The conclusion about the direction of motion of the object after the application of the additional force is the object will not move in either the left or right direction, because the net force will be zero.
What is force?In physics, a force is an influence that can change the motion of an object.
The object initially encountered unbalanced forces of 10 N from the right and 17 N from the left, resulting in a net force of 7 Netwons, which caused the object to travel in the direction of the right.
The object ceased to move in either direction when a force of 7 Newtons was added from the right, as the net force decreased to zero, creating balanced forces from both directions.
Therefore, the object will continue to move with a constant velocity.
To learn more about force, refer to the link:
https://brainly.com/question/1423274
#SPJ9
at what angle above the horizontal should the ball be thrown so that the runner will catch it just before it hits the ground? express your answer in degrees.
at the velocity of 60 degree angle above the horizontal should the ball be thrown so that the runner will catch it just before it hits the ground
For the person to be able to catch the ball, the horizontal component of velocity of the ball should be same as the speed of the person, i.e.,
v 0 cosθ= 2v 0
or cosθ= 21
or θ=60 ∘ .
Velocity is the directional speed of an object in motion as an indication of its rate of change in position as observed from a particular frame of reference and as measured by a particular standard of time.
Learn more about velocity, visit: brainly.com/question/17127206
#SPJ4
mass of 3 kg of a saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 160 kpa. initially, 1 kg of the water is in the liquid phase and the rest is in the vapor phase. heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 500 kpa. heat transfer continues until the total volume increases by 20%, while the pressure maintains at 500 kpa. determine (a) the initial and final temperatures, (b) the mass of liquid water when the piston first starts moving, and (c) the work done during this process. also, on your local computer, observe the process on a p-v diagram.
a) initial is 80.12°C and final temperature is 181.28°C b) Initial vapor mass is 2kg and liquid water is 0.7923 kg c) Heat transfer is 324.09 kJ
Law of thermodynamics:
ΔU = Q - W
Find initial state:
Specific volume of the mixture from the tables, which is [tex]0.9505 m^3/kg[/tex].
(a) Water has gone pressure condition (assumption). We can use the steam tables to find the specific volume of the water at the end of the process:
The specific volume of the water: [tex]0.9505 m^3/kg.[/tex]
Volume increases by 20%, so final: [tex]1.1406 m^3/kg[/tex].
Pressure: 500 kPa.
Saturation temperature: 500 kPa is 153.97°C.
Therefore, water is superheated region.
Specific volume water is: [tex]1.1406 m^3/kg.[/tex]
Temperature 181.28°C.
Initial temperature: 80.12°C
Final temperature: 181.28°C.
(b) Water is in pressure under piston.
The specific volume of water: [tex]0.9505 m^3/kg[/tex].
The pressure increases to 500 kPa: superheated vapor region:
Vapor specific volume: [tex]1.4074 m^3/kg[/tex].
Use ideal gas law:
V = m * v
V = [tex]2 kg * 1.4074 m^3/kg = 2.8148 m^3[/tex]
Since volume increases by 20%, initial volume is[tex]2.3457 m^3[/tex].
Use ideal gas law:
P * V = m * R * T
m = P * V / (R * T)
where R: gas constant
At 500 kPa and 181.28°C, the value of R * T is 298.48 kJ/kg.
Substituting:
m = [tex]500 kPa * 2.3457 m^3 / (0.4615 kJ/kg-K * 298.48 K) = 7.5768 kg[/tex]
Therefore, the mass of liquid water when the piston first starts moving is 3 - 7.5768 = -4.5768 kg.
It cannot be negative so therefore, some liquid water is present.
The specific enthalpy of the liquid water is 334.28 kJ/kg.
For saturated vapor = 2779.2 kJ/kg.
Initial enthalpy: 334.28 kJ.
Final pressure: 500 kPa
Final enthalpy:
[tex]H_final = H_initial + m_evap * (h_vap - h_liq)[/tex]
Substituting:
[tex]334.28 kJ + m_evap * (2779.2 kJ/kg - 334.28 kJ/kg) = H_finalH_final = 334.28 kJ + m_evap * 2444.92 kJ/kg[/tex]
Vapor specific volume: 1.4074 m^3/kg
Total volume:
[tex]V_final = V_initial + m_evap * v_vap[/tex]
Substituting:
[tex]2.3457 m^3 + m_evap * 1.4074 m^3/kg = V_final[/tex]
As 20% increase,
1.2 * V_initial = V_final
Substitute:
[tex]1.2 * 2.3457 m^3 = 2.8148 m^3 + m_evap * 1.4074 m^3/kgm_evap = (1.2 * 2.3457 m^3 - 2.8148 m^3)[/tex]
[tex]m_evap = (1.2 * 2.3457 m^3 - 2.8148 m^3) / 1.4074 m^3/kg = 0.2077 kg[/tex]
Mass of liquid when piston moves: 0.7923 kg.
c) To find work, use Thermodynamics 1st law:
Q = deltaU + W
Assume it is adiabatic process.
[tex]deltaU = m_evap * (u_vap - u_liq)[/tex]
The specific internal energy of the liquid water is 334.28 kJ/kg.
For saturated: 2594.2 kJ/kg.
Substitute:
deltaU = 0.2077 kg * (2594.2 kJ/kg - 334.28 kJ/kg) = 468.69 kJ
Work done is:
W = -P * deltaV
The specific volume of the liquid water is 0.0010441 m^3/kg.
The specific volume is 1.4074 m^3/kg.
Substitute:
deltaV = m_evap * (v_vap - v_liq)
Substituting:
deltaV = [tex]0.2077 kg * (1.4074 m^3/kg - 0.0010441 m^3/kg) = 0.2892 m^3[/tex]
Work done:
W = [tex]-500 kPa * 0.2892 m^3 = -144.6 kJ[/tex]
Heat transfer:
Q = [tex]deltaU + W = 468.69 kJ - 144.6 kJ = 324.09 kJ[/tex]
Learn more about heat transfer here:
https://brainly.com/question/13433948
#SPJ4
in a grocery store, you push a 15.5 kg shopping cart, such that it feels a horizontal net force of 14.0 n. if the cart starts at rest, how far does it move in 3.00 s?
The shopping cart moves a distance of 4.57 meters in 3.00 seconds.
Using Newton's second law, which relates force, mass, and acceleration we can solve this problem
F = ma
where F is the net force acting on the object, m is its mass, and a is its acceleration.
In the given problem, the net force acting on the shopping cart is 14.0 N, and its mass is 15.5 kg. We can rearrange the equation above to solve for the acceleration of the cart:
a = F/m
a = 14.0 N / 15.5 kg
a = 0.9032 [tex]m/s^2[/tex]
Now we can use the kinematic equation that relates distance, acceleration, and time:
d = 1/2 * a * [tex]t^2[/tex]
where d is the distance traveled, a is the acceleration, and t is the time.
Plugging in the values we have:
d = 1/2 * 0.9032 [tex]m/s^2[/tex] * [tex](3.00 s)^2[/tex]
d = 4.57 meters
Therefore, the shopping cart moves a distance of 4.57 meters in 3.00 seconds.
To learn more about Newton's second law:
https://brainly.com/question/25545050
#SPJ4
a sledge (including load) weighs 5000 n. it is pulled on level snow by a dog team exerting a horizontal force on it. the coefficient of kinetic friction between sledge and snow is 0.05. how much work is done by the dog team pulling the sledge 1000m at constant speed?
On light snow and hard snow, the coulomb friction coefficients were estimated to be 0.03 and 0.05, respectively. In this investigation, the intermediate and final phases of the coulomb friction coefficient were between 0.03 and 0.04. Thus, option B is correct.
What coefficient of kinetic friction for sledge and snow?The snow exerts kinetic frictional force on the sled's runners, slowing down and ultimately stopping the sled from moving. The coefficient of kinetic friction is 0.050.
Determine the value of the friction force.
[tex]F=uN = [0.05] [5000N] = 250N[/tex]
Here, N is the sledge's normal reaction force.
Write the expression for the work done.
[tex]F = f *d[/tex]
Here, d represents the horizontal distance.
[tex]W= (250)N (1000m) = 2.5 * 10^5 J[/tex]
Therefore, 2.5 * 10^5 The dog team pulls the sledge 1000 meters at a consistent speed to complete the task.
Learn more about kinetic friction here:
https://brainly.com/question/29100737
#SPJ4
The given question is incomplete. The complete question is given below:
A sledge (including load) weighs 5000 N. It is pulled on level snow by a dog team exerting a horizontal force on it. The coe�cient of kinetic friction between sledge and snow is 0.05. How much work is done by the dog team pulling the sledge 1000 m at constant speed?
A. 2.5×10^4J
B. 2.5×10^5J
C. 5.0×10^5J
D. 2.5×10^6J
E. 5.0×10^6J
Why does an iceberg have more total internal energy than a pan of boiling water, even though the iceberg has a lower temperature? In your answer, use the words “potential,” “kinetic,” and “thermal.”
An iceberg has more total internal energy than a pan of boiling water due to its greater potential energy and the greater amount of thermal energy contained in its larger mass.
What is total internal energy?
Total internal energy is the sum of the kinetic energy of the molecules in a system and the potential energy of their interactions. It is a measure of the energy contained within a system and is typically expressed in joules.
The total internal energy of an object is the sum of its potential and kinetic energies, as well as any thermal energy it contains. Even though the temperature of an iceberg is lower than that of a pan of boiling water, an iceberg has more total internal energy for two reasons: potential energy and the amount of thermal energy. Potential energy is energy that is stored in an object due to its position relative to other objects. An iceberg floating in water is at a higher position than the water in the pan, so it has more gravitational potential energy. Thermal energy is the energy that is associated with the random motion of particles in a system. The internal energy of a system is proportional to the temperature, but it also depends on the number of particles in the system, which is referred to as its mass. Since an iceberg is much larger than a pan of boiling water, it contains more particles and therefore has more thermal energy.
Therefore, greater potential energy and the greater amount of thermal energy contained in its larger mass.
To learn more about internal energy from the link
https://brainly.com/question/11623849
#SPJ1
what is the magnitude of the acceleration experienced by an electron in an electric field of 750n/c? how does the direction of the acceleration depends on the direction of the field at that point?
The magnitude of the acceleration experienced by an electron in an electric field of 750 N/C is approximately 1.318 × 10¹⁴ m/s².
If the electric field is in the direction of positive x-axis, the electron will be accelerated in the negative x-axis direction. If the electric field is in the direction of positive y-axis, the electron will be accelerated in the negative y-axis direction, and so on.
The magnitude of the acceleration experienced by an electron in an electric field can be calculated using the formula:
a = F/m
where F is the force experienced by the electron in the electric field, and m is the mass of the electron.
The force experienced by an electron in an electric field is given by:
F = qE
where q is the charge of the electron, and E is the electric field strength.
The mass of an electron is approximately 9.11 × 10⁻³¹ kg, and the charge of an electron is -1.602 × 10⁻¹⁹ C.
Substituting these values, we get:
F = (-1.602 × 10⁻¹⁹ C) × (750 N/C) = -1.2015 × 10⁻¹⁶ N
a = F/m = (-1.2015 × 10⁻¹⁶ N) / (9.11 × 10⁻³¹ kg) ≈ -1.318 × 10¹⁴ m/s²
Therefore, the magnitude of the acceleration experienced by an electron in an electric field of 750 N/C is approximately 1.318 × 10¹⁴m/s².
The direction of the acceleration of the electron depends on the direction of the electric field at that point. By convention, the direction of the electric field is the direction in which a positive charge would experience a force. Since the charge of an electron is negative, the force experienced by an electron in an electric field is opposite in direction to the electric field.
Learn more about electric field here :
brainly.com/question/15800304
#SPJ4
a clown 1.88 m tall looks at himself in a full-length mirror (floor-to-ceiling). at what point on the mirror must he look to see his feet (distance measured up from the floor)?
This is the same height as the clown, so if he looks up at the mirror from the floor he should be able to see his feet reflected in the mirror.
What is mirror?Mirror is a reflective surface, typically of glass, which displays images of objects placed in front of it. Mirrors are used in a variety of different applications, including personal grooming, decoration, interior design, viewing art, scientific uses, and more. A mirror is composed of a flat, smooth surface that reflects light in a specific direction. This reflection is what produces the image we see in the mirror. The reflective surface is usually made of glass, although other materials such as metal, plastic, and wood can also be used. Mirrors can be manufactured in a variety of shapes and sizes, from small hand-held makeup mirrors to large wall-mounted mirrors. Some mirrors are also designed with special coatings or treatments to enhance their reflective properties.
To know more about mirror
https://brainly.com/question/20380620
#SPJ1
for a person wearing these shoes, what??s the maximum angle (with respect to the horizontal) of a smooth rock that can be walked on without slipping?
The maximum angle (with respect to the horizontal) of a smooth rock that can be walked on without slipping is 50°.
Friction is a force that acts between two rough shells, whenever one tries to move one face against the other. When a force F pushes an object in one direction, there appears a disunion force in the contrary direction. Before stir thresholds, we're in the governance of static disunion.
Once the applied force is increased, the static disunion increases at the same rate, until it's reached a outside, denoted by maximum static disunion, and defined by the formula
[tex]f_s = \mu_s N[/tex]
The static measure between the shoe and the smooth gemstone is μs= 1.2
and hence the maximum static disunion is given by,
[tex]f_s = \mu_s N[/tex]
where N is the magnitude of the normal force. The forces acting on the shoe are
The gravitational force wielded by the Earth, of magnitude
F = mg
The normal force N wielded by the face of the gemstone, directed typically outwards from the gemstone.
The( static) disunion, wielded by the gemstone, in the direction overhead the gemstone( opposed to the tendency of slipping).
N - Fcosθ
N = Fcosθ
f = μFcosθ,
μFcosθ = Fsinθ
μ = sinθ/cosθ
Given by is the maximum (or critical) angle.
[tex]\theta_m_a_x = arctan\mu_s = arctan(1.2) = 50^0[/tex]
Learn more about Maximum angle:
https://brainly.com/question/17234359
#SPJ4
Complete question:
Shoes made for the sports of bouldering and rock climbing are designed to provide a great deal of friction between the foot and the surface of the ground. Such shoes on smooth rock have a coefficient of static friction of 1.2 and a coefficient of kinetic friction of 0.90. For a person wearing these shoes, what is the maximum angle (with respect to the horizontal) of a smooth rock that can be walked on without slipping?
What would happen if you tried using a road bike to ride across a soft surface. explain your answer?
a uniform beam with a mass of 120 kg and a length of 5.0 m rests on two supports, one at the left edge and one 3.0 m from the left edge. how close to the right edge can a 68-kg person walk along the beam without causing it to tip over?
If uniform beam with a mass of 120 kg and a length of 5.0 m rests on two supports, one at the left edge and one 3.0 m from the left edge then 1.6 m close to the right edge can a 68-kg person walk along the beam without causing it to tip over.
What is mass?
A body's mass is an innate characteristic. Prior to the discovery of the atom and particle physics, it was widely considered to be connected to the amount of matter in a physical body. It was found that different atoms and elementary particles had varying masses even if they theoretically contain the same quantity of stuff. In modern physics, there are a number of theoretically distinct but physically equal theories of mass. Experimentally, the mass of a body can be used to quantify its resistance to acceleration (change in velocity) in the presence of a net force.
To learn more about mass visit;
https://brainly.com/question/19694949
#SPJ4
the sun, with its diameter of 1.4 x 106 kilometers, is how many orders of magnitude larger than the earth, with its diameter of 1.3 x 104 kilometers. group of answer choices two orders of magnitude (i.e., a factor of 100 times bigger). four orders of magnitude (i.e., a factor of 10,000 times bigger). three orders of magnitude (i.e., a factor of 1,000 times bigger). one order of magnitude (i.e., a factor of 10 times bigger).
The sun is approximately two orders of magnitude (i.e., a factor of 100 times) larger than the Earth in terms of diameter.
To determine how many orders of magnitude larger the sun is than the Earth, we need to calculate the ratio of their diameters and take the logarithm (base 10) of that ratio.
The ratio of the sun's diameter to the Earth's diameter is:
1.4 x 10^6 km / 1.3 x 10^4 km = 107.7
Taking the logarithm (base 10) of this ratio gives:
log10(107.7) = 2.03
So the answer is that the sun is approximately two orders of magnitude (i.e., a factor of 100 times) larger than the Earth in terms of diameter.
For similar questions on sun's diameter to earth's diameter,
https://brainly.com/question/28700310
#SPJ4
Nichrome wire is used as heating element why?
Answer:
Explanation:
Nichrome wire is generally used as a heating element in heating appliances because it has the following features: It offers a very large resistance. So a large amount of electric energy is converted into a large amount of heat energy. It has a high melting point such that it can be heated till red hot without melting.
How do we define work as the product of force and distance in the direction of force?
Answer:
Work is defined as the product of force and distance in the direction of force because it represents the amount of energy that is transferred from one object to another as a result of a force being applied over a certain distance.
The definition of work as the product of force and distance (W = Fd) is based on the concept of energy transfer. Energy is defined as the ability to do work, and work is defined as the transfer of energy from one object to another. When a force is applied to an object over a certain distance, the energy that is transferred is equal to the amount of work done.
how many ( ) capacitors can be charged from a new - , - battery before the battery is likely exhausted of its stored energy? assume the charging operation has a 50% efficiency. (within three significant digits)
The capacitor is used to store charge.
What is a capacitor?We have to know that the capacitor is the kind of device that can be used to store the electrical charges. As such, the capacitor can be able to be charged from a battery.
This question is incomplete and the mathematical details of the problem are missing. However, we should know that the efficiency of the charging would depend on the kind of battery that has been used and the nature of the capacitor as we have in the question above here.
Learn more about capacitor:https://brainly.com/question/17176550
#SPJ1
what is the value of n for the electron following the emission?
The value of n for the electron emissions will be refer in each of the photoelectric effect, radioactivity. electron microscopy.
Photoelectric effect: In this process, electrons are emitted from a metal surface when light is shone on it. The energy of the incident light is absorbed by electrons in the metal, causing them to be ejected from the surface. "n" could refer to the energy level of the electron in the metal before it is ejected, which would determine the kinetic energy of the emitted electron.
Radioactive decay: Some radioactive isotopes undergo a process called beta decay, in which a neutron in the nucleus decays into a proton, emitting an electron in the process. "n" could refer to the energy level of the electron in the nucleus before it is emitted.
Electron microscopy: In electron microscopy, a beam of electrons is used to image a sample at high resolution. "n" could refer to the number of electrons emitted from the source, which would determine the intensity of the electron beam.
To know more about electrons here
https://brainly.com/question/860094
#SPJ4
the sun continues to shine today because of two kinds of balance. what are they and how do they work?
The two kinds of balance that keep the Sun shining are thermal equilibrium and hydrostatic equilibrium.
Thermal Equilibrium: The Sun shines by nuclear fusion, a process in which hydrogen atoms combine to form helium and release energy in the form of light and heat.
Hydrostatic Equilibrium: The Sun is also in hydrostatic equilibrium, which is the balance between the inward gravitational force and the outward pressure force.
These two balances are delicately intertwined and any disturbance to them could result in a catastrophic event such as a supernova or a collapse.
To know more about the sun, here
brainly.com/question/1116384
#SPJ4
determine which variables are known and which are not. an air-filled pipe is found to have successive harmonics at 480 hz , 800 hz , and 1120 hz . it is unknown whether harmonics below 480 hz and above 1120 hz exist in the pipe. what is the length of the pipe?
Below are the variables known and unknown of an air-filled pipe that have successive harmonica at 480hz, 800hz, 1120hzKnown. Successive harmonics at 480 Hz, 800 Hz, and 1120 Hz Unknown.
What are harmonics?Harmonics are overtones that are multiples of the fundamental frequency of a sound. They are produced when a sound wave is reflected from a surface, such as a wall or floor, and create a pleasant, ringing sound.
They are often used in music to create a fuller, richer sound. Harmonics can also be used to create a variety of effects in sound production, such as reverberation and echo.
For example, if a guitar is plucked, the note being played has a fundamental frequency but also has overtones which are produced by the guitar's body and strings.
To calculate the length of the pipe, it would be necessary to know the frequency of the first harmonic (the fundamental) and the frequency of the last harmonic. Without knowing this, it is not possible to calculate the length of the pipe.
Therefore, These overtones create a richer sound and are known as harmonics. The length of the pipe is unknown because the known harmonics do not provide enough information to calculate it.
Learn more about harmonics here:
https://brainly.com/question/9253932
#SPJ4
4) based on your data, compare the superposition principle for the electric fields and electric potential?
The electric field follows vector superposition while the voltage follows scalar superposition, which is the difference between the two superpositions (i.e., The net electric field at any point is the vector sum of the electric field due to the individual charges).
What is Electric field?
The term "electric field" refers to the physical field that surrounds electrically charged particles and acts to either attract or repel all other charged particles in the field (or E-field). One of the four fundamental interactions, or forces, of nature is the electromagnetic field, which manifests in both electric and magnetic fields. Electric fields, which are significant in many parts of physics, are used in electrical technology.
For instance, in atomic physics and chemistry, the electric field serves as the attractive force that holds the atomic nucleus and electrons of an atom together.
Moreover, it is the force that causes molecules to form when atoms bind chemically.
To learn more about Electric field visit;
https://brainly.com/question/15800304
#SPJ4
The soil sample was contaminated with equal amounts of caesium-137 and
iodine-131
Explain how the risk linked to each isotope has changed between 1986 and 2018
Both isotopes emit the same type of radiation.
Both caesium-137 and iodine-131 emit ionizing radiation, which can damage living tissue and increase the risk of cancer.
What are isotopes?Isotopes are members of the same element's family but have variable numbers of neutrons despite having the same number of protons.
Iodine-131 and caesium-137 both produce ionizing radiation, which can harm living things and raise the risk of cancer.
Due to their varied half-lives and processes of decay, each isotope's danger has changed between 1986 and 2018 despite this.
Caesium-137 degrades gradually over time since it has a longer half-life of roughly 30 years. Iodine-131, on the other hand, degrades swiftly because of its significantly lower half-life of only around 8 days.
Thus, the risk has diminished over time as a result of radioactive decay.
For more details regarding isotopes, visit:
https://brainly.com/question/11680817
#SPJ9
a thermometer is taken from a room where the temperature is 72o f to the outside where the temperature is 32o f. after 2 minutes, the thermometer reads 48o f. how many minutes does the thermometer have to be outside for it to read 36o f?
A thermometer is taken from a room where the temperature is 72° F to the outside where the temperature is 32° F. 1.26 minutes does the thermometer have to be outside for it to read 36° F.
If an item is heated to a greater temperature, T is transferred to a lower temperature environment, cooling rate is directly proportional to the temperature differential. By separating the variables, rewrite the equation. In the derived equation, substitute 0 for t and 72 for T.
If an item is heated to a greater temperature,
T is transferred to a lower temperature environment, T then the cooling rate.
By Newton's Law of Cooling
[tex]T(t) = T_{s} + Ce^{tr}[/tex]
Here, the ambient temperature, [tex]T_{s} = 32^{\circ} F[/tex]
The temperature to the outdoor, T(0) = 72°F
Use the equation [tex]T(t) = T_{s} + Ce^{tr}[/tex] to obtain that,
[tex]T(0) = T_{s} + Ce^{k - 0}[/tex]
72 = 32 + C
C = 40
So, [tex]T(t) = 32 + 40 e^{kt}[/tex]
After half minute, the temperature reads 48°F,
so, T(1/2) = 48
Then,
[tex]T(1/2) = 32 + 40e^{k \times \frac{1}{2}}[/tex]
[tex]48 = 32 + 40e^{\frac{k}{2}}[/tex]
[tex]40e^{\frac{k}{2}} = 16[/tex]
[tex]e^{\frac{k}{2}} = \frac{16}{40}[/tex]
[tex]e^{\frac{k}{2} = \frac{2}{5}[/tex]
[tex]\frac{k}{2} = \ln \left(\frac{2}{5} \right )[/tex]
k = 2 ln (2/5)
Therefore,
[tex]T(t) = 32 + 40e^{2 \ln \left(\frac{2}{5} \right) t}[/tex]
[tex]T (t) = 32 + 40 \left[ e^{\ln (\frac{2}{5} ) \right ]^{2t}[/tex]
[tex]T (t) = 32 + 40 \left(\frac{2}{5} \right)^{2t}[/tex]
Now find the time t when T(t) = 36
[tex]32 + 40 (\frac{2}{5})^{2t} = 36[/tex]
[tex]40 (\frac{2}{5})^{2t} = 4[/tex]
[tex](\frac{2}{5})^{2t} = \frac{4}{40}[/tex]
[tex]2t\ \ln (\frac{2}{5}) = \ln (\frac{1}{10})[/tex]
[tex]t = \frac{\ln (\frac{1}{10})}{2 \ln (\frac{2}{5})}[/tex]
[tex]t = \frac{-2.30}{2 \times (-0.91)}[/tex]
t = -2.30/-1.82
t = 1.26 min
Learn more about cooling rate from here;
https://brainly.com/question/14294022
#SPJ4
what is the surface charge density on the inner surface of the conducting shell?express your answer in terms of some or all of the variables q , a , b , and appropriate constants.
The surface charge density on the inner surface of the conducting shell can be expressed as: σ = q / (4πb^2), or σ = εq / (4πb^2).
To find the surface charge density on the inner surface of the conducting shell, we can use the formula:
σ = Q / A
where σ is the surface charge density, Q is the charge enclosed by the surface, and A is the area of the surface.
In this case, the charge enclosed by the surface is the charge q, since the conducting shell is neutral and does not contribute to the charge. The area of the inner surface of the shell is 4πb^2. Therefore, we have:
σ = q / (4πb^2)
Alternatively, we can use the fact that the electric field just outside the inner surface of the shell is E = q / (4πεb^2), where ε is the permittivity of free space. The electric field just inside the inner surface of the shell is zero, since the electric field inside a conductor is zero. Therefore, the charge density on the inner surface of the shell is given by:
σ = εE = εq / (4πb^2)
Read more about Charge Density:
https://brainly.com/question/14701915
#SPJ4
a 0.20 kg mass on a horizontal spring is pulled back 2.0 cm and released. if, instead, a 0.40 kg mass were used in this same experiment, the total energy of the system would
By the help of potential energy of the spring, so option A) 0.21 m/s is the correct answer.
There is no energy in the spring in its normal state, which is when it is not stretched. However, the spring can store energy when it is in a position that is different from its normal position because of the position. Potential energy is the name for this accumulated energy. The accumulated potential energy as a result of a specific elastic item, such as a spring, deforming is known as the potential energy of the spring. It reflects the labor involved in stretching the spring and is dependent on both the length of the stretch and the spring constant, k.
the energy of the spring = [tex]\frac{1}{2} kx^2[/tex]
so it depends on spring's constant
and change in length
so it is independent of mass
so, A) remains the same is the correct answer
B) total energy =[tex]0.5mv^2= 0.5\times0.2\times0.3^2[/tex]
total energy = [tex]9\times10^-3 J[/tex]
v = 0.21 m/s
so 0.21 m/s is the correct answer
Learn more about potential energy
brainly.com/question/29510087
#SPJ4
A force F is exerted on a 2.0 kg block to move it across a rough surface. The magnitude of the force is initially 5 N, and the block moves at constant velocity. While the block is movingthe force is instantaneous increases to 12 N. How much kinetic energy does the block now gain at it moves a distance of 2 m?
The block gains 4.49 J of kinetic energy as it moves a distance of 2 m
What is kinetic energy of the block?The increase in kinetic energy of an object can be calculated using the equation:
ΔKE = 1/2 (m)(Δv^2)
where;
m is the mass of the object, Δv is the change in velocity, and ΔKE is the change in kinetic energy.To find the change in velocity, we can use the equation of motion, which states that the net force on an object is equal to its mass times its acceleration:
F = ma
Rearranging this equation, we can find the acceleration:
a = F / m
The acceleration is the same before and after the force increases, so we can equate the two and solve for Δv:
F1 / m = F2 / m
F1 / m = (F1 + ΔF) / m
ΔF / m = F2 / m - F1 / m
ΔF / m = (12 N) / (2 kg) - (5 N) / (2 kg)
ΔF / m = 4.5 m/s^2
Δv = √(2 * ΔF / m)
Now that we have Δv, we can plug this value into the equation for ΔKE:
ΔKE = 1/2 * m * Δv^2
ΔKE = 1/2 * 2 kg * (2.12 m/s)^2
ΔKE = 4.49 J
Learn more about kinetic energy here: https://brainly.com/question/8101588
#SPJ1
According to the laws of thermodynamics, all energy transformations are inefficient because every reaction loses some energy to the surroundings as ________.
According to the laws of thermodynamics, all energy transformations are inefficient because every reaction loses some energy to the surroundings as heat
The second law of thermodynamics states that entropy in a system always has a tendency to rise. It claims that because some energy is constantly lost as heat with each energy transfer, no energy transfer mechanism is ideal. The system's entropy rises as a result of the energy wasted. Due to this, only 10% of the energy from one tropic level gets transferred to the next, with the remaining 90% being wasted as heat.
According to the second rule of thermodynamics, some energy is transferred as heat. Numerous biological processes include this ineffective energy transfer.
This indicates that part of the input energy gets transformed into a highly disordered form of energy when energy is transformed into a different form.
To know more about thermodynamics on
https://brainly.com/question/2305564
#SPJ4
PLEZS HELP I DON'T GET IT WILL MARK BRANILEST FOR THE BEST ANSWER :) Imagine that you were flying a small aircraft alone and had to
make an emergency landing in the forest below. Being the
amazing pilot that you are, you land safely, but your aircraft
is badly damaged and will not fly. It will be several days before
help can make it out to you, and you only have five items in
your emergency survival kit.
Would you rather land in a taiga or a temperate coniferous
forest? Why? What would you want in your survival kit and why?
What would you need from the forest to survive? What would the
dangers be?
Write your response in complete sentences.
the two factors that determine gravitational attraction are mass and what else?
Answer:
The distance between the two objects
The force is directly proportional to the product of the masses of the two objects and inversely proportional to the square of the distance between them
Explanation:
part (a) what is the magnitude of the z -component of the magnetic field, in units of teslas, at the origin of the coordinate system due to charge q1 ?
1. The z-component of the magnetic field due to charge one at the origin of the coordinate system, in teslas is (4π x [tex]10^{-7}[/tex] T m/A).
2. The z-component of the magnetic field due to charge two at the origin of the coordinate system, in teslas is 6.06 x [tex]10^{-5}[/tex] T.
3. The total magnetic field, in the z-direction, at the origin, due to the two charges, in teslas is 6.05 x [tex]10^{-5}[/tex] T.
1. To calculate the magnetic field at the origin of the coordinate system due to the two moving charges, we can use the Biot-Savart law, which relates the magnetic field at a point to the current or the moving charges producing it.
Let's first calculate the magnetic field at the origin due to charge one:
The magnitude of the magnetic field at a point due to a moving charge can be calculated using the equation:
B = (μ0/4π) x (q v sinθ / r²).
2. In this case, charge one has a charge of 0.15 C and is moving at a speed of 18.5 x [tex]10^6[/tex] m/s. The distance between charge one and the origin is 0.65 m.
B1 = (μ0/4π) x (0.15 x 18.5 x [tex]10^6[/tex] / 0.65²) = 6.06 x [tex]10^{-5}[/tex] T
The z-component of this magnetic field is zero since the field is perpendicular to the z-axis.
3. Next, let's calculate the magnetic field at the origin due to charge two:
B2 = (μ0/4π) x (5.50 x 2.5 x 10 / 0.65²) = -1.26 x [tex]10^{-7}[/tex] T
The negative sign indicates that the magnetic field due to charge two is directed along the negative z-axis.
Finally, let's calculate the total magnetic field at the origin due to both charges:
Since the magnetic fields due to the two charges are perpendicular to each other, we can simply add their magnitudes to obtain the total magnetic field in the z-direction:
Btot = B1 + B2 = 6.06 x [tex]10^{-5}[/tex] - 1.26 x [tex]10^{-7}[/tex] = 6.05 x [tex]10^{-5}[/tex] T
Learn more about the charges at
https://brainly.com/question/3412043
#SPJ4
The question is -
Consider the two charges, which are moving in opposite directions and located at a distance of 0.65 m on either side of the origin of the given coordinate system. Charge one is 0.15 C and is moving at a speed of 18.5 x 106 m/s, and charge two is 5.50 and is moving at a speed of 2.5 x 10 m/s.
What is the z-component of the magnetic field due to charge one at the origin of the coordinate system, in teslas?What is the z-component of the magnetic field due to charge two at the origin of the coordinate system, in teslas?What is the total magnetic field, in the z-direction, at the origin, due to the two charges, in teslas?Steady precipitation preceding a front is an indication of:a) stratiform clouds with moderate turbulence
b) cumuliform clouds with little or no turbulence
c) stratiform clouds with little or no turbulence
Steady precipitation preceding a front is most likely an indication of stratiform clouds with little or no turbulence.
The steady precipitation preceding a front is an indication of stratiform clouds with little or no turbulence. Stratiform clouds are layered and cover a large area, producing a wide, steady, and uniform precipitation that can last for many hours. These clouds form when moist air is lifted and cooled, resulting in a broad cloud layer with a relatively uniform base and top.
The steady precipitation ahead of a front is often caused by the uplift of warm air over cooler air, which creates a wide, relatively stable front. This stable front tends to produce stratiform clouds that extend over a large area and produce steady precipitation. On the other hand, cumuliform clouds are characterized by vertical development, producing showers and thunderstorms with a lot of turbulence.
Learn more about precipitation here:
https://brainly.com/question/18109776
#SPJ4
Select the gas with the highest average kinetic energy per mole at 298 K.
a. carbon dioxide
b. all have the same kinetic energy
c. hydrogen
d. water
e. oxygen
Hydrogen (H2) has the highest average kinetic energy per mole at 298 K. So, the correct option is (c) hydrogen.
What is average kinetic energy?The average energy of gas particles as a result of their mobility is measured by the gas's average kinetic energy. It is closely related to the gas's temperature, which is a gauge of the system's average particle kinetic energy. The following equation provides a gas's typical kinetic energy:
KEavg = kT (3/2)
where T is the absolute temperature of the gas in Kelvin, k is Boltzmann's constant, and KEavg is the average kinetic energy of a gas.
According to question:
Since a gas's average kinetic energy is directly correlated with its temperature, the gas with the lowest molar mass will have the highest average kinetic energy per mole at any given temperature.
Our calculations based on the molar masses of the given gases at standard conditions (298 K, 1 atm) show that hydrogen (H2) has the lowest molar mass at 2.016 g/mol, followed by carbon dioxide (CO2), water (H2O), and oxygen (O2), which have molar masses of 44.01 g/mol, 18.02 g/mol, and 32.00 g/mol, respectively.
In light of this, at 298 K, hydrogen (H2) has the highest average kinetic energy per mole. Hydrogen is the proper response, which is (c).
To know more about average kinetic energy visit:
https://brainly.com/question/28702344
#SPJ4
As a boat travels at 43. 0 km/h across the surface of a still lake, the waves it creates in the water have a speed of 25. 3 km/h
The waves created by the boat have a speed of 25.3 km/h, a period of approximately 0.37 hours, and a frequency of approximately 0.027 h⁻¹
When a boat travels at a certain speed across the surface of a still lake, it creates a series of waves that spread outwards from the boat. The speed of these waves depends on the properties of the water, such as its depth and temperature.
In this case, the boat is traveling at a speed of 43.0 km/h across the surface of a still lake, and the waves it creates in the water have a speed of 25.3 km/h.
The speed of the waves created by the boat can be calculated using the formula:
v = sqrt(gλ/2π)
where v is the speed of the waves, g is the acceleration due to gravity (9.81 m/s^2), λ is the wavelength of the waves, and π is the mathematical constant pi (approximately equal to 3.14).
Assuming that the wavelength of the waves is proportional to the speed of the boat, we can use the following formula to relate the wavelength of the waves (λ) to the speed of the boat (vb) and the speed of the waves (v):
λ = (v + vb) T
where T is the period of the waves, which is the time it takes for one complete wavelength to pass a fixed point.
We can rearrange this formula to solve for the period:
T = λ / (v + vb)
Substituting the given values, we get:
T = λ / (v + vb) = (25.3 km/h) / (43.0 km/h + 25.3 km/h)
T ≈ 0.37 hours
Finally, we can use the period of the waves to calculate their frequency (f), which is the number of waves that pass a fixed point in one second:
f = 1 / T
f = 1 / 0.37 hours ≈ 0.027 h⁻¹
Therefore, the waves created by the boat have a speed of 25.3 km/h, a period of approximately 0.37 hours, and a frequency of approximately 0.027 h⁻¹.
Learn more about speed here :
brainly.com/question/28609029
#SPJ4
