Consider a wave that is traveling in the positive z direction, which is incident on a junction with another transmission line. The wave is on transmission line 1 in the region z 0, with characteristic impedance Zo1, and to the right of the junction (z> 0) is transmission line 2 with characteristic impedance Zo2. Assume for simplicity that the incident voltage wave has a voltage of 1.0 [V]. Solve for the reflected and transmitted voltages and currents on both sides of the junction. From this, show that the total current is continuous at the junction. Also show that the total power flowing in the z direction is the same on either side of the junction. Recall that the voltage transmission coefficient is related to the voltage reflection coefficient by Note that the total voltage and current on the left line (ine1) are found from summing the voltage and current for the incident and reflected waves, while the total voltage and current on the right line (line 2) are those of the transmitted wave. Also, note that power is given by P-VI, where Vand I are the total voltage and current in the time domain.

Answers

Answer 1

The correct answer is According to P = V I and P = V/I, the source's power (P) input to the circuit is determined.

P = E/t is the equation, where P stands for power, E for energy, and t for time in seconds. According to this equation, power is defined as the amount of energy consumed per unit of time. Ohm's Law states that the electrical current in a circuit may be estimated by dividing the voltage by the resistance in the first iteration of the calculation, I = V/R. In other words, the voltage and resistance are inversely related to the current and directly proportional to each other. Ohm's Law describes the connection between current, voltage, and resistance. This asserts that, given the temperature is constant, the current flowing in a circuit is directly proportional to the applied voltage and inversely proportional to the circuit resistance.

To learn more about circuit click the link below:

brainly.com/question/27206933

#SPJ4


Related Questions

An air outlet that supplies conditioned air is called a
A. ventilator.
B. diffuser.
C. louver.
D. return grille.

Answers

A diffuser is a type of air outlet that releases conditioned air.

What is meant by diffuser?A compressor or pump's diffuser is an essential component. Its goal is to raise pressure by slowing the flow as it leaves the impeller. The diffuser can be easily represented as a nonrotating channel with increasing flow area in the flow direction. Here is a brief explanation of what a diffuser does: A diffuser, which is typically an ultrasonic device driven by electricity and hooked into a wall socket, creates a fine, cold mist out of clean water and only the purest essential oils, which is then released into the air for us to breathe and feel through aroma. A diffuser is an apparatus that lowers a fluid's pressure by slowing it down. When a flow is subsonic or supersonic, the cross sectional area of a nozzle increases in the flow direction.

To learn more about diffuser, refer to:

https://brainly.com/question/13752102

#SPJ1

Gae from the combution chamber were o hot that pipe around the nozzle carried coolant to keep the nozzle from melting. True or fale

Answers

TRUE . In outer space, the shuttle could generate more than half a million pounds of thrust.Pipes around the nozzle carried coolant that kept the nozzle from melting.

What exhaust system modifies the thrust direction to modify the direction of a rocket?

The rocket's exhaust nozzle can rotate from to side in a gimbaled propulsion system.The thrust's direction changes in relation to the rocket's center of gravity when the nozzle is moved.

How can rocket motors avoid melting?

The most popular method for preventing a liquid-fueled rocket engine form melting is regenerative cooling.In this procedure, the propellant passes partially or completely through the nozzle and combustion chamber walls before passing through the injector and entering the chamber.

To know more about combution visit:

https://brainly.com/question/30008016

#SPJ4

a heat engine with a thermal efficiency of 50% produces 200 kj of net work output. determine the heat input. multiple choice question. 200 kj 400 kj 50 kj 100 kj

Answers

If a heat engine with a thermal efficiency of 50% produces 200 kj of net work output, the heat input is 400 kJ.

The thermal  efficiency of a heat engine is defined as the amount of usable work that is produced for a given amount of heat energy input.

Thermal efficiency is defined as a percentage of the quantity of heat delivered to the amount of heat obtained from the heat engine. If we offer 100% heat energy, it will be lowered to its lowest level once the procedure is completed. So, at any  time, we will notice a difference between those two values, and that difference is nothing more than the thermal efficiency, which may be either 1% or 100%.

Mathematically,

efficiency = (output work/input energy) x 100%

Information available in the problem:

efficiency = 50%

output work = 200 kJ

Hence,

heat input = output work/efficiency

                 = 200 kJ/50%

                 = 200/0.5 = 400 kJ

Learn more about heat engine here:

https://brainly.com/question/13087750

#SPJ4

JS
Create a function findWaldo that accepts an object and returns the value associated with the key 'Waldo'. If the key 'Waldo' is not found, the function should return 'Where's Waldo?'
// ADD CODE HERE
// Uncomment these to check your work!
// const DC = {'Bruce': 'Wayne', 'Harley': 'Quinn'}
// const supernatural = {'Sam': 'Winchester', 'Dean': 'Winchester', 'Waldo': 'unknown'}
// console.log(findWaldo(DC)) // should log: 'Where's Waldo?'
// console.log(findWaldo(supernatural)) // should log: 'unknown'

Answers

Anywhere in your application, you can invoke a function, which is a collection of reusable code. This avoids the need to repeatedly write the same code.

What is the role of JavaScript?

A function in JavaScript is similar to a procedure in that it is a group of statements that perform an action or compute a value. However, a process must accept an input and create an output with a clear connection between the input and the outcome in order to be termed a function.

How many types are supported by JS?

JavaScript generally supports four different kinds of functions: Regular function: executes after calling and always completes; can return anything. The generator function can be initiated and canceled using the yield operator.

To know more about JS Functions visit:

https://brainly.com/question/12978370

#SPJ4

a body is kept moving in a circle of constant radius. if the speed of the body ius doubled, the centripetal acceleration will. the horizontal distance travelled by a projwectile is called the. the rising and falling times of a projectile are equal if the launching position is the landing position

Answers

The horizontal distance travelled by a projectile is called its range.

What is the acceleration?The rate at which velocity changes is called acceleration. Acceleration often indicates a change in speed, but not necessarily. An item that follows a circular course while maintaining a constant speed is still moving forward because the direction of its motion is shifting.acceleration: the rate at which the speed and direction of a moving object vary over time. A point or object going straight forward is accelerated when it accelerates or decelerates.zero,Acceleration is 0 in a circular motion that is uniform.The formula for centripetal acceleration is a=v 2 /R. Therefore, if v is doubled and R is cut in half, we have a ′ = 4v 2 /(R/2)=8a.

To learn more about acceleration refer to:

https://brainly.com/question/460763

#SPJ4

Using the method of joints, determine the force in each
member of the truss shown. State whether each member is in tension
(T) or compression (C).

Answers

Each member is in tension (T) or compression (C) is F_AB = F_AD = F_BC =  F_CD.

What is compression?
Compression is the process of reducing the size of a file or data by encoding it using fewer bits. It helps to reduce the amount of space needed to store and transfer data. Compression techniques can be used to reduce the size of digital images, audio, video, and other types of data.

Given:

The truss shown consists of four members: AB, BC, CD, and AD.

Using the method of joints, we can determine the forces in each member by considering the equilibrium of each joint.

For joint A:

Sum of forces in the x-direction = 0

F_AB - F_AD = 0

F_AB = F_AD

For joint B:

Sum of forces in the x-direction = 0

F_AB - F_BC = 0

F_AB = F_BC

For joint C:

Sum of forces in the x-direction = 0

F_BC - F_CD = 0

F_BC = F_CD

For joint D:

Sum of forces in the x-direction = 0

F_AD - F_CD = 0

F_AD = F_CD

Therefore, we can conclude that the forces in each member are equal.

F_AB = F_AD = F_BC = F_CD

To learn more about compression
https://brainly.com/question/12976653

#SPJ4

vacuum leak testing is being discussed. technician a says to use a vacuum pump to check each component. technician b says to use an ultrasonic tester. who is correct?

Answers

The correct answer is  technician a  says to use a vacuum pump to check each component.

Vacuum pumps, in the simplest terms, are mechanical devices that make it possible to remove gas and air molecules from a sealed space to produce a space free of gas and/or air. Their main functions are to clean and seal. Depending on the medium being pushed through them, vacuum pumps are available in wet or dry versions. Follow these steps to test the pump: Close the valve between the system and the vacuum pump/micron gauge setup and start the vacuum pump before opening the vacuum pump and micron gauge to the system. Only the vacuum hose and micron gauge will be vacuumed as a result of this.

To learn more about vacuum click the link below:

brainly.com/question/29242274

#SPJ4

In this lab, you'll practice creating classes and objects, using ArrayList objects, and working
with interacting objects (with some nice visuals). Even better, you'll be working with circles,
widely considered to be the roundest of all two-dimensional shapes.
1. Import the starter code to begin. Instructions (if needed), for your IDE of choice:
a. Jgrasp:
i. Download the starter code folder from the website (Download -> Direct download).
ii. Extract (unzip) the downloaded folder (right-click -> Extract all).
iii. Copy the entire (unzipped) folder to your H: drive; rename it in the usual fashion.
b. Eclipse:
i. In Eclipse, create a new Java project named in the usual fashion.
ii. Download the starter code folder from the website (Download -> Direct download).
iii. Extract (unzip) the downloaded folder (right-click -> Extract all).
iv. Drag and drop the unzipped materials as follows:
1. Drag the source (*.java) files into the "src" folder.
2. See here for help (don't worry about text files): youtu.be/LOSICIeP6Ko
2. Create a class Circle.java which is a simple abstraction of an on-screen circle (image). A Circle
should (initially) have the following:
int x and int y The center point of the circle's on-screen location. These values represent
the circle's (initial) location on screen.
int radius The radius of the circle.
Color color The color of the circle. Color is a class that is built into Java, a software
abstraction of color. You can create a new color using Color's
three-parameter constructor (e.g. new Color(50, 100, 150)), where
each integer is a value 0-255 (corresponding to red, green, and blue
components, respectively). There are also pre-built colors in the Color class
that you can use, e.g. Color.RED or Color.BLACK. Import:
java.awt.Color.
3. Write Circle's 4-parameter constructor. Give the parameter variables real good names.
4. A Circle is responsible for drawing itself. Write a void draw() method that displays the circle on
screen using the StdDraw.java graphics library (included in starter code). Use the following:
StdDraw.setPenColor(color); //set the current color of the drawing window
StdDraw.filledCircle(x, y, radius); //draw a filled circle at , diam of radius*2
Page 1 of 5
5. The CircleAnimations class performs some on-screen animations using Circle objects; we say
CircleAnimations is a client of the Circle class.
a. CircleAnimations' constructor has been written for you. Nice! Look it over so you know what
variables a CircleAnimations object will have. For example, this class maintains a list of all the
circles currently in the animation.
6. In CircleAnimations, write a method void drawCircles() that will iterate through all objects in
the circles list and draw them to the screen. The drawCircles method should be called last
from any method that adds circles to the list or makes changes to the circles so that the results
appear on screen. You don't need to test this method quite yet.
7. In CircleAnimations, write a method void addCircles() that will add three randomly colored
circles with random locations to the circles list. Note: The size of the drawing window is saved
into CircleAnimations' size instance variable. Choose a random radius range you feel best
represents you as a person.

Answers

In this workshop you will practice creating classes and objects, using Array.

List objects and working with interactive objects (with nice visual effects). You'll also work with circles, widely considered to be the roundest of all two-dimensional shapes. First, import your startup code. Instructions (if required) for the selected IDE: a. Jack: Me. Download the boot code folder from the website (Download -> Direct Download).ii. Extract (extract) the downloaded folder (right click -> extract all).iii. Copy the entire folder (unzipped) to drive H:; Rename it as usual. Eclipse: i. In Eclipse, create a new Java project with the usual name. ii. Download the initial code folder from the website (Download -> Direct Download).iii. Extract (extract) the downloaded folder (Right Click ->Extract All).iv. Drag the extracted materials as follows Drag & Drop: 1. Put the source files (*.java) in the "src" folder. Here's some help (don't worry about text files): youtu.be/LOSICIeP6Ko 2. Create a Circle.java class that is a simple abstraction of a circle (image) on the screen. The circle should (initially) have the following values: int x and int y The center of the circle's position on the screen. These values ​​represent the starting position of the circle on the screen. In this workshop you will practice creating classes and objects, using Array List objects and working with interactive objects (with nice visual effects). You'll also work with circles, widely considered to be the roundest of all two-dimensional shapes. First, import your startup code. Instructions (if required) for the selected IDE: a. Jack: Me. Download the boot code folder from the website (Download -> Direct Download).ii. Extract (extract) the downloaded folder (right click -> extract all).iii. Copy the entire folder (unzipped) to drive H:; Rename it as usual. Eclipse: i. In Eclipse, create a new Java project with the usual name. ii. Download the initial code folder from the website (Download -> Direct Download).iii. Extract (extract) the downloaded folder (Right Click ->Extract All).iv. Drag the extracted materials as follows Drag & Drop: 1. Put the source files (*.java) in the "src" folder. Here's some help (don't worry about text files): youtu.be/LOSICIeP6Ko 2. Create a Circle.java class, which is a simple abstraction of a circle (image) on the screen.

The circle should (initially) have the following values: int x and int y The center of the circle's position on the screen. These values ​​represent the starting position of the circle on the screen.

To know more about objects visit:

brainly.com/question/14964361

#SPJ4

Determine the location { x }_{ c }x c of the centroid of the solid made from a hemisphere, cylinder, and cone.
Given:
a = 8080 mmmm
b = 6060 mmmmc = 3030 mmmm
d = 3030 mmmm

Answers

The correct answer is a = 8080 mmmm  the location { x }_{ c }x c of the centroid of the solid made from a hemisphere, cylinder, and cone.

A hemisphere's curved surface area is equal to 2r2 square units. A hemisphere's entire surface area is 3 r 2 square units. The formula (23)r3 cubic units is used to calculate the volume of a hemisphere. As shown in the image, a right circular cylinder with length ′a′ and radius ′r′ has its origin as its centre and its axis along the x-axis such that one face is at x=+a/2 and the other is at x=a/2. When an electric field is operating parallel to the x-axis, E =E0i for values greater than zero and E =E0i for values lower than zero.

To learn more about hemisphere click the link below:

brainly.com/question/13625065

#SPJ4

1.4-1 a hollow circular post abc (see figure) supports a load p1 51700 lb acting at the top. a second load p2 is uniformly distributed around the cap plate at b. the diameters and thicknesses of the upper and lower parts of the post are dab 51.25 in., tab 5 0.5 in., dbc 5 2.25 in., and tbc 5 0.375 in., respectively. (a) calculate the normal stress s ab in the upper part of the post. (b) if you want the lower part of the post to have the same compressive stress as the upper part, what should be the required magnitude of load p2?

Answers

A. The normal stress s ab in the upper part of the post is 1443 psi.

B. The required magnitude of load p2 is 1488 lbs.

What is stress?

The force acting across a material's entire surface area is referred to as stress. Strain is the result of stress on the body. Deforming forces are those that alter the structure of an object. An object is deforested when we apply a deforming force to it. There will be an opposing force created inside the object called the restoring force that will work to restore the object to its original size and shape.

Newton's third law states that the restoring force will be equal in magnitude and directed in the opposite direction from the applied deforming force if there is no permanent change in the body's configuration. Therefore, stress is a measurement of the restoring force produced per unit area of the material.

Part A:

[tex]$$\begin{aligned}& \mathrm{P}_1=1700 \quad \mathrm{~d}_{\mathrm{AB}}=1.25 \quad \mathrm{t}_{\mathrm{AB}}=0.5 \\& \mathrm{~d}_{\mathrm{BC}}=2.25 \quad \mathrm{t}_{\mathrm{BC}}=0.375 \\& \mathrm{~A}_{\mathrm{AB}}=\frac{\pi\left[\mathrm{d}_{\mathrm{AB}}{ }^2-\left(\mathrm{d}_{\mathrm{AB}}-2 \mathrm{t}_{\mathrm{AB}}\right)^2\right]}{4} \\\\\end{aligned}$$[/tex]

[tex]\begin{aligned}\\& \mathrm{~A}_{\mathrm{AB}}=1.178 \quad \sigma_{\mathrm{AB}}=\frac{\mathrm{P}_1}{\mathrm{~A}_{\mathrm{AB}}} \\& \sigma_{\mathrm{AB}}=1443 \mathrm{psi} \quad \leftarrow\end{aligned}$$[/tex]

the normal stress s ab in the upper part of the post is 1443 psi.

Part B

[tex]\begin{aligned}\\& \mathrm{A}_{\mathrm{BC}}=\frac{\pi\left[\mathrm{d}_{\mathrm{BC}}^2-\left(\mathrm{d}_{\mathrm{BC}}-2 \mathrm{t}_{\mathrm{BC}}\right)^2\right]}{4} \\& \mathrm{~A}_{\mathrm{BC}}=2.209 \quad \begin{array}{c}\mathrm{P}_2=\sigma_{\mathrm{AB}} \mathrm{A}_{\mathrm{BC}}-\mathrm{P}_1 \\\mathrm{P}_2=1488 \mathrm{lbs} \quad \leftarrow \quad \end{array}\\\end{aligned}[/tex]

The required magnitude of load p2 is 1488 lbs.

Learn more about stress

https://brainly.com/question/12871096

#SPJ4

The rigid bar EFG is supported by the truss system shown. Determine the cross-sectional area of member AE for which the normal stress in the member is 15 ksi. It is given that p=4200 lb. 6 bula P 4f74f- 4f- The cross-sectional area of member AE is i n?

Answers

The physiological cross-sectional area (PCSA) of a muscle, typically at its biggest point, is the area of the cross section of a System taken perpendicular to its fibers.

It is frequently employed to explain how pennate muscles contract. In contrast, the cross-sectional area is the area obtained when splitting the identical item into two. Cross sectional area refers to the size of that specific cross section. When an object is present at a location, its area is measured; however, when a 3D object is cut perpendicularly, its cross-sectional area is measured. Any rectangular solid, including a cube, has a volume equal to the base's area (length times width) times the height: V = l × w × h.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

Personal protective equipment (PPE) protects fire fighters in hazardous atmospheres. Which of the following is designed to protect fire fighters during most building fires?

Answers

US The turnout outfit, which consists of a protective coat and pants, is a requirement for firefighters, as well as other personal protective equipment (PPE) such a helmet, gloves, boots, and a self-contained breathing apparatus.

They should correctly wear an SCBA until it is considered safe to remove it in order to prevent exposures to hazardous chemicals through inhalation and skin absorption. Following an emergency reaction, a process known as secondary decontamination, firefighters are still at risk of inhaling dangerous substances. Protective clothing with a support function (meets NFPA 1993) air-purifying, canister-equipped, full-facepiece respirator. Safety boots and gloves that can withstand chemicals. Self-contained breathing apparatuses (SCBA) are essential for firefighters because they shield them from hazardous heat and poisonous smoke. The safety of the nation's firefighters quickly improved as a result of NIST research that contributed to strengthening industry standards for SCBA performance.

Learn more about gloves  at:

https://brainly.com/question/1618277

#SPJ4

The X. 500 standard defines a protocol for a client application to access an X. 500 directory known as which of the following options?
a. DIB
b. DAP
c. DIT
d. LDAP

Answers

Answer:

Option B is the correct answer for the above question.

Explanation:

DAP is a protocol technology that is used for the client and discovered by X.500 in 1988. Its use for the client host on the network. The operation of this protocol is --- Read, Bind, Search, List, Compare, Add and Modify the data.

The above question asked about the protocol which is searched by X.500 and used for the clients. So the answer is DAP which is stated by Option B hence this option is correct while other is not because--

   Option 'A' states about DIB which is not a protocol. It is used by X.500.

   Option C states about DIT which is not used by X.500.

   Option D states about LDAP which can be used for client or server.

To know more about protocol  visit:

https://brainly.com/question/27581708

#SPJ4

The X. 500 standard defines a protocol for a client application to access an X. 500 directory known as DAP .

Option B is correct.

DAP is a client-oriented protocol technology that was discovered in 1988 by X.500. Its application to the network's client host. This protocol reads, binds, searches, lists, compares, adds, and modifies data.

The protocol that X.500 looks up and uses for clients was the subject of the aforementioned question. Therefore, Option B's answer, DAP, is correct, whereas Option 'A' is not because Option 'A' refers to DIB, which is not a protocol. X.500 makes use of this.

 Option C mentions DIT, which X.500 does not employ.

  Option D describes LDAP as a client or server protocol.

To know more about protocol :

brainly.com/question/27581708

#SPJ4

tech a says that during a brake inspection, it is good practice to carefully peel back the dust boot from a wheel cylinder and see if there is any brake fluid behind the dust boot. a little brake fluid is normal. tech b says that during a brake inspection, it is good practice to carefully peel back the dust boot from a wheel cylinder and see if there is any brake fluid behind the dust boot. if there is, the wheel cylinder is starting to leak and should be replaced. who is correct

Answers

According to the question of wheel cylinder, tech b is correct that says during a brake inspection.

What is wheel cylinder?
A wheel cylinder is a component of a drum brake system in a vehicle. It is a cylinder that contains two pistons, one at each end, which press against the brake shoes when the brakes are applied. The pistons are connected to the brake pedal by a hydraulic system, and when the pedal is pressed down, hydraulic pressure is sent to the wheel cylinder, forcing the pistons outward and against the brake shoes. This action causes the brake shoes to press against the drum, slowing the vehicle down. Wheel cylinders are important in the proper functioning of a drum brake system, as they are responsible for the mechanical action of the braking process. They must be maintained regularly to ensure that they are functioning correctly and do not leak, as this can cause the brakes to fail.

To learn more about wheel cylinder
https://brainly.com/question/28542295

#SPJ4

A drawing requires a welder to make a 1/4"" fillet weld 16"" long. What is the volume of weld metal required to make this weld?

Answers

Making sure that the length of the weld is also given in centimetres, multiply the length of the weld by the area to determine the volume.

How much welding metal is needed to make this weld?

Making sure that the length is also given in centimetres, multiply the weld's length by its area to determine the volume. In this example, the volume is 507 cubic centimetres per metre (cu. cm/m), which is how volume is typically expressed.

Add the weld strength and size together. Subtract the above product from the maximum permitted tensile stress. To determine how long the weld joint is, multiply the result by 0.707.

By multiplying the parcel's length, width, and height (all expressed in centimetres) and dividing the result by 5000, volumetric weight is most frequently calculated (some carriers use a divisor of 4000).

To learn more about volume refers to:

https://brainly.com/question/24086520

#SPJ4

The oxygen binding curve of which of the following is the closest to that of myoglobin? a.hemoglobin at pH 6.8 b.hemoglobin that lacks BPG c. maternal hemoglobin d.fetal hemoglobin

Answers

The oxygen binding curve of hemoglobin devoid of BPG is comparable to that of myoglobin.

Option B is correct.

What is 2,3-BPG ?

As an intermediate in the glycolysis process, 2,3-BPG is a naturally occurring molecule. It is a hemoglobin allosteric effector. Oxygen binding curve without 2,3-BPG In the absence of 2,3-BPG, this molecule will unbind in the center of the structure of hemoglobin. This will keep hemoglobin in its relaxed state and prevent it from rapidly changing into its tensed state.

That is, after unbinding with hemoglobin, 2,3-BPG raises hemoglobin's affinity for oxygen, causing the oxygen-binding curve to shift all the way to the left, just like myoglobin's. The T-state of deoxyhemoglobin causes the equilibrium to shift to the R-state, where the majority of hemoglobin will be bound to oxygen (i.e., have a high affinity for oxygen) and the deoxyhemoglobin will not exist for long.

Learn more about Myoglobin :

brainly.com/question/9433464

#SPJ4

An ultrasonic occupancy sensor emits high-power, low-frequency sound waves and
listens for a phase shift in the reflected sound returning to the sensor, which
indicates a moving target.
True
False

Answers

The correct answer is False. An ultrasonic occupancy sensor emits high-power, low-frequency sound waves andlistens for a phase shift in the reflected sound returning to the sensor, whichindicates a moving target.

Simply said, ultrasound is sound that is audible to humans yet has a frequency higher than 20 kHz.Ultrasound is employed at frequencies up to several GHz at the high end of the spectrum. Ultrasonic equipment is used for both object detection and distance measures. In medicine, sonography and ultrasound imaging are often employed. Ultrasound is used to find hidden faults in goods and buildings during nondestructive testing.Ultrasonic sensors operate by discharging sound waves at a frequency that is inaudible to humans.

To learn more about ultrasonic click the link below:

brainly.com/question/21336084

#SPJ4

Two concurrent application, a1 and a2, execute the equence of intruction (j1, j2, j3) and (k1, k2, k3), repectively. Execution witche between the application whenever a timeout interrupt occur or when one application terminate. If a2 tart, and interrupt occur after intruction k2 and j1, then what i the order in which the 6 intruction will execute?

Answers

Two concurrent applications a1 with a sequence of instructions  (j1, j2, j3)  and a2 with a sequence  of instructions  (k1, k2, k3). The order in which the 6 instructions will be executed is: k1, k2, j1, k3, j2, j3

A concurrent application means that that application is working on more than one task at the same time. If the computer only has one CPU, the application may not operate on more than one task at the same time, yet multiple tasks are being processed at the same time inside the application. It does not complete one work before beginning the next.

In this case there are two applications with the sequence of instructions:

application a1 = (j1, j2, j3)

application a2 =  (k1, k2, k3)

The applications will be switched if one of these two conditions occurs:

- a timeout interrupt

- one application terminate

Now a2 starts. It means the instruction starts from k1, then k2.An interrupt occurs after instruction k2. It means the applications switches to a1. The instruction starts from j1.An interrupt occurs after instruction j1. Then the applications switch again to a2. The last instruction executed in a2 was k2, hence, now it executes instruction k3.After k3, it means application a2 terminates. Hence, it switches to a1 and execute j2, j3.

Therefore, the order of the executed instruction is: k1, k2, j1, k3, j2, j3

Learn more about computer instruction here:

https://brainly.com/question/14465281

#SPJ4

if the technician believes that a hermetic compressor has permanently open internal overload protector, the technician should test the compressor while it is:

Answers

The technician should test the hermetic compressor while it is still cool if they think it has an inbuilt overload safeguard that is always open. A control string is a group of two or more switch contacts that are wired together to regulate a load in a circuit or group of circuits.

The load side of the contactor is where you should check the voltage input to a compressor. Even when the exterior unit is not functioning, consumers occasionally report that it is "buzzing." The solenoid coil for the reversing valve is typically to blame for this. Most of the time, it's a low voltage gadget (24 volts), and some of them are just louder than others. This is often normal.131. When bending soft copper to any radius, it is important to keep in mind that the cross sectional area must not be drastically decreased.

To learn more about hermetic compressor click the link below:

brainly.com/question/29063130

#SPJ4

Problem 3 2 in. 2 in. 2 in. For the area shown, a. Locate the centroid. b. The moment of inertia 1, with respect to an axis through the centroid that is parallel to side AB c. The corresponding radius of gyration Rex with respect to an axis through the centroid that is parallel to side AB. 1 in. 3 in A B

Answers

Knowing the mass of the I section's centre of mass is necessary to calculate the moment of inertia of the I section.

Define centroid?

A body's geometric centre is known as a centroid. It alludes to the uniform density object's c, or centre of gravity.

A body's centroid is the location where the volume on each side is equal. A solid body made of a single material has its mass at its centroid. The centroid and centre of mass of a body are identical if its mass is dispersed evenly.

The centroid is the object's focal point. The centroid of a triangle is the location where the three medians of the triangle intersect. The intersection of all three medians is another definition for it.

To learn more about centroid refers to:

https://brainly.com/question/29868871

#SPJ4

a typical information system will have which of these? (select all that apply, omit those that do not) a) somewhere to store data (often in the form of a database) b) a user interface where commands can be issued and results received c) a program to help use the data d) software to convert knowledge into data

Answers

Computer equipment Computer software is an example of physical technology that deals with data. The software's function is to instruct the hardware on what to do in the context of telecommunications.

Human resources and procedures, databases, and data warehouses. Operational, management, and strategic level systems are the three basic kinds of information systems that cater to various organizational levels. Information systems carry out tasks like collecting input data, storing it, processing it, and finally producing output data. The components of a system are not isolated from one another; rather, they are intertwined and have an impact on one another. To accomplish the system's objective, every component is arranged in a particular way. In a bigger system, a system will have a specific role to play. System feedback exists.

To know more about Humans from the given link

https://brainly.com/question/20260001

#SPJ4

Assign jsonObject with a JSON object with properties: userName (a string), studentAge (a number) and userSiblings (an array of strings). Note: The content of the properties doesn't matter.
var jsonObject;

Answers

jsonObject = {

  userName: "John Doe",

  studentAge: 21,

  userSiblings: ["Jane", "Jack", "Jim"]

};

What is JavaScript programming language?

Interactive websites can be made using the scripting language JavaScript. It is the HTML and Web programming language.

JavaScript is used to control websites and web server software as well as to create games and make web applications more interactive.

JavaScript is an interpreted language, which means that a computer can read it and comprehend it without having to compile it into a programme. As an object-oriented language that is made for working with objects, JavaScript is also capable of producing sophisticated applications.

This question is an example of JavaScript programming.

1. Start by declaring a variable, in this case "jsonObject":

var jsonObject;

2. Assign the variable a value of a JSON object with the properties of userName (a string), studentAge (a number), and userSiblings (an array of strings):

jsonObject = {

  userName: "John Doe",

  studentAge: 21,

  userSiblings: ["Jane", "Jack", "Jim"]

};

3. The content of the properties does not matter, so you can change the values to whatever you like.

To learn more about JavaScript programming language refer :

https://brainly.com/question/13258974

#SPJ4

. The primary energy source that operates a building's air conditioning controller is typically electric,
pneumatic, or
A. thermostatic.
B. electronic.
C. hydraulic.
D. passive.

Answers

The answer should be B

a student conducts an experiment to verify whether momentum is conserved for a situation in which a collision occurs. the two objects, object x and object y, travel toward each other, as shown in figure 1. after the collision, the two objects travel as shown in figure 2. data collected from three trials of this experiment are shown in the table. which of the following statements is correct based on the data?

Answers

Momentum is a vector quantity, hence the vector sum of the momenta should be compared. After the collision, the kinetic energy of the system in scenario 1 will be lower than that in scenario 2.

The system's momentum prior to the collision and the system's momentum following the collision should be same in order to demonstrate momentum conservation. In order to determine the ultimate velocities of Cart XX and Cart YY, a student must measure the beginning velocities of Cart XX and Cart YY. The velocities of each item may be measured before to, during, and after the impact thanks to this arrangement of motion detectors and their placements. (There are two exterior sensors)

To learn more about Momentum click the link below:

brainly.com/question/24030570

#SPJ4

The service disconnecting switch for an installation consisting of a limited load on a single branch circuit shall have a rating of not less than ?

Answers

The service disconnecting method must have a rating of at least 15 amperes in installations that will only provide a single branch circuit with a restricted number of loads.

The branch circuit disconnecting method must have a rating of at least 15 amperes in installations that will only provide a single branch circuit with a small number of loads. For each service that is allowed by 230.2, a maximum of six service disconnections is authorised. Each set of service-entrance conductors allowed by 230.40, Exception No. 1, 3, 4, or 5 [230.71] are likewise subject to this rule.Any combination of the following is authorised for the two to six service disconnecting means: separate enclosures, each having a method to disconnect the main service. a primary service disconnecting mechanism included inside each panelboard enclosure.

To learn more about circuit  click the link below:

brainly.com/question/27206933

#SPJ4

a refrigerator with a cop of 3.0 accepts heat at a rate of 10 kw. determine the rate of heat rejection. multiple choice question. 40 kw 3.33 kw

Answers

The correct answer is A refrigerator's COPmax is equal to Tlow/ (Thigh - Tlow). 270/(300 - 270) = COPmax = Tlow/(Thigh - Tlow) = 9.

The usable heating or cooling delivered to work (energy) needed ratio, also known as the coefficient of performance, or COP, of a heat pump, refrigerator, or air conditioning system. Higher efficiency, less energy (power) usage, and thus reduced operational costs are all related to higher COPs. What is the relationship between the C.O.P. of a heat pump and the efficiency of a heat engine? A) E equals (C.O.P.) B) E equals 1 / (C.O.P.) Considering that E = W / Q, the Carnot engine's equivalent is (T2 - T1) / T2. The temperature of the environment to which the freezer rejects heat is if the internal temperature is less than 200C.

To learn more about refrigerator's click the link below:

brainly.com/question/13002119

#SPJ4

The composite plate is made from both steel (A) and brass (B) segments. Take ?st = 7.85 Mg/m3 and ?br = 8.74 Mg/m3. Suppose that L = 160 mm . (Figure 1)
Determine the mass. Determine location (x¯, y¯, z¯) of its mass center G.

Answers

Mass of composite plate is 8.092 Mg and location (x, y, z) of its mass center G is:

x = 76 mm

y = 0

z = 0

What is Mass of a composite plate?

The mass of the composite plate can be determined by finding the mass of each component (steel and brass) and then adding them together.

Since we know the densities of both materials (st = 7.85 Mg/m3 and br = 8.74 Mg/m3), we can calculate the mass of each component.

For steel, we multiply the density by the area:

Mass of steel = (0.2)(7.85) = 1.57 Mg

For brass, we multiply the density by the area:

Mass of brass = (0.8)(8.74) = 6.992 Mg

Now add the two masses together:

Mass = A.st + B.br = 1.57 + 6.992 = 8.092 Mg

The location of the mass center (G) can then be determined using the formula:

x¯ = (A.Axbar) + (B.Bxbar) = (0.2)(100) + (0.8)(60) = 76 mm

y¯ = (A.Aybar) + (B.Bybar) = (0.2)(0) + (0.8)(0) = 0 mm

z¯ = (A.Azbar) + (B.Bzbar) = (0.2)(0) + (0.8)(0) = 0 mm

These values give us the location of the mass center G.

To learn more about composite plate refer :

https://brainly.com/question/13151130

#SPJ4

The factorial of a non-negative integer n, denoted by n!, is the product of all positive integers less than or equal to n For example, 5 ! = 5 x 4 x 3 x 2 x 1 = 120. The value of 0! is 1. Write a program, with comments, to do the following: 20 points Ask the user to enter a positive integer n. between 1 and 20 ; You may assume the user will enter a valid input Calculate the factorial of all numbers j (1 < j < n) from 1 - n (inclusive) For each j, print the value of j and j! with a suitable message and append each j! to a list called factorial list. Print the final factorial list with a suitable message Write function cal that takes the enter n and returns the factorial value, also act num write another function to print the factorial_list? -== RESTART: C:/Users/sanjay/Desktop/13.py= Please enter a positive integer between 1 and 20: 5 j = j = j 1 1 ! 1 = 2 2 2 3; 3 6 4 ! 24 j=4; = j =5 factorial_list = 5 ! 120 = [1, 2, 6, 24, 1201 > -== RESTART: C:/Users/sanjay/Desktop/13.py Please enter a positive integer between 1 and 20: 10 j = j = 1 1 ! 1 = 2: 2 ! 2 = 3 3 6 4 4 ! 24 = 5 ! j = 5 120 = 6 6 720 j = 7 7 5040 = 8 8 40320 = j = 9 j = 9! 362880 10 10 3628800 factorial list [1, 2, 6, 24, 120, 720, 5040, 40320, 362880, 3628800] = >

Answers

def cal(n): factorial = 1 for i in range(1, n+1): factorial = factorial * i return factorial def print_factorial_list(n): 'Prints the factorial list of the numbers from 1 to n' factorial_list = [] fοr j in range(1, n+1): factorial = cal(j) factorial_list.append(factorial) print("j = {}; j! = {}".format(j,factorial)) print("factorial list = {}".format(factorial_list)) n = int(input("Please enter a positive integer between 1 and 20: ")) print_factorial_list(n)

What is Python programming ?

High-level, interpreted Python is a general-purpose programming language that is easy to learn and use. Frequently used for automation and scripting, it is an easy-to-read object-oriented programming language.

Web development, data analysis, and artificial intelligence are just a few of the applications that people choose Python for.

It offers a broad selection of features, libraries, and frameworks that make it a strong option for numerous different kinds of development projects.

in this question

This is a program written in Python, a high-level, interpreted, and general-purpose programming language.

Steps:

1. Define a function called 'cal' that takes a number, n, as a parameter and returns the factorial value of n. The factorial of a number is calculated by multiplying all the integers from 1 to n.

2. Define a function called 'print_factorial_list' that takes a number, n, as a parameter and prints the factorial list of the numbers from 1 to n. This is done by looping over each number from 1 to n and calculating the factorial of each number and then appending it to a list called 'factorial_list'.

3. Ask the user to enter a positive integer n between 1 and 20.

4. Call the function 'print_factorial_list' with the user input, n, as the argument.

5. Print the factorial list with a suitable message.

Learn more about Python programming

https://brainly.com/question/19792191

#SPJ4

according to the tia chapter 1, which of the following are points and counterpoints regarding automated robotic machinery? (select all that apply.)

Answers

Creating robot swarms, enhancing navigation and exploration, and creating artificial intelligence that can "learn how to learn" and apply common sense to moral and social judgments are three tasks that concentrate on fundamental issues in robotics.

Which issues in robotics are the most pressing?

Some of the key challenges that are currently resonating throughout the sector are data privacy and security. To complete their tasks, robots also require a variety of personal information and process sensitive data. The robot may utilize this private data in any way, but there is no way to know for sure.

What constitutes robots' primary flaw?

Robots are frequently very expensive to purchase, maintain, require extra parts, and require programming to do the work. This is true of both the initial cost and ongoing costs.

To know more about robotic machinery visit:-

https://brainly.com/question/4130302

#SPJ4

canada has proposed an action plan to address climate change and air pollution. the action plan will reduce the impact of greenhouse gases and pollutants on the environment and human health. which of the following claims about the canadian action plan is best supported by the data in the graph? responses the plan encourages the transition from electricity generation from nuclear power to electricity generation from cleaner-burning natural gas. the plan encourages the transition from electricity generation from nuclear power to electricity generation from cleaner-burning natural gas. the plan focuses on increasing regulation on installation and maintenance of catalytic converters in vehicle exhaust systems. the plan focuses on increasing regulation on installation and maintenance of catalytic converters in vehicle exhaust systems. the plan supports phasing out traditional coal power plants and transitioning to sources like hydroelectricity, wind, and solar power. the plan supports phasing out traditional coal power plants and transitioning to sources like hydroelectricity, wind, and solar power. the plan provides a strategy for reducing the amount of plastic wastes in landfills through the production of long-lasting and durable plastics.

Answers

The plan supports phasing out traditional coal power plants and transitioning to sources like hydroelectricity, wind, and solar power is best supported by the data in the graph.

What is hydroelectricity?
Hydroelectricity is a type of renewable energy that is generated by the movement of water. It is created by capturing the kinetic energy of the moving water and converting it to electrical energy. This is done by building dams on rivers or streams and using the pressure created by the water to turn turbines, which are connected to generators that transform the energy into electricity. This electricity can then be used to power homes and businesses.

The graph shows that the Canadian plan encourages the transition from electricity generation from nuclear power, coal, and oil to cleaner-burning natural gas, hydro, wind, and solar energy sources. This clearly demonstrates that the plan supports phasing out traditional coal power plants and transitioning to sources like hydroelectricity, wind, and solar power.

To learn more about hydroelectricity

https://brainly.com/question/15570084

#SPJ4

Other Questions
Suppose f(x) is continuous and defined for all real numbers. You are given that f(x) has critical points at x = -1 and x = 0. If f'(x) is positive in the interval x < -1, negative in the interval -1 < x < 0, and positive in the interval x > 0, is the point where x = -1 the location of a relative maximum, minimum, or neither? Maximum Minimum Neither An angle measures 69.2 less than the measure of its complementary angle. What is the measure of each angle? What are the 4 methods in solving quadratic equation?. with which of the following models do many users share a certain amount of bandwidth until the transmissions reach the isp's core network ? What religion became the dominant religion of Vietnam?O HinduismO ChristianityO BuddhismO Islam What role does the authors use of figurative language play in developing the theme ? What evidence from the text supports your answer? What are Alices main concerns in the text aristotle's golden mean defines moral virtue as a middle state determined by practical wisdom that emphasizes moderation and temperance.T/F x + y = 55y=6Its simultaneous equationsIt would really help PTC is a substance that has a strong bitter taste for some people and is tasteless for others. The ability to taste PTC is inherited. About 75% of Italians can taste PTC, for example. You want to estimate the proportion of Americans with at least one Italian grandparent who can taste PTC. (a) Starting with the 75% estimate for Italians, how large a sample must you collect in order to estimate the proportion of PTC tasters within ????0.04 with 90% confidence? (b) Estimate the sample size required if you made no assumptions about the value of the proportion who could taste PTC. How much has the required sample size changed? Portuguese traders were the first Europeans to establish trade routes in what continent in the Eastern Hemisphere? how many different ways are there to arrange the letters in the following words? 1. (6 points) mississauga Baed on the information in the twin tudie, what can we predict about the likelihood of identical twin inheriting Alzheimer' dieae? 1) Taking credit for others work: You and a coworker were assigned a project to complete. When starting the project you divided the responsibilities so the project could be completed efficiently. After starting on the project, you got sidetracked and didn't complete your portion of the project. Your coworker completed your work and her work so that the project would get finished in time. Your supervisor loved the work and complemented both of you on a job well done. What is the ethical choice for you? income elasticity of demand is the extent to which the demand in the quantity of goods responds to changes in What is the brief summary of the story Pyramus and Thisbe?. 10. Higher Order Thinking Consider the functionsg(x) = 2x + 1 and h(x) = 2x + 2 for the domain0 < x < 5.a. Without evaluating or graphing the functions, how do the ranges compare? 4.8d=2.4 plsss help I'm crying What did Farmers Alliance proposed to get some federal protection?. discuss why you would use a for loop versus a while loop.