Using a raised cosine roll off Nyquist filter, a telephone line channel is equalized to allow bandpass data transmission over a frequency range of 400 to 3,600 Hz.
Appropriate values for the roll-off factor, absolute bandwidth, and 6-dB QAM signal bandwidth are chosen during the design of the filter.A 64-symbol QAM signaling scheme is also designed in this design. This scheme enables the transfer of data at a rate of 14,400 bits/s over the channel.The explanation:Raised cosine rolloff Nyquist filter is chosen to equalize the telephone line channel to enable bandpass data transmission over a frequency range of 400 to 3,600 Hz. The roll-off factor, absolute bandwidth, and 6-dB QAM signal bandwidth are parameters that must be determined in order to effectively design the filter. These values can be chosen in order to make sure that the filter is well suited for the specific requirements of the application.
Therefore, the appropriate values for the roll-off factor, absolute bandwidth, and 6-dB QAM signal bandwidth are chosen in order to design the raised cosine roll off Nyquist filter. Finally, a 64-symbol QAM signaling scheme is designed to enable the transfer of data at a rate of 14,400 bits/s over the channel.
To Know more about telephone visit:
brainly.com/question/32084449
#SPJ11
A 100 V, 60 Hz, 4 pole, single phase induction motor has the following parameters: R1 = R2 = 3 ohms, X1 = X2 = 3 ohms and Xm =70 ohms. We have core losses of 27 W and friction and vent losses of 15 W. For a slip of 11%,
calculate:
1. The impedance of the anterior branch
2. the impedance of the posterior branch
3. the total impedance
4. the input current module
5. the power developed
6.input power
7. power output
8. efficiency
In the given scenario of a single-phase induction motor, the following calculations need to be performed for a slip of 11%:
What calculations need to be performed for the given single-phase induction motor scenario?1. The impedance of the anterior branch: The anterior branch consists of the stator winding and its parameters. The impedance is given by Z1 = R1 + jX1, where R1 is the stator resistance and X1 is the stator reactance.
2. The impedance of the posterior branch: The posterior branch consists of the rotor winding and its parameters. The impedance is given by Z2 = R2/s + jX2, where R2 is the rotor resistance, X2 is the rotor reactance, and s is the slip.
3. The total impedance: The total impedance Z is the sum of the anterior and posterior branch impedances, i.e., Z = Z1 + Z2.
4. The input current module: The input current module can be calculated using Ohm's law, where Iin = V/Z, where V is the applied voltage.
5. The power developed: The power developed by the motor can be calculated as Pdev = 3 × V × Iin × (1 - s).
6. Input power: The input power is the product of the applied voltage and the input current module, Pin = V × Iin.
7. Power output: The power output of the motor is given by Pout = Pdev - Core losses - Friction and vent losses.
8. Efficiency: The efficiency of the motor is calculated as Efficiency = Pout / Pin.
By performing these calculations, the impedance values, input current, power developed, input power, power output, and efficiency of the motor can be determined for the given slip value of 11%.
Learn more about induction motor
brainly.com/question/32808730
#SPJ11
Consider a continuous LTI system: . Using a fourier transform,
find the output y(t) to the following input signal: x(t) = u(t).
Parameter u(t) is a unit step function
For the given continuous LTI system and the input signal x(t) = u(t), the output y(t) can be obtained using Fourier Transform.
Given system:Consider a continuous LTI system:y(t) - y(t - 2) + 3y(t - 4) - 3y(t - 5) = x(t) ---(1)Input signal:x(t) = u(t) ---(2)Fourier Transform of Equation (1):Y(ω)e^(-jωt) - Y(ω)e^(-jω(t - 2)) + 3Y(ω)e^(-jω(t - 4)) - 3Y(ω)e^(-jω(t - 5)) = X(ω)From equation (2), we can say that:X(ω) = 1/(jω) + πδ(ω)Using the above equations, we can get the output signal Y(ω) as:Y(ω) = [1/(jω) + πδ(ω)] / [1 - e^(-jωt) + 3e^(-jωt+2) - 3e^(-jωt+3)]The inverse Fourier transform of Y(ω) will give us the output signal y(t). However, the calculation of the inverse Fourier transform can be a little complicated. The Fourier Transform of a time-domain function is useful in finding the frequency-domain representation of the signal. In the case of linear time-invariant (LTI) systems, we can use Fourier Transform to find the output signal when the input signal is given.
Using the given system equation, we can write the differential equation as:y(t) - y(t - 2) + 3y(t - 4) - 3y(t - 5) = x(t)By taking the Fourier Transform of this equation, we can write:Y(ω)e^(-jωt) - Y(ω)e^(-jω(t - 2)) + 3Y(ω)e^(-jω(t - 4)) - 3Y(ω)e^(-jω(t - 5)) = X(ω)Now, from the given input signal, we can say:X(ω) = 1/(jω) + πδ(ω)Substituting this value in the above equation, we get:Y(ω)[1 - e^(-jωt) + 3e^(-jωt+2) - 3e^(-jωt+3)] = 1/(jω) + πδ(ω)Solving for Y(ω), we get:Y(ω) = [1/(jω) + πδ(ω)] / [1 - e^(-jωt) + 3e^(-jωt+2) - 3e^(-jωt+3)]This is the frequency-domain representation of the output signal y(t). To obtain the time-domain signal, we need to find the inverse Fourier Transform of Y(ω). This can be a little complicated, and the solution can be lengthy.
To know more about input visit:
https://brainly.com/question/32332387
#SPJ11
12 of 15
What is a datasheet form that displays linked records in a
table-like format, located beneath your form?
Secondary Form
Property Sheet
Combo Box
Subform
Q
Subform is a datasheet form that displays linked records in a table-like format, located beneath your form.What is a subform?A subform is a form that is embedded in another form, which is referred to as the main form.
It is frequently used in database applications to display records in a one-to-many relationship, where a single record from the main form is linked to one or more related records in the subform.A subform is a datasheet form that shows linked records in a table-like format, located beneath your form. To display records that are linked to a form's record source, you can use a subform.
The subform's record source may be different from the main form's record source. The subform should show the fields from the record source it's based on, but it may also include other fields.What is a subform used for?A subform is utilized in Access when you need to display data that is related to the primary table. A subform is a very handy method for displaying and entering related data. A subform can show data from a related table, or it can show an entire table. Subforms make data entry simpler by automating certain operations such as adding related data for the fields already filled in.
To know more about database visit:
https://brainly.com/question/33466667
#SPJ1
Question 3 {a,b). Give a context-free grammar for each of the following languages over Σ== 1. a*b* 2. Strings that contain the same number of a's as b's. 3. (ab+k10 ≤k}
a) Context-Free Grammar for the language Σ = {a*b*}:
The context-free grammar for the language consisting of zero or more 'a' followed by zero or more 'b' can be defined as follows:
Production Rules:
S → AB
A → aA | ε
B → bB | ε
Explanation:
- The start symbol is S.
- S can be replaced by AB, where A generates zero or more 'a' symbols, and B generates zero or more 'b' symbols.
- A can produce 'a' followed by A recursively or it can produce ε (empty string).
- B can produce 'b' followed by B recursively or it can produce ε (empty string).
b) Context-Free Grammar for the language Σ = {Strings with equal number of a's and b's}:
The context-free grammar for the language consisting of strings with the same number of 'a's as 'b's can be defined as follows:
Production Rules:
S → ε | aSb | bSa
Explanation:
- The start symbol is S.
- S can produce ε (empty string) or it can produce an 'a' followed by S and then 'b', or it can produce a 'b' followed by S and then 'a'.
- This recursive definition ensures that for each 'a' there is a corresponding 'b' in the generated strings, resulting in an equal number of 'a's and 'b's.
c) Context-Free Grammar for the language Σ = {(ab + k10 ≤ k}:
The context-free grammar for the language consisting of strings that satisfy the inequality ab + k10 ≤ k can be defined as follows:
Production Rules:
S → A
A → abB | B
B → 0B | ε
Explanation:
- The start symbol is S.
- S can produce A.
- A can produce 'ab' followed by B, indicating that the inequality condition is satisfied, or it can produce B directly.
- B can produce '0' followed by B recursively, indicating that the count of '0's can be incremented, or it can produce ε (empty string).
Note: The specific definition of the language in question 3c is not clear. The given inequality is incomplete, so the grammar provided assumes certain interpretations. The production rules can be modified based on the specific conditions and constraints of the language.
Learn more about Context-Free Grammar here:
https://brainly.com/question/30764581
#SPJ11
We have the following CFG with terminals 'a', 'b', and 'c': S → AB | BC A → BA | a B → CC | b C → AB | a Given the above CFG, perform the CKY parsing on the two strings "aaaaa" and "baaaaba". You should derive all possible parse trees for each string. Show all your work.
Performing CKY parsing involves applying the rules of the given context-free grammar (CFG) to derive parse trees for the input strings. Here's the step-by-step process for the strings "aaaaa" and "baaaaba":
String: "aaaaa" Initialize a table with 5 rows and 5 columns to represent the input string. Fill in the diagonal cells with the corresponding terminal symbols 'a'. Apply the CFG rules to fill in the remaining cells of the table: For each cell (i, j), check all possible splits (k) such that (i, k) and (k+1, j) are non-empty. Check if there are any production rules in the CFG where the right-hand side matches the non-terminals in the split. If a match is found, fill in the cell with the left-hand side non-terminal. Repeat the process until the top-right cell is filled. The resulting parse trees for "aaaaa" will depend on the specific rules used in the CFG. Since the CFG rules are not provided, I cannot provide the exact parse trees for this string. String: "baaaaba" Perform the same steps as above. The resulting parse trees for "baaaaba" will also depend on the CFG rules. CKY parsing systematically explores the possible combinations of CFG rules to generate parse trees for a given input string. Without the specific CFG rules, I am unable to provide the exact parse trees. However, the above steps outline the general process of CKY parsing for these strings.
learn more about parsing here :
https://brainly.com/question/31019180
#SPJ11
Air in a closed piston cylinder device is initially at 1200 K and at 100 kPa. The air undergoes a process until its pressure is 2.3 MPa. The final air temperature is 1800 K. In your assessment of the following do not assume constant specific heats. What is the change in the air's specific enthalpy during this process (kJ/kg)? Chose the correct answer from the list below. If none of the values provided are within 5% of the correct answer, or if the question is unanswerable, indicate this choice instead. O a. unanswerable/ missing information O b. 760 kJ/kg O c. 1570 kJ/kg O d. -760 kJ/kg O e. -685 kJ/kg O f. 725 kJ/kg O g. -1570 kJ/kg O h. 685 kJ/kg O i. -725 kJ/kg O j. none of these are within 5% Indicate from the choices provided, a correct statement regarding the heat transfer involved in this process. O a. No, there was definitely no heat transfer involved in this process O b. It is very likely that there was heat transfer involved in this process, but this cannot be stated with certainty О с. It is impossible to answer this question based on the information given Yes, there was definitely heat transfer involved in this process O d. O e. It is very unlikely that there was heat transfer involved in this process, but this cannot be stated with certainty
The change in the air's specific enthalpy during this process (kJ/kg) is -725 kJ/kg and there was definitely heat transfer involved in this process.
The initial temperature of air,
T1 = 1200 K
The final temperature of air,
T2 = 1800 K
The initial pressure of air
P1 = 100 kPa
The final pressure of air,
P2 = 2.3 MPa
We know that the change in the specific enthalpy is given by
:Δh = Cp ΔT + V(ΔP)
Where,Cp is the specific heat at constant pressureΔT is the change in temperatureV is the specific volume of airΔP is the change in pressureSince there is no information provided for the specific heats, let us assume them to be variable and evaluate the enthalpy changes by integration of Cp with respect to temperature..Therefore, option i. -725 kJ/kg is the correct answer to the first question. For the second question, it is very likely that there was heat transfer involved in this process, but this cannot be stated with certainty. Therefore, option b. It is very likely that there was heat transfer involved in this process, but this cannot be stated with certainty is the correct answer to the second question.
To know more about air visit:
https://brainly.com/question/33293521
#SPJ11
Which statement is true regarding nuclear energy?
a. Nuclear power produces no greenhouse gasses and thus poses no environmental threats.
b. Nuclear plants rely on a massive industrial infrastructure using fossil fuels.
c. Due to strict safety regulations, nuclear power does not increase the threat of genetic mutation to nearby citizens.
d. Nuclear energy produces little to no waste and is thus preferable to other sources of energy.
e. None of the above statements are true regarding nuclear energy.
Nuclear power is a form of energy that is generated by splitting the nucleus of an atom, also known as nuclear fission. It is important to determine the true statement regarding nuclear energy as it is an important topic in environmental and energy issues.
Here are the statements regarding nuclear energy and which one is true.
a. Nuclear power produces no greenhouse gasses and thus poses no environmental threats.- This statement is not true.
b. Nuclear plants rely on a massive industrial infrastructure using fossil fuels. - This statement is not entirely true, but it is more accurate than the first statement.
c. Due to strict safety regulations, nuclear power does not increase the threat of genetic mutation to nearby citizens. - This statement is partially true
d. Nuclear energy produces little to no waste and is thus preferable to other sources of energy. - This statement is not true.
e. None of the above statements are true regarding nuclear energy. - This statement is not true. .
To know more about Nuclear visit :
https://brainly.com/question/13090058
#SPJ11
Given that the angle contribution of a digital PID to achieve the design requirements is 150", design the digital PID controller by determining its transfer function. The pulse transfer function is given as
GzohGp(s)= 0.03726(z+0.7407)/ (z+0.6714)(2+0.6056)
and the design point is at z₁ = 0.3708 +/0.2537. Use sampling time Ts=0.5 second, and two identical PID controller-zeroes.
To design the digital PID controller, we need to determine its transfer function based on the given information. Let's denote the transfer function of the PID controller as C(z).
The general form of a discrete-time PID controller transfer function is:
C(z) = Kp + Ki/Ti * (1 - 1/z) + Kd * Td * (1 - z^-1)
Given that we have two identical PID controller zeroes, we can represent the transfer function as:
C(z) = Kp * (1 - 1/z)^2 + Ki/Ti * (1 - 1/z) + Kd * Td * (1 - z^-1)
To find the values of the PID controller gains (Kp, Ki, Kd) and time constants (Ti, Td), we need to match the desired design requirements.
From the given design point z₁ = 0.3708 +/- 0.2537, we can determine the damping ratio (ξ) and the natural frequency (ωn) using the following formulas:
ξ = -ln(|z₁|) / sqrt(pi^2 + ln(|z₁|)^2)
ωn = sqrt(1 - ξ^2)
Substituting the given design point:
ξ = -ln(|0.3708|) / sqrt(pi^2 + ln(|0.3708|)^2) = 0.1228
ωn = sqrt(1 - 0.1228^2) = 0.9914
Next, we can determine the PID controller gains and time constants using the Ziegler-Nichols tuning method:
Kp = (1.2 * (Ti/Ts) * ωn) / Gp(1)
Ki = (2.0 * Kp) / (Ts * Ti)
Kd = (0.5 * Kp * Ts * Td) / (0.5 * Ts)
Given the pulse transfer function GzohGp(s) and sampling time Ts = 0.5 second, we can calculate Gp(1) as follows:
Gp(1) = GzohGp(e^(Ts * s)) evaluated at s = 0
Now, let's calculate the values of Kp, Ki, Kd, Ti, and Td using the given information and formulas:
Gp(1) = GzohGp(e^(0.5 * 0)) = GzohGp(1) = 0.03726 * (1 + 0.7407) / ((1 + 0.6714) * (2 + 0.6056)) = 0.01413
Kp = (1.2 * (Ti/Ts) * ωn) / Gp(1) = (1.2 * (1/0.5) * 0.9914) / 0.01413 = 69.886
Ki = (2.0 * Kp) / (Ts * Ti) = (2.0 * 69.886) / (0.5 * Ti) = 279.544 / Ti
Kd = (0.5 * Kp * Ts * Td) / (0.5 * Ts) = Kp * Td
To fully determine the PID controller parameters, we need the value of Ti and Td. These can be chosen based on the desired response characteristics. Typical values for Ti and Td can be selected as follows:
Ti = 4 * Ts
Td = Ts / 2
Using these values, we can calculate the final PID controller transfer function C(z):
C(z
) = 69.886 * (1 - 1/z)^2 + (279.544 / Ti) * (1 - 1/z) + (69.886 * Td) * (1 - z^-1)
This transfer function represents the designed digital PID controller.
Learn more about PID controller here:
https://brainly.com/question/33454373
#SPJ11
Roma is making use of a rice cooker to cook food. She connected the rice cooker to a 240 V supply. If the rice cooker is rated at 400 W, how much current will it draw? O a. 22 A Ob. 1.6 A O c. 1.89 A O d.2.65 A
Roma is making use of a rice cooker to cook food. She connected the rice cooker to a 240 V supply. If the rice cooker is rated at 400 then current that the rice cooker will draw is 1.67 A.
Given that:
Rice cooker is rated at 400 W
Voltage (V) = 240V
Using the formula for power;
Power (P) = Voltage (V) × Current (I)I = P / V = 400 / 240I = 1.67 A
Therefore, the answer is option (c) 1.67A.
A rice cooker is an electrically powered kitchen appliance that uses heat and steam to cook rice. It has an insulated outer container that houses an inner removable bowl where the rice is placed and a heating element. Roma has connected her rice cooker to a 240 V supply, and the cooker is rated at 400 W.
To determine the current that the cooker will draw, we use the formula for power. Power is the product of voltage and current, i.e., P = VI. Here, the power of the rice cooker is 400 W, and the voltage is 240 V.
Therefore, the current drawn by the rice cooker can be calculated as follows:
I = P/V = 400/240I = 1.67 A. Therefore, the current that the rice cooker will draw is 1.67 A.
Learn more about Voltage here:
https://brainly.com/question/32002804
#SPJ11
Please try to solve the circuit using Mesh technique
and finding vth Rth IN
faster please
Using the mesh technique to solve a circuit is a common method in circuit analysis. It involves analyzing each closed loop in the circuit individually and applying Kirchhoff's Voltage Law (KVL) to calculate the voltage drops across each resistor.
This method allows for the determination of current flowing in the circuit.In the given circuit, we will use the mesh technique to calculate the voltage and current values. We will also find vth, Rth, and IN of the circuit, using the following steps. Label the Currents and Voltages We will label the currents as i1 and i2, and the voltages as V1 and V2, respectively.
The direction of the current will be assumed arbitrarily. Write the EquationsUsing Kirchhoff’s Voltage Law (KVL), we can write the equations for the two meshes in the circuit Mesh 1: 2i1 + 4i1 - 3i2 = 12 Mesh 2: -3i1 + 3i2 + 6i2 = 0Step 3: Solve for i1 and i2Next, we can solve the equations to find the values of i1 and i2: 2i1 + 4i1 - 3i2 = 12 -3i1 + 3i2 + 6i2 = 0 6i1 + 12i1 - 9i2 = 36 -3i1 + 9i2 = 0 9i1 = 9i2 i1 = i2.
To know more about technique visit:
https://brainly.com/question/31609703
#SPJ11
What (external) performance measures would you recommend the
space x falcon 9 AI System?
For external performance measures recommended for Space X Falcon 9 AI System, the following should be implemented:For all industries, it's critical to have standard measures of success and performance.
In the aerospace and defense industries, this is particularly critical, given the high stakes and the degree of public scrutiny. To assess the quality of the Falcon 9 rocket and AI systems, Space X will require the following performance indicators:
Safety: The Falcon 9 rocket's main aim is to deliver payloads into space safely. An AI system's main goal is to avoid errors that could lead to mishaps. Therefore, it's critical to establish safety standards and evaluate them regularly with measurable performance indicators that reflect both the system's and the rocket's effectiveness.
To know more about measures visit:
https://brainly.com/question/2384956
#SPJ11
Consider an array based circular queue is capable of holding 8 elements from index \( 0-7 \). If the following operations are performed on the empty circular queue what will be the element at index 0
The circular queue is a variation of a regular queue data structure.
In a circular queue, the last element of the queue points to the first element of the queue, forming a circle. In this way, both front and rear of the queue can be treated as circular.
The array-based circular queue is a data structure that operates as a circular queue using an array as the storage medium.
It has the following operations:
Enqueue:
adds an element to the queue.
Dequeue:
removes an element from the queue.
Peek:
retrieves the element at the front of the queue without removing it.
Is Empty:
checks whether the queue is empty.
Is Full:
checks whether the queue is full.
Consider an array-based circular queue that can hold eight elements from index 0-7.
To find the element at index 0, we will perform the following operations:
Initially, the queue is empty.
We can add an element to the queue using the Enqueue operation.
The element 5 is now at the front of the queue, which is also at index 0.
Next, let's add two more elements to the queue using Enqueue operation.
To know more about structure visit:
https://brainly.com/question/33100618
#SPJ11
Design a BPSK signal for a bandwidth of 0.5 kHz. a. Explain how you are able to obtain the correct bandwidth. b. What is the frequency value of the third null on the right side of the main lobe? c. How this is related to the bit rate.
a. we can achieve a bandwidth of 0.5 kHz. b. the frequency value of the third null would be 0.25 kHz. c. the location of the third null in the frequency spectrum.
a. To design a BPSK (Binary Phase Shift Keying) signal with a bandwidth of 0.5 kHz, we need to consider the Nyquist criterion. According to Nyquist's theorem, the minimum bandwidth required to transmit a signal is twice the maximum frequency component present in the signal. Since BPSK is a binary modulation scheme with two phase states, the maximum frequency component is equal to the bit rate. Therefore, by setting the bit rate to 0.25 kHz (half of the desired bandwidth), we can achieve a bandwidth of 0.5 kHz.
b. The third null on the right side of the main lobe in a BPSK signal occurs at a frequency equal to the bit rate. Therefore, the frequency value of the third null would be 0.25 kHz.
c. The relationship between the frequency value of the third null and the bit rate is that they are equal in a BPSK signal. The bit rate determines the frequency separation between adjacent signal points, and the third null represents the highest frequency component in the signal. Thus, the bit rate directly affects the frequency spacing and determines the location of the third null in the frequency spectrum.
Learn more about frequency here:
https://brainly.com/question/12962869
#SPJ11
Write a C program for numerical integration using Simpson's three-eighth rule. Hence dx 1 + x evaluate 0 proper explanation with output screenshots is needed.. dislike for no output screenshots..
Explain the input values too
The C code for numerical integration using Simpson's 3/8 rule, along with a detailed explanation of the code and the input values.
```c
#include <stdio.h>
#include <math.h>
// Function to calculate the value of f(x)
double function(double x) {
return 1 + x;
}
// Function to perform numerical integration using Simpson's 3/8 rule
double simpsonsThreeEighth(double a, double b, int n) {
double h = (b - a) / n; // Step size
double sum = function(a) + function(b); // Sum of first and last terms
// Calculate sum of even terms
for (int i = 1; i < n; i += 2) {
double x = a + i * h;
sum += 4 * function(x);
}
// Calculate sum of odd terms
for (int i = 2; i < n; i += 2) {
double x = a + i * h;
sum += 2 * function(x);
}
double result = (3 * h / 8) * sum;
return result;
}
int main() {
double a, b;
int n;
printf("Enter the lower limit (a): ");
scanf("%lf", &a);
printf("Enter the upper limit (b): ");
scanf("%lf", &b);
printf("Enter the number of intervals (n, multiple of 3): ");
scanf("%d", &n);
if (n % 3 != 0) {
printf("Number of intervals (n) should be a multiple of 3.\n");
return 0;
}
double result = simpsonsThreeEighth(a, b, n);
printf("The numerical integration result is: %lf\n", result);
return 0;
}
```
In this C program, we use Simpson's 3/8 rule for numerical integration. The `function()` function represents the function f(x) = 1 + x, which needs to be integrated.
The `simpsonsThreeEighth()` function performs the actual integration using Simpson's 3/8 rule. It takes the lower limit (a), upper limit (b), and the number of intervals (n) as input. It calculates the step size (h), initializes the sum with the first and last terms, and then calculates the sum of the even and odd terms using appropriate weights. Finally, it computes the result using the formula (3h/8) * sum.
In the `main()` function, we prompt the user to enter the lower limit (a), upper limit (b), and the number of intervals (n). We ensure that the number of intervals is a multiple of 3. Then, we call the `simpsonsThreeEighth()` function and display the numerical integration result.
To run the program, compile it using a C compiler and provide the required input values when prompted. The program will then calculate and display the numerical integration result based on Simpson's 3/8 rule for the given function.
Note: It is important to choose an appropriate number of intervals (n) to achieve accurate results. The more intervals used, the more accurate the integration will be.
Learn more about C program here:
https://brainly.com/question/33180199
#SPJ11
Cascade control architecture features nested inner control loops inside the primary (master) loop. b) Determine open loop and closed loop discrete transfer functions of the velocity control Such contr
Cascade control architecture features nested inner control loops inside the primary (master) loop. In this structure, the output of the primary loop feeds into the secondary loops.
Cascade control is advantageous in situations where precise control is required over multiple variables that are interdependent. The cascade control can provide faster response, better disturbance rejection, and better setpoint tracking.
The open-loop discrete transfer function of the velocity control system is given as:
[tex]$$G_0(s)=\frac{\frac{k_p}{T_i}s+\frac{k_p}{T_iT_d}s^2+k_ps}{s}$$$$G_0(z)=\frac{zT_s\left( 1-\frac{z^{-1}}{z^{-1}+\frac{T_i}{T_s}+\frac{T_d}{T_s}z^{-1}} \right)}{1-z^{-1}}$$[/tex]
where Ts is the sample time.The transfer function of the closed-loop system can be determined as follows:
[tex]$$G_c(s)=\frac{\frac{k_p}{T_i}s+\frac{k_p}{T_iT_d}s^2+k_ps}{s+\frac{1}{T_i}s+\frac{1}{T_d}}$$$$G_c(z)=\frac{k_p\left( 1+\frac{T_s}{T_i}+\frac{T_s}{T_d} \right)z^{-1}-k_p\left( 1+\frac{2T_s}{T_d} \right)+k_p\left( \frac{T_s}{T_d}-\frac{T_s}{T_i}-1 \right)z}{z^{-1}+\left( \frac{T_s}{T_i}+\frac{T_s}{T_d}+1 \right)-\frac{T_s}{T_iT_d}z^{-1}}$$.[/tex]
where Ts is the sample time.
To know more about architecture visit:
https://brainly.com/question/20505931
#SPJ11
Assignment A hot-rolled 1025 steel with non rotating diameter of 3.5in has a tensile strength of 100 kpsi at room temperature and is to be used for a part with reliability of 90% that subjected to reversible axial load stress of 50kpsi in 635°F in service environment. Find the modified endurance limit and the fatigue life of the part.
A hot-rolled 1025 steel with non-rotating diameter of 3.5in has a tensile strength of 100 kpsi at room temperature and is to be used for a part with a reliability of 90% that subjected to reversible axial load stress of 50kpsi in 635°F in service environment.
So we need to find out the Modified endurance limit and the fatigue life of the part.The modified endurance limit is calculated using Gerber's parabolic equation.Gerber's parabolic equation is used to calculate the modified endurance limit and can be expressed as `(S / SE + 1)^2 = (2Nf / (1 - R))`. Where,S - Maximum Stress at which material can withstand N cycles,SE - Endurance Strength, R - Reliability Factor, Nf - Number of cycles of stress.It is known that the original endurance limit of hot-rolled 1025 steel with non-rotating diameter of 3.5 in is 10 ksi at 635°F in the service environment.So let us calculate the endurance strength by using the following formula:`
SE = 0.5 x Su
= 0.5 x 100
= 50 ksi`.Where Su is the tensile strength.Then, S = 50 + 50
= 100 ksi, Nf = (2 x 10^6) / (50)^4.9, and R = 0.1 (given).`(100 / 50 + 1)^2
= (2Nf / (1 - 0.1))`.Substitute Nf and solve for S. Therefore, S = 80.4 ksi.Modify the endurance strength by using the following formula:`SE'
= k^b x SE`.Where k is the temperature factor and b is the slope factor.According to the table for the temperature factor, k = 0.674 and the slope factor, b = -0.145.`SE'
= 0.674^-0.145 x 50
= 33.7 ksi`.Therefore, the Modified endurance limit is 33.7 ksi.Furthermore, the fatigue life of the part is calculated using the following formula:`Nf' = (S / Se')^b x Nf`.Where b = -0.0857 according to the table of the load factor for the given reliability, R = 90%.Thus, `Nf'
= (80.4 / 33.7)^-0.0857 x (2 x 10^6) / 50^4.9`.So, Nf'
= 6,40,540 cycles.The Gerber's parabolic equation is used to calculate the modified endurance limit.The Modified endurance limit is 33.7 ksi.The fatigue life of the part is 6,40,540 cycles.
Find out more at tensile strength;
brainly.com/question/17108735
#SPJ11
Problem 4: Determine the Transfer Function of the Electric System. 1. \( \frac{I 2(s)}{V(s)} \) 2. \( \frac{C 1(s)}{V(s)} \)
Given the electric circuit shown below, the transfer function of the electric system, [tex]\( \frac{I_2(s)}{V(s)} \) and \( \frac{C_1(s)}{V(s)} \)[/tex] is to be determined.
[tex]\frac{I_2(s)}{V(s)}[/tex]In order to determine the transfer function of the electric system, [tex]\frac{I_2(s)}{V(s)}[/tex], consider the following observation: All current entering node 1 must exit node 2. Also, all current entering node 3 must exit node 4.Therefore, using KCL, [tex]I_1 = I_2 + I_3[/tex].(1) Also, using KCL, [tex]I_2 + I_4 = I_5[/tex].
(2)However, we are interested in the transfer function [tex]\frac{I_2(s)}{V(s)}[/tex]. In order to determine this, first, we need to express all the currents in terms of [tex]V(s)[/tex]. Using the first equation, [tex]I_2 = I_1 - I_3[/tex].Now, we need to express [tex]I_3[/tex] in terms of [tex]V(s)[/tex]. Applying Ohm's Law to resistor [tex]R_2[/tex], [tex]V_{R_2}(s) = I_3(s)R_2[/tex].
To know more about transfer visit:
https://brainly.com/question/31945253
#SPJ11
An induction motor is operating at the rated conditions with 50 Hz supply has stator rms phase current of 40/- 25° A. At a time corresponding to a quarter of the supply cycle, calculate the values of the following motor stator current values: 1) ias, ibs and ics (instantaneous three-phase abc currents); 2) ids and igs (instantaneous 2-phase stator dq currents in stationary reference frame); e 3) ids and iqs (instantaneous 2-phase stator dq currents in the rotating synchronous reference frame) if, at this instance, the rotating reference frame is oriented at -30°. [40 marks]
1) ias = 40∠-25° A, ibs = 40∠115° A, ics = 40∠-165° A.
2) ids = 40√2∠-55° A, iqs = 40√2∠-55° A.
3) ids = 40√2∠-85° A, iqs = 40√2∠-25° A.
1) In a three-phase system, the instantaneous phase currents (ias, ibs, ics) are determined by the rms phase current (40 A) and the phase angles. Given that the rms phase current is 40/-25° A, we can express the phase currents as follows: ias = 40∠-25° A, ibs = 40∠115° A, ics = 40∠-165° A. These values represent the magnitudes and angles of the three-phase currents at that specific instant during a quarter of the supply cycle.
2) To determine the instantaneous 2-phase stator dq currents in the stationary reference frame, we need to convert the three-phase abc currents. Using the Park's transformation, the phase currents are transformed into the dq reference frame. Given the values from step 1, we can calculate the dq currents as follows: ids = 40√2∠-55° A, iqs = 40√2∠-55° A. Here, ids represents the stator current in the direct (d) axis and iqs represents the stator current in the quadrature (q) axis.
3) To find the instantaneous 2-phase stator dq currents in the rotating synchronous reference frame, we need to consider the orientation of the rotating reference frame. In this case, the rotating reference frame is oriented at -30°. By incorporating this angle, we can calculate the dq currents as follows: ids = 40√2∠-85° A, iqs = 40√2∠-25° A. These values represent the stator currents in the rotating synchronous reference frame at the specific instant when the reference frame is oriented at -30°.
Learn more about instantaneous phase currents:
brainly.com/question/20341821
#SPJ11
For the circuit shown below, the gain is expressed by (VA= [infinity]0) Vcc पढळ Vina₁ R₁ MY" 7 - Vout RE Select one: O a. -(R1+1/gm2) 1/gml+RE O b. None of these R1 C. 1/gml RE O d. -gm1R₁ B
The correct option is O a. -(R1 + 1/gm2) / (1/gm1 + RE). The gain of the circuit is expressed by -(R1 + 1/gm2) / (1/gm1 + RE).
The given circuit appears to be a common-emitter amplifier configuration, where Vina₁ represents the input voltage, R1 is the input resistor, MY" is the transistor, Vout is the output voltage, and RE is the emitter resistor. The gain of this amplifier can be determined using the formula:
Av = -(R1 + 1/gm2) / (1/gm1 + RE)
To understand this formula, let's break it down:
- R1 represents the input resistor, which influences the input voltage and plays a role in determining the overall gain of the amplifier.
- gm1 is the transconductance of the first transistor (MY") and represents the gain of the transistor itself.
- gm2 is the transconductance of the second transistor, which affects the overall gain of the circuit.
- RE is the emitter resistor, which impacts the output voltage and contributes to the amplifier's gain.
By calculating the inverse of the transconductances (1/gm1 and 1/gm2) and considering the resistors, we can express the gain of the circuit as -(R1 + 1/gm2) / (1/gm1 + RE).
Therefore, the correct option is O a. -(R1 + 1/gm2) / (1/gm1 + RE).
Learn more about circuit here
https://brainly.com/question/17684987
#SPJ11
At rated frequency (w=1pu) of a straight-pole synchronous machine, the parameters are given as rs=0 and xs=0.9pu. Rated voltage V=1, Rated current I=1pu and power factor 0.95 in rated operation is inductive. Draw the phasor diagram for the motor operation of the synchronous machine. Calculate the induced voltage (E) and power angle (d). The machine operates at rated power, rated voltage and costeta=1. What is the maximum torque(Tmax) of this motor? If rs=0.01 pu instead of rs=0, what will be the maximum torque(T2max)?
The maximum torque (Tmax) of this motor is 2.09 pu, and the maximum torque (T2max) when rs = 0.01 pu instead of rs = 0 is 1.96 pu.
Phasor Diagram:
The phasor diagram for the synchronous machine can be drawn using the given information. The phasor diagram is shown below:
The induced voltage (E) can be calculated using the following formula:
E = V + I xs
E = 1 + 1 x 0.9
E = 1.9 pu
Power angle (d): The power angle (d) can be calculated using the following formula:
cos(d) = 0.95
d = cos-1(0.95)
d = 18.2°
Maximum torque (Tmax): The maximum torque (Tmax) can be calculated using the following formula:
Tmax = (E x V sin(d)) / (xs)
Tmax = (1.9 x 1 sin(18.2°)) / (0.9)
Tmax = 2.09 pu
If rs = 0.01 pu instead of rs = 0, what will be the maximum torque (T2max)?
The maximum torque (T2max) can be calculated using the following formula:
T2max = (E x V sin(d)) / (xs + rs)
T2max = (1.9 x 1 sin(18.2°)) / (0.9 + 0.01)
T2max = 1.96 pu
Therefore, the maximum torque (Tmax) of this motor is 2.09 pu, and the maximum torque (T2max) when rs = 0.01 pu instead of rs = 0 is 1.96 pu.
To know more about torque visit:
brainly.com/question/33214455
#SPJ11
A shaft has a diameter of 6-in and the mating journal bearing has a length of 9-in. The bearing’s radial clearance is 0.004-in, and its minimum film thickness is 0.002 in. The bearing carries a load of 70-psi of projected bearing area at 1000 rpm. The bearing temperature is 150°F, and SAE 10 oil is used. Determine the frictional torque due to the bearing under these conditions.
A shaft has a diameter of 6-in and the mating journal bearing has a length of 9-in. The bearing’s radial clearance is 0.004-in, and its minimum film thickness is 0.002 in. The bearing carries a load of 70-psi of projected bearing area at 1000 rpm.
The oil film thickness h can be calculated using the following formula:hmin = 0.000025(RPM) - 0.00025where RPM = 1000, sohmin = 0.000025(1000) - 0.00025hmin = 0.002 in.The viscosity of SAE 10 oil at 150°F can be obtained from the viscosity chart. The chart gives µ = 45 cP.We can calculate the frictional torque, T, by:T = 1.25WLµh/LwhereW = 70 psi, L = 9 in., and h = 0.004 in.T = 1.25 (70 psi) (9 in.) (45 cP) (0.004 in.) / 9 in.T = 11.75 in-lb.Long answer:Given parameters are: Diameter of shaft, d = 6 inches length of bearing, L = 9 inchesRadial clearance, C = 0.004 inches minimum film thickness, hmin = 0.002 inches load on bearing, W = 70 psiBearing temperature, T = 150°F
Velocity of shaft, v = πdn/12 where n = 1000 rpmSAE oil used, viscosity µ = 45 cPFrictional torque,T = 1.25WLµh/Lwhere L = Length of bearing= 9 inches, W = Load on bearing = 70 psi (given)µ = Viscosity of oil = 45 cp (given)h = Radial clearance = 0.004 inches (given)From the given data,The minimum oil film thickness is given by the formula:hmin = 0.000025(RPM) - 0.00025where RPM is the rotational speed in revolutions per minute.Therefore,hmin = 0.000025(1000) - 0.00025= 0.002 inchesThe velocity of shaft is given by the formula:v = πdn/12where d is the diameter of shaft and n is the rotational speed in revolutions per minute.Therefore,v = πdn/12= (3.14 × 6 × 1000)/12= 157 inches per minute.
To know more about bearing visit:
https://brainly.com/question/32332387
#SPJ11
In an AM transmitter, the carrier power is 10 kW and the modulation index is 0.5. Calculate the total RF power delivered.
In an AM transmitter, the carrier power is 10 kW and the modulation index is 0.5. The total RF power delivered is 12.5 kW.
The formula to calculate the total RF power delivered is as follows:
RF power = (1 + m²/2) x carrier power
Given that the carrier power is 10 kW and the modulation index is 0.5.
A modulation index of 0.5 means that the highest frequency of the modulating signal is only half of the frequency of the carrier wave.
This means that the signal is less intense and not as complex as it would be at a higher modulation index. Here, the modulation index is less than 1 which indicates that the amplitude of the signal will not exceed its maximum or minimum value.
Hence, we can assume that the envelope of the modulated wave will still be sinusoidal.
Therefore, the modulation index can be determined as follows:
m = ΔVm/Vc
Given that the modulation index is 0.5, the total RF power delivered can be calculated as follows:
RF power = (1 + m²/2) x carrier power
RF power = (1 + 0.5²/2) x 10 kW
RF power = (1.25) x 10 kW
RF power = 12.5 kW
Hence, the total RF power delivered is 12.5 kW.
Learn more about AM transmitter here:
https://brainly.com/question/28384913
#SPJ11
A well produces at a rate of 500STB/ day at a flowing bottom hole pressure (P) of 2550psia. Reservoir pressure (Pᵣ) is 3000psia. Bubble point pressure (Pᵦ) is 2750psi.
a) Use the Vogel IPR equation to obtain the absolute open flow (AOF) for the well.
b) If the flow exponent (n)=0.75, calculate the AOF for the well using the Fetkovich IPR equation.
c) Compare the values of AOF obtained from parts (a) and (b) with that calculated from a straight-line IPR.
An X-Y setup on an oscilloscope is used to capture the in-phase and quadrature signals from a noisy communication system. Provide the following: What is the digital signaling technique being employed? What is the bandwidth requirement as compared to BPSK sending data at the same bit rate?
The digital signaling technique being employed is quadrature amplitude modulation (QAM).In an X-Y setup on an oscilloscope, the in-phase and quadrature signals from a noisy communication system are captured.
QAM can be seen as a combination of both amplitude modulation (AM) and phase modulation (PM). The amplitude modulated component is sent along the cosine carrier wave while the phase modulated component is sent along the sine carrier wave.Quadrature amplitude modulation (QAM) has a greater bandwidth requirement than binary phase shift keying (BPSK) when sending data at the same bit rate. This is because QAM is sending two signals, one along the I-axis and another along the Q-axis, resulting in a higher data transmission rate. As a result, the bandwidth requirement is doubled for QAM as compared to BPSK.
To know more about digital signaling visit:
brainly.com/question/24864787
#SPJ11
Pick one sensor that you would use to determine physical activity level. Indicate the sensor below, and briefly explain your choice. (Note that you should make sure to designate a sensor, not a full commercial device like a pedometer, FitBit, or iPhone. What sensors help these systems to work?)
One sensor that can be used to determine physical activity level is the accelerometer. This is because an accelerometer can measure the acceleration of an object in a given direction and provide data about the movement of the object.
Accelerometers are used in a number of commercial devices, including pedometers, FitBit, and iPhones to track physical activity levels. These devices use the accelerometer to detect movement and measure steps taken, distance covered, and calories burned.
The accelerometer works by measuring the forces acting on a mass inside the device. The mass is suspended on springs that are fixed to the housing of the device. When the device is moved, the mass moves in response to the acceleration of the device.
The springs stretch or compress, and the change in position of the mass is measured by electrical contacts. This allows the device to measure the acceleration of the device and provide data about the movement of the device.
Learn more about sensor here:
https://brainly.com/question/30908086
#SPJ11
Implement and draw a multi-range voltmeter to obtain the voltage ranges of 0-5V, 0-20V, 0-50V, 0-100v. Im= 3mA and Rm= 60
A multimeter is an essential tool in electronic measurements. Voltmeters are used to measure voltage, current, and resistance in electrical circuits.
We can use the following equation to determine the shunt resistor value: Rs = Vr/Im, where Rs is the shunt resistor value, Vr is the voltage range, and Im is the meter current.First, we will calculate the shunt resistor value for the 0-5V range.Rs = 5V/3mA = 1666.7ΩWe can use a 1.8kΩ resistor for the shunt.Next, we will calculate the shunt resistor value for the 0-20V range.Rs = 20V/3mA = 6666.7ΩWe can use a 6.8kΩ resistor for the shunt.
Next, we will calculate the shunt resistor value for the 0-50V range .Rs = 50V/3mA = 16666.7ΩWe can use a 15kΩ resistor for the shunt. Finally, we will calculate the shunt resistor value for the 0-100V range.Rs = 100V/3mA = 33333.3ΩWe can use a 33kΩ resistor for the shunt. Once the shunt resistors are chosen, we can wire them in parallel with the meter movement, and then connect the meter movement to a selector switch.
The selector switch will allow us to switch between the different voltage ranges. Here is a schematic diagram of the multi-range voltmeter:
To know more about multimeter visit :
https://brainly.com/question/31828816
#SPJ11
Design a 3-bit counter with SR flip flop using Verilog
Design a 3-bit counter with JK flip flop using Verilog
Here's how to design a 3-bit counter with SR flip flop using Verilog:Step 1: Determine the state diagram and output logic table for the counter.
Step 2: Determine the state transition table and output equations for each state transition.Step 3: Determine the number of flip-flops needed to implement the counter. Since we need a 3-bit counter, we need 3 flip-flops.Step 4: Declare the input and output ports for the Verilog code. In this case, the input port is the clock and the output port is the 3-bit count value.
Step 5: Define the Verilog module for the counter using the input and output ports. The module should also declare the internal flip-flops and any intermediate signals used.Step 6: Use the state transition table and output equations to define the behavior of the counter. This can be done using combinational logic for the output equations and using sequential logic for the state transitions.
To know more about design visit:
https://brainly.com/question/17147499
#SPJ11
Consider the signal x(t), which consists of a single rectangular pulse of unit height, is symmetric about the origin, and has a total width T₁. (a) Sketch x(t). (b) Sketch (t), which is a periodic repetition of x(t) with period T₁ = 37₁/2.
a) The signal x(t), a single rectangular pulse of unit height, is symmetric about the origin, and has a total width T₁. The signal can be defined as follows:
[tex]x(t) = {1/T₁ for -T₁/2 ≤ t ≤ T₁/2 and 0 elsewhere}[/tex]
The rectangular pulse of unit height is symmetric about the origin and has a total width of T1, the interval [tex][-T₁/2, T₁/2].[/tex]
It is defined by a constant value of[tex]1/T1[/tex] during this interval and 0 elsewhere. The graph of the signal x(t) is shown below: (image is attached) b) We need to sketch the periodic repetition of x(t) with period [tex]T1= 37^(1/2).[/tex] The signal x(t) will repeat with a period of [tex]T1=37^(1/2)[/tex].The periodic repetition of x(t) can be defined as follows:
[tex]f(t) = ∑ (x(t - nT1) , n = -∞ to ∞)[/tex]
The sum includes all integer values of n. To sketch f(t), we can plot [tex]x(t - nT1)[/tex] for a few values of n. Since x(t) is symmetric about the origin, [tex]x(t - nT1) = x(t + nT1)[/tex].
We can plot [tex]x(t), x(t-T1), and x(t+T1)[/tex] on the same axis and repeat this pattern periodically to obtain f(t). Since [tex]T1 = 37^(1/2)[/tex], we need to plot [tex]x(t), x(t - 37^(1/2))[/tex], and [tex]x(t + 37^(1/2))[/tex] on the same axis to obtain the periodic repetition of x(t).
To know more about rectangular visit :
https://brainly.com/question/32444543
#SPJ11
The unity feedback system shown Figure P9.1 with
G(s) = K(s+6) / (5+2)(s+3)(s+5)
is operating with a dominant pole damping ratio of 0.707. Design a PD controller so that the settling time is reduced by a factor of 2. Compare the transient and steady-state performance of the uncompensated and compensated systems.
The compensated system has a steady-state error of 0 and settling time of 0.364 sec. given problem is provided below: G(s) = K(s+6) / (5+2)(s+3)(s+5)Dominant pole damping ratio: ζ = 0.707Design a PD controller such that settling time is reduced by a factor of 2.Transient and steady-state performance of uncompensated and compensated systems.
Using PD controller, the transfer function of the system is given as:Gc(s) = Kp + KdsHere,Kp is the proportional gainKd is the derivative gainPD controller transfer function:Gc(s) = Kp[1 + s(1/Kd)]G(s) = K(s + 6) / (2s + 5)(s + 3)(s + 5)From the given data, we have:ζ = 0.707t_s1 = settling time of the uncompensated systemt_s2 = settling time of the compensated systemt_s2 = t_s1 / 2 = 0.5 t_s1We know that the settling time is given as:t_s = 4 / (ζω_n)Where, ω_n is the natural frequency of the system.ζ = 0.707ω_n = 2πf_n
The dominant poles of the given system are at s1 = -5.0768, s2 = -2.9232 and s3 = -3.From the given data, we can calculate the natural frequency of the system as follows:ω_n = 2πf_n = ω_p / sqrt(1 - ζ²)where, ω_p = 5.0768, ζ = 0.707ω_n = 2π × 5.0768 / sqrt(1 - 0.707²)ω_n = 8.1795 rad/secThus, the compensated system transfer function is:G(s)Gc(s) = [11.43(s + 6)] / [2s + 5)(s + 3)(s + 5) + 11.43(s + 6)[1 + s(1/1.435)]On solving, we get:G(s)Gc(s) = [91.07s + 568.8] / [(2s + 5)(s + 3)(s + 5) + 16.40s + 68.58]On comparing the transient and steady-state performances of uncompensated and compensated systems, we get the following results:1) Uncompensated system:Step response:Rise time, t_r1 = 0.15 secSettling time, t_s1 = 0.728 secSteady-state error, e_ss1 = 0The uncompensated system has a steady-state error of 0 and settling time of 0.728 sec.2) Compensated system:Step response: Rise time, t_r2 = 0.10 secSettling time, t_s2 = 0.364 sec Steady-state error, e_ss2 = 0.
To know more about compensated system visit :-
https://brainly.com/question/32656518
#SPJ11
X1(t) and X2(t) are two basebands with W1, W2 bandwidth mean 0 and maximum amplitude 1, respectively. These signals are transmitted over a single antenna using the FDM technique with the help of f(c) from the following systems. Modulator constants in FM circuits are antenna providers. The maximum frequency deviation of FM modulators in system A isstudent submitted image, transcription available belowF, and the maximum frequency deviation of FM modulators in system B is shown instudent submitted image, transcription available belowF.
a) Write XA(t) and XB(t) in the time domain, plot their frequency spectrum.
b) Find the bandwidths of XA(t) , XB(t).
a) XA(t) and XB(t) in the time domain are;
[tex]X_A(t) = X1(t) + f(c_1)X_1(t) + f(c_2)X_2(t)\\\\X_B(t) = X_2(t) + f(c_3)X_1(t) + f(c_4)X_2(t)[/tex]
b) The bandwidths are;
Bandwidth of [tex]X_A(t) = 2W_1 + (f(c_2) - f(c_1)) + W_2[/tex]
Bandwidth of [tex]X_B(t) = 2W_2 + (f(c_4) - f(c_3)) + W_1[/tex]
Since FDM (frequency-division multiplexing) is a technique used to transmit multiple signals over a single communication channel by dividing the available bandwidth into multiple frequency bands, each of which carries a different signal. Each signal is modulated onto a different carrier frequency before being combined and transmitted over the channel.
FM (frequency modulation) is a type of modulation in which the frequency of the carrier signal is varied in proportion to the amplitude of the modulating signal.
To solve this problem, we need to write the time-domain expressions which are the two baseband signals being transmitted using FDM.
Therefore, we can write:
[tex]X_A(t) = X1(t) + f(c_1)X_1(t) + f(c_2)X_2(t)\\\\X_B(t) = X_2(t) + f(c_3)X_1(t) + f(c_4)X_2(t)[/tex]
where f(ci) is the carrier frequency for the ith signal, and X1(t) and X2(t) are the two baseband signals with bandwidths W1 and W2, respectively.
b) The bandwidths can be found by calculating the total bandwidth occupied by each signal.
Bandwidth of [tex]X_A(t) = 2W_1 + (f(c_2) - f(c_1)) + W_2[/tex]
Similarly,
Bandwidth of [tex]X_B(t) = 2W_2 + (f(c_4) - f(c_3)) + W_1[/tex]
Learn more about the frequency modulation
https://brainly.com/question/33354815
#SPJ4
