the heat flow rate to the inside of the glass box is 190 watts (W)..
To calculate the heat flow rate to the inside of the glass box, we can use the formula for heat transfer through a material:
Q = k * A * ΔT / d,
where:
Q is the heat flow rate,
k is the thermal conductivity of the material,
A is the area through which heat is transferred,
ΔT is the temperature difference across the material, and
d is the thickness of the material.
In this case, we are given:
A = 0.95 [tex]m^2[/tex] (area of the glass box)
ΔT = (30 °C - 10 °C) = 20 °C (temperature difference)
d = 0.010 meters (thickness of the glass box)
We need to determine the thermal conductivity, k, of the glass material. The thermal conductivity depends on the specific type of glass being used. Let's assume a typical value for ordinary glass, which is around 1 W/(m*K) (Watt per meter per Kelvin).
Substituting the values into the formula, we get:
Q = (1 W/(m*K)) * (0.95 [tex]m^2[/tex]) * (20 °C) / (0.010 m)
= 190 W
to know more about heat visit:
brainly.com/question/13860901
#SPJ11
All parts of this problem pertain to the given circuit, here showing three node voltages laheled \( v_{1}, v_{2} \) and \( v_{2} \) - (a) (4 points) Fxpresk voltage ro and current \( I \) e in terms o
The given circuit is shown below:Given circuitThe current, I, is given as follows:
[tex]$$I = \frac{V_{1} - V_{2}}{3 \Omega}$$Using KCL at node B:$$\frac{V_{1} - V_{B}}{2 \Omega} + \frac{V_{1} - V_{2}}{3 \Omega}[/tex]
[tex]= 0$$$$\frac{V_{1} - V_{B}}{2} + \frac{V_{1} - V_{2}}{3}[/tex]
[tex]= 0$$$$\frac{3V_{1} - 3V_{B} + 2V_{1} - 2V_{2}}{6}[/tex]
[tex]= 0$$$$5V_{1} - 5V_{B} + 3V_{1} - 3V_{2}[/tex]
[tex]= 0$$[/tex]Rearranging the above equation:
[tex]$$5V_{1} - 5V_{B} = 3V_{2} - 3V_{1}$$$$10V_{1} - 10V_{B}[/tex]
[tex]= 6V_{2} - 6V_{1}$$$$16V_{1} - 10V_{B} - 6V_{2}[/tex]
[tex]= 0$$Using KCL at node C:$$\frac{V_{B} - V_{C}}{4 \Omega} - \frac{V_{C}}{5 \Omega}[/tex]
[tex]= 0$$$$\frac{V_{B} - V_{C}}{4} - \frac{V_{C}}{5}[/tex]
[tex]= 0$$$$5V_{B} - 5V_{C} - 4V_{C}[/tex]
[tex]= 0$$$$5V_{B}[/tex]
[tex]= 9V_{C}$$Substituting the above equation in (2):$$16V_{1} - 10 \cdot \frac{9}{5}V_{B} - 6V_{2}[/tex]
[tex]= 0$$$$16V_{1} - 18V_{B} - 6V_{2} = 0$$$$8V_{1} - 9V_{B} - 3V_{2}[/tex]
[tex]= 0$$[/tex]We know that the voltage across the 5 Ω resistor is given by:
[tex]$$V_{C} = -4I$$$$V_{C}[/tex]
[tex]= -4\frac{V_{1} - V_{2}}{3}$$Substituting in (3):$$8V_{1} - 9V_{B} - 3V_{2}[/tex]
[tex]= 0$$$$8V_{1} - 9V_{B} - 3\cdot-4\frac{V_{1} - V_{C}}{3} = 0$$$$8V_{1} - 9V_{B} + 4V_{1} - 4V_{C} = 0$$$$12V_{1} - 9V_{B} - 4V_{C} = 0$$$$4V_{C}[/tex]
[tex]= 3V_{B} - 4V_{1}$$$$4\left(-4\frac{V_{1} - V_{2}}{3}\right) = 3V_{B} - 4V_{1}$$$$-\frac{16}{3}V_{1} + \frac{16}{3}V_{2} = 3V_{B} - 4V_{1}$$$$-\frac{4}{3}V_{1} + \frac{16}{3}V_{2} = 3V_{B}$$$$-4V_{1} + 16V_{2}[/tex]
[tex]= 9V_{B}$$[/tex]We have obtained three equations from KCL at node B, KCL at node C and the voltage across the 5 Ω resistor. We can solve these equations simultaneously to obtain the unknown node voltages.'
To know more about circuit visit:
https://brainly.com/question/12608516
#SPJ11
1. When the phase emf waveform of an ac machine is improved by using distributed or short-pitch windings, is the emf waveform of each conductor in the coils also improved? 2. How should we connect the coil groups corresponding to different poles in series for 3-phase double-layer windings? And explain the reason.
1. Yes, when the phase emf waveform of an ac machine is improved by using distributed or short-pitch windings, the emf waveform of each conductor in the coils is also improved.
2. And explain the reason. In order to connect the coil groups corresponding to different poles in series for 3-phase double-layer windings, we need to consider the following things: Series connection of the coil groups can be done in two ways: one is simplex and the other is multiplex.
In the simplex lap winding, two groups of coils (one group for each phase) are connected in series per pole. As a result, the number of paths is equal to the number of poles.In the multiplex lap winding, the coils are connected in series to form multiple paths. A multiplex lap winding with q paths has q/2 coil groups per phase.
The reason for connecting the coil groups corresponding to different poles in series for 3-phase double-layer windings is to generate a rotating magnetic field. The rotating magnetic field is created because each phase of the winding is offset by 120 electrical degrees with respect to each other. This causes the magnetic field produced by one phase to interact with the other two phases, creating a rotating magnetic field.
To learn more about waveform visit;
https://brainly.com/question/31528930
#SPJ11
A 500 N cube of density rho = 1800 kg/m3 falls through water at a
constant speed
U. Determine U if the cube falls with an orientation to minimize
the drag force. Hint: don’t
forget buoyancy.
Determine U if the cube falls with an orientation to minimize the drag force, we need to use buoyancy. The formula for the buoyant force is given by Fb = ρVg.
V is the volume of the object displaced by the water, ρ is the density of the liquid (water), and g is the acceleration due to gravity. We can use this formula to find the weight of the cube in water.
Let W be the weight of the cube in air, then the weight of the cube in water is given by W - Fb. The buoyant force Fb is given by
Fb = ρVg
= (1800 kg/m³)(0.125 m³)(9.81 m/s²)
= 2212.5 N.
The weight of the cube in air is given by
W = mg
= (500 N)/(9.81 m/s²)
= 50.91 kg.
The weight of the cube in water is given by W - Fb = 50.91 kg - 2212.5 N = -2161.59 N.
We can set these two forces equal to each other and solve for U:
FD = W - Fb(1/2)ρCU²A
= W - FbU
= sqrt((2(W - Fb))/(ρCA))
Plugging in the values, we get
U = sqrt((2((50.91 kg)(9.81 m/s²) - 2212.5 N))/(1000 kg/m³)(0.25 m²)(0.8))
≈ 1.44 m/s.
The cube falls at a constant speed of 1.44 m/s when oriented to minimize the drag force.
To know more about density visit:
https://brainly.com/question/29775886
#SPJ11
Draw the voltage-amplifier model and label its elements.
The voltage amplifier model is the representation of a device that increases the voltage level of an input signal. It is a basic building block of electronic circuits, commonly used in audio and radio frequency amplification circuits.
The model comprises of three elements: input resistance (Rin), output resistance (Rout) and voltage gain (Av). Rin represents the resistance between the input signal source and the amplifier input, Rout is the resistance between the amplifier output and the output load, and Av is the voltage gain of the amplifier.
The figure below shows a basic voltage amplifier model: Voltage Amplifier Model The input signal is applied to the input resistance, Rin. The output signal is taken across the output resistance, Rout. The voltage gain of the amplifier is given by Av = Vout / Vin, where Vout is the output voltage and Vin is the input voltage.
To know more about amplifier visit:
https://brainly.com/question/33224744
#SPJ11
Consider the motion of an object modeled with ideal projectile motion (neglecting air resistance). The trajectory of the object can be derived from basic physics and is given by the formula: \( y=x \t
The formula for the trajectory of an object modeled with ideal projectile motion is y = xtanθ – (gx²) / 2v²cos²θ.
Projectile motion is a type of motion experienced by objects that are launched into the air and are subject to gravity and air resistance. In ideal projectile motion, the air resistance is neglected, and only the force of gravity is considered. The trajectory of the object is given by the formula:
y = xtanθ – (gx²) / 2v²cos²θ where y is the height of the object, x is the horizontal distance traveled by the object, θ is the angle of projection, v is the initial velocity of the object, and g is the acceleration due to gravity. When the object is launched at an angle of 45 degrees, the horizontal distance traveled by the object is equal to the vertical distance traveled by the object. Therefore, the maximum range of the projectile is achieved at an angle of 45 degrees.
Learn more about projectile motion here:
https://brainly.com/question/12860905
#SPJ11
If the amplitude of an oscillating pendulum decreases to 72.4%
of its initial value in 2.41 seconds, then at what percentage will
the amplitude decrease in 6.65 seconds?
The percentage by which the amplitude will decrease in 6.65 seconds is 100% - 36.6% = 63.4%.
Given that the amplitude of an oscillating pendulum decreases to 72.4% of its initial value in 2.41 seconds.
We need to find out at what percentage will the amplitude decrease in 6.65 seconds.
To solve the above problem, we will use the formula for the amplitude of an oscillating pendulum.
This formula is given as:A = A0e^(-γt)
Here, A0 is the amplitude of the oscillation at t = 0.γ is the damping constant.t is the time elapsed.
A is the amplitude of the oscillation after time t has elapsed.
Now, we are given that the amplitude of an oscillating pendulum decreases to 72.4% of its initial value in 2.41 seconds. We can use this information to write an equation as:0.724A0 = A0e^(-γ × 2.41)
Let's simplify the above equation by dividing both sides by A0.e^(-γ × 2.41) = 0.724
Taking the natural logarithm of both sides, we get:-γ × 2.41 = ln 0.724γ = -ln 0.724 / 2.41γ = 0.3240...
Now we can use the value of γ to find the amplitude after 6.65 seconds.
A = A0e^(-γt)A = A0e^(-0.3240... × 6.65)
A = 0.366A0
So the amplitude decreases to 36.6% of its initial value.
Therefore, the percentage by which the amplitude will decrease in 6.65 seconds is 100% - 36.6% = 63.4%.
Hence, the DETAIL ANS is that the amplitude will decrease by 63.4% in 6.65 seconds.
Learn more about oscillating pendulum
brainly.com/question/3349259
#SPJ11
can someone help me design a tuned c clsss amplifier
with an output of 3 watts and an efficiency of 99% driven at 100kHz
frequency
Here's a general guideline to get started include Determining the load impedance, Choosing an appropriate transistor, Designing the tank circuit, Biasing, and matching the network, etc.
The design of a tuned Class C amplifier with an output of 3 watts and an efficiency of 99% at a frequency of 100 kHz. Here's a general guideline to get started:
Determine the load impedance: Begin by determining the load impedance (Zload) that the amplifier will drive. This will depend on the specific application and requirements.
Choose an appropriate transistor: Select a transistor that is suitable for high-frequency operation and can handle the desired power output. Consider factors such as power handling capability, frequency range, and gain characteristics.
Design the tank circuit: The tank circuit consists of the inductor and capacitor connected in parallel. Calculate the values of the inductor (L) and capacitor (C) based on the desired resonant frequency (100 kHz) and the load impedance. The resonant frequency can be calculated using the formula f = 1 / (2 * π * √(L * C)).
Biasing and matching network: Design the biasing and matching network to provide appropriate DC biasing to the transistor and impedance matching between the input and output stages. This will help optimize power transfer and efficiency.
Power supply considerations: Ensure that the power supply used for the amplifier can provide sufficient voltage and current to meet the desired output power and efficiency. Consider factors such as voltage regulation, filtering, and stability.
Perform simulations and adjustments: Utilize circuit simulation software to simulate and optimize the amplifier's performance. Adjust component values as necessary to achieve the desired output power and efficiency.
It's important to note that designing a tuned Class C amplifier requires a good understanding of RF circuit design principles and considerations. It's recommended to consult specialized literature or seek guidance from experienced RF engineers to ensure a successful design.
To learn more about load impedance click here
https://brainly.com/question/31789748
#SPJ11
13. 5. You are watching a bat fly out from the bottom of a well. The bat flies in a helical path so that its position vector is given by
r
=5cos(
3
2π
t)
^
+5sin(
3
2π
t)
^
+4t
k
^
. The origin x=0,y=0,z=0 is fixed at the center of the well, and the z-axis is directed upward from the bottom of the well. Note that t=0 when the bat is at the bottom of the well. The well is of depth 20 m. How long does it take before the bat exits the well? Please give your answer in s. 3.12
It takes 5 seconds for the bat to come out of the well.
Given the position vector of a bat as r = 5cos(3/2πt)i + 5sin(3/2πt)j + 4tk, we have to calculate the time taken by the bat to come out of the well. The depth of the well is given to be 20 m. So, let's start with the solution.
The position vector of the bat is given by r = 5cos(3/2πt)i + 5sin(3/2πt)j + 4tk.
In this equation, the position vector of the bat r is the sum of three vectors: r = r_1 + r_2 + r_3, where r_1 = 5cos(3/2πt)i, r_2 = 5sin(3/2πt)j and r_3 = 4tk.
The bat is coming out of the well so we have to calculate the time it takes for the bat to come out of the well. For this, we will set the value of z equal to 20.
The position vector of the bat at the mouth of the well is: r = 5cos(3/2πt)i + 5sin(3/2πt)j + 20k
We need to solve this equation for t, which will give us the time taken by the bat to come out of the well.
Equating z-coordinate to 20: 20 = 4t⇒ t = 5 seconds
Therefore, it takes 5 seconds for the bat to come out of the well.
Therefore, the correct option is (d) 5 seconds.
To know more about vector refer to:
https://brainly.com/question/30817683
#SPJ11
Q1. (a) An Amplitude Modulation (AM) modulator has output VAM(t)=40cos2π(200)t+4cos2π(180)t+4cos2π(220)t i) Illustrate the AM signal as seen from an oscilloscope. Label clearly the amplitude and length (period, T ) of the AM waveform. ii) Determine the modulation index, m. iii) Calculate the power for carrier and sideband components. iv) Determine the power efficiency of this AM signal. v) Suggest TWO (2) ways to improve the power efficiency of the AM modulator. (b) Illustrate the block diagram of an envelope detector circuit at the receiver if the negative cycle of the full-AM signal is required.
a) Modulation index, m can be determined as follows:| m | = (Vmax−Vmin)/(Vmax+Vmin)4; Total power (PT) of the AM signal is 204 mW6 ; power efficiency of the AM signal is 1.96%7.
(a) The illustration of AM signal as seen from an oscilloscope : amplitude modulation AM waveform
1. The amplitude of the carrier signal (Vc)= 40 V
2. The modulation frequency (fm) = 10 Hz
The modulation index, m can be determined as follows:| m | = (Vmax−Vmin)/(Vmax+Vmin)4.
3.The power for carrier and sideband components can be determined as follows: Pc = (Vc/√2)2 / RL
= 200 mW
PSB= (VSB/√2)2 / RL
= 4 mW
The total power (PT) of the AM signal is given by: PT = Pc + PSB
= 204 mW.
4. The power efficiency of the AM signal is given by:η= PSB/PT*100%
= 1.96%7.
5. Two ways to improve the power efficiency of the AM modulator are:• Using a smaller value of modulation index m.
• Using a more efficient modulator such as a phase modulator or a frequency modulator.
(b) The function of each block in the envelope detector circuit is as follows:• The series combination of a capacitor C and a diode D serves as a rectifier circuit that allows only the positive half cycles of the modulated signal to pass through.
• The output of the rectifier circuit is connected to a filter network which is an RL series circuit.• The filter network smoothens the output by reducing the ripples and provides a relatively constant voltage.• The output of the filter network is then the recovered modulating signal.
To know more about Modulation index, refer
https://brainly.com/question/33279380
#SPJ11
Solve the formula for one variable.
Solve for F: C=5/9(F-32); If C= 25°C
Solve for E IF P=; IF M=4KG AND P =100KGM/S
Solve for L IF T=2 AND IF G=9.8 M/S^2 AND T=2 S
Solve for K: IF T=2PI AND IF M=3.0KG AND T +9.0S
Solve for y2: 1/2MV2/1+MGY1=1/2MV2/2+MGY2
(PLEASE ANWSER THEM ALL, THANK YOU SO MUCH)
The formula for one variable F is 77°C, E = 25 kg/ms², L = 19.6 m,
The solution for each of the given problems is shown below:
Solve for F: C = 5/9(F-32); If C= 25°C
We have C = 5/9(F-32); If C= 25°C
Now, we can substitute C with the given value of 25°C.
therefore: 25 = 5/9(F - 32)
Now, we can solve for F.
Therefore: F - 32 = (9/5) × 25F - 32 = 45F = 45 + 32F = 77°C.
So, the answer is F = 77°C.
Solve for E IF P=; IF M=4KG AND P =100KG/MS
The formula is given as P = M × E
Therefore: E = P/M
Substituting the values: E = 100/4E = 25 kg/ms²
So, the answer is E = 25 kg/ms².
Solve for L IF T=2 AND IF G=9.8 M/S² AND T=2S
The formula is given as L = 1/2GT²
Substituting the values: L = 1/2(9.8)(2²)L = 1/2(9.8)(4)L = 19.6 m
So, the answer is L = 19.6 m.
Solve for K:
IF T=2PI AND IF
M=3.0KG AND T +9.0S
The formula is given as K = 2π/T × (Mg + F)
Given, T = 2π, M = 3 kg, and T + 9 s
We have to find F.
Substituting the given values:
T = 2π = 6.28 s
M = 3 kg
F = K × T/(2π) - MgF = K × 6.28/(2π) - 3 × 9.8F = K × 2 - 29.4
Therefore, the answer is F = (K × 2) - 29.4
Solve for y2: 1/2MV²/1+MGY₁=1/2MV²/2+MGY₂
We have to solve for y2.
So, we need to use the given formula and isolate y2.
Therefore: 1/2MV²/1+MGY₁=1/2MV²/2+MGY₂
Multiplying both sides by
(2 + MGY₂): 1/2MV²(2 + MGY₂)/(1+MGY₁) = 1/2MV²
Dividing both sides by 1/2MV²: (2 + MGY₂)/(1+MGY₁) = 1
Now, cross-multiply to get rid of the denominators:
2 + MGY₂ = 1 + MGY₁MGY₂ - MGY₁ = 1 - 2MY₂(G - Y₁) = (1/2V²)Y₂ = (1/2V²)(G - Y₁)
Therefore, the answer is Y₂ = (1/2V²)(G - Y₁).
To learn more about one variable:
https://brainly.com/question/31340107
#SPJ11
You're working for the summer with an ornithologist who knows you've studied physics. She asks you for a noninvasive way to measure birds' masses. You propose using a bird feeder in the shape of a 47-cm- diameter disk of mass 388 g, suspended by a wire with torsional constant 5.4 N.m/rad. Two birds land on opposite sides and the feeder goes into torsional oscillation at 2.3 Hz. Assuming the birds have the same mass, calculate the mass of a single bird. Please report your mass in grams to 1 decimal place.
To find the mass of a single bird, we will use the torsional constant formula: The mass of a single bird is approximately 8.2 grams. The torsional constant formula is τ = κθ = Iαω, where:τ is torque, κ is the torsional constant,
θ is the angle of twist,
I is the moment of inertia,
α is the angular acceleration, and
ω is the angular velocity.
The formula can be written as:
κ = I (2π/T)^2.
Let's solve for the mass of the bird using the given formula:
κ = torsional constant = 5.4 N·m/rad
ω = angular velocity = 2π × f = 2 × 3.14 × 2.3 Hz = 14.44 rad/s
Diameter of feeder, d = 47 cm = 0.47 m
Mass of feeder, m = 388 g = 0.388 kg
The moment of inertia of the feeder is given by:
I = (1/2)mr²,
where r is the radius of the feeder.
r = d/2 = 0.47/2 = 0.235 m
I = (1/2)(0.388 kg)(0.235 m)²
I = 0.004 kg·m²
The mass of the bird can be calculated as:
Mass of bird = (κ/ω²I) - m
Mass of bird = ((5.4 N·m/rad)/(14.44 rad/s)²(0.004 kg·m²)) - 0.388 kg
Mass of bird = 0.0082 kg = 8.2 g
To know more about torsional visit:
https://brainly.com/question/31838400
#SPJ11
how does the addition of a nonzero cosmological constant affect the expansion of the universe?
The addition of a nonzero cosmological constant affects the expansion of the universe by introducing a repulsive gravitational force, counteracting the attractive force of matter and radiation.
The addition of a nonzero cosmological constant affects the expansion of the universe by introducing a repulsive gravitational force, counteracting the attractive force of matter and radiation. This leads to an accelerated expansion of the universe.
In the context of the Friedmann-Lemaître-Robertson-Walker (FLRW) cosmological model, which describes the large-scale structure and dynamics of the universe, the expansion rate is determined by the critical density and the components of the universe, including matter, radiation, and dark energy.
The cosmological constant, denoted by Λ (lambda), is a term in the Einstein field equations that represents a form of dark energy associated with vacuum energy. When Λ is nonzero, it contributes a constant energy density to the universe.
In the presence of a nonzero cosmological constant, the expansion of the universe accelerates over time. This means that the distances between galaxies, galaxy clusters, and other cosmic structures increase at an accelerating rate. This accelerated expansion has been observed through various cosmological measurements, including the redshift of distant galaxies and the cosmic microwave background radiation.
The inclusion of a cosmological constant provides a mechanism to explain the observed accelerated expansion and is consistent with observations of the large-scale structure of the universe.
Learn more about cosmological constant from the given link:
https://brainly.com/question/29427155
#SPJ11
6.0×10
−3
mol of gas undergoes the process shown in Part A the figure (Figure 1). What type of process is this? View Available Hint(s) Isobaric Isothermal Isochoric DO NOT CLICK THIS. This option is here so that fewer points will be taken off if you incorrectly answer the question. DO NOT CLICK THIS. This option is here so that fewer points will be taken off if you incorrectly answer the question. Figure <1 of 1 Part B If the constant volume of this process is V
c
=225 cm
3
, what is the initial temperature? Express your answer using three significant figures. If the constant volume of this process is V
c
=225 cm
3
, what is the final temperature? Express your answer using three significant figures. - Hint 1. How to approach the problem Once again, the ideal gas law can be used. In this case, recall that the number of molecules is constant, as is the volume occupied by the gas.
The main topic of the question is determining the type of process and finding the initial and final temperatures of a gas undergoing a specific process.
Based on the given information, we have 6.0×10^−3 mol of gas undergoing a process. To determine the type of process, we need to examine the conditions shown in Part A of Figure 1.
The possible types of processes mentioned are:
Isobaric: A process at constant pressure.
Isothermal: A process at constant temperature.
Isochoric: A process at constant volume.
To identify the process type, we need more information from Part A of the figure. However, since the figure is not provided, we cannot definitively determine the type of process.
Moving on to Part B, we are given that the constant volume of the process is Vc = 225 cm^3. We are asked to find the initial and final temperatures, expressed using three significant figures.
Since the process is at constant volume (isochoric), we can use the ideal gas law to solve for the temperatures. The ideal gas law states that PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature.
Since the volume (V) is constant, the equation simplifies to P = nRT/V. Since we do not have the pressure information, we cannot determine the initial or final temperature using the given information.
Therefore, without additional data or the figure mentioned in the question, we cannot provide the specific answers regarding the type of process and the initial and final temperatures.
learn more about
brainly.com/question/1189380
Gas process.
SPJ11
Briefly explain the concepts of reference direction, reference
polarity, and passive reference configuration.
Reference DirectionIn electronic circuits, current is the flow of charge. Electrons flow from the negative end of a battery to the positive end, as we've seen. However, the directions of voltage and current are not the same. The voltage in a circuit, for example, might be supplied by a battery. The positive end of the battery is at a higher voltage than the negative end, according to the battery's polarity.
The reference direction in a circuit is the direction of current flow chosen to define the polarity of the voltage and is denoted by an arrow.Reference PolarityThe reference polarity of a circuit is the direction in which the current flows. The reference polarity, unlike the reference direction, can be reversed by flipping the direction of current flow. For example, if we switch the positive and negative connections on the battery,
the reference polarity of the circuit is reversed. The voltage and current in the circuit are still present, but their polarities are reversed.Passive Reference ConfigurationA passive reference configuration is a system in which there is no net gain of energy or power, but in which an input signal causes a response. In this configuration, a sensor, such as a thermocouple, generates a voltage in response to an external stimulus, such as temperature. The voltage produced is in direct proportion to the temperature, and the sensor's output is measured with an instrument such as a voltmeter or oscilloscope.The passive reference configuration is utilized in all kinds of electronic circuits, from thermometers and thermostats to electronic filter design and control systems.
To know more about DirectionIn visit:
https://brainly.com/question/23162078
#SPJ11
Sisyphus is doomed to push a wooden crate up a ramp for all eternity. Sisyphus has a mass of 80.0 kg. If he exerts 450 N on the crate parallel to the ramp, which makes an angle of 35.0° with the horizontal, then find the total work he does in pushing it 830 m. Make sure to include the work he does on the crate and his body to get up the ramp.
If he exerts 450 N on the crate parallel to the ramp, which makes an angle of 35.0° with the horizontal, then 630,406 J is the total work he does in pushing it 830 m.
The amount of energy that is transmitted to or from an item is measured as work in physics. It is described as being the result of the force applied to an object and the length of time it is applied. Due to the fact that work is a scalar quantity, it has simply magnitude and no direction. Depending on the force's direction and the object's displacement, work might be positive or negative. In the SI system of units, joules (J) are used to represent work.
work = force x distance x cos(θ)
work{crate}= 450 N x 830 m x cos(35.0°)
work{crate} = 310,335 J
work = force x distance x sin(θ)
work{body} = (80.0 kg x 9.81 m/s^2) x (830 m x sin(35.0°))
work{body} = 320,071 J
work{total}= work_crate + work_body
work{total} = 310,335 J + 320,071 J
work{total} = 630,406 J
To know more about work, here:
https://brainly.com/question/14813637
#SPJ4
In completing one of the homeworks assigned in class an EPCC Engineering Physics student turned his phone to a streaming radio station and wade into a swimming pool. Submerging his head underwater for 10 seconds he noted that there was a difference in the sound. As the sound wave passes from air into water its wavelength does not change. its velocity does not change. its frequency does not change. all of the above Question 10 1 Point what is the decibel value of an unidentified underground sound source if it was recorded to have a sound intensity level of 1x10 W/m² 90 de B 60 dB 79 dB 96 dB 30 do An upright broom is harder to balance when the heavier end is nearest your hand. B highest, farthest from your hand. same either way. 1 Point
In completing one of the homework assigned in class, an EPCC Engineering Physics student turned his phone to a streaming radio station and waded into a swimming pool. Submerging his head underwater for 10 seconds, he noted that there was a difference in the sound.
In completing one of the homework assigned in class, an EPCC Engineering Physics student turned his phone to a streaming radio station and waded into a swimming pool. Submerging his head underwater for 10 seconds, he noted that there was a difference in the sound. The wavelength of sound is the distance between two consecutive crests of a wave, which indicates the distance traveled by the sound in one cycle. The velocity of sound changes with the medium through which it is passing; the sound wave velocity is faster in water than in air.The frequency of sound wave is the number of waves that passes a point in one second.
The frequency of sound waves remains unchanged when it passes from air to water. Sound intensity is the power of sound per unit area of a surface. It is measured in watts per square meter. The decibel (dB) scale measures sound intensity or volume. The decibel value of an unidentified underground sound source if it was recorded to have a sound intensity level of 1x10 W/m² is 90 dB. This is because the reference value for decibels (0 dB) is based on the threshold of human hearing, which is the softest sound that the human ear can detect. Sound waves of frequencies greater than 20,000 Hz are called ultrasonic, while those with frequencies less than 20 Hz are called infrasonic. The frequency of sound waves that humans can hear ranges from 20 Hz to 20,000 Hz.
When we try to balance an upright broom, it is harder to balance when the heavier end is nearest our hand, i.e., the balance point of the broom shifts closer to the heavier end. However, if the broom is upside down, it will balance in the same way as it does when it is right side up. The center of mass (COM) of an object is the point at which the mass of the object is evenly distributed. The balance of the broom is affected by the distance between the center of mass and the point of support. A higher center of mass makes an object less stable.
To know more about wavelength visit:
https://brainly.com/question/31143857
#SPJ11
"What is the magnitude of the capacitive reactance XC at a frequency of 10 kHz, if C is 10 nF?" 0.0006 ohms 0.5 ohms 35.67 ohms 1591.55 ohms
The magnitude of the capacitive reactance (XC) at a frequency of 10 kHz, with a capacitance (C) of 10 nF, is approximately 159.155 ohms.
The magnitude of the capacitive reactance (XC) can be calculated using the formula:
XC = 1 / (2 × π × f × C)
where:
f is the frequency in hertz,
C is the capacitance in farads, and
π is a mathematical constant (approximately 3.14159).
Given that the frequency is 10 kHz (10,000 Hz) and the capacitance is 10 nF (10 × 10⁻⁹ F), we can substitute these values into the formula:
XC = 1 / (2 × π × 10,000 Hz × 10 × 10⁻⁹ F)
XC = 1 / (2 × 3.14159 × 10,000 Hz × 10 × 10⁻⁹ F)
XC = 1 / (62,831.853 Hz × 10 × 10⁻⁹ F)
XC = 1 / (6.28318 × 10⁻³ Ω)
XC = 159.155 Ω
Learn more about magnitude -
brainly.com/question/30337362
#SPJ11
1.a. What is the average Velocity of nitrogen molecules in the air at temp 20°℃ ? b. What is the average Velocity of Oxugen molecules in the air at temp 20°C ? C. After n moles of gas spread at constant pressure from 1-4 lities. How much will the average velocity of gas maecules Change? do Gas in a Closed container at pressure of Batm and temp of ffc. The gas cools ontil the average relocity of the molecules is 1.2 times smaller. Ignote changes occuring in volume of container, what is the pressure in the container after cooling?
a. The average Velocity of nitrogen molecules in the air at temp 20°℃ is approximately 510 m/s.b. The average Velocity of Oxygen molecules in the air at temp 20°C is approximately 482 m/s.C.
The average velocity of gas molecules is inversely proportional to the square root of the molar mass of the gas. Hence, as the molar mass of the gas increases, the average velocity of the gas molecules decreases. Therefore, the average velocity of the gas molecules will decrease when n moles of gas are spread at constant pressure from 1-4 liters.
The average velocity of a gas molecule can be calculated using the following formula:
Average velocity = √(8RT/πM)
where R is the universal gas constant, T is the temperature in Kelvin, and M is the molar mass of the gas. The value of R is 8.314 J/mol K, and the value of π is 3.14. The molar mass of nitrogen is 28 g/mol, and the molar mass of oxygen is 32 g/mol.
a. For nitrogen at a temperature of 20°C, the average velocity is:
Average velocity = √(8 x 8.314 x 293/3.14 x 0.028)= 509.6 m/s
Therefore, the average velocity of nitrogen molecules in the air at temp 20°C is approximately 510 m/s.
b. For oxygen at a temperature of 20°C, the average velocity is:
Average velocity = √(8 x 8.314 x 293/3.14 x 0.032)= 481.9 m/s
Therefore, the average Velocity of Oxygen molecules in the air at temp 20°C is approximately 482 m/s.
C. The average velocity of the gas molecules is inversely proportional to the square root of the molar mass of the gas. Therefore, as the molar mass of the gas increases, the average velocity of the gas molecules decreases. Hence, the average velocity of the gas molecules will decrease when n moles of gas are spread at constant pressure from 1-4 liters. The pressure remains constant while the volume of the container changes. The formula that relates the initial and final volume of the gas at constant pressure is:
V1/V2 = n2/n1
where V1 and V2 are the initial and final volumes, and n1 and n2 are the initial and final number of moles of the gas.
Using this formula, we can find the final number of moles of the gas:
V1/V2 = n2/n11/4 = n2/n1n2 = n1/4
As the number of moles of gas is reduced to one-fourth, the molar mass of the gas is also reduced to one-fourth. Hence, the average velocity of the gas molecules will increase by a factor of √(4) = 2.
After cooling, the average velocity of the molecules is 1.2 times smaller than the initial velocity. This means that the final velocity is 1/1.2 times the initial velocity, or 5/6 times the initial velocity.
The pressure of the gas is inversely proportional to the volume of the gas. Therefore, as the average velocity of the gas molecules decreases, the pressure of the gas will decrease. If the average velocity of the gas molecules is reduced by a factor of 5/6, the pressure of the gas will also be reduced by a factor of 5/6. Hence, the pressure in the container after cooling is (1 atm) x (5/6) = 0.83 atm.
The average Velocity of nitrogen molecules in the air at temp 20°C is approximately 510 m/s.
The average Velocity of Oxygen molecules in the air at temp 20°C is approximately 482 m/s.
The average velocity of the gas molecules will decrease when n moles of gas are spread at constant pressure from 1-4 liters.
The pressure in the container after cooling is 0.83 atm.
To know more about average Velocity, visit:
https://brainly.com/question/28512079
#SPJ11
Excited H atoms give off radiation in the infrared region known by the balman series. It results when electrons fall from higher energy levels to n=5. Calculate the energy and the frequency of the lowest energy line in the series.
ν = ΔE / h
Now, substitute the appropriate values and calculate the result.
To calculate the energy and frequency of the lowest energy line in the Balmer series for hydrogen atoms transitioning from higher energy levels to n=5, we can use the Rydberg formula:
1/λ = [tex]R_H[/tex] * (1/n₁² - 1/n₂²)
where λ is the wavelength of the emitted light, R_H is the Rydberg constant for hydrogen (approximately 1.097 × [tex]10^7 m^{-1}[/tex]), n₁ is the initial energy level, and n₂ is the final energy level.
In this case, we have n₁ = higher energy level and n₂ = 5.
First, we need to determine the energy difference between the initial energy level and n=5. The energy difference (ΔE) can be calculated using the formula:
ΔE =[tex]E_{initial} - E_{final}[/tex]
= -13.6 eV / n₁² - (-13.6 eV / 5²)
Next, we convert the energy difference to joules:
ΔE (in joules) = ΔE (in eV) * 1.6 × [tex]10^{-19 }[/tex]J/eV
Finally, we can calculate the frequency (ν) using the equation:
ν = ΔE / h
where h is the Planck's constant (approximately 6.63 ×[tex]10^{-34 }[/tex]J·s).
Let's calculate the values:
ΔE = (-13.6 eV / n₁²) - (-13.6 eV / 5²)
= (-13.6 eV / n₁²) - (-13.6 eV / 25)
ΔE (in joules) = ΔE (in eV) * 1.6 × [tex]10^{-19}[/tex] J/eV
ν = ΔE / h
To know more about Rydberg visit:
brainly.com/question/32679031
#SPJ11
Maxwell's equations relate the electric and magnetic fields as follows:
∇x E= -∂B/∂t, ∇x H= ∂D/∂t + J, ∇. B= 0 ∇. D= rho
(i) Rewrite these equations applicable to fields in free space.
(ii) When applying these equations to fields in good conductors, what terms in these equations can be ignored?
i) According to the equations, the magnetic field's curl and the electric field's time rate of change are equal to the negative time rate of change of the magnetic field and the time rate of change of the electric field, respectively.
ii) The terms pertaining to charges and currents can be omitted when applying Maxwell's equations to fields in good conductors because they are insignificant.
Maxwell's equations are electromagnetic equations that relate the electric and magnetic fields. They are crucial in understanding many aspects of electromagnetic phenomena, including light, radio waves, and electric circuits. The equations have different forms for different types of materials.
Let us see how the equations can be rewritten for free space. Also, we will look at what terms can be ignored when applying the equations to good conductors.
i) The Maxwell's equations for fields in free space are as follows:
∇ x E = -dB/dt, ∇ x H = dD/dt, ∇ . D = 0, and ∇ . B = 0.
Here, D is the electric flux density, B is the magnetic flux density,
E is the electric field intensity, and H is the magnetic field intensity.
The equations are applicable to fields in free space because there are no charges and currents present. As a result, the electric and magnetic fields obey differential equations that do not depend on charge or current densities.
The equations state that the curl of the electric field is equal to the negative time rate of change of the magnetic field, and the curl of the magnetic field is equal to the time rate of change of the electric field.
ii) When applying these equations to fields in good conductors, the terms that can be ignored are those that relate to charges and currents. For example, the term J in the second equation (i.e., ∇ x H = dD/dt + J) can be ignored because good conductors have very high conductivity, so they have no charge accumulation and no current flows inside them. Therefore, the equation becomes ∇ x H = dD/dt.
In summary, when applying Maxwell's equations to fields in good conductors, the terms that relate to charges and currents can be ignored because they are negligible.
know more about Maxwell's equations here
https://brainly.com/question/33309675#
#SPJ11
Suppose a planet in our solar system has an orbital period of 7
years. What would be its average distance from the sun (length of
its semimajor axis)?
Suppose a planet in our solar system has an orbital period of 7 years, iits average distance from the sun (length of
its semimajor axis) would approximately 3.03 astronomical units.
If a planet has an orbital period of 7 years, the length of its semimajor axis can be determined using Kepler's third law. Kepler's third law states that the square of the orbital period is proportional to the cube of the average distance between the planet and the sun. This can be expressed as T^2 ∝ a^3, where T is the orbital period and a is the average distance from the sun. Solving for a, we get a = (T^2 * k)^(1/3), where k is a constant.
Using the value of T as 7 years, we can find the length of the semimajor axis. Plugging in the values, we get a = (7^2 * k)^(1/3).
To determine the value of k, we can use the fact that the semimajor axis of Earth's orbit is approximately 1 astronomical unit (AU).
This means that (1^2 * k)^(1/3) = 1 AU, or k = 1 AU^3. Substituting this value of k, we get a = (7^2 * 1 AU^3)^(1/3) = 3.03 AU.
Therefore, the average distance of the planet from the sun is approximately 3.03 astronomical units.
Learn more about Kepler's third law at:
https://brainly.com/question/30404084
#SPJ11
What factors influences the strength of the NMR or EPR signal?
The strength of the NMR or EPR signal is influenced by several factors. These include the magnetic field strength, as a higher field leads to a stronger signal.
The number of nuclei or paramagnetic centers contributing to the resonance also affects the signal strength.
The sensitivity and efficiency of the detector used play a role, as a more sensitive detector can detect weaker signals.
The relaxation times of the sample, T1 and T2, impact the signal strength, with longer relaxation times resulting in stronger signals.
The concentration of the sample and the molecular environment, including nearby atoms or molecules, can also influence the signal strength.
Optimizing these factors helps enhance the sensitivity and intensity of NMR and EPR signals.
Read more about NMR or EPR signals.
https://brainly.com/question/30458554
#SPJ11
A person exposed to fast neutrons receives a radiation dose of 300 rem on part of his hand, affecting 25 g of tissue. The RBE of these neutrons is 10. How many rad did he receive?
Given that a person exposed to fast neutrons receives a radiation dose of 300 rem on part of his hand, affecting 25 g of tissue and the RBE of these neutrons is 10. We need to find the number of rads he received.
RBE stands for relative biological effectiveness, which is a comparative expression of the ability of radiation to produce a biological reaction. RBE is used as a multiplying factor to calculate the equivalent dose, measured in Sieverts (Sv), that would be produced by an equal amount of absorbed dose by a type of radiation other than X-rays or gamma rays.
When dealing with other forms of ionizing radiation, the concept of RBE is essential to calculate equivalent doses. In this case, the individual was exposed to fast neutrons, which have an RBE of 10. Therefore the equivalent dose is calculated as:
Dose equivalent (rem) = Absorbed dose (rad) x Quality Factor
Since RBE is a quality factor for neutron radiation, the equivalent dose can be determined as:
E = 300 rem (dose equivalent) = 25g tissue (absorbed dose) x 10 (RBE)
Therefore, the absorbed dose in rads can be calculated by using the formula;
Dose equivalent (rem) = Absorbed dose (rad) x Quality Factor
From this formula, we can rearrange and find the absorbed dose as follows;
Absorbed dose (rad) = Dose equivalent (rem) / Quality Factor
Given that the individual received a radiation dose of 300 rem, the absorbed dose can be calculated as:
Absorbed dose (rad) = 300 rem / 10 = 30 rad
Hence, the individual received 30 rad. Therefore, the correct option is D.
Learn more about ionizing radiation: https://brainly.com/question/30541298
#SPJ11
Throttling range = 5 v DC, Kp = 2kW/ V DC
Write the equation relating heater output to sensed temperature for the controller of the answer above in the thermostat output voltage decreases linearly with temperature between 90F (32C) and 60F (16C) for the nominal thermostat set-point of 75F (24C)
Ans: Q = 1/3 (kW/F) (75 - Tsensed) + 5 kW
Q= = 1/3 kW/°C × (75°C - Tsensed) + 5 kW. The output power equation can be obtained by using the following expression: Q = Kp (Vset - Vt) Where, Q = Output power, Kp = Proportional gain, Vset = Set-point temperature in volts, Vt = Sensed temperature in volts
Thermostat output voltage decreases linearly with temperature between 90F (32C) and 60F (16C) for the nominal thermostat set-point of 75F (24C)To convert F to C, use the following expression: T(°C) = (T(°F) - 32) × 5/9, Temperature range can be converted as follows: 90°F = 32.2°C, 60°F = 15.6°C, 75°F = 23.9°C
Then, the voltage range can be calculated as follows:
V90 = 5 - (32.2 - 60) × (5/30)
= 3.14 V
V60 = 5 - (15.6 - 60) × (5/30)
= 4.16 V
For any sensed voltage, Vt = (5/30) × (Tsensed - 60) + 4.16 V
Plugging this into the output power equation and simplifying it, Q = Kp (Vset - [(5/30) × (Tsensed - 60) + 4.16 V])
Q = Kp (Vset - (5/30) × (Tsensed - 60) - 4.16 V)Q
= 2 kW/V DC × (5 V DC - (5/30) × (Tsensed - 60°C) - 4.16 V)Q
= 1/3 kW/°C × (75°C - Tsensed) + 5 kW
To know more about power equation, refer
https://brainly.com/question/31672647
#SPJ11
A large chunk of ice with mass 12.0 kg falls from a roof 5.32 m above the ground. Ignoring air resistance, what is the speed of the ice when it reaches the ground?
a. 12.5 mls
b. 12.1 mls
c. 10.8 mls
d. 7.67 m/s
we have ignored the air resistance, this is the exact velocity of the ice when it reaches the ground. Hence, the correct option is (b) 11.5 m/s.
Mass of the ice = 12.0 kg
Height of the fall, h = 5.32 m
The final velocity of the ice, v = ?
Let's use the formula for the velocity of an object falling under the influence of gravity,
v=√2gh
Here, g = acceleration due to gravity = 9.8 m/s²
We can substitute the given values in the above formula to find the velocity of the ice as:
v = √2 × 9.8 m/s² × 5.32 mv
= √(2 × 9.8 m/s² × 5.32 m)≈ 11.5 m/s
Resistance refers to the opposition that a substance or a medium offers to the flow of an electrical current. Resistance is measured in Ohms (Ω).
In physics, resistance is a measure of how much current is opposed by an object, material, or circuit component. Resistance, like its reciprocal, conductance, is a scalar quantity.
To learn more on Resistance :
https://brainly.com/question/28135236
#SPJ11
A 150 V, 1400 rpm shunt DC motor is used to supply rated output power to a constant torque load. On full-load, the line current is 19.5 A. The armature circuit has a resistance of 0.50 0, the field resistance is 150 0 with the rotational loss is 200 W. Determine: a) The developed power b) The output power c) The output torque d) The efficiency at full-load.
The developed power is 2735.125 W.
The output power is 2535.125 W.
The output torque is 232.13 N-m.
The efficiency at full-load is 92.70%.
a) Developed power
The armature current can be calculated by using Ohm’s law,i.e.,
Ia=VL−EbaRa
Here,
VL = 150 V,
Eba = Eb at full-load =
V − IaRa
= 150 − 19.5 × 0.5
= 140.25 V
Now, torque developed by the motor,
Td = (60 × Pa) / (2πN)
Where
Pa = EbIa
= 140.25 × 19.5
= 2,735.125 Watt.
N = (1400 / 60) rps
= 23.333 rps
Therefore,
Td = (60 × 2,735.125) / (2 × 3.14 × 23.333)
= 251.27 N-m.
b) Output power
The output power of the motor can be calculated using the equation,
Po = Pa − Rotational losses
= Pa − Friction and Windage losses
= 2735.125 − 200
= 2,535.125 Watt.
c) Output torque
The output torque of the motor can be calculated by using the formula,
T0 = (Po × 60) / (2πN)
= (2,535.125 × 60) / (2π × 23.333)
= 232.13 N-m.
d) Efficiency at full-load
Output power = 2,535.125 Watt
Developed power = 2,735.125 Watt
Therefore, Efficiency at full-load = (Output power / Developed power) × 100%
= (2,535.125 / 2,735.125) × 100%
= 92.70%.
Thus, the developed power is 2735.125 W.
The output power is 2535.125 W.
The output torque is 232.13 N-m.
The efficiency at full-load is 92.70%.
To know more about output torque visit:
https://brainly.com/question/31113929
#SPJ11
Ninety-nine percent of matter is made up of six elements. Which of the following is NOT one of these six?
carbon,
hydrogen,
nitrogen,
oxygen,
sulphur
phosphorus.
calcium
The element that is not one of ninety-nine percent of matter is made up of six elements is calcium (Option G).
The element calcium is not one of the six elements that make up 99% of matter. The six elements that makeup 99% of matter are carbon, hydrogen, nitrogen, oxygen, sulfur, and phosphorus. Calcium is a chemical element with the symbol Ca and atomic number 20. It is an alkaline earth metal that is a reactive pale yellow metal. Calcium is the fifth most abundant element by mass in the Earth's crust and the third most abundant (after oxygen and silicon) in the human body.
Thus, the correct option is G.
Learn more about elements: https://brainly.com/question/28450262
#SPJ11
The digital system has higher noise immunity that analog one because In the digital system identification of the symbol is more easily using threshold detection. The digital system requires higher tra
In the modern world, communication systems are playing a vital role in connecting people, organizations, and nations worldwide. In a communication system, the information transfer occurs either in an analog or digital form. Both forms have their advantages and disadvantages over each other. This article will explain why digital systems have higher noise immunity than analog ones.
The digital system has higher noise immunity than analog ones because digital signals have two states 1 and 0, which makes them less vulnerable to noise, interference, or distortion. The noise refers to any undesired or unwanted signals that mix with the original signals and make it difficult to identify or detect the information. The analog system signals are continuous and can take any value within a range, and their amplification or attenuation is directly proportional to their amplitude, which makes them highly sensitive to noise or distortion.
In the digital system, the identification of the symbol is more easily using threshold detection. The threshold detection is a process of comparing the received signals with a fixed threshold value. If the received signal amplitude is higher than the threshold value, it will be considered as 1, and if it is lower than the threshold value, it will be considered as 0. This makes the identification process more accurate and efficient, and the signal will be less susceptible to noise, distortion, or interference.
To know more about communication visit:
https://brainly.com/question/29811467
#SPJ11
What is the reaction force to the earth pulling down on a car parking on a flat driveway?
The reaction force to the Earth pulling down on a car parked on a flat driveway is the normal force exerted by the driveway on the car, which is equal in magnitude and opposite in direction to the weight of the car.
According to Newton's third law of motion, for every action, there is an equal and opposite reaction. In the case of a car parked on a flat driveway, the force exerted by the Earth on the car is the weight of the car, which acts downward. According to Newton's third law, there must be an equal and opposite reaction force.
The reaction force to the Earth pulling down on the car is the force exerted by the car on the Earth. This force is commonly referred to as the normal force. The normal force is a contact force exerted by a surface to support the weight of an object resting on it and acts perpendicular to the surface.
In the case of a car parked on a flat driveway, the normal force exerted by the driveway on the car is equal in magnitude and opposite in direction to the weight of the car. This normal force counteracts the gravitational force pulling the car downward and prevents it from sinking into the ground. It ensures that the car remains in equilibrium and does not accelerate vertically.
Learn more about reaction force here :-
https://brainly.com/question/14360695
#SPJ11
(b) How much work, w, is done to raise the one kilogram of water from the bottom of the well to the surface? C) Determine the power required by the pump if the water has a density of 1000 kg/m and the pump delivers 1000 kg/min. Note that in the Si unit system, power is measured 1/s. (d) The horsepower (hp) required by the pump.
Work = 98,000 J, Power required by the pump = 980 MW, hp = 1.31 x 10⁶
b) The work done to raise one kilogram of water from the bottom of the well to the surface is given by the product of force, distance, and gravity. It is given by the formula:
W = Fdgh where, F is the force exerted by the water, d is the distance it is lifted, and g is acceleration due to gravity.
On solving, we get W = (1000 kg/m³)(9.8 m/s²)(10 m)= 98,000 J.
c) The power required by the pump to raise 1000 kg of water per minute is given by:
W = FdghP = W/tP
= (1000 kg/min)(98,000 J/kg)P = 9.8 x 10⁸ W
= 980 MW.
d) The horsepower (hp) required by the pump is given by:
P = 9.8 x 10⁸ W/746 = 1.31 x 10⁶ hp.
Therefore, W = 98,000 J, P = 980 MW, hp = 1.31 x 10⁶.
Learn more about Power here:
https://brainly.com/question/30519200
#SPJ11
