Yes, there can be a non-zero electric field at a point in space where no charged object is present. No, there cannot be an electric field equal to zero at a point where a charged object is present.
An electric field is defined as the force experienced per unit charge at a point in space. Even if there is no charged object present, an electric field can be present due to the presence of other charges in the surrounding area. For example, if there are charges present on a nearby conductor, the electric field can extend into the surrounding space.
On the other hand, it is not possible for an electric field to be equal to zero at a point where a charged object is present. The electric field is a measure of the force exerted on a test charge placed at that point, and a charged object exerts an electric force on other charges. Therefore, an electric field must be present at any point where a charged object is present.
The electric field can be zero at a certain point in space if there are no charges around that point or if the charges around that point balance each other out to create a net zero electric field.
To know more about electric field click below:
https://brainly.com/question/8971780#
#SPJ4
after the capacitor is charged to its maximum value, the capacitor and resistor are disconnected from the battery and from each other. then they are connected in parallel, so that the capacitor discharges through the resistor. how long will it take for the voltage across the capacitor to drop to 2.50 v?
The time will it take for the voltage across the capacitor to drop to 2.50 v is t=1386.3sec
What is a capacitor, and what is its formula?The fundamental equation for capacitors is charge = capacitance x voltage. Q = C x V. It is the capacitance that holds one coulomb of charge per one volt (defined as the quantity of charge transferred by one amp in one sec) that is measured in farads.
What function does a capacitor serve?a capacitor is an electrical energy storage device that consists of two conductors that are isolated from one another and placed near to one another. A straightforward illustration of one such storage device is a parallel-plate capacitor.
To know more about capacitor visit :
https://brainly.com/question/29301875
#SPJ4
any circuit in which the current is split or follows two (or more) alternative paths is called a(n) ? circuit.
All of the parts of a series circuit are connected end to end to create a single path. All of the components in a parallel circuit are linked across one another to create precisely two sets of electrically coupled points.
Parallel circuits are where?
Parallel circuits make sure that various appliances continue to operate even while other appliances are off and keep the lights on in our houses. The most common type of circuit used in residential electrical wiring is a parallel circuit, which has several advantages over other types of circuits.
Why is parallel more efficient than series?
Numerous data bits are delivered over multiple channels at once when data is sent utilizing parallel data transmission. As a result, data can be transmitted significantly more quickly than with serial transmission techniques.
To know more about parallel circuits visit:
https://brainly.com/question/29708786
#SPJ4
a charged particle with a mass of m and a charge of q is injected midway between the plates of a capacitor that has a uniform electric field of e. what is the acceleration of this particle due to the electric field?
Eq/m is the particle's acceleration as a result of the electric field, as stated in the preceding sentence.
What is the principle behind a capacitor?To hold energies in an electrical circuit, a capacitor is a device. The idea behind how a capacitor functions is that if a earthed conductor is moved close to a conductor, its capacitance increases noticeably. In light of this, a capacitor consists of two plates with equal and opposing charges that are spaced apart.
Force is also ma, and the force acting upon that charge is qE. Acceleration a may be calculated by setting qE = ma.
Consequently a = Eq/m
To know more about Capacitor visit:
https://brainly.com/question/17176550
#SPJ4
What happens to the charge on the capacitor immediately after the switch is thrown?
A. The electrons on the negative plate of the capacitor are held inside the capacitor by the positive charge on the other plate.
B. Only the surface charge is held in the capacitor; the charge inside the metal plates flows through the resistor.
C. The electrons on the negative plate immediately pass through the resistor and neutralize the charge on the positive plate.
D. The electrons on the negative plate eventually pass through the resistor and neutralize the charge on the positive plate.
The charge on the capacitor immediately after the switch is thrown the correct option is (D). (The electrons on the negative plate eventually pass through the resistor and neutralize the charge on the positive plate.)
A capacitor is made up of two plates that are spaced apart and have opposing charges. When a switch is thrown in an RC circuit, electrons immediately begin to move from the negative plate to the positive plate. On the positive plate, the electrons neutralize after passing through the resistor. As a result, the plate ultimately changes and the process is repeated. Consequently, the appropriate choice is (D). (Eventually, the negative plate's electrons will flow through the resistor and balance the positive plate's charge.)
Learn more about Capacitor.
brainly.com/question/17176550
#SPJ4
a mountain climber is about to haul up a 15 m length of hanging rope. how much work w will it take if the rope weighs 2 newtons per meter?
When a mountain climber is preparing to draw up a 15 m length of hanging rope, the work required is W = 225 J if the rope weights 2 newtons per metre.
Find the force equation.
k =2 N/m.
15-x.
F(x) = kx
F(x) = 2(15-x)
interval of 0 to 15.
W = ∫₀¹⁵2(15-x) on the interval 0 to 15
W = 2(15x) - 2(x^2/2)
on the interval 0 to 15
W = 225 J
Work is the amount of energy delivered to an item by an external force when that force moves it a specific distance.
The quantity of energy delivered to an item through work is defined as work done on it.
You are conducting work on an item when you apply a force to it that causes its position to shift in the same direction as the force. The work done on an object is divided into two parts.
Learn more about Work here:
https://brainly.com/question/18094932
#SPJ4
based on these units, select any of the following expressions that could be valid expressions?
Hint 1. Consistent units The left-hand side and the right-hand side of any equation must have the same units. For example, only a quantity measured in meters can be equal to another quantity measured in meters. Just as you can't compare apples and oranges, you can't compare meters and seconds. To see it an equation is consistent, substitute in the units of all of the terms in the equation. If the two sides of the equation have the same units, the equation may express some valid physical relationship
o v=a/t
o t=3√d2/va
o d=at
o a=d/t2
o a=√vd/t3
o v=at
Yes, that is correct. Consistent units in an equation ensure that the equation expresses a valid physical relationship by ensuring that the units of measurement , the equation is considered consistent and may express a valid physical relationship.
Consistent units refers to the requirement that the units of measurement on both sides of an equation must be the same. This ensures that the equation expresses a valid physical relationship. In the examples provided, v=a/t, t=3√d2/va, d=at, a=d/t2, a=√vd/t3, and v=at all have consistent units, as the units on both sides of the equation are the same.
Learn more about consistent units here:
https://brainly.com/question/30156223
#SPJ4
hinking about the circular flow of income and the data you just analyzed, compose one well-written paragraph that shows how you can apply the circular flow of income
Answer:
Explanation:
to the data
The circular flow of income can be applied to the data by showing how the money from the transactions in the economy is cycled around the different parts of the economy. For example, the consumers spend money to purchase goods and services from businesses, which in turn provides income to the businesses and the employees who work for them. The income from the businesses and employees is then used to purchase goods and services from other businesses and households, creating a circular flow of income. This cycle is evident in the data and shows how the money from the different parts of the economy are interconnected.
Compare the pictures of the igneous rocks.
Which of the three rocks shows evidence of the longest cooling process?
this is science
The rock that shows evidence of the longest cooling process is typically granite. Granite is a type of intrusive igneous rock, which means that it formed from magma that cooled slowly beneath the Earth's surface.
What are dolerite and basalt?Dolerite and basalt are examples of extrusive igneous rocks, which formed from lava that cooled quickly on the Earth's surface. The rapid cooling process did not allow for the formation of large mineral crystals, resulting in a finer-grained texture.
Explain the term igneous rocks.Igneous rocks are rocks that form from the solidification of molten rock material, either below the Earth's surface or on the Earth's surface. The solidification process can occur slowly over a long period of time or quickly over a short period of time, depending on the conditions under which the molten rock solidifies.
To know more about rocks, visit here:
https://brainly.com/question/19930528
#SPJ1
Which is non-renewable energy source Mcq?
Nuclear power, natural gas, lignite, and oil are examples of nonrenewable energy sources. The difficulty for mankind is that once the resources are finite, they cannot be replenished.
What are 5 benefits of non renewable energy?Energy content of non-renewable materials is high. Compared to renewable energy sources like solar or wind, resources like coal and oil often provide us more energy. Coal mining, oil sales, and the building of pipelines for natural gas can all result in enormous riches.
Non-renewable energy: Is it harmful?Burning coal and oil can cause particulates to be released into the air, sea, and land. Many of these bits are discharged into the air, while some are captured and kept away. Fossil fuel burning also disrupts the "carbon budget" of the planet, which balances the amount of carbon in the atmosphere, ocean, and ground.
To know more about Non-renewable energy visit:
https://brainly.com/question/877821
#SPJ4
Three forces act on an object in vertical plane two forces of 500N and 300N act vertically upwards and the third force of 600N acts vertically downwards determine the resultant force acting on the object
The resultant force acting on the object is 200 N upwards.
What is the resultant force acting on the object?
The resultant force acting on the object is calculated by taking sum of all the forces including their direction.
Mathematically, the formula for the resultant force acting on the object is given as;
F ( net ) = F1 + F2 + F3
where;
F1 is the first force acting vertically upwardF2 is the second force acting vertically upwardF3 is the third force acting vertically downwardThe magnitude of the first force acting vertically upward = 500 N
The magnitude of the second force acting vertically upward = 300 N
The magnitude of the third force acting vertically downwards = 600 N
The resultant force acting on the object is calculated as follows;
F (net) = 500 N + 300 N - 600 N
F (net) = 200 N
Learn more about resultant force here: https://brainly.com/question/25239010
#SPJ1
four point charges have the same magnitude of 2.36 10-12 c and are fixed to the corners of a square that is 3.95 cm on a side. three of the charges are positive and one is negative. determine the magnitude of the net electric field that exists at the center of the square.
on either side, 0 cm Find the size of the net electromagnetic field present at the center of the square using three positive and one negative charges.
The meaning of magnitude?a substantial or significant amount
A man of ordinary means would have been discouraged by the task's size and importance (/maentud/). planetary science. Magnitude also describes how bright a star appears to be from Earth.
What is the physics magnitude?A picture of magnitude
Magnitude is a term used in physics to describe an object's maximal size and direction. Scalar and vector quantities both use magnitude as a common factor.
to know more about electromagnetic visite:
https://brainly.com/question/17057080
#SPJ4
two parallel conducting plates are separated by 12.0 cm, and one of them is taken to be at zero volts. (a) what is the magnitude of the electric field strength between them, if the potential 6.0 cm from the zero volt plate is 450 v?
The magnitude of the electric field strength between the two parallel conducting plates is 75 V/cm.
What is magnitude?
The magnitude of a quantity refers to the size or amount of that quantity, regardless of its direction. For example, the magnitude of velocity is the speed at which an object is moving, regardless of the direction it is moving in. Similarly, the magnitude of electric field is the strength of the field, regardless of the direction of the field.
To calculate the electric field strength between the two parallel conducting plates, we can use the formula:
E = V / d
where E is the electric field strength, V is the potential difference, and d is the distance between the plates.
Given that the potential 6.0 cm from the zero volt plate is 450 V, we can use this information to calculate the electric field strength between the plates:
E = 450 V / 6.0 cm = 75 V/cm
So the magnitude of the electric field strength between the two parallel conducting plates is 75 V/cm.
To learn more about magnitude from the given link:
https://brainly.com/question/24468862
#SPJ4
if a clay boat weighs .005 kg and is flisting, what is the upward force the water is exerting on the boat?
Answer: Force = 0.05N
Explanation: As the clay boat is floating therefore the upward force that the water is exerting on boat is equal to the weight of the boat, so they remain in vertical equilibrium⇒ net downward force = net upward force.
Mass of the boat (M) = 0.005 kg
Gravitational acceleration = 10 m/[tex]s^{2}[/tex]
Upward force = Weight of the boat = M×g = 0.005× 10 = 0.05 N
a light, inextensible cord passes over a light, frictionless pulley with a radius of 13 cm. it has a(n) 13 kg mass on the left and a(n) 4.8 kg mass on the right, both hanging freely. initially their center of masses are a vertical distance 3.3 m apart. the acceleration of gravity is 9.8 m/s 2 .at what rate are the two masses accelerating when they pass each other? answer in units of m/s 2 .
Answer in N-units. With their centers of mass 3.3 m apart vertically, a light, inextensible cable initially travels over a light, friction pulley with such a radius of 13 cm. .
The gravitational acceleration is 9.8 m/s 2. How quickly do the two masses accelerate when they pass one another?
At 1.2 m/s2, an elevator increases in speed.
Gravity accelerates at a rate of 9.8 m/s2.
What is the forward force that the elevator floor applies to a passenger weighing 86 kg
Answer in N-units.
when there is an upward acceleration in the elevator?
Take into account the usual force the elevator would exert on you: N = mg while the elevator is stationary or travelling at a constant speed. If the elevator is moving upward, N = mg + ma. If the elevator is accelerating downward, N = mg - ma.
to know more initially about visit : https://brainly.com/question/15396694
#SPJ4
3. choose two objects from the illustration. based on the scene, how might these objects be in motion and a reference point at the same time?
Motion is viewed as reliant on the observer's reference frame in special relativity theory (the frame which an observer uses for the description of of the observed phenomenon).
When observed from the guy standing's reference point of the Sun, the trees are in motion. The man standing as a point of reference for the passengers in the plane may observe that the airplane's wings are moving in relation to the trees. When an object's position in relation to its surroundings changes over time, it is said to be in motion. When an object is used to detect if another object is moving, it is referred to as a reference point. The trees are moving relative to each other, as viewed by the passengers in the aeroplane.
To learn more about motion click here https://brainly.com/question/22810476
#SPJ4
how to fix a problem with my poco m3 cell phone, can not here sound unless the microphone is set to on
There are a lot of things that could be causing the microphone on your phone to malfunction.
One or more of these issues could be caused by blockages in the microphone, an outdated piece of software, an unreliable third-party app, or faulty hardware. You should begin by determining whether or not the problem is indeed being caused by your microphone.
To begin, you can test the microphone on your phone by recording your voice using any of the recorders on your device. If the phone is able to record the sound of high quality, the microphone probably isn't broken. If everything is working well, you have nothing to worry about and can proceed with the next troubleshooting steps to repair the problem on your own.
1. Restart Your Mobile Device
2. Verify That the Microphone Is Covered by the Phone Protection
3. Verify the Existence of Connected Devices
4. A Microphone That Is Spotless
5. Eliminate All Third-Party Applications
6. Perform Software Updates
Want to know more about microphones visit the link which is given below;
https://brainly.com/question/12484674
#SPJ4
when the three blocks in the figure below are released from rest, they accelerate with a magnitude of 0.525 m/s2. block 1 has mass m, block 2 has 6m, and block 3 has 6m. what is the coefficient of kinetic friction between block 2 and the table?
If an automobile accelerates at a rate od a=2m/s2 a = 2, m/s2, it means that its velocity is changing at a rate of v=2m/s v = 2 m/s every second. It simply describes how the car's velocity relates to the car's own velocity.
What is the lower block's acceleration?We suppose that one block moves together to the right and left evenly in order to calculate the velocity of the bottom block. so, The velocity to the bottom block is twice that of the upper block when Newton's second law is simplified for both the upper and lower blocks together.
A block formula is what?The Calculator block evaluates an equation specified by the user and outputs the evaluation's outcome as a True/False, a number, or an output of an instrument type. Every time one of the connectors mentioned in the block's internal formula changes, the block calculates the total and outputs its value.
To know more about velocity visit :
https://brainly.com/question/18084516
#SPJ4
The heating element of an electric dryer is rated at 4.1 kW when connected to a 240 V line. (a) What is the current in the heating element? Is 12-gauge wire large enough to supply this current? (b) What is the resistance of the dryer's heating element at its operating temperature? (c) At 11 cents per kWh, how much does it cost per hour to operate the dryer?
The current in the heating element is 17.08 A, and 12-gauge wire is sufficient to supply this current. The resistance of the dryer's heating element at its operating temperature is 14.08 Ω.At 11 cents per kWh, it costs 0.41 cents per hour to operate the dryer.
What is current?Current is the flow of electric charge, usually through a conductor such as a wire. It is measured in amperes (A). Current is a measure of the rate of flow of electric charge, and can be direct (DC) or alternating (AC). In AC, the current regularly switches direction, making it ideal for powering most electrical equipment.
The current in the heating element is 4.1 kW/240 V = 17.1 A. 12-gauge wire is large enough to supply this current, as it can handle up to 20 A.
(b) The resistance of the dryer's heating element at its operating temperature can be calculated using Ohm's Law. R = V/I = 240 V/17.1 A = 14.03 Ω.
(c) The cost per hour to operate the dryer is 11 cents/kWh x 4.1 kW = 45.1 cents.
To know more about current click-
https://brainly.com/question/25922783
#SPJ4
A pair of 10-N vectors at right angles to each other has a resultant of about?
A. 10N. B. 14 N. C. 20 N. D. none of the above
The combination of two 10-N trajectories at perpendicularly is approximately 14 N.
What exactly are vectors, exactly?A quantity or phenomena with independent qualities for both size and direction is called a vector. The word can also refer to a quantity's mathematical or geometrical representation. Movement, momentum, force, electric interference, and weight are a few elements of axes in nature. To "transport" something from point A to point B, a vector is required; the Latin root of the word vector implies "carrier". Astronomers studying the planetary rotation around the Sun in the 18th century were the first to apply it.
Resultant vector [tex]$\vec{\gamma}$[/tex] can be written as
[tex]$$\begin{aligned}\vec{r} & =10 \hat{i}+10 \hat{\jmath} \mathrm{N} \\|\vec{r}| & =\sqrt{(10 \mathrm{~N})^2+(10 \mathrm{~N})^2} \\|\vec{\gamma}| & =10 \sqrt{2} \mathrm{~N} \\|\vec{r}| & =14.14 \mathrm{~N} \\|\vec{r}| & =14 \mathrm{~N}\end{aligned}$$[/tex]
To know more about Vectors visit:
https://brainly.com/question/29708786
#SPJ4
what is the mechanical work done by the cantilever when the extension increases from 10 nm to 15 nm?
It is shown graphically as the region between the respective data points on the force-extension graph. The correct answer from Figure 2 is [(100 - 0) 10-12]N [(15 - 10) 10-9]m/2 = 2.50 10-19 J.
Force divided by extension equals what?F = k e. When force (F) is expressed in newtons (N) The newtons per metre (N/m) unit of measure for spring constant (k) Extension (e), often known as lengthening, is expressed in metres (m).
What is displayed on a force-extension graph?An increase in applied stress causes a material to extend, as shown by a force-extension graph. The properties of the material can be determined and predicted using this method.
To know more about force-extension visit:
https://brainly.com/question/29091421
#SPJ4
how does the ma of a 6-m ramp compare with the ma of a 4-m ramp if both are used to load crates onto trucks that have cargo areas that are 1 m off the ground?
The 6 m ramp has greater mechanical advantage than 4 m ramp.
What is the velocity ratio of the ramp?
The velocity ratio of a ramp or inclined system is determined from the ratio of the distance travelled by the effort to the distance travelled by the load.
Mathematically, the formula for velocity ratio of the ramp is given as;
V.E = dE / dL
V.R = 1 / sinθ
where;
dE is the distance travelled by the effortdL is the distance travelled by the loadThe mechanical advantage of the ramp is calculated by the following formula.
M.A ∝ V.R
where;
θ is the angle between the foot of the ramp and horizontalsinθ = dE / dL
The mechanical advantage of the
For a ramp of 6m,
M.A = 1 / sinθ = 1 / ( 1 m / 6 m) = 6
For a ramp of 4 m,
M.A = 1 / sinθ = 1 / ( 1 m / 4 m ) = 4
Learn more about mechanical advantage here: https://brainly.com/question/25984831
#SPJ1
if you wish to store a large amount of energy in a capacitor bank, would you connect capacitors in series or parallel? explain.
It implies that as the capacitance value increases, so will the quantity of the energy. Therefore, the capacitors should be connected together in parallel in order to store more power in a capacitor bank.
What are the uses of a capacitor bank?Capacitors are used in the distribution of electric power to rectify power factor. These banks are required to offset inductive loading caused by components like electric motors & transmission lines, which causes the load to seem to be primarily resistive.
Where are the banks of capacitors?banks of distribution capacitors. Distribution capacitors are put in place at substations, on the poles, or adjacent to the load. Even though these capacitors units serve the local demand with reactive power, they might not be able to lower feeder & transformer losses.
To know more about capacitor bank visit:
https://brainly.com/question/12497095
#SPJ4
homework a light plane travels a distance of 150 m along a runway before takeoff. find the work done by the plane engine if it is applying a force of 13500 n. a horse pulls a carriage by applying 450 n of force. find the traveled distance if the horse did 89 kj of work. a truck travels at a constant speed of 45 m/s. how much work did the truck engine do during a 2 hour period if it supplied a force of 25 kn of force? airflow lifts a 3.6 kg bird 50 m up. how much work was done by the flow?
airflow lifts a 3.6 kg bird 50 m up. how much work was done by the flow is 2,025,000J.
What is the purpose of airflow?
Data pipelines or workflows are scheduled and coordinated using Apache Airflow. The management, sequencing, coordination, and scheduling of intricate data pipelines from several sources is referred to as orchestration of data pipelines.
Airflow: A Python or Not?
The platform for creating, planning, and managing batch-oriented workflows is called Apache Airflow. With the help of the Python framework of Airflow, you may create workflows that connect to almost any technology.
To know more about airflow visit:
https://brainly.com/question/18754989
#SPJ4
A bat emits a series of high-frequency sound pulses as it approaches a moth. The pulses are approximately 70.0 ms apart and each is about 3.0 ms long. How far away can the moth be detected by the bat, so that the echo from one chirp returns before the next chirp is emitted?
Answer:
The moth can be detected by the bat when it is about 21 meters away.
Explanation:
This is because the sound waves travel at about 340 meters per second, so it takes about 70 milliseconds for the sound waves to travel from the bat to the moth and back again.
Baed on your undertanding of behaviorim, how would a modern behaviorit be mot likely to tudy memory?
Behaviorism focuses on the idea that all behaviors are learned through interaction with the environment.
What is best definition of environment?Environment can be defined as a sum total of all the living and non-living elements and their effects that influence human life. While all living or biotic elements are animals, plants, forests, fisheries, and birds, non-living or abiotic elements include water, land, sunlight, rocks, and air.
What is environment and write its importance?An Environment is everything that is around us, which includes both living and nonliving things such as soil, water, animals and plants, which adapt themselves to their surroundings. It is nature's gift that helps in nourishing life on Earth.
To know more about environment visit
https://brainly.com/question/12163539
#SPJ4
pressure is question 3 options: a) cannot be determined using newton's second law. b) the rate change of time of momentum c) the rate change of time of momentum divided by area. d) none of the above
Pressure is the rate change of time of momentum divided by area. The correct answer is c.
Pressure is a measure of how much force is applied per unit area. It is defined as the rate of change of momentum of a fluid per unit area. This means that if a fluid is pushed against a surface, the pressure at that point is equal to the force exerted on the surface divided by the area of the surface.
Newton's second law of motion states that the force acting on an object is equal to the mass of the object multiplied by its acceleration, which is not directly related to pressure. Pressure is a scalar quantity and has no direction, it is a measure of how much a force is pushing or pulling in all directions.
To learn more about Newton law of motion visit: https://brainly.com/question/28171613
#SPJ4
how thick is the oil? suppose that the density of oil is 900 kg/m3.
The oil is 1 meter thick if the density of oil is 900 kg/m³ and it is kept in a cube shape container of 1 m³ volume.
The density of a substance is defined as the mass contained by the unit volume of the substance. In other words, density is the ratio of the mass and volume of a substance.
Density(d) = Mass(m)/volume(V)
Its SI unit is kg/m³.
If the density of oil is 900 kg/m³. And the volume of cube shaped container is 1 m³. V = 1 × 1 × 1 m³
So the depth would be 1 m³.
--The given question is incomplete, the complete question is
"How thick is the oil? suppose that the density of oil is 900 kg/m³, and it is kept in cube shaped container of 1 m³ volume.
To know more about density, here
https://brainly.com/question/29775886
#SPJ4
The current through inductance L is given by I = I0 sin ω t .
Find an expression for the potential difference ΔVL across the inductor.
Express your answer in terms of the variables L , ω , I0 , and t
ΔVL =
The maximum voltage across the inductor is 0.20 V when L =63μH and f =500kHz . What is I0 ?
I0 =
The value of I0 is 0.0000316 A. The current through inductance L is given by I = I0 sin ω t
What is the relationship between inductance and the frequency of an alternating current?Inductance and frequency have an inverse relationship, meaning that as the frequency of an alternating current increases, the inductance decreases and vice versa. This is because an inductor opposes changes in current, and as the frequency of the current increases, the rate of change in current also increases, making the inductor's opposition stronger.
The potential difference across an inductor is given by the derivative of the flux linkage concerning time. Since the flux linkage is given by Li, we have:
ΔVL = L dI/dt
Substituting the given expression for I:
ΔVL = L d/dt(I0 sin ωt)
= L I0 ω cos ωt
To find the maximum voltage across the inductor, we can take the derivative of this expression with respect to time and set it equal to zero:
d/dt(L I0 ω cos ωt) = 0
Since the cosine function has a maximum value of 1 at t = (2n+1)π/ω for any integer n, we can use this to find the maximum voltage:
L I0 ω = 0.2V
Given L = 63μH and f = 500kHz, we can find the angular frequency:
ω = 2πf = 2π(500 x 10^3) = 3.14 x 10^6
So,
I0 = 0.2V / (63 x 10^-6H * 3.14 x 10^6) = 0.0000316 A
To know more about Frequency visit:
brainly.com/question/5102661
#SPJ4
12
4bit) a kettle is rated at 1200w,
the resistance of the heating element is 11.5 ohms.
show, using your working out that the current flowing through the heating element is about
10a
(3 points
The current flowing through the heating element is about 104.35A.
What is Ohm's Law?Ohm's Law states that the current (I) flowing through a circuit is equal to the voltage (V) divided by the resistance (R).
I = V / R
We know the resistance of the heating element is 11.5 ohms. We can use the power rating of the kettle, which is 1200W, to calculate the voltage. Power is equal to voltage multiplied by current, so we can use this equation to find the voltage:
P = V * I
V = P / I
We can substitute the known values into this equation:
V = 1200 / I
Now we can use Ohm's Law to find the current:
I = V / R
Substituting the values we know:
I = (1200 / I) / 11.5
Solving for I, we get:
I = 104.35A
The current flowing through the heating element is about 104.35A.
To know more about Ohm's Law, visit:
brainly.com/question/1247379
#SPJ4
you produce successive resonant frequencies of 510, 850, and 1190 hz. (a) is the instrument an open-open pipe or an open- closed pipe? explain how you know. (b) what is the fundamental frequency?
The successive resonant frequency is the an open-open pipe instrument.
What is the formula for fundamental frequency?
The lowest frequency of a periodic waveform is known as the fundamental frequency, also known as just the fundamental. V = v/2l is the fundamental frequency (n = 1). Higher frequencies are multiples of the fundamental frequency and are referred to as harmonics or overtones. The fundamental is sometimes referred to as the first harmonic; n = 2 results in the second harmonic or first overtone, and so on.
Which pipe, an open pipe or a closed pipe, emits more harmonics?The basic tone and its peculiar harmonics can be produced via a closed pipe. But the fundamental tone as well as the odd and even harmonics can be produced by an open pipe. There are more individual tones in a note produced by an open pipe.
Learn more about resonant frequency here:
brainly.com/question/13191113
#SPJ4
