitted wave. Also, note that power is given by P-VI, where Vand I are the total voltage and current in the time domain.
The correct answer is According to P = V I and P = V/I, the source's power (P) input to the circuit is determined.
P = E/t is the equation, where P stands for power, E for energy, and t for time in seconds. According to this equation, power is defined as the amount of energy consumed per unit of time. Ohm's Law states that the electrical current in a circuit may be estimated by dividing the voltage by the resistance in the first iteration of the calculation, I = V/R. In other words, the voltage and resistance are inversely related to the current and directly proportional to each other. Ohm's Law describes the connection between current, voltage, and resistance. This asserts that, given the temperature is constant, the current flowing in a circuit is directly proportional to the applied voltage and inversely proportional to the circuit resistance.
To learn more about circuit click the link below:
brainly.com/question/27206933
#SPJ4
start access. open the support ac financial services database from the data files. (if you did not previously complete the exercise, see your instructor for a copy of the modified database.)
A computer system can be accessed in one of three ways: Direct access, sequential indexing, and sequential access
How can I search a database in Access for data?Click Find in the Find group under the Home tab. The Find tab is chosen, and the Find and Replace dialogue box displays. Enter the value you wish to search for in the Find What box. Click the relevant link in the Look In list to alter the search field you wish to use or to search the full underlying table.A computer system can be accessed in one of three ways: Direct access, sequential indexing, and sequential access. It is the simplest method of access. One record at a time, the information in the data file is processed in sequence.To learn more about data files refer to:
https://brainly.com/question/29908028
#SPJ4
what is the key to preventing accidents in a welding shop
Answer: The key to prevent accidents in a welding shop are: Necessary protection must be taken while welding process otherwise it will harm the welder. Safety precautions must be taken. The safety precautions are mentioned on the manual of every equipment.
kg The Reynolds number, PVD/u is a very important parameter in fluid mechanics. Determine its value for ethyl alcohol flowing at a velocity of 2 m/s through a 5-in.-diameter pipe. Use u = 1.19 x 10-3 N.S and p = 789 m2 m3 PVD/=
The Reynolds number is used to get an understanding of the interaction between viscous forces, which cause the fluid to cease flowing because of its viscosity, and inertial forces, which keep moving according to Newton's first law - an item in motion continues in motion - in fluid flow.
By calculating the ratio of inertial and viscous forces, the Reynolds number (Re) can be used to forecast flow patterns in various fluid flow scenarios. Laminar (sheet-like) flow tends to dominate flows at low Reynolds numbers, whereas turbulent flow tends to dominate at high Reynolds numbers. A dimensionless metric called the Reynolds number makes it easier to forecast the behavior of flows. Laminar flow is indicated by a low Reynolds number, while turbulent flow.
Learn more about forecasts at:
https://brainly.com/question/24730207
#SPJ4
which type of shoring should be used to prevent vertical movement of a vehicle when its tires or suspension system cannot withstand g-loads without failure?
The correct answer is rolling shoring type of shoring should be used to prevent vertical movement of a vehicle when its tires or suspension system cannot withstand g-loads without failure.
To prevent damage to the aircraft's cargo floor, loading ramps, and airport parking lots, use rolling shoring. When transporting a vehicle across surfaces, this kind of shoring is employed to prevent damage (Figure 6-3). The deployment of the organic/attached troops by the deploying units is planned, organised, and carried out. Minimizing the amount of time a moving unit is not in use must be a top priority. used to prevent damage to the aircraft floor, aircraft ramps, and airfield parking ramps. - Lay down on the aircraft's ramp and floor when loading or unloading cargo. -Place throughout the whole path taken by the vehicle.
To learn more about rolling shoring click the link below:
brainly.com/question/4581001
#SPJ4
A programmer wants to determine whether a score is within 10 points of a given target. For example, if the target is 50, then the scores 40, 44, 50, 58, and 60 are all within 10 points of the target, while 38 and 61 are not.
Which of the following Boolean expressions will evaluate to true if and only if score is within 10 points of target ?
Selected Answer: [None Given]Answers:
(score ≤ target + 10) AND (target + 10 ≤ score)
(target + 10 ≤ score) AND (score ≤ target - 10)
(score ≤ target - 10) AND (score ≤ target + 10)
(target - 10 ≤ score) AND (score ≤ target + 10)
If and only if the score is within 10 points of the target, the following Boolean expressions will evaluate to true.
(target - 10 ≤ score) AND (score ≤ target + 10)
A logical statement that can only be either TRUE or FALSE is called a Boolean expression. Any form of data may be compared using boolean expressions as long as both portions of the expression use the same fundamental data type. Data can be tested to see if it is more than, equal to, or less than other data.
A Boolean expression can include Boolean information like the following:
the BOOLEAN values (YES and NO, and their synonyms, ON and OFF, and TRUE and FALSE)
variables or formulae in BOOLEAN
Boolean-results-producing functions
Calculated via comparison operators are BOOLEAN values.
Consider the following Boolean statement to be part of your code, for instance. genuine GT 20000
Learn more about Boolean expressions here:
https://brainly.com/question/27309889
#SPJ4
A first class lever in static equilibrium has a 50-lb resistance force and 15-lb effort force. The lever’s effort force is located 4 ft from the fulcrum. Calculate the length from the fulcrum to the resistance force.
a. 1.2 feet
b. 13.3 feet
c. 4 feet
d. 3.33 feet
In static equilibrium, a first-class lever has a resistance force of 50 lb and an effort force of 15 lb. The effort force of the lever is located 4 feet from the fulcrum. The length from the fulcrum to the resistance force is 1.2 feet.
AMA=F[tex]_{R}[/tex]/F[tex]_{E}[/tex]
=50 lb/15 lb
AMA=10/3≅3.3:1
[tex]M_{E} =M_{R}[/tex]
[tex]F_{E} *D_{E} =F_{R} *D_{R}[/tex]
(15 lb)*(4 ft)=(50 lb)D[tex]_{R}[/tex]
D[tex]_{R}[/tex]=(6/5)ft=1.2 ft
Statics is the branch of mechanics that studies forces acting on bodies in static or dynamic equilibrium. Static equilibrium is a state in which bodies are at rest; dynamic equilibrium is a state in which bodies move at a constant velocity (rectilinear motion). In both cases, the sum of the forces acting on them is zero.
Statics is the branch of mechanics that studies forces acting on bodies in static or dynamic equilibrium. Static equilibrium is a state in which bodies are at rest; dynamic equilibrium is a state in which bodies move at a constant velocity (rectilinear motion). In both cases, the sum of the forces acting on them is zero. Consider the following scenario: an athlete is standing on the ground.
Learn more about Static equilibrium here:
https://brainly.com/question/29316883
#SPJ4
architectural drawings that describe the layout and construction of a house are referred to as what...?
Architectural drawings that describe the layout and construction of a house are referred to as blueprints. The traditional name used to describe construction drawings. Civil plans. Drawings that show the location of the building on the side from aerial view, including contours, trees, construction features, and dimensions.
Which of the following is static characteristics of measurement?
Unwanted static traits in measurement systems include drift, static inaccuracy, dead zone, and non-linearity.
Which one of the following does not describe a measurement system's static characteristics?
Explanation:Sincerity is not a fixed quality.It is an element of an instrument's dynamic.In terms of measurements, fidelity relates to how accurate a number is when compared to a quantity that hasn't experienced any dynamic mistakes.
What qualities does measuring have?It offers a definition for each of the five key attributes of a measuring device: scale length, sensitivity, accuracy, "finesse," and response time.
To know more about measurement visit:
https://brainly.com/question/4725561
#SPJ4
Which of the following Belt Levels usually require a Six Sigma Project be completed before a Six Sigma Certification is awarded?A . White BeltB . Yellow BeltC . Green BeltD . Black BeltE . Master Black BeltF . None of the AboveG . All of the above
Prior to receiving a Six Sigma Certification, Belt Levels typically require the completion of a Six Sigma Project.
Is a project required for Six Sigma Black Belt?Examine the various roles, belts, and levels of Six Sigma. Note: To earn your Six Sigma Black Belt certification, you must complete at least one project and submit an affidavit for that project.
I should acquire which Six Sigma Belt first?Green Belt: serves as a fundamental introduction to Lean Six Sigma for novices. Belt Green: Intermediate program that teaches you how to work on company-wide process improvement projects. Brown Belt: Program of advanced training for project team management.
To know more about Six Sigma visit :-
https://brainly.com/question/30269340
#SPJ4
find the moment of inertia of a t section having a web and flang of 120 mm and 30mm about an x-x axis passing through the center of gravity
The moment of inertia of a t-section with a web and flang of 120 mm and 30 mm, respectively, about an x-x axis passing through the centre of gravity is: [tex]16 \mathrm{~cm}^4[/tex]
What is gravity?All the planets are maintained in their orbits around the sun by the force of gravity. Gravity comes in only one variety. There aren't any additional variations of gravity in the natural world. This implies that, depending on the masses of the two bodies and the separation between their centers, there is only one kind of gravitational force acting to draw them together. The weakest force known to exist in nature is gravity, which is a form of central force. Gravity is the force that a planet (or other entity) applies to other objects to pull them toward its centre.Second moment of area (M.I. ), also known as the moment of inertia of an area, is the total of the second moments of all elementary areas about an axis.
[tex]$\mathrm{I}=\sum\left(\mathrm{A} \times \mathrm{d}^2\right)[/tex]
Unit: [tex]$\mathrm{m}^4$[/tex]or [tex]$\mathrm{mm}^4$[/tex] or [tex]$\mathrm{cm}^4$[/tex]
Calculation:
Given,
b=3 cm, d=4 cm
A rectangle's moment of inertia about an axis parallel to its width and passing through its centre of gravity is
[tex]$& \mathrm{I}_{\mathrm{XX}}=\frac{\mathrm{bd}^3}{12} \\[/tex]
[tex]$& \mathrm{I}_{\mathrm{XX}}=\frac{3 \times 4^3}{12}=16 \\[/tex]
[tex]$& \therefore \mathrm{I}_{\mathrm{XX}}=16 \mathrm{~cm}^4[/tex]
The complete question is:
Find the moment of inertia of a t section having a web and flang of 120 mm and 30mm about an x-x axis passing through the center of gravity
To learn more about gravity, refer to:
https://brainly.com/question/13397785
#SPJ1