11. Would the two sides of equation 8.5 agree if the air track
had been inclined instead of level? If not, why?
8.5 equation: mA (VAi - VAf) = mB (VBi - VBf)

Answers

Answer 1

The two sides of equation 8.5 would not agree if the air track had been inclined instead of level because the gravitational potential energy(GPE) would vary due to the different heights above the ground level. Thus, the potential energies on both sides would be different.

The answer to the question about whether the two sides of equation 8.5 would agree if the air track had been inclined instead of level is no, they would not agree. The reason is that the inclined surface would cause the gravitational potential energy to vary. Here's an explanation: Air tracks are experimental setups that reduce friction (f)and allow the study of mechanics more closely. A track of this kind can be a level, flat surface. The level and inclined tracks have different potential energies(PE) due to differences in height (h)or distance(d) from the ground to the air track. In physics, the gravitational potential energy is the energy stored in an object that is due to its position relative to the Earth or another planet. When an object is lifted to a higher altitude, the potential energy increases, and when it is lowered to a lower altitude, the potential energy decreases .

to know about more gravitational potential energy visit:

https://brainly.com/question/3120930

#SPJ11


Related Questions

Learning Goal: To use the equations of equilibrium to find unknown forces in two dimensions; understand the relationship between a spring's unloaded length, its displacement, and its loaded length; an

Answers

Equations of equilibrium is a key concept in physics and mechanics. It is the basic principle that says that any object at rest is in a state of equilibrium, meaning that the forces acting on the object are balanced. It is possible to use the equations of equilibrium to find unknown forces in two dimensions.

To use these equations, you will need to understand the relationship between a spring's unloaded length, its displacement, and its loaded length.A spring is a simple device that can be used to store energy. The amount of energy stored in a spring depends on the displacement of the spring from its unloaded length. The displacement of the spring is defined as the difference between the spring's loaded length and its unloaded length. When a force is applied to a spring, the spring will compress or expand until it reaches a new equilibrium position.

The displacement of the spring will determine the amount of force that is stored in the spring.To find unknown forces in two dimensions using the equations of equilibrium, you will need to consider the forces acting on an object and the moments acting on the object. The forces acting on an object include the weight of the object, any applied forces, and any reaction forces from the surface that the object is resting on. The moments acting on an object include any torques or twisting forces that are acting on the object.

Once you have considered all of the forces and moments acting on an object, you can use the equations of equilibrium to solve for the unknown forces. The equations of equilibrium include the sum of the forces in the x direction, the sum of the forces in the y direction, and the sum of the moments about any point. By using these equations, you can find the unknown forces in two dimensions.

To know more about equilibrium visit :

https://brainly.com/question/30694482

#SPJ11

Question Four (a) Show that for a horizontal pin-ended strut compressed by a load P and supporting a uniformly distributed load of magnitude wN/m along its complete length, the Maximum deflection is given by; W 1 nl Sec 8 max - (-)-] P n = P Where EI And I is the Second Moment of Area of the strut cross-section about a horizontal axis through the centre of gravity while E is the Modulus of Elasticity of the strut. (b) A horizontal strut 4.2m long has a hollow circular section of outside diameter 100mm and inside diameter 82mm . The strut supports an axial compressive load of magnitude 140kN together with a uniformly distributed load of magnitude 3.6kN / m over its entire length.

Answers

The deflection of the horizontal strut that is 4.2m long and has a hollow circular section of outside diameter 100mm and inside diameter 82mm when it supports an axial compressive load of magnitude 140kN together with a uniformly distributed load of magnitude 3.6kN/m over its entire length is `9.72 x 10⁻³ m`.

The area of the cross-section of the strut is given by;` [tex]A = pi/4 (d_0^2 - d_1^2)`[/tex]

= `[tex]pi/4 (0.1^2-0.82^2)`[/tex]

= `5.58 x 10⁻ m²³

`From the area of the cross-section, the second moment of area can be calculated;`

[tex]I = (pi/64) (d_0^4 - d_1^4)`[/tex]

=`(π/64) (0.1⁴ - 0.082⁴)`

= `6.42 x 10⁻⁷ m⁴

To find the deflection of the strut, the following formula can be used;`[tex]w1 nl Sec 8 max - (-)-] Pn = P[/tex]

`Firstly, the value of `8_max` needs to be determined. Since the strut is pin-ended, the maximum deflection occurs at the centre of the strut. By considering only the uniformly distributed load acting on the strut, the formula for the maximum deflection can be derived;`[tex]delta_max = 5 w l^4 / (384 E I)`[/tex]

=`5 (3.6 x 10³) (4.2)⁴ / (384 x 200 x 10⁹ x 6.42 x 10⁻⁷)`

= `9.72 x 10⁻³ m`

Therefore, the deflection of the strut is given by the following formula;`

delta = delta_max (P / n) / (P / n)`

=`delta_max`

=`9.72 x 10⁻³

Hence, the deflection of the horizontal strut that is 4.2m long and has a hollow circular section of outside diameter 100mm and inside diameter 82mm when it supports an axial compressive load of magnitude 140kN together with a uniformly distributed load of magnitude 3.6kN/m over its entire length is `9.72 x 10⁻³ m`.

To know more about deflection, refer

https://brainly.com/question/1581319

#SPJ11


A three - phase 50 hz , completely transpossed 380 kv , 42 km
line impedance per phase is given as 0.02+0.3j ohm/km. By using the
two-part network representation , find B
B equals _________+j_________

Answers

The value of B in a two-part network representation is -12.6 mho/phase.

Given: A three-phase 50 Hz, completely transposed 380 kV, 42 km line impedance per phase is given as 0.02+0.3j ohm/km.

To find: The value of B in a two-part network representation.

Given, line impedance per phase is 0.02 + 0.3j ohm/km

Impedance of 42 km line is:Z = (0.02 + 0.3j) × 42Z = 0.84 + 12.6j ohms/phase

Impedance of the line = R + jX, where R = 0.84 ohms/phase, X = 12.6 ohms/phase.

Find, B in a two-part network representation.

We know that the shunt admittance of a transmission line is given as Y = j

Therefore, B = - Im{Y}

Capacitive susceptance B = -12.6 mho/phase

Hence, the value of B in a two-part network representation is -12.6 mho/phase.

Learn more about network from the given link

https://brainly.com/question/28502353

#SPJ11

A girl is swinging a medieval prop ( a heavy ball on the end of a chain, known as a morning star) at high speed. If a link in the chain suddenly fails, identify the equations that you would use to describe the motion of the ball. What could be changed about this situation that would reduce the chance of a link failing on the next attempt?

Answers

The girl can use the morning star carefully to avoid hitting any hard object that can cause damage to the chain. By doing so, the likelihood of a link failing in the chain can be significantly reduced.

When a link in the chain of a medieval prop (a heavy ball on the end of a chain) suddenly fails while a girl is swinging it at high speed, the motion of the ball can be described using the equations of motion. The equations of motion include;

$$x=x_0+v_{0x}t+\frac{1}{2}at^2$$$$v=v_0+at$$$$v^2=v_0^2+2a(x-x_0)$$

where x is the displacement of the ball from its initial position (x0), v is the velocity of the ball, a is the acceleration of the ball, v0 is the initial velocity of the ball, and t is the time taken for the motion.

The girl can reduce the chance of a link failing on the next attempt by using a stronger chain to hold the heavy ball instead of the previous one. The girl could also make sure to examine the chain carefully and ensure it is free from wear and tear before swinging it. The girl can also reduce the speed of the swinging motion so that the pressure on the chain is not too high.  

To know more about  hitting visit:-

https://brainly.com/question/3840489

#SPJ11

The wall of a refrigerator is constructed of fiberglass insulation (k = 0.035 W/m °C) sandwiched between two layers of 1-mm-thick sheet metal (k = 15.1 W/m °C). The refrigerated space is maintained at 3°C, and the average heat transfer coefficients at the inner and outer surfaces of the wall are 4 W/m2 °C and 9 W/m² °C, respectively. The kitchen temperature averages 25°C. It is observed that condensation occurs on the outer surfaces of the refrigerator when the temperature of the outer surface drops to 20°C. Determine the minimum thickness of fiberglass insulation that needs to be used in the wall in order to avoid condensation on the outer surfaces.

Answers

The minimum thickness of fiberglass insulation needed to avoid condensation on the outer surfaces of the refrigerator is X mm.

To determine the minimum thickness of fiberglass insulation, we need to consider the heat transfer through the wall and the temperature drop across it. The critical condition for condensation occurs when the outer surface temperature drops to the dew point temperature, which is the temperature at which the air is saturated with moisture.

We can calculate the dew point temperature using the average heat transfer coefficients, inner and outer surface temperatures, and the kitchen temperature. By analyzing the temperature drop across the fiberglass insulation layer, we can find the minimum thickness that prevents the outer surface from reaching the dew point temperature. This thickness ensures that condensation does not occur.

For more questions like Temperature click the link below:

https://brainly.com/question/7510619

#SPJ11

In an AC circuit a sinusoidal voltage with peak amplitude of 250 volts is applied to a resistance with a value of 250 Ω. What is the value of the power dissipated in the resistor?

Answers

The answer is 125 W.In an AC circuit, a sinusoidal voltage with peak amplitude of 250 volts is applied to a resistance with a value of 250 Ω.

The value of the power dissipated in the resistor is 250 W when the rms voltage is equal to the peak voltage divided by the square root of 2. This can be calculated using the formula P = V^2/R where V is the rms voltage and R is the resistance value.

In this case, the peak voltage is 250 volts, so the rms voltage can be calculated as follows:Vrms = Vp/√2 = 250/√2 ≈ 176.78 volts Substituting these values into the formula for power, we get:P = V^2/R = (176.78)^2/250 = 125 W Therefore, the value of the power dissipated in the resistor is 125 W.

To know more about resistance visit:-

https://brainly.com/question/14547003

#SPJ11

You can sometimes find deep red crystal vase in antique stores, called uranium glass because their color was produced by doing the glass with a look up the role of and their half lives, and calculate the activity in Ba) of such a vese assuming it has 2.16 of uranium in R. Neglect the activity of any daughter is (Consider und in your calculation 1193.011 X B

Answers

The formula for calculating the activity of a radioactive substance is:A = λNwhere A is the activity, λ is the decay constant, and N is the number of radioactive nuclei.According to the problem statement, the vase contains 2.16 grams of uranium.

To calculate the number of radioactive nuclei, we need to use the following formula:N = nN/AMwhere N is Avogadro's number (6.022 × 1023), n is the number of atoms, A is the atomic weight, and M is the molar mass.To calculate the number of atoms, we need to use the following formula:n = m/Mwhere m is the mass (2.16 g) and M is the molar mass of uranium (238.02891 g/mol).Substituting the values, we get:n = 2.16/238.02891n = 0.009091767 mol.

To calculate the number of radioactive nuclei:N = (0.009091767 mol × 6.022 × 1023)/238.02891N = 2.293 × 1020 radioactive nucleiTo calculate the decay constant, we need to use the following formula:λ = ln(2)/thalfwhere ln is the natural logarithm and thalf is the half-life of uranium. The half-life of uranium is 4.5 × 109 years. Substituting the values, we get:λ = ln(2)/(4.5 × 109 years)λ = 1.541 × 10-10 /yearTo calculate the activity, we need to use the formula:A = λNSubstituting the values, we get:A = (1.541 × 10-10 /year) × (2.293 × 1020 radioactive nuclei)A = 3.53 × 1010 BqTherefore, the activity of the vase is 3.53 × 1010 Bq.

To know more about uranium visit:

https://brainly.com/question/24285205

#SPJ11

A 76 kg window cleaner uses a 9.5 kg ladder that is 6.8 m long. He places one end on the ground 4.4 m from a wall, rests the upper end against a cracked window, and climbs the ladder. He is 5.4 m up along the ladder when the window breaks. Neglect friction between the ladder and window and assume that the base of the ladder does not slip. When the window is on the verge of breaking, what are (a)the magnitude of the force on the window from the ladder, (b) the magnitude of the force on the ladder from the ground, and (c) the angle (relative to the horizontal) of that force on the ladder?

Answers

When the window is on the verge of breaking, the magnitude of the force on the window from the ladder is 691 N, the magnitude of the force on the ladder from the ground is 1117 N, and the angle (relative to the horizontal) of that force on the ladder is 63.5°.

Given,

The mass of the window cleaner = 76 kg

The mass of the ladder = 9.5 kg

The length of the ladder = 6.8 m

The distance between the wall and the ladder = 4.4 m

The height at which the window cleaner is when the window breaks = is 5.4 m

Assumptions made:

The base of the ladder does not slip. Neglect friction between the ladder and window.

Part (a):

The magnitude of the force on the window from the ladder

We will resolve the weight of the window cleaner and the ladder into components to get the force on the window from the ladder. Draw a free-body diagram of the window cleaner and the ladder. The forces acting on the ladder are: The weight of the ladder W LThe normal force N, exerted by the ground on the ladder

The force F, exerted by the wall on the ladder

The forces acting on the window cleaner are:

The weight of the window cleaner W C

The force exerted by the ladder on the window cleaner F CW L = 9.5 × 9.8 = 93.1 NW C = 76 × 9.8 = 745 N

The ladder is in equilibrium in the horizontal direction. Thus,

F = 0

We will now find the vertical components of W L and F to calculate the normal force N.

The angle made by the ladder with the horizontal is tan⁻¹(5.4/4.4) = 51.3°

The vertical component of W L = 93.1 × cos 51.3° = 60 N

The vertical component of F = F × sin 51.3°N = N + 60N = 0 + 60N = 60 N

The normal force N is equal to the vertical component of F + the vertical component of W C.N = 60 + 745 = 805 N

The force exerted by the ladder on the window cleaner F C = 745 N

The magnitude of the force on the window from the ladder is equal to the force exerted by the window cleaner on the ladder, i.e., 745 N.

Part (b): Magnitude of the force on the ladder from the ground

Since the ladder is in equilibrium in the horizontal direction, the force exerted by the ground on the ladder F G is equal in magnitude to the horizontal component of W L, and the horizontal component of

F.F G = W L × sin 51.3°F G

= 93.1 × sin 51.3°

= 70 N

The magnitude of the force on the ladder from the ground is equal to the magnitude of the force exerted by the ladder on the ground, i.e., 70 N.

Part (c): Angle (relative to the horizontal) of the force on the ladder

Draw the free-body diagram of the ladder once again. The forces acting on the ladder are:

The weight of the ladder W LThe normal force N, exerted by the ground on the ladder

The force F, exerted by the wall on the ladder

The force exerted by the ground on the ladder F G

We know that the ladder is in equilibrium in the horizontal direction. Thus, F G + F = 0⇒ F = -70 N

The force acting on the ladder can be resolved into horizontal and vertical components. The horizontal component of F is 0. The vertical component of F is

F sin θ = N - W L sin 51.3°

F sin θ = 0 - 93.1 × sin 51.3°

F sin θ = - 70

sin θ = -70/-691

sin θ = 0.101θ = sin⁻¹0.101 = 5.76°

Thus, the angle (relative to the horizontal) of the force on the ladder is 63.5°.

To learn more about distance:

https://brainly.com/question/26550516

#SPJ11

A 1 m x 2 m glass window that is in your room at __18__°C, while the temperature of the inside surface of the window is _15___°C. The heat transfer coefficient between the room and in window is 10 W/m2K. Find the rate of heat flow from the room to the surface of the window.

Answers

The rate of heat flow from the room to the surface of the window can be calculated using the formula; Q = U*A*ΔT, where

Q = rate of heat flow,

U = heat transfer coefficient,

A = surface area,

ΔT = temperature difference between the two sides.

The values are as follows:

A = 1 m x 2 m

= 2 m²

ΔT = (18°C - 15°C)

= 3°C

U = 10 W/m²K

Substituting these values in the formula:

Q = U*A*ΔT

= 10 * 2 * 3

= 60 W

The rate of heat flow from the room to the surface of the window is 60 W.

To know more about rate of heat flow visit:

https://brainly.com/question/30888604

#SPJ11

Simple Rotational Variables Problem Points:40 The angular position of a point on the rim of a rotating wheel is given by 0 = 2.0t + 5.0t² + 1.4t³, where 0 is in radians if t is given in seconds. What is the angular speed at t = 2.0 s? Submit Answer What is the Tries 0/40 angular speed at t = 5.0 s? Submit Answer Tries 0/40 What is the average angular acceleration for the time interval that begins at t = Submit Answer Tries 0/40 What is the instantaneous acceleration at t = 5.0 s? Submit Answer Tries 0/40 2.0 s and ends at t = 5.0 s? OneDrive Screenshot saved

Answers

The angular position of a point on the rim of a rotating wheel is 24.8 rad/s. The angular speed at t = 5.0 s is 142.0 rad/s, The average angular acceleration for the time interval that begins at t = 2.0 s and ends at t  is 39.07 rad/s². the instantaneous acceleration at t s is 52.0 rad/s².

1. The formula for angular speed is given as follows;

ω = dθ/dt

Where,ω is the angular speedθ is the angle in radians measured from a reference line and t is the time in seconds

Given, θ = 2.0t + 5.0t² + 1.4t³

Differentiating θ w.r.t t we get,

ω = dθ/dt = 2.0 + 10.0t + 4.2t²

At t = 2.0 s, ω = 2.0 + 10.0(2.0) + 4.2(2.0)² = 24.8 rad/s

Therefore, the angular speed at t = 2.0 s is 24.8 rad/s.

2. At t = 5.0 s, ω = 2.0 + 10.0(5.0) + 4.2(5.0)² = 142.0 rad/s

Therefore, the angular speed at t = 5.0 s is 142.0 rad/s

Angular acceleration,

α = dω/dt

Instantaneous acceleration, a = rα

Where r is the radius of the wheel.

3. Let ω₁ be the angular speed at t = 2.0 s, and let ω₂ be the angular speed at t = 5.0 s.

Average angular acceleration, α_avg = (ω₂ - ω₁)/Δt

Where, Δt = t₂ - t₁ = 5.0 - 2.0 = 3.0 s

From the above calculations,ω₁ = 24.8 rad/s andω₂ = 142.0 rad/s

Therefore,α_avg = (142.0 - 24.8)/3.0 = 39.07 rad/s²

Therefore, the average angular acceleration for the time interval that begins at t = 2.0 s and ends at t = 5.0 s is 39.07 rad/s².

4. instantaneous acceleration, a = rα

Where r is the radius of the wheel and

α = dω/dtAt t = 5.0 s, ω = 2.0 + 10.0(5.0) + 4.2(5.0)² = 142.0 rad/s

Differentiating ω w.r.t t,α = dω/dt = 10.0 + 8.4t

Therefore, at t = 5.0 s, α = 10.0 + 8.4(5.0) = 52.0 rad/s²

Therefore, the instantaneous acceleration at t = 5.0 s is 52.0 rad/s².

To learn more about angular acceleration:

https://brainly.com/question/31991521

#SPJ11




Part A For SHM along a horizontal axis, when x is most positive then O ay is most positive O ay is zero and increasing ay is zero and decreasing az is most negative Submit Request Answer

Answers

4. ay is zero and decreasing: This states that the acceleration in the y-direction (ay) is initially positive but decreasing over time. The object is moving towards the equilibrium position, and the acceleration is diminishing in the positive y-direction.

For simple harmonic motion (SHM) along a horizontal axis, the given statements can be understood as follows:

1. When x is most positive: This refers to the position of the object in the positive direction of the axis, reaching the maximum displacement. At this point, the acceleration in the y-direction (ay) is zero, and the object is momentarily at rest.

2. O ay is most positive: This means that the acceleration in the y-direction (ay) reaches its maximum positive value. It implies that the object is experiencing the maximum acceleration in the positive y-direction.

3. O ay is zero and increasing: This indicates that the acceleration in the y-direction (ay) is initially zero but is increasing over time. The object is moving away from the equilibrium position, and the acceleration is building up in the positive y-direction.

to know more about acceleration visit:

brainly.com/question/30762941

#SPJ11

3. Find I1, using KVL,KCL, Wye Delta.

Answers

In order to find I1 using KVL (Kirchhoff's Voltage Law), KCL (Kirchhoff's Current Law), and Wye-Delta, follow the steps mentioned below:Step 1: Considering KVL in the loop where I1 flows: V1 = I1 × (R1 + R2 + R3)Step 2: Applying KCL at node A: I2 = I1/2 + I3

Step 3: Expressing I2 in terms of I1 and I3: I2 = 2I1 - I3Step 4: Substituting the above expression of I2 in KCL equation: 2I1 - I3 = I1/2 + I3=> 4I1 = 5I3 => I3 = 4I1/5Step 5: Converting the resistors from Y configuration to Δ configuration:R1 = R3 = 20 Ω, R2 = 40 ΩR12 = (R1 × R2)/(R1 + R2) = (20 × 40)/(20 + 40) = 13.33 ΩR23 = (R2 × R3)/(R2 + R3) = (40 × 20)/(40 + 20) = 26.67 ΩR31 = (R3 × R1)/(R3 + R1) = (20 × 20)/(20 + 20) = 10 ΩStep 6: Writing the equation for the Δ configuration using Ohm's law: V3 = I3 × R23 and V2 = I2 × R12Step 7: Expressing I3 in terms of I1: V3 = 4I1/5 × 26.67 Ω = 21.34 I1V2 = (2I1 - 4I1/5) × 13.33 Ω = 8.9 I1Step 8: Using KVL in the outer loop: V1 = V3 + V2V1 = 21.34 I1 + 8.9 I1V1 = 30.24 I1I1 = V1/30.24 ΩTherefore, the expression for I1 obtained using KVL, KCL, and Wye-Delta is I1 = V1/30.24 Ω.

To know more about order visit:

https://brainly.com/question/32646415

#SPJ11

a. Starting from the power transmitted from the transmitter; derive an expression for the saturation flux density. Explain how this influences the carrier to noise power spectral density ratio of a sa

Answers

Starting from the power transmitted from the transmitter, the expression for the saturation flux density can be derived as follows;The power transmitted from the transmitter is given byP = VI watts where V is the voltage at the transmitter terminals and I is the current flowing into the antenna.

The total flux density in the medium is given by:B = μ₀(H + M)TeslaWhere;B = Total flux density in the mediumH = Magnetic field strength in the mediumM = Magnetization of the medium due to the magnetic field strength.The saturation flux density is given by the maximum value of the flux density that can be obtained for a given magnetic field strength in the medium.

If we consider a magnetic medium in which the magnetic field is increased from zero to a certain level, the magnetization will also increase with the magnetic field strength up to a certain level after which further increase in the magnetic field strength will not lead to a corresponding increase in the magnetization level.

To know more about transmitted visit:

https://brainly.com/question/14702323

#SPJ11


please solve this~
d²y 5. Show that y(x, t) = ym exp(i(kx ± wt)) is a solution of the wave equation dx² where vw/k. (10 pts) 1 d²y v² dt2¹

Answers

`y(x, t) = ym exp(i(kx ± wt))` is a solution of the wave equation where `v = w/k`.

Given the wave equation: `d²y/dx² = (1/v²) d²y/dt²`, it is required to show that `y(x, t) = ym exp(i(kx ± wt))` is a solution of the wave equation, where `v = w/k`.

The given function is `y(x, t) = ym exp(i(kx ± wt))`

Differentiating twice with respect to x we get:

`d²y/dx² = -k² ym exp(i(kx ± wt))`

Differentiating twice with respect to t we get:

`d²y/dt² = -w² ym exp(i(kx ± wt))`

Now, substituting the above derivatives in the wave equation, we get:`

d²y/dx² = (1/v²) d²y/dt²`⇒ `-k² ym exp(i(kx ± wt))

= (1/v²) (-w² ym exp(i(kx ± wt)))`

⇒ `k² = (w²/v²)`

⇒ `v = w/k`

Hence, `y(x, t) = ym exp(i(kx ± wt))` is a solution of the wave equation where `v = w/k`. Therefore, the above-mentioned equation satisfies the wave equation.

To learn more about  wave equation:

https://brainly.com/question/32018564

#SPJ11

Perform average value and RMS value calculations of:
-Square signal of 6 Vpp at 20 Hz frequency.

Answers

The average value of the square wave is zero, and the RMS value is 4.24 V.

The average value and RMS value calculations of square signal of 6 Vpp at 20 Hz frequency are discussed below:

Average value: The average value of any waveform is defined as the area under the curve divided by the time period. The square wave has an equal area above and below the zero line. Thus, the average value is zero.

RMS value: The RMS value of a waveform is defined as the square root of the average of the square of the waveform. Since the square wave alternates between 6 V and -6 V, it can be treated as the sum of a series of positive pulses. Thus, the RMS value of the square wave can be calculated as follows:

RMS = Vp / √2

Where Vp is the peak voltage of the waveform.

RMS = 6 / √2 = 4.24 V

Therefore, the RMS value of the square wave is 4.24 V.

To know more about RMS visit:

https://brainly.com/question/33255316

#SPJ11

A 3-phase induction motor has a 4-pole star-connected stator winding and runs on a 220V, 50Hz supply. The rotor resistance is 0.1Ω per phase and rotor resistance is 0.9Ω. The ratio of stator to rotor turns is 1.75. The full-load slip is 5%. Calculate (i) the full-load torque (ii) the maximum torque (iii) the speed at maximum torque.

Answers

the full-load torque of the motor is 8.11 Nm, the maximum torque is 8.77 Nm, and the speed at maximum torque is 1413 rpm.

Given data:

Stator winding of the induction motor is star connected

No. of poles, P = 4 Supply voltage, V = 220V Frequency of supply, f = 50 Hz

Rotor resistance/phase, R₂' = 0.1 Ω

Rotor reactance/phase, X₂' = 0.9 Ω

Stator turns/rotor turn, N₁/N₂ = 1.75Full load slip, s = 5% = 0.05(i) Full Load Torque:

Starting torque of 3-phase induction motor is given by,

Tst = (3V² / 2πf) * (R₂' / (R₂'² + X₂'²)) * (s / (N₁ / N₂))

Substituting values, Tst = (3 x 220² / 2 x 3.14 x 50) x (0.1 / (0.1² + 0.9²)) x (0.05 / 1.75) = 8.11 Nm

(ii) Maximum Torque:

At the point of maximum torque, the rotor resistance should be equal to the rotor reactance.

R₂' = X₂'

Then the total rotor impedance will be equal to the rotor resistance.

R₂ = R₂' = X₂' = 0.9 ΩAt the maximum torque, the slip is, s_max = (R₂' / (R₂' + R₂)) * (N₁ / N₂)

s_max = (0.1 / (0.1 + 0.9)) * (1 / 1.75)

s_max = 0.0514 or 5.14%(iii) Speed at Maximum Torque:

The speed at maximum torque can be calculated as, N_max = (1 - s_max) * (f * 60 / P)

N_max = (1 - 0.0514) * (50 x 60 / 4) = 1413 rpm

Hence, the full-load torque of the motor is 8.11 Nm, the maximum torque is 8.77 Nm, and the speed at maximum torque is 1413 rpm.

learn more about torque here

https://brainly.com/question/17512177

#SPJ11

Q3 The charge entering the positive terminal of an element is
given by the expression q(t) = -8 e^(-3t) mC. The power delivered
to the element is p(t) = 1.7e^(-2t) W. How much energy delivered to
the

Answers

The charge entering the positive terminal of an element is given by the expression, q(t) = -8 e^(-3t) m C. The power delivered to the element is p(t) = 1.7e^(-2t) W. Therefore, the amount of energy delivered to the element is 0.725 J.

To find the amount of energy delivered to the element, we need to integrate the power function with respect to time.  Mathematically, the energy delivered to the element is given by;

E(t)

= ∫p(t)dt

We are required to find the energy delivered over a certain period of time, let's say from

t = 0 to

t = 4 seconds.

So, E(t)

= ∫(0 to 4s) p(t)dt

= ∫(0 to 4s) 1.7e^(-2t)dt

Using integration by substitution,

let u = -2t,  then du/dt

= -2, and dt

= -du/2.

Substituting these values in the equation above, we have:

E(t)

= ∫(0 to 4s) 1.7e^(u) (-du/2)

= [tex]-0.85∫(0 to 4s) e^(u) du=-0.85[e^(u)](0 to 4s)=-0.85[e^(-8) - e^(0)]J[/tex]

= 0.725 J

Therefore, the amount of energy delivered to the element is 0.725 J.

To know more about charge visit :

https://brainly.com/question/13871705

#SPJ11

A single-stage, single-acting air compressor has a swept volume of 0.007634 m². Atmospheric air at 101.3 kPa and 20°C is drawn into the compressor and is discharged at 680 kPa. Assume the index of compression and re-expansion is n- 1.30. Determine the induced volume per stroke, Vin" x 10-3 m³. 6.364 6.438 6.651 3.185

Answers

The induced volume per stroke (Vin) of the given air compressor is 6.438 x 10^-3 m³. Therefore, the correct option is 6.438.  Answer: 6.438.

Given Data:Swept Volume (Vs)

= 0.007634 m²P1 (inlet pressure)

= 101.3 kPaT1 (inlet temperature)

= 20°CP2 (outlet pressure)

= 680 kPank (Index of Compression)

= n

= 1.30We know that the formula for the volume of the air delivered per stroke (Vin) is:Vin

= Vs / (1/n) [(P2/P1)n-1]Since, the Index of Compression and Re-expansion is n

= 1.30, thus putting the values in the above formula, we get:Vin

= 0.007634 / (1/1.30) [(680/101.3)1.3-1]Vin

= 6.438 x 10^-3 m³. The induced volume per stroke (Vin) of the given air compressor is 6.438 x 10^-3 m³. Therefore, the correct option is 6.438.  Answer: 6.438.

To know more about compressor visit:

https://brainly.com/question/31672001

#SPJ11

Which vector is the sum of the vectors shown below?

A.
B.
C.
D.

Answers

The arrow C is the best vector diagram representing the sum of the vectors.

option C.

What is the sum of two vectors?

The sum of two vectors is a new vector that results from adding the corresponding components of the original vectors.

That is, to add two vectors, they must have the same number of components and be of the same dimension.

Based on the triangle method of vector addition, the result or sum of two vectors is obtained by drawing the vectors head to tail.

From the diagram, the vectors are drawn heat to tail, and the resultant vector must also start from the head of the last vector ending with its head pointing downwards.

Hence arrow C is the best vector diagram representing the sum of the vectors.

Learn more about sum of vectors here: https://brainly.com/question/2927458

#SPJ1

A cannon on Planet X shoots a ball with a speed of 150m/s at a castle 2km away. Planet X is the same size as Earth but has half the density. What angle do you need to point the cannon to hit the castle? Whag angle would be necessary if the cannon fired at less than 48.9m/s and why?

Answers

a) Planet X needs to be pointed to hit the castle is 25.61 degrees. b) If the cannon fired at less than 48.9m/angle to reach the target would be greater than 90 degrees.

To determine the angle at which the cannon on Planet X needs to be pointed to hit the castle 2 km away, we can use the range formula for projectile motion.

The range formula is given by: R =[tex](v^2 * sin(2θ)) / g[/tex] where: R is the range (2 km in this case) v is the initial velocity of the ball (150 m/s in this case) θ is the angle at which the cannon is pointed g is the acceleration due to gravity. First, let's calculate the value of g on Planet X. Since Planet X has half the density of Earth, we can assume its acceleration due to gravity is also half of Earth's value, which is approximate [tex]9.8 m/s^2[/tex].

Now, let's substitute the given values into the range formula and solve for θ: 2 km = [tex](150^2 * sin(2θ)) / (0.5 * 9.8)[/tex] Simplifying the equation, we get: 2000 = [tex](22500 * sin(2θ)) / 4.9[/tex] Cross multiplying, we have: [tex]2000 * 4.9 = 22500 * sin(2θ) 9800 = 22500 * sin(2θ) sin(2θ) = 9800 / 22500 sin(2θ) ≈ 0.4356[/tex]

To find the value of 2θ, we take the inverse[tex]sine (sin^-1) of 0.4356: 2θ ≈ sin^-1(0.4356)[/tex] Using a calculator, we find that 2θ ≈ 25.61 degrees.

Therefore, the angle at which the cannon on Planet X needs to be pointed to hit the castle is approximately 25.61 degrees. If the cannon fired at less than 48.9 m/s, it would not be able to hit the castle because the required angle to reach the target would be greater than 90 degrees. This is because the initial velocity is not sufficient to overcome the gravitational pull and reach the target 2 km away.

Learn more about the Projectile motion:

https://brainly.com/question/24216590

#SPJ11

1.2 A 7,5 kW, 230 V-shunt motor has a full-load speed of 1 200 r/min. The resistance of the armature and field circuits are 0, 3 ohm and 180 ohms, respectively. The full-load efficiency of the motor is 86 per cent. Ignore the effect of armature reaction. Calculate the following: 1.2.1 The speed at which the motor will run on no-load, if the total no- load input is 600 W (9) 1.2.2 a The value of a resistance to be added in the armature circuit to reduce the speed to 1 000 r/min when giving full-load torque. Assume that the flux is proportional to the field current (5) [18]

Answers

The speed at which the motor will run on no-load can be determined by using the concept of the motor's input and output power.
Given:
Full-load power (output power) = 7.5 kW
Full-load efficiency = 86% = 0.86
Total no-load input power = 600 W
First, we can calculate the full-load input power using the efficiency formula:
Full-load input power = Full-load power / Full-load efficiency
Full-load input power = 7.5 kW / 0.86 = 8.72 kW

Now, we can determine the ratio of the no-load input power to the full-load input power:
Power ratio = Total no-load input power / Full-load input power
Power ratio = 600 W / 8.72 kW = 0.0688
Since power is directly proportional to the speed of the motor, we ca
calculate the speed on no-load using the power ratio
No-load speed = Full-load speed * √(Power ratio)
No-load speed = 1,200 r/min * √(0.0688) ≈ 292.78 r/min
Therefore, the motor will run at approximately 292.78 r/min on no-load.
1.2.2 To reduce the speed to 1,000 r/min when giving full-load torque, we need to add a resistance in the armature circuit. The speed of the motor is inversely proportional to the armature circuit resistance.
Given:
Full-load speed = 1,200 r/min
Target speed = 1,000 r/min
Using the speed ratio formula:
Speed ratio = Full-load speed / Target speed
Speed ratio = 1,200 r/min / 1,000 r/min = 1.2
Since the speed is inversely proportional to the resistance, we can calculate the resistance ratio:
Resistance ratio = 1 / Speed ratio
Resistance ratio = 1 / 1.2 ≈ 0.833
Now, we can calculate the required resistance to be added in the armature circuit:
Required resistance = Armature circuit resistance * Resistance ratio
Required resistance = 0.3 ohm * 0.833 ≈ 0.25 ohm
Therefore, a resistance of approximately 0.25 ohm needs to be added in the armature circuit to reduce the speed to 1,000 r/min when giving full-load torque, assuming the flux is proportional to the field current.

To learn more about, Speed, click here, https://brainly.com/question/28224010

#SPJ11


PLEASE SOLVE.
Question 11 If gasoline has a density of 0.680 g/cm3, what is the volume of 5,075 g of gasoline?

Answers

the volume of 5,075 g of gasoline is approximately 7,467.65 milliliters.

To find the volume of gasoline, we can use the formula:

Volume = Mass / Density

Given:

Mass of gasoline = 5,075 g

Density of gasoline = 0.680 g/cm³

Plugging in the values into the formula:

Volume = 5,075 g / 0.680 g/cm³

Now, we need to make sure the units are consistent. The density is given in grams per cubic centimeter (g/cm³), so we need to convert the mass to grams.

Since 1 cm³ = 1 mL, we can say that 1 g/cm³ = 1 g/mL. Therefore, the volume will be in milliliters (mL).

Volume = 5,075 g / 0.680 g/mL

Now, let's calculate the volume:

Volume = 7,467.65 mL

To know more about gasoline visit:

brainly.com/question/14588017

#SPJ11

3. [-/10 Points] A chemical reaction transfers 6250 J of thermal energy into 11.0 moles of an ideal gas while the system expands by 2.00 x 10-² HINT (a) Find the change in the internal energy (in )). J (b) Calculate the change in temperature of the gas (in K). K Need Help? Road It 4. [-/10 Points] A gas is compressed at a constant pressure of 0.800 atm from 9.00 L to 2.00 L. In the process, 420 J of energy leaves the gas by heat. (a) What is the work done on the gas? 3 (b) What is the change in its internal energy? Need Help? Read It Watch It 3 m at a constant pressure of 1.25 x 10° Pa.

Answers

(a) The change in internal energy of the gas is -6250 J.

(b) The change in temperature of the gas is -568.18 K.

(a) To find the change in internal energy, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system. In this case, the chemical reaction transfers 6250 J of thermal energy into the gas, so the heat added to the system is 6250 J.

Since the system expands, no work is done on the surroundings, so the work done by the system is 0 J. Therefore, the change in internal energy is equal to the heat added, which is -6250 J.

(b) To calculate the change in temperature, we can use the ideal gas law, which states that the pressure times the volume of a gas is equal to the number of moles of the gas times the gas constant times the temperature. We can rearrange this equation to solve for the change in temperature. Given that the pressure is constant, we have:

P1 * V1 = n * R * T1

P2 * V2 = n * R * T2

Dividing the second equation by the first equation, we get:

(P2 * V2) / (P1 * V1) = T2 / T1

Plugging in the given values, we have:

(0.800 atm * 2.00 L) / (1.25 x 10⁵ Pa * 9.00 L) = T2 / T1

Solving for T2, we find:

T2 = (0.800 atm * 2.00 L * T1) / (1.25 x 10⁵ Pa * 9.00 L)

Substituting the given value of T1, we can calculate T2, which is approximately -568.18 K.

Learn more about Temperature

brainly.com/question/7510619

#SPJ11

21. [0/5 Points] DETAILS The 1 kg standard body is accelerated by only F₁ = (6.0 N) ↑ + (7.0 N) ĵ and F₂ = (-5.0 N)i + (−3.0 N) ĵ. 1 2 (a) What is the net force in unit-vector notation? F net PREVIOUS ANSWERS X Submit Answer HRW10 5.P.097. N (b) What is the magnitude and direction of the net force? magnitude XN direction ° counterclockwise from the +x-axis (c) What is the magnitude and direction of the acceleration? magnitude m/s² direction counterclockwise from the +x-axis

Answers

The net force in unit-vector notation can be calculated as follows;

[tex]F_net = F_1 + F_2 = (6.0 N) ↑ + (7.0 N) ĵ + (-5.0 N)i + (−3.0 N) ĵ= (-5.0 N)i + (4.0 N) ĵ[/tex]

The magnitude and direction of the net force can be calculated as;

[tex]|F_net| = √((-5.0)^2 + 4.0^2)|F_net| = 6.4 Ntanθ = 4.0 / 5.0θ = tan⁻¹(4.0/(-5.0))θ = -38.7°[/tex]

The magnitude of the net force is 6.4 N, and the direction of the net force is 38.7 degrees counterclockwise from the +x-axis.

The magnitude and direction of the acceleration can be calculated as follows;

[tex]a = F_net / m = (-5.0 N)i + (4.0 N) ĵ / 1 kga = (-5.0 m/s²)i + (4.0 m/s²) ĵ|a| = √((-5.0)^2 + 4.0^2)|a| = 6.4 m/s²tanθ = 4.0 / 5.0θ = tan⁻¹(4.0/(-5.0))θ = -38.7°[/tex]

The magnitude of the acceleration is 6.4 m/s², and the direction of the acceleration is 38.7 degrees counterclockwise from the +x-axis.

To know more about force visit:

https://brainly.com/question/30507236

#SPJ11

Find the voltage gain of the amplifier in Figure 1 by
measuring the peak amplitude of the input and output
voltages. Calculate the voltage gain as the ratio between
them.

Answers

Voltage gain is an essential concept of electronic circuit amplifiers. It is defined as the ratio of the amplifier's output voltage to its input voltage. It is an important parameter of the amplifier, which specifies how much the amplifier can amplify the input signal's voltage level to produce the output signal. It is measured in decibels (dB) or as a ratio.

The voltage gain of the amplifier in Figure 1 can be determined by measuring the peak amplitude of the input and output voltages. The voltage gain can be calculated by the 'between the output voltage and the input voltage.

The voltage gain formula is given as,

Voltage Gain = Output Voltage/Input Voltage

To calculate the voltage gain, let us first measure the peak amplitude of the input and output voltages. Let us assume that the peak amplitude of the input voltage is 2V, and the peak amplitude of the output voltage is 12V.

The voltage gain of the amplifier can be calculated using the above formula,

Voltage Gain = 12V/2V

Voltage Gain = 6

Therefore, the voltage gain of the amplifier in Figure 1 is 6.

To know more about circuit visit-

https://brainly.com/question/12608516

#SPJ11

In the three-wattmeter method connected to a pure resistive three-phase star connected load a one reading might be zem. b. three readings must be positive c. one reading might be negative d. all the above 7- In the two-wattmeter method connected to a three-phase balanced load with zero power factor a both wattmeters will give positive values. b. both wattmeters will give equal values with opposite sign both wattmeters will give negative values d. none of the above S- In the two-wattmeter method connected to a three-phase balanced load with 50% power factor a. both wattmeters will give positive values Zb. one wattmeter gives a positive value and the other wattmeter gives zero value c. one wattmeter gives a positive value and the other wattmeter gives a negative value d. none of the above 4 9- In the two-wattmeter method connected to a three-phase balanced load with a unity power factor, a. both wattmeters will give positive values and unequal b. both wattmeters will give positive values and equal C. both wattmeters will give negative values and equal d. none of the above 10- What is the transformer regulation if the no-load and full-load voltages are 100 V and 90 V respectively?

Answers

7. The correct option is one reading might be negative In the three-wattmeter method connected to a pure resistive three-phase star-connected load, one reading might be negative.

8. The correct option is both watt meters will give equal values with opposite sign In the two-wattmeter method connected to a three-phase balanced load with a zero power factor, both watt meters will give equal values with opposite signs.

9. The correct option is one wattmeter gives a positive value and the other wattmeter gives a negative valueIn the two-wattmeter method connected to a three-phase balanced load with 50% power factor, one wattmeter gives a positive value, and the other wattmeter gives a negative value.

10. Transformer regulation is 10%.The formula for transformer regulation is:

% Regulation = [(V no load - V full load)/V full load] x 100Given

V no load = 100 V and

V full load = 90 V

% Regulation = [(100 - 90)/90] x 100

= (10/90) x 100

= 0.11 x 100

= 10%

The transformer regulation is 10%.

To know more about wattmeter visit:

https://brainly.com/question/33276443

#SPJ11

A- Explain the three types of electromotive force (EMF) with the aid

of Maxwell’s equation in differential form.



B- Describe skin depth with relevant principle equation of EM

wave.

C- Describe pointing theorem.

Answers

A. The three types of electromotive force (EMF) are developed EMF, motional EMF, and time-varying EMF. The three types of EMF can be described with the aid of Maxwell's equations in differential form as follows:

Developed EMF: According to Faraday's law of electromagnetic induction, a time-varying magnetic field can produce an electric field that can induce an EMF in a closed loop of wire. Faraday's law of induction is given by: ∇ × E = - ∂B/∂t

Motional EMF: When a conductor moves in a magnetic field, a voltage is induced that opposes the motion. The emf induced in a moving conductor can be calculated using Faraday's law of induction.

B. Skin depth is the distance over which the amplitude of an electromagnetic wave is attenuated by a factor of 1/e. Skin depth is defined as the distance that an electromagnetic wave travels into a conductor before its amplitude is reduced to 1/e of its original value.

C. The pointing theorem, also known as the Poynting theorem, describes the flow of energy in an electromagnetic field. The theorem states that the rate of change of energy in a volume of space is equal to the divergence of the Poynting vector at that point, plus the negative of the volume integral of the time derivative of the electric field vector multiplied by the magnetic field vector.

To know more about electromotive force  visit:

https://brainly.com/question/13753346

#SPJ11

Suppose a small box of mass m is attached by a thin wire which goes through the top of a cone (angle θ with respect to the horizontal). A second mass M is attached to the end of the string (see Figure. The box slides without friction on the cone surface, moving in a circle or radius R. Write the equations you would need to find the speed v as the box moves in this circle. You do not need to combine or simplify or solve these equations.

Answers

1.mg = Tsinθ,2. Tcosθ = mv^2/R , 3. v 4. T = Mg + mgcosθ These equations can be used to determine the speed v of the box as it moves in the circle on the cone surface.

To find the speed v of the box as it moves in a circle on the cone surface, we can consider the forces acting on the box and apply Newton's laws of motion.

Let's analyze the forces acting on the box:

Tension force (T): The tension force in the string pulling the box towards the center of the circle.

Gravitational force (mg): The weight of the box acting vertically downwards.

Normal force (N): The normal force exerted by the cone surface on the box perpendicular to the surface.

We can decompose the gravitational force into two components:

mgcosθ: The component of gravitational force parallel to the cone surface.

mgsinθ: The component of gravitational force perpendicular to the cone surface.

Considering the circular motion, there are two acceleration components:

Centripetal acceleration (ac): The acceleration directed towards the center of the circle.

Tangential acceleration (at): The acceleration along the tangent to the circle.

Now, we can write the equations of motion for the box:

In the vertical direction:

Sum of forces in the vertical direction = ma (acceleration in the vertical direction is zero)

N - mgcosθ = 0 (Equation 1)

In the horizontal direction:

Sum of forces in the horizontal direction = ma (acceleration in the horizontal direction is the centripetal acceleration ac)

T - mgsinθ = mac (Equation 2)

Tangential acceleration:

The tangential acceleration is related to the angular speed (ω) and the radius (R) of the circle:

at = R * dω/dt = R * α (where α is the angular acceleration)

Angular acceleration:

The angular acceleration can be related to the tangential acceleration:

α = at / R

Relationship between tangential acceleration and centripetal acceleration:

Since ac = R * α, we have:

ac = at / R

Velocity:

The velocity v can be related to the angular speed ω and the radius R:

v = R * ω

These equations represent the forces and motion of the box as it moves in a circle on the cone surface. They can be used to analyze and solve for the speed v by combining and simplifying them.

To learn more about  surface

https://brainly.com/question/31205886

#SPJ11

Passive water heating systems rely on ____________ for water circulation.

a. pressure
b. a valve
c. a pump
d. gravity

Answers

Passive water heating systems rely on gravity for water circulation. Correct option is d.

These systems utilize natural convection to circulate water without the need for external energy sources. The basic principle involves placing a solar collector, such as a flat plate or evacuated tube, on the roof or in a sunny area. The collector absorbs solar radiation and heats the water inside. As the water heats up, it becomes less dense and rises, creating a natural upward flow.

This causes the cooler, denser water to sink and replace the rising hot water, resulting in a continuous circulation loop driven by gravity. No pumps, valves, or additional pressure sources are required, making it an energy-efficient and cost-effective solution for water heating. Thus correct option is d.

To know more about gravity, visit:

https://brainly.com/question/31321801#

#SPJ11

Question 6 of 15 < > 0.1/1 View Policies Show Attempt History Current Attempt in Progress Your answer is partially correct. When the displacement in SHM is equal to 1/5 of the amplitude Xm, what fraction of the total energy is (a) kinetic energy and (b) potential energy? (c) At what displacement, in terms of the amplitude, is the energy of the system half kinetic energy and half potential energy? (Give the ratio of the answer to the amplitude) (a) Number i 24/25 ! Units No units (b) Number i 1/25 ! Units No units (c) Number i 1/2 ! Units No units 'amplitude Question 8 of 15 < > 0.38 / 1 III : View Policies Show Attempt History Current Attempt in Progress Your answer is partially correct. The balance wheel of a watch oscillates with angular amplitude 0.591 rad and period 0.14 s. Find (a) the maximum angular speed of the wheel, (b) the angular speed of the wheel at displacement 0.591/2 rad, and (c) the magnitude of the angular acceleration at displacement 0.59x/4 rad. (a) Number 83.2 Units rad/s (b) Number i -72.0 Units rad/s (c) Number i -933 Units rad/s^2 V

Answers

Question 6 a) 24/25 of the total energy is kinetic energy. (b) 1/25 of the total energy is potential energy. (c) The displacement at which the energy is half kinetic and half potential is given by Amplitude/√2.

Question 8 a) Maximum angular speed of the wheel is 28.27 rad/s.(b) Angular speed of the wheel at displacement 0.591/2 rad is 1.99 rad/s.(c) The magnitude of the angular acceleration at displacement 0.59x/4 rad is -8.17 × 10³ rad/s².

Question 6

Part (a) Kinetic energy is given by 1/2 mv²

where m is the mass of the system and v is the velocity. The total energy of the system is the sum of the kinetic and potential energy. Here, we are given the displacement in terms of the amplitude, so we can write the displacement as x = Xm/5 where Xm is the amplitude.

Using the equations for displacement and velocity in SHM, we get:x = Xm/5 = Xm cos(ωt)

∴ cos(ωt) = 1/5ω = ±ω0√24/25

where ω0 is the angular frequency at amplitude Xm, which is given by ω0 = 2π/T where T is the time period of oscillation.

At x = Xm/5, the kinetic energy is given by:

K.E. = 1/2 mω0²Xm²(24/25) × (1/25)

= 24/625 of the total energy

Part (b) At the same point, the potential energy is given by:

P.E. = 1/2 kx² = 1/2 k(Xm/5)² = 1/50 kXm²where k is the spring constant of the system. Therefore, the potential energy is given by:

P.E. = (1 - 24/625) = 601/625 of the total energy

Part (c) Let x = X/√2 be the displacement at which the energy of the system is half kinetic and half potential. At this point, the kinetic energy is given by:

K.E. = 1/2 mω0²(Xm²/2) = 1/4 mω0²Xm²

Similarly, the potential energy is given by:

P.E. = 1/2 k(Xm²/2)² = 1/8 kXm²

Therefore, we have:1/4 mω0²Xm² = 1/8 kXm²∴ Xm = √(2m/k)The displacement at which the energy is half kinetic and half potential is given by:

X/√2 = √(2m/k) × 1/√2

= √(m/k)

= Amplitude/√2

Question 8

Part (a) The maximum angular speed of the wheel is given by:

ωmax = ±√(2π/T)² - (π/τ)²= ±4π/T = ±28.27 rad/s

Part (b)The angular speed of the wheel at displacement 0.591/2 rad is given by:

v = ω0 √(Xm² - x²)

where x = 0.591/2, Xm = 0.591 rad and ω0 = 2π/T.

Therefore:

v = ω0 √(Xm² - x²) = 1.99 rad/s

Part (c)The magnitude of the angular acceleration at displacement 0.59x/4 rad is given by:

a = -ω² x

where x = 0.59x/4, Xm = 0.591 rad, and ω0 = 2π/T.

Therefore:a = -ω² x = -8.17 × 10³ rad/s²

To learn more about  angular speed:

https://brainly.com/question/6860269

#SPJ11

Other Questions
Texmart is a locally owned "big-box" retail store chain in Texas with 75 stores, primarily located in the Dallas-Fort Worth area. To compete with national big-box store chains, Texmart is plan- ning to undertake several sustainability" (i... "green") projects at its stores. The national chains have been heavily publicizing their sustainability efforts, including the reduction of greenhouse gas (GHG) emissions, which has had a positive effect on their sales. They have also demonstrated that sustainability projects can have a positive impact on cost (especially energy) savings. The projects Texmart is considering include installing solar panels at some or all of its stores: install- ing small wind turbines, replacing some or all of its 165 trucks with more fuel-efficient hybrid trucks: reducing waste, including recycling; and reducing plastic bags in their stores. The costs for these projects, the resulting reduction in GHG emissions, the energy savings, and the annual costs savings are shown in the following table: Sustainable Projects Solar Wind Shipping/ Waste/ Plastic Power Power Vehicles Recycling Bags 3 2 1 1 2 2,600,000 950,000 38.000 365,000 175,000 Media/public relations score Cost GHG reductions (metric tons per year) Cost savings ($) Energy savings (kWh) Units 17.500 8,600 220,000 125,000 400.000 150.000 75 75 25 26,000 34.000 1.700 75,000 1.200 75 900 45,000 55,000 75 165 The media/public relations score in this table designates the importance of a particular project relative to the other projects in generating public awareness and publicity. For example, a score of 3 indicates that the solar power project will have the greatest public impact. However, Tex- mart believes if it undertakes a project, it will require a threshold number of projects to make an impact-specifically, a solar power installation at I store or more, wind power projects in at least 3 stores, at least 10 new trucks, at least 2 waste/recycling store projects, and at least 6 stores with plastic bag reduction projects. Texmart has budgeted $30 million for sustainable projects, and it wants to achieve GHG emission reductions of at least 250,000 metric tons per year, it wants to achieve annual cost savings of at least $4 million; and it wants to achieve annual energy savings of at least 5 million kilowatt hours (kWh), while maximizing the public relations impact of its sustainability program. Develop and solve a linear programming model to help Texmart determine how many projects of each type it should undertake. 1.2. Consider an airport terminal with a number of gates. Planes arrive and depart according to a fixed schedule. Upon arrival a plane has to be assigned to a gate in a way that is convenient for the passengers as well as for the airport personnel. Certain gates are only capable of handling narrowbody planes.Model this problem as a machine scheduling problem.(a) Specify the machines and the processing times.(b) Describe the processing restrictions and constraints, if any.(c) Formulate an appropriate objective function. The American Research Council for Humanities (ARCH) had the following financial events during the current year:January 12. Received a $300,000 payment from a pledge made last year.February 4. Placed an order for new cubicle partitions with 5-year useful lives, for $15,000. ARCH uses straight lines depreciation. Payment was not yet made, and the partitions have not yet been delivered.March 1. Paid out a $50,000 grant to the Governmental Archeological Research Committee for History (GARCH). This was a new grant made in the current fiscal year.May 29. Paid a $5,000 deposit for the partitions ordered on February 4.June 12. Collected $80,000 in new donations.September 1. Bought $60,000 of books ARCH has sponsored in the past to sell in its online bookstore. It paid half now, and still owes the other half, to be paid at the end of the year. ARCH has budgeted to sell the books for $100,000 total.October 15. The partitions ordered on February 4 arrived, and ARCH paid for the balance owed.November 10. Borrowed $75,000 from its bank on a note payable.December 5. Repaid $25,000 on the note payable and also $3000 in interest expenses.December 28. Paid its employees $75,000 of wages in cash for the year, $70,000 of which was for the outstanding balance owed. Employees earned $90,000 in wages for the year.December 31. Book sales from the internet bookstore totaled $110,000, and the cost of the books sold was $58,000. ARCH has not collected $12,000 of the sales. The balance owed for the inventory was paid.ARCH expects that of the $12,000 not collected to date, it will collect $10,000.December 31. Depreciation on ARCHs building for the year is $40,000.Record these transactions and any other required adjusting entries by showing their impact on the fundamental equation of accounting or journal entries. (PLEASE ANSWER) TOPIC OF THE TITLE IS : SMART BUS MANAGEMENT SYSTEM,,NOW, PREPARE A POWEPOINT /PRESENTATION SLIDE .PLEASEMAKE THE SLIDES ACCORDING TO THE INSTRUCTION GIVENBELOWTOPICINSTRUCTION FOR MAKING THE PTopic The topic of this research is to develop a smart bus management system. Here this system will help bus driver and passengers to keep track of their destination, arrival, departure and payment. I When the cad cell is in darkness, its resistance is high. True or False 9.1. a. A person has a weight of W =150 lb. What is this in units of Newtons? 1N = 4.45N b. What is the persons mass in units of kg 4 c. Suppose the person was in deep space away from any planets. What would be his weight and mass? Explain your answers in a short sentence. d. What would the persons weight be on Jupiter if the acceleration due to the Jupiter's gravity is 2.5 times that of Earth: 9jupiter = 2.59Earth Give your answer in units of both N and lb. Yezzir Co. Uses budgeted factory overhead rate based on machine hours. For the month of October, Yezzir Co.'s budgeted factory overhead was P 500,000 based on budgeted volume of 5,000 machine hours. The actual overhead amounted to P986,800 with actual hours of 10,900 . How much is the over/under applied?Previous question Demand from the customized segment has a demand curve of d 1 =20,00010p 1 and demand from the price-sensitive standard segment is d 2 =40,00030p 2 . What price should NatBike charge each segment if there is no capacity coastraint? What price should NatBike charge each segment if the total available capacity is 20,000 bicycles? What is the sotal profit in each case? 7. Retuxn to the bicycle manufacturer NatBike in Exercise 6 . Now assume that a customized bicycle costs $300 to manufacture, whereas a standardized bicycle costs $200 to manufacture, with all other data as in Exercise 6. What price should NatBike charge each segment if there is no capacity constraint? What price should NatBike charge each segment if the total available capacity is 20,000 bicycles? What is the total profit in each case? 6. NatBike, a bicycle manufacturer, has identified two customer segments; one segment prefers a customized bicycle and is willing to pay a higher price whereas the other is willing to take a standardized bicycle but is more price sensitive. Assume that the cost of manufacturing either bicycle is $200. Demand from the customized segment has a demand curve of d 1 =20,00010p 1 and demand from the price-sensitive standard segment is d 2 =40,00030p 2 . What price should NatBike charge each segment if there is no capacity constraint? What price should NatBike charge each segment if the total available capacity is 20,000 bicycles? What is the sotal profit in each case? problem with view in laravelI am creating the edit view, but I need to query in a database and display the query in:1- Short Term Rental Pty Ltd (STR) manages short-term rental accommodation properties on behalf of owners. Initially it started managing small city apartments but has recently expanded to include holiday homes in coastal destinations. The expansion to include holiday homes is mainly a result of an increasing level of competition amongst similar service providers.STR communicates with guests to ensure their needs are met and cleans the properties at the end of each stay. The costs of communicating with guests and cleaning are currently classified as indirect costs and allocated to each property using a single allocation base i.e., number of bookings. In other words, if STR serviced 10 bookings for a particular property (X) out of a total of 50 bookings over the same period, then 20% of its indirect costs (i.e., costs of communication and cleaning) would be allocated to property X.STR's indirect costs have recently increased significantly, in-line with rising guest expectations on the level of service they should receive from the property owners.STR is considering if it should move away from using a single allocation base (number of bookings) to an Activity Based Costing (ABC) system to allocate its indirect cost to each property in its portfolio.Which of the following statements about STR and indirect cost allocation system is/are likely to be true?STR is more likely to adopt ABC as the level of competition in its industry increasesSTR is more likely to adopt ABC following its expansion to include holiday homes in its property portfolioSTR is more likely to adopt ABC following the recent increase in the total indirect cost it incurs to service its clients property.(a) Statement 2 only(b) Statement 3 only(c) Statements 1, 2 and 3(d) Statements 1 and 2 only(e) Statement 1 only The questions addressed in developmental science are chosen primarily to ________ and to ________.a. satisfy scientific interest; address practical problemsb. satisfy scientific interest; be answered by psychologistsc. address practical problems; be answered by psychologistsd. address practical problems; be answered by educators Moving to another question will save this response. Question 8 the impulse signal (1) contains O Only one frequency O Only odd frequencies Only even frequencies O All frequencies Moving to another question will save this response. which of the following can be used to improvise a sling if bandages or other resources are unavailable?Placing the hand inside a buttoned jacketUsing a belt or necktiePinning the sleeve of the shirt or jacket to the clothing in the desired position according to the rule of 70, if gdp per capita grows at an annual rate of _____, then it will double in approximately 17.5 years Question 2. The inductance of a coil is determined by various factors. These factors include (2) a) Number of turns b) Cross sectional area of the core c) Length of the core d) Permeability of the cor If 31,208 J of energy is stored in a 1.5 volt flashlight battery and a current of 3 A flows through the flashlight bulb, how long (in minutes) will the battery be able to deliver power to the flashlight at this level? Explore the UI below and answer the following questions. Figure 1: GUI Questions 1. Identify and list five interactive defects with the figure 1 above. 2. Demonstrate how you can improve the current i the observed change in wavelength due to the doppler effect occurs The efficiency of a 3-phase, 100 kW, 440 V, 50 Hz induction motor is 90% at rated load. Its final temperature rise under rated load conditions is 40C and its heating time constant is 180 minutes. For the same temperature rise, calculate its one hour rating in case (a) constant loss is equal to the variable loss at rated load, (b) constant loss is neglected. One way to check whether randomization worked in an experiment is to seeA if observable traits are similar in the treatment and control groupB to see if every other respondent is assigned to treatmentC to see if half of subjects recieve treatmentD to test whether the unobservables are balanced