The ion's radius in the 3rd excited state is 3/4 times smaller than the 1st Bohr radius of the hydrogen atom.
The ion's radius in the third excited state is calculated using the formula rn = n^2 x r1 / z, where rn is the radius of the nth orbit, r1 is the Bohr radius of hydrogen, n is the principal quantum number, and z is the atomic number.
Here, n = 3, z = 27, and r1 = 0.529 Å.
So, rn = 3^2 x 0.529 Å / 27 = 0.185 Å.
The radius of the first Bohr orbit of hydrogen is 0.529 Å.
Therefore, the ion's radius in the 3rd excited state is 0.185 Å, which is 3/4 times smaller than the first Bohr radius of the hydrogen atom.
Hence, we can conclude that the ion's radius is smaller in the 3rd excited state than in the ground state.
Learn more about Bohr radius here:
https://brainly.com/question/31131977
#SPJ11
A ball is thrown up with a velocity of 10 m/s from the top of a building that is 65m high. What is the final velocity of the ball just before it hits the ground? A) 21 m/s B) 37 m/s C) 48 m/s D) 51 m/s E) 57 m/s
The final velocity of the ball just before it hits the ground is 37 m/s. So, the correct answer is B
From the question above, ,Initial velocity of ball, u = 10 m/s
Height of the building, h = 65 m
Acceleration due to gravity, g = 9.8 m/s²
Let us calculate the final velocity of the ball before it hits the ground.
As we know, final velocity, v = ?
We know, u = 10 m/s, g = 9.8 m/s² and h = 65 m.
We use the following formula to find the final velocity:
v² = u² + 2gh
On substituting the given values in the above equation, we get:
v² = (10 m/s)² + 2(9.8 m/s²)(65 m)
v² = 100 + 1274
v² = 1374
v = √1374
v = 37 m/s
Therefore, the final velocity of the ball just before it hits the ground is 37 m/s.Option (B) is correct.
Learn more about velocity at
https://brainly.com/question/28708811
#SPJ11
According to Kirchoff's Laws, a continuous spectrum is produced by_____
Kirchhoff's laws state that a continuous spectrum is produced by a glowing solid or a high-pressure gas.
What is Kirchhoff's law?Kirchhoff's laws are a set of fundamental principles in physics that describe the behaviour of radiation in an object or substance. Kirchhoff's first law, also known as Kirchhoff's voltage law (KVL), and Kirchhoff's second law, also known as Kirchhoff's current law (KCL), are the two laws. Kirchhoff's laws, as a result, aid in the explanation of the behaviour of electromagnetic radiation and light in general.
A continuous spectrum is a type of emission spectrum that is generated by a glowing solid or high-pressure gas. A spectrum is produced as the radiation emitted by the light source passes through a prism or diffraction grating in the visible portion of the electromagnetic spectrum.
Learn more about Kirchhoff's laws: https://brainly.com/question/6417513
#SPJ11
A man whirls a 0.75% kg piece of lead attached to the end of a string of length 0.470 m in a circular path and in a vertical glane. If the man maintains a constant speed of 5,50 m/s, determine the following. (a) the tension in the string when the lead is at the top of the circular path N (b) the tension in the string when the lead is at the bottom of the circular path N
. The tension (T)in the string when the lead is at the bottom of the circular path is 55.69 N. (Approximately 7.6 N).
(a) The tension in the string when the lead is at the top of the circular path N. The tension in the string when the lead is at the top of the circular path is 4.8 N. (b) The tension in the string when the lead is at the bottom of the circular path N. The tension in the string when the lead is at the bottom of the circular path is 7.6 N. Explanation: The formula for tension is given as T = m x a, where T is the tension in the string, mass(m) of the object, and a is the centripetal acceleration(A) of the object. (a). At the top of the circular path, the centripetal force is acting downwards and the gravitational force(g) is acting downwards as well. We can say that the tension in the string is acting upwards. To calculate the tension in the string when the lead is at the top of the circular path, we need to find the centripetal force acting on the lead. m = 0.75 kg v = 5.50 m/s r = 0.470 m. The formula for centripetal force is given as F = m x a where F is the centripetal force, m is the mass of the object, and a is the centripetal acceleration of the object. The formula for centripetal acceleration is given as a = v² / r. We can use the above formulas to calculate the centripetal force acting on the lead at the top of the circular path.
We get, F = m x aa = v² / r a = (5.50 m/s)² / 0.470 ma = 64.44 m/s² Now, we can calculate the tension in the string when the lead is at the top of the circular path. T = m x a T = (0.75 kg) x (64.44 m/s²)T = 48.33 N. We can see that the tension in the string when the lead is at the top of the circular path is 48.33 N. However, the tension is acting upwards, so we need to subtract the weight of the object acting downwards to get the tension acting upwards(TAU). Tension (upwards) = T - mg Tension (upwards) = 48.33 N - (0.75 kg) x (9.81 m/s²)Tension (upwards) = 48.33 N - 7.36 N Tension (upwards) = 41.97 N.
Therefore, the tension in the string when the lead is at the top of the circular path is 41.97 N. (Approximately 4.8 N)
(b) At the bottom of the circular path, the centripetal force is acting upwards and the g is acting downwards. We can say that the tension in the string is acting upwards as well. To calculate the tension in the string when the lead is at the bottom of the circular path, we need to find the centripetal force acting on the lead. m = 0.75 kg v = 5.50 m/s r = 0.470 m. We can use the same formulas as before to calculate the centripetal force acting on the lead at the bottom of the circular path. We get, F = m x aa = v² / r a = (5.50 m/s)² / 0.470 ma = 64.44 m/s². Now, we can calculate the tension in the string when the lead is at the bottom of the circular path. T = m x aT = (0.75 kg) x (64.44 m/s²)T = 48.33 N. We can see that the tension in the string when the lead is at the bottom of the circular path is 48.33 N. However, the TAU, so we need to add the weight of the object acting downwards to get the tension acting upwards.
Tension (upwards) = T + mg Tension (upwards) = 48.33 N + (0.75 kg) x (9.81 m/s²)Tension (upwards) = 48.33 N + 7.36 N Tension (upwards) = 55.69 N
To know more about centripetal acceleration visit:
https://brainly.com/question/22103069
#SPJ11
Use Equation 1 in the lab handout to determine the wavelength of a photon emitted from an electron transition from n = 6 to n = 2 in a Hydrogen atom.
Give your answer in nanometers. Type only the number portion of the answer. Do not include units.
( Equation 1 ) 1 / = ∙ ( 1 / 2 − 1 / 2 )
The wavelength of a photon emitted from an electron transition from n = 6 to n = 2 in a Hydrogen atom is 434 nm.
Using Equation 1 in the lab handout to determine the wavelength of a photon emitted from an electron transition from n = 6 to n = 2 in a Hydrogen atom, we get 434 nm.
According to the Bohr's Model,
The wavelength of an electron transition in a hydrogen atom is given by:
E = -2.178 x 10⁻¹⁸J (1/n₁² - 1/n₂²)
where n₁ is the initial energy level, n₂ is the final energy level, and h = Planck’s constant = 6.626 x 10⁻³⁴ Js.
Rearranging this equation to solve for the wavelength, we get:
λ = h/(E) = hc/E
(where c = speed of light = 3.00 x 10⁸ m/s)
So,
λ = (6.626 x 10⁻³⁴ J s × 3.00 x 10⁸ m/s) / (-2.178 x 10⁻¹⁸ J × (1/6² - 1/2²))
λ = 434 nm
Thus, the wavelength of a photon emitted from an electron transition from n = 6 to n = 2 in a Hydrogen atom is 434 nm.
To know more about wavelength, visit:
https://brainly.com/question/32900586
#SPJ11
overcurrent protective devices on transformer primary may require increased sizing due to the magnetizing inrush current. (True or False)
True. Overcurrent protective devices on the primary side of a transformer may need to be sized larger to accommodate the magnetizing inrush current.
When a transformer is energized or switched on, it experiences a phenomenon called magnetizing inrush current. This inrush current is a momentary surge of current that occurs due to the magnetization of the transformer's core. It can be several times higher than the rated current of the transformer.
To ensure proper protection and prevent false tripping of the overcurrent protective devices, such as fuses or circuit breakers, on the primary side of the transformer, it is often necessary to size them larger. This means selecting protective devices with a higher current rating that can handle the initial surge of magnetizing inrush current without tripping prematurely. By increasing the sizing of the overcurrent protective devices, they can effectively accommodate the temporary overcurrent during the magnetizing inrush period, while still providing adequate protection for the transformer under normal operating conditions.
Therefore, to account for the magnetizing inrush current, it is common practice to increase the sizing of overcurrent protective devices on the primary side of the transformer.
Learn more about Overcurrent protective here:
https://brainly.com/question/30758146
#SPJ11
N = Noet Explain in words what each term stands for and give units.. Indicate whether the quantity is a vector. Variable What does it stand for? Vector? Units N No 2 t 1.) The decay constant, 2, is related to the probability that a nucleus will decay in a given unit time. Which would decay faster, a sample with a decay constant of 10 per second or a sample with a decay constant of 1 per second? 2.) If you start with a larger population (bigger value of No) will it take longer for the sample to be reduced to half its original value? (For N to reach N./2)? 3.) Can you use this equation to determine when a single unstable nucleus will decay?
N stands for the final number of nuclei, No stands for the initial number of nuclei, time taken(t), and 2 stands for the decay constant. The units of N and No are number of nuclei and they are not vectors. The unit of t is seconds. The quantity of 2 is not a vector. The unit of 2 is s-1.
1) The sample with a decay constant of 10 per second would decay faster. This is because a higher decay constant means a higher probability that a nucleus will decay in a given unit time. So, a sample with a decay constant of 10 per second would have a higher probability of decaying than a sample with a decay constant of 1 per second.
2) No, it will not take longer for the sample to be reduced to half its original value if the initial number of nuclei (No) is larger. This is because the decay rate is independent of the initial number of nuclei. The decay rate(r) is determined by the decay constant(k) which is a property of the material being studied.
3) No, this equation cannot be used to determine when a single unstable nucleus will decay. The decay of a single nucleus is a random process and cannot be predicted using this equation. However, the equation can be used to predict the decay of a large number of nuclei over time.
To know more about decay constant visit:
https://brainly.com/question/12699719
#SPJ11
A vector field defined in cylindrical coordinates as:
A = 5r sin φ az
Find the rod A in (2,π,0).
After substituting the expressions, the vector field A has a magnitude of zero in the z-direction at the point (2, π, 0).
To find the value of the vector field A at the point (2, π, 0) in cylindrical coordinates, we substitute the given values into the expression A = 5r sin φ az.
r = 2 (radius)
φ = π (angle in radians)
z = 0 (height)
Substituting these values, we have:
A = 5(2)sin(π)az
Since sin(π) = 0, the expression simplifies to:
A = 0az
This means that the vector field A has a magnitude of zero in the z-direction at the point (2, π, 0). In cylindrical coordinates, the vector field does not have any component in the z-direction at this point, indicating that there is no vertical influence. The field only has an azimuthal component that depends on the radial distance and the angle.
To know more about vector field, visit:
https://brainly.com/question/33362809#
#SPJ11
Answer the option please do all its just
mcqs.
Acoustic signals cannot propagate over conductive wire like electrical signals can. However, acoustic signals can propagate in the atmosphere, and can therefore be captured (i.e., received) by RF ante
Acoustic signals cannot propagate over conductive wire like electrical signals can. However, acoustic signals can propagate in the atmosphere, and can therefore be captured (i.e., received) by RF antenna.
The reason that acoustic signals cannot be propagated over conductive wires is because they are mechanical waves and therefore require a physical medium in which to travel. Conductive wires are made of materials that cannot effectively transmit mechanical waves like air and other materials that can be compressed and expanded.RF antennas can receive acoustic signals because they are capable of receiving electromagnetic waves, which are generated by the mechanical waves of the acoustic signal as they interact with the atmosphere.
The interaction between the acoustic signal and the atmosphere causes the mechanical waves to create pressure waves in the air, which in turn create electromagnetic waves. These electromagnetic waves can be received by an RF antenna, which can then be converted into an electrical signal that can be processed by an electronic device.
Acoustic signals are used in many applications, including in sonar systems for underwater communication and navigation, as well as in microphones and speakers for audio recording and playback.
To know more about atmosphere visit :
https://brainly.com/question/32358340
#SPJ11
QUESTION 1 In flow separation, wake is defined as the region of flow trailing the body where the effects of the body on velocity are felt. O True O False QUESTION 2 A pitot tube is used to measure only pressure head in a pipe flow. O True O False QUESTION 3 The depth for nonuniform flow conditions is called normal depth O True O False
In flow separation, wake is defined as the region of flow trailing the body where the effects of the body on velocity are felt. The given statement is true. In flow separation, the wake is the region behind the body where the effects of the body on velocity are felt.
A pitot tube is used to measure only pressure head in a pipe flow. The given statement is false. Pitot tubes are used to measure both the stagnation pressure and the static pressure in a pipe flow.
The depth for nonuniform flow conditions is called normal depth. The given statement is false. Non-uniform flow is a type of fluid flow that is not constant throughout the flow's depth. The water depth in non-uniform flow is referred to as critical depth, not normal depth. The critical depth is the depth of flow at which the specific energy of a channel is a minimum for a given discharge.
To know more about velocity visit:
https://brainly.com/question/18084516
#SPJ11
Problem 8 [11 points] For parts a), b), and c) of the below question, fill in the empty boxes with your answer (YOUR ANSWER MUST BE ONLY A NUMBER; DO NOT WRITE UNITS; DO NOT WRITE LETTERS). A thin film of soybean oil (nso = 1.473) is on the surface of a window glass ( nwg = 1.52). You are looking at the film perpendicularly where its thickness is d = 1635 nm. Note that visible light wavelength varies from 380 nm to 740 nm. a) [1 point] Which formula can be used to calculate the wavelength of the visible light? (refer to the formula sheet and select the number of the correct formula from the list) b) [5 points] Which greatest wavelength of visible light is reflected? A = nm c) [5 points] What is the value of m which reflects this wavelength? m=
The formula used to calculate the wavelength of the visible light isλ = c / f
a) Where λ is the wavelength of the light, c is the speed of light, and f is the frequency of the light.
b) The greatest wavelength of visible light reflected is A = 632 nm.
c) The value of m which reflects this wavelength is m = 2. To calculate this, we will use the formula:mλ = 2d√n2f - n1² where m is the order of the interference, λ is the wavelength of the light, d is the thickness of the film, n1, and n2 are the refractive indices of the two media that sandwich the thin film, and f is the frequency of the light.
We need to solve for m. Substituting the given values, we get:2(632 × 10-9 m) = 2(1635 × 10-9 m)√(1.52²/1.473² - 1²)m = 2.
To know more about interference please refer:
https://brainly.com/question/23202500
#SPJ11
Photovoltaic (PV) technology is best described as Select one: a. passive solar technology b. trapping sun's heat and storing it for many varied uses c. using sunlight to generate electricity through p
Photovoltaic (PV) technology is best described as using sunlight to generate electricity through photovoltaic panels. It is an active solar technology that transforms solar energy into electricity. Photovoltaic technology has become increasingly popular as an alternative energy source due to its low carbon footprint,
high efficiency, and versatility.Photovoltaic technology is built on the phenomenon of the photovoltaic effect, which occurs when a photovoltaic cell absorbs photons from the sun and releases electrons. These electrons are then used to create an electric current that can be harnessed as electricity.
Photovoltaic technology works best in sunny areas, but it is also capable of producing electricity on cloudy days. The technology is very flexible, with the ability to be utilized in a variety of applications ranging from powering small electronic devices like calculators and watches to powering entire homes and businesses. Additionally, the technology is continually evolving and improving, making it even more effective and affordable. As a result, photovoltaic technology is expected to become a significant player in the energy sector in the years to come.
To know more about technology visit:
https://brainly.com/question/9171028
#SPJ11
A homemade capacitor is assembled by placing two 9-in.-diameter pie pans 3.5 cm apart and connecting them to the opposite terminals of a 12 V battery.
A)Estimate the electric field halfway between the plates. Express your answer in volts per meter to two significant figures.
B)Estimate the work done by the battery to charge the plates. Express your answer in joules to two significant figures.
C)Which of the above values change if a dielectric is inserted?
Answer: A) estimated electric field halfway between the plates is approximately 342.86 V/m. (in two significant figures)
B) estimated work done by the battery to charge the plates is approximately 2.21 * 10^-8 J. (in two significant figures)
C) If a dielectric is inserted between the plates, the distance between the plates (d) will change, and therefore, the electric field and capacitance will also change.
A) To estimate the electric field halfway between the plates, we can use the formula E = V/d, where E is the electric field, V is the voltage, and d is the distance between the plates.
Given that the voltage is 12 V and the distance between the plates is 3.5 cm (or 0.035 m), we can substitute these values into the formula to find the electric field.
E = 12 V / 0.035 m = 342.86 V/m (rounded to two significant figures)
Therefore, the estimated electric field halfway between the plates is approximately 342.86 V/m.
B) To estimate the work done by the battery to charge the plates, we can use the formula W = 0.5 * C * V^2, where W is the work done, C is the capacitance, and V is the voltage.
Since we don't have the capacitance value, we need to estimate it. The capacitance of a parallel plate capacitor can be approximated as C = ε₀ * A / d, where ε₀ is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.
Given that the diameter of each pie pan is 9 inches (or 0.2286 m), the radius is half of the diameter, which is 0.1143 m. Therefore, the area of each plate is A = π * (0.1143 m)^2.
Now we can estimate the capacitance using the formula C = ε₀ * A / d.
C = (8.85 * 10^-12 F/m) * [π * (0.1143 m)^2] / 0.035 m = 3.67 * 10^-10 F (rounded to two significant figures)
Substituting the capacitance and the voltage into the formula for work done, we get:
W = 0.5 * (3.67 * 10^-10 F) * (12 V)^2 = 2.21 * 10^-8 J (rounded to two significant figures)
Therefore, the estimated work done by the battery to charge the plates is approximately 2.21 * 10^-8 J.
C) If a dielectric is inserted between the plates, the distance between the plates (d) will change, and therefore, the electric field and capacitance will also change. The electric field will decrease, and the capacitance will increase.
To learn more about electric field & work done calculation:
https://brainly.com/question/32255049
#SPJ11
Using the graph below answer the following questions about the Photo-electric effect.
a) What is the work function of the experimental photo-missive material?
b) What the threshold frequency of the experimental photo-missive material?
c) If the incoming frequency is 8.0 E14 Hz what would be the maximum kinetic energy of the most energetic electron?
d) If the incoming photon had a wavelength of 500.0 nm would you have a photo-electron ejected?
e) If you use a different experimental photo-missive material what would be the same on the graph?
f) What is the slope of the graph?
(a) The work function is 1.98 x 10⁻¹⁹ J.
(b) The threshold frequency is 3 x 10¹⁴ Hz.
(c) The maximum kinetic energy of the most energetic electron is 3.32 x 10⁻¹⁹ J.
(d) Photo-electron would be ejected.
(e) The only constant parameter would be speed of the photon.
(f) The slope of the graph is 6.67 x 10⁻³⁴ J.s
What is the work function of the experimental photo-missive material?(a) The work function of the experimental photo-missive material is calculated as follows;
Ф = hf₀
where;
h is the Planck's constantf₀ is the threshold frequency = 3 x 10¹⁴ Hz (from the graph)Ф = hf₀
Ф = 6.626 x 10⁻³⁴ x 3 x 10¹⁴
Ф = 1.98 x 10⁻¹⁹ J
(b) The threshold frequency of the experimental photo-missive material is the frequency at which the kinetic energy is zero = 3 x 10¹⁴ Hz.
(c) The maximum kinetic energy of the most energetic electron is calculated as;
K.E = E - Φ
K.E = ( 6.626 x 10⁻³⁴ x 8 x 10¹⁴) - 1.98 x 10⁻¹⁹ J
K.E = 3.32 x 10⁻¹⁹ J
(d) The frequency of the photon with a wavelength of 500 nm is calculated as;
f = c/λ
where;
c is the speed of light = 3 x 10⁸ m/sλ is the wavelength of the photonf = ( 3 x 10⁸ ) / ( 500 x 10⁻⁹ )
f = 6 x 10¹⁴
Since the frequency of the incoming photon is greater than the threshold frequency, photo-electron would be ejected.
(e) If you use a different experimental photo-missive material the only parameter that would be the same on the graph is speed of photon.
(f) The slope of the graph is calculated as;
m = (2.5 eV - 0 eV) / [(9 - 3) x 10¹⁴]
m = (2.5 ev) / (6 x 10¹⁴)
m = (2.5 x 1.6 x 10⁻¹⁹ ) / (6 x 10¹⁴ )
m = 6.67 x 10⁻³⁴ J.s
Learn more about work function here: https://brainly.com/question/19427469
#SPJ1
(1)Identify the possible differences of the voltage and configuration selection between the long distance HVDC and BTB HVDC.
(2)Power Electronic Device also follow the Moore’ Law. How will the Equivalent Distance change with the development of power electronics.
(3)Investigate the number of HVDC projects in the world and the total capacity of HVDC.
1. Differences in Voltage and Configuration Selection between long distance HVDC and BTB HVDC:HVDC stands for High Voltage Direct Current. It is a type of electrical transmission technology that utilizes direct current for the efficient transmission of bulk power over long distances and interconnections.
Long distance HVDC and Back-to-Back (BTB) HVDC are two types of HVDC systems used for power transmission. Both systems have different voltage and configuration selections. Long distance HVDC is used for transmission over long distances (above 400 km). On the other hand, BTB HVDC is used for interconnection between two adjacent power grids of different frequencies. The major differences between the two systems are the voltage level and the configuration. Long distance HVDC operates at high voltage levels, typically above 350 kV, and uses a point-to-point configuration for the transmission.
The converters used in the long-distance HVDC are large and can handle a high level of power transmission. In contrast, BTB HVDC operates at lower voltage levels, typically below 350 kV, and uses a back-to-back configuration. The converters used in the BTB HVDC are smaller and can handle lower levels of power transmission.
2. Equivalent Distance with the Development of Power Electronics:Power electronics is a branch of electrical engineering that deals with the conversion of electrical power from one form to another. Power electronic devices follow the Moore’s Law, which states that the number of transistors in a microprocessor doubles every two years. With the development of power electronics, the equivalent distance for power transmission will increase. Power electronic devices such as IGBTs (Insulated Gate Bipolar Transistors) have improved their power handling capacity and switching frequency, allowing the transmission of power over longer distances. This will lead to an increase in the equivalent distance for power transmission.
3. HVDC Projects and Total Capacity in the World:There are over 200 HVDC projects in the world with a total capacity of around 160 GW (gigawatts). China has the largest installed HVDC capacity of over 100 GW, followed by Europe with 25 GW. The largest HVDC project in the world is the Xiangjiaba-Shanghai transmission project in China, which has a capacity of 6.4 GW and a transmission distance of 1900 km.
The second-largest project is the Rio Madeira HVDC project in Brazil, which has a capacity of 3.15 GW and a transmission distance of 2370 km.
To learn more about Distance visit;
https://brainly.com/question/13034462
#SPJ11
A1. Consider the circuit in Figure A1. a) Calculate the equivalent resistance seen from the terminals of the current source. Re-draw the circuit using this equivalent resistance. b) Using your result
Given circuit:
[Figure A1]
(a) Calculation of equivalent resistance:
It can be observed from the given circuit that resistors R2 and R3 are in series. Hence, their equivalent resistance can be calculated as:
Req1 = R2 + R3
Req1 = 4 Ω + 6 Ω
Req1 = 10 Ω
Now, the equivalent resistance Req2 of Req1 and R1 can be calculated as:
Req2 = [(R1 × Req1) / (R1 + Req1)]
Req2 = [(8 Ω × 10 Ω) / (8 Ω + 10 Ω)]
Req2 = [(80 Ω) / (18 Ω)]
Req2 = 4.44 Ω (approximately)
Therefore, the equivalent resistance seen from the terminals of the current source is 4.44 Ω.
Re-drawing the circuit:
The given circuit can be re-drawn using the calculated equivalent resistance Req2 as shown below:
[Figure A1 - Re-drawn]
(b) Using the result:
The re-drawn circuit can be analyzed to calculate the current I that flows through the circuit. By using Ohm's Law, the voltage V across the equivalent resistance Req2 can be calculated as:
V = IR
Where, I is the current flowing through the circuit and R is the equivalent resistance. Therefore,
I = V / R
Now, the voltage V across Req2 can be calculated by applying Kirchhoff's Voltage Law (KVL) to the re-drawn circuit. The sum of the voltage drops across all the elements in a closed loop of the circuit should be zero.
Applying KVL, we have:
V - IR1 - IReq1 = 0
V - 8I - 10I = 0
V = 18I
Thus, V = 18 × I
Now, substituting the value of Req2 in the above equation, we get:
V = 18 × I × 4.44
V = 79.9 × I
Since the current source in the given circuit is 3 A, we can find the value of the current I flowing through the circuit as:
3 A = V / Req2
3 A = (79.9 × I) / 4.44
I = (3 × 4.44) / 79.9
I = 0.167 A (approximately)
Therefore, the current flowing through the circuit is 0.167 A (approximately).
To know more about Calculation visit:
https://brainly.com/question/30781060
#SPJ11
Force acting between two argons are well approximated by the LennardJones potential given by U(r)=
r
12
a
−
r
6
b
. Find the equilibrium separation distance between the argons.
The Lennard-Jones potential for the force acting between two argons is given by:U(r)= (a/r)^12 - (b/r)^6where, r is the distance between the two argon atoms and a and b are constants.The equilibrium separation distance between the argons is given by the minimum value of U(r). Thus, we differentiate U(r) with respect to r and equate it to zero to find the minimum value.U'(r) = -12a^12/r^13 + 6b^6/r^7At the minimum value, U'(r) = 0⇒ -12a^12/r^13 + 6b^6/r^7 = 0⇒ 2(a/r)^12 = (b/r)^6⇒ (a/r)^6 = b^3/r^6⇒ r = (b/a)^(1/6)Thus, the equilibrium separation distance between the argons is given by r = (b/a)^(1/6).Answer: The equilibrium separation distance between the argons is given by r = (b/a)^(1/6).
The equilibrium separation distance between the argon is given by r = (b/a)^(1/6).
The Lennard-Jones potential for the force acting between two argon is given by: U(r)= (a/r)^12 - (b/r)^6, where r is the distance between the two argon atoms and a and b are constants.
The equilibrium separation distance between the argon is given by the minimum value of U(r).
Thus, we differentiate U(r) with respect to r and equate it to zero to find the minimum value: U'(r) = -12a^12/r^13 + 6b^6/r^7
At the minimum value, U'(r) = 0⇒ -12a^12/r^13 + 6b^6/r^7 = 0⇒ 2(a/r)^12 = (b/r)^6⇒ (a/r)^6 = b^3/r^6⇒ r = (b/a)^(1/6)
Thus, the equilibrium separation distance between the argon is given by r = (b/a)^(1/6).
To know more about force refer to:
https://brainly.com/question/25239010
#SPJ11
Prior to cooking you mix in a pan 100 g of cooking oil A which is initially at 60C with 200 g of cooking oil B which is initially at 30C. You then add 300 g of oil C initially at 20C and mix this in as well. Assume that the mixing happens so quickly that there is no heat transfer between the pan and the oils and that the heat capacity of each oil is identical. The new scenario is below: Instead of mixing the oils as described above, you mix 200 g of oil B at 30C and 300 g of oil C at 20C in the pan to start with and then add 100 g of oil A at 60C. (That is, both the quantities and initial temperatures are the same). What is the temperature of the mixture of oils in the pan after all three oils are mixed in?
On solving these equations, we get:T = (2 × 30 + 3 × 20 + 60) / 7 = 37.1°CTherefore, the final temperature of the oil mixture in the second case is 37.1°C.Hence, the temperature of the mixture of oils in the pan after all three oils are mixed in is 37.1°C.
In the given problem, the mixing of the oils is done so quickly that there is no heat transfer between the pan and the oils. Also, the heat capacity of each oil is identical. Now, let's solve the given problem. Initial quantities and temperatures of the oils:100 g of cooking oil A at 60°C200 g of cooking oil B at 30°C300 g of oil C at 20°C First case:In this case, we mix 100 g of oil A with 200 g of oil B and 300 g of oil C. Using the law of heat transfer, we can write:Q1
= Here, Q1 is the heat gained by oil A and Q2 is the heat lost by oils B and C.We know that,Q
= mC(T2 - T1), where m is the mass of the oil, C is the specific heat of the oil and T2 - T1 is the change in temperature.So, for oil A,Q1
= 100 × C × (T - 60) (Since oil A gains heat)For oils B and C,Q2
= 200 × C × (T - 30) + 300 × C × (T - 20) (Since oils B and C lose heat)On solving these equations, we get:T
= (2 × 60 + 3 × 20 + 2 × 30) / 7
= 34.3°C Therefore, the final temperature of the oil mixture in the first case is 34.3°C.Second case:In this case, we mix 200 g of oil B and 300 g of oil C first and then add 100 g of oil A.Using the same approach as above, we can write:Q1
= Q2 Here, Q1 is the heat gained by oil B and C and Q2 is the heat lost by oil A.We know that,Q
= mC(T2 - T1), where m is the mass of the oil, C is the specific heat of the oil and T2 - T1 is the change in temperature.So, for oils B and C,Q1
= 200 × C × (T - 30) + 300 × C × (T - 20) (Since oils B and C gain heat)For oil A,Q2
= 100 × C × (60 - T) (Since oil A loses heat).On solving these equations, we get:T
= (2 × 30 + 3 × 20 + 60) / 7
= 37.1°C Therefore, the final temperature of the oil mixture in the second case is 37.1°C.Hence, the temperature of the mixture of oils in the pan after all three oils are mixed in is 37.1°C.
To know more about equations visit:
https://brainly.com/question/29657983
#SPJ11
A rock was dropped from a tall building and it took 3 seconds to hit the ground What is the height of the building in the unit meter? No need to write the unit. Please write the answer in one decimal place leg. 1.234 should be written as 1.2).
The height of the building from which the rock was dropped is approximately 44.1 meters, a rock was dropped from a tall building and it took 3 seconds to hit the ground.
To determine the height of a building in meters, in which a rock was dropped from the roof and hit the ground after three seconds, we will use the formula for free fall.
This formula is as follows:
h = 1/2 gt² where is the height from which the object was dropped,
g is the gravitational acceleration (9.81 m/s²)t is the time it takes for the object to fall to the ground given that the rock took 3 seconds to hit the ground,
we will substitute t = 3 seconds in the above acceleration formula.
Then, we will solve for h-
h = 1/2 x 9.81 m/s² x (3 seconds)²
= 44.145 meters (rounded to one decimal place)
Therefore, the height of the building from which the rock was dropped is approximately 44.1 meters.
To know more about free fall please refer:
https://brainly.com/question/12167131
#SPJ11
Figure below illustrates a solid, square pinewood raft which measures \( 6.0 \mathrm{~m} \) on the sides and is \( 0.45 \mathrm{~m} \) thick. 2.3.1 State Archimedes' principle. 2.3.2 Determine whether
2.3.1 According to Archimedes' principle, the buoyant force on a submerged object is equal to the weight of the fluid it displaces.
2.3.2 The given pinewood raft floats in water because the buoyant force is greater than its weight.
2.3.3 Approximately 0.45 meters of the raft is submerged beneath the water's surface.
2.3.1 Archimedes' principle states that when a body is submerged in a fluid, it experiences an upward buoyant force equal to the weight of the fluid it displaces.
2.3.2 To determine if the raft floats or sinks in water, we need to compare the weight of the raft to the buoyant force acting on it. The weight of the raft can be calculated by multiplying its volume by the density of the material (assuming a uniform density). The volume of the raft can be found by multiplying the area of its base by its thickness.
The sides of the square raft measure 6.0 m and its thickness is 0.45 m, the base area is (6.0 m)² = 36 m². The volume of the raft is then 36 m² * 0.45 m = 16.2 m³ (cubic meters).
Assuming the raft is made of pinewood, we can estimate its density to be around 450 kg/m³.
The weight of the raft is given by the formula W = m * g, where m is the mass and g is the acceleration due to gravity (approximately 9.8 m/s²). Since density (ρ) is defined as mass per unit volume (ρ = m/V), we can rewrite the formula as W = ρ * V * g.
Substituting the values, we have W = (450 kg/m³) * (16.2 m³) * (9.8 m/s²) = 710,820 N.
Now, let's calculate the buoyant force acting on the raft. The buoyant force is equal to the weight of the water displaced by the raft. Since the raft is fully submerged, the buoyant force is equal to the weight of the water with the same volume as the raft. The density of water is approximately 1000 kg/m³.
The buoyant force is given by the formula [tex]F_b[/tex] = [tex]\rho_w[/tex] * [tex]V_r[/tex] * g, where [tex]\rho_w[/tex] is the density of water and [tex]V_r[/tex] is the volume of the raft. Substituting the values, we have [tex]F_b[/tex] = (1000 kg/m³) * (16.2 m³) * (9.8 m/s²) = 158,760 N.
Comparing the weight of the raft (710,820 N) to the buoyant force (158,760 N), we can see that the buoyant force is greater. Therefore, the raft floats in water.
2.3.3 If the raft floats, the amount of the raft submerged beneath the surface can be determined using the equation for buoyancy. The buoyant force ([tex]F_b[/tex]) is equal to the weight of the water displaced by the submerged portion of the raft.
The volume of water displaced is equal to the volume of the submerged portion of the raft. Since the raft is square-shaped, the submerged portion has the same base area as the whole raft (36 m²) and a height (h) determined by the portion submerged.
Using the formula for volume (V = A * h), where A is the base area and h is the height, we can write [tex]V_w[/tex] = 36 m² * h.
Equating the buoyant force to the weight of the displaced water, we have [tex]F_b[/tex] = [tex]\rho_w[/tex] * [tex]V_w[/tex] * g, where [tex]\rho_w[/tex] is the density of water.
Substituting the known values, 158,760 N = (1000 kg/m³) * (36 m² * h) * (9.8 m/s²).
Simplifying the equation, we can solve for h:
h = 158,760 N / (1000 kg/m³ * 36 m² * 9.8 m/s²) ≈ 0.45 m.
Therefore, approximately 0.45 meters of the raft is beneath the water's surface.
To know more about Archimedes' principle, refer to the link below:
https://brainly.com/question/787619#
#SPJ11
Complete Question:
2.3 Figure below illustrates a solid, square pinewood raft which measures 6.0 m on the sides and is 0.45 m thick. 2.3.1 State Archimedes' principle. 2.3.2 Determine whether the raft floats or sinks in water. 2.3.3 If it floats, how much of the raft is beneath the surface (see the distance h in figure above).
Do these values of LED Planck's contant agree with the
theoretical value: 6.63 x 10–34 J s?
Red LED: h= 5.449 x10-³4 J s; dh ±0.004 x10-34 J s Yellow LED: h = 5.057 x10-34 J s; dh ±0.003 x10-34 J s Green LED: h = 4.887 x10-³4 J s; dh ±0.003 x10-34 J s Blue LED: h = 7.140 x10-34 J s; dh
The percent error is negative in each case, indicating that the experimental value is less than the theoretical value. Therefore, the experimental values of LED Planck's constant do not agree with the theoretical value of 6.63 × 10−34 J s.
Planck's constant is a universal constant that relates the energy of a photon to its frequency, which is essential to the study of quantum mechanics. The theoretical value of Planck's constant is 6.63 × 10−34 J s. The values for LED Planck's constant are given below. Red LED: h
= 5.449 × 10−34 J s, dh ± 0.004 × 10−34 J s Yellow LED: h
= 5.057 × 10−34 J s, dh ± 0.003 × 10−34 J s Green LED: h
= 4.887 × 10−34 J s, dh ± 0.003 × 10−34 J s Blue LED: h
= 7.140 × 10−34 J s, dh are given. To determine whether the values of LED Planck's constant agree with the theoretical value of 6.63 × 10−34 J s, it is necessary to calculate the percent error between the theoretical and experimental values for each LED using the formula for percent error. Percent error
= (Experimental value - Theoretical value) / Theoretical value × 100% Red LED: Percent error
= [(5.449 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= -17.8% Yellow LED: Percent error
= [(5.057 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= -23.7% Green LED: Percent error
= [(4.887 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= -26.3% Blue LED: Percent error
= [(7.140 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= 7.7%.The percent error is negative in each case, indicating that the experimental value is less than the theoretical value. Therefore, the experimental values of LED Planck's constant do not agree with the theoretical value of 6.63 × 10−34 J s.
To know more about experimental visit:
https://brainly.com/question/33446957
#SPJ11
Design a simple circuit from the function F by reducing it using appropriate k-map , draw corresponding Logic Diagram for the simplified ExpressionF( w,x,y,z)=Σm(1,3,4,8,11,15)+d(0,5,6,7,9)
Logic maps have numerous applications. They serve as the primary diagram for the design of solid state components like computer chips in the solid state industry.
The reader must comprehend what each of the specialized symbols in logic diagrams stand for in order to read and interpret them.
Thus, Mathematicians utilize them to assist in the resolution of logical issues. However, their ability to show component and system operational information is their primary application at industrial facilities.
A diagram created using logic symbology enables the user to ascertain how a specific system or component will function as multiple input signals change.
The reader must comprehend what each of the specialized symbols in logic diagrams stand for in order to read and interpret them.
Thus, Logic maps have numerous applications. They serve as the primary diagram for the design of solid state components like computer chips in the solid state industry.
Learn more about Logic maps, refer to the link:
https://brainly.com/question/33368379
#SPJ4
The energies of a two-level system are ±E. Consider an ensemble of such non-interacting systems at a temperature T. At low temperatures, the leading term in the specific heat depends on T as दवि-स्तरीय तंत्र के लिए ऊर्जायें ±E है। तापमान T पर ऐसे अन्योन्यक्रियाहीन तंत्रों के समुदाय पर विधार करें। निम्न तापमान पर, विशिष्ट उष्मा का अयग पद T पर निम्नवत् निर्भर है Options:- .
T
2
1
e
−E/k
B
T
Option ID :- 19
T
2
1
e
−2E/k
B
T
Option ID :- 198, - T
2
e
−E/k
B
T
Option ID :- 199, T
2
e
−2E/k
B
T
At low temperatures, the leading term in the specific heat of a two-level system depends on T as [tex]T^2e^{-2E/k_B}[/tex]. Therefore, option (D) is correct.
In a two-level system with energies ±E, when considering an ensemble of non-interacting systems at temperature T, the specific heat behavior can be described by the leading term. At low temperatures, this term depends on T as[tex]T^2e^{-2E/k_B}[/tex].
The specific heat of a system measures its ability to absorb or release heat. In the case of a two-level system, it refers to the amount of energy required to increase its temperature. At low temperatures, the dominant contribution to the specific heat arises from the thermal excitation of the higher energy level.
The expression [tex]T^2e^{-2E/k_B}[/tex] captures the temperature dependence of this specific heat term. As the temperature increases, the exponential term decreases, leading to a decrease in the specific heat. This behavior is characteristic of a two-level system, where the energy separation between levels influences the thermal properties and contributes to the overall specific heat response at low temperatures.
Learn more about specific heat, here:
https://brainly.com/question/31608647
#SPJ4
When is the photoelectric effect observed?
The photoelectric effect is observed when light interacts with matter, specifically when photons (particles of light) transfer their energy to electrons in an atom or a material. The correct answer is A. When an electric current results from light shining on a surface.
In the early 20th century, Albert Einstein provided a groundbreaking explanation of the photoelectric effect, which earned him the Nobel Prize in Physics in 1921. His work established the dual nature of light, both as a wave and as a particle (photon). Here's a detailed explanation of the photoelectric effect:
When light shines on a surface, it is composed of photons that carry energy. These photons interact with electrons in the material. The photoelectric effect occurs when photons transfer their energy to electrons, causing them to be emitted from the material.
The process can be described in several steps:
1. Absorption: When a photon with sufficient energy interacts with an electron in an atom or material, it can be absorbed. The energy of the photon is transferred to the electron, promoting it to a higher energy level or even releasing it from the atom.
2. Ejection: If the energy of the absorbed photon is greater than or equal to the binding energy of the electron (also known as the work function), the electron can be ejected from the material. The work function represents the minimum energy required to remove an electron from the material's surface.
3. Electron emission: The ejected electron can now contribute to the formation of an electric current. If there is a conducting material connected to the surface, the released electron can move through the material, resulting in the flow of electric charge.
The photoelectric effect is not observed when light acts solely as a wave (option B). While light does exhibit wave-like properties, such as interference and diffraction, these phenomena do not directly involve the transfer of energy from photons to electrons.
Option C, "When an electric current causes light to be produced," does not accurately describe the photoelectric effect. The photoelectric effect involves the emission of electrons due to the interaction of light with matter, but it does not directly produce light as a result of an electric current.
Option D, "Any time an electric current is produced," is a broad statement that encompasses various phenomena beyond the photoelectric effect. Electric currents can be produced in various ways, such as through the flow of charged particles or the movement of electrons in a conductor. The photoelectric effect is a specific phenomenon that occurs when light interacts with matter and results in the emission of electrons.
To summarize, the photoelectric effect is observed when light shines on a surface, and the energy of photons is transferred to electrons, leading to their emission from the material. This emission of electrons can result in the formation of an electric current.
For more questions on photons, click on:
https://brainly.com/question/15946945
#SPJ8
I think it is the question:
When is the photoelectric effect observed?
A. When an electric current results from light shining on a surface
B. When light acts as a wave
C. When an electric current causes light to be produced
D. Any time an electric current is produced .
2. (20 points, 5 points each) An analog signal, x(t), has a bandwidth of 30k Hz.
a) What is the Nyquist rate for x(t)?
b) Assume you sampled the analog signal, x(t), using a sampling frequency of 60k Hz and obtained a discrete-time signal x1[n], what is the highest non-zero frequency component in xi[n]? (Note that the frequency range for discrete- time sequence is [0, 1], where it is the highest frequency component)
c) With the sampling frequency of 60k Hz, if you want to design a discrete-time low-pass filter h[n] to filter out all frequency components beyond 6k Hz in x(t), what is the cut-off frequency of h[n]? (Note that the frequency range for discrete-time sequence is [0, 1], where it is the highest frequency component) ,
d) Assume you sampled the analog signal, x(t), using a sampling frequency of 80k Hz and obtained a discrete-time signal x2[n], what is the highest non-zero frequency component in x2[n]?
a) The Nyquist rate for x(t) is twice the bandwidth of the signal. Therefore, the Nyquist rate is 2 * 30 kHz = 60 kHz.
b) If the analog signal x(t) is sampled using a sampling frequency of 60 kHz, according to the Nyquist-Shannon sampling theorem, the highest non-zero frequency component in the discrete-time signal xi[n] will be half of the sampling frequency, which is 30 kHz.
c) To design a discrete-time low-pass filter h[n] to filter out all frequency components beyond 6 kHz in x(t), we need to set the cut-off frequency of the filter based on the Nyquist rate. Since the Nyquist rate is 60 kHz, we want to set the cut-off frequency at 6 kHz. Therefore, the cut-off frequency of h[n] is 6 kHz / 60 kHz = 0.1.
d) If the analog signal x(t) is sampled using a sampling frequency of 80 kHz, the highest non-zero frequency component in the discrete-time signal x2[n] will be half of the sampling frequency, which is 40 kHz.
Learn more about Nyquist rate from the given link!
https://brainly.in/question/6072902
#SPJ11
Question Two SO Fig Q2 shows a thin steel rotor disc of outside diameter 360mm with a central hole of diameter 120mm and the disc is made to rotate at a speed of 6900rev/min. (i) Sketch the distribution of the radial stress (o,) and the circumferential stress (0) across the thickness (ii) Calculate the change in thickness of this disc at this speed. E = 200GN / m : v=0.3p = 7800kg/m The general expressions for the radial stress (o,) and the Circumferential stress (o) in a rotating cylinder are given by 0 = A B p? B - (3 + over: (30) 8 1+ 30 o = A + 2 8"Jaw'yo ? p' is the density and v' is the Poisson's ratio of the steel rotor and A and B are constants.
(i) [tex]= (4320p/86400) - (p*t²/30)ρ²[/tex], The general expressions for the radial stress (σr) and the Circumferential stress (σθ) in a rotating cylinder are given by; σθ = A + Bρ²σr = A − Bρ² ; (ii) The change in thickness of the rotor disc at 6900 rev/min is -0.19 mm (decrease).
(i) Sketch the distribution of the radial stress (σr) and the circumferential stress (σθ) across the thickness:
A thin steel rotor disc of an outside diameter of 360 mm with a central hole of diameter 120 mm and the disc is made to rotate at a speed of 6900 rev/min.
Given: E = 200 GN/m2v
= 0.3ρ
= 7800 kg/m³
The general expressions for the radial stress (σr) and the Circumferential stress (σθ) in a rotating cylinder are given by; σθ = A + Bρ²σr = A − Bρ² Where, A and B are constants. We can determine the values of A and B as follows: At ρ = 0;
σr = σhoop
= (p*r²)/t
= (p*180²)/(15)
= 4320p
At ρ = r;
σr = σhoop
= (p*r²)/t
= (p*360²)/(15)
= 8640p
Substituting these values of ρ and σr into the above equation, we have;[tex]σhoop = A - B (r/t)²-----------------(1)[/tex]
[tex]σhoop = A - B (360/t)²-----------------(2)[/tex]
Subtracting equation (1) from equation (2),
we get; 8640p - 4320p
[tex]= B{(360/t)² - (180/t)2}4320p[/tex]
= (180*360/t²)*B
Therefore; B = (4320p*t²)/(180*360)B
[tex]= p*t²/30[/tex]
substituting the value of B in equation (1)4320p = A - p*t²/30A
[tex]= 4320p + p*t²/30A[/tex]
= 4320p(1 + t²/86400)[tex]= (180*360/t²)*B[/tex]
Therefore;
[tex]σθ = (4320p/86400) + (p*t²/30)ρ²σr[/tex]
[tex]= (4320p/86400) - (p*t2/30)ρ²[/tex]
(ii) Substituting the values of the given parameters in the above equations, we get;
[tex]σθ = (4320*7800/86400) + (7800*0.3*10^9/(30*86400))*((180/2)*10^-3)^2σθ[/tex]
= 7050 N/m²σr
[tex]= (4320*7800/86400) - (7800*0.3*10^9/(30*86400))*((180/2)*10^-3)^2σr[/tex]
= 5430 N/m²
Now the shear stress can be obtained by using the relation;τ = (r/2)*((σr - σθ)/r)τ
=[tex](180/2)*((5430-7050)/180)*10^3τ[/tex]
= -990 N/m²
Shear stress (τ) is negative indicating that the rotor disc will decrease in thickness.
The change in thickness of the rotor disc can be calculated as follows; τ = Gδ/tδ
= τt/Gδ
=[tex](-990)*(15*10^-3)/78.6*10^9δ[/tex]
= -0.00019 m
= -0.19 mm.
Therefore, the change in thickness of the rotor disc at 6900 rev/min is -0.19 mm (decrease).
To know more about radial stress, refer
https://brainly.com/question/15991912
#SPJ11
A sleeve bearing is to have an L/D ratio of 1.0 and an allowable bearing pressure of 0.5 MN/m². Find the inside diameter and the length of the bearing if it is to sustain a load of 2550 N
Calculate the inside diameter and the length of the sleeve bearing, we need to use the bearing equation as follows: Load on bearing = Bearing pressure x Projected area of bearing
Load on bearing = (π/4) x (D² - d²) x L x P
where
D = outside diameter of bearing
d = inside diameter of bearing
L = length of the bearing
P = allowable bearing pressure
Using the L/D ratio, we have: L/D = L/d = 1.0 ⇒ L = d Let the inside diameter be d, then the outside diameter is D = d + 2L = 3d Substituting the given values in the bearing equation, we have:
2550 N = (0.5 MN/m²) x (π/4) x (3d² - d²) x d
2550 N = (0.5 MN/m²) x (π/4) x 8d³
2550 N = (1.5708 MN/m³) x d³
d³ = 2550 N ÷ (1.5708 MN/m³ x 8)
≈ 204.2 x 10⁻⁶ m³
d ≈ 0.579 m
Using L/D ratio, L = d = 0.579 m, and
D = 3d = 1.737 m
To know more about pressure visit:
https://brainly.com/question/30673967
#SPJ11
You are asked to design a resistor using an intrinsic semiconductor bar of length Land a cross-sectional area A. The scattering rate for electrons and holes are both 1/t, and the effective mass for holes is mp* which is two times larger than the effective mass for electrons. The bandgap is G. Assume T=300K. Obtain an expression for the current in the bar in terms of the parameters given if a voltage Vp is applied across the bar. Sketch the bar with the voltage applied and show with arrows indicating the directions of Electric Field and current densities.
The expression for the current in the intrinsic semiconductor bar with a voltage Vp applied across it is I = Vp * A * (2q * n * L) / t, where I is the current, Vp is the applied voltage, A is the cross-sectional area, n is the electron concentration, L is the length of the bar, q is the charge of an electron, and t is the scattering rate.
In designing a resistor using an intrinsic semiconductor bar, with a voltage Vp applied across the bar, the expression for the current in the bar can be obtained using Ohm's Law and the concept of drift current.
The current density (J) in the semiconductor bar can be expressed as:
J = q * n * μn * E - q * p * μp * E
where:
- q is the charge of an electron
- n is the electron concentration
- μn is the electron mobility
- p is the hole concentration
- μp is the hole mobility
- E is the electric field
Considering the continuity equation for current in the semiconductor bar, we have:
dJ/dx = - q * (dp/dt + dn/dt)
Since we have an intrinsic semiconductor (where n = p), the expression simplifies to:
dJ/dx = - 2q * dn/dt
Using the scattering rate given (1/t), we can express the change in the electron concentration as:
dn/dt = -(n/t)
Substituting this back into the equation, we get:
dJ/dx = 2q * (n/t)
Integrating both sides with respect to x, we obtain:
J = 2q * (n/t) * x + C
where C is the integration constant. Since the bar length is L, we can substitute x = L and rearrange the equation to solve for the current (I):
I = J * A = 2q * (n/t) * L * A
Finally, using Ohm's Law (V = IR), we can express the current in terms of the applied voltage Vp:
I = Vp * A * (2q * n * L) / (t)
Therefore, the expression for the current in the semiconductor bar, considering the given parameters, is:
I = Vp * A * (2q * n * L) / (t)
Regarding the sketch of the bar with the applied voltage, it is not possible to provide a visual representation in a text-based format. However, it is important to note that the electric field (E) and current density (J) will be in the direction opposite to each other, following the direction of the applied voltage Vp.
To know more about intrinsic semiconductor refer here
https://brainly.com/question/16172570#
#SPJ11
The back side of a polished spoon
has f = -6.50 cm (convex). If you
hold your nose 5.00 cm from it
what is its magnification?
(Mind your minus signs.)
(this question is on acellus pls help )
The back side of a polished spoon has f = -6.50 cm (convex). If you
hold your nose 5.00 cm from it then the magnification of the image is
0.864.
The formula for calculating magnification in such a case is: Magnification = -di/do
Here, f = -6.50 cm is the focal length of the mirror, and the object is the back side of a polished spoon.
The distance between the object and the mirror, in this case, is the distance between your nose and the spoon, which is 5.00 cm.
Thus, the distance of the image from the mirror is:di = -f/(1/do - 1/f)
Putting the values in the formula, we get:di = -6.50/(1/5 - 1/-6.50) = -4.32 cm (negative sign indicates that the image is virtual)
Using the magnification formula, we have: Magnification = -di/do = -(-4.32)/5.00 = 0.864
Thus, the magnification of the image is 0.864.
For more questions on magnification
https://brainly.com/question/15744335
#SPJ8
Two carts mounted on an air track are moving toward one another. Cart 1has a speed of 1.1 m/s and a mass of 0.42 kg. Cart 2 has a mass of 0.71 kg. (a) If the total momentum of the system is to be zero, what is the initial speed (in m/s ) of Cart 2? (Enter a number.) m/s (b) Does it follow that the kinetic energy of the system is also zero since the momentum of the system is zero? Yes No (c) Determine the system's kinetic energy (in J) in order to substantiate your answer to part (b). (Enter a number.) J
a) initial speed of Cart 2 is approximately 0.651 m/s.
b) No, it does not follow that the kinetic energy of the system is also zero
c) system's kinetic energy is approximately 0.483 J.
(a) For initial speed of Cart 2, we can use the principle of conservation of momentum. The total momentum before the collision is equal to the total momentum after the collision. Since the total momentum of the system is to be zero,
The momentum of an object is calculated by multiplying its mass by its velocity. So, we have:
Momentum of Cart 1 = Mass of Cart 1 * Velocity of Cart 1
Momentum of Cart 2 = Mass of Cart 2 * Velocity of Cart 2
Since the total momentum of the system is zero, we can set up the following equation:
0 = (0.42 kg * 1.1 m/s) + (0.71 kg * Velocity of Cart 2)
Solving for the velocity of Cart 2:
0 = 0.462 kg*m/s + (0.71 kg * Velocity of Cart 2)
-0.462 kg*m/s = 0.71 kg * Velocity of Cart 2
Velocity of Cart 2 = -0.462 kg*m/s / 0.71 kg
Velocity of Cart 2 ≈ -0.651 m/s
Therefore, the initial speed of Cart 2 is approximately 0.651 m/s.
(b) No, it does not follow that the kinetic energy of the system is also zero just because the momentum of the system is zero. Kinetic energy depends on the mass and velocity of an object, while momentum only considers the mass and velocity. Therefore, the kinetic energy can still be non-zero even if the momentum is zero.
(c) For system's kinetic energy, we can calculate the individual kinetic energies of Cart 1 and Cart 2, and then sum them up. The kinetic energy (KE) of an object is given by the formula:
KE = (1/2) * Mass * Velocity^2
The kinetic energy of Cart 1 is:
KE1 = (1/2) * 0.42 kg * (1.1 m/s)^2
The kinetic energy of Cart 2 is:
KE2 = (1/2) * 0.71 kg * (-0.651 m/s)^2
To find the total kinetic energy of the system, we add the individual kinetic energies together:
Total kinetic energy = KE1 + KE2
Total kinetic energy = 0.332 J + 0.151 J
Total kinetic energy = 0.483 J
Therefore, the system's kinetic energy is approximately 0.483 J.
To learn more about kinetic energy and Momentum :
https://brainly.com/question/12880315
#SPJ11
predict the ground state electron configuration of the following ions
To predict the ground state electron configuration of ions, we need to consider whether the ion is a cation or an anion. cations lose electrons, while anions gain electrons. For example, the electron configuration of the sodium ion (Na+) is 1s2 2s2 2p6, and the electron configuration of the chloride ion (Cl-) is 1s2 2s2 2p6 3s2 3p6.
To predict the ground state electron configuration of ions, we need to consider whether the ion is a cation or an anion. cations are formed when atoms lose electrons, while anions are formed when atoms gain electrons.
Let's take a look at some examples:
Sodium ion (Na+): Sodium (Na) has an electron configuration of 1s2 2s2 2p6 3s1. Since it loses one electron to become a cation, the electron configuration of the sodium ion is 1s2 2s2 2p6.Chloride ion (Cl-): Chlorine (Cl) has an electron configuration of 1s2 2s2 2p6 3s2 3p5. Since it gains one electron to become an anion, the electron configuration of the chloride ion is 1s2 2s2 2p6 3s2 3p6.Remember, cations lose electrons and anions gain electrons when predicting the ground state electron configuration of ions.
Learn more:About predict here:
https://brainly.com/question/5958146
#SPJ11
Write the electron configuration of the neutral atom. Then remove the number of electrons equal to the charge of the ion to determine the ion's electron configuration. In the ground state, an atom's electrons will always fill the orbitals with the lowest energy levels first.
The most common method for writing electron configurations is to write the orbitals' subshells in order of increasing energy, filling in the electrons as they are added. As we move to larger atoms, we fill in more orbitals, and the electron configurations become increasingly complex.
For example, let's determine the ground state electron configuration of the following ions:Fe2+First, we need to write the electron configuration of the neutral atom Fe:1s²2s²2p⁶3s²3p⁶4s²3d⁶Next, we remove two electrons since the charge of the ion is 2+.So, the ground state electron configuration of Fe2+ is:1s²2s²2p⁶3s²3p⁶3d⁶
To know more about electron configuration visit:-
https://brainly.com/question/29157546
#SPJ11