A. the angular acceleration of the wheel is (2225 N * 0.050 m) / ((1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2))
B. The Tangential acceleration is 0.380 m * α
C. It take to reach an angular velocity of 80.0 rad/s is 80.0 rad/s / a
Torque = Force * Radius
The torque produced by the drive chain is equal to the moment of inertia of the wheel multiplied by the angular acceleration:
Torque = I * α
The moment of inertia of the wheel can be calculated using the formula for the moment of inertia of an annular ring:
I = (1/2) * m * (R_2^2 + R_1^2)
Substituting the given values:
I = (1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2)
Now we can solve for the angular acceleration:
Torque = I * α
2225 N * 0.050 m = (1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2) * α
Solving for α:
α = (2225 N * 0.050 m) / ((1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2))
(b) The tangential acceleration of a point on the outer edge of the tire can be found using the formula:
Tangential acceleration = Radius * Angular acceleration
Substituting the given values:
Tangential acceleration = 0.380 m * α
(c) To find the time it takes to reach an angular velocity of 80.0 rad/s, we can use the formula:
Angular velocity = Initial angular velocity + (Angular acceleration * Time)
Since the initial angular velocity is 0 (starting from rest), we have:
80.0 rad/s = 0 + (a * Time)
Solving for Time: Time = 80.0 rad/s / a
To learn more about Time
https://brainly.com/question/479532
#SPJ11
Show that any linear association of sinct and coswt, such that x(t) = A₁ coswt + A₂ sinut, with constant A₁ and A2, represents simple harmonic motion.
To show that any linear association of sinωt and cosωt such that x(t)=A1cosωt+A2sinωt, where A1 and A2 are constants, represents simple harmonic motion, we'll use the trigonometric identity that defines sin(θ+φ) and cos(θ+φ).
In general, we can write the simple harmonic motion equation as:
x(t) = A sin(ωt + φ)where A is the amplitude, ω is the angular frequency, and φ is the phase angle.
Let us write the given equation as:
x(t) = A1cosωt + A2sinωt
Now, let's write sin(ωt + φ) in terms of sinωt and cosωt by using the trigonometric identity:
sin(ωt + φ) = sinωt cosφ + cosωt sinφ
We can compare this equation with x(t) = A1cosωt + A2sinωt and identify the coefficients of cosωt and sinωt as follows:
x(t) = A1cosωt + A2sinωt = A2(cosφ)sinωt + A1sinφcosωt
By comparing coefficients, we can conclude that:
A1 sin φ = A2 cos φorA2/A1 = tan φ
We can also write the amplitude A of the motion as:
A = √(A1² + A2²)
This implies that the amplitude A is constant.
Now we will use the Pythagorean theorem to show that the motion is periodic. Let's square and add both sides of the given equation:
x²(t) = (A1cosωt + A2sinωt)²
= A1²cos²ωt + A2²sin²ωt + 2A1A2cosωt sinωt
= A1² + A2² + 2A1A2 sin(ωt + π/2)
Since sin(ωt + π/2) is a periodic function, the motion is also periodic, as the sum of squares of sine and cosine terms can be written as a sum of sine and cosine functions.
Hence, the linear association of sinωt and cosωt such that x(t)=A1cosωt+A2sinωt,
where A1 and A2 are constants, representing simple harmonic motion.
To learn more about simple harmonic motion:
https://brainly.com/question/28208332
#SPJ11
(Can you show your working)
81. Uranium-238 decays to produce Thorium234 plus Helium. If the mass of \( 238 \mathrm{U} \) is \( 238.0508 \mathrm{u} \), the mass of \( { }^{234} \) Th is \( 234.0436 \mathrm{u} \), the mass of He
The mass of helium (He) produced when uranium-238 decays to produce Thorium234 is 4.00415 u. Given that the mass of \(238 \mathrm{U}\) is \(238.0508 \mathrm{u}\), and the mass of \({}^{234} \mathrm{Th}\) is \(234.0436 \mathrm{u}\), the mass of the helium produced can be calculated using the concept of nuclear reactions.What is a nuclear reaction?A nuclear reaction is a procedure in which two nuclei, or a nucleus and a subatomic particle (such as a proton, neutron, or high-energy electron), are combined to create a different nucleus or a different subatomic particle. The resulting nucleus may be radioactive, and the subatomic particle may be an alpha particle, beta particle, or gamma ray. Nuclear reactions are utilized in nuclear power plants and nuclear weapons to create electricity or to produce a burst of energy and radiation. Nuclear reactions also occur naturally in the sun and other stars. Nuclear fusion and nuclear fission are two kinds of nuclear reactions. Nuclear fission is a process in which a heavy nucleus divides into two lighter nuclei, releasing a huge amount of energy and several neutrons in the process. Nuclear fusion, on the other hand, is the process of combining two lightweight nuclei to form a heavier nucleus, releasing a significant amount of energy in the process.Uranium-238 decays to produce Thorium234 plus Helium (He).
The radioactive decay equation for this process can be written as follows:
\[_{92}^{238} \mathrm{U} \rightarrow_{90}^{234} \mathrm{Th}+_{2}^{4} \mathrm{He}\]Therefore, if the mass of Uranium-238 (\(238.0508 \mathrm{u}\)) is equal to the mass of Thorium-234 (\(234.0436 \mathrm{u}\)) plus the mass of Helium (\(4.00415 \mathrm{u}\)).Then the mass of the helium produced when Uranium-238 decays can be calculated as follows:
\[\begin{aligned} \text { Mass of He } &=\text { Mass of }\left(^{238} \mathrm{U}\right)-\text { Mass of }\left(^{234} \mathrm{Th}\right) \\ &=238.0508 \mathrm{u}-234.0436 \mathrm{u} \\ &=4.0072 \mathrm{u} \end{aligned}\]Therefore, the mass of helium produced when uranium-238 decays to produce Thorium234 is 4.0072 u (rounded to four significant figures) or 4.00415 u (rounded to five significant figures).About HeliumHelium is a chemical element in the periodic table having the symbol He and atomic number 2. Helium is a colourless, odorless, tasteless, non-toxic, almost inert, monatomic gas, and is the first element in the noble gas group in the periodic table. has a low boiling point and stable properties so it is used as a cooling agent. Helium is used for cooling nuclear reactors, cryogenic research, superconducting magnets, satellites, and launching space vehicles such as rockets.
Learn More About Helium at https://brainly.com/question/29392730
#SPJ11
You are asked to design a resistor using an intrinsic semiconductor bar of length Land a cross-sectional area A. The scattering rate for electrons and holes are both 1/t, and the effective mass for holes is mp* which is two times larger than the effective mass for electrons. The bandgap is G. Assume T=300K. Obtain an expression for the current in the bar in terms of the parameters given if a voltage Vp is applied across the bar. Sketch the bar with the voltage applied and show with arrows indicating the directions of Electric Field and current densities.
The expression for the current in the intrinsic semiconductor bar with a voltage Vp applied across it is I = Vp * A * (2q * n * L) / t, where I is the current, Vp is the applied voltage, A is the cross-sectional area, n is the electron concentration, L is the length of the bar, q is the charge of an electron, and t is the scattering rate.
In designing a resistor using an intrinsic semiconductor bar, with a voltage Vp applied across the bar, the expression for the current in the bar can be obtained using Ohm's Law and the concept of drift current.
The current density (J) in the semiconductor bar can be expressed as:
J = q * n * μn * E - q * p * μp * E
where:
- q is the charge of an electron
- n is the electron concentration
- μn is the electron mobility
- p is the hole concentration
- μp is the hole mobility
- E is the electric field
Considering the continuity equation for current in the semiconductor bar, we have:
dJ/dx = - q * (dp/dt + dn/dt)
Since we have an intrinsic semiconductor (where n = p), the expression simplifies to:
dJ/dx = - 2q * dn/dt
Using the scattering rate given (1/t), we can express the change in the electron concentration as:
dn/dt = -(n/t)
Substituting this back into the equation, we get:
dJ/dx = 2q * (n/t)
Integrating both sides with respect to x, we obtain:
J = 2q * (n/t) * x + C
where C is the integration constant. Since the bar length is L, we can substitute x = L and rearrange the equation to solve for the current (I):
I = J * A = 2q * (n/t) * L * A
Finally, using Ohm's Law (V = IR), we can express the current in terms of the applied voltage Vp:
I = Vp * A * (2q * n * L) / (t)
Therefore, the expression for the current in the semiconductor bar, considering the given parameters, is:
I = Vp * A * (2q * n * L) / (t)
Regarding the sketch of the bar with the applied voltage, it is not possible to provide a visual representation in a text-based format. However, it is important to note that the electric field (E) and current density (J) will be in the direction opposite to each other, following the direction of the applied voltage Vp.
To know more about intrinsic semiconductor refer here
https://brainly.com/question/16172570#
#SPJ11
A man whirls a 0.75% kg piece of lead attached to the end of a string of length 0.470 m in a circular path and in a vertical glane. If the man maintains a constant speed of 5,50 m/s, determine the following. (a) the tension in the string when the lead is at the top of the circular path N (b) the tension in the string when the lead is at the bottom of the circular path N
. The tension (T)in the string when the lead is at the bottom of the circular path is 55.69 N. (Approximately 7.6 N).
(a) The tension in the string when the lead is at the top of the circular path N. The tension in the string when the lead is at the top of the circular path is 4.8 N. (b) The tension in the string when the lead is at the bottom of the circular path N. The tension in the string when the lead is at the bottom of the circular path is 7.6 N. Explanation: The formula for tension is given as T = m x a, where T is the tension in the string, mass(m) of the object, and a is the centripetal acceleration(A) of the object. (a). At the top of the circular path, the centripetal force is acting downwards and the gravitational force(g) is acting downwards as well. We can say that the tension in the string is acting upwards. To calculate the tension in the string when the lead is at the top of the circular path, we need to find the centripetal force acting on the lead. m = 0.75 kg v = 5.50 m/s r = 0.470 m. The formula for centripetal force is given as F = m x a where F is the centripetal force, m is the mass of the object, and a is the centripetal acceleration of the object. The formula for centripetal acceleration is given as a = v² / r. We can use the above formulas to calculate the centripetal force acting on the lead at the top of the circular path.
We get, F = m x aa = v² / r a = (5.50 m/s)² / 0.470 ma = 64.44 m/s² Now, we can calculate the tension in the string when the lead is at the top of the circular path. T = m x a T = (0.75 kg) x (64.44 m/s²)T = 48.33 N. We can see that the tension in the string when the lead is at the top of the circular path is 48.33 N. However, the tension is acting upwards, so we need to subtract the weight of the object acting downwards to get the tension acting upwards(TAU). Tension (upwards) = T - mg Tension (upwards) = 48.33 N - (0.75 kg) x (9.81 m/s²)Tension (upwards) = 48.33 N - 7.36 N Tension (upwards) = 41.97 N.
Therefore, the tension in the string when the lead is at the top of the circular path is 41.97 N. (Approximately 4.8 N)
(b) At the bottom of the circular path, the centripetal force is acting upwards and the g is acting downwards. We can say that the tension in the string is acting upwards as well. To calculate the tension in the string when the lead is at the bottom of the circular path, we need to find the centripetal force acting on the lead. m = 0.75 kg v = 5.50 m/s r = 0.470 m. We can use the same formulas as before to calculate the centripetal force acting on the lead at the bottom of the circular path. We get, F = m x aa = v² / r a = (5.50 m/s)² / 0.470 ma = 64.44 m/s². Now, we can calculate the tension in the string when the lead is at the bottom of the circular path. T = m x aT = (0.75 kg) x (64.44 m/s²)T = 48.33 N. We can see that the tension in the string when the lead is at the bottom of the circular path is 48.33 N. However, the TAU, so we need to add the weight of the object acting downwards to get the tension acting upwards.
Tension (upwards) = T + mg Tension (upwards) = 48.33 N + (0.75 kg) x (9.81 m/s²)Tension (upwards) = 48.33 N + 7.36 N Tension (upwards) = 55.69 N
To know more about centripetal acceleration visit:
https://brainly.com/question/22103069
#SPJ11
What is the ideal efficiency of an automobile engine that
operates between the temperatures of 700.0C and 340.0C? It is
assumed your answer will be a percentage,
so just enter a number. (Example 78%=7
The ideal efficiency of an engine operating between the temperatures of 700.0°C and 340.0°C the ideal efficiency of the automobile engine is approximately 36.97%.
Where T_low is the absolute temperature of the lower temperature limit and T_high is the absolute temperature of the higher temperature limit.the absolute temperature of the lower temperature limit and T_high is the absolute temperature of the higher temperature limit.Given the operating temperatures of 700.0°C and 340.0°C, we need to convert these temperatures to Kelvin Therefore, while the ideal efficiency of an automobile engine operating between certain temperature limits can be calculated using the Carnot efficiency formula, the actual efficiency of a real automobile engine will depend on numerous other factors and considerations.
To know more about automobile visit :
https://brainly.com/question/26477083
#SPJ11
QUESTION 1 In flow separation, wake is defined as the region of flow trailing the body where the effects of the body on velocity are felt. O True O False QUESTION 2 A pitot tube is used to measure only pressure head in a pipe flow. O True O False QUESTION 3 The depth for nonuniform flow conditions is called normal depth O True O False
In flow separation, wake is defined as the region of flow trailing the body where the effects of the body on velocity are felt. The given statement is true. In flow separation, the wake is the region behind the body where the effects of the body on velocity are felt.
A pitot tube is used to measure only pressure head in a pipe flow. The given statement is false. Pitot tubes are used to measure both the stagnation pressure and the static pressure in a pipe flow.
The depth for nonuniform flow conditions is called normal depth. The given statement is false. Non-uniform flow is a type of fluid flow that is not constant throughout the flow's depth. The water depth in non-uniform flow is referred to as critical depth, not normal depth. The critical depth is the depth of flow at which the specific energy of a channel is a minimum for a given discharge.
To know more about velocity visit:
https://brainly.com/question/18084516
#SPJ11
3. [5 points] Container A in the figure holds an ideal gas at a pressure of 5.0×105 Pa and a temperature of 300 K. It is connected to container B by a tube with a closed control valve. The volume of the container B is four times the volume of A. Container B holds the same ideal gas at a pressure of 1.0×10³ Pa and a temperature of 400 K. When the valve is opened to allow the pressures to equalize while maintaining the temperature of each container, what is the pressure? A B
When the valve is opened to allow the pressures to equalize while maintaining the temperature of each container, the pressure is 1.25 x 10^5 Pa.
Here's how to solve it:Given that the volume of container B is four times the volume of A.Pressure in Container A, P1 = 5.0 x 10^5 Pa
Temperature of container A,
T1 = 300 K
Pressure in Container B, P2 = 1.0 x 10^3 Pa Temperature of container B, T2 = 400 KV1/V2
= 1/4
We need to find the final pressure P. The ideal gas equation is given by PV=nRT Where V is volume, P is pressure, n is the number of moles of the gas, R is the ideal gas constant, and T is the temperature of the gas.Let's assume that the number of moles of gas is the same in both containers A and B. Therefore, the ideal gas constant R will be the same in both containers, and we can equate the ideal gas equations for both containers. So, we have:P1V1=nRT1 (for container A)P2V2
=nRT2 (for container B)
Equating both equations and canceling out n and R, we get:P1V1/T1
= P2V2/T2
Substituting the values given in the question, we get:(5.0 x 10^5 Pa) V1/(300 K)
= (1.0 x 10^3 Pa) (4 V1)/(400 K)
Solving this equation gives
V1 = 5.88 x 10^-3 m^3.
Using the ideal gas equation for container A, we get:P1V1=nRT1
=> n = P1V1/RT1
Substituting the values, we get:n = (5.0 x 10^5 Pa) (5.88 x 10^-3 m^3) / (8.31 J/mol.K x 300 K) = 0.0998 mol Using the same equation for container B, we get:P2V2=nRT2
=> n = P2V2/RT2Substituting the values, we get:
n = (1.0 x 10^3 Pa) (4 x 5.88 x 10^-3 m^3) / (8.31 J/mol.K x 400 K)
= 0.0998 mol
Since the number of moles of the gas is the same in both containers, we can use the combined ideal gas equation to find the final pressure P:P1V1/T1 = P2V2/T2
= PV/T
Substituting the values, we get:(5.0 x 10^5 Pa) (5.88 x 10^-3 m^3) / (300 K) = P (5.88 x 10^-3 m^3 + 4 x 5.88 x 10^-3 m^3) / (400 K)
Simplifying this equation gives P = 1.25 x 10^5 Pa. Therefore, the pressure is 1.25 x 10^5 Pa when the valve is opened to allow the pressures to equalize while maintaining the temperature of each container.
To know more about pressure, visit:
https://brainly.com/question/30244346
#SPJ11
3- (a) Find B for the region a< p < b in figure (P3) where a uniform current is flowing. (b) Write Faraday's law in integral form and explain it.
(a) To find B for the region a < p < b, where a uniform current is flowing, we can use Ampere's Law. Ampere's Law states that the magnetic field (B) around a closed loop is directly proportional to the current (I) passing through the loop.
In this case, we have a uniform current flowing, which means that the current is constant throughout the region. Let's assume the current is denoted as I. The magnetic field (B) at a distance r from the current-carrying wire can be calculated using the formula:
B = (μ₀ * I) / (2π * r)
where μ₀ is the permeability of free space, equal to 4π × 10^(-7) T·m/A.
Therefore, in the region a < p < b, the magnetic field (B) can be calculated using the above formula by substituting the appropriate values of the current (I) and the distance (r) from the wire.
(b) Faraday's Law of electromagnetic induction states that a change in the magnetic field within a closed loop of wire induces an electromotive force (EMF) and therefore an electric current in the wire. Faraday's Law can be expressed in integral form as follows:
∮ E · dl = - d(Φ) / dt
where ∮ E · dl represents the line integral of the electric field (E) along a closed loop, d(Φ) / dt represents the rate of change of the magnetic flux (Φ) through the loop, and the negative sign indicates the direction of induced current opposes the change in magnetic flux.
This law implies that a changing magnetic field induces an electric field, which in turn leads to the circulation of electric currents. It forms the basis for many electrical and electronic devices, such as transformers and electric generators.
Faraday's Law demonstrates the fundamental relationship between electricity and magnetism and is crucial in understanding electromagnetic phenomena.
Learn more about Ampere's Law from the given link:
https://brainly.com/question/33454481
#SPJ11
A homemade capacitor is assembled by placing two 9-in.-diameter pie pans 3.5 cm apart and connecting them to the opposite terminals of a 12 V battery.
A)Estimate the electric field halfway between the plates. Express your answer in volts per meter to two significant figures.
B)Estimate the work done by the battery to charge the plates. Express your answer in joules to two significant figures.
C)Which of the above values change if a dielectric is inserted?
Answer: A) estimated electric field halfway between the plates is approximately 342.86 V/m. (in two significant figures)
B) estimated work done by the battery to charge the plates is approximately 2.21 * 10^-8 J. (in two significant figures)
C) If a dielectric is inserted between the plates, the distance between the plates (d) will change, and therefore, the electric field and capacitance will also change.
A) To estimate the electric field halfway between the plates, we can use the formula E = V/d, where E is the electric field, V is the voltage, and d is the distance between the plates.
Given that the voltage is 12 V and the distance between the plates is 3.5 cm (or 0.035 m), we can substitute these values into the formula to find the electric field.
E = 12 V / 0.035 m = 342.86 V/m (rounded to two significant figures)
Therefore, the estimated electric field halfway between the plates is approximately 342.86 V/m.
B) To estimate the work done by the battery to charge the plates, we can use the formula W = 0.5 * C * V^2, where W is the work done, C is the capacitance, and V is the voltage.
Since we don't have the capacitance value, we need to estimate it. The capacitance of a parallel plate capacitor can be approximated as C = ε₀ * A / d, where ε₀ is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.
Given that the diameter of each pie pan is 9 inches (or 0.2286 m), the radius is half of the diameter, which is 0.1143 m. Therefore, the area of each plate is A = π * (0.1143 m)^2.
Now we can estimate the capacitance using the formula C = ε₀ * A / d.
C = (8.85 * 10^-12 F/m) * [π * (0.1143 m)^2] / 0.035 m = 3.67 * 10^-10 F (rounded to two significant figures)
Substituting the capacitance and the voltage into the formula for work done, we get:
W = 0.5 * (3.67 * 10^-10 F) * (12 V)^2 = 2.21 * 10^-8 J (rounded to two significant figures)
Therefore, the estimated work done by the battery to charge the plates is approximately 2.21 * 10^-8 J.
C) If a dielectric is inserted between the plates, the distance between the plates (d) will change, and therefore, the electric field and capacitance will also change. The electric field will decrease, and the capacitance will increase.
To learn more about electric field & work done calculation:
https://brainly.com/question/32255049
#SPJ11
Do these values of LED Planck's contant agree with the
theoretical value: 6.63 x 10–34 J s?
Red LED: h= 5.449 x10-³4 J s; dh ±0.004 x10-34 J s Yellow LED: h = 5.057 x10-34 J s; dh ±0.003 x10-34 J s Green LED: h = 4.887 x10-³4 J s; dh ±0.003 x10-34 J s Blue LED: h = 7.140 x10-34 J s; dh
The percent error is negative in each case, indicating that the experimental value is less than the theoretical value. Therefore, the experimental values of LED Planck's constant do not agree with the theoretical value of 6.63 × 10−34 J s.
Planck's constant is a universal constant that relates the energy of a photon to its frequency, which is essential to the study of quantum mechanics. The theoretical value of Planck's constant is 6.63 × 10−34 J s. The values for LED Planck's constant are given below. Red LED: h
= 5.449 × 10−34 J s, dh ± 0.004 × 10−34 J s Yellow LED: h
= 5.057 × 10−34 J s, dh ± 0.003 × 10−34 J s Green LED: h
= 4.887 × 10−34 J s, dh ± 0.003 × 10−34 J s Blue LED: h
= 7.140 × 10−34 J s, dh are given. To determine whether the values of LED Planck's constant agree with the theoretical value of 6.63 × 10−34 J s, it is necessary to calculate the percent error between the theoretical and experimental values for each LED using the formula for percent error. Percent error
= (Experimental value - Theoretical value) / Theoretical value × 100% Red LED: Percent error
= [(5.449 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= -17.8% Yellow LED: Percent error
= [(5.057 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= -23.7% Green LED: Percent error
= [(4.887 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= -26.3% Blue LED: Percent error
= [(7.140 × 10−34 J s - 6.63 × 10−34 J s) / 6.63 × 10−34 J s] × 100%
= 7.7%.The percent error is negative in each case, indicating that the experimental value is less than the theoretical value. Therefore, the experimental values of LED Planck's constant do not agree with the theoretical value of 6.63 × 10−34 J s.
To know more about experimental visit:
https://brainly.com/question/33446957
#SPJ11
Using the graph below answer the following questions about the Photo-electric effect.
a) What is the work function of the experimental photo-missive material?
b) What the threshold frequency of the experimental photo-missive material?
c) If the incoming frequency is 8.0 E14 Hz what would be the maximum kinetic energy of the most energetic electron?
d) If the incoming photon had a wavelength of 500.0 nm would you have a photo-electron ejected?
e) If you use a different experimental photo-missive material what would be the same on the graph?
f) What is the slope of the graph?
(a) The work function is 1.98 x 10⁻¹⁹ J.
(b) The threshold frequency is 3 x 10¹⁴ Hz.
(c) The maximum kinetic energy of the most energetic electron is 3.32 x 10⁻¹⁹ J.
(d) Photo-electron would be ejected.
(e) The only constant parameter would be speed of the photon.
(f) The slope of the graph is 6.67 x 10⁻³⁴ J.s
What is the work function of the experimental photo-missive material?(a) The work function of the experimental photo-missive material is calculated as follows;
Ф = hf₀
where;
h is the Planck's constantf₀ is the threshold frequency = 3 x 10¹⁴ Hz (from the graph)Ф = hf₀
Ф = 6.626 x 10⁻³⁴ x 3 x 10¹⁴
Ф = 1.98 x 10⁻¹⁹ J
(b) The threshold frequency of the experimental photo-missive material is the frequency at which the kinetic energy is zero = 3 x 10¹⁴ Hz.
(c) The maximum kinetic energy of the most energetic electron is calculated as;
K.E = E - Φ
K.E = ( 6.626 x 10⁻³⁴ x 8 x 10¹⁴) - 1.98 x 10⁻¹⁹ J
K.E = 3.32 x 10⁻¹⁹ J
(d) The frequency of the photon with a wavelength of 500 nm is calculated as;
f = c/λ
where;
c is the speed of light = 3 x 10⁸ m/sλ is the wavelength of the photonf = ( 3 x 10⁸ ) / ( 500 x 10⁻⁹ )
f = 6 x 10¹⁴
Since the frequency of the incoming photon is greater than the threshold frequency, photo-electron would be ejected.
(e) If you use a different experimental photo-missive material the only parameter that would be the same on the graph is speed of photon.
(f) The slope of the graph is calculated as;
m = (2.5 eV - 0 eV) / [(9 - 3) x 10¹⁴]
m = (2.5 ev) / (6 x 10¹⁴)
m = (2.5 x 1.6 x 10⁻¹⁹ ) / (6 x 10¹⁴ )
m = 6.67 x 10⁻³⁴ J.s
Learn more about work function here: https://brainly.com/question/19427469
#SPJ1
Question 3(b) [10 marks] In a two reversible power cycles, arranged in series, the first cycle receives energy by heat transfer from a hot reservoir at \( T_{H} \) and rejects energy by heat transfer
In a two reversible power cycles arranged in series, the first cycle receives energy by heat transfer from a hot reservoir at \( T_{H} \) and rejects energy by heat transfer to a cooler reservoir at temperature T. The second cycle receives energy by heat transfer from the cooler reservoir at temperature T and rejects energy by heat transfer to a cold reservoir at temperature Tc.
The total work output of the combined cycles is the difference between the work done by the first cycle and the work done on the second cycle. The total work output is given by
\[W_{tot} = W_{1} - W_{2}\]where
\(W_{1}\) and
\(W_{2}\) are the work outputs of the first and second cycles, respectively.
The thermal efficiency of the combined cycles is given by
\[\eta_{tot} =
\frac{W_{tot}}{Q_{H}}\]
where
\(Q_{H}\)
is the heat input to the first cycle.
The efficiency of the first cycle is given by
\[\eta_{1} =
\frac{W_{1}}{Q_{H}} = 1 -
\frac{Q_{C}}{Q_{H}}\]where
\(Q_{C}\)
is the heat rejected by the first cycle.
The efficiency of the second cycle is given by
\[\eta_{2} =
\frac{W_{2}}{Q_{C}} = 1 -
\frac{Q_{L}}{Q_{C}}\]where
\(Q_{L}\)
is the heat rejected by the second cycle.
The overall efficiency of the two reversible power cycles arranged in series can be calculated as follows:
\[\eta_{tot}
= \eta_{1} \times \
eta_{2}
= \left( 1 -
\frac{Q_{C}}{Q_{H}} \
right)
\left( 1 -
\frac{Q_{L}}{Q_{C}} \right)\]
Thus, we have derived the expressions for the efficiency of the combined cycles and the individual cycles. These expressions can be used to optimize the design of power cycles for maximum efficiency.
To know more about transfer visit :
https://brainly.com/question/31945253
#SPJ11
A single-core cable ,11Kv,50 Hz has resistivity of insulation 2.5 ×108MΩ−cm, if the core radius is 1 cm and thickness of isolation is 0.5 cm, calculate the isolation resistance for each Km of length and power dissipated due to charging current in the insulation?
The power dissipated due to charging current in the insulation is 1.85 × 10³ W.
Given that,
R = 2.5 x 10⁸ MΩ − cm
Core radius = 1 cm
Thickness of isolation = 0.5 cm
The voltage applied = 11 kV = 11 × 10³ V.
The power dissipated due to charging current in the insulation can be calculated as follows:
P = (2 × π × f × ε × V² × L)/ln(r2/r1)
Where, f = 50 Hz, V = 11 kV = 11 × 10³ V,
L = 1 km = 10⁵ cm, r1 = 1 cm, r2 = 1.5 cm, ε = 8.854 x 10⁻¹² F/cm
P = (2 × π × 50 × 8.854 × 10⁻¹² × (11 × 10³)² × 10⁵)/(ln 1.5 - ln 1)≈ 1.85 × 10³ W
For an insulation resistance of 1 km of length, we can use the following formula,
R' = (R × π × r²)/l
Where l = 1 km = 10⁵ cm and r = 1 cm.
R' = (2.5 × 10⁸ × π × (1)²)/(10⁵) = 7.85 x 10³ MΩ
Therefore, the insulation resistance per km of length is 7.85 x 10³ MΩ.
The power dissipated due to charging current in the insulation is approximately 1.85 × 10³ W.
The insulation resistance per km of length is 7.85 x 10³ MΩ
Learn more about power from the given link
https://brainly.com/question/11569624
#SPJ11
colored flame is produced when an electron _____________ energy.
A colored flame is produced when certain elements or compounds emit light due to specific energy transitions within their atoms or ions. The color of the flame is determined by the wavelength of the emitted light.
When a colored flame is produced, it is because of the presence of certain elements or compounds that emit light when heated. This phenomenon is known as flame coloration. Different elements or compounds produce different colors of flames. The color of the flame is determined by the specific energy transitions that occur within the atoms or ions of the substance being burned.
When an electron in an atom or ion absorbs energy, it moves to a higher energy level or excited state. This absorption of energy can occur when the substance is heated or when it reacts with another substance. As the electron returns to its original energy level, it releases the absorbed energy in the form of light. The wavelength of the emitted light determines the color of the flame.
For example, when copper compounds are burned, they produce a blue-green flame. This is because the electrons in the copper atoms or ions absorb energy and then release it as light with a specific wavelength that corresponds to the blue-green color.
Learn more:About colored flame here:
https://brainly.com/question/6871204
#SPJ11
Colored flame is produced when an electron transitions from a higher energy state to a lower energy state within an atom or molecule.
When an electron absorbs energy, it gets excited and moves to a higher energy level or orbital. As the electron returns to its original energy level, it releases the excess energy in the form of light. The color of the emitted light depends on the specific energy difference between the levels involved in the transition.
Different elements and compounds exhibit characteristic flame colors due to the unique energy levels and electron configurations they possess. For example, burning copper compounds produce a blue-green flame, while potassium compounds produce a violet flame. The presence of specific metal ions or compounds in a flame can give rise to distinct colors.
By introducing substances or compounds into a flame, such as metal salts, the electrons in the atoms of those substances can absorb energy from the heat of the flame and undergo excitation. When these excited electrons return to their ground state, they release energy in the form of light, resulting in the observed colored flame.
To know more about electron,
https://brainly.com/question/12001116#
#SPJ11
Water flows at 50 ft/s through a pipe with diameter of 2 inches. This same pipe goes down to the basement of the building, 25 ft lower, and the pressure remains unchanged. What is the diameter of the pipe in the basement? a. 1 in b. 1 in c. 1 in d. 2 in e. 2 in
The diameter of the pipe in the basement is 2.04 inches.
The diameter of the pipe at the top is 2 inches, and the water flows at 50 ft/s.
The pipe goes down to the basement of the building, 25 ft lower, and the pressure remains unchanged.
We have to determine the diameter of the pipe in the basement.
According to Bernoulli's principle, the total pressure in a fluid is the sum of the static pressure (p), dynamic pressure (1/2ρv²), and potential energy (ρgh).
Here, the static pressure and potential energy remain constant.
Thus, the total pressure is equal to the dynamic pressure.
p + ρgh + 1/2ρv1² = p + ρgh + 1/2ρv2²
Pressure at the top = Pressure at the bottomρgh + 1/2ρv1² = 1/2ρv2²
Since the density of water is constant, we can ignore it.
Therefore,ρgh + 1/2v1² = 1/2v2²...[1]v1 = 50 ft/s, h = 25 ftv2 = sqrt(2 × (ρgh + 1/2v1²))...[2]
Let's substitute the given values in [2].v2 = sqrt(2 × (32.2 × 25 + 1/2 × (50)²))v2 = 61.8 ft/s
The continuity equation states that the mass flow rate of fluid is constant along the pipe.
ρ₁A₁v₁ = ρ₂A₂v₂ρ₁A₁v₁ = ρ₂A₂v₂....[3]A₁ = πd₁²/4,
A₂ = πd₂²/4, ρ₁ = ρ₂ = ρ (density of water)
Thus, we have
ρA₁v₁ = ρA₂v₂ρd₁²v₁ = d₂²v₂...(from [3])d₁²v₁ = d₂²v₂
Let's substitute the given values in the above equation2² × 50 = d₂² × 61.8d₂² = 4 × 50/61.8d₂ = 2.04 inches (approx.)
Therefore, the diameter of the pipe in the basement is 2.04 inches. Hence, the correct answer is option (e) 2 in.
Learn more about potential energy
brainly.com/question/24284560
#SPJ11
An ac generator has a Vp of 100 V. What is the angle for the instantaneous voltage to be 92 V? O 75 degrees 45 degrees 67 degrees 15 degrees
Photovoltaic (PV) technology is best described as Select one: a. passive solar technology b. trapping sun's heat and storing it for many varied uses c. using sunlight to generate electricity through p
Photovoltaic (PV) technology is best described as using sunlight to generate electricity through photovoltaic panels. It is an active solar technology that transforms solar energy into electricity. Photovoltaic technology has become increasingly popular as an alternative energy source due to its low carbon footprint,
high efficiency, and versatility.Photovoltaic technology is built on the phenomenon of the photovoltaic effect, which occurs when a photovoltaic cell absorbs photons from the sun and releases electrons. These electrons are then used to create an electric current that can be harnessed as electricity.
Photovoltaic technology works best in sunny areas, but it is also capable of producing electricity on cloudy days. The technology is very flexible, with the ability to be utilized in a variety of applications ranging from powering small electronic devices like calculators and watches to powering entire homes and businesses. Additionally, the technology is continually evolving and improving, making it even more effective and affordable. As a result, photovoltaic technology is expected to become a significant player in the energy sector in the years to come.
To know more about technology visit:
https://brainly.com/question/9171028
#SPJ11
The position of a dragonfly that is flying parallel to the ground is given as a At what value of t does the velocity vector of the insect make an angle of 40.0 ∘
clockwise from the x-axis? function of time by r
=[2.90 m+(0.0900 m/s 2
)t 2
] i
^
− Express your answer with the appropriate units. (0.0150 m/s 3
)t 3
j
^
. Part B At the time calculated in part (a), what is the magnitude of the acceleration vector of the insect? Express your answer with the appropriate units. Part C At the time calculated in part (a), what is the direction of the acceleration vector of the insect? Express your answer in degrees.
Part A: At approximately t = -1.39 s, the velocity vector of the insect makes an angle of 40.0° clockwise from the x-axis. Part B: At this time, the magnitude of the acceleration vector is approximately 0.271 m/s², and Part C: its direction is approximately 21.8°.
Part A: To find the value of t when the velocity vector of the insect makes an angle of 40.0° clockwise from the x-axis, we need to determine the x and y components of the velocity vector and then calculate the angle.
The velocity vector of the insect is given as v = (0.0900 m/s² * t²) i + (0.0150 m/s³ * t³) j.
The x-component of the velocity is v_x = 0.0900 m/s² * t².
The y-component of the velocity is v_y = 0.0150 m/s³ * t³.
To calculate the angle, we can use the arctan function:
θ = arctan(v_y / v_x).
Substituting the values, we have:
θ = arctan((0.0150 m/s³ * t³) / (0.0900 m/s² * t²)).
Simplifying, we get:
θ = arctan(0.0150 t).
We want to find the value of t when θ is 40.0° clockwise, so we set θ equal to -40.0°:
-40.0° = arctan(0.0150 t).
To solve for t, we take the tangent of both sides:
tan(-40.0°) = 0.0150 t.
Now we can solve for t:
t = tan(-40.0°) / 0.0150.
Using a calculator, we find:
t ≈ -1.39 s (rounded to two decimal places).
Therefore, at t ≈ -1.39 s, the velocity vector of the insect makes an angle of 40.0° clockwise from the x-axis.
Part B: To find the magnitude of the acceleration vector at the calculated time, we need to differentiate the velocity vector with respect to time.
The acceleration vector is given by a = dv/dt.
Differentiating the velocity vector with respect to time, we get:
a = (d/dt)(0.0900 m/s² * t²) i + (d/dt)(0.0150 m/s³ * t³) j.
Taking the derivatives, we have:
a = (0.1800 m/s² * t) i + (0.0450 m/s³ * t²) j.
At t ≈ -1.39 s, we can substitute the value of t into the expression for a:
a = (0.1800 m/s² * (-1.39 s)) i + (0.0450 m/s³ * (-1.39 s)²) j.
Calculating the values, we find:
a ≈ (-0.2502 m/s²) i + (-0.1003 m/s²) j.
The magnitude of the acceleration vector is given by:
|a| = √((-0.2502 m/s²)² + (-0.1003 m/s²)²).
Calculating the magnitude, we find:
|a| ≈ 0.271 m/s² (rounded to three decimal places).
Therefore, at the calculated time, the magnitude of the acceleration vector of the insect is approximately 0.271 m/s².
Part C: To find the direction of the acceleration vector at the calculated time, we can calculate the angle it makes with the positive x-axis.
The angle θ can be found using the arctan function:
θ = arctan(a_y / a_x).
Substituting the values, we have:
θ = arctan((-0.1003 m/s²) / (-0.2502 m/s²)).
Simplifying, we get:
θ = arctan(0.400).
Using a calculator, we find:
θ ≈ 21.8°.
Therefore, at the calculated time, the direction of the acceleration vector of the insect is approximately 21.8°.
To know more about acceleration vector, refer to the link below:
https://brainly.com/question/33520497#
#SPJ11
how many orbitals are in the third principal energy level?
The number of orbitals in the third principal energy level is 18.
In the Bohr model of the atom, electrons are arranged in energy levels or shells. The number of orbitals in an energy level can be determined using the formula 2n^2, where n is the principal quantum number. The principal quantum number represents the energy level or shell.
In this case, we are looking for the number of orbitals in the third principal energy level. So, we can substitute n = 3 into the formula:
Number of orbitals = 2(3)^2 = 2(9) = 18.
Learn more:About orbitals here:
https://brainly.com/question/18914648
#SPJ11
The third principal energy level (n=3) contains a total of 9 orbitals. These orbitals are divided into three sublevels: 3s (1 orbital), 3p (3 orbitals), and 3d (5 orbitals). The 3s orbital can hold up to 2 electrons, the 3p sublevel can accommodate up to 6 electrons, and the 3d sublevel can hold up to 10 electrons.
The third principal energy level, also known as the n=3 shell, can contain a total of 9 orbitals. These orbitals are designated as 3s, 3p, and 3d orbitals.
The 3s orbital can hold a maximum of 2 electrons, the 3p orbitals can collectively hold a maximum of 6 electrons (with each individual 3p orbital holding 2 electrons), and the 3d orbitals can collectively hold a maximum of 10 electrons (with each individual 3d orbital holding 2 electrons). However, in the case of the third energy level, only the 3s and 3p orbitals are present.
Thus, the third principal energy level consists of 3s and 3p orbitals, resulting in a total of 9 orbitals.
To know more about orbitals refer here
https://brainly.com/question/32355752#
#SPJ11
Force acting between two argons are well approximated by the LennardJones potential given by U(r)=
r
12
a
−
r
6
b
. Find the equilibrium separation distance between the argons.
The Lennard-Jones potential for the force acting between two argons is given by:U(r)= (a/r)^12 - (b/r)^6where, r is the distance between the two argon atoms and a and b are constants.The equilibrium separation distance between the argons is given by the minimum value of U(r). Thus, we differentiate U(r) with respect to r and equate it to zero to find the minimum value.U'(r) = -12a^12/r^13 + 6b^6/r^7At the minimum value, U'(r) = 0⇒ -12a^12/r^13 + 6b^6/r^7 = 0⇒ 2(a/r)^12 = (b/r)^6⇒ (a/r)^6 = b^3/r^6⇒ r = (b/a)^(1/6)Thus, the equilibrium separation distance between the argons is given by r = (b/a)^(1/6).Answer: The equilibrium separation distance between the argons is given by r = (b/a)^(1/6).
The equilibrium separation distance between the argon is given by r = (b/a)^(1/6).
The Lennard-Jones potential for the force acting between two argon is given by: U(r)= (a/r)^12 - (b/r)^6, where r is the distance between the two argon atoms and a and b are constants.
The equilibrium separation distance between the argon is given by the minimum value of U(r).
Thus, we differentiate U(r) with respect to r and equate it to zero to find the minimum value: U'(r) = -12a^12/r^13 + 6b^6/r^7
At the minimum value, U'(r) = 0⇒ -12a^12/r^13 + 6b^6/r^7 = 0⇒ 2(a/r)^12 = (b/r)^6⇒ (a/r)^6 = b^3/r^6⇒ r = (b/a)^(1/6)
Thus, the equilibrium separation distance between the argon is given by r = (b/a)^(1/6).
To know more about force refer to:
https://brainly.com/question/25239010
#SPJ11
3. QUESTION 3 A 60 TEETH B 30 TEETH DRIVEN (LOAD) DRIVER (EFFORT) 3.1. Calculate the velocity ratio in the given gear system. 3.2. Calculate the force ratio in the given gear system
1. The velocity ratio in the given gear system is 2
2. The force ratio in the given gear system is 0.5
1. How do i determine the velocity ratio?The velocity ratio in the given gear system can be obtained as illustrated below:
Number of driven gear = 60 teethNumber of driver's gear = 30 teethVelocity ratio =?Velocity ratio = Number of driven gear / Number of driver's gear
= 60 / 30
= 2
Thus, the velocity ratio is 2
2. How do i determine the force ratio?The force ratio in the given gear system can be obtained as follow:
Velocity ratio = 2Force ratio =?Force ratio = 1 / velocity ratio
= 1 / 2
= 0.5
Thus, the force ratio is 0.5
Learn more about gear ratio:
https://brainly.com/question/14339779
#SPJ1
Can you please explain in detail an experiment that Ampere
performed using Amperes Law and what happened. Thankyou
Ampere concluded that the force between the wires was the result of the interaction between the magnetic fields of the two wires. Ampere's discovery was essential as it helped in explaining how electric currents generate a magnetic field. The concept of electromagnetism laid the foundation for the modern world's electrical and electronic applications.
Yes, I would be happy to explain an experiment that Ampere performed using Ampere's Law. Ampere is recognized for his contribution to the field of electromagnetism. The laws he discovered have laid the foundation for modern electrical and electronic applications. One of the significant discoveries of Ampere was Ampere's Law.Ampere's law helps in finding out the magnetic field created by a current-carrying conductor. It states that the magnetic field in the closed loop is equal to the sum of the magnetic field of the current-carrying conductor that passes through it. Mathematically, it is represented is the differential length of the path of the loop, and the permeability of free space. An experiment that Ampere performed using Ampere's Law:According to the biographical notes of Andre Marie Ampere by G.W.C. Kaye, "Ampere demonstrated his theory of magnetism by means of an experiment in which two parallel wires were placed at a certain distance from each other, and a current passed through them in the same direction." He noticed that the wires were attracted towards each other. When the direction of current flow was reversed, the wires were repelled. The force between the two wires was proportional to the current passing through the wires. Ampere concluded that the force between the wires was the result of the interaction between the magnetic fields of the two wires. Ampere's discovery was essential as it helped in explaining how electric currents generate a magnetic field. The concept of electromagnetism laid the foundation for the modern world's electrical and electronic applications.
To know more about electromagnetism visit:
https://brainly.com/question/31038220
#SPJ11
An AM signal has a carrier frequency of 3MHz and an amplitude of 5V peak. It is modulated by a sine wave with a frequency of 500Hz and a peak voltage of 2V. Write the equation for the signal. A) V(t)-[3+5sin(5.18 t)]sin(17.56 t) B no answer V(t)=[10+5sin(3.2 t)]sin(18.34 t) D) V(t)=[5+2sin(3.14 t)]sin(18.85 t) E) V(t)=[2+10sin(8.14 t)]sin(16.85 t)
The equation for the signal modulated by a sine wave with a frequency of 500Hz and a peak voltage of 2V, given that an AM signal has a carrier frequency of 3MHz and an amplitude of 5V peak is: V(t) = [5 + 2sin(2π(500)t)]sin(2π(3 × 10^6)t). Therefore, option D) V(t)=[5+2sin(3.14 t)]sin(18.85 t) is the correct answer.
The formula used to derive the equation is:V(t) = [Ac + Am sin(2πfmt)] sin(2πfct)
Where,V(t) is the voltage of the modulated signal.
Am is the amplitude of the modulating signal,fmt is the frequency of the modulating signal,
fct is the frequency of the carrier signal.
Ac is the amplitude of the carrier signal.
Applying these to the given values, we get,
V(t) = [5 + 2sin(2π(500)t)]sin(2π(3 × 10^6)t)
= [5+2sin(3.14t)]sin(18.85t)
Therefore, option D is correct.
To learn more about frequency visit;
https://brainly.com/question/29739263
#SPJ11
Two carts mounted on an air track are moving toward one another. Cart 1has a speed of 1.1 m/s and a mass of 0.42 kg. Cart 2 has a mass of 0.71 kg. (a) If the total momentum of the system is to be zero, what is the initial speed (in m/s ) of Cart 2? (Enter a number.) m/s (b) Does it follow that the kinetic energy of the system is also zero since the momentum of the system is zero? Yes No (c) Determine the system's kinetic energy (in J) in order to substantiate your answer to part (b). (Enter a number.) J
a) initial speed of Cart 2 is approximately 0.651 m/s.
b) No, it does not follow that the kinetic energy of the system is also zero
c) system's kinetic energy is approximately 0.483 J.
(a) For initial speed of Cart 2, we can use the principle of conservation of momentum. The total momentum before the collision is equal to the total momentum after the collision. Since the total momentum of the system is to be zero,
The momentum of an object is calculated by multiplying its mass by its velocity. So, we have:
Momentum of Cart 1 = Mass of Cart 1 * Velocity of Cart 1
Momentum of Cart 2 = Mass of Cart 2 * Velocity of Cart 2
Since the total momentum of the system is zero, we can set up the following equation:
0 = (0.42 kg * 1.1 m/s) + (0.71 kg * Velocity of Cart 2)
Solving for the velocity of Cart 2:
0 = 0.462 kg*m/s + (0.71 kg * Velocity of Cart 2)
-0.462 kg*m/s = 0.71 kg * Velocity of Cart 2
Velocity of Cart 2 = -0.462 kg*m/s / 0.71 kg
Velocity of Cart 2 ≈ -0.651 m/s
Therefore, the initial speed of Cart 2 is approximately 0.651 m/s.
(b) No, it does not follow that the kinetic energy of the system is also zero just because the momentum of the system is zero. Kinetic energy depends on the mass and velocity of an object, while momentum only considers the mass and velocity. Therefore, the kinetic energy can still be non-zero even if the momentum is zero.
(c) For system's kinetic energy, we can calculate the individual kinetic energies of Cart 1 and Cart 2, and then sum them up. The kinetic energy (KE) of an object is given by the formula:
KE = (1/2) * Mass * Velocity^2
The kinetic energy of Cart 1 is:
KE1 = (1/2) * 0.42 kg * (1.1 m/s)^2
The kinetic energy of Cart 2 is:
KE2 = (1/2) * 0.71 kg * (-0.651 m/s)^2
To find the total kinetic energy of the system, we add the individual kinetic energies together:
Total kinetic energy = KE1 + KE2
Total kinetic energy = 0.332 J + 0.151 J
Total kinetic energy = 0.483 J
Therefore, the system's kinetic energy is approximately 0.483 J.
To learn more about kinetic energy and Momentum :
https://brainly.com/question/12880315
#SPJ11
It is difficult to extinguish a fire on a crude oil tanker, which is quite dangerous, because each liter of crude oil releases 2.80×107 J of energy when burned. To show this difficulty in a safer setting, calculate the number of liters of water that must be expended to absorb the energy released by burning 1.00 L of crude oil, if the water has its temperature raised from 21.5 °C to 100 °C , it boils, and the resulting steam is raised to 285 °C. Use 4186 J/(kg·°C) for the specific heat of water and 2020 J/(kg·°C) for the specific heat of steam.
The number of liters of water that must be expended to absorb the energy released by burning 1.00 L of crude oil is 224.7 liters of water. Mass of water required to absorb the energy released by burning 1.00 L of crude oil is given by the expression: M = c water × m × ΔT₁ + L × m + c steam × m × ΔT₂
Density of steam, ρsteam = 0.6 kg/m³. Latent heat of vaporization, L = 2.26 × 10⁶ J/kg.
Let the number of liters of water required be n. The mass of water required to absorb the energy released by burning 1.00 L of crude oil is given by the expression:
M = c water × m × ΔT₁ + L × m + c steam × m × ΔT₂
where, ΔT₁ = T₁ - T0
= 100 - 21.5
= 78.5 °C,
ΔT₂ = T₂ - T₁
= 285 - 100
= 185 °C,
T₀ = 21.5 °C,
T₁ = 100 °C, and
T₂ = 285 °C.
Solving the above expression for m: 2.80 × 107 = 4186 × m × 78.5 + 2.26 × 106 × m + 2020 × m × 185
= 328081 m + 5096 m + 374300 m
= 707477 mm
= 2.247 × 10⁵ kg
≈ 224.7 kg
n = m/ρwater
= 224.7/1000
= 0.2247 m³
= 224.7 L
Therefore, the number of liters of water that must be expended to absorb the energy released by burning 1.00 L of crude oil is 224.7 liters of water.
To know more about energy, refer
https://brainly.com/question/13881533
#SPJ11
Calculate the amount of heat energy required to increase the temperature of 4.2 moles of carbon dioxide, which is a polyatomic gas, from 300K to 400K while maintaining a pressure of 74000 kPa. a. 7000 J O b. 8700 J O c. 1.4e4J O d. 1.0e4J 52001
The amount of heat energy required to increase the temperature of 4.2 moles of carbon dioxide, which is a polyatomic gas, from 300K to 400K while maintaining a pressure of 74000 kPa is 1.4e4J. The answer is option C.1.4e4J.
Explanation:Given dataNumber of moles of carbon dioxide, n = 4.2 molesInitial temperature, T₁ = 300 KFinal temperature,
T₂ = 400 KPressure,
P = 74000 kPa
Gas constant, R = 8.314 JK⁻¹mol⁻¹
Formula used for calculating heat energyΔH = nCpΔTwhere,Cp is the specific heat capacity of the gas at constant pressureΔT is the temperature change
We know that Cp = (7/2)R for polyatomic gases like carbon dioxide. Substituting the given values in the formula, we get
ΔH = nCpΔT
ΔH = 4.2 × (7/2) × 8.314 × (400 - 300)
ΔH = 1.4 × 10⁴ J
Therefore, the amount of heat energy required to increase the temperature of 4.2 moles of carbon dioxide, which is a polyatomic gas, from 300K to 400K while maintaining a pressure of 74000 kPa is 1.4e4J. The answer is option C.1.4e4J.
To know more about heat energy, visit:
https://brainly.com/question/20038450
#SPJ11
A pulley 180 mm diameter rotating at 1440 rpm drives a fan by means of a vee belt. The angle of contact of the belt on the pulley is 160°. The tight-side belt tension is 1200 N and the coefficient of friction of the contact surfaces is 0.4. The half groove angle is 24º. Calculate: a) the power transmitted. b) the rotational speed of the driven pulley if the driven pulley has a diameter of 900 mm. 10 marks]
The rotational speed of the driven pulley is 2744 rpm
a) The power transmitted
The power transmitted is the product of the tension force, the velocity of the belt, and the coefficient of power. It is expressed in watts. Given that the diameter of the pulley is 180mm, its radius will be given as:
Radius = Diameter / 2 = 180 / 2 = 90mm
The angular velocity of the pulley is given as:ω = (2πN) / 60 = (2 × 22/7 × 1440) / 60 = 301.6 rad/s
The linear velocity of the pulley can be found as:V = ωr = 301.6 × 0.09 = 27.144 m/s
The power transmitted can be calculated as: P = T1 × V × Coefficient of power
Where T1 = 1200N (tight side tension), and coefficient of power = 0.4
Thus,P = 1200 × 27.144 × 0.4 = 13058.88 W = 13.0588 kW
b) The rotational speed of the driven pulley
The speed of the driven pulley can be calculated by equating the linear velocity of the belt on the two pulleys.
Given that the diameter of the driven pulley is 900 mm, its radius will be given as:
Radius = Diameter / 2 = 900 / 2 = 450 mm
The linear velocity of the belt is given as :V = ωR Where R is the radius of the driven pulley
Thus,1440 × (2π/60) × 0.09 = N × (2π/60) × 0.45
N = 1440 × 0.09 / 0.45 = 288 rad/s or 2744 rpm
Therefore, the rotational speed of the driven pulley is 2744 rpm
Learn more about rotational speed from the given link
https://brainly.com/question/31261267
#SPJ11
Using the psychrometric relations solve this question: The dry- and wet-bulb temperatures of atmospheric air at 105 kPa are 26 and 12°C, respectively. Determine: (a) the specific humidity, (b) the relative humidity, and (c) the enthalpy of the air, in kJ/kg dry air.
Using the psychrometric relations to solve the given problemThe values of dry-bulb temperature (DBT) and wet-bulb temperature (WBT) of atmospheric air are provided as DBT = 26 °C and WBT = 12 °C at 105 kPa.To determine(a) . The enthalpy of the air is 58.94 kJ/kg of dry air.
The specific humidityLet's use the relation of the specific humidity with dry-bulb temperature, wet-bulb temperature, and atmospheric pressure, which is given as:W = (622Pw)/(P-Pw), where W is the specific humidity, Pw is the vapor pressure, and P is the atmospheric pressure.622 is the ratio of the molar mass of water vapor to dry air. At saturation, the vapor pressure is maximum, i.e., the air is saturated, and the relative humidity is 100%.
Therefore, the relative humidity is 77.73%.(c) The enthalpy of the air Enthalpy is the total energy of the air per unit mass, including its internal energy and the energy due to its motion.Let's use the relation of enthalpy with specific humidity and dry-bulb temperature, which is given as:h = 1.005(DBT) + W(2501+1.84DBT), where h is the enthalpy of the air in kJ/kg of dry air.Putting the given values, we get:h = 1.005(26) + 0.0199(2501+1.84*26)h = 58.94 kJ/kg of dry air
To know more about psychrometric visit:
https://brainly.com/question/30452622
#SPJ11
A 20 MHz uniform plane wave travels in a lossless material with the following characteristics:
u_r = 3 , ε_r = 3
Calculate (remember to include units):
a) (3%) The phase constant of the wave.
b) (3%) The wavelength.
c) (3%) The speed of propagation of the wave.
d) (3%) The intrinsic impedance of the medium.
e) (4%) The average power of the Poynting vectorr or Irradiance, if the amplitude of the electric field Emax = 100 V/m.
d) (4%) If the wave reaches an RF field detector with a square area of 1 cm 1 cm, how much power in Watts would be read on the screen?
A 20 MHz uniform plane wave travels in a lossless material with the following characteristics:
a) Calculation of the phase constant of the wave:
The phase constant is expressed as β=ω√(μɛ)
[tex]=2πf√(μɛ)[/tex]
[tex]=2π(20x10^6)√(3*3)[/tex]
=69.282 rad/meter
b) Calculation of the wavelength of the wave:
[tex]λ=2π/β[/tex]
[tex]=2π/69.282[/tex]
=0.0907 m
c) Calculation of the speed of propagation of the wave:
[tex]c=1/√(μɛ)[/tex]
[tex]=1/√(3*3)[/tex]
=1/3 m/s
d) Calculation of the intrinsic impedance of the medium:
[tex]η=√(μ/ɛ)[/tex]
[tex]=√3[/tex]
=1.732 Ohms.
e) Calculation of the average power of the Poynting vector or Irradiance:
From the given information, the amplitude of the electric field Emax = 100 V/m. Thus,
[tex]E_rms=E_max/√2[/tex]
[tex]= 100/√2 V/m[/tex] Irradiance (Poynting Vector) is given by the formula:
[tex]I=1/2cE_rms^2[/tex]
[tex]I=1/2(1/3)(100/√2)^2[/tex]
[tex]I=3.333 Watts/m^2[/tex]
d) If the wave reaches an RF field detector with a square area of 1 cm 1 cm, then the power in Watts would be read on the screen will be:
[tex]P=I*A[/tex]
[tex]=I*(l^2).[/tex]
To know more about uniform visit:
https://brainly.com/question/12920060
#SPJ11
What is the velocity \( v \) of the box 2 seconds later? \[ v= \]
The velocity of the box 2 seconds later is 10 m/s.
We can find the velocity of the box 2 seconds later using the given acceleration and initial velocity of the box.
We use the following kinematic equation to solve for the velocity:\[v = u + at\]where v is the final velocity, u is the initial velocity, a is the acceleration, and t is the time taken.
We are given that the box starts from rest and experiences an acceleration of 5 m/s². Thus, the initial velocity of the box is u = 0 m/s, and the acceleration is a = 5 m/s².
The time taken is t = 2 s.
Substituting these values in the above equation,\[v = u + at\] \[v = 0 + 5 \times 2\] \[v = 10 m/s\]
Therefore, the velocity of the box 2 seconds later is 10 m/s.
To learn more about acceleration visit;
https://brainly.com/question/2303856
#SPJ11