Explanation:
1 meter ≈ 3.281 ft.
so,
1 m² = 1m×1m ≈ 3.281 × 3.281 = 10.764961 ft²
now we have 22.3 ft² of skin.
that would be then
22.3/10.764961 = 2.071535605 ≈ 2.1 m² or even more rounded ≈ 2 m²
Which of these items is least likely to cause an exhaust emission test failure as of a result of excessive nox emissions? a) poorflow through the egr system. b) spark plug hot range. c) defective fuel injector d) defective oxygen senor
The item that is least likely to cause an exhaust emission test failure as of a result of excessive nox emissions is; poorflow through the egr system.
What is an exhaust emission?Exhaust emissions simply means substances emitted into the atmosphere from the exhaust discharge nozzle of an aircraft or aircraft engine.
Now, when the test fails as a result of excessive nox emissions, we can say that high NOx emissions can occur when an engine's air-fuel mixture is too lean. Thus, we can conclude that the reason for exhaust emission test failure as of a result of excessive nox emissions is due to poorflow through the egr system.
Read more about emissions at; https://brainly.com/question/14154063
5. Tech A says that shock absorbers can be tested with a "bounce test." Tech says than
is industry standard to replace an individual faulty shock absorber. Who is correct?
d. Tech A
b. Tech 8
8. Both A and B
d. Neither Anor B
Answer:
I know A is correct but not so sure about B, like I don't know if B is correct or wrong
A 750-m section of river runs parallel to a channel 1,000 m away. an aquifer connecting the two has hydraulic conductivity equal to 7. 0 m/day and an average thickness of 10 m. the surface of the river is 5. 0 m higher than the surface of the channel. estimate the rate of seepage (qseepage) from the river to the channel
Given a 750 m section with distance of 1000m , The calculated rate of seepage from the river to the channel has been calculated to be 262.5 m³/day.
What is the rate of seepage?
This is the calculated rate that shows how water is infiltrated downward into the soil.
The formula is given as
[tex]Q = KA \frac{dh}{dl}[/tex]
A = Area = 750*10 = 7500m
dh = h₂-h₁
= 10 - 5 = 5m
dl = 1000m
[tex]Q = 7*7500*\frac{5}{1000}[/tex]
= 262.5m³
The rate of seepage from the calculation above is 262.5m³.
Read more on rate of seepage: https://brainly.com/question/21499824
Where's an inductor most likely to be found in a power-supply circuit?
How many design did it take to make the eiffel tower?
Answer:
search is up
Explanation:
hope this helps!
A farmer has 12 hectares of land on which he grows corn, wheat, and soybeans. It costs $4500 per hectare to grow corn, $6000 to grow wheat, and $5000 to grow soybeans. Because of market demand the farmer will grow twice as many hectares of wheat as corn. He has allocated $6,375,000.00 for the cost of growing his crops. How many hectares of each crop should he plant?
The number of hectares of each crop he should plant are; 250 hectares of Corn, 500 hectares of Wheat and 450 hectares of soybeans
How to solve algebra word problem?
He grows corn, wheat and soya beans on the farm of 1200 hectares. Thus;
C + W + S = 12 ----(1)
It costs $45 per hectare to grow corn, $60 to grow wheat, and $50 to grow soybeans. Thus;
45C + 60W + 50S = 63750 -----(2)
He will grow twice as many hectares of wheat as corn. Thus;
W = 2C ------(3)
Put 2C for W in eq 1 and eq 2 to get;
C + 2C + S = 1200
3C + S = 1200 -----(4)
45C + 60(2C) + 50S = 63750
45C + 120C + 50S = 63750
165C + 50S = 63750 ------(5)
Solving eq 4 and 5 simultaneosly gives;
C = 250 and W = 500
Thus; S = 1200 - 3(250)
S = 450
Read more about algebra word problems at; https://brainly.com/question/13818690
Design an algorithm for computing √n
for any positive integer n. Besides
assignment and comparison, your algorithm may only use the four basic
arithmetical operations.
Please help me with this question
Answer:
4.2
Explanation:
The "allowance" is the difference between the maximum shaft size and the minimum hole size.
maximum shaft = C +D = 8.5 +0.1 = 8.6
minimum hole = A -B = 4.8 -0.4 = 4.4
Allowance = 8.6 -4.4 = 4.2
__
For an interference fit, the allowance is negative.
What does hydraulic force provide in a braking system?
Power
Heat dissipation
Contact surface
Pressure
Answer:
4 or D pressure
Explanation:
A hydraulic braking system transmits brake-pedal force to the wheel brakes through pressurized fluid, converting the fluid pressure into useful work of braking at the wheels.
Answer:
pressure is the correct answer...
Explanation:
mark me brainliest
A liquid jet vj of diameter dj strikes a fixed cone and deflects back as a conical sheet at the same velocity. find the cone angle θ for which the restraining force f = (3/2)rhoajvj^2 .
Answer:
lol i cant real it sorry
Explanation:
The PCV valve controls which emissions?
Answer:
The PCV reduces blowby emissions from the engine.
Which regulations are related to guard rail height and dimensions and uniformity of stairs?
a.
life safety
b.
fire safety
c.
structural safety
d.
health and welfare
Answer:
your answer should be C
Explanation:
bc I had the test
A capacitor is connected across an ac source. suppose the frequency of the source is doubled. what happens to the capacitive reactance of the capacitor?.
Answer:
Explanation:
The capacitive reactance of the capacitor is determined by [tex]X_{C}=\frac{1}{\omega C}[/tex]
When [tex]f'=2f \rightarrow \omega' =2\omega[/tex]
and [tex]X_{C}'=\frac{1}{2}X_{C}[/tex]
(The capacitive reactance will be reduced into 1/2 times of the previous capacitive reactance)
A gaseous mixture contain 32.9 mol % He, 40.7 mol % N_{2} and 26.4 mol % Ar. Determine the composition of this mixture on a mass basis based on the molecular weight given: MW(He) = 4.003 , MW (N_{2}) = 28.02 MW(Ar) = 39.95
The composition of the mixture on a mass basis are as follows:
He = 131.70 gN2 = 1140.41 gAr = 1054.68 gnumber of moles = mass of substnce / molar mass
molar mass and molecular weight has equal numerical values therefore
Number of moles = mass of substnce / molecular weight
mass of substance = number of moles * molecular weight
the moles are expressed in percentage hence the total moles should be 100
check: 32.9 + 40.7 + 26.4 = 100
He
mass of substance = 32.9 * 4.003 = 131.6987 g
[tex]N_{2}[/tex]
mass of substance = 40.7 * 28.02 = 1140.414 g
Ar
mass of substance = 26.4 * 39.95 = 1054.68 g
the engine needs a free flow of clean air to operate correctly and with low emissions. True or False
Answer:
true
Explanation:
How deep is a 6ft hole?
Answer:
I know this sounds quite deep but it is as deep as a grave
Explanation:
It's reality
Answer:
6ft or 72 inches
Explanation:
The hole is most likely 6ft or also known as 72 inches.
Hope this helps :-)
Have a great rest of your day or night!
<3 simplysun
Joe is a chemical engineer whose plant discharges heavy metals into the local river. By the test authorized by the city government, the amount of heavy metals is under the legal limit imposed by the city. By a new and more accurate test, the discharge is above the legal limit, that is, the discharge is in violation of environmental rules. Joe argues with his manager that the plant should reduce its discharges to comply with the newer and more accurate test.
The case contains a conceptual issue insofar as:
A.the issue is whether present emission rates constitute a violation of city regulations.
B.the issue is what is meant by “violation.”
C.the issue is how Joe should balance his obligations to his employer against his obligations to city residents.
D.the issue is whether the heavy metals presently emitted by the plant pose a threat to the health of the community.
Answer:
B probably
Explanation:
Because the prompt doesn't specify what sort of violation it could be anything maybe when they release the metals during the day and so on.
code lab write a floating point literal corresponding to the value of the first 6 digits of pi
Where do you look
for leaks coming from
the differential of a car?
Answer:
the side of the cover and draining along the bottom.Apr 1, 2021
Explanation:
i talking turtle with a key on its back told me
What do we mean by “whiteness” and how does that
determine/influence our society?
Answer:
whiteness refers to white people(WHITE americans), back then white people got all the good stuff while colored people (meaning everyone who is not white) got old breaking down things. This influenced our society back then and made people think that white people are way better than colored. Which is SO NOT true, everyone is the same
An amount P is deposited now so that an equal annual amount of A1=2000 per year for the first 5 years, starting 1year after the deposit. And a different annual withdrawal of A2= 3000 per year for the following 3 years. Draw the cash flow diagram if i=8.5% per year.
Based on the amounts to be withdrawn over the years and the interest rate, the amount deposited now is $12,977.
How much is deposited now?This can be found as:
= (2,000 x Present value of annuity interest factor, 8.5%, 5 years) + (3,000 x Present value of annuity interest factor, 8.5%, 8 years) - (P/A, 8.5%, 5 years)
= (2,000 x 3.9406) + (3,000 x (5.6392 - 3.94064))
= $12,977
The cashflow diagram is attached.
Find out more on cashflow diagrams at https://brainly.com/question/23841852.
marks)
Question 2
Distinguish between the following pairs of terms:
i. Quadrant bearing and Azimuth
5
ii. Constant error and Human error
5
iii. Referencing and Detailing
E
iv.
Accuracy and Precision
V. Bar scale and Representative fraction scale
Answer:
referencing and detailing
How Monopolies and Collusions Affect the Economy
Describe the concepts of monopoly and collusion in a market economy. Give five examples of monopolies and collusion among sellers and their effects on the market economy.
Answer:
Image result for How Monopolies and Collusion Affect the Economy Describe the concepts of monopoly and collusion in a market economy. Give five examples of monopolies and collusion among sellers and their effects on the market economy.
Collusion can lead to: High prices for consumers. This leads to a decline in consumer surplus and allocative inefficiency (Price pushed up above marginal cost) New firms can be discouraged from entering the market by types of collusion which act as a barrier to entry.
Explanation:
i hope this helped
A closed thermodynamic cycle consists of two isobaric and two isochoric processes. The processes operate between 0.43 MPa and 4.3 MPa and 0.28 m3 and 2.9 m3. Determine the total work (with appropriate sign) for one complete cycle, when the cycle operates in the clockwise direction. Provide your result in MJ.
Answer:
Explanation:
For first isobaric process (expansion with constant pressure):
[tex]W_{1}=P_{1}(V_{2}-V_{1})=(0.43\times 10^{6})(2.9-0.28)=1.1266 \times 10^{6} J=1.1266 MJ(+) (Expansion)[/tex]
Now, for the first isochoric: [tex]W_{2}=0[/tex], and [tex]Q_{2}=\Delta U=U_{3}-U_{2}[/tex]
For the second isobaric process (compression with constant pressure):
[tex]W_{3}=P_{2}(V_{1}-V_{2})=(4.3\times 10^{6})(0.28-2.9) =-11.266\times 10^{6}J=-11.266 MJ (Compression)[/tex]
For the last isochoric: [tex]W_{4}=0, Q_{4}=\Delta U=U_{4}-U_{3}[/tex]
So, the total work per cycle: [tex]W=W_{1}+W_{2}+W_{3}+W_{4}=1.1266+0-11.266+0=-10.1394 MJ[/tex]
Assume you have four fins, each with a mass of 8. 0 grams. What is the total weight of these four fins? (Hint: watch your units!) PLEASE HELP ASAP! I have a 0% in this class
Answer:
0.314 kg
Explanation:
[tex]\frac{8}{1000}[/tex] x 4 x 9.81
Answer:
.3139 joules
Explanation:
Weight in the metric system is ma
you have 4 fins that have MASS of 8 grams each
or 32 grams which is .032 kg
WEIGHT would be .032 kg * 9.81 m/s^2 = .31392 j
Briefly explain the four (4) main classification of rural latrine in Ghana and give example each.
Answer:
Temporally pit latrine ,improved latrine,ordinary latrine
Explanation:
l think the temporally latrine are used for camp ,vacation. improved latrine are at home for those who can afford. an ordinary latrine is used by people who can not afford money for removing fieces in the improved or temporally latrine
explain the S.A. co-ordinate system used in surveying
Answer:
A coordinate system is a method for identifying the location of a point on the earth. Most coordinate systems use two numbers, a coordinate, to identify the location of a point. Each of these numbers indicates the distance between the point and some fixed reference point, called the origin
Which of the following materials are examples of ceramics?
A
fiberglass, carbon fiber, and Kevlar
B
cedar, mahogany, and bamboo
C
brick, glass, and porcelain
D
nylon, leather, and asbestos
Answer:
c
Explanation:
A are types of fiberous materials
B is woods
c ceramics
D unrelated materials
How can the use of local materials improve the standard of living of Filipinos?
Find the magnitude of the two pulling forces P and Q when their resultant is 50 N at 20° with Q. P 20°
