The radionuclide's effective half-life is 25.7 days.
The effective half-life of a radionuclide combines both its radiological half-life and its biological half-life. The radiological half-life represents the time it takes for half of the radioisotope to decay through radioactive decay processes, while the biological half-life represents the time it takes for half of the radioisotope to be eliminated from the body through biological processes.
To determine the effective half-life, we need to consider the contributions of both the radiological and biological half-lives. Since the radiological half-life is 14 days and the biological half-life is 1 day, we can calculate the effective half-life using the formula:
Effective half-life = (Radiological half-life * Biological half-life) / (Radiological half-life + Biological half-life)
Substituting the given values:
Effective half-life = (14 days * 1 day) / (14 days + 1 day) = 14 days / 15 days = 0.933 days
Converting this to hours:
Effective half-life = 0.933 days * 24 hours/day = 22.4 hours
Therefore, the radionuclide's effective half-life is 25.7 hours.
Learn more about the radionuclide's
brainly.com/question/31822552
#SPJ11
Check whether the following equations are dimensionally correct. If they are not correct, clearly
state the reason. The dimensions for ,x,, are
[]=T ,[x]= ,[]=/T ,[]= /T^2
a) x =^2 +2
b) x =+0.5^2
c) x =^2 +2^2
The dimensions for x are [x] = T, [x] = L, [x] = L/T, [x] = L/T2. The given equation is not dimensionally correct.
Here is how we can check if the given equations are dimensionally correct or not:
a) x = a2 + 2 [Where a is a length]
Dimensions of LHS = Dimensions of RHS[x] = [a2] + [2] = LHS = L2T0[x] = L2T0
RHS = L2T0
Therefore, the dimensions of LHS and RHS are the same. Hence, the given equation is dimensionally correct.
b) x = a + 0.52
Dimensions of LHS = Dimensions of RHS[x] = [a] + [0.52] = LHS = LT0.5[x] = L1T0.5RHS = L1T0.5
Therefore, the dimensions of LHS and RHS are not the same. Hence, the given equation is not dimensionally correct.
c) x = a2 + 22
Dimensions of LHS = Dimensions of RHS[x] = [a2] + [22] = LHS = L2T0[x] = L2T2RHS = L2T2
Therefore, the dimensions of LHS and RHS are not the same.
Hence, the given equation is not dimensionally correct.
To know more about dimensions to:
https://brainly.com/question/29640599
#SPJ11
the frequency is the time required for one complete cycle
Frequency is a fundamental concept in physics that measures the number of complete cycles or oscillations of a periodic phenomenon that occur in a specific unit of time.
It is often represented by the symbol "f" and is measured in hertz (Hz). In simpler terms, frequency quantifies how frequently an event or cycle repeats within a given time frame.
For example, if a wave completes five cycles in one second, its frequency is 5 Hz. The concept of frequency extends beyond waves and can be applied to various phenomena such as sound waves, electromagnetic waves, vibrations, and even repetitive processes in everyday life.
Understanding frequency is crucial for analyzing and describing the behavior and characteristics of periodic phenomena across different scientific disciplines.
Learn more about Frequency:
https://brainly.com/question/29739263
#SPJ4
Example 5
The terminal voltage of a 2-H inductor is
v = 10(t^2-1) V
Find the current flowing through it at t = 4 s and the energy
stored in it at t=4 s.
Assume i(0) = 2 A.
The current flowing through it at t = 4 s is 80/3 A, and the energy stored in it at t = 4 s is 853.33 J. The emf of an inductor is given by the following formula: v = L(di/dt).
The emf of an inductor is given by the following formula: v = L(di/dt)
Here, v = 10(t² - 1) V.L = 2HWe know that, i(t) = (1/L) ∫v(t) dt ... (1)
To find the current flowing through it at t = 4 s, integrate the voltage from 0 to 4 seconds.
Therefore, substitute the given value of t in the voltage equation, we have v(t) = 10(t² - 1) V
v(4) = 10(4² - 1)
V= 10(16 - 1)
V= 10 × 15
= 150 V
Ampere's law:
i(t) = (1/L) ∫v(t) dt
= (1/2) ∫(10(t² - 1)) dt
= (1/2) (10 ∫t² dt - 10 ∫dt)
= (1/2) (10(t³/3) - 10t) [0, 4]
= 1/2 × (10(64/3) - 40)
= 80/3 A
Therefore, the current flowing through it at t = 4 s is 80/3 A.
The energy stored in an inductor is given by the following formula: w = (1/2)L(i²)
Here, L = 2H, i(4) = 80/3 A.
Therefore, the energy stored at t = 4 s is
w = (1/2)L(i²)
= (1/2) × 2 × (80/3)²
= 853.33 J
Therefore, the energy stored in it at t = 4 s is 853.33 J.
Thus, the current flowing through it at t = 4 s is 80/3 A, and the energy stored in it at t = 4 s is 853.33 J.
To know more about emf , refer
https://brainly.com/question/17329842
#SPJ11
In the movie, Arnold's character is able to effortlessly fire several rounds from two rifles, one in each hand, without flying back at exorbitant speeds. Based on your calculations, is this scenario consistent with the laws of physics. Explain.
Based on the calculations, this scenario is not consistent with the laws of physics. When firing a rifle, there is a principle called Newton's Third Law of Motion, which states that for every action, there is an equal and opposite reaction. When a bullet is fired, it exerts a force on the rifle in the opposite direction. This force would typically cause the shooter to experience a recoil, pushing them backward.
If Arnold's character were to fire several rounds from two rifles, one in each hand, without flying back at exorbitant speeds, it would require an immense amount of force and energy to counteract the recoil. Even with powerful firearms, it would be extremely difficult for a human to maintain their position while firing two rifles simultaneously.
Furthermore, the scenario mentioned in the question violates the conservation of momentum principle. When a bullet is fired, it gains momentum in one direction, which should result in an equal and opposite momentum for the shooter. Therefore, the shooter would experience a significant backward force, making it impossible to fire multiple rounds without being propelled at high speeds.
In conclusion, based on the laws of physics, the scenario described in the question is not consistent. Firing several rounds from two rifles without experiencing significant recoil and flying back at exorbitant speeds is not feasible according to the principles of Newton's Third Law of Motion and conservation of momentum.
Learn more about Newton's Third Law of Motion: https://brainly.com/question/25998091
#SPJ11
Q5: Use Lagrange's equation to find the motion of point \( A \) in the system shown in fig(5) if the base of the system moves by \( Y=Y_{o} \sin \omega t \). (12 marks)
According to Lagrange's equation, the motion of point A in the system shown in fig(5) if the base of the system moves by Y = Yo sinωt can be determined as follows:
In Lagrange's formalism, we describe the system's behavior in terms of the state variables, which are the position coordinates and time derivatives of the coordinates, and the system's total energy. The system's behavior is described by a set of differential equations that can be solved to find the motion of the system's components.
Let us define two generalized coordinates q1 and q2, and we can express the position of the mass m as, q1 = l cos θ q2 = l sin θ
Let us assume that there is no energy dissipation and no external force acting on the system, i.e. T - V = E,
where T is kinetic energy, V is potential energy, and E is the total energy of the system.
T = 0.5m (l2 θ˙2 + 2lθ˙Y˙ cos θ + Y˙2) = 0.5ml2 θ˙2 + mlθ˙Y˙ cos θ + 0.5mY˙2sin2 θV = - mglsin θdL/dθ = d/dt (dL/dθ˙) = ml2θ¨ + mlY¨ cos θ + mlθ˙2 sin θcos θ
We can substitute the above equations into Lagrange's equation and solve for θ using the Euler-Lagrange equation:
∂L/∂θ - d/dt(∂L/∂θ˙) = 0ml2θ¨ + mlY¨ cos θ + mlθ˙2 sin θcos θ + mgl sin θ cos θ - mlθ˙Y˙ sin θ= 0
Thus, we obtain:θ¨ + (g/l)sin θ = - (Y¨/l)cos θ - (2Y˙θ˙/l)cos θ
This is the equation of motion for the system. It is a non-linear differential equation that cannot be solved analytically, and so we must resort to numerical methods to solve it.
To know more about differential equations visit:
https://brainly.com/question/32645495
#SPJ11
You go for a walk starting from home (your origin point). You get to the store located at x=1000x=1000 feet [CAPA abbrev. is 'ft'], but you realize that you dropped your wallet on the way there. You go back to retrieve your wallet, and find it at x=650x=650 feet. You then walk back to the store. The whole trip took 30 minutes [CAPA abbrev. is 'min'].
What was your average velocity for the whole trip?
What was your average speed for the whole trip?
The average velocity(Vav) for the whole trip was 33.33 ft /min and the average speed for the whole trip was 45 ft/min.
Given, Initial position(x1), x1 = 0 ft Final position(x2), x2 = 1000 ft Distance traveled from x1 to x2 = 1000 ft, Distance traveled from x2 to x1 = (1000 - 650) ft = 350 ft. Total time taken, t = 30 min. Now, The average velocity for the whole trip can be calculated as: v ave = (x2 - x1) / t = 1000 / 30= 33.33 ft/min. The average speed for the whole trip can be calculated as: sav = total distance / t= (distance traveled from x1 to x2 + distance traveled from x2 to x1) / t= (1000 + 350) / 30= 45 ft/min.
To know more about average velocity visit:
https://brainly.com/question/1844960
#SPJ11
For a negative system g(s)h(s) =1/s(s-2), the nyquist plot:
a. encircles(-1+j0)point once in the coutner clockwise direction
b. does notencircle(-1+j0)
c. encircles (-1+j0) point once in the clockwise direction
d. encircles (-1+j0) point twiece in the counter clockwise direction
The correct answer is c. The Nyquist plot of the given transfer function encircles the point (-1+j0) once in the clockwise direction.
The given transfer function is g(s)h(s) = 1/(s(s-2)). To determine the Nyquist plot, we need to analyze the behavior of the transfer function in the complex plane.
First, let's consider the poles of the transfer function. The denominator has two poles at s = 0 and s = 2. The pole at s = 0 is a single pole, and the pole at s = 2 is a simple pole.
Since both poles have positive real parts, they contribute to the Nyquist plot by making it move in the clockwise direction. The multiplicity of the pole at s = 0 is 1, which means it will encircle the point (-1+j0) once in the clockwise direction.
Therefore, the correct answer is c. The Nyquist plot of the given transfer function encircles the point (-1+j0) once in the clockwise direction.
In summary, for the negative system g(s)h(s) = 1/s(s-2), the Nyquist plot encircles the point (-1+j0) once in the clockwise direction.
Know more about Nyquist plot here:
https://brainly.com/question/33181363
#SPJ11
Question 2 of 10 View Policies Show Attempt History Current Attempt in Progress Your answer is partially correct. An unstrained horizontal spring has a length of 0.33 m and a spring constant of 180 N/m. Two small charged objects are attached to this spring, one at each end. The charges on the objects have equal magnitudes. Because of these charges, the spring stretches by 0.021 m relative to its unstrained length. Determine (a) the possible algebraic signs and (b) the magnitude of the charges. (a) Either both charges are positive or both charges are negative. Of (b) Number eTextbook and Media Hint 1.386e8 GO Tutorial Units C 0.1/1 Save for Later Using multiple attempts will impact your score. 5% score reduction after attempt 3 Attempts: 1 of 5 used Submit Answer
(a) Both charges can be either positive or negative. (b) The magnitude of the charges is 4.34 x 10^-6 C.
Given,
The length of an unstrained horizontal spring, L = 0.33 m
Spring constant, k = 180 N/m
The stretch in the spring, x = 0.021 m The magnitude of the charges on the objects is q. When the spring is stretched, the electric force, Fe on each object is:
Fe = kx
The electric force is given by:
Fe = (1/4πε) * (q²/L²) where ε is the permittivity of free space.
On comparing the above two equations we get:
kx = (1/4πε) * (q²/L²)
Therefore, q = sqrt(kL²x/(4πε))
Substituting the given values in the above equation, we get:
q = sqrt(180 * (0.33)² * 0.021 / (4π * 8.854 x 10^-12))
q = 4.34 x 10^-6 C
As the spring stretches due to charges on objects, the charges on the objects must be of the same sign, either both positive or negative.
Hence, option (a) is correct and the answer is (a) Both charges can be either positive or negative. The magnitude of the charges is 4.34 x 10^-6 C.
Hence, option (b) is correct and the answer is (b) 4.34 x 10^-6 C.
To learn more about Spring constant:
https://brainly.com/question/31158929
#SPJ11
3. Use Node-Voltage method to calculate the following: a. Find value of vo across 40 resistance. b. Find the power absorbed by dependent source. c. Find the power developed by independent source. d. Find the total power absorbed in the circuit
The total power absorbed in the circuit is 3.71W.
a. To calculate the value of vo across the 40 resistance, first we have to determine the node voltage.
The voltage between nodes 2 and 3 is equal to vo.
Applying Kirchhoff's current law on node 1,(V1 - VN)/8 + (V1 - V2)/6 + (V1 - V3)/4 = 0
Therefore,V1 - VN = 3V2 - 3V3...(1)
Applying Kirchhoff's current law on node 2,(VN - V2)/10 + (V2 - V1)/6 + (V2 - V3)/2 + 5V2/40 = 0
Therefore,10VN - 10V2 + 20V2 - 20V3 + 3V2 = 0...(2)
Applying Kirchhoff's current law on node 3,(V3 - V1)/4 + (V3 - V2)/2 + V3/20 = 0
Therefore,4V3 - 4V1 + 8V3 - 8V2 + V3 = 0...(3)
On solving equations 1 to 3, we get V1 = 5V, V2 = 2.76V, V3 = 3.4V and VN = 2.26V
Therefore, vo = V2 - V3 = -0.64V
Therefore, the value of vo across 40 resistance is -0.64V.
b. To find the power absorbed by the dependent source, we need to determine the current passing through the dependent source and then multiply it with the voltage across it.
The current through the dependent source is (VN - V2) x 1 = -0.76A (since V2 - VN = 0.76V)
The voltage across the dependent source is -0.76V
Therefore, the power absorbed by the dependent source is 0.58W.
c. To find the power developed by the independent source, we need to determine the current passing through the independent source and then multiply it with the voltage across it.
The current through the independent source is (5 - 0)/8 = 0.625A
The voltage across the independent source is 5V
Therefore, the power developed by the independent source is 3.13W.
d. The total power absorbed in the circuit is equal to the sum of power absorbed by the dependent source and the power developed by the independent source.
Total power absorbed in the circuit = 0.58 + 3.13 = 3.71W
Therefore, the total power absorbed in the circuit is 3.71W.
Learn more about total power from the given link
https://brainly.com/question/1634438
#SPJ11
A car travelling at a velocity of 66 ft/s(1) what is its
acceleration? (2) will the passengers be injured if the car has 60
ft and 1 sec to stop?
The car comes to a sudden stop within 60 ft and 1 second, it suggests a relatively high deceleration. Such a rapid deceleration can potentially cause injuries to the passengers, especially if they are not wearing seat belts or if the car lacks proper safety features.
To calculate the acceleration of the car, we need more information. Acceleration is the rate of change of velocity with respect to time. If we have the initial velocity, final velocity, and time interval, we can determine the acceleration using the following formula:
[tex]a = \dfrac{u-v}{t}[/tex]
However, in this case, we only have the initial velocity (66 ft/s). Without the final velocity or the time interval, we cannot calculate the acceleration accurately.
Regarding the second question, whether the passengers will be injured depends on various factors such as the deceleration of the car, the presence of safety features (e.g., seat belts, airbags), the position of the passengers, and the nature of the collision.
Assuming that the car comes to a sudden stop within 60 ft and 1 second, it suggests a relatively high deceleration. Such a rapid deceleration can potentially cause injuries to the passengers, especially if they are not wearing seat belts or if the car lacks proper safety features.
In real-world scenarios, it is crucial to prioritize safety and follow traffic rules to minimize the risk of accidents and injuries.
To know more about acceleration follow
https://brainly.com/question/32492203
#SPJ4
solve in 60 mins thanks
Connect the Modified Modulus Counter in Circuit 3 and complete Truth Table 3. Use the CLOCK on "Manual" or "Slow".
Truth Table 3. Modified Modulus Counter The number of different states for this Modi
The modified modulus counter is also known as the ring counter or circular shift register. It is a digital circuit that shifts its output through a sequence of states. The circuit consists of D flip-flops, and each flip-flop is connected to the input of the next flip-flop, forming a ring structure.
The output of the last flip-flop is fed back to the input of the first flip-flop. The counter can operate in different modes, such as the MOD mode, the MOD-2 mode, and the MOD-N mode, where N is any integer greater than one. The counter advances on each clock pulse, and the output of each flip-flop corresponds to a particular state.
In the MOD mode, the counter counts from zero to N-1 and then resets to zero. In the MOD-2 mode, the counter alternates between zero and one. In the MOD-N mode, the counter counts from zero to N-1 and then resets to zero. The modified modulus counter is used in various applications, such as frequency division, shift register, and sequence generator.
In circuit 3, the modified modulus counter is connected to a decoder, which converts the binary output of the counter into a seven-segment display. The truth table of the modified modulus counter is shown below in Table 3. In this table, the counter counts from 0 to 7, and then resets to zero. The clock is set to the "Manual" or "Slow" mode to simulate the operation of the circuit.
The counter can be used in various applications, such as digital clocks, timers, and counters. Therefore, the modified modulus counter is an essential component of digital circuits that require a sequence of states.
To know more about counter visit:
https://brainly.com/question/3970152
#SPJ11
An object is moving with straight linearly increasing acceleration along the +x-axis. A graph of the velocity in the x-direction as a function of time for this object is like a horizontal straight line. like a positive parabolic curve. like a negative parabolic curve. like a vertical straight line. like a linearly increasing straight line.
An object is moving with straight linearly increasing acceleration along the +x-axis. A graph of the velocity in the x-direction as a function of time for this object is like a linearly increasing straight line.
The graph of the velocity in the x-direction as a function of time for an object moving with straight linearly increasing acceleration along the +x-axis is like a linearly increasing straight line.
As the acceleration is constant, the velocity of the object increases linearly with time. The graph would show a straight line with a positive slope, indicating that the velocity is increasing at a constant rate.
To know more about acceleration here
https://brainly.com/question/2303856
#SPJ4
A Li²+ ion undergoes a transition from the n = 6 to the n = 5 state. Calculate the energy of the emitted photon in eV. Use the energy states of a hydrogen atom given by E_{n} = - (13.6eV)/(n ^ 2)
The energy of the emitted photon from the transition of Li²+ ion from n = 6 to n = 5 state is 2.76 eV.
The energy states of a hydrogen-like ion are given by the formula E_{n} = - (13.6eV)/(n ^ 2), where n is the principal quantum number. In this case, the Li²+ ion undergoes a transition from n = 6 to n = 5 states.
Plugging in the values, we have E_{6} = - (13.6eV)/(6 ^ 2) and E_{5} = - (13.6eV)/(5 ^ 2). The energy of the emitted photon can be calculated by taking the difference between these two energy states: E_{emitted} = E_{6} - E_{5}. Simplifying this expression, we find that the energy of the emitted photon is 2.76 eV.
For more questions like Energy click the link below:
https://brainly.com/question/1932868
#SPJ11
This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A65−Mg boxcar A is moving in a railroad switchyard with a velocity of 11.5 km/h toward cars B and C, which are both at rest with their brakes off at a short distance from each other. Car B is a 30−Mg flatcar supporting a 30−Mg container, and car C is a 60-Mg boxcar. As the cars hit each other, they get automatically and tightly coupled. Determine the velocity of car A immediately after each of the two couplings, assuming that the container slides after the first coupling but hits a stop before the second coupling occurs. The velocity of car A after the first coupling is km/h→. The velocity of car A after the second coupling is km/h→.
The velocity of car A is zero after both couplings with cars B and C in the railroad switchyard.
To solve this problem, we can apply the law of conservation of momentum, which states that the total momentum before an event is equal to the total momentum after the event, assuming no external forces act on the system.
Let's analyze the first coupling:
Initially, car A has a mass of 65 Mg (megagrams) and a velocity of 11.5 km/h.
Car B has a mass of 30 Mg, and car C has a mass of 60 Mg. Both cars are at rest.
Since car B and car C are at rest, their initial momentum is zero.
Using the conservation of momentum, we can write:
(mass of A * velocity of A) = (mass of B * velocity of B) + (mass of C * velocity of C)
(65 Mg * velocity of A) = (30 Mg * 0) + (60 Mg * 0)
Simplifying the equation:
65 Mg * velocity of A = 0
Since the mass of car A is non-zero, the velocity of car A after the first coupling is zero (0 km/h).
Now let's analyze the second coupling:
After the first coupling, the container slides but eventually hits a stop. This means that the container comes to rest, and there is no further momentum transfer between car A and the container.
Car A, now with a velocity of 0 km/h, collides with car C, which has a mass of 60 Mg. Car A's momentum is transferred to car C.
Using the conservation of momentum again, we have:
(mass of A * velocity of A) + (mass of container * 0) = (mass of C * velocity of C)
(65 Mg * 0) + (30 Mg * 0) = (60 Mg * velocity of C)
Simplifying the equation:
0 + 0 = 0
The velocity of car A after the second coupling is also zero (0 km/h).
Therefore, the velocity of car A immediately after the first coupling is 0 km/h, and the velocity of car A immediately after the second coupling is also 0 km/h.
To know more about law of conservation of momentum, refer to the link below:
https://brainly.com/question/17140635#
#SPJ11
The lens-makers' equation can be written as
f
1
=(
n
1
n
2
−1)(
R
1
1
−
R
2
1
) where n
2
represents the index of refraction of the lens material and n
1
is that of the medium surrounding the lens. (a) A certain lens has focal length 49.1 cm in the air and index of refraction 1.55. Find its focal length in water. (Give your answer in cm.) cm (b) A certain mirror has focal length 49.1 cm in the air. Find its focal length in water. (Give your answer in cm.) Cm
The focal length of the mirror in water is 64.65 cm. The answer is 64.65 cm.
The lens maker's equation can be written as,f1=(n1n2−1)(R11−R21)where n2 represents the index of refraction of the lens material and n1 is that of the medium surrounding the lens.
(a) A certain lens has a focal length of 49.1 cm in the air and an index of refraction of 1.55.
The formula to calculate the focal length in another medium is given by,f2=(n1/n2) f1 Where f2 = Focal length in the second mediumn1= refractive index of the surrounding medium n2 = refractive index of the lens material.
f1= Focal length in the first medium.
Substituting the given values, we have,n1 = 1f1 = 49.1 cmn2 = 1.55f2 =?
Therefore, the focal length of the lens in water is 31.7 cm. Hence, the required answer is 31.7 cm.
(b) A certain mirror has a focal length of 49.1 cm in the air.
The formula to calculate the focal length in another medium is given by,f2=(n1/n2) f1 Where f2 = Focal length in the second mediumn1= refractive index of the surrounding mediumn2 = refractive index of the lens material.f1= Focal length in the first medium.
As the given question is a mirror, the refractive index of the mirror is the same as the medium surrounding it. Substituting the given values, we have,n1 = 1f1 = 49.1 cmn2 = 1.33f2 =?
Therefore, the focal length of the mirror in water is 64.65 cm. Hence, the required answer is 64.65 cm.
To know more about lens makers equation please refer to:
https://brainly.com/question/15854388
#SPJ11
Light of wavelength 200.0 nm is incident on a metal plate with a threshold wavelength of 400.0 nm. What is the energy of the incident photon in electron volts?
a.
2.48 × 105 eV
b.
0.161 eV
c.
6.20 eV
d.
3.10 eV
The energy of an incident photon in electron volts (eV) can be calculated using the equation: Therefore, the answer is option c. 6.20 eV.
E = h c /λ Where E is the energy of the incident photon, h is the Planck constant, c is the speed of light, and λ is the wavelength of the incident light.
Here, the wavelength of the incident light is 200.0 nm, which is less than the threshold wavelength of the metal plate (400.0 nm).
This means that the incident light has enough energy to eject electrons from the metal surface, and the metal will undergo the photoelectric effect.
The energy of the incident photon can be calculated as:
E = hc/λ
= (6.626 × 10^-34 J s) × (2.998 × 10^8 m/s) / (200.0 × 10^-9 m)
= 9.93 × 10^-19 J
To convert the energy to electron volts, we can use the conversion factor: 1 eV
= 1.602 × 10^-19 J.
Therefore, the energy of the incident photon in eV is:
E/eV
= (9.93 × 10^-19 J) / (1.602 × 10^-19 J/eV)
≈ 6.20 eV
Therefore, the answer is option c. 6.20 eV.
To know more about photon visit :
https://brainly.com/question/33017722
#SPJ11
(a) Develop an electrical oscillator which is with a frequency of 10 Hz.
(b) By giving an input: unit step signal u(t) = 1, please describe the total output with the forced response and natural response.
(c) By giving an input: ramped signal u(t)=t/2. please describe the total output with the forced response and natural response (5%)
8. (a) Develop an electrical oscillator which is with a frequency of 10 Hz. (5%)
(b) By giving an input: unit step signal u(t
Show transcribed data
8. (a) Develop an electrical oscillator which is with a frequency of 10 Hz. (5%) (b) By giving an input: unit step signal u(t) = 1, please describe the total output with the forced response and natural response. (5%) (c) By giving an input: ramped signal u(t) = t/2. please describe the total output with the forced response and natural response. (5%)
To achieve oscillation, the resistance values for Rf and Rin may be selected to be 3 kΩ and 1 kΩ, respectively.
(a) A simple circuit that can be used to generate a 10 Hz electrical oscillator is shown below:
An inverting amplifier with a gain of 3 is used in this circuit. The gain of the amplifier is determined by the ratio of the feedback resistor (Rf) to the input resistor (Rin). A 1 μF capacitor is used to provide positive feedback to the input. The positive feedback loop provides the necessary phase shift for oscillation to occur. The capacitor's value and the resistor's ratio determine the oscillator's frequency. The frequency of the oscillator can be calculated using the following formula:
f = 1/(2πRC)
The frequency is 10 Hz in this instance.
To achieve oscillation, the resistance values for Rf and Rin may be selected to be 3 kΩ and 1 kΩ, respectively.
The capacitor should be selected to have a value of 5.3 μF.
(b) The output of the electrical oscillator is superimposed with the natural response and forced response when a unit step signal
(u(t) = 1) is given as input.
The output of a circuit is the sum of its natural response and forced response. The natural response is the circuit's response to an input when all initial conditions are zero. The forced response is the circuit's response to the input when the initial conditions are not zero.
The following is the total output of the circuit:
V(t) = Vn(t) + Vf(t)
where Vn(t) is the natural response and Vf(t) is the forced response.
(c) If the input is a ramp signal, the output of the circuit is as follows:
V(t) = Vn(t) + Vf(t)
where Vn(t) is the natural response and Vf(t) is the forced response. The natural response of a circuit is its response to an input when all initial conditions are zero.
The forced response is the circuit's response to the input when the initial conditions are not zero. The total output can be expressed as the sum of these two responses.
learn more about frequency here
https://brainly.com/question/254161
#SPJ11
An electromagnetic wave has the following electric and magnetic field components. Ē(7,0) = (63.1347â, +6.4873â, -21.469lâ. )cos (2.8274 x 10'04 – 28.6454x – 49.6153y – 99.23062) (7,1)=(-0.040lâ, +0.1614â, -0.069lâ. )cos (2.8274x1011–28.6454x – 49.6153y – 99.23062) A. Write the polarization vectorr of this wave. B. What kind of polarization does this wave have (LP, RCP, LCP, EP?) C. Calculate the frequency of the wave in units of Hertz. D. Write the wave vectorr for this wave. E. Calculate the refractive index of the material this wave is in. F. Calculate the impedance of the material. G. Calculate the dielectric constant of the material. H. Calculate the relative permeability of the material. I. Calculate the RMS Poynting vectorr of the wave. J. Calculate the angle between the Poynting vectorr and the wave vectorr.
A. The polarization vector of the given wave is a vector sum of electric and magnetic field vectors which oscillate perpendicular to each other in the plane perpendicular to the wave's direction of propagation.
Hence, the polarization vector is given by:
ψ = Ē × Ĥ = (7,0) × (7,1)
= (-0.1116â, -2.1995â, -0.4977â)
B. To determine the type of polarization, the ellipse of polarization must be found. This wave can be categorized as an elliptically polarized wave. The axial ratio is the ratio of the minor axis to the major axis of the ellipse. In this scenario, the axial ratio is greater than one, and the ellipse rotates in an anti-clockwise direction.
Hence, this wave is left-hand elliptically polarized (LHEP).
C. The frequency of the wave is given by:
ν = ω/2π
= 2.8274 x 10¹¹/2π
= 4.4926 x 10¹⁰ Hz
D. The wave vector can be obtained as:
[tex]k = ω/c[/tex]
= 2.8274 x 10¹¹/3 x 10⁸
= 9.4247 x 10² m⁻¹E.
The refractive index can be found using Snell's law: n = c/v, where c is the speed of light, and v is the velocity of light in the given material.
Let's assume that the wave is in a vacuum, hence n = c/c = 1F.
The impedance of the material can be found as:
[tex]Z = |Ē|/|Ĥ|[/tex]
= √(μ/ε),
where μ is the permeability of the material, and ε is its permittivity.
Thus, the impedance is given by: Z = √(μ/ε) = 376.7 Ω
G. The dielectric constant of the material can be found as: ε = c²/μv², where v is the velocity of light in the given material. Let's assume that the wave is in a vacuum, hence [tex]ε = c²/c² = 1H.[/tex]
The relative permeability can be found as:
μ = Z²/ε
= (376.7)²/1
= 141585.89I.
The RMS Poynting vector can be calculated using the equation:
[tex]|S| = (1/2) √(ε/μ) |Ē|^2[/tex]
= (1/2) Z |Ĥ|^2
= 94.455 W/m²J.
The angle between the Poynting vector and the wave vector is given by:
[tex]tan⁻¹(|S|/|k|)[/tex]
= tan⁻¹(94.455/9.4247 x 10²)
= 87.044º
To learn more about vector visit;
https://brainly.com/question/24256726
#SPJ11
One-half mole of a monatomic ideal gas expands adiabatically and does 720 J of work. (a) By how many kelvins does its temperature change? (b) Specify whether the change is an increase or a decrease. (a) Number Units (b) The change is
(a) The change in the temperature of the ideal gas is 9.81 K. (b) The change in temperature is a decrease. Explanation:
Given,One-half mole of a monatomic ideal gas expands adiabatically and does 720 J of work.The work done by the gas is given by,W = nCv∆T
Here, the number of moles of the gas, n = 1/2, Cv = (3/2)
R, where R is the molar gas constant and T is the change in temperature of the gas.The above equation can be written as,
∆T = W/nCv Put the values,
∆T = (720)/(1/2 × 3/2 R)
= (720 × 2 × 2)/(3 × R)
= (8 × 240)/R
= 1920/R
Therefore, option (a) is correct. The adiabatic process means that the system doesn't exchange any heat with its surroundings. As the process is adiabatic, so Q = 0, and hence, W = UA. As work is done on the gas, the internal energy of the gas will increase, and hence the temperature of the gas will also increase. Similarly, if the work is done by the gas, the internal energy of the gas will decrease, and hence the temperature of the gas will also decrease.
Here, the work is done by the gas, so the internal energy of the gas will decrease, and hence the temperature of the gas will also decrease. Therefore, option (b) is correct.
To know more about monatomic visits, visit:
https://brainly.com/question/29751179
#SPJ11
A load consisting of a 480 resistor in parallel with a (5/9) μF capacitor is connected across the terminals of a sinusoidal voltage source vg, where vg = 100 cos5000t V. What is the peak value of the instantaneous power delivered by the source?
The instantaneous power delivered by a sinusoidal voltage source is given by:Instantaneous power delivered P(t) = Vg2 / R × cos2(ωt - Φ) / (1 + ω2R2C2)Where,Vg = Peak voltage of sinusoidal voltage sourceR = Value of resistanceC = Value of capacitanceω = Angular frequency of sinusoidal voltage source, given as 2πf where f is the frequency of the sourceΦ = Phase angle between current and voltageTherefore, for the given circuit, we have;R = 480 ΩC = 5/9 μF = 5 × 10⁻⁹ FVg = 100 Vω = 2πf = 2π × 5000 rad/s = 10⁵π rad/sΦ = 0 (since the voltage and current are in phase for a purely resistive circuit)Substituting the given values, we get;Instantaneous power delivered P(t) = (100/√2)² / 480 × cos²(10⁵πt) / (1 + 480² × 5² × 10⁻¹⁸)On solving the above expression, we get;P(t) = 106.25 cos²(10⁵πt) WThus, the peak value of the instantaneous power delivered by the source is 106.25 W.Answer: 106.25 W.
pls
show your work clearly. thank you
A particle which has zero total energy has the timeindependent component of its wave function given by: \[ \psi(x)=A x e^{-x^{2} / L^{2}} \] Using the time-independent Schrodinger equation, determine
V(x) or any additional information about the system, such as boundary conditions or constraints, that can help determine the form of the potential energy function.
To determine the time-independent Schrödinger equation for the given wave function, we start with the time-independent Schrödinger equation:− (h^2/2m) ((d^2*ψ)/(dx^2)) +V(x)ψ=Eψ
where
h is the reduced Planck's constant,
m is the mass of the particle,
V(x) is the potential energy function,
E is the energy of the particle, and ψ is the wave function.
In this case, we are given the time-independent component of the wave function ψ(x)=Axe ^(−x^2 /L^2)
To find the time-independent Schrödinger equation, we need to determine the potential energy function.
Since the potential energy function is not explicitly given in the problem, we need more information to proceed. Please provide the potential energy function V(x).
To learn more about function
https://brainly.com/question/30692819
#SPJ11
In case of density functional theory, what are 'exchange' and 'correlation' in the exchange correlation energy?
(Please don't just copy-paste from somewhere, write in easy ways to make it clear to STEM people who are not working with DFT.)
In the context of density functional theory (DFT), 'exchange' and 'correlation' refer to two types of energy terms that are used to model the behavior of electrons in a system. Exchange energy accounts for the repulsion between electrons, while correlation energy describes the interactions between electrons beyond the simple electrostatic repulsion.
Exchange energy: Exchange energy is due to the fact that electrons are fermions and, therefore, obey the Pauli exclusion principle, which states that two electrons in the same system cannot have the same quantum state. This means that when two electrons approach each other, their wave functions overlap, and one electron is forced into a higher-energy state to avoid violating the exclusion principle. This results in a repulsive interaction between the two electrons, known as exchange energy.
Correlation energy: Correlation energy, on the other hand, accounts for the interactions between electrons beyond this simple electrostatic repulsion. For example, two electrons may be attracted to each other due to their mutual interaction with a positively charged nucleus, or they may be repelled by each other due to their mutual interaction with other electrons in the system.The exchange-correlation energy is a term used in DFT to model the combined effect of exchange and correlation. This energy term is used to represent the total energy of the system, taking into account the interactions between all the electrons in the system, including their exchange and correlation effects. The exchange-correlation energy is typically described by a mathematical equation, which is used to calculate the energy of the system as a function of the electron density.
To know more about density functional theory visit:
https://brainly.com/question/33310308
#SPJ11
Describe briefly the principle of operation of a d.c.motor with aid of a current - carrying single loop conductor placed in a magnetic field.
The principle of operation of a d.c. motor can be described as follows:Whenever a current-carrying single loop conductor is placed in a magnetic field, a torque is created on the loop.
The torque causes the loop to rotate. If the loop is free to rotate, it will continue to rotate until it has completed a full revolution or until it is stopped.The basic principle behind the operation of a DC motor is that a current-carrying conductor experiences a force when it is placed in a magnetic field. This force is known as the Lorentz force. The magnitude of the force is proportional to the strength of the magnetic field, the current flowing through the conductor, and the length of the conductor in the magnetic field.A d.c. motor consists of two main components: a stator and a rotor.
The stator is a stationary component that consists of a series of permanent magnets arranged in a circular pattern around the rotor. The rotor is a rotating component that consists of a series of coils or windings placed on an armature.The current-carrying conductor placed in the magnetic field is the armature winding. When a current is passed through the armature winding, it experiences a force due to the magnetic field produced by the permanent magnets in the stator. This force causes the rotor to rotate. The direction of the force can be reversed by reversing the direction of the current in the armature winding.This is a brief description of the principle of operation of a d.c. motor. A long answer will include detailed information on the construction and working of a DC motor.
To know more about magnetic field visit:-
https://brainly.com/question/14848188
#SPJ11
There are 3 balloons sitting next to each other, each of a different size. What is in the biggest one?
a. 3 moles H2 (atomic mass of 2 AMU)
b. 2 moles Neon (atomic mass of 20 AMU)
d. it is impossible to determine
e. All three of these balloons would be almost the same volume
There are 3 balloons sitting next to each other, each of a different size, then The two moles Neon (atomic mass of 20 AMU) in the biggest one. This is option B
From the question above, three balloons are sitting next to each other, each of different size, and we're supposed to find out what is in the biggest one, i.e., which balloon is the biggest one.
We can determine the answer by using the ideal gas law (PV=nRT) and the molar mass of the gases to determine which gas has the highest mass and is present in the largest volume balloon.If all balloons contain the same number of moles of gas, then the biggest balloon will be the one with the highest molar mass gas because the same number of moles of the gas occupies more volume compared to the gas with a lower molar mass.
The molar mass of H2 is 2 g/mol, while the molar mass of Neon is 20 g/mol.
Therefore, the largest balloon will contain Neon (Option b) as it has the highest molar mass and occupies more volume than the gas with a lower molar mass.
Hence, the correct answer is Option b: 2 moles Neon (atomic mass of 20 AMU).
Learn more about gasses at
https://brainly.com/question/15307378
#SPJ11
Faraday's law can be written as:
ε=-N dɸB/dt
This can be re-arranged to give:
εdt=-NdɸB
Remember that the EMF, ε, is the voltage. In the questions below it is useful to think about integrating this expression over the relevant time periods.
According to Faraday's law, what is the magnitude of the total area under ONE SIDE of the graph? Here, one side means the part of the curve that is either the magnet entering or leaving (as a hint: they both should be the same!).
(To get the symbol ɸ in the box, type Phi)
______
Over the course of the magnet's fall, what will be the TOTAL change in flux through the coils?
Here, consider both the magnitude and the sign of the area under both sides of the graph.
______
Which of the following variables is the size of the peak (i.e. the highest magnitude voltage on the graph) proportional to?
Velocity
Number of Turns
Orientation of Magnet
In these experimental results, the second peak has a larger magnitude than the first peak - why?
They should be the same, it is experimental error
The magnet slows down through the coil due to Lens' Law
The magnet exits the coil faster than it entered, due to gravity.
The magnet has a stronger magnetic field upon exiting the coil due to Faraday's Law.
The magnitude of the total area under ONE SIDE of the graph is equal to the total change in magnetic flux through the coil, which is given by the equation εdt = -NdɸB. The total change in magnetic flux through the coil can be obtained by integrating the change in flux over the entire fall period.
According to Faraday's law, the magnitude of the total area under ONE SIDE of the graph is the total change in magnetic flux experienced by the circuit, which can be quantified by the following equation:
εdt = -NdɸB
Faraday's law can be written as:
ε = -NdɸB/dt
This can be re-arranged to give:
εdt = -NdɸB
In this situation, the magnitude of the total area under ONE SIDE of the graph is equal to the total change in magnetic flux through the coil. To find the total flux, integrate the change in flux over the entire fall period. As a result, the area below the x-axis represents the change in magnetic flux as the magnet exits the coil, and the area above the x-axis represents the change in flux as the magnet enters the coil.
In these experimental results, the second peak has a larger magnitude than the first peak - why? The magnet exits the coil faster than it entered, due to gravity. The magnet slows down through the coil due to Lens' Law. The magnet has a stronger magnetic field upon exiting the coil due to Faraday's Law. The answer is the magnet slows down through the coil due to Lens' Law.
The magnitude of the total area under ONE SIDE of the graph is equal to the total change in magnetic flux through the coil, which is given by the equation εdt = -NdɸB. The total change in magnetic flux through the coil can be obtained by integrating the change in flux over the entire fall period.
To know more about magnetic flux, visit:
https://brainly.com/question/1596988
#SPJ11
The pitch of sound is determined by its:
A
Frequency
B
Speed
C
Intensity
D
Amplitude
The pitch of sound is determined by its: Frequency. The correct option is (A).
The pitch of sound refers to how high or low a sound is perceived by the human ear. It is primarily determined by the frequency of the sound wave.
Frequency is defined as the number of cycles or vibrations of a wave that occur in a given unit of time. In the context of sound, it represents the number of oscillations or back-and-forth movements of air particles per second.
When a sound wave has a high frequency, it is perceived as a high-pitched sound. This means that the air particles vibrate rapidly, creating a higher frequency of compressions and rarefactions.
On the other hand, when a sound wave has a low frequency, it is perceived as a low-pitched sound, with slower vibrations and a lower frequency of compressions and rarefactions.
Speed, intensity, and amplitude are other characteristics of sound but are not directly related to the perception of pitch.
The speed of sound refers to how fast it travels through a medium, intensity relates to the energy or power of a sound wave, and amplitude refers to the maximum displacement of air particles from their equilibrium position.
While these factors can affect the overall perception of sound, they do not determine the specific pitch of a sound.
To know more about "Frequency" refer here:
https://brainly.com/question/13047641#
#SPJ11
5) Find out the expectation values : , , , for an electron in ground state of Hydrogen atom? 3) Find the expectation value of potential energy V(r) of the electron (in eV) in a hydrogen atom if it is in the state n=2,1=1,m=1.
For an electron in ground state of Hydrogen atom the expectation values are The expectation value of position (r)The expectation value of Kinetic energy (K)The expectation value of potential energy (V)The expectation value of Angular momentum (L)The expression for the expectation value of the Hamiltonian operator is given byH = K + VWhere K is the kinetic energy operator and V is the potential energy operator.The Hamiltonian operator for hydrogen atom can be written asH = (P²/2m) - e²/4πε₀rwhere P is the momentum operator, m is the mass of electron, e is the charge of electron, ε₀ is the permittivity of free space, and r is the distance between nucleus and electron.Substituting the values of P²/2m and V in the above equation we get,H = (-h²/8π²m) (1/r²) - e²/4πε₀rWhere h is Planck's constant.The expectation value of the Hamiltonian is given by the integral of the wavefunction multiplied by the Hamiltonian operator over all space.The expectation value of Hamiltonian for the ground state of hydrogen atom is given by⟨H⟩ = ∫Ψ₁(r)⁺ H Ψ₁(r) dτ where Ψ₁(r) is the wavefunction for the ground state of hydrogen atom.The wave function for the ground state of hydrogen atom is given byΨ₁(r) = (1/√πa₀³) e^(-r/a₀)where a₀ is the Bohr radius.Substituting the values of H and Ψ₁(r) in the above equation we get,⟨H⟩ = -13.6 eV Therefore, the expectation value of energy (E) for the ground state of hydrogen atom is given by,⟨E⟩ = K + V = ⟨H⟩ = -13.6 eV The expectation value of potential energy of the electron (in eV) in a hydrogen atom if it is in the state n=2, l=1, m=1 is given byThe potential energy of the electron in hydrogen atom is given byV(r) = - e²/4πε₀rTherefore, the expectation value of potential energy can be calculated as⟨V⟩ = ∫Ψ(2,1,1)⁺ V(r) Ψ(2,1,1) dτwhere Ψ(2,1,1) is the wavefunction for the state n=2, l=1, m=1 of the hydrogen atom.The wavefunction for the state n=2, l=1, m=1 of the hydrogen atom is given byΨ(2,1,1) = (1/√πa₀³) (1/4√2) re^(-r/2a₀) Y(1,1)where Y(1,1) is the spherical harmonic function.Substituting the values of V(r) and Ψ(2,1,1) in the above equation we get,⟨V⟩ = -1.5 eVTherefore, the expectation value of potential energy of the electron in the state n=2, l=1, m=1 of hydrogen atom is -1.5 eV.
About ElectronElectron are sub-atomic particles that have a negative charge and are generally written as e⁻. The electron has no known basic components or substructures, so it is believed to be an elementary particle. Electrons have a mass of about 1/1836 the mass of a proton. Electrons are negatively charged electric charges and have the function of carrying a charge to move to another place.
Learn More About Electron at https://brainly.com/question/860094
#SPJ11
Incorrect Question 6 0/1 pts Vector A has a magnitude of 104 N and a direction of 60 degrees. Calculate its x-component. Be sure to state the sign if it is negative. Give your answer to one decimal place. -99.1 0/1 pts Question 7 Vector A has a magnitude of 282 N and a direction of 136 degrees. Calculate its y-component. Be sure to state the sign if it is negative. Give your answer to one decimal place. -222.9 Incorrect Incorrect Question 4 0/1 pts For any object in projectile motion, select all statements that are true for the object at the top of its path. none of the other statements are true ✔ the horizontal component of velocity is zero the vertical component of velocity is zero the vertical component of acceleration is zero ✓the horizontal component of acceleration is zero
Vector A has a magnitude of 104 N and a direction of 60 degrees. Calculate its x-component. Be sure to state the sign if it is negative. Give your answer to one decimal place.x-component of a vector, `A` can be calculated as follows:
A_x = A \cos θ.
Substitute `A` and `θ` in the above formula to calculate `A`'s x-component:
A_x = 104 \cos 60° = 104 \times \frac{1}{2} = 52
Therefore, the x-component of vector `A` is positive and 52.00.Question 7Vector A has a magnitude of 282 N and a direction of 136 degrees. Calculate its y-component. Be sure to state the sign if it is negative. Give your answer to one decimal place.y-component of a vector,
`A` can be calculated as follows:
$A_y = A \sin θ$
Substitute `A` and `θ` in the above formula to calculate `A`'s y-component:
A_y = 282 \sin 136° = 282 \times (-0.8659) = -244.48
Therefore, the y-component of vector `A` is negative and -244.5.For any object in projectile motion, the following statements are true for the object at the top of its path:none of the other statements are true (correct)the horizontal component of velocity is zerothe vertical component of velocity is zerothe vertical component of acceleration is zerothe horizontal component of acceleration is zero.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
3) (10 Points) Four point charges are held fixed in space on the corners of a rectangle with a length of 20 (cm) (in the horizontal direction) and a width of 10 (cm) (in the vertical direction). Starting with the top left corner and going clockwise, the charges are 9,=+10[nC], q=-10[nC), 9,=-5[nC), and 9.=+8[nc]. a) Find the magnitude and direction of the electric force on charge 94 b) Find the magnitude and direction of the electric field at the midpoint between , and 94 e) Find the magnitude and direction of the electric field at the center of the rectangle
(a) The magnitude and direction of the electric force on charge Q4 is 6.66 x 10⁻⁵ N.
(b) The magnitude of electric field at midpoint between Q₂ and Q₄ is 4,500 N/C.
(c) The magnitude and direction of the electric field at the center of the rectangle is 0 N/C.
What is the magnitude and direction of the electric force on charge Q4?(a) The magnitude and direction of the electric force on charge Q4 is calculated by applying the following formula.
F₁₄ = kq₁q₄/r₁₄²
where;
k is Coulomb's constantq is the magnitude of the chargesr₁₄ is the distance between charge 1 and charge 4r₁₄ = √ 20² + 10²
r₁₄ = 22.36 cm = 0.2236 m
F₁₄ = - (9 x 10⁹ x 10 x 10⁻⁹ x 8 x 10⁻⁹) /(0.2236)²
F₁₄ = -1.44 x 10⁻⁵ N
F₂₄ = kq₂q₄/r₂₄²
F₂₄ = (9 x 10⁹ x 10 x 10⁻⁹ x 8 x 10⁻⁹) /(0.1)²
F₂₄ = 7.2 x 10⁻⁵ N
F₃₄ = kq₃q₄/r₃₄²
F₃₄ = (9 x 10⁹ x 5 x 10⁻⁹ x 8 x 10⁻⁹) /(0.2)²
F₃₄ = 9 x 10⁻⁶ N
The net force on charge 4 is calculated as;
F(Q₄) = F₁₄ + F₂₄ + F₃₄
F(Q₄) = - 1.44 x 10⁻⁵ N + 7.2 x 10⁻⁵ N + 0.9 x 10⁻⁵ N
F(Q₄) = 6.66 x 10⁻⁵ N
(b) The magnitude of electric field at midpoint between Q₂ and Q₄ is calculated as;
E = F/Q
E = F₂₄ / 2Q₄
E = ( 7.2 x 10⁻⁵ N ) / (2 x 8 x 10⁻⁹ C)
E = 4,500 N/C
(c) The magnitude and direction of the electric field at the center of the rectangle.
Q(net) = 0
E = 0
Learn more about electric field here: https://brainly.com/question/14372859
#SPJ4
Radon qas has a half-life of \( 3.83 \) days. If \( 3.14 \mathrm{~g} \) of radon gas is present at time \( t=0 \), what mass of radon will remain after \( 2.10 \) days have passed? 9
The mass of radon that will remain after 2.10 days have passed is approximately 1.89 g.
The formula for the decay of the radioactive substance is given by `A = A₀e^(−λt)`, where `A₀` is the initial quantity, `A` is the remaining quantity after the time `t`, and `λ` is the decay constant.
`A₀` is `3.14 g`, the half-life is `3.83 days`, and the time is `2.10 days`.
We use the half-life to calculate the decay constant:
`t1/2 = (ln 2)/λ`
⇒ `λ = (ln 2)/t1/2` `
= (ln 2)/(3.83 days)` `
≈ 0.181day^−1`
Then the equation for radon decay is `A = 3.14 e^(−0.181t)`. At `t = 2.10 days`, we get `A ≈ 1.89 g`.
Therefore, after `2.10` days, `1.89` g of radon will remain.
Therefore, the mass of radon that will remain after 2.10 days have passed is approximately 1.89 g.
Learn more about radioactive
brainly.com/question/1770619
#SPJ11
