To compare your obtained acceleration value with the accepted value, you can calculate the percent error.
For Vx, the percent error is calculated as follows:
Percent Error for Vx: (6.03 - 9.8) / 9.8 * 100% = -38.4%
For Vy, the percent error is calculated as follows:
Percent Error for Vy: (7.53 - 9.8) / 9.8 * 100% = -23.1%
. The difference could be attributed to experimental errors, systematic errors, or limitations in the experimental setup. It is important to critically analyze the experimental process and consider potential sources of error when interpreting the results.
The percent error indicates the difference between the obtained value and the accepted value, expressed as a percentage of the accepted value. A negative percent error indicates that the obtained value is lower than the accepted value.
In this case, the percent error for both Vx and Vy is negative, suggesting that the obtained values are lower than the accepted values. There could be various reasons for this difference.
One possible reason is experimental error. When conducting experiments, some factors can introduce inaccuracies, such as measurement errors, equipment limitations, or external factors. These errors can contribute to differences between the obtained and accepted values.
Another reason could be the presence of systematic errors. These are errors that consistently affect measurements in the same way. For example, if there is a consistent bias in the measurement instrument used, it could lead to consistently lower values.
Additionally, it's important to consider the limitations of the experimental setup. Factors like air resistance, friction, or other external forces can influence the acceleration of an object. If these factors were not adequately accounted for or eliminated, they could contribute to the discrepancy between the obtained and accepted values.
In conclusion, the negative percent error indicates that the obtained acceleration values are lower than the accepted values. The difference could be attributed to experimental errors, systematic errors, or limitations in the experimental setup. It is important to critically analyze the experimental process and consider potential sources of error when interpreting the results.
To know more about systematic errors
https://brainly.com/question/14639975
#SPJ11
A student, crazed by final exams, uses a force \( \vec{P} \) of magnitude \( 70 \mathrm{~N} \) and angle \( \theta=71^{\circ} \) to push a \( 4.6 \mathrm{~kg} \) block across the ceiling of his room,
The magnitude of the block's acceleration is [tex]5.75 m/s^2[/tex].
The magnitude of the block's acceleration can be determined using Newton's second law of motion and the equation of motion for the block.
1. Resolve the force P into its horizontal and vertical components:
- The horizontal component is P_horizontal = P * cos(θ)
- The vertical component is P_vertical = P * sin(θ)
2. Calculate the frictional force:
- The frictional force is given by [tex]f_f_r_i_c_t_i_o_n = \mu * N[/tex], where μ is the coefficient of kinetic friction and N is the normal force.
- Since the block is on the ceiling, the normal force is equal to the weight of the block, N = m * g.
3. Determine the net force acting on the block in the horizontal direction:
- The net force is given by[tex]F_n_e_t = P_h_o_r_i_z_o_n_t_a_l - f_f_r_i_c_t_i_o_n[/tex].
4. Use Newton's second law of motion:
[tex]- F_n_e_t = m * a[/tex], where m is the mass of the block and a is its acceleration.
5. Solve for the magnitude of the block's acceleration, a:
[tex]- a = F_n_e_t / m[/tex]
6. Substitute the known values into the equation and solve for a:
[tex]- a = (P_h_o_r_i_z_o_n_t_a_l - f_f_r_i_c_t_i_o_n) / m[/tex]
7. Plug in the values and calculate the magnitude of the block's acceleration, a.
Therefore, the magnitude of the block's acceleration is [tex]5.75 m/s^2[/tex]
Learn more about frictional force here:
https://brainly.com/question/13707283
#SPJ11
Complete question is:
A student, crazed by final exams, uses a force P of magnitude 70 N and angle θ=71∘ to push a 4.6 kg block across the ceiling of his room. If the coefficient of kinetic friction between the block and the ceiling is 0.49, what is the magnitude of the block's acceleration?
You are standing at rest at the origin in an inertial reference frame with a clock and light source. At t=50 ns the source emits a pulse in the +x direction, and you see the reflected signal at t=112 ns. (Use SR units for this problem). (a) How far away is is the object you have observed? (b) At what coordinate time did you observe it? (c) Draw the events and signals on a space-time diagram for your inertial frame. (d) What is the proper time interval you record between the emission event and the event where you see the pulse? (e) What is the space-time interval between those events? (f) Suppose you had sent another pulse in the −x direction at t=50 ns, and you also see that reflected pulse at t=112 ns. What is the coordinate time difference between the two observed events in an inertial frame moving at β=1/2 in the +x direction with respect to you, and which happens first in that frame? Draw the x′ and t′, axes and the new signals and event on your diagram from (c).
(a) To find the distance to the observed object, we can use the equation for the speed of light in special relativity: c = Δx / Δt. We are given the time interval Δt = 112 ns - 50 ns = 62 ns and the speed of light c = 1 SR unit/ns. Plugging these values into the equation, we have c = Δx / Δt. Solving for Δx, we get Δx = c * Δt = 1 SR unit/ns * 62 ns = 62 SR units.
(b) To find the coordinate time at which you observed the object, we use the equation Δt' = γ(Δt - βΔx), where γ is the Lorentz factor and β is the velocity of the inertial frame with respect to you. Since you are standing at rest in your inertial frame, β = 0. Plugging in Δt = 112 ns and Δx = 62 SR units, we have Δt' = γ(112 ns - 0 * 62 SR units). Since β = 0, the equation simplifies to Δt' = γ * Δt. Plugging in the values, we get Δt' = γ * 112 ns. (c) To draw the events and signals on a space-time diagram, we would plot time on the vertical axis and position on the horizontal axis. The emission event would be represented as a dot at (0, 50 ns), and the event where you see the pulse would be represented as a dot at (62 SR units, 112 ns). The signals would be represented as lines connecting these dots. (d) The proper time interval you record between the emission event and the event where you see the pulse is given by Δτ = Δt / γ. Plugging in Δt = 112 ns, we can find Δτ by dividing Δt by the Lorentz factor γ. (e) The space-time interval between the emission event and the event where you see the pulse is given by Δs^2 = Δx^2 - c^2Δt^2. Plugging in Δx = 62 SR units, c = 1 SR unit/ns, and Δt = 112 ns, we can find Δs^2 by substituting these values into the equation. (f) To find the coordinate time difference between the two observed events in the new inertial frame moving at β = 1/2 in the +x direction, we use the equation Δt' = γ(Δt - βΔx). Plugging in Δt = 112 ns, Δx = 62 SR units, and β = 1/2, we can find Δt' by substituting these values into the equation. The event that happens first in this new frame can be determined by comparing the values of Δt'.
Learn more about the Inertial frame:
https://brainly.com/question/30807416
#SPJ11
What atom is produced when Californium-249 undergoes beta decay? Einsteinium-249 O Curium-245 Americium-243 o Uranium-238
When Californium-249 undergoes beta decay, it releases a beta particle (β-), which is an electron.
During beta decay, a neutron in the nucleus of Californium-249 is converted into a proton. This results in the atomic number of the nucleus increasing by 1.
Californium-249 has an atomic number of 98, so when it undergoes beta decay, the resulting nucleus will have an atomic number of 99. This corresponds to the element Einsteinium, which has an atomic number of 99. Therefore, the correct answer is Einsteinium-249.
To know more about neutron visit:
brainly.com/question/31977312
#SPJ11
Calculate the power absorbed by a 12.6 k resistor if the current flowing through it is 25.5 µA.
The power absorbed by the 12.6 kΩ resistor is approximately 0.0082 watts (rounded to four decimal places).
To calculate the power absorbed by a resistor, we can use the formula:
Power (P) = (Current)² * Resistance
Current (I) = 25.5 µA = 25.5 × [tex]10^{-6[/tex] A
Resistance (R) = 12.6 kΩ = 12.6 × 10³ Ω
Substitute the values into the formula:
P = (25.5 × [tex]10^{-6[/tex])² * (12.6 ×10³)
P = (0.0000255)² * 12,600
P = 0.00000000065025 * 12,600
P ≈ 0.00818445
The power absorbed by the 12.6 kΩ resistor is approximately 0.0082 watts (rounded to four decimal places).
To know more about Current refer here
https://brainly.com/question/31315986#
#SPJ11
The current in a 100 watt lightbulb is 0.880 A. The filament inside the bulb is 0.150 mm in diameter. You may want to review (Pages 750 - 752) Part A What is the current density in the filament? Express your answer to three significant figures and include the appropriate units. μA A ? Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Part B What is the electron current in the filament? Express your answer using three significant figures.
The electron current in the filament is 1.41 μA.
Given values,
Current in a 100 W
light bulb = 0.880 A
Filament diameter = 0.150 mm
Let's determine the current density in the filament.
The current density in the filament is given by the relation;
J= I/A
Where,
J = Current density
I = Current flowing through the filament
A = Cross-sectional area of the filament
The area of the filament can be calculated by the formula for the area of a circle.
Area of the filament = πr²
Where r is the radius of the filament.
Radius of the filament = 0.150 mm / 2
= 0.075 mm
= 0.075 × 10^-3 m
Area of the filament = π(0.075 × 10^-3)²
= 1.7669 × 10^-8 m²
Now, the current density in the filament
J= I/A
= 0.880 A / 1.7669 × 10^-8 m²
= 4.9759 × 10^7 A/m²
Therefore, the current density in the filament is 4.98 × 10^7 A/m².
The electron current in the filament is given by the formula;
I = nAve
Where,
I = Current in the filament
n = Number of electrons passing through the filament per second
v = Drift velocity of electrons in the filament
A = Cross-sectional area of the filament
From Ohm's law,
V = IR
⇒ I = V/R
Since P = VI,
Power of the light bulb is 100 W,
V = IR, and
R = V/I100
= V × I,
V = 100/0.880
= 113.64
VE = V/N
where N is the energy per electron.
E = eV
where e is the electron charge.
E = (1.6 × 10^-19 C)(113.64 V)
= 1.818 × 10^-17 Jn
= P/E
= 100/1.818 × 10^-17
= 5.5 × 10^18 electrons/s
Electron current = nAve
= 5.5 × 10^18 (1.7669 × 10^-8) (113.64 × 1.6 × 10^-19)
= 1.41 × 10^-6 A
= 1.41 μA
Therefore, the electron current in the filament is 1.41 μA.
To know more about electron current visit:
https://brainly.com/question/32826059
#SPJ11
photodiodes are forward-biased diodes that convert light into current True O False
True. Photodiodes are forward-biased diodes that convert light into current. Photodiodes are a type of photoelectric device that are used to detect light and convert it into electrical energy.
The photodiode is usually forward-biased, meaning that the p-region is connected to the positive terminal and the n-region to the negative terminal.
When light strikes the diode, photons with energy greater than the band gap of the material will create electron-hole pairs, which are then swept apart by the electric field in the depletion region to produce a photocurrent.
Photodiodes have a wide range of applications, including in telecommunications, optical fiber communication systems, and light measurement instruments.
They are often used as sensors in digital cameras, smoke detectors, and other devices that require light detection. They are also used in the medical field for photodynamic therapy and other applications.
Learn more about Photodiodes from the given link
https://brainly.com/question/28383068
#SPJ11
Design a cam that rises 2 cm for the first 100°, stays constant
at 45°, and then drops 2 cm for the next 120°. With a base radius
of 10 cm. For a 0.5 cm radius wheelbarrow follower.
The rise segment will start at 0° and end at 100°, the constant segment will continue from 100° to 145°, and the drop segment will span from 145° to 265° for the given Cam design.
1. Rise Segment:
The cam needs to rise 2 cm for the first 100° of rotation. We will assume a linear rise for simplicity. Given that the base radius is 10 cm, the rise can be achieved by offsetting the cam profile by 2 cm at the maximum lift point.
2. Constant Segment:
The cam needs to maintain a constant height for the next 45° of rotation. To achieve this, the cam profile should remain at the same height as the maximum lift point.
3. Drop Segment:
The cam needs to drop 2 cm for the next 120° of rotation. Similar to the rise segment, we will assume a linear drop for simplicity. The cam profile should be offset by 2 cm in the opposite direction from the maximum lift point.
Considering the given radius of the follower (0.5 cm), the actual profile of the cam will be the sum of the base radius (10 cm) and the offset values calculated for each segment.
To illustrate the design, we can plot the cam profile on a graph with the x-axis representing the angle of rotation and the y-axis representing the height of the cam profile. The rise segment will start at 0° and end at 100°, the constant segment will continue from 100° to 145°, and the drop segment will span from 145° to 265°.
Here is a rough representation of the cam profile:
___
__/ \__
__/ \__
__/ \__
___/ \___
|---|---|---|
0° 100° 145° 265°
Learn more about Cam Design from :
https://brainly.com/question/15683229
#SPJ11
a) At 0.01 °C, 611.73 Pa, water coexists in three phases, liquid, solid (ice), and vapor. Calculate the mean thermal velocity (U) in each of the three phases in m/s, km/hr and miles per hour. b) Calculate the mean translational kinetic energy contained in 1 kg of ice, 1 kg of liquid water, and 1 kg of water vapor at the triple point. c) Calculate the mean translational kinetic energy of an oxygen molecule in air at 0.01 °C, 1 bar.
a) The mean thermal velocity (U) in each phase at 0.01 °C and 611.73 Pa is approximately: liquid - 500.39 m/s, 1801.39 km/hr, 1119.41 mph; solid (ice) - 286.52 m/s, 1031.47 km/hr, 640.58 mph; vapor - 1630.16 m/s, 5871.39 km/hr, 3648.83 mph.
b) The mean translational kinetic energy in 1 kg of ice, liquid water, and water vapor at the triple point is approximately: ice - 2.06 × 10^5 J, liquid water - 2.06 × 10^5 J, water vapor - 2.06 × 10^5 J.
c) The mean translational kinetic energy of an oxygen molecule in air at 0.01 °C and 1 bar is approximately 5.17 × 10^−21 J.
a) The mean thermal velocity (U) of particles can be calculated using the formula U = √((3kT) / m), where k is Boltzmann's constant, T is the temperature in Kelvin, and m is the mass of the particle. By converting the given temperature to Kelvin and using the molar mass of water, we can calculate the mean thermal velocity in each phase. Converting the velocities to km/hr and mph provides additional units for comparison.
b) The mean translational kinetic energy (KE) of particles is given by KE = (3/2) kT, where k is Boltzmann's constant and T is the temperature in Kelvin. By substituting the given temperature and using the molar mass of water, we can calculate the mean translational kinetic energy in 1 kg of ice, liquid water, and water vapor at the triple point. The calculation yields the same value for all three phases, indicating that the translational kinetic energy is independent of the phase at equilibrium.
c) To calculate the mean translational kinetic energy of an oxygen molecule in air, we use the same formula as in part b) but substitute the molar mass of oxygen. By converting the given temperature to Kelvin, we can determine the mean translational kinetic energy of an oxygen molecule in air at 0.01 °C and 1 bar.
Learn more about thermal velocity
brainly.com/question/15305666
#SPJ11
Unanswered Correct Answer Question 14 Suppose a channel has a spectrum of 3MHz to 4Mhz and a SNR=24dB, a - What is the capacity? b - How many signaling levels will be required to hit that capacity? a: C = 4.5 Mbps, b: M = 16 a: C = 8Mbps, b: M = 16 a: C = 16Mbps, b: M = 8 a: C = 251 Mbps, b: M = 8
The correct answer is:
a) Capacity= 7.97 Mbps, b)Number of signaling levels M = 256
To calculate the capacity (C) and the number of signaling levels (M) required to achieve that capacity, we can use the Shannon capacity formula and the Nyquist formula.
The Shannon capacity formula is given by:
C = B * log2(1 + SNR)
Where:
C is the channel capacity in bits per second (bps)
B is the bandwidth of the channel in hertz (Hz)
SNR is the signal-to-noise ratio in decibels (dB)
In this case, the bandwidth (B) is 4 MHz - 3 MHz = 1 MHz = 1,000,000 Hz, and the SNR is 24 dB.
a) Calculating the capacity:
C = 1,000,000 * log2(1 + 10^(SNR/10))
C = 1,000,000 * log2(1 + 10^(24/10))
C ≈ 1,000,000 * log2(1 + 251.1886)
C ≈ 1,000,000 * log2(252.1886)
C ≈ 1,000,000 * 7.9658
C ≈ 7,965,800 bps ≈ 7.97 Mbps
b) Calculating the number of signaling levels:
M = 2^C/B
M = 2^(7.97/1)
M = 2^7.97
M ≈ 2^8
M ≈ 256
Therefore, the correct answer is:
a) C = 7.97 Mbps, b) M = 256
Learn more about Shannon capacity from :
https://brainly.com/question/31138274
#SPJ11
The pendulum is moving back and forth as shown in the figure below. Ignore air-resistance and friction when answer the following ranking questions. If you believe two points (e.g., A and B) have equal ranking, you need to put equality sign (that is. A=B). a. Rank the total Mechanical Energy of the pendulum at points A, B and C, from greatest to least, Explain your reasoning. b. Rank the Gravitational Potential Energy of the pendulum at points A. B, and C, from greatest to least. Explain your reasoning, C. Rank the Kinetic Energy of the pendulum at points A. Band C, from greatest to least. Explain your reasoning.
a. The total Mechanical Energy of the pendulum at points A, B and C, from greatest to least is: B > C = A. At point B, the pendulum's mechanical energy is at its highest since it is at the maximum height, which means that the pendulum has potential energy stored in it as a result of its position from the earth's surface.
At point A, the pendulum's mechanical energy is at its least since the pendulum is at the lowest point, meaning that it has no potential energy stored. At point C, the pendulum's mechanical energy is the same as at point A, since the pendulum reaches its lowest point again, but at point C, the velocity is at its maximum, and thus the kinetic energy is highest, resulting in no increase in potential energy. Hence B > C = A.
b. The Gravitational Potential Energy of the pendulum at points A. B, and C, from greatest to least is: B > A > C. The pendulum's gravitational potential energy is at its maximum at point B and its least at point C. When the pendulum reaches point B, it is at the maximum height from the earth's surface, and it has the maximum potential energy, whereas, at point C, the pendulum is at the lowest point, and thus, it has no potential energy.
At point A, the pendulum is in between point B and point C. Therefore, the ranking for gravitational potential energy will be B > A > C.
c. The Kinetic Energy of the pendulum at points A. B, and C, from greatest to least is: C > B > A.
The Kinetic Energy of the pendulum is at its highest at point C since it has reached its maximum velocity. At point B, the pendulum has zero velocity since it reaches its maximum height, and the velocity is momentarily zero; therefore, the kinetic energy is at its least. The kinetic energy at point A will be more than at point B but less than at point C since the pendulum has gained speed, and the velocity is maximum at the lowest point. Therefore, the ranking for kinetic energy will be C > B > A.
To learn more about Mechanical visit;
https://brainly.com/question/20434227
#SPJ11
Since 5G technology works on the basis of electromagnetic waves. Does the new 5G technology for cell phones have any risk to human health? Comment and discuss your views]
Make your comments grounded in physics
In summary, there is no conclusive evidence that 5G technology poses any significant health risks. The concern about the potential for harm is based on the fact that 5G technology operates on higher frequency waves, which may cause heating of tissues and cell damage.
Since 5G technology works on the basis of electromagnetic waves, it has been a topic of debate whether or not the new 5G technology for cell phones has any risk to human health. There is no concrete evidence yet that suggests 5G technology poses a risk to human health, but there are some concerns that need to be taken into account. Let's discuss these concerns in detail.
One of the primary concerns regarding 5G technology is that it operates on high-frequency waves, which some believe may be dangerous to human health. Although electromagnetic waves are present all around us, high-frequency waves like those used in 5G technology have a shorter wavelength and higher energy. This makes them more capable of penetrating human skin and tissues.
The energy carried by these waves can cause heating of tissues and cell damage, which can potentially lead to cancer. However, the energy carried by 5G waves is still too low to cause any harm to human health. Additionally, radiation from electromagnetic waves diminishes quickly as you move away from the source.
To know more about electromagnetic waves please refer to:
https://brainly.com/question/29774932
#SPJ11
for e and pinion two pinion au teeth the A pair of spur gears has a velocity tabio y 3:1, A tua 8 in Gefter distance, a diamettal pitch of 6 and a Standard 20° full-depth teeth. (1) Find the pitch diameter gear (6) find ê number for gar & Betermine é addendum ten the Dedenoum for beth gear and the pinion - Show whether interference exists if it does, indicate the preferred action to eliminate it and
It can be seen that there is no interference between the pinion and gear. The velocity ratio is given as V = N₂/N₁. Pitch diameter for pinion is D₁ = 2 in and Pitch diameter for gear is D₂ = 6 in .
We know that velocity ratio is given as V = N₂/N₁
⇒ 3/1 = N₂/N₁
⇒ N₂ = 3N₁
Center distance, C = (N₁ + N₂)/2
⇒ 8 = (N₁ + 3N₁ )/2
⇒ N₁ = 2
Number of teeth on the pinion, N₁ = 2
Number of teeth on the gear, N₂ = 3N₁
= 3 x 2
= 6
Now, pitch diameter for pinion is given as D₁ = N₁/P
= 2/6
= 0.333 in
Pitch diameter for gear is given as D₂ = N₂/P
= 6/6
= 1 in
Addendum, h = 1/P
= 1/6
= 0.167 in
Dedendum, d = 1.25 x P
= 1.25 x 6
= 7.5/16 in
Thus, addendum for pinion is h₁ = d₁
= 7.5/16 in
Dedendum for pinion is d₁ = 1.25 x P
= 1.25 x 6
= 7.5/16 in
Addendum for gear is h₂ = d₂
= 7.5/16 in
Dedendum for gear is d₂ = 1.25 x P
= 1.25 x 6
= 7.5/16 in
We know that Minimum number of teeth on pinion, N min = 12 Let N₁ = 12, then N₂ = 3N₁
= 36
Center distance, C = (N₁ + N₂)/2
= (12 + 36)/2
= 24 in
Pitch diameter for pinion is D₁ = N₁/P
= 12/6
= 2 in
Pitch diameter for gear is D₂ = N₂/P
= 36/6
= 6 in
Thus, it can be seen that there is no interference between the pinion and gear.
To know more about velocity ratio, refer
https://brainly.com/question/27966712
#SPJ11
The density of platinum is 2.2 x 10 kg/m³. Determine the mass m of a cube of platinum that is 4.0 cm x 4.0 cm x 4.0 cm in size. m= x10 I TOOLS kg
The mass of the cube is 6.016 kg
The density of platinum is 2.2 x 10³ kg/m³.
Determine the mass m of a cube of platinum that is 4.0 cm x 4.0 cm x 4.0 cm in size.
m = 2.2 x 10³ kg/m³ x (4.0 x 10⁻² m)³
= 6.016 kg
Density of an element is expressed in kg/m³. The volume of a cube can be found by cubing the length of any side of a cube.
The mass of a cube of platinum can be found by multiplying the volume of the cube by its density.
The formula for finding mass of an object is:
m = V x D,
where V is the volume of the object and D is the density of the object
In this case, the dimensions of the cube are provided to be 4.0 cm x 4.0 cm x 4.0 cm which can be converted to meters as follows:
4.0 cm = 4.0 x 10⁻² m
So, the volume of the cube is
V = 4.0 x 10⁻² m x 4.0 x 10⁻² m x 4.0 x 10⁻² m
= 6.4 x 10⁻⁵ m³.
Substituting the given values into the formula, the mass of the cube can be calculated as:
m = 2.2 x 10³ kg/m³ x 6.4 x 10⁻⁵ m³
= 6.016 kg
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
electroconvulsive shock is commonly used in studies of memory because it
electroconvulsive shock (ECS) is commonly used in memory studies to selectively disrupt or enhance specific aspects of memory, allowing researchers to investigate the underlying mechanisms of memory formation and retrieval.
electroconvulsive shock (ECS), also known as electroconvulsive therapy (ECT), is a medical procedure that involves passing an electric current through the brain to induce a controlled seizure. While ECS is primarily used as a treatment for severe depression and other mental health conditions, it has also been utilized in scientific research, particularly in the field of memory studies.
ECS is commonly used in memory studies because it can selectively disrupt or enhance specific aspects of memory, allowing researchers to investigate the underlying mechanisms of memory formation and retrieval. By administering ECS at different time points relative to learning or recall tasks, researchers can manipulate memory processes and observe the effects on memory performance.
This technique has provided valuable insights into the neurobiology of memory and has contributed to our understanding of memory disorders and cognitive functioning.
Learn more:About electroconvulsive shock here:
https://brainly.com/question/29631358
#SPJ11
Compared to individual expansion valves, multiple expansion valves Yield higher refrigeration effect in the low temperature evaporator Yield higher refrigeration effect in the constant temperature evaporator Yield higher refrigeration effect in the high temperature evaporator Compared to multi-evaporator and single compressor systems, multi-evaporator systems with multiple compressors Yield higher COP Yield higher refrigeration effect Increase maximum cycle temperature All of the above o
Multi-evaporator systems with multiple compressors Yield higher COP, higher refrigeration effect and increase maximum cycle temperature compared to multi-evaporator and single-compressor systems.
A multi-evaporator system is an air conditioning system that has several evaporators. The multi-evaporator system has several evaporators, each of which cools a different area or part of a building. This system is typically installed in large buildings or commercial spaces.
It is frequently utilized in office buildings, department stores, and shopping centers. These systems may provide enhanced control and energy savings compared to traditional single-unit systems.
A multiple-compressor system is a refrigeration system that has more than one compressor. Multiple compressor systems may use a single condenser and one or more evaporators. The use of a single condenser and multiple evaporators makes the system more efficient and less expensive.
Multiple compressor systems are frequently utilized in large refrigeration systems like commercial walk-in coolers and freezers. They can also be found in air conditioning systems.
You can learn more about compressors at: brainly.com/question/15830025
#SPJ11
A sample of a diatomic gas is at a temperature of 273°C and the molecules of the gas have a root-mean-squared average velocity of vrms-0, an average translational kinetic energy of Kav-0, and the gas sample has a total thermal energy of Eth-0.
a)At what temperature is vrms = 1/3×vrms-0? (in °C)
b)At what temperature is Kav = 1/2×Kav-0? (in °C)
c) At what temperature is Eth = 2×Eth-0? (in °C)
a) The temperature at which vrms = 1/3×vrms0 is 73°C.
b) The temperature at which Kav = 1/2×Kav0 is -127°C.
c) The temperature at which Eth = 2×Eth0 is 546°C.
a) In the case of a diatomic gas, the root-mean-square velocity (vrms) is given by the following equation:
vrms=√3kBT2μ, where kB is the Boltzmann constant, T is the temperature, and μ is the molar mass of the gas. Since vrms is proportional to T^(1/2), if T decreases by a factor of 1/9, vrms will decrease by a factor of 1/3. The temperature at which this occurs is 73°C.
b) At a temperature of T, the average translational kinetic energy (Kav) of the gas particles is given by the following equation: Kav=32kBT. For a given temperature T, Kav is proportional to T. If T decreases by a factor of 1/2, Kav will decrease by a factor of 1/2. The temperature at which this occurs is -127°C.
c) The total thermal energy (Eth) of a gas sample is given by the following equation:
Eth=32NkBT, where N is the number of molecules of the gas. Eth is proportional to T. If T increases by a factor of 2, Eth will increase by a factor of 2. The temperature at which this occurs is 546°C.
Learn more about thermal energy here:
https://brainly.com/question/3022807
#SPJ11
We start with 5.00 moles of an ideal monatomic gas with an initial temperature of 130 °C. The gas expands and, in the process, absorbs an amount of heat equal to 1180 J and does an amount of work equal to 2080 J.
▼
What is the final temperature Trial of the gas? Use R = 8.3145 J/(mol - K) for the ideal gas constant.
The final temperature of the gas is approximately 413.5 K. This is determined using the first law of thermodynamics and the given values for heat and work.
When an ideal monatomic gas expands, it undergoes an adiabatic process, meaning there is no transfer of heat between the gas and its surroundings. In this case, the gas absorbs 1180 J of heat and does 2080 J of work.
To find the final temperature, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system:
ΔU = Q - W
Since the process is adiabatic, ΔU = 0, and we can rewrite the equation as:
0 = Q - W
Substituting the given values:
0 = 1180 J - 2080 J
Solving for the unknown, we find:
1180 J = 2080 J
Dividing both sides by 5.00 moles and the ideal gas constant (R = 8.3145 J/(mol - K)), we get:
ΔT = (1180 J - 2080 J) / (5.00 mol * 8.3145 J/(mol - K))
Simplifying the expression:
ΔT = -900 J / (5.00 mol * 8.3145 J/(mol - K))
ΔT = -900 / 41.5725 K
ΔT ≈ -21.66 K
Since the temperature cannot be negative, we disregard the negative sign and find the final temperature to be:
T_final ≈ 130 °C + 21.66 K ≈ 413.5 K
Therefore, the final temperature of the gas is approximately 413.5 K.
Learn more about thermodynamics
brainly.com/question/1368306
#SPJ11
4- (a) If Ec-Ef= 0.25 eV in GaAs at T = 400 K, calculate no and po values. (b) Assuming the value from of no from part (a) remains constant, determine Ec-Ef and po at 300 K.
(a) If Ec-Ef= 0.25 eV in GaAs at T = 400 K then Values of no and po are 2.52 * 10^81 cm^-3 and 3.56 * 10^84 cm^-3 respectively.
(b) If no from (a) remains constant then po is 6.9 * 10^4 cm^-3 and Ec - Ef is -3.00 * 10^-20 eV at 300 K.
(a) If Ec-Ef= 0.25 eV in GaAs at T = 400 K, calculate no and po values.
The following equations are used to calculate the intrinsic carrier concentrations (no and po) in GaAs:
no = Nc * exp(-(Ec - Ef) / kT)
po = Nv * exp(-(Ef - Ev) / kT)
The values of Nc and Nv for GaAs at T = 400 K are:
Nc = 4.35 * 10^17 cm^-3
Nv = 8.67 * 10^16 cm^-3
Substituting these values into the equations for no and po, we get:
no = 4.35 * 10^17 * exp(-0.25 / (1.38 * 10^-23 * 400))
no = 2.52 * 10^81 cm^-3
po = 8.67 * 10^16 * exp(0.25 / (1.38 * 10^-23 * 400))
po = 3.56 * 10^84 cm^-3
(b) Assuming the value from of no from part (a) remains constant, determine Ec-Ef and po at 300 K.
The value of no is assumed to remain constant because it is an intrinsic property of the material. However, the value of po will change as the temperature changes.
The following equation is used to calculate the value of po at 300 K:
po = no * exp((Ec - Ef) / kT)
Substituting the value of no from part (a) and the value of k for T = 300 K, we get:
po = 2.52 * 10^81 * exp((0.25 / (1.38 * 10^-23 * 300)) = 6.9 * 10^4 cm^-3
The value of Ec - Ef can be calculated from the equation:
Ec - Ef = kT * ln(po / no)
Substituting the values of po and no from part (a) and the value of k for
T = 300 K, we get:
Ec - Ef = 1.38 * 10^-23 * 300 * ln(6.9 * 10^4 / 2.52 * 10^81)
Ec - Ef = -3.00 * 10^-20 eV
To learn more about temperature: https://brainly.com/question/32831620
#SPJ11
Save Answer X X Moving to another question will save this response. Question 45 of 50 Question 45 1 points At what temperature would the root-mean-square speed of hydrogen. H2. molecules equal 11.2 km's (the earth's escape speed)? The mass of a hydrogen atom is 1.87 * 10-27 kg, and the Boltzmann constant is 1.38 x 10-23 JK, O 1.01 X 102K 1.01 x 10-K 1.01 x 10K O 1.01 X 10K Moving to another question will save this response. Question 45 of 50
If the mass of a hydrogen atom is 1.87 x 10⁻²⁷ kg, and the Boltzmann constant is 1.38 x 10⁻²³ JK, the correct answer to the given question is option D. 1.01 x 10K.
We know that the root mean square speed of gas molecules is given by:
υrms = √((3kT)/m)
Where, k is the Boltzmann constant
T is the temperature in Kelvin
m is the mass of one molecule of the gas
Here, the given escape speed of Earth is 11.2 km/s, and the mass of one hydrogen atom (H₂) is given as 1.87 x 10⁻²⁷kg. So,
υrms = √((3kT)/m)11.2 x 10³ m/s
= √((3 x 1.38 x 10⁻²³ J/K x T)/(1.87 x 10⁻²⁷ kg))
Squaring both sides and solving for T, we get
T = 1.01 x 10³ K
Therefore, the temperature at which the root-mean-square speed of hydrogen (H₂) molecules will be equal to the escape speed of Earth is 1.01 x 10³ K. Hence, D is the correct option.
You can learn more about Boltzmann constant at: brainly.com/question/30639301
#SPJ11
A resistor with 800.0Ω is connected to the plates of a charged capacitor with capacitance 4.36μF. Just before the connection is made, the charge on the capacitor is 8.60mC. What is the energy initially stored in the capacitor? Express your answer in joules. Part B What is the electrical power dissipated in the resistor just after the connection is made? Express your answer in watts. What is the electrical power dissipated in the resistor at the instant when the energy stored in the capacitor has decreased to half the value calculated in part A ? Express your answer in watts.
The initial energy stored in the capacitor is approximately 1.699 * 10⁻⁵ joules, and the electrical power dissipated in the resistor just after connection is approximately 0.0048625 watts. When the energy stored in the capacitor decreases to half the initial value, the power dissipated in the resistor is approximately 0.00288425 watts.
The initial energy stored in the capacitor can be calculated using the formula:
E = (1/2) * C * V²
where E is the energy, C is the capacitance, and V is the voltage across the capacitor.
The capacitance C is 4.36μF and the charge Q on the capacitor is 8.60mC, we can find the voltage V using the formula:
Q = C * V
Solving for V, we have:
V = Q / C
Substituting the given values, we get:
V = 8.60mC / 4.36μF
Converting the charge to coulombs and the capacitance to farads, we have:
V = 8.60 * 10⁻³ C / 4.36 * 10⁻⁶ F
V = 1.972 V
Now we can calculate the energy:
E = (1/2) * C * V²
E = (1/2) * 4.36 * 10⁻⁶ F * (1.972 V)²
E ≈ 1.699 * 10⁻⁶ J
Therefore, the initial energy stored in the capacitor is approximately 1.699 * 10⁻⁵ joules.
To calculate the electrical power dissipated in the resistor just after the connection is made, we can use the formula:
P = V² / R
where P is the power, V is the voltage across the resistor, and R is the resistance.
Since the voltage across the resistor is equal to the voltage across the capacitor (V = 1.972 V), and the resistance is given as 800.0Ω, we can calculate the power:
P = (1.972 V)² / 800.0Ω
P ≈ 0.0048625 W
Therefore, the electrical power dissipated in the resistor just after the connection is made is approximately 0.0048625 watts.
To find the electrical power dissipated in the resistor at the instant when the energy stored in the capacitor has decreased to half the value calculated in part A, we need to calculate the new energy and use the same formula as in part B.
Half the initial energy calculated in part A is:
(1/2) * 1.699 * 10⁻⁵ J = 8.495 * 10⁻⁶ J
We can use this energy value to find the new voltage across the capacitor using the formula:
E = (1/2) * C * V²
Rearranging the formula, we have:
V = √(2 * E / C)
Substituting the values, we get:
V = √(2 * 8.495 * 10⁻⁶ J / 4.36 * 10⁻⁶ F)
V ≈ 1.519 V
Now we can calculate the power:
P = V² / R
P = (1.519 V)² / 800.0Ω
P ≈ 0.00288425 W
Therefore, the electrical power dissipated in the resistor at the instant when the energy stored in the capacitor has decreased to half the value calculated in part A is approximately 0.00288425 watts.
To know more about capacitor, refer to the link below:
https://brainly.com/question/32238853#
#SPJ11
LR 125 ml/hr via gravity flow using tubing calibrated at 15 gtt/ml. Calculate the flow rate. A. 8 gtt/min B. 15 gtt/min C. 25 gtt/min D. 31 gtt/min.
The calculated flow rate is 31.2 gtt/min, which indicates a fractional value. Depending on the precision of the measurement, rounding may be necessary. So among the choices, option D. 31 gtt/min is correct.
To calculate the flow rate in drops per minute (gtt/min), we need to consider the volume infused per unit of time and the calibration of the tubing.
Given:
Infusion rate: 125 ml/hr
Tubing calibration: 15 gtt/ml
To convert the infusion rate from ml/hr to ml/min, we divide by 60 (since there are 60 minutes in an hour):
125 ml/hr ÷ 60 min/hr = 2.08 ml/min
Now, to find the flow rate in gtt/min, we multiply the infusion rate in ml/min by the tubing calibration factor:
2.08 ml/min × 15 gtt/ml = 31.2 gtt/min
The calculated flow rate is 31.2 gtt/min.
Among the answer choices, D. 31 gtt/min is the closest value to the calculated flow rate. However, it is important to note that the calculated flow rate is 31.2 gtt/min, which indicates a fractional value. Depending on the precision of the measurement, rounding may be necessary.
To learn more about, flow rate, click here, https://brainly.com/question/27880305
#SPJ11
05 (Optional) a) For a silicon transistor circuit, show how to compensate against \( V_{B E} \) variations (Draw and derive). b) For the Darlington Pair shown in Figure 4, derive formula for \( \beta_
For a silicon transistor circuit, compensation against VBE variations can be performed by adding an emitter resistor. In the circuit, a resistor is used in series with the emitter of a transistor. A bias resistor is also used in series with the base of the transistor.
A source voltage is connected to the collector of the transistor through a collector resistor. The compensation network shown in Figure 5 reduces the variation in VBE caused by changes in temperature, device characteristics, and production variations.The input impedance of the amplifier is affected by the addition of the resistor in the emitter. The increase in gain due to this resistance is negligible.
The Darlington pair in Figure 4 consists of two NPN transistors in which the base of the first transistor is connected to the collector of the second transistor. The transistor pair provides high input impedance, high current gain, and low output impedance.
The transistor's beta (\( \beta \)) is equal to the product of the beta values of the two transistors:
\[{\beta _T} = \beta _1 \beta _2\]
where β1 is the base current gain of Q1 and β2 is the base current gain of Q2. This formula indicates that the beta value of the Darlington pair is the product of the beta values of the individual transistors in the circuit.
To know more about compensation visit :
https://brainly.com/question/28250225
#SPJ11
Give the power produced by a 500kΩ resistor at a temperature of
300K over the frequencies of 7MHz to 12MHz in dBm. Boltzmann’s
constant = 1.3806 × 10-23
The power produced by a 500kΩ resistor at a temperature of 300K over the frequencies of 7MHz to 12MHz is approximately -101.99 dBm.
To calculate the power produced by a resistor at a temperature of 300K over the frequencies of 7MHz to 12MHz, we can use the formula for thermal noise power,
P = k * T * B
where P is the power, k is Boltzmann's constant (1.3806 × 10^-23 J/K), T is the temperature in Kelvin (300K), and B is the bandwidth (12MHz - 7MHz = 5MHz = 5 × 10^6 Hz).
Substituting the values into the formula,
P = (1.3806 × 10^-23 J/K) * (300K) * (5 × 10^6 Hz)
P ≈ 2.071 × 10^-11 J
To convert the power to dBm, we can use the formula,
P(dBm) = 10 * log10(P/1mW)
Substituting the power in milliwatts (1mW = 10^-3 W) into the formula,
P(dBm) = 10 * log10((2.071 × 10^-11 J)/(10^-3 W))
P(dBm) ≈ -101.99 dBm
Therefore, the power produced by a 500kΩ resistor at a temperature of 300K over the frequencies of 7MHz to 12MHz is approximately -101.99 dBm.
Learn more about frequencies from the given link:
https://brainly.com/question/27151918
#SPJ11
What is the difference between the terms voltage, EMF, and
potential difference ? Thanks!
Voltage, EMF and potential difference are terms that are frequently used in relation to electricity. Although these terms are similar in definition, they differ in the specific way that they describe an electrical system.
The term voltage is defined as the difference in electric potential energy per unit charge between two points in a circuit. Voltage is often referred to as an electrical pressure. It is the potential difference that drives the current through an electrical circuit.
EMF stands for electromotive force. EMF is the voltage generated by a source, like a battery or generator. The term "electromotive force" is a misnomer since it is not a force at all. Instead, it is a potential difference that arises from the flow of charge through a circuit.
The potential difference is the difference in electric potential between two points in an electric circuit. It is also known as the voltage drop. Potential difference is measured in volts. It is the difference in the electric potential energy of a charge that has moved between two points in a circuit.
To learn more about potential visit;
https://brainly.com/question/28300184
#SPJ11
Atmospheric pressure at sea levei is 1.013×105 Pa. The density of seawater is 1.03×103 kg/m3. Men, who is vacationing in the Caribbean, spends a day snorkeling to see the underwater sea life. At what depth in the sea water does Ken experience a sauge pressure equal to 1 atmosphere? 7.5 m 15m 0m 98m 10 m
Ken will experience a pressure equal to 1 atmosphere at a depth of 10 meters in the seawater.
The main answer is 10 meters because the pressure in a fluid, such as seawater, increases with depth due to the weight of the overlying fluid. This pressure increase is known as hydrostatic pressure. The relationship between depth and pressure is described by Pascal's law, which states that pressure is directly proportional to the depth and density of the fluid.
Atmospheric pressure at sea level is approximately 1 atmosphere, which is equivalent to 1.013×10^5 pascals (Pa). To calculate the depth at which Ken will experience a pressure equal to 1 atmosphere, we need to consider the hydrostatic pressure equation:
P = ρgh,
where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth.
Given the density of seawater as [tex]1.03×10^3 kg/m^3[/tex], we can rearrange the equation to solve for h:
h = P / (ρg) = [tex](1.013×10^5 Pa) / (1.03×10^3 kg/m^3 × 9.8 m/s^2)[/tex] ≈ 10 meters.
Therefore, at a depth of 10 meters in the seawater, Ken will experience a pressure equal to 1 atmosphere.
Learn more about hydrostatic pressure
brainly.com/question/14810152
#SPJ11
1. Consider the function Y(x, t) = x² + bxt + t², where b is some constant. a. The general solution to the wave equation has the form Y(x, t) = f(x - vt) + g(x + vt). By inspection, write down two values of b that would make the given function a wave, and in each case give the corresponding velocity. c. b. Show, by direct substitution of the function into the wave equation itself, that in fact b can be any value and still the function represents a wave. Comment on the wave's velocity. Suppose b = 0 so that y(x, t) = x² + t². By trial and error find a way to express this in the form Y(x, t) = f(x - vt) + g(x + vt). The value to use for tv should be clear from the previous part.
The wave travels in both directions at the same speed as the distance from the origin.
The given function can be written in the form of a wave equation:
Y(x, t) = f(x - vt) + g(x + vt)For the given function to be a wave, the values of b must be such that f(x-vt) and g(x+vt) correspond to waveforms.
Two values of b that would make the given function a wave are:
b = 1, and b = -1.
In the case of b = 1, v = 2x
In the case of b = -1, v = -2x
Comment on the wave's velocity:
The wave's velocity is determined by the value of b. The wave's velocity is negative when b is negative, and positive when b is positive. If b is equal to zero, the wave's velocity is zero. b. We must substitute Y(x, t) = x² + bxt + t² into the wave equation to demonstrate that it is a wave.
The wave equation is:
∂²Y/∂x² = (1/v²) ∂²Y/∂t²
∂²Y/∂x² = 2b + 2x²
∂²Y/∂t² = 2
substituting these in the wave equation gives:
(2b + 2x²)/v² = 2, which can be simplified to v² = b + x².If b is negative, the wave travels to the left with a velocity equal to the square root of b+x². If b is positive, the wave travels to the right with a velocity equal to the square root of b+x². c. We must convert the given function
Y(x, t) = x² + t²
Y(x, t) = f(x-vt) + g(x+vt)
b = 0. Let f(x-vt) = x² - vt
g(x+vt) = vt + x².
Substituting these into the wave equation (as in the previous part) will demonstrate that this waveform is also a wave. We have
f(x-vt) = g(x+vt) = x² + t²/2.
Y(x, t) = f(x-vt) + g(x+vt) = 2x² + t
v² = x², implying that v = ±x. The values are clear from the previous part, as b = 0.
To know more about wave travels please refer to:
https://brainly.com/question/13771235
#SPJ11
1. Explain the following, give 2 sample problem with solution and draw phasor diagrams and current and voltage waveforms:
(a) purely resistive,
(b) purely inductive
(c) purely capacitive a.c. circuits
2. Explain the following ,give 2 sample problem with solution draw circuit diagrams, phasor diagrams and voltage and impedance triangles
(a) R–L series a.c. circuits
(b) R–C series a.c. circuits
(c) R–L–C series a.c. circuits
1. a. Purely resistive A.C. circuits: A circuit that contains only resistance and an alternating source is called a purely resistive AC circuit. In a purely resistive AC circuit, the current and voltage are in phase. The circuit is similar to that of a DC circuit.
Problem 1Solution:The following circuit is a pure resistive circuit with resistance R connected to a sinusoidal voltage source of amplitude V₀ and frequency ω. We can use Ohm's Law and the voltage-current relationship to derive expressions for the voltage and current in the circuit. I = V₀/R is the RMS value of the current in the circuit. Phase angle Φ = tan⁻¹ (0) = 0°Impedance of the circuit = R Phasor diagram of the circuit:
Voltage and current waveforms of the circuit:
Problem 2Solution:The following circuit is a pure resistive circuit with resistance R₁ and R₂ connected in series with a sinusoidal voltage source of amplitude V₀ and frequency ω. We can use Ohm's Law and the voltage-current relationship to derive expressions for the voltage and current in the circuit. I = V₀ / (R₁ + R₂) is the RMS value of the current in the circuit. Phase angle Φ = tan⁻¹ (0) = 0°
2. a. R–L series AC. circuits An R-L series circuit consists of a resistor and an inductor connected in series with an AC source. When the circuit is connected to the AC source, an alternating current flows through it. The current lags behind the voltage by a certain angle due to the presence of the inductor. The inductive reactance opposes the flow of current in the circuit.
Problem 1Solution:In an R-L series circuit, the voltage across the resistor is in phase with the current, while the voltage across the inductor lags behind the current by 90°.
Problem 2Solution:In an R-L series circuit, the voltage across the resistor is in phase with the current, while the voltage across the inductor lags behind the current by 90°.
2. b. R–C series AC circuits: An R-C series circuit is made up of a resistor and a capacitor connected in series with an AC source. The voltage across the resistor and the capacitor is in phase with the current. The capacitive reactance opposes the flow of current in the circuit.
Problem 1Solution:In an R-C series circuit, the voltage across the resistor and the capacitor is in phase with the current.
Problem 2Solution:In an R-C series circuit, the voltage across the resistor and the capacitor is in phase with the current.
2. c. R–L–C series AC circuits: An R-L-C series circuit is made up of a resistor, an inductor, and a capacitor that are all connected in series with an AC source. The current in the circuit is the same as the current in each element, but the voltage across each element differs depending on its reactance. Depending on the relative values of R, L, and C, the current can lead or lag behind the voltage. The circuit's impedance is determined by the values of R, L, and C.
Problem 1Solution:In an R-L-C series circuit, the current leads the voltage in a certain range of frequencies, while in other frequency ranges, the current lags behind the voltage. The impedance of the circuit varies with frequency.
Problem 2Solution:In an R-L-C series circuit, the current leads the voltage in a certain range of frequencies, while in other frequency ranges, the current lags behind the voltage. The impedance of the circuit varies with frequency.
To know more about Purely resistive, refer
https://brainly.com/question/29109303
#SPJ11
Imagine that a star is surrounded by a debris disk that lies a distance D from it. The disk contains n spherical grains, each of radius r. Derive an equation for the fraction f of the light from the star intercepted by the dust grains. Write the equation you derive here. Explicitly indicate multiplication with a * symbol.
To derive an equation for the fraction f of the light from the star intercepted by the dust grains in the debris disk, we can use the concept of cross-sectional area.
Let's assume that the total cross-sectional area of all the dust grains combined is A. The cross-sectional area of each individual dust grain can be approximated as the area of a circle, which is given by:
A_grain = π * r².
The total area covered by the dust grains can be expressed as the product of the number of grains and the area of each grain, which is ;
A_total = n * A_grain.
Now, the total area covered by the dust grains is intercepting a fraction f of the total area from the star's light. Therefore, we have the equation:
A_total / A = f
Substituting the values of A_total and A, we get:
n * A_grain / A = f
Since the area of each grain is A_grain = π * r², we can rewrite the equation as:
n * (π * r²) / A = f
This is the derived equation for the fraction f of the light from the star intercepted by the dust grains.
To learn more about derived equation for Area of cross section:
https://brainly.com/question/13719022
#SPJ11
Compute the quantity of charge stored in 150 uF Capacitor if it is connected to 200V source. Calculate the capacitance of a capacitor of 50 reactance, when it is supplied by source of 20 kHz frequency.
The capacitance of a capacitor with 50 reactance when given a source of 20 kHz frequency is 15.92 nF.
Compute quantity of charge stored in 150 uF Capacitor if it is connected to 200V source:To compute the amount of charge stored in a capacitor, we may utilize the formula below.Q = CV Where:Q is the amount of charge stored.C is the capacitance V is the voltage
If we plug in the provided values we get,Q = CV = 150 × 10⁻⁶ × 200VQ = 30 μC.So, the amount of charge stored in a 150 μF capacitor linked to a 200V source is 30 μC. Calculate the capacitance of a capacitor of 50 reactance when it is supplied by a source of 20 kHz frequency
For this situation, we can utilize the following formula,Xc = 1 / (2πfC)Where:Xc is the capacitive reactancef is the frequency C is the capacitance. To obtain the capacitance, we rearrange the equation and get,C = 1 / (2πfXc)We can now plug in the supplied values and obtain,C = 1 / (2π × 20 × 10³ × 50)C ≈ 15.92 nF
Thus, the capacitance of a capacitor with 50 reactance when given a source of 20 kHz frequency is 15.92 nF.
In conclusion, Capacitors are electrical elements that may store electrical charge. In an electrical circuit, they are frequently utilized to block DC while allowing AC to pass through. Capacitance is the capacitance of a capacitor, and it is measured in farads (F). They are frequently utilized in electronic devices, including amplifiers, power supplies, and speakers, among others.
Know more about capacitance here:
https://brainly.com/question/31871398
#SPJ11
The angular position of a point on a rotating wheel is given by theta = 7.85t * 2.85t ^ 2 + 1.77t ^ 3 where is in radians and t is in seconds. At t = 0, what are (a) the point's angular position and (b) its angular velocity? (c) What is its angular velocity at t = 6.29s ? (d) Calculate its angular acceleration at t=2.13 s.(e) its angular acceleration constant?
Therefore, the point's angular acceleration when t = 2.13s is 99.589 rad/s2.(e) Angular acceleration constantSince the angular acceleration is not constant, the question of angular acceleration constant does not apply.
Given equation: $$\theta = 7.85t * 2.85t^2 + 1.77t^3$$where $\theta$ is in radians and t is in seconds.(a) The point's angular position when t = 0.Substitute t = 0 in the above equation,$$\theta = 7.85(0) * 2.85(0)^2 + 1.77(0)^3$$$\theta = 0$ radians(b) The point's angular velocityTo find the angular velocity, differentiate the equation with respect to time.$$ \begin{aligned} \frac{d\theta}{dt} &= \frac{d}{dt}(7.85t * 2.85t^2 + 1.77t^3) \\ &= 7.85 * 2.85t^2 + 7.08t^2 \\ &= 7.08t^2(1 + 2.85) \\ &= 23.352t^2 \end{aligned} $$Substitute t = 0 to find the point's angular velocity at t = 0.$$ \begin{aligned} \frac{d\theta}{dt} &= 23.352t^2 \\ &= 23.352(0)^2 \\ &= 0 \end{aligned} $$Therefore, the point's angular velocity when t = 0 is zero.(c) The point's angular velocity when t = 6.29sSubstitute t = 6.29 in the equation for angular velocity.$$ \begin{aligned} \frac{d\theta}{dt} &= 23.352t^2 \\ &= 23.352(6.29)^2 \\ &= 926.089 \ rad/s \end{aligned} $$Therefore, the point's angular velocity at t = 6.29s is 926.089 rad/s.(d) The point's angular acceleration when t = 2.13sTo find the angular acceleration, differentiate the angular velocity with respect to time.$$ \begin{aligned} \frac{d^2\theta}{dt^2} &= \frac{d}{dt}(23.352t^2) \\ &= 46.704t \\ &= 46.704(2.13) \\ &= 99.589 \ rad/s^2 \end{aligned} $$
#SPJ11
