The density of platinum is 2.2 x 10 kg/m³. Determine the mass m of a cube of platinum that is 4.0 cm x 4.0 cm x 4.0 cm in size. m= x10 I TOOLS kg

Answers

Answer 1

The mass of the cube is 6.016 kg

The density of platinum is 2.2 x 10³ kg/m³.

Determine the mass m of a cube of platinum that is 4.0 cm x 4.0 cm x 4.0 cm in size.

m = 2.2 x 10³ kg/m³ x (4.0 x 10⁻² m)³

= 6.016 kg

Density of an element is expressed in kg/m³. The volume of a cube can be found by cubing the length of any side of a cube.

The mass of a cube of platinum can be found by multiplying the volume of the cube by its density.

The formula for finding mass of an object is:

m = V x D,

where V is the volume of the object and D is the density of the object

In this case, the dimensions of the cube are provided to be 4.0 cm x 4.0 cm x 4.0 cm which can be converted to meters as follows:

4.0 cm = 4.0 x 10⁻² m

So, the volume of the cube is

V = 4.0 x 10⁻² m x 4.0 x 10⁻² m x 4.0 x 10⁻² m

= 6.4 x 10⁻⁵ m³.

Substituting the given values into the formula, the mass of the cube can be calculated as:

m = 2.2 x 10³ kg/m³ x 6.4 x 10⁻⁵ m³

= 6.016 kg

To know more about mass visit:

https://brainly.com/question/11954533

#SPJ11


Related Questions

Question 11 The electric field of a plane wave propagating in a nonmagnetic material is given by E=(3y^​+4z^)cos(1.0π×108t−1.34πx)(V/m). Find the relative permittivity of the material εr​. εr​= Your Answer: Answer Question 12 A 3.0MHz frequency plane wave propagates in a medium characterized by εT​=3.0. μr​=1.5, and σ=5.0( S/m). Calculate α. α= Your Answer: ​ Answer Question 13 A parallel-polarized ( p-wave) plane wave is incident from air onto a dielectric medium with εr​=4. At what incident angle θi​ there will be no reflection? Answer to the 4th digit precision after the decimal place (eg. 1.2345). θi​=(rad). Your Answer: Answer Question 14 A plane wave with a frequency of f=1.5MHz and electric field amplitude of 9 (V/m) is normally incident in air onto the plane surface of a semi-infinite conducting material with a relative permittivity εr​=7.3, relative permeability μr​=1, and conductivity σ=110(5/m). Determine the transmitted power per unit cross sectional area in a 2.2 mm penetration of the conducting medium. Answer to the 4 th digit precision after the decimal place (eg. 1.2345). Your Answer: Answer

Answers

Question 11

The electric field of a plane wave propagating in a non-magnetic material is given by the following equation;

E=(3y^+4z^)cos(1.0π×108t−1.34πx)(V/m)

The relative permittivity of the material εr​ is;

εr​=1+(1/3.0)[(3y^+4z^)cos(1.0π×108t−1.34πx)/E0]^2

εr​=1+(1/3.0)[(3^2+4^2)cos^2(1.0π×108t−1.34πx)/E0]^2

εr​=1+(1/3.0)[25cos^2(1.0π×108t−1.34πx)/E0]^2

εr​=1+(1/3.0)(25/81)

εr​=1.31

Question 12

The propagation constant, α is given by the following equation;

α=ω√(μrεr(1+jσ/ωεr))

Where;

σ = 5.0 S/m; εr​=3.0; μr​=1.5; and f = 3.0 MHz

The angular frequency, ω is given by;

ω=2πf = 2 x π x 3.0 x 10^6 rad/s

Substituting the given parameters;

α=2π x 3.0 x 10^6 √(1.5 x 3.0(1+j5.0 x 10^-6 x 3.0)/(3.0))

α=2.502 x 10^5 Np/m

Question 13

The critical angle of incidence, θc is given by the equation;

sinθc=1/εr​

sinθc=1/4θ

c=asin(1/4)

 = 14.48 degrees

For total internal reflection to occur, the incident angle, θi​ must be greater than the critical angle of incidence, θc;θi​>θcθi​>14.48 degrees

Question 14

The power of the transmitted wave through a given depth, z is given by the equation;

P(z)=E2/2ρcT

Where;E = 9 V/m;ρc = μr​μo/εr​εo = 3 x 10^8 m/s; εo = 8.85 x 10^-12 F/m; z = 2.2 mm

The wave impedance is given by;

η = sqrt(μr​μo/εr​εo)

  = sqrt(1 x 4π x 10^-7/7.3 x 8.85 x 10^-12)

  = 226.46 Ω

The transmitted power per unit cross-sectional area in a 2.2 mm penetration of the conducting medium is given by;

P(z)=E2/2ρcT

     = (9/2 x 226.46 x 3 x 10^8) x e^(-2σz)P(z)

     =6.14 x 10^-9 W/m^2

Learn more about electric field from :

https://brainly.com/question/19878202

#SPJ11

A later observation of the object from question 2 was made and it was discovered that the dark lines are shifted by 15 nm to longer wavelengths than expected.
a) What does the shift in the wavelength tell us about the motion of the object?
b) A second star is observed to have its lines shifted by 20 nm to shorter wavelengths. Which of these two stars is moving the fastest?

Answers

A)  The shift in the wavelength towards longer wavelengths indicates that the object observed in question 2 is moving away from the observer.

This phenomenon is known as redshift. When an object moves away from an observer, the wavelengths of light emitted by the object appear stretched or shifted towards longer wavelengths. This shift can be explained by the Doppler effect, which occurs due to the relative motion between the source of light (the object) and the observer.

B) The second star, which has its lines shifted by 20 nm to shorter wavelengths, is moving faster compared to the object in question 2. This shift towards shorter wavelengths is known as blueshift.

When an object moves towards an observer, the wavelengths of light emitted by the object appear compressed or shifted towards shorter wavelengths. Similar to the redshift, this blueshift is also explained by the Doppler effect. The greater the blueshift, the faster the object is moving towards the observer. Therefore, the second star, with a blueshift of 20 nm, is moving faster than the object in question 2, which had a redshift of 15 nm.

Learn more about the Doppler effect: https://brainly.com/question/28106478

#SPJ11

A 60Co source is labeled 4.35 mCi, but its present activity is found to be 2.0x107 Bq. (a) What is the present activity in mCi? mCi. (b) How long ago in years did it actually have a 4.00-mCi activity? years.

Answers

(a) The present activity of the 60Co source is approximately 0.054 mCi.

(b) The 60Co source had a 4.00-mCi activity approximately 39.20 years ago.

(a) To convert the present activity from becquerels (Bq) to millicuries (mCi), we'll use the conversion factor:

1 mCi = 3.7 × 10[tex]^10[/tex] Bq

Present activity in mCi = (2.0 × 10[tex]^7[/tex] Bq) / (3.7 × 10[tex]^10[/tex]Bq/mCi)

Present activity in mCi ≈ 0.054 mCi

Therefore, the present activity of the 60Co source is approximately 0.054 mCi.

(b) To calculate the time elapsed in years, we can use the concept of half-life. The half-life of 60Co is approximately 5.27 years.

We can use the formula:

t = (ln(N₀/N))/(λ)

where:

t = time elapsed

N₀ = initial activity (4.00 mCi)

N = present activity (0.054 mCi)

λ = decay constant (ln(2)/half-life)

Substituting the values:

t = (ln(4.00/0.054))/(ln(2)/5.27)

t ≈ 39.20 years

Therefore, the 60Co source had a 4.00-mCi activity approximately 39.20 years ago.

Learn more about present activity

brainly.com/question/32229851

#SPJ11

Find out how the experimental data provided for the energy
spectrum of the turbulent flows. Write a report to explain the
energy spectrum curves and measurement methods

Answers

Energy spectrum of turbulent flows refers to the process of showing the energy distribution of turbulent fluctuations in a fluid flow. It is a widely studied and critical topic in fluid mechanics.

There is a high level of variation in energy spectra among different types of turbulent flows, but there are a few general characteristics.The spectrum curve, also known as the spectrum density, of turbulent flows is usually represented in a logarithmic plot of energy versus frequency (wavenumber). It illustrates how much energy is carried by the different frequencies of the flow.

The slope of the energy spectrum, which is the negative derivative of the spectrum curve, is used to characterize the degree of turbulence. For instance, a shallower slope represents a more turbulent flow while a steeper slope indicates a smoother flow.

There are a few different methods used to measure energy spectra in turbulent flows, including hot-wire anemometry, laser Doppler velocimetry, and particle image velocimetry. Hot-wire anemometry is a widely used and well-established method that works by measuring the electrical resistance of a hot wire as it is cooled by the fluid flow.

Laser Doppler velocimetry is another technique that uses laser light to measure fluid flow velocity by measuring the Doppler shift of scattered light. Particle image velocimetry is a relatively new method that works by measuring the displacement of small tracer particles in the flow using high-speed cameras.

To know more about Energy spectrum, refer

https://brainly.com/question/23423065

#SPJ11

The following impedances are connected in series across a 50V, 18 kHz supply:
i. A 12 Ω resistor,
ii. A coil with a resistance of 2Ω and inductance of 150 µH.

a. Draw the circuit diagram,
b. Draw the phasor diagram and calculate the current flowing through the circuit,
c. Calculate the phase angle between the supply voltage and the current,
d. Calculate the voltage drop across the resistor,
e. Draw the phasor diagram and calculate the voltage drop across the coil and its phase angle with respect to the current.

Answers

Voltage in rectangular form = -6.6 + 40.1j

b. Phasor diagram and current calculation:

At first, we need to find out the reactance of the coil,

Xᵣ.L= 150 µH

      = 150 × 10⁻⁶Hf

      =18 kHzω

      =2πfXᵣ

      = ωL

      = 2 × 3.14 × 18 × 10³ × 150 × 10⁻⁶Ω

      =16.9Ω

Applying Ohm's law in the circuit,

I = V/ZᵀZᵀ

 = R + jXᵣZᵀ

 = 12 + j16.9 |Zᵀ|

 = √(12² + 16.9²)

 = 20.8Ωθ

 = tan⁻¹(16.9/12)

 = 53.13⁰

I = 50/20.8 ∠ -53.13

 = 2.4 ∠ -53.13A (Current in polar form).

Current in rectangular form = I ∠ θI

                                              = 2.4(cos(-53.13) + jsin(-53.13))

                                              =1.2-j1.9

c. Phase angle,θ = tan⁻¹((Reactance)/(Resistance))

θ = tan⁻¹((16.9)/(12))

θ = 53.13⁰

d. Voltage drop across resistor= IR

                                                   = (2.4)(12)

                                                   = 28.8 V

e. Phasor diagram and voltage across the coil calculation:

Applying Ohm's law,

V = IZᵢZᵢ

  = R + jXᵢZᵢ

  = 2 + j16.9 |Zᵢ|

  = √(2² + 16.9²)

  = 17Ω

θ = tan⁻¹(16.9/2)

  = 83.35⁰

Vᵢ = IZᵢ

Vᵢ = 2.4(17)

   = 40.8 V (Voltage in polar form)

Voltage in rectangular form = V ∠ θV

                                              = 40.8(cos(83.35) + jsin(83.35))

                                              = -6.6 + 40.1j

Learn more about Voltage from the given link

https://brainly.com/question/1176850

#SPJ11

"


48 In Fig. 5-35, three blocks are pulled to the right on a horizontal frictionless table by a force of magnitude T3 = 95.0 N. If m₁ = 10.0 kg, m₂ = 14.0 kg, and m3 = 23.0 kg, calculate (a) the mag
"

Answers

In the given problem, three blocks are pulled towards the right on a frictionless horizontal table with a force of magnitude T3 = 95 N. The tension T1 in the string between m₁ and m₂ is 9.9 N, and the tension T2 in the string between m₂ and m₃ is 8.8 N.

The masses of the three blocks are m₁ = 10 kg, m₂ = 14 kg, and m₃ = 23 kg. We need to find (a) the magnitude of the acceleration of the system, (b) the tension T1 in the string between m₁ and m₂, and (c) the tension T2 in the string between m₂ and m₃. We can apply Newton's second law of motion to find the acceleration of the system.

Substituting T3 = 95 N,

m₁ = 10 kg,

m₂ = 14 kg,

and m₃ = 23 kg in equations (1), (2), and (3):

T1 - 95 = 10aa

= (T1 - 95) / 10 ...(4)T2 - T1

= 14aT2 - T1 = 14(T1 - 95) / 10T2

= 1.4T1 - 133 ...(5)T3 - T2 = 23a95 - T2 = 23(T1 - 95) / 10Substituting equation (5) in equation (3):

95 - 23(T1 - 95) / 10 = 23(T1 - 95) / 10239.5 = 4.6T1T1 = 53.4 N ...(6)

Substituting equation (6) in equation (5):T2 = 1.4 × 53.4 - 133T2 = 8.80 N ...(7)

Substituting equation (4) in equations (1), (2), and (3):

a = (53.4 - 95) / 10a = -4.66 m/s²

T1 - 95 = 10 × (-4.66)T1 = 9.9 NT2 - T1 = 14 × (-4.66)T2 = 8.8 N

To know more about magnitude visit:

https://brainly.com/question/31022175

#SPJ11

1. The specific heat of ice is a = 2.09 * 10 ^ 3 * l / k * gl The specific heat of water is c_{w} = 4.19 * 10 ^ 3 * l / k * gl and its heat of fusion L_{f} = 3.33 * 10 ^ 3 1/kg The melting point of water is T_{m} = 273K Consider a 0.118 kg block of ice at 263 K. It is placed in a 0.815 kg bath of water initially at 288 K and perfectly isolated.
(a)How much heat is required to raise the temperature of the ice from 261 K to its melting point?
(b) If this heat is taken from the bath of water what will the new water temperature be?
(c) How much heat is required to melt the ice with its temperature at its melting point?
(d) If the heat required to melt the ice is again taken from the bath of water what will the new water temperature be?
(e)What is the final temperature of the combined water at thermal equilibrium?

Answers

(a) The heat required to raise the temperature of the ice from 261 K to its melting point is 1.97 kJ.

(b) If this heat is taken from the bath of water, the new water temperature will be 287.82 K.

(c) The heat required to melt the ice with its temperature at its melting point is 391.94 kJ.

(d) If the heat required to melt the ice is taken from the bath of water, the new water temperature will be 277.41 K.

(e) The final temperature of the combined water at thermal equilibrium is 277.41 K.

(a) To calculate the heat required to raise the temperature of the ice, we use the formula Q = mcΔT, where Q is the heat, m is the mass, c is the specific heat, and ΔT is the temperature change. Plugging in the values, we get Q = (0.118 kg) * (2.09 * 10^3 J/kg·K) * (273 K - 261 K) = 1.97 kJ.

(b) Since the heat taken from the bath of water is equal to the heat gained by the ice, we can use the formula Q = mcΔT to find the new water temperature. Rearranging the formula, we have ΔT = Q / (mc), and plugging in the values, we get ΔT = (1.97 kJ) / (0.815 kg * 4.19 * 10^3 J/kg·K) ≈ 0.64 K. Subtracting this temperature change from the initial temperature of the water, we get the new water temperature of 288 K - 0.64 K ≈ 287.82 K.

(c) The heat required to melt the ice at its melting point is given by Q = mLf, where Q is the heat, m is the mass, and Lf is the heat of fusion. Plugging in the values, we get Q = (0.118 kg) * (3.33 * 10^3 J/kg) = 391.94 kJ.

(d) Using the same principle as in (b), we can find the new water temperature by using the formula ΔT = Q / (mc). Plugging in the values, we get ΔT = (391.94 kJ) / (0.815 kg * 4.19 * 10^3 J/kg·K) ≈ 0.12 K. Subtracting this temperature change from the initial temperature of the water, we get the new water temperature of 288 K - 0.12 K ≈ 287.88 K.

(e) At thermal equilibrium, the final temperature of the combined water will be the same. Therefore, the final temperature of the combined water is 287.88 K.

For more questions like Temperature click the link below:

https://brainly.com/question/7510619

#SPJ11

A singly charged positive ion moving at 4.60 x 105 m/s leaves a circular track of radius 7.94 mm along a direction perpendicular to the 1.80 T magnetic field of a bubble chamber. Compute the mass (in atomic mass units) of this ion, and, from that value, identify it. .
2
4

He
+

1
1

H
+
3
2

He
+

1
2

H
+

Answers

We identify the particle whose mass is 182.70 amu to be 4He²⁺. We have to compute the mass (in atomic mass units) of the ion. We shall use the following formula to solve the problem: mv²r = q B

We are given the following data: Speed of the singly charged positive ion = v = 4.60 x 10⁵ m/s, Radius of the circular track along which the ion travels = r = 7.94 mm = 7.94 x 10⁻³ m, Magnetic field = B = 1.80 T

We have to compute the mass (in atomic mass units) of the ion. We shall use the following formula to solve the problem: mv²r=qB

From the given data, we know the value of qBmv²r=qBmv²r

= qB

Because the particle is positively charged, we have q = +1.6 x 10⁻¹⁹ C

Substituting the values, we get

m(4.60 x 10⁵)2(7.94 x 10⁻³)= (1.6 x 10⁻¹⁹)(1.80)m = (1.6 x 10-19)(1.80)(7.94 x 10⁻³)(4.60 x 10⁵)2m

= 3.038 x 10⁻²² kg

We can now compute the mass of the ion in atomic mass units.1 atomic mass unit (amu) = 1.661 x 10⁻²⁷ kg

Therefore, the mass of the ion is: m = (3.038 x 10⁻²²)/(1.661 x 10⁻²⁷)

= 182.70 amu

We identify the particle whose mass is 182.70 amu to be 4He²⁺.

Hence, the answer is: 4He²⁺.

To know more about atomic mass units, refer

https://brainly.com/question/29793336

#SPJ11

If a scale shows that an individual has a mass of 68 kg, what is that individual's weight? (Show work and explain)

a. 68 kg
b. -667 N
c. either a or b
d. neither a nor b

Answers

The individual's weight is approximately 666.4 N. the individual's weight is 68 kg.

To determine the individual's weight, we need to use the formula:

Weight = mass × gravitational acceleration

The gravitational acceleration on Earth is approximately 9.8 m/s².

(a) Using the given mass of 68 kg:

Weight = 68 kg × 9.8 m/s² = 666.4 N

So, the individual's weight is approximately 666.4 N.

(b) -667 N is not a valid weight value in this case because weight is a scalar quantity and is always positive. Therefore, option (b) is incorrect.

(c) The correct answer is (a) 68 kg since weight is a measure of the force exerted on an object due to gravity, and it is equivalent to the product of mass and gravitational acceleration.

Therefore, the individual's weight is 68 kg.

Learn more about acceleration here:

https://brainly.com/question/2303856

#SPJ11

Using filters, a photographer has created a beam of light consisting of three wavelengths: 400 nm (violet), 500 nm (green), and 650 nm (red). He aims the beam so that it passes through air and then enters a block of crown glass. The beam enters the glass at an incidence angle of θ1 = 26.6°.

The glass block has the following indices of refraction for the respective wavelengths in the light beam.

wavelength (nm) 400 500 650
index of refraction
n400 nm = 1.53

n500 nm = 1.52

n650 nm = 1.51

(a) Upon entering the glass, are all three wavelengths refracted equally, or is one bent more than the others?

400 nm light is bent the most

500 nm light is bent the most

650 nm light is bent the most

all colors are refracted alike

(b)What are the respective angles of refraction (in degrees) for the three wavelengths? (Enter each value to at least two decimal places.)

(i) θ400 nm



(ii)θ500 nm



(iii)θ650 nm

Answers

400 nm light is bent the most. Upon entering the glass, all three wavelengths are not refracted equally.the violet light than for the green or red light. The angle of refraction decreases with increasing wavelength, and the 650 nm light bends the least, while the 400 nm light bends the most.

This indicates that the velocity of the light decreases more when passing from air to glass for violet light than for green or red light. Since the velocity of the light is less in glass than in air, the light is refracted or bent towards the normal to the boundary surface.

(b) The angle of incidence is θ1 = 26.6° and the indices of refraction are as follows;n400 nm = 1.53n500 nm = 1.52n650 nm = 1.51The angle of refraction for each color can be determined using Snell's law;n1sinθ1 = n2sinθ2(i) θ400 nm= 16.36°(ii) θ500 nm= 16.05°(iii) θ650 nm= 15.72°

To know more about wavelengths visit:

https://brainly.com/question/31143857

#SPJ11

what type of meter contains its own separate power source

Answers

A digital multimeter (DMM) is a type of meter that contains its own separate power source, such as a battery. This makes it portable and independent of external power supplies.

In the field of physics, meters are used to measure various quantities. Some meters require an external power source, while others have their own separate power source. One such type of meter is the digital multimeter (DMM).

A digital multimeter is an electronic measuring instrument that combines several measurement functions in one unit. It is commonly used to measure voltage, current, and resistance. What sets digital multimeters apart is that they often have their own built-in power source, such as a battery. This allows them to be portable and independent of external power supplies.

Having a separate power source is advantageous as it makes the digital multimeter more versatile and convenient to use. Users can easily carry it around and use it in various locations without the need for an external power supply. The built-in power source ensures that the meter is always ready for use, regardless of the availability of external power.

Learn more:

About meter here:

https://brainly.com/question/32148796

#SPJ11

Using the component method, calculate the resultant (sum) of the following two vectors.
v

1

=175 m/s,70

polar (positive)
v

4

=200 m/s,200

polar (positive)

Calculate the components for r
v

1

Using the component method, calculate the resultant (sum) of the following two vectors.
v

1

=175 m/s,70

polar (positive)
v

2

=200 m/s,200

polar (positive)

Calculate the components for
v

2

Using the component method, calculate the resultant (sum) of the following two vectors.
v

1

=175 m/s,70

polar (positive)
v

2

=200 m/s,200

polar (positive)

Add the components of the resultant vector Using the component method, calculate the resultant (sum) of the following two vectors.
v

1

=175 m/s,70

polar (positive)
v

2

=200 m/s,200

polar (positive)

Calculate the resultant magnitude using the Pythagorean theorem. Using the component method, calculate the resultant (sum) of the following two vectors.
v

1

=175 m/s,70

polar (positive)
v

2

=200 m/s,200

polar (positive) Calculate the resultant direction using the tangent function. Express the direction in terms of the polar (positive) specification.

Answers

The components of v1​ are 165.3 m. Component of v2​ -68.3 m. The components of the resultant vector r are 97.0m. The resultant vector is 111.2 m/s at an angle of 59.9 degrees below the positive direction of the polar axis.

Components of v1​:

Since v1​ is 175 m/s at 70 degrees in the positive direction of the polar axis, its components in the x and y directions are:

x component: v1x​=175

cos 70° = 56.5

my component:

v1y​=175 sin 70° = 165.3 m

Component of v2​:

Since v2​ is 200 m/s at 200 degrees in the positive direction of the polar axis, its components in the x and y directions are:

x component: v2x​=200

cos 200° = -112.7

my component:

v2y​=200 sin 200° = -68.3 m

Addition of v1​ and v2​:

The components of the resultant vector r are:

r​x=v1​x+v2​x=56.5−112.7

=-56.2mr​y

=v1​y+v2​y

=165.3−68.3

=97.0m

Magnitude of resultant vector:

The magnitude of the resultant vector r is:

|r| = √(r​x² + r​y²)=√((-56.2)² + 97.0²)=111.2m

The direction of the resultant vector:

The direction of the resultant vector r is given by:

tan θ = r​y / r​x​= -97.0 / 56.2​=-1.727​θ = tan-1(-1.727) = -59.9°

Therefore, the resultant vector is 111.2 m/s at an angle of 59.9 degrees below the positive direction of the polar axis.

To know more about vectors please refer to the:

https://brainly.com/question/27854247

#SPJ11

Explain why the deformation of the water well screen in the photograph occurs.

Answers

The deformation of the water well screen in the photograph occurs due to several reasons such as the stress caused by water pressure is considered a primary factor, the quality of the well screen and its installation determine its durability, and environmental factors like soil composition,

Water flows into the well with a specific pressure that exerts stress on the well's screen, and the rate of water flow is directly proportional to the water pressure. The well screen is usually designed to withstand such pressure and last for a long time. If the well screen is poorly constructed or installed, it is more likely to deform due to various factors, including water pressure. Moreover, some well screens may be of poor quality or made from low-quality materials, making them susceptible to deformation.

Environmental factors like soil composition, temperature, and the acidity of water may cause the well screen to deform over time. Soil composition plays a significant role in the durability of the well screen because it can corrode or erode it. Water with a high acidity level can also corrode the well screen, leading to its deformation. In conclusion, several factors, such as water pressure, installation quality, and environmental factors, contribute to the deformation of the water well screen.

Learn more about water flows at:

https://brainly.com/question/10284232

#SPJ11

There is a 50-km, 220-5V, 60-Hz, three-phase overhead transmission line. The line has a per-phase resistance of 0.152/km, a per-phase inductance of 1.3263 mH/km. Shunt capacitance is neglected. Use the appropriate line model. The line is supplying a three-phase load of 381 MVA at 0.8 power factor lagging and at 220 kV. Find the series impedance per phase.

Answers

The series impedance per phase of the given transmission line is approximately 7,600 Ω (resistance) + j66.315 Ω (reactance).

The series impedance per phase of the given transmission line, we can calculate the total impedance using the per-phase resistance and inductance.

The total impedance (Z) per phase of the transmission line can be calculated using the following formula:

Z = R + jX

where R is the resistance and X is the reactance.

Length of the line (L) = 50 km

Resistance per phase (R) = 0.152 Ω/km

Inductance per phase (L) = 1.3263 mH/km

First, we need to convert the length and inductance units to consistent units:

Length in meters (L) = 50 km × 1000 m/km = 50,000 m

Inductance in ohms (X) = (1.3263 mH/km) × (50,000 m/km) × (1 H/1000 mH) = 66.315 Ω

Therefore, the series impedance per phase can be calculated as:

Z = 0.152 Ω/km × 50,000 m + j(66.315 Ω)

Z = 7,600 Ω + j(66.315 Ω)

Hence, the series impedance per phase of the transmission line is 7,600 Ω + j(66.315 Ω).

To know more about impedance,

https://brainly.com/question/30887212#

#SPJ11

[20 Points] Four very long straight wires located on the corners of a rectangle of width a=2[ m] and length b=10[ m]. Point A is located at the center of the rectangle, as shown in the figure. - Wire-1 is carrying a current I
1

=3 [A] directed into the page. - Wire-2 is carrying a current I
2

=10 [A] directed into the page. - Wire-3 is carrying a current I
3

=4[ A] directed out of the page. - Wire-4 is carrying a current I
4

=7[ A] directed out of the page. a) [4 Points] Find the magnetic field vector created by wire-1 at point A.
B
1



=∣
i
^
+∣∣
j
^

[T] b) [4 Points] Find the magnetic field vector created by wire-2 at point A.
B
2



=∣
i
^
+∣
j
^

[T] c) [4 Points] Find the magnetic field vector created by wire-3 at point A.
B
3



=∣
i
^
+ d) [4 Points] Find the magnetic field vector created by wire-4 at point A.
B

4

=∣
i
^
+∣
j
^

[T] e) [4 Points] Find the net magnetic field vector created by the 4 wires at point A.
B
net



=
i
^
+
j
^

[T]

Answers

Magnetic field vector (B) created by wire-4 at point A is 9.34 × 10^-9 i + 0 j T.(e) Net magnetic field(B net) vector created by the 4 wires at point A is; B net = B1 + B2 + B3 + B4Putting the calculated values, we get; B net = 0 + 4.02 × 10^-9 j + 1.34 × 10^-8 i + (-5.36 × 10^-9) i + 9.34 × 10^-9 i + 0 j T. On simplifying, we get; B net = 1.81 × 10^-8 i + 4.02 × 10^-9 j T. Therefore, the net B created by the 4 wires at point A is 1.81 × 10^-8 i + 4.02 × 10^-9 j T.

Given, The four very long straight wires are located on the corners of a rectangle of width (a)=2[m] and length (b)=10[m]. Point A is located at the center of the rectangle as shown in the figure. Wire-1 is carrying a current I1=3[Ampere(A)] directed into the page. Wire-2 is carrying a current I2=10[A] directed into the page. Wire-3 is carrying a current I3=4[A] directed out of the page. Wire-4 is carrying a current I4=7[A] directed out of the page.(a) Magnetic field vector created by wire-1 at point A is given as; B1=μ0I1/(4πr1) * sin90° From the right-hand rule(RHR), the magnetic field vector is along the positive i direction so it will be written as;B1 = 0 + (μ0I1/(4πr1) * 1) j . Here, r1 is the distance between wire-1 and point A which is (a^2+b^2)^0.5/2.Magnetic field at point A due to wire-1 is given as;B1 = 0 + (μ0I1/(4π(a^2+b^2)^0.5/2)) j. Putting the given values, we get;B1 = 0 + (4π × 10^-7 × 3/(4π(10^2+2^2)^0.5/2)) jB1 = 4.02 x 10^-9 j T.

Therefore, magnetic field vector created by wire-1 at point A is 0 + 4.02 x 10^-9 j T.(b) Magnetic field vector created by wire-2 at point A is given as;B2=μ0I2/(4πr2) * sin90°From the right-hand rule, the magnetic field vector is along the positive i direction so it will be written as; B2 = μ0I2/(4πr2) * (-1) j. Here, r2 is the distance between wire-2 and point A which is (a^2+b^2)^0.5/2. Magnetic field at point A due to wire-2 is given as; B2 = μ0I2/(4π(a^2+b^2)^0.5/2) * (-1) j. Putting the given values, we get;B2 = 4π × 10^-7 × 10/(4π(10^2+2^2)^0.5/2) * (-1) jB2 = -1.34 × 10^-8 j T. Therefore, magnetic field vector created by wire-2 at point A is 1.34 x 10^-8 i + 0 j T.(c) Magnetic field vector created by wire-3 at point A is given as; B3=μ0I3/(4πr3) * sin90° From the RHR, the magnetic field vector is along the negative j direction so it will be written as;B3 = μ0I3/(4πr3) * (-1) i. Here, r3 is the distance between wire-3 and point A which is (a^2+b^2)^0.5/2. Magnetic field at point A due to wire-3 is given as;B3 = μ0I3/(4π(a^2+b^2)^0.5/2) * (-1) i. Putting the given values, we get;B3 = 4π × 10^-7 × 4/(4π(10^2+2^2)^0.5/2) * (-1) iB3 = -5.36 × 10^-9 i T.

Therefore, magnetic field vector created by wire-3 at point A is -5.36 × 10^-9 i + 0 j T.(d) Magnetic field vector created by wire-4 at point A is given as;B4=μ0I4/(4πr4) * sin90° From the RHR, the magnetic field vector is along the positive j direction so it will be written as; B4 = μ0I4/(4πr4) * 1 i. Here, r4 is the distance between wire-4 and point A which is (a^2+b^2)^0.5/2. Magnetic field at point A due to wire-4 is given as;B4 = μ0I4/(4π(a^2+b^2)^0.5/2) * 1 i. Putting the given values, we get; B4 = 4π × 10^-7 × 7/(4π(10^2+2^2)^0.5/2) * 1 iB4 = 9.34 × 10^-9 i T.

To know more about right hand rule visit:

https://brainly.com/question/14434299

#SPJ11

1. How can you determine the terminal velocity at hindered gravitational settling in the zone settling regime of a solid particle in the fluid phase? What is hindered settling and the opposite of that? What can you say about the drag coefficient in these cases?

Answers

Terminal velocity at hindered gravitational settling in the zone settling regime of a solid particle in the fluid phase can be determined as follows: For hindered settling, there is an extensive inter-particle interaction that hinders the settling velocity of solid particles in fluid.

Hindered settling occurs at relatively high solids loading conditions. The hindered settling is the opposite of the ideal settling, which occurs under low solids loading conditions. Hindered settling can be further broken down into three categories, depending on the extent of hinderance they experience. The categories are "Z" factor, "F" factor, and "Q" factor.

For all three categories, the particles' settling speed decreases as the solids loading increases.For a particle that is settling through a fluid, the drag coefficient refers to the resistance it encounters from the fluid. The fluid's properties, such as its viscosity, density, and velocity, all have an impact on the drag coefficient. The drag coefficient is larger in cases where the particle is large and the fluid is viscous.

To know more about Terminal velocity , refer

https://brainly.com/question/30466634

#SPJ11

A proton travels along the x-axis through an electric potential V=(250 V/m)x. Its speed is 3.5×10 5
m/s, as it passes the origin, moving in What is the proton's speed at x=1.0 m ? the +x-direction. Express your answer with the appropriate units.

Answers

The proton's speed at x = 1.0 m is approximately 3.499 × 10⁵ m/s. This is based on the given electric potential V = (250 V/m)x and the initial speed of the proton at the origin of 3.5 × 10⁵ m/s.

The electric potential is given by V = (250 V/m)x, which means the electric potential increases linearly with x along the x-axis. Since the proton is moving in the +x-direction, its potential energy (PE) is decreasing as it moves away from the origin.

The change in potential energy (ΔPE) can be calculated by multiplying the electric potential (V) by the displacement (Δx) from the origin to x = 1.0 m:

ΔPE = V * Δx

Δx = 1.0 m (given)

Substituting the given electric potential:

ΔPE = (250 V/m) * (1.0 m)

ΔPE = 250 V

The change in potential energy (ΔPE) is equal to the change in kinetic energy (ΔKE) for a conservative force field.

Therefore, we can equate the change in potential energy to the change in kinetic energy:

ΔKE = ΔPE

The change in kinetic energy (ΔKE) is given by:

ΔKE = (1/2) * m * (v² - u²)

Where m is the mass of the proton, v is the final speed at x = 1.0 m, and u is the initial speed at the origin (3.5 × 10⁵ m/s).

Substituting the values:

ΔKE = (1/2) * m * (v² - (3.5 × 10⁵ m/s)²)

Since the proton is positively charged, its potential energy is decreasing, which means its kinetic energy is increasing.

Therefore, the change in kinetic energy is positive, and we can write:

ΔKE = -ΔPE

Substituting the values:

(1/2) * m * (v² - (3.5 × 10⁵ m/s)²) = -250 V

Simplifying the equation, we find:

(v² - (3.5 × 10⁵ m/s)²) = -500 V / m * (2 / m)

(v² - (3.5 × 10⁵ m/s)²) = -1000 V / m

Now, to find the speed (v) at x = 1.0 m, we solve for v:

v² = (3.5 × 10⁵ m/s)² - 1000 V / m

v = √((3.5 × 10⁵ m/s)² - 1000 V / m)

Calculating the value, we find:

v ≈ 3.499 × 10⁵m/s

Therefore, the proton's speed at x = 1.0 m is approximately 3.499 × 10⁵ m/s.

To learn more about potential refer here:

https://brainly.com/question/31148592#

#SPJ11


Need ASAP. Please solve
correctly and show solutions if needed. Thankyou
Let \( \mathrm{R} \) be the region enclosed inside \( y=x^{2} \) and \( y=3 x-2 \) a. Sketch the region \( \mathrm{R} \). (5 points) b. Compute the area of the region R.(10 points)

Answers

To find the area of region R, we need to integrate the difference between the two functions along the given limits of x. ∫(upper limit) (lower limit) (y2 - y1) dx. The area of region R is (-1/6) sq. units.

A) The region enclosed inside y = x² and y = 3x - 2 is illustrated below: Region R

The graph is showing the region R above. We need to find the area of region R. To find the area of region R, we need to integrate the difference between the two functions along the given limits of x.

∫(upper limit) (lower limit) (y2 - y1) dx,

where y2 = 3x - 2, and y1 = x²

B) Now, let us compute the limits of x for which the functions intersect. To find these, we need to set

y1 = y2.x² = 3x - 2⇒ x² - 3x + 2 = 0⇒ (x - 1)(x - 2) = 0

Thus, the functions intersect at x = 1 and x = 2.

So, we integrate from x = 1 to x = 2.∫ (2, 1) (3x - 2 - x²)

dx= ∫(2, 1) (3x - x² - 2) dx= [3x²/2 - x³/3 - 2x]₂¹

= [3(2)²/2 - (2)³/3 - 2(2)] - [3(1)²/2 - (1)³/3 - 2(1)]

= [6 - (8/3) - 4] - [1/2 - 1/3 - 2]= (-1/6) sq. units

Therefore, the area of region R is (-1/6) sq. units.

To know more about functions refer to:

https://brainly.com/question/1533811

#SPJ11

A telecommunications line is modelled as a series RLC circuit with R = 1 Ohm/km. = 1 H/km and C= 1 F/km. The input is a 1V sinusoid at 1kHz. The output is the voltage across the capacitor. At what distance (to the nearest km) will the system have lost half its power. A telecommunications line is modelled as a series RLC circuit with R = 1 Ohm/km, L = 1 H/km and C = 1 F/km. The input is a 1V sinusoid of varying frequency. The output is the voltage across the capacitor and the line is of 100km length. At what frequency (to the nearest Hz) will the system have lost half its power.

Answers

Part 1:Power loss occurs due to resistance. The distance at which the system loses half of its power can be determined as follows: Let the distance be x km. The power loss will be P/2, where P is the power transmitted.

The RLC circuit is a low pass filter with the cut off frequency given by:f = 1/2π√LCHere,

L = 1 H/km,

C = 1 F/km and

f = 1 kHz

∴ 1 kHz = 1000 Hz

f = 1/2π√LC

= 1/2π√(1 × 10³ × 1 × 10⁻⁹)

= 1/2π × 1 × 10⁻³

= 159.15 Hz

P/2 = P(x)/100, where P(x) is the power transmitted at a distance of x km.

P = V²/R, we have

P/2 = (V²/R) (x)/100

Solving for x, we get x = 69.3 km (approx.)

The system will have lost half its power at a distance of 69 km (approx.).

Part 2: Using the same formula for cut-off frequency as in Part 1, we get f = 1/2π√LC = 1/2π√(1 × 10³ × 1 × 10⁻⁹) = 159.15 Hz The system will have lost half its power at a frequency of 159 Hz (approx.).

To know more about Power visit:

https://brainly.com/question/29575208

#SPJ11

A rectangular waveguide has dimensions a = 0.12 cm and b = 0.06 cm

a) Determine the first three TE modes of operation and their cutoff frequencies.

b) Write the expressions for the E, and E, electric field components when you are above the cutoff frequency for 2nd order mode and below the cutoff frequency for the 3rd order mode. Leave the answer in terms of unknown variables.

Answers

a) The cutoff frequency is the frequency above which the mode propagates in the waveguide. For a rectangular waveguide, the cutoff frequency is given by the formula

fco = c / 2√(a² + b²),

where c is the speed of light in free space.

Substituting the given values, we get:

fc1 = 3.29 GHz

fc2 = 9.87 GHz

fc3 = 19.83 GHz

The first three TE modes are:

TE101, with fc1 as the cutoff frequency

TE201, with fc2 as the cutoff frequency

TE301, with fc3 as the cutoff frequency

b) The expression for the E field components for the TE201 mode are:

Ez = E0 cos(πy/b) sin(πx/a)

Ey = 0Ex = 0

where E0 is the amplitude of the electric field, and x and y are the dimensions of the waveguide.

For a frequency above the cutoff frequency of the TE201 mode but below the cutoff frequency of the TE301 mode, the waveguide would support only the TE201 mode.

The expression for the E field components in this case would be:

Ez = E0 cos(πy/b) sin(πx/a)

Ey = 0Ex = 0

For a frequency below the cutoff frequency of the TE301 mode, the waveguide would not support any mode of operation.

Learn more about cutoff frequency from the given link

https://brainly.com/question/27986610

#SPJ11

0.IKB/Sill 3:40 PM (f) •76% Homework of Chapter 6 9. Single Choice As every amusement park fan knows, a Ferris. wheel is a ride consisting of seats mounted on a tall ring that rotates around a horizontal axis. When you ride in a Ferris wheel at constant speed, what are the directions of a FN your acceleration and the normal force on you (from the always upright seat) as you pass through (1) the highest point and (2) the lowest point of the ride? (3) How does the magnitude of the acceleration at the highest point compare with that at the lowest point? (4) How do the magnitudes of the normal force compare at those two points? A , (1) a downward, FN downward; (2) a and FN upward; (3) same; (4) greater at lowest point; , (1) a downward, FN upward; (2) a and FN upward; (3) same; (4) greater at lowest point; , (1) a downward, FN upward; (2) a and FN upward; (3) greater at lowest point; (4) तं

Answers

The highest point is a downward and the lowest point of the ride is FN upward, The magnitude of the acceleration at the highest point compare with that at the lowest point is the same, The magnitudes of the normal force compare at those two points is greater at the lowest point. The correct answer is option(a).

When the Ferris wheel is at the highest point, the direction of the normal force is down towards the center of the wheel and the direction of acceleration is down or towards the ground. The net force at this point is equal to the force of gravity acting downwards. So, the normal force is lesser than the weight of the person riding on the Ferris wheel.

On the other hand, when the Ferris wheel is at its lowest point, the direction of the normal force is upwards, and the direction of acceleration is also upwards. The net force at this point is equal to the weight of the person plus the force of gravity. Hence, the normal force is greater than the weight of the person.

To learn more about acceleration:

https://brainly.com/question/25876659

#SPJ11

1. If the centrifugal switch fails to open as a split-phase motor accelerates to its rated speed, what happens to the starting winding?

2. Describe one limitation of a capacitor-start, induction-run motor.

Answers

1. If the centrifugal switch fails to open as a split-phase motor accelerates to its rated speed, the starting winding will continue to be energized. This results in overheating of the winding and can cause damage to the motor. This is because the starting winding is designed to be used only during the starting process, and not continuously.

If the centrifugal switch fails to open, it means that the starting winding will be in use for too long, causing overheating, which will damage the motor.

2. One limitation of a capacitor-start, induction-run motor is that it has low power factor. This is because the capacitor is designed to be used only during the starting process, and not during the running process. Therefore, during the running process, the motor will have a low power factor, which means that it will consume more energy from the power supply than is actually required. This results in wastage of energy and higher electricity bills. Additionally, the motor may not be suitable for use in applications where high power factor is required, such as in industrial processes that require high efficiency and low energy consumption.

To learn more about motor visit;

https://brainly.com/question/31214955

#SPJ11

A thin hoop of negligible width is rolling on a horizontal surface at speed v=3.6 m/s when it reaches a 17

incline. How far up the incline will it go? Express your answer using three significant figures and include the ap, Part B How long will it be on the incline before it arrives back at the bottom? Express your answer using three significant figures and include the apprc

Answers

1). The hoop will go up the incline approximately 0.656 m when rolling with a speed of 3.6 m/s. 2). It will take approximately 0.322 s for the hoop to arrive back at the bottom of the incline.

To determine how far up the incline the hoop will go, we can analyze the energy conservation in the system. When the hoop reaches the incline, its initial kinetic energy is converted into potential energy as it moves up the incline. The total mechanical energy of the system is conserved, neglecting any energy losses due to friction.

Initial speed, v = 3.6 m/s

Incline angle, θ = 17°

The height the hoop will reach on the incline, we need to equate the initial kinetic energy to the potential energy at the highest point:

1/2 * I * ω² = m * g * h

The moment of inertia (I) for a thin hoop of mass m and radius r is I = m * r².

The linear velocity v of the hoop is related to the angular velocity ω by v = r * ω.

Plugging these values into the equation, we have:

1/2 * m * r² * (v / r)² = m * g * h

Simplifying the equation, we get:

1/2 * v² = g * h

Solving for h, we have:

h = (1/2 * v²) / g

Substituting the given values:

h = (1/2 * 3.6²) / g

The acceleration due to gravity, g, is approximately 9.8 m/s².

h = (1/2 * 3.6²) / 9.8

Calculating the value, we find:

h ≈ 0.656 m (rounded to three significant figures)

Therefore, the hoop will go up the incline approximately 0.656 m.

Now, let's move on to Part B, which asks for the time it takes for the hoop to arrive back at the bottom of the incline.

We can find the time using the kinematic equation:

s = ut + (1/2)at²

where:

s = displacement (height of the incline)

u = initial velocity (0 since the hoop starts from rest at the top)

a = acceleration (due to gravity, -9.8 m/s²)

t = time

Rearranging the equation, we have:

t = [tex]\sqrt{(2s)/a}[/tex]

Substituting the known values:

t = sqrt([tex]\sqrt{(2 * 0.656) / 9.8}[/tex])

Calculating the value, we find:

t ≈ 0.322 s (rounded to three significant figures)

Therefore, the hoop will take approximately 0.322 s to arrive back at the bottom of the incline.

To learn more about speed refer here:

https://brainly.com/question/17661499#

#SPJ11

Problem 3: An otter is swimming in the deep area of his tank at the zoo. The surface area of the otter's back is A = 0.45 m2, and you may assume that his back is essentially flat. The gauge pressure of the water at the depth of the otter is P = 10500 Pa.

Part (a) Enter an expression for the magnitude of the force F on the back of the otter in terms of the gauge pressure P and the atmospheric pressure P0.

Part (b) Solve for the magnitude of the force F, in newtons.

Part (c) The direction of the force F is always ________ to the surface the water is in contact with (in this case, the back of the otter).

Answers

P = 10500 PaP0 is the atmospheric pressure. he given values in the above equation to find the magnitude of the force is -43290 N. The direction of the force F is normal (perpendicular) to the surface of the water, which is in contact with the back of the otter.

Part (a) Magnitude of the force F on the back of the otter can be defined as follows:

F = (P - P0)A

Where, P = 10500 PaP0 is the atmospheric pressure

Part (b) Substitute the given values in the above equation to find the magnitude of the force F,F = (10500 - 101300) × 0.45 F = -43290 N

Part (c) The direction of the force F is always perpendicular to the surface the water is in contact with (in this case, the back of the otter).

Therefore, the direction of the force F is normal (perpendicular) to the surface of the water, which is in contact with the back of the otter.

An otter is swimming in the deep area of his tank at the zoo. The surface area of the otter's back is A = 0.45 m², and you may assume that his back is essentially flat. The gauge pressure of the water at the depth of the otter is P = 10500 Pa. The expression for the magnitude of the force F on the back of the otter is F = (P - P0)A. The magnitude of the force F, in newtons, is -43290 N. The direction of the force F is always perpendicular to the surface the water is in contact with (in this case, the back of the otter).

To know more about atmospheric pressure refer to:

https://brainly.com/question/29713163

#SPJ11

What are the peak (maximum) values of the voltages across the loads (resistor and DC voltage source) in each circuit topology? Assume that the diodes in the circuits are not ideal and each have a cons

Answers

In electrical circuits, voltage is a measure of electric potential energy per unit charge. When the electrical current passes through a load (a resistor), a voltage drop occurs. Furthermore, a voltage source (a DC voltage source) produces a potential difference that creates an electric current flow in the circuit.

Topologies are a series of arrangements of electrical components that operate together to achieve a specific goal. The voltage drop across the load and the voltage produced by the voltage source may be used to estimate the peak voltage values across the loads in a circuit topology.In Circuit 1, the maximum voltage that can be seen across the load and DC voltage source is VCC - VD,

where VCC is the voltage produced by the voltage source and VD is the voltage drop across the diode. As a result, the peak voltage for the resistor and voltage source in Circuit 1 is given by VCC - VD = 15 - 0.7 = 14.3V.In Circuit 2, the maximum voltage that can be seen across the load and DC voltage source is VD. In a forward-biased diode, the voltage drop is usually around 0.7V.

As a result, the peak voltage for the resistor and voltage source in Circuit 2 is given by VD = 0.7V.The voltage drop across the diode causes a loss of energy in both circuit topologies. As a result, the peak voltages that may be measured across the loads will be lower than the voltage produced by the voltage source. As a result, circuit designers try to use diodes with the lowest possible voltage drops to minimize energy loss.

To know more about voltage visit:

https://brainly.com/question/32002804

#SPJ11

A steady current of 590μA flows through the plane electrode separated by a distance of 0.55 cm when a voltage of 15.5kV is applied. Determine the first Townsend coefficient if a current of 60μA flows when the distance of separation is reduced to 0.15 cm and the field is kept constant at the previous value.

Answers

The first Townsend coefficient is approximately 0.3722.

Ionization energy refers to the amount of energy that's required to remove an electron from an atom that's isolated.

To determine the first Townsend coefficient, we can use the Townsend's ionization equation:

α = (I2 / I1) * (d1 / d2)

where:

α is the first Townsend coefficient

I1 is the initial current (590 μA)

I2 is the final current (60 μA)

d1 is the initial separation distance (0.55 cm)

d2 is the final separation distance (0.15 cm)

Plugging in the given values:

α = (60 μA / 590 μA) * (0.55 cm / 0.15 cm)

  ≈ 0.1017 * 3.6667

  ≈ 0.3722

Therefore, the first Townsend coefficient is approximately 0.3722.

Learn more about Townsend's ionization equation from:

https://brainly.com/question/15625295

#SPJ11

PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
Assignment: 1. Determine the internal normal force at section \( A \) if the rod is subjected to the external uniformally distributed loading along its length. 2. Determine the internal normal force o

Answers

1. Internal normal force at section A:Let's consider a rod subjected to a uniformly distributed load. We can see that the section will be in the state of the internal force if it is cut from this rod by the plane section at point A.The internal normal force of the rod can be determined by using the free body diagram as shown below:

Let the internal normal force at section A be N, and the external distributed load be w per unit length. Now, consider an infinitesimal section of the rod of length dx at a distance x from point A. The free body diagram of this section can be drawn as:Applying the equation of equilibrium in the vertical direction, we can get:N(x) − N(x+dx) − wdx = 0Since the rod is in a state of static equilibrium, the internal normal force must be constant throughout the length of the rod. Thus, we can write:N − N − wl = 0N = wl

Therefore, the internal normal force at section A is wL.2. Internal normal force of the rod:Let's consider a rod of length L subjected to a uniformly distributed load. We can find the internal normal force of the rod using the free body diagram as shown below:Let the internal normal force at the left end be N1 and that at the right end be N2. Now, consider an infinitesimal section of the rod of length dx at a distance x from the left end.

The free body diagram of this section can be drawn as:Applying the equation of equilibrium in the vertical direction, we can get:N(x) − N(x+dx) − wdx = 0Since the rod is in a state of static equilibrium, the internal normal force must be constant throughout the length of the rod. Thus, we can write:N1 − N2 = ∫₀ᴸwdxN1 − N2 = (wL²)/2Therefore, the internal normal force of the rod is (wL²)/2.

To know more about internal visit :

https://brainly.com/question/31799903

#SPJ11

A resistor of 10.0 M2 is in series with a capacitor of 4 yF, and a power source of 5 V. A switch in the circuit is open and the capacitor has no charge. At t=0, the switch is closed, completing the circuit and the capacitor begins to charge. Recall that vc(t) = Vsource ((1 - e^(-t/t)). a) What is the voltage across the capacitor at time zero? b) What is the significance of the time at which the voltage is 63% of the maximum voltage on the capacitor? c) Calculate the time constant for this circuit. d) What is the voltage across the capacitor at 15 s? e) How long will it take the capacitor to reach 4.5 V?

Answers

a) The voltage across the capacitor at time zero is zero. b) The significance of the time at which the voltage is 63% of the maximum voltage on the capacitor is that it is equal to the time constant of the circuit. c) The time constant for this circuit is given by the formula RC. d) vc(15 s) = 3.22 V. e) t = 92 s.

When the switch is open, there is no current flow in the circuit and the capacitor is uncharged. When the switch is closed, current begins to flow and the capacitor starts to charge. The voltage across the capacitor rises over time until it reaches its maximum value, which is equal to the voltage of the power source.

The time constant of the circuit determines how quickly the capacitor charges and how quickly the voltage across it rises to its maximum value. In this circuit, the time constant is 40 seconds.

To find the voltage across the capacitor at any time t, we use the formula for voltage across a charging capacitor:

vc(t) = Vsource((1 - e^(-t/RC)).

We can use this formula to find the voltage across the capacitor at 15 s, which is 3.22 V.

To find how long it will take the capacitor to reach a certain voltage, we set vc(t) equal to that voltage and solve for t.

In this case, it will take 92 s for the capacitor to reach 4.5 V.

Learn more about capacitor here:

https://brainly.com/question/31627158

#SPJ11

An ideal gas at 23.7°C and a pressure of 1.42×105 Pa occupies a volume of 2.08 m3. Let R = 8.314 J/K mol (a) How many moles of gas are present? Number: __________ mol (b) If the volume is raised to 3.79 m2 and the temperature raised to 37.1°C, what will be the pressure of the gas?

Answers

b)  the pressure of the gas after the change in volume and temperature will be approximately 1.31 × 105 Pa.

(a) To calculate the number of moles of gas present, we can use the ideal gas law equation:

PV = nRT

Where:

P = Pressure of the gas

V = Volume of the gas

n = Number of moles of the gas

R = Ideal gas constant

T = Temperature of the gas

Given:

Pressure (P) = 1.42 × 105 Pa

Volume (V) = 2.08 m³

Temperature (T) = 23.7°C = 23.7 + 273.15 = 296.85 K (converted to Kelvin)

Ideal gas constant (R) = 8.314 J/K mol

Now, let's solve for the number of moles (n):

n = PV / RT

n = (1.42 × 105 Pa * 2.08 m³) / (8.314 J/K mol * 296.85 K)

Calculating this value:

n ≈ 11.8 mol

Therefore, approximately 11.8 moles of gas are present.

(b) To find the pressure of the gas after the change in volume and temperature, we can use the ideal gas law equation again:

P1V1 / T1 = P2V2 / T2

Where:

P1 = Initial pressure

V1 = Initial volume

T1 = Initial temperature

P2 = Final pressure (to be determined)

V2 = Final volume

T2 = Final temperature

Given:

Initial pressure (P1) = 1.42 × 105 Pa

Initial volume (V1) = 2.08 m³

Initial temperature (T1) = 23.7°C = 23.7 + 273.15 = 296.85 K

Final volume (V2) = 3.79 m³

Final temperature (T2) = 37.1°C = 37.1 + 273.15 = 310.25 K

Now, let's solve for the final pressure (P2):

P2 = (P1 * V1 * T2) / (V2 * T1)

P2 = (1.42 × 105 Pa * 2.08 m³ * 310.25 K) / (3.79 m³ * 296.85 K)

Calculating this value:

P2 ≈ 1.31 × 105 Pa

To know more about pressure visit:

brainly.com/question/30673967

#SPJ11

Q1. A lawn sprinkler sprays water from an array of 12 holes, each 0.40 cm in diameter. The sprinkler is fed by a garden hose 3.5 cm in diameter, which is supplied by a tap. a) If the tap can supply 15 litres of water every minute, calculate the speed at which water moves through the garden hose. (4) b) Calculate the velocity with which the water leaves one hole in the sprinkler array. (4)

Answers

(a) The speed at which water moves through the garden hose is 25.97 cm/s. (b) The velocity with which the water leaves one hole in the sprinkler array is 2.57 m/s.

a) To calculate the speed at which water moves through the garden hose, we'll use the formula for the volume rate of flow, which is given by

Q = A×v, where A is the cross-sectional area of the hose and v is the velocity of the water. We have the diameter of the hose, which we'll use to find its radius.

r = d/2 = 3.5/2 = 1.75 cmA = πr² = π(1.75)² = 9.625 cm²

To convert the flow rate from L/min to cm³/s, we'll multiply by 1000/60, because 1 L = 1000 cm³ and 1 min = 60 s.Q = 15 × 1000/60 = 250 cm³/s

Q = A × v ⇒ v = Q/A

= 250/9.625

= 25.97 cm/s

(b)The velocity with which the water leaves one hole in the sprinkler array can be found using Bernoulli's equation, which relates the pressure of the fluid to its velocity.

p1 + (1/2)ρv1² = p2 + (1/2)ρv2²

where p1 and v1 are the pressure and velocity of the water as it enters the sprinkler array, and p2 and v2 are the pressure and velocity of the water as it leaves the hole in the sprinkler.

We'll assume that the pressure remains constant throughout, so p1 = p2. Let's start by finding the velocity of the water as it enters the sprinkler array. Since the cross-sectional area of the hose is much larger than the combined areas of the holes in the sprinkler array, we can assume that the velocity of the water remains constant as it passes through the array. We'll use the equation of continuity to relate the velocity of the water in the hose to the velocity of the water in the sprinkler. A1v1 = A2v2

where A1 and v1 are the cross-sectional area and velocity of the hose, and A2 and v2 are the cross-sectional area and velocity of the water as it passes through one hole in the sprinkler.

We have already found

A1 and v1.v2 = A1v1/A2 = (9.625 × 25.97)/(12 × (0.4/2)² × π) = 2.57 m/s

The velocity of the water as it leaves the hole in the sprinkler is 2.57 m/s.

To know more about speed please refer:

https://brainly.com/question/13943409

#SPJ11

Other Questions
JnH Co Inc. is a U.S. energy company with operations in oil and gas exploration and development (E\&P) and refining and marketing (R\&M). The marginal tax rate (TC) is 40% and the market risk premium is 5%. The current 30 -year U.S. Treasury bond yield is 2.8%. The target consolidated debt-to-value ratio, set in consultation among division and corporate executives and the board, is 30% (this is the firm's target for the proportion of net debt to enterprise value). Use net debt in your calculations (instead of total debt) consistently throughout the entire problem! Use the following data in order to calculate the prevailing consolidated debt-to-value ratio in part (a) below: Derive an estimate of rE based on the target consolidated debt-to-value ratio using the CAPM and the formulas below: U = [1+(1T C )(D/E)]E E =[1+(1T C )(D/E)] U Use the 30 -year U.S. Treasury bond yield as rf. E=1.25 and it is based on the prevailing consolidated debt-to-value ratio. To determine an appropriate estimate of equity beta based on the target capital structure, unlever E=1.25 and then relever (reminder: use the formulas above). during the year Allison sold stock her cost basis and other details about the transactions were reported to her and to irs on form 1099b with no correction or adjustment how is this transaction reported ? A. the amount of her capital gain or deductible loss is reported directly on page 1 form 1040 B. The amount of her cap gain or loss is reported on schedule 1 thwn combined with her other sources of additional income before total is reported on page 1 form 1040 C. details of the transaction's must be reported on form 8949 the totals are then carried to schedule d finally the net amount of her cap gain is reported on page 1 of 1040 D. information about the transaction is reported directly on schedule d the amount of her cap gain is he reported on page 1 of her 1040 In your point of view, do you consider fashion, industrial design and furniture design art? Zowie is a six-year-old company that specializes in immediate (less than two hours) delivery of computer peripheral devices to consumers. The value-added in the service comes not only from the speed of delivery, but the delivery persons ability to install and troubleshoot the new device on any computer. Zowies earnings have grown at a rate of 35% per year, to a (just-announced) value this year of $2,000,000, or $2 per share.Recently, Zowie has experienced a slowdown in earnings, due to the fact that the supply of delivery people with a deep knowledge of computers is growing scarcer. Zowie does not anticipate that this situation will improve anytime soon; consequently, analysts have forecast that earnings for the next 3 years will grow at a slower rate. After that three-year period, it is forecast that the company will be mature and grow at a stable rate per year for the foreseeable future.Assume that the company does not begin paying dividends until the year that the growth rate (going forward) stabilizes (year 4), at which point dividend payout will be two-thirds of earnings. Zowie does not have debt currently, and has no plans to issue debt or equity. An appropriate discount rate for cash flows of Zowies risk is 14% per year.The growth rate estimates for the next three years range from a low of 10% per year to a high of 15% per year. The estimates for the mature or stable rate per year after that time ranges from a low of 3% per year to a high of 5% per yeaBased on the information given, assume that the 15% growth rate over the next three years is accurate. You observe that the current price of a share of Zowies stock is 50% larger than $15.97. Calculate the stable growth rate implied by this share price, assuming that the market shares your belief about the appropriate discount rate. (Note: a small rounding error is reasonable) Natural, open spaces often found in urban areas used for botanical gardens and/or absorbing excessive floodwaters after heavy rains is/are heat islands littoral zones greenbelts marginal lands The buildup of fatty plaques on the inside of arteries can cause them to narrow, restricting blood flow through them. Suppose that plaque decreases the radius of a section of artery by 25%. By what factor does the volume flow rate through that artery decrease, assuming the pressure drop across it is unchanged (which is a reasonable first guess, since there are physiological limits on how large a pressure the heart can exert by pumping), as are any other relevant parameters?Model the brachial artery (the one in the upper arm) as a tube of length 20 cm and radius 2 mm. Blood moves through the artery at an average speed of 9 cm/s, and the viscosity of blood is about 3.5 103 Pa s.What is the pressure difference between the two ends of the 20 cm artery?How does this compare to a typical human blood pressure of about 100 mm Hgmeasured at the brachial artery? Do viscous pressure drops introduce a significant difference between the pressure measured at the brachial artery and the pressure near the heart? Design and sketch circuits using Operational Amplifiers for thefollowing:A differentiator Vo=10 d(Vi)/dtWhere Vi is the input and Vo is the output Two charges, of +13 and -5 C, are separated by 190 mm. What is the potential at the midpoint A of a line joining the two charges? kv At what point B is the electric potential equal to zero? cm from the 13 C charge plasmapheresis is the removal of whole blood from the body, separation of its cellular elements, and reinfusion of these cellular elements suspended in saline or a plasma substitute. D5 NSS at 125 mL/hourControlled CHO diet as toleratedDiscontinue IV insulin.12 U NPH and 4 U regular insulin BID.CBGM ac and hs following standard sliding scale insulin therapyThe treatment plan is to use both short-acting insulin and NPH. Select the appropriate interventions you would implement related to insulin administration for I.G. 2) (5 points) It is claimed that some professional baseball players can see which way the ball is spinning as it travels toward home plate. One way to judge this claim is to estimate the distance at which a batter can first hope to resolve two points on opposite sides of a baseball which has a diameter of 0.0738 m. A) Estimate the angle and the distance, assuming that the pupil of the eye has a diameter of 2.0 mm, the material within the eye has a refractive index of 1.36, and the wavelength of the light is 550 nm. B) Considering the distance between the pitcher's mound and home plate is 18.4 m, can you rule out or verify the claim based on your answer in part A)? Which statement describes the chemical properties of the element Iodine?1-It's crystals are a metallic a gray2-It dissolves in alcohol3-It forms a violet colored gas4-It reacts with hydrogen to form a gas In the reaction below state what is being oxidized and what is being reduced.? 4 Fe + 3 O2 2 Fe2O3 Violating collaborative decisions is a main concern in Game Theory. What kind of punishment can be imposed and implemented? However, violations can go both ways causing global problems. What corrective actions and punishment can be designed and what is our role in the process? Let us consider the global gas crisis fueling inflation and the game theory's textbook example: OPEC. In Oct 3, 2018, Reuters reported the following:"Iran accused Saudi Arabia and Russia on Wednesday of breaking OPECs agreement on output cuts by producing more crude, adding that the two countries would not be able to produce enough oil to make up for a reduction in Iranian exports. Reuters reported on Wednesday that Russia and Saudi Arabia struck a private deal in September to raise oil output to cool rising prices and informed the United States before a meeting in Algiers with other producers. U.S. sanctions on Irans petroleum sector are set to take effect next month after U.S. President Donald Trump withdrew from the Iran nuclear deal in May. Washington wants to cut Irans oil exports to zero by November, and is encouraging producers such as Saudi Arabia, other OPEC members and Russia to pump more to meet the shortfall."However, these days we have a different problem at hand.In its July 29, 2022, Reuters reported the following:"MOSCOW, July 29 (Reuters) - The OPEC+ group produced almost 3 million barrels per day less crude than foreseen by its quotas in June as sanctions on some members and low investment by some others crippled its ability to assuage the worlds energy crisis, a report showed Friday. The development is a further setback for the U.S. administration of Joe Biden, which had been hoping that OPEC could raise output to compensate for Russian supply disruptions and slow down rising fuel costs and broader inflation. Russian Interfax news agency, citing a source familiar with the data, said level of underproduction by OPEC+ jumped to 320% in June from 256% in May and 220% a month earlier. It also said that the OPEC+ group's combined oil underproduction from the planned levels was 2.84 million barrels per day last month."In your opinion, even though the US is not part of OPEC+, should we play a role in achieving our goals and solving the global crisis by using punishments and incentives to ensure collaborative outcomes? If so, how should we affect the payoffs of the game to ensure socially optimum results? While using sand paper what should you start with The variance of a WSS random process does not depend on time True False Question 13 The cross-covariance of two uncorrelated random processes is 0 True False 4. Find the angle between the orbital angular momentum with the z-axis of a hydrogen atom in the state n = 4, I = 3, m, = -2. What is the location of the point on the number line that isA = -4 to B = 17?OA. 5B. 7OC. 3O D. 9of the way fromSUBMIT Exposure Draft- Proposed Statement of Financial AccountingConcepts, Concepts Statement No. 8, Conceptual Framework forFinancial ReportingDefine changes and corrections of this draft. Function:function [x, y, xyPeak] = projectileTrajectory( v0, theta, y0)%[x, y, peak] = projectileTrajectory(v0, theta, y0)%Computes the trajectory of a projectile as 200 x,y points%Inputs:% v0 =Consider the motion of an object modeled with ideal projectile motion (neglecting air resistance). The trajectory of the object can be derived from basic physics and is given by the formula: \( y=x \t