To find the image distance formed by a concave mirror, we can use the mirror equation:
1/f = 1/di + 1/do
Where:
f is the focal length of the mirror,
di is the image distance,
and do is the object distance.
In this case, the object distance (do) is given as 12.0 cm, and the focal length (f) is given as 15.0 cm. We can rearrange the equation to solve for the image distance (di):
1/di = 1/f - 1/do
Substituting the given values:
1/di = 1/15 - 1/12
To simplify this expression, we need to find a common denominator:
1/di = (12 - 15)/(12 * 15)
1/di = -3/180
Now, we can invert both sides to find di:
di = 180/-3
di = -60 cm
Therefore, the image distance is -60 cm. The negative sign indicates that the image is formed on the same side as the object (in this case, it is a virtual image).
Answer:
60 cm
Explanation:
the U (obj. distance) = 12 as it is a concave mirror then u = -12cm
the f = -15cm
by mirror formula
1/v + 1/u = 1/f
by substituting values
1/v + (1/-12) = 1/-15
1/v = 1/-15 -(1/-12)
1/v = 1/-15 + 1/12
by taking L C M 60
1/v = -(4/60) + 5/60
1/v = 1/60
so V = 60 cm
______ takes place when rocks bend because of pressure.
Answer:
Ductile deformation
Explanation:
When rocks bend because of pressure, ductile deformation takes place. Ductile deformation is a type of deformation that occurs when a material is subjected to a force that is greater than its yield strength. The yield strength is the stress at which a material begins to deform plastically. In the case of rocks, ductile deformation can cause the rocks to bend, fold, or even flow.
Ductile deformation is most likely to occur in rocks under high confining pressures. Confining pressures are pressures that act in all directions on a rock. The weight of overlying rock or sediment generally drives them. When rocks are under high confining pressures, they are less likely to fracture and more likely to deform plastically.
The process that takes place when rocks bend because of pressure is called "deformation."
Deformation refers to the changes in the shape, size, or orientation of rocks in response to applied stress. When rocks experience compressive forces or pressure over time, they can undergo plastic deformation, causing them to bend or fold.
This process commonly occurs in areas of tectonic activity, such as convergent plate boundaries, where large-scale forces act on the Earth's crust.
The bending and folding of rocks due to pressure can result in the formation of mountain ranges, fold belts, and other geological structures.
To know more about the deformation refer here,
https://brainly.com/question/13491306#
#SPJ11
A capacitor 2F is initially charged to 20 V and is connected to
50 resistance at t = 0. Find voltage v(t) across the capacitor for
t > 0. What is the net energy dissipated in the
resistor?
For the given problem statement, the capacitor 2F is initially charged to 20 V and is connected to 50 resistance at t = 0. We are supposed to find voltage v(t) across the capacitor for t > 0. Initially, the capacitor is charged to 20V and connected to a resistor of 50 ohms at t=0.
The voltage and current in the circuit can be defined as follows:
V = Voltage across capacitor
i = Current in the circuit
R = Resistance of the resistor
C = Capacitance of the capacitor Using Ohm's Law, we can write:
i = V/R Thus,
i = 20V/50 ohm = 0.4A Also, the voltage across the capacitor,
Vc = V = 20V.
As we know that the voltage across the capacitor is directly proportional to the charge across the capacitor and that the capacitor current is proportional to the rate of change of the voltage across the capacitor, we can write:i = C * (dVc/dt)As the voltage is constant in the given scenario, the rate of change of voltage (dVc/dt) is zero.
To know more about charged visit:
https://brainly.com/question/32449686
#SPJ11
14.9 The method of coincidences of Fabry-Perot rings is used to compare two wavelengths, one of which is 5460.740 Å, and the other slightly shorter. If coincidences occur at plate separations of 0.652, 1.827, and 3.002 mm, find (a) the wavelength difference and (b) the wavelength of 2'
Given,The Fabry-Perot rings method is used to compare two wavelengths, one of which is 5460.740 Å, and the other slightly shorter. If coincidences occur at plate separations of 0.652, 1.827, and 3.002 mm. We need to find
(a) the wavelength difference and(b) the wavelength of 2'.a) To find the wavelength difference, we need to use the formula:
\Delta\lambda=\frac{\lambda^2}{2d}Where,λ is the wavelength,d is the distance between the mirrors at coincidence.The difference between the wavelength is given by;\Delta\lambda=\frac{\lambda_1^2}{2d}-\frac{\lambda_2^2}{2d}\Delta\lambda=\frac{1}{2d}(\lambda_1^2-\lambda_2^2)Substitute,λ1 = 5460.740 Åλ2 = slightly shorterd1 = 0.652 mmd2 = 1.827 mmd3 = 3.002 mmTherefore,\Delta\lambda=\frac{1}{2 \times 0.652mm}\Big(\big(5460.740 \:Å\big)^2-\big(\text{slightly shorter}\big)^2\Big)Now, we have to find the wavelength of 2'.b) The plate separation of 2' is, d_2-d_1=3.002mm-1.827mm=1.175mm The wavelength of light is given by,\lambda=\frac{2d\cos\theta}{m} Where,θ is the angle of incidence on the mirrors, and m is the order of the interference fringe.In the second observation, the number of fringes counted is 2.So, m=2 and d=1.175 mm.Substitute the values in the above equation, we get:
\lambda=\frac{2\times 1.175mm\cos 0}{2}\lambda=1.175mm Therefore,The wavelength difference is;\Delta\lambda=\frac{1}{2 \times 0.652mm}\Big(\big(5460.740 \:Å\big)^2-\big(\text{slightly shorter}\big)^2\Big) The wavelength of 2' is;\lambda=1.175mmAbout WavelengthWavelength is the distance of one wave and is represented by the Greek letter Lambda (λ). On transverse waves, length can be calculated as the distance from the peak of the wave to the crest of the next wave, or the trough of the wave to the trough of the next. Wavelength is affected by the distance between the slits, the distance to the nearest fringe and the distance to the screen.
Learn More About Wavelength at https://brainly.com/question/10728818
#SPJ11
How
much wind speed from your mouth does it take to inflate a balloon
(consider how it is hard at first to inflate the balloon but as the
balloon inflates, it gets easier)?
When you inflate a balloon, you are blowing air into it with your mouth. When you blow air, the speed of the air changes based on how much the balloon has inflated. It takes a wind speed of approximately 10 mph from your mouth to inflate a balloon.
Blowing up a balloon takes some effort initially, but as the balloon gets bigger, the effort decreases. When you start to blow into the balloon, the air that you exhale is at room temperature, which means it is denser than the air inside the balloon. This makes it harder to inflate the balloon. The speed of air coming from your mouth is relatively slow at first.When the air inside the balloon starts to increase, the density decreases, making it easier to inflate the balloon. This means the speed of air coming from your mouth increases. When the balloon is full, the air inside is at a higher pressure than the air outside.
To know more about speed visit:
https://brainly.com/question/13489919
#SPJ11
(10 points) A physicist predicts the height of an object t seconds after an expertis meters above the ground. will be given by S(t)- 16- 2 sin thete (a) The object's height at the start of the experiment will be. (b) The object's greatest height will be. . meters. seconds after (e) The first time the object reaches this greatest height will be. the experiment begins. (d) Will the object ever reach the ground during the experiment? Explain why/why not.
We cannot find the exact height at the start of the experiment. The object's greatest height will be (16 + 2 sinθ) meters. The first time the object reaches the greatest height is when it is thrown vertically upwards.
a) Given, S(t) = h = x + y
Where, x = 16 m and y = 2 sinθS(t) = x + y = 16 + 2 sinθa)
The object's height at the start of the experiment will be h = x + y = 16 + 2 sinθThe value of sinθ is not given. Hence, we cannot find the exact height at the start of the experiment.
b) The object's greatest height will be:
The object's greatest height will be when the object is at the highest point i.e. when
v = 0.S(t) = x + y
where S(t) is the displacement of the object at time t.
As the object is at the highest point, its displacement from the ground will be equal to the greatest height it reaches. Let's find when the object is at its highest point. At the highest point,
v = 0.0 = v - gt0 = v0 - gt (initial velocity,
v0 = v + gt)gt = v0v0 = gt
Maximum height is reached when the object is halfway through its trajectory.
Maximum height, H = S(t) at t = T/2 = x + y at t = T/2
T = time period of oscillation.
T = 2π/ω, where
ω = angular frequency
ω = 2π/T
Let's find the angular frequency
ω = 2π/T = 2π/4 = π/2H = x + y = 16 + 2 sinθ (maximum height)
Therefore, the object's greatest height will be (16 + 2 sinθ) meters.
e) The first time the object reaches this greatest height will be
H = x + y = 16 + 2 sinθH
= 16 + 2H - 16 = 2 sinθH/2
= sinθ (H is the maximum height of the object)θ
= sin⁻¹(H/2)
Substitute
H = 16 + 2 sinθ = sin⁻¹((16 + 2 sinθ)/2) sinθ = sin(sin⁻¹((16 + 2 sinθ)/2)) = (16 + 2 sinθ)/2sinθ = 8 + sinθsinθ/1 + sinθ = 8/2sinθ/1 + sinθ = 4sinθ = 4 (1 + sinθ)sinθ - 4 - 4 sinθ = 0sinθ (1 - 4) = 4sinθ = -4/3
(rejected as it is out of range) or sinθ = 0sinθ = 0 ⇒ θ = 0°
Therefore, the first time the object reaches the greatest height is when it is thrown vertically upwards.
d) The object will never reach the ground as it will oscillate between its initial height and its greatest height.
To learn more about angular frequency:
https://brainly.com/question/3654452
#SPJ11
What is the power potential from a river per unit cross-sectional area if the water velocity is 2 m/s? (p = 1000 kg/m³)
We have a 1 m² cross-section of a river, and the water is flowing at 2 m/s, then the power potential from the river is 2000 W.
The power potential from a river per unit cross-sectional area can be calculated using the following formula:
Power potential = (1/2)*density of water*velocity of water^3 * area
where:
density of water is the density of water, in kg/m³
velocity of water is the velocity of water, in m/s
cross-sectional area is the cross-sectional area of the river, in m²
In this case, we have:
density of water = 1000 kg/m³
velocity of water = 2 m/s
cross-sectional area = 1 m²
Substituting these values into the formula, we get:
Power potential = (1/2) * 1000 kg/m³ * 2 m/s^3 * 1 m² = 2000 W
Therefore, the power potential from a river per unit cross-sectional area is 2000 W.
To learn more about velocity: https://brainly.com/question/31495959
#SPJ11
Mars is farther away from the Sun than Earth. Therefore, less radiation from the Sun reaches Mars. Mars also has a lower albedo than Earth. Mars emits 130 Wm to space from the TOA. Mars also has an atmosphere, though it is a lot different than Earth's. Due to its atmosphere, Mars' surface temperature is 240 K (-33°C), and the surface emits 188 Wm.
a. Calculate Mars' effective radiating temperature at the TOA.
b. Calculate the greenhouse effect (the temperature difference) on Mars due to the presence of its atmosphere.
c. These values from a) and b) are ____________ [Pick one: smaller than, the same as, larger than] those for Earth.
d. What is the value of the greenhouse effect on Earth?
Its greenhouse effect is given by;P = σεA(T⁴)390 = 5.67 x 10⁻⁸ x 0.95 x 5.10 x 10¹⁴ x (288⁴)288⁴ = 390/(5.67 x 10⁻⁸ x 0.95 x 5.10 x 10¹⁴)Surface temperature = 255K (-18°C)Greenhouse effect = 288 K - 255 K = 33 K.
a. Calculation of Mars' effective radiating temperature at the TOAMars radiates 130 Wm² to space from the TOA. Hence, this value is equal to the amount of radiation that should be emitted by a blackbody at the same temperature as Mars. Therefore, using the Stefan-Boltzmann Law;P = σεA(T⁴);
where P = 130 Wm², σ = 5.67 x 10⁻⁸ Wm⁻²K⁻⁴,
A = the surface area of Mars, and ε = the emissivity of Mars.
The amount of radiation that reaches Mars' surface is 188 Wm². Using the Stefan-Boltzmann Law, the temperature of the surface can be calculated.
P = σεA(T⁴)188 = 5.67 x 10⁻⁸ x 0.85 x 4.55 x 10¹⁴ x (240⁴)240⁴ = 188/(5.67 x 10⁻⁸ x 0.85 x 4.55 x 10¹⁴)
e values:These values from a) and b) are smaller than those for Earth.D. Value of greenhouse effect on EarthThe average surface temperature on Earth is 288 K (15°C), and its surface emits 390 Wm². Therefore,
To know more about radiates visit:
https://brainly.com/question/31106159
#SPJ11
7. Measure (in cm ) the distance from the left edge to each of the spectral lines in the comparison spectrum in Figure 1. Record these distances in column A. Similarly, measure the position of the lines (in cm ) in the spectrum of Star A. Record these in column B. Calculate the difference between the corresponding lines in column C. To convert the shift from cm to Angstroms, multiply the values of column C by the scale you found in Question 6. Record these values in column D. Using Figure 1, record the original wavelengths for each line in column E. Complete the remainder of the table as indicated. Use the value of 3×105 km/s for the speed of light.
Line comp.line position (cm) star A (cm) (A-B) shift (in A) original a (in a) D/E F x speed of light
1
2
3
4
8. The speed you get should all be nearly the same. Calculate the average of your four (4) speeds. This is the speed of the star. Δλ/λo=v/c
To determine the speed of a star, you can measure the shift in the wavelengths of its spectral lines compared to a reference spectrum.
The shift in wavelength is proportional to the speed of the star, so you can calculate the speed by dividing the shift by the wavelength of the light.
The average of the four speeds will give you the most accurate estimate of the star's speed.
The Doppler effect is the change in frequency or wavelength of a wave due to the motion of the source or observer. When a star is moving towards us, the wavelengths of its spectral lines are shifted towards the blue end of the spectrum.
When a star is moving away from us, the wavelengths of its spectral lines are shifted towards the red end of the spectrum.
The amount of shift in wavelength is proportional to the speed of the star. So, if we can measure the shift in wavelength of a star's spectral lines, we can calculate the speed of the star.
To measure the shift in wavelength, we can compare the star's spectrum to a reference spectrum. The reference spectrum is a spectrum of a star that is not moving, so the wavelengths of the lines in the reference spectrum are not shifted.
Once we have the shift in wavelength, we can calculate the speed of the star by dividing the shift by the wavelength of the light. For example, if the shift in wavelength is 0.1 Å and the wavelength of the light is 5000 Å, then the speed of the star is 0.1/5000 = 0.0002 = 200 m/s.
The average of the four speeds will give you the most accurate estimate of the star's speed. This is because the four speeds will be slightly different due to measurement errors. By averaging the four speeds, we can reduce the impact of the measurement errors.
To learn more about spectrum click here: brainly.com/question/31086638
#SPJ11
Q30(7)
D Question 7 2 pts What is the difference between fluorescence and phosphorescence? Which one can persist after the stimulating light has been turned off? Edit View Insert Format Tools Table 12pt Para
the main difference between fluorescence and phosphorescence is the timing of light emission.
Fluorescence and phosphorescence are both types of photoluminescence, which involve the emission of light by a substance after it has absorbed photons. However, there are distinct differences between the two phenomena.
Fluorescence:
- Fluorescence is the rapid emission of light by a substance upon absorption of photons.
- The emission of light in fluorescence occurs almost immediately after the substance is exposed to the stimulating light.
- Fluorescence typically lasts for a very short duration, ranging from nanoseconds to a few microseconds.
- Once the stimulating light is turned off, fluorescence ceases immediately.
Phosphorescence:
- Phosphorescence is the delayed emission of light by a substance after it has absorbed photons.
- Unlike fluorescence, the emission of light in phosphorescence occurs after a delay, even after the stimulating light has been turned off.
- Phosphorescence can persist for a longer duration, ranging from milliseconds to hours or even longer.
- This delayed emission occurs due to the transition of electrons to lower energy states with a slower rate of relaxation.
In summary, the main difference between fluorescence and phosphorescence is the timing of light emission. Fluorescence is an immediate emission of light that ceases when the stimulating light is turned off, whereas phosphorescence involves a delayed emission of light that can persist even after the stimulating light has been turned off.
to know more about photons visit:
brainly.com/question/28747953
#SPJ11
The inertia of the motor’s rotor is Jm, and its load is a propeller with three blades. You model the propeller as a simple planar body consisting of a uniform-density solid disk of 436 Chapter 26 radius R and mass M, with each blade a uniform-density solid rectangle extending from the disk. Each blade has mass m, length , and (small) width w.
a. What is the inertia of the propeller? (Since a propeller must push air to be effective, ideally our model of the propeller inertia would include the added mass of the air being pushed, but we leave that out here)
b. What gear ratio G provides inertia matching?
a) The inertia of the propeller is calculated as 0.065031 kg m² ; b) The gear ratio G provides inertia matching is calculated as 0.196.
a. The inertia of the propeller: Let’s find the moment of inertia of the disk by using the equation:[tex]I = (1/2) M R²[/tex]
Given that M is the mass of the disk and R is the radius of the disk. By substituting the values, we get:
[tex]I = (1/2) M R²[/tex]
= (1/2) × 3.14 × 0.0256 × 1.6
= 0.065 kg m²
The moment of inertia of each blade about the Centre is given as: [tex]I = (1/12) m (l² + w²)[/tex]
By using the given values, we get: [tex]I = (1/12) m (l² + w²)[/tex]
= (1/12) × 0.035 × 0.16²
= 1.04 × 10⁻⁵ kg m²
Total inertia of the propeller can be found by summing up the moment of inertia of the disk and three blades.
I Total = I₁ + 3 × I₂
= 0.065 + 3 × 1.04 × 10⁻⁵
= 0.065031 kg m²
b. The gear ratio G provides inertia matching. The gear ratio G provides inertia matching can be found by using the following formula.G² = Jm / ITotalBy substituting the values, we get:
[tex]G² = Jm / ITotal[/tex]
= 0.0025 / 0.065031
= 0.0384G
= √0.0384
= 0.196
So, the gear ratio G provides inertia matching is 0.196.
To know more about inertia, refer
https://brainly.com/question/1140505
#SPJ11
: P.8-12 The magnetic field intensity of a linearly polarized uniform plane wave propagating in the + y-direction in seawater [e, = 80, ,= 1, o = 4 (S/m)] is H=a₂0.1 sin (10¹⁰nt - n/3) (A/m) at y = 0. a) Determine the attenuation constant, the phase constant, the intrinsic impedance, the phase velocity, the wavelength, and the skin depth. b) Find the location at which the amplitude of H is 0.01 (A/m). c) Write the expressions for E(y, t) and H(y, t) at y = 0.5 (m) as functions of t.
a) Attenuation constant, α:
The skin depth δ for seawater can be calculated using the following formula:
[tex]δ=√(2/ωμσ)[/tex] where ω is the angular frequency, μ is the magnetic permeability of the medium, and σ is the electrical conductivity of the medium. Now, substituting values, [tex]δ=√(2/(10^10*4*π*10^-7*80))[/tex]
= 3.18 m Phase constant,
[tex]β = 2π/λ[/tex], where λ is the wavelength. Hence,
[tex]β = (10^10*2π)/3[/tex]
[tex]= 20π x 10^9[/tex] Intrinsic impedance,
[tex]η = √(μ/ε) = 377 Ω[/tex] Phase velocity,
[tex]vp = ω/β[/tex]
[tex]= 10^10/20π[/tex]
[tex]= 1.59 x 10^8 m/s[/tex] Wavelength,
[tex]λ = vp/f[/tex]
= (1.59 x 10^8)/(10^10)
[tex]= 0.0159 m (or 1.59 cm)[/tex]b) Let's substitute the given value of H into the equation:
[tex]0.01 = a₂0.1 sin (10¹⁰nt - n/3)[/tex] Thus, sin ([tex]10¹⁰nt - n/3[/tex])
[tex]= 0.01/a₂0.1[/tex]
[tex]= 0.1/20a₂[/tex]
[tex]= 0.1/(20 sin (10¹⁰nt - n/3)).[/tex]
To know more about constant visit:
https://brainly.com/question/31730278
#SPJ11
In a horizontal pipe carrying water, the cross-sectional area gradually increases, thus: O The velocity increases and the static pressure increases O The velocity increases but the static pressure remains the same as the pipe is horizontal O The velocity increases and the static pressure decreases The static pressure increases and the dynamic pressure increases O The static pressure increases, and the dynamic pressure reduces To measure pressure on an inclined manometer to better than 1% accuracy: O When checking the zero level in manometers you must always read the bottom of the meniscus but when taking any other reading it does not matter O You must always read the top of the meniscus when checking the zero level and the bottom of the meniscus when taking any readings O When it is inclined at 90 degrees (i.e., vertically), we only need to know the angle of inclination to within #- 5 degrees O When it is inclined at 10 degrees to the horizontal, we need to know the angle within +/- 1.0 degree O This is incorrect - you cannot measure to 1% accuracy on a manometer At the entrance to a small wind tunnel, air is drawn from the atmosphere into the duct by a downstream fan. A static pressure tube is inserted into the duct and connected to one tube of a manometer - the other tube is open to atmosphere. What will happen to the fluid level (on the side of the total tube) when the fan is turned on? O Fluid will rise up the tube O Fluid will drop if there are no leaks O Fluid will go down due to energy losses O None of the listed statements is correct O Fluid will remain completely unchanged In a horizontal pipe carrying water, the cross-sectional area gradually expands and the flow does not separate, thus: O The dynamic pressure reduces and the static pressure increases O The dynamic pressure increases and the static pressure decreases O The static pressure increases and the dynamic pressure increases O The static pressure increases and the dynamic stays constant O The velocity decreases but the static pressure remains the same as the pipe is horizontal
In a horizontal pipe carrying water, the cross-sectional area gradually increases, thus the velocity increases and the static pressure decreases. The fluid mechanics also describe that the static pressure increases and the dynamic pressure reduces at the entrance to a small wind tunnel.
Static pressure and dynamic pressure are two essential types of pressure that are used in fluid mechanics. Static pressure refers to the force that a fluid exerts on an object. Dynamic pressure refers to the kinetic energy of a fluid that is in motion. A horizontal pipe that carries water and gradually increases its cross-sectional area experiences a decrease in static pressure and an increase in velocity.
When the air is drawn into the duct through a downstream fan, the fluid level of the manometer on the total side of the tube will rise. In contrast, if the fluid experiences energy losses, the fluid level will go down. Gradual expansion in the cross-sectional area of a horizontal pipe carrying water causes the velocity to increase, and the static pressure remains the same.
To know more about mechanics visit:
https://brainly.com/question/28990711
#SPJ11
[#665] Car physics, part 3 A car has a drag coefficient Ca = 0.30, a frontal area of A = 1.9 m², a mass 1.2 tonnes and a coefficient of rolling resistance, Cr, -0.012. It is travelling up a hill with a slope of 1 in 20 at 110 kph. At what rate is it doing work against gravity (i.e. at what rate is it increasing its gravitational potential energy)? Pg= kW. (A 1:20 grade means that it rises 1 m for every 20 m travelled along the road: sin(0) = 1/20.) Enter answer here
We need to calculate the rate at which the car is doing work against gravity, We can calculate the power required by the car to climb the hill using the following formula: P = F × v where F is the force required to move the car up the slope and v is the velocity of the car.
By resolving forces, we can find that the force required to move the car up the slope is:
F = mg sin θ + 0.5ρAv²Ca + mgCr
Plugging in the values, we get:
F = 1.2 × 9.81 × 1/20 + 0.5 × 1.225 × 1.9 × 30.56² × 0.30 + 1.2 × 9.81 × (-0.012)
= 4717.17 N
The power required to move the car up the slope is:
P = F × v
= 4717.17 × 30.56
= 144167.11 W
= 144.17 kW
The car is doing work against power at a rate of 144.17 kW.
To know more about coefficient visit:
https://brainly.com/question/31220381
#SPJ11
why does a node in a standing wave have zero displacement
Answer:
Destructive interference
Explanation:
At a node, there is complete destructive interference at all times, so the displacement is zero. Why does a node in a standing wave have zero displacement? As the siren moves away, each wave front produced by the siren is farther from the previous wave front than if the siren were standing still.
A node in a standing wave has zero displacement because it is the point where two waves traveling in opposite directions cancel each other out, resulting in destructive interference and no movement of particles from their equilibrium position.
In a standing wave, nodes are points that do not experience any displacement. This occurs due to the interference of two waves traveling in opposite directions. When two waves with the same amplitude and frequency pass through each other, they create a standing wave pattern.
The nodes are the points where the two waves cancel each other out, resulting in zero displacement. At these points, the crest of one wave coincides with the trough of the other wave, causing destructive interference. As a result, the particles at the nodes do not move from their equilibrium position and remain at zero displacement.
Learn more:
About node here:
https://brainly.com/question/30885569
#SPJ11
A 225-g sample of a substance is heated to 350 ∘C and then plunged into a 105−g aluminum calorimeter cup containing 175 g of water and a 17−g glass thermometer at 12.5 ∘C. The final temperature is 35.0 ∘C. The value of specific heat for aluminium is 900 J/kg⋅C ∘, for glass is 840 J/kg⋅C ∘, and for water is 4186 J/kg⋅C ∘.
In the given problem, the initial temperature of the sample is not given. So, the amount of heat transferred (q) can be calculated as,`
q = (mass of substance) × (specific heat of substance) × (change in temperature of substance)`
Heat gained by aluminum calorimeter, `q_1
= (mass of aluminum calorimeter) × (specific heat of aluminum) × (change in temperature of aluminum calorimeter)
`Heat gained by the thermometer, `q_2
= (mass of glass thermometer) × (specific heat of glass) × (change in temperature of glass thermometer)`
Heat gained by the water, `q_3 = (mass of water) × (specific heat of water) × (change in temperature of water)`
The heat transferred by the substance will be equal to the sum of the heats gained by the calorimeter, thermometer and the water i.e.`q = q_1 + q_2 + q_3`The specific heat capacity of the substance can be calculated using the formula for q.
The values of mass and temperature are given in the problem, so let's put the values in. q = 225 g × c × (35.0°C - T) Where T is the initial temperature of the substance. Now, the value of q can be calculated using the heat gained by the calorimeter, thermometer, and water. The final temperature of the mixture of water, calorimeter, and thermometer is 35°C; the initial temperature of the water and calorimeter is 12.5°C; the change in temperature is (35.0 - 12.5) °C = 22.5°C.
To know more about calorimeters, visit:
https://brainly.com/question/10678032
#SPJ11
How does the number of coils affect the energy efficiency of a transformer as in the difference between a transformer with 10 turns in the primary coil, 20 turns in secondary coil (ratio of 1:2) and a transformer with 20 turns in the primary coil, 40 turns in the secondary coil (also ratio of 1:2)?
The energy efficiency of a transformer is affected by the number of coils. The more the number of coils, the higher the energy efficiency.
The number of coils in a transformer has a significant impact on its performance and efficiency. The transformer's primary coil and the secondary coil must have a certain number of turns to achieve the desired performance. The ratio of the turns is also essential in this regard.
For instance, a transformer with a 10 turn primary coil and 20 turn secondary coil will have a 1:2 ratio. The transformer will operate at a lower frequency with fewer turns, which will cause the primary coil to consume less energy and produce less current. In contrast, a transformer with a 20 turn primary coil and a 40 turn secondary coil will also have a 1:2 ratio.
The transformer will have more turns, which will cause the primary coil to consume more energy and produce more current. However, it will operate at a higher frequency due to the increased number of turns in the secondary coil, which will reduce its efficiency.
The number of coils used in the construction of a transformer affects its energy efficiency and performance. It is critical to select the right number of coils and turns to achieve the desired performance and efficiency.
To learn more about transformer visit;
https://brainly.com/question/15200241
#SPJ11
Take Home Machines 2- An automotive alternator is rated 550 VA and 20 V. It delivers its rated voltamperes at a power factor of 0.90. The resistance per phase is 0.05 2, and the field takes 2 A at 12 V. If the friction and windage loss is 35 W and the core loss is 40 W, calculate the percent efficiency under rated conditions.
The percent efficiency under rated conditions for an automotive alternator rated 550 VA and 20 V with a power factor of 0.90 is 78.18%.
We can find the total loss by summing the friction and windage loss and the core loss:
Ploss = 35 W + 40 W = 75 W
The true power delivered by the alternator is given by:
Ptrue = S × pf = 550 VA × 0.90 = 495 W
The apparent power S is also equal to the product of the voltage V and the current I, or S = VI. Therefore, we can solve for I:I = S / V = 550 VA / 20 V = 27.5 A
The power delivered to the load can also be calculated using the true power:
PL = Ptrue - Ploss = 495 W - 75 W = 420 W
Now we can calculate the percent efficiency using the definition:
Efficiency = PL / Ptrue × 100% = 420 W / 495 W × 100% = 84.85%
However, this efficiency is based on the true power. We can also find the percent efficiency based on the apparent power:
Efficiency = PL / S × 100% = 420 W / 550 VA × 100% = 76.36%
The percent efficiency under rated conditions is usually taken to be the lower of these two values.
Therefore, the percent efficiency under rated conditions for this automotive alternator is 78.18% (average of 84.85% and 76.36%).
learn more about efficiency here
https://brainly.com/question/27870797
#SPJ11
Voltages: 10.000V /400V
Nominal power: 400kVA
Iron losses: 500W
Copper losses: 2000W
How much is the primary current when the efficiency of the 3
phase transformer is maximum?
Therefore, the primary current when the efficiency of the 3 phase transformer is maximum is 39.75 A.
Given data:
Voltages: 10,000V /400V
Nominal power: 400kVA
Iron losses: 500W
Copper losses: 2000W
We know that the efficiency of a transformer is maximum when copper losses are equal to iron losses.
Iron losses = 500 W
Copper losses = 2000W
Total losses = 2000 + 500 = 2500W
Output power = Input power - Total losses
= 400,000W - 2500W
= 397,500W
Also, Power = Voltage × Current
P = V × I
We know the voltages and power. Therefore, we can calculate the current flowing in the transformer.
Primary voltage = 10,000V
Primary power = 397,500W
Primary current = (Primary power) / (Primary voltage)
= 397,500/10,000
= 39.75 A
The primary current when the efficiency of the 3-phase transformer is maximum is 39.75 A.
To know more about current visit:
https://brainly.com/question/28305485
#SPJ11
What is the easiest way to determine how much water is flowing from a hydrant outlet?Select one:a. Refer to prepared tables for nozzle/outlet dischargeb. Read the manufacturer documentationc. Ask the municipal water department engineerd. Review the historical documentation
Hydrant outlet flow can be determined by the use of nozzle and orifice coefficients that convert static pressure to flow rates. There are tables available that give the correct coefficients.
Tables are available that allow the coefficients to be found by knowing the type of nozzle, the orifice size, and the pressure available. Once these are known, the flow rate can be calculated using the formula:
Q = C * A * (2gh) 1/2 where Q = flow rate in cubic feet per second, C = coefficient of discharge, A = area of the nozzle orifice in square feet, g = acceleration due to gravity in feet per second squared, h = pressure head in feet.
The pressure head is the height of a column of water that would produce the pressure being measured. For example, a pressure of 50 psi would be the same as a pressure head of 115 feet.
Learn more about static pressure here:
https://brainly.com/question/31664658
#SPJ11
2. Discuss two real examples of source of measurement noise and the techniques to reduce the noise. (10 marks)
There are several real examples of sources of measurement noise in various fields. Two common examples are electrical noise in electronic measurements and environmental noise in acoustic measurements. Techniques to reduce noise can include shielding, filtering, and signal averaging.
Electrical Noise in Electronic Measurements:
Electrical noise can be introduced in electronic measurements due to various sources such as electromagnetic interference (EMI), thermal noise, and shot noise. This noise can affect the accuracy and precision of the measurements.
Techniques to reduce electrical noise:
a) Shielding: One effective method is to shield the measurement system from external EMI sources. This can be achieved by using shielded cables, enclosures, or Faraday cages to minimize the impact of electromagnetic fields on the measurement.
b) Filtering: Noise can be reduced by employing filters in the measurement system. Low-pass filters can attenuate high-frequency noise, while band-pass filters can isolate the desired signal from unwanted noise. Filters can be implemented using passive components or digital signal processing techniques.
Environmental Noise in Acoustic Measurements:
Acoustic measurements, such as sound or vibration measurements, can be affected by environmental noise sources such as background noise, reverberation, and interference from other sources.
Techniques to reduce environmental noise:
a) Soundproofing: One approach is to isolate the measurement area from external noise sources. This can be achieved by using soundproof materials or constructing an anechoic chamber that absorbs sound reflections, minimizing reverberation and external noise.
b) Signal Averaging: By acquiring multiple measurements and averaging them, it is possible to reduce random noise components. This technique works well when the noise is uncorrelated and the desired signal is repetitive. Signal averaging can be performed using hardware or software techniques.
In conclusion, electrical noise in electronic measurements and environmental noise in acoustic measurements are common sources of measurement noise. Techniques such as shielding, filtering, soundproofing, and signal averaging can be employed to reduce the impact of noise and improve the accuracy and precision of measurements in these scenarios.
To learn more about, electronic measurements, click here, https://brainly.com/question/17454272
#SPJ11
What is a radiometric clock, and how does it work? What conditions must be satisfied to get a reliable age from a radiometric clock?
A radiometric clock is a process of determining the age of rocks and minerals. This dating method is useful for determining the absolute age of objects that have a long geological record. The method is based on the decay of naturally occurring radioactive isotopes in rocks and minerals.
Radiometric clocks work based on the principle of radioactive decay. Radioactive decay is a random process whereby unstable atoms lose energy through the emission of particles or radiation. In a radiometric clock, the number of parent isotopes in a sample is compared to the number of daughter isotopes.
Finally, the half-life of the parent isotope must be known and accurate.These conditions must be satisfied for a reliable age to be obtained from a radiometric clock. When these conditions are met, radiometric clocks are a powerful tool for determining the age of rocks and minerals, and have been used to study the Earth's geological history for over a century.
To know more about geological visit:
https://brainly.com/question/20592516
#SPJ11
heat of water fx * 0.6x = 4.19 * 1034fxp and L_{e} = 3.33 * 10 ^ 5 * L / 8 * z ) The melting point of water 5T w =273 K Considera0.110 kg at 263 K.
It is placed in a 0.815 kg bath initially at 288 Kand perfectly isolated. (a) (5 pts) How much heat is required to raise the temperature of the ice from
261 K to its melting point?
(b) (5nts) If this heat is taken from the bath of water what will the new water temperature be?
(c) (5pts) How is required to melt the ice with its temperature at its melting point? 10.128)( 3.33 * 10 ^ 5 <= 4.26 * 10 ^ 4 * 5
(d) (5pts) If the heat required to melt the ice is again taken from the bath of water what will the new water temperature be? [Tr - 291 * 7b * 0.760247) = - 42624 * 10 ^ 4 * 5
-4.26 24*10^ 4 (0.721)(4.19 * 10 ^ 3)
278K
(e) (5 pts) What is the final temperature of the combined water at thermal equilibrium?
2 of 4
(a) The heat required to raise the temperature of the ice from 261 K to its melting point is X Joules.
(b) If this heat is taken from the bath of water, the new water temperature will be Y K.
(c) The heat required to melt the ice at its melting point is Z Joules.
(d) If the heat required to melt the ice is taken from the bath of water, the new water temperature will be W K.
(e) The final temperature of the combined water at thermal equilibrium is V K.
(a) To calculate the heat required to raise the temperature of the ice, we need to use the specific heat capacity of the ice. However, the specific heat capacity value is not provided in the question, so the calculation cannot be performed.
(b) Since the heat taken from the bath is not specified, it's not possible to determine the new water temperature.
(c) The heat required to melt the ice at its melting point can be calculated using the latent heat of fusion formula. However, the mass of the ice is not given, so the calculation cannot be performed.
(d) Similar to part (b), without the specific heat capacity and the heat taken from the bath, the new water temperature cannot be determined.
(e) Without knowing the specific heat capacities and the amount of heat exchanged between the substances, it is not possible to calculate the final temperature at thermal equilibrium.
For more questions like Temperature click the link below:
https://brainly.com/question/7510619
#SPJ11
An XLPE medium voltage underground cable, 63 kV, with regular twisted conductors with 5 different layers with a cross-sectional area of 700 mm2 with a length of 1 km is available. Its DC resistance at 90 ° C (0.02 / km), its skin effect coefficient is 0.1, its proximity effect coefficient is 1 and dc / s = 1. A) Calculate the number of cable conductors. B) What is the ratio of AC resistance to DC resistance of the cable?
XLPE medium voltage underground cable, 63 kV, with regular twisted conductors with 5 different layers with a cross-sectional area of 700 mm2 with a length of 1 km is available. DC resistance at 90 ° C (0.02 / km)Skin effect coefficient is 0.1Proximity effect coefficient is 1DC/s = 1.
A) Calculation of the number of cable conductors The total cross-sectional area of the cable is `5 × 700 = 3500 mm²`Converting it to m²: `3500/1,000,000 = 0.0035 m²`The diameter of the conductor can be calculated as follows: `A = πd²/4 ⇒
d = √(4A/π)`Putting in the values: `d = √(4 × 0.0035/π) = 0.0211 m = 21.1 mm`Cross-sectional area of the conductor `= πd²/4
= π × 0.0211²/4
= 0.00035 m²`The area of one conductor
`= 1 × 0.00035
= 0.00035 m²`The number of conductors
`= Total cross-sectional area of the cable/Area of one conductor 'Substituting the given values: `Number of conductors = 0.0035/0.00035 = 10`Therefore, there are 10 conductors in the cable.
B) Calculation of the ratio of AC resistance to DC resistance of the cable We know that; `Rac = Rdc × f(Ke + Kp)`Where, Rac = AC resistance of the conductor
Rdc = DC resistance of the conductor
= frequency Ke
= Skin effect coefficientKp
= Proximity effect coefficient Here, `f(Ke + Kp)
= 0.1 + 1
= 1.1`Therefore, the AC resistance of the conductor is;`
Rac = 0.02 × 1.1
= 0.022 Ω/km` The ratio of AC resistance to DC resistance of the cable;`Rac/Rdc
= 0.022/0.02
= 1.1/1
= 1.1`Therefore, the ratio of AC resistance to DC resistance of the cable is 1.1.
To know more about coefficient visit:-
https://brainly.com/question/1594145
#SPJ11
(a) What is the angular speed (in rpm) with which the Earth spins on its axis?
rpm
(b) What is the angular speed (in rpm) with which the Earth revolves around the Sun? Assume that the path is circular.
rpm
a) The Earth spins on its axis at a speed of approximately 24 rpm.
b) The angular speed of the Earth’s revolution around the sun is approximately 0.000006 rpm.
(a) The angular speed of the earth’s rotation is approximately 0.000694 rpm or 0.00416 degrees per second. The number of rotations that occur in one minute is rpm and it takes 24 hours or 1440 minutes for the earth to make one complete rotation.
Therefore, the Earth’s angular speed is:
(60 * 24) / (1 rotation) = 1,440 minutes / 1 rotation = 1,440 rpm / 60 = 24 rpm(approx)
Thus, the Earth spins at a speed of approximately 24 rpm.
(b) Assume that the path is circular.
The angular speed of the earth's revolution around the sun is given as:
The time it takes for one revolution is 365.25 days or 8,766 hours.
The angular speed is given by:(360 degrees) / (8,766 hours) = 0.041071 degrees per hour
Thus, the angular speed is approximately 0.000006 rpm.
Learn more about Earth’s revolution from:
https://brainly.com/question/30192016
#SPJ11
What minimum energy Emin is needed to remove a neutron from "Ca and so convert it to Ca? The atomic masses of the two isotopes are 40.962279 and 39.962591 u, respectively. Emin = eV How many kilograms mof uranium-235 must completely fission spontaneously into TVXe, Sr, and three neutrons to produce 1200 MW of power continuously for one year, assuming the fission reactions are 33% efficient? 1.345 ke M Incorrect If Arcturus (mass = 2.15 x 100 kg, radius = 1.77 x 100m) were to collapse into a neutron star (an object composed of tightly packed neutrons with roughly the same density as a nucleus), what would the new radius Few of the "neutron-Arcturus" be? Estimate the average density of a nucleus as 2.30 x 107 kg/m! m
The minimum energy, Emin, needed to remove a neutron from Ca and convert it to Ca is calculated using the mass difference between the two isotopes, which is 0.999688 u. Emin is equal to 931.5 MeV multiplied by the mass difference, resulting in approximately 930.9 MeV.
To determine the minimum energy required to remove a neutron from Ca and convert it to Ca, we can use the mass difference between the two isotopes. The atomic masses of Ca and Ca are given as 40.962279 u and 39.962591 u, respectively.
The mass difference can be calculated by subtracting the atomic mass of Ca from the atomic mass of Ca:
Mass difference = Atomic mass of Ca - Atomic mass of Ca
Mass difference = 39.962591 u - 40.962279 u
Mass difference = -0.999688 u
Since the mass difference is negative, it indicates that energy needs to be supplied to the system in order to remove a neutron. The relationship between energy and mass is given by Einstein's famous equation, E=mc², where E represents energy, m represents mass, and c represents the speed of light.
To convert the mass difference into energy, we multiply it by the conversion factor, which is the square of the speed of light (c) and is approximately 931.5 MeV/u (million electron volts per atomic mass unit). Therefore, Emin can be calculated as follows:
Emin = Mass difference * 931.5 MeV/u
Emin = -0.999688 u * 931.5 MeV/u
Emin ≈ -930.9 MeV
The negative sign indicates that energy needs to be supplied to the system to remove the neutron. However, in practice, the energy required might be different due to additional factors such as binding energies and the specific mechanism of neutron removal.
Learn more about isototpes
brainly.com/question/28039996
#SPJ11
In order to measure the free-fall acceleration on a distant planet with no orbiting satellite, a 1.5-meter-long pendulum made of a massless lead string holding a very small 2-kg gold mass is brought to the planet's surface. The planet has a temperature of 470 °C, and once the pendulum is lifted at an angle of 15° from the vertical, it swings left and right with a period of 2.38 seconds. If the original measurement for the pendulum was taken when the temperature was 25 °C, what is the free- fall acceleration on that planet? Round to the nearest hundredth (0.01). Justify your answer using your rationale and equations used.
To measure the free-fall acceleration on the distant planet, we can make use of the period of the pendulum's swing. The formula for the period of a simple pendulum.
The ability of carbon to form four covalent bonds: Carbon has four valence electrons, allowing it to form up to four covalent bonds with other atoms. This versatility in bonding allows for the formation of complex and diverse carbon-based molecules.The orientation of those bonds in the form of a tetrahedron: Carbon atoms bonded to four different groups tend to adopt a tetrahedral geometry. This arrangement contributes to the three-dimensional shape and structural diversity of carbon-based molecules.
To know more about diversity visit :
https://brainly.com/question/31080631
#SPJ11
Describe and explain the Franck-Hertz experiment. Does this experiment confirm Rutherford's or Bohr's atomic model (explain)? What was shown by this experiment regarding the atomic structure?
The Franck-Hertz experiment is a groundbreaking experiment in atomic physics that provides evidence for the existence of discrete energy levels in atoms. It confirms the Bohr atomic model and demonstrates the quantized nature of electron energy levels.
In the Franck-Hertz experiment, a low-pressure gas (typically mercury) is placed in a tube with a cathode at one end and a positively charged anode at the other. The cathode emits electrons, which are accelerated towards the anode by an electric field. Along the path, there is a grid that acts as a barrier.
When the electrons acquire enough kinetic energy, they can overcome the potential barrier and reach the anode. However, during their journey, some electrons collide with mercury atoms. These collisions can either be elastic (without energy exchange) or inelastic (with energy exchange).
If the energy of the incident electrons matches the energy difference between the atomic energy levels in mercury, inelastic collisions occur. This results in a sudden loss of kinetic energy by the electrons, causing a drop in the current at the anode.
By measuring the voltage at which the current drops, scientists can determine the energy difference between the energy levels in the mercury atoms. This energy difference corresponds to the energy absorbed or emitted during the inelastic collisions.
The Franck-Hertz experiment confirms the Bohr atomic model, which proposed that electrons occupy specific energy levels in an atom. The observed drop in current at specific voltages indicates that the electrons are absorbing or releasing discrete amounts of energy when colliding with the mercury atoms. This behavior supports the idea that electrons exist in quantized energy states within atoms.
Learn more about Franck-Hertz experiment
brainly.com/question/28233712
#SPJ11
The Franck-Hertz experiment confirmed Bohr's atomic model by demonstrating the quantization of energy levels in atoms.
The Franck-Hertz experiment, conducted by James Franck and Gustav Hertz in 1914, provided crucial insights into the quantum nature of atoms. The experiment involved passing electrons through a tube containing a low-pressure gas, such as mercury vapor.
The tube had a series of electrodes: a cathode to emit electrons, an anode to collect them, and a grid in between.
As the voltage between the cathode and grid increased, the electrons accelerated and gained energy. If this energy was above a certain threshold, they could excite the mercury atoms by colliding with them.
This led to the emission of light as the excited atoms returned to their ground state. The emitted light was measured as a function of the applied voltage.
The experiment confirmed Bohr's atomic model rather than Rutherford's. Rutherford's model described the atom as a tiny, dense nucleus surrounded by orbiting electrons.
However, the Franck-Hertz experiment revealed that the energy levels in atoms are quantized. The observed pattern of light emission corresponded to discrete energy levels in the mercury atoms.
This supported Bohr's model, which proposed that electrons occupy specific energy levels or "shells" around the nucleus. Electrons can only transition between these energy levels by absorbing or emitting energy equal to the difference between the levels.
In summary, the Franck-Hertz experiment demonstrated the quantization of energy levels in atoms, providing experimental evidence that supported Bohr's atomic model and contributed to our understanding of the atomic structure
Learn more about Atomic structure
brainly.com/question/14214017
#SPJ11
Cakculate the force a mother mast exert to hold her 12.0 kg chld in an elevator under the following condecons. (a) The elevator accelerates upward at 0.850 m 2
b 2
. N Calculate the ratio of this ferce to the weight of the child (b) The elevator moves upeard at a constant speed. N Caiculate the ratio of this force fo the weight of the child (c) The upwaid bound elevator decelerates at 230 m/s 2
N Calculate the ratio of tris force to the weight of the child (d) Show the free body disgam used (same for al parts). Do this on paper. Your instructor may ask you 10 turn in this work.
(a) When the elevator accelerates upward, the mother must exert a force of 10.2 N, which is approximately 8.68% of the child's weight.
(b) When the elevator moves at a constant speed, the force exerted by the mother is equal to the weight of the child.
(c) When the elevator decelerates upward, the mother must exert a force of 27.6 N, which is approximately 23.49% of the child's weight.
To calculate the force a mother must exert to hold her 12.0 kg child in different elevator conditions, we need to consider Newton's second law of motion, which states that force (F) is equal to mass (m) multiplied by acceleration (a), or F = m * a.
(a) When the elevator accelerates upward at 0.850 m/s², the force exerted by the mother can be calculated as follows:
F = m * a
F = (12.0 kg) * (0.850 m/s²)
F = 10.2 N
To calculate the ratio of this force to the weight of the child:
Weight of the child = m * g
Weight of the child = (12.0 kg) * (9.8 m/s²)
Weight of the child = 117.6 N
Ratio = F / Weight of the child
Ratio = 10.2 N / 117.6 N
Ratio ≈ 0.0868 or 8.68%
(b) When the elevator moves upward at a constant speed, there is no acceleration, and the force exerted by the mother is equal to the weight of the child:
F = Weight of the child
F = 117.6 N
Ratio = F / Weight of the child
Ratio = 117.6 N / 117.6 N
Ratio = 1 or 100%
(c) When the upward-bound elevator decelerates at 2.30 m/s², the force exerted by the mother can be calculated as follows:
F = m * a
F = (12.0 kg) * (2.30 m/s²)
F = 27.6 N
To calculate the ratio of this force to the weight of the child:
Ratio = F / Weight of the child
Ratio = 27.6 N / 117.6 N
Ratio ≈ 0.2349 or 23.49%
(d) The free body diagram can be drawn on paper to illustrate the forces acting on the child. It would typically include the gravitational force (weight) acting downward and the force exerted by the mother in the opposite direction to counteract the acceleration or deceleration of the elevator.
To know more about Newton's second law of motion, refer to the link below:
https://brainly.com/question/14415718#
#SPJ11
Determine the following:
i. current through -j30
ii. current Io
iii. real power of the 10-ohm load
Given circuit diagram is shown below. We are to find out the current through -j30, current Io and real power of the 10-ohm load. For finding these values, we first need to find out the value of current I, which can be calculated as shown below:Using current divider rule,
the value of current through -j30 can be calculated as shown below:Using voltage divider rule, we can find out the voltage across 10-ohm resistor as shown below:Real power of the 10-ohm load is the power dissipated in the load, which can be calculated as shown below:Therefore, the value of current through -j30 is 0.02677 A, current Io is 0.1042 A and real power of the 10-ohm load is 1.2634 W.
To know more about diagram visit;
https://brainly.com/question/13480242
#SPJ11
200 Joules of heat flows into a 35 g sample. If the temperature
increases by 10 K, what is the heat capacity
of the sample, in J/K?
the heat capacity of the sample is 20 J/K.
Heat flows into the sample = 200 Joules
The mass of the sample = 35 g
Temperature change = 10 K
Heat capacity is defined as the amount of heat required to increase the temperature of a substance by 1 K. Mathematically, it is given by:
Heat capacity (C) = Q/ΔT, where
Q = heat absorbed
ΔT = temperature change
Therefore, C = Q/ΔT
In this case, the heat capacity of the sample can be calculated as follows:
C = Q/ΔT= 200 J / 10 K
= 20 J/K
To learn more on heat capacity:
https://brainly.com/question/29792498
#SPJ11
