Code has mentioned the minimum requirement of 2.44 m for each run of conduit.∴ Number of Expansion Joints required = ΔL / 2.44 m≈ 1.05 / 2.44≈ 0.43≈ 1 Expansion Joint (required)
Given data: Length of the conduit = 115 m Trade size of the conduit = 91 mm Temperature range = -35°C to 40°C
Formula used: ΔL = αLΔT
Where, ΔL = Change in length α = Coefficient of linear expansion L = Original length ΔT = Change in temperature Coefficient of linear expansion (α) for Rigid Steel is 12.10 × 10⁶ /°C
Change in temperature (ΔT) = (40 - (-35))°C = 75°C
Total change in length,ΔL = αLΔTΔL = (12.10 × 10⁶ /°C) × (115 m) × (75°C)ΔL = 1.05 m
Thus, the change in length of 115 m run of 91 mm or 3% trade size Rigid Steel conduit in a temperature range of -35°C to 40°C is 1.05 m.
Yes, the expansion joint is required.
Code has mentioned the minimum requirement of 2.44 m for each run of conduit.∴ Number of Expansion Joints required = ΔL / 2.44 m≈ 1.05 / 2.44≈ 0.43≈ 1 Expansion Joint (required)
To know more about Expansion Joints refer to:
https://brainly.com/question/30117128
#SPJ11
Consider having two Full-Am signals: an AM signal with high
modulation index and another AM signal with low modulation index.
Which of them has higher power efficiency?
The AM signal with low modulation index has higher power efficiency.
In amplitude modulation (AM), the modulation index represents the extent of variation in the carrier signal's amplitude caused by the modulating signal. It is defined as the ratio of the peak amplitude of the modulating signal to the peak amplitude of the carrier signal. A high modulation index means that the modulating signal causes significant variation in the carrier signal's amplitude, while a low modulation index indicates minimal variation.
The power efficiency of an AM signal is determined by how effectively it utilizes power to transmit information. In the case of AM, power efficiency refers to the ratio of the power carried by the modulating signal (information) to the total power consumed by the transmitted signal.
An AM signal with a high modulation index requires a larger power allocation to accommodate the wide amplitude variations caused by the modulating signal. This results in a higher total power consumption for the transmitted signal. Conversely, an AM signal with a low modulation index requires less power to represent the modulating signal since it causes minimal amplitude variations in the carrier signal. As a result, the AM signal with a low modulation index has higher power efficiency compared to the one with a high modulation index.
In summary, the AM signal with low modulation index has higher power efficiency because it requires less power to represent the modulating signal, resulting in lower total power consumption for the transmitted signal.
Learn more about power efficiency
brainly.com/question/31283944
#SPJ11
Multiply two numbers, x and y, without using MUL instruction. Use registers $t1 and $t2 for inputs and register $t3 to store the result.
The values of x, y, and the result are stored in memory locations x, y, and result, respectively. You may need to modify the code accordingly if the values are stored differently.
To multiply two numbers, x and y, without using the MUL instruction in MIPS assembly language, you can use a loop to perform repeated addition. Here's an example code snippet that demonstrates this:
```assembly
.data
x: .word 5
y: .word 7
result: .word 0
.text
.globl main
main:
# Load x and y from memory into registers $t1 and $t2
lw $t1, x
lw $t2, y
# Initialize the result to 0
li $t3, 0
# Loop to perform repeated addition
loop:
add $t3, $t3, $t1 # Add x to the result
addi $t2, $t2, -1 # Decrement y by 1
# Check if y is zero
beqz $t2, done
# Continue looping
j loop
done:
# Store the result in memory
sw $t3, result
# Exit the program
li $v0, 10
syscall
```
In this code, the values of x and y are loaded from memory into registers $t1 and $t2, respectively. The result is initialized to 0 in register $t3.
The loop starts by adding the value of x to the result ($t3) and then decrementing the value of y by 1. If y is not zero, the loop continues, and the addition is performed again. Once y becomes zero, the loop ends, and the result is stored in memory.
After executing this code, the value of the product of x and y will be stored in the memory location specified by the result label.
Learn more about memory locations here
https://brainly.com/question/33357090
#SPJ11
Give the definitions of the terms below and give a practical example for each case:
1.Exposed conductive parts
2.Exposed conductive parts
3.Compatibility
4.Conservability
5.Heterochronism
The definitions of the terms below and give a practical example for each case are as follows-
1. Exposed conductive parts: Exposed conductive parts refer to parts of an electrical system that are conductive and can be touched or touched accidentally by people. Such parts should be well insulated to prevent electric shocks or electrocution. A good example is a metal case of an electrical appliance that can be touched by a person when the appliance is plugged in, and it has a defect.
2. Insulation: Insulation refers to a material that is used to cover conductive parts of an electrical system to protect people from electric shocks and also protect the conductive parts from coming into contact with other conductive materials. A practical example is using a plastic material to cover a cable or wire that is carrying electricity to prevent a person from touching it.
3. Compatibility: Compatibility refers to the ability of an electrical system to work together seamlessly without any issues or incompatibilities. A good example is a battery charger that is compatible with the device being charged, ensuring that it charges the battery as expected.
4. Conservability: Conservability refers to the ability of an electrical system to conserve energy. A practical example is the use of energy-saving bulbs that use less energy than traditional bulbs, ensuring that energy is conserved.
5. Heterochronism: Heterochronism refers to the occurrence of a particular event at different times in different organisms. A practical example is the blooming of flowers, where different flowers may bloom at different times in different locations based on the environment and climate.
know more about Insulation
https://brainly.com/question/14363642
#SPJ11
The following are the specifications of a C-Band GEO satellite
link budget in clear air conditions. The calculation of the CNR in
a satellite link is based on two equations of received signal power
an
The following are the specifications of a C-Band GEO satellite link budget in clear air conditions. The calculation of the CNR in a satellite link is based on two equations of received signal power an
The specifications of a C-Band GEO satellite link budget in clear air conditions are as follows.
1. The transmit power of the satellite is 55 dBW.
2. The gain of the satellite antenna is 38 dB.
3. The cable loss between the satellite and the ground station is 1 dB.
4. The receive antenna gain is 44 dB.
5. The noise temperature of the satellite is 125 K.
To know more about specifications visit:
https://brainly.com/question/32619443
#SPJ11
Q5. The following digital filter is given H(2) 11.62 ¹+0.642- = 1-1.82-1+0.812-2 The filter coefficients are quantized to 5 bits in fixed point where the binary representation is sign magnitude of the form, XXX.XX (b; b4 b; .b2 bi), with the most significant bit being the sign. The fixed point numerical representation here is of the form b5 (sign bit), b4 x 2¹ + b3 x 2⁰ + b2 x 2-¹ + b1 x 2-² a) Write the quantized frequency response function. H(z) 2° -(2° +2¹)₂+(2¯¹ +2¯²)₂²² 20-(2° +2¹+2²)z +(2¹ +2²)a 1-1.52 +0.75z-2 = 1-1.752¹ +0.75z²
The quantized frequency response function of the given digital filter is H(z) = 2° - (2° + 2¹)z + (2¯¹ + 2¯²)z²² / (20 - (2° + 2¹ + 2²)z + (2¹ + 2²)z²).
In digital signal processing, the frequency response function of a filter describes how the filter affects different frequencies of a signal. It indicates how the filter amplifies or attenuates each frequency component. In this case, the given filter coefficients have been quantized to 5 bits in fixed-point representation.
Quantization involves representing real numbers with a limited number of bits, which introduces quantization errors. The quantized frequency response function H(z) represents the response of the filter with quantized coefficients. The numerator and denominator of H(z) are polynomials in z, where z represents the complex frequency variable.
The quantized coefficients affect the frequency response of the filter.The quantization errors can introduce distortions and affect the filter's performance. By quantizing the coefficients to 5 bits, the accuracy of the filter is reduced compared to using higher precision coefficients.
quantized frequency response functions and the impact of quantization on digital filters to gain a deeper understanding of the challenges and considerations in implementing filters with limited precision coefficients. #SPJ11
Approximate the value of sum after the following code fragment, in terms of variable n in Big-Oh notation. (2 pts) [2.1] Please answer the estimated run time of the following program segment in Big-Oh notation. int sum = 0; for (int i = 1; i <= n - 3; i++) { for (int j = 1; j <= n + 4; j += 5) { sum += 2; } sum++; } for (int i = 1; i <= 100; i++) { sum++; } [2.2] Please answer the estimated run time of the following program segment in Big-Oh notation. int sum = 0; for (int i = 1; i <= n; i++) { sum++; } for (int j = 1; j <= n / 2; j++) { sum++; }
The estimated run time of the given program segments in Big-Oh notation are:T(n) = O(n^2) and T(n) = O(n)
Given the program segment: int sum = 0; for (int i = 1; i <= n - 3; i++) { for (int j = 1; j <= n + 4; j += 5) { sum += 2; } sum++; } for (int i = 1; i <= 100; i++) { sum++; }Here, the first two loops have O(n) time complexity and the last loop has a constant time complexity of O(1)The total time complexity of the given program segment can be obtained as:T(n) = O(n^2) + O(1) + O(1) = O(n^2)
Therefore, the estimated run time of the given program segment in Big-Oh notation is O(n^2)2.2)Given the program segment: int sum = 0; for (int i = 1; i <= n; i++) { sum++; } for (int j = 1; j <= n / 2; j++) { sum++; }Here, the first loop has a time complexity of O(n) and the second loop has a time complexity of O(n) / 2 i.e., O(n).Therefore, the estimated run time of the given program segment in Big-Oh notation is O(n).Hence, the estimated run time of the given program segments in Big-Oh notation are:T(n) = O(n^2) and T(n) = O(n)
To know more about program refer to
https://brainly.com/question/14368396
#SPJ11
7 Suggest sensors that could be used with control systems to give measures of (a) the temperature of a liquid, (b) whether a workpiece is on the work table, (c) the varying thickness of a sheet of met
Sensors are devices used to detect changes in the physical environment such as temperature, pressure, and light and translate these changes into electrical signals that can be read by a control system.
Seven sensors that can be used with control systems to give measures of temperature, workpiece presence and varying thickness of a sheet of met are discussed below:(a) Temperature sensors: These sensors are used to measure the temperature of liquids and can be of different types.
They include RTDs, thermistors, thermocouples, and infrared sensors.(b) Presence sensors: These sensors detect whether a workpiece is on the work table. They can be inductive, capacitive, optical or magnetic sensors depending on the type of workpiece.(c) Thickness sensors: These sensors measure the varying thickness of a sheet of metal. They can be based on ultrasonic, eddy current, laser or radiation principles.
To know more about sensors visit:
https://brainly.com/question/33219578
#SPJ11
Determine the Fourier Transform of the signals a) x(n) = u(n+4)−2(3)^ u(-n−1)
The Fourier transform of the given signal x(n) is given by [tex]Y(ω) = e^(-j4ω)/[1-e^(-jω)] - 2/(1-e^(jω)) [1/(1-3e^(-jω))][/tex] is the answer.
The Fourier transform of the signals is given by; [tex]Y(ω) = ∑_(n=∞)^∞▒〖x(n)e^(-jωn) 〗 ………… (1) where, x(n) = u(n+4)−2(3)^ u(-n−1) ……(2)[/tex]
The given signal x(n) can be written as a sum of two functions;[tex]x(n) = u(n+4) - 2u(-n-1) 3^n[/tex]
Therefore, equation (2) can be rewritten as[tex]x(n) = u(n+4) - 2u(-n-1) 3^n[/tex]
Hence, the Fourier Transform Y(ω) of x(n) is given by [tex]Y(ω) = ∑_(n=∞)^∞▒〖[u(n+4) - 2u(-n-1) 3^n] e^(-jωn) 〗[/tex]
Let us solve the above equation in parts; (a)
Fourier transform of u(n+4) using equation (1) is given by[tex]Y_1(ω) = ∑_(n=∞)^∞▒u(n+4) e^(-jωn) = e^(-j4ω) [1/(1-e^(-jω))] ……(3)(b)[/tex]
Fourier transform of u(-n-1) using equation (1) is given by[tex]Y_2(ω) = ∑_(n=∞)^∞▒u(-n-1) e^(-jωn) = 1/(1-e^(jω)) ……(4)(c)[/tex]
Fourier transform of 3^n using equation (1) is given by[tex]Y_3(ω) = ∑_(n=∞)^∞▒〖3^n e^(-jωn) 〗= 1/(1-3e^(-jω)) ……(5)[/tex]
Substituting equations (3), (4) and (5) in equation (2), we get; [tex]Y(ω) = e^(-j4ω)/[1-e^(-jω)] - 2/(1-e^(jω)) [1/(1-3e^(-jω))]Y(ω) = e^(-j4ω)/[1-e^(-jω)] - 2/(1-e^(jω)) [1/(1-3e^(-jω))][/tex]
Thus, the Fourier transform of the given signal x(n) is given by [tex]Y(ω) = e^(-j4ω)/[1-e^(-jω)] - 2/(1-e^(jω)) [1/(1-3e^(-jω))][/tex]
know more about Fourier transform
https://brainly.com/question/1542972
#SPJ11
It is required to implement a single-phase transformer
(120:240V) at 60Hz for a given power s=2,8kVA. The core is iron,
armored type and cooling by natural convection. Perform the
appropriate calculat
To implement a single-phase transformer (120:240V) at 60Hz for a given power s=2,8kVA with a core of iron, armored type, and cooling by natural convection, several calculations need to be done. Here are the steps to perform the calculations:1. Determine the voltage ratioV2 / V1 = N2 / N1where, V1 = primary voltage = 120VV2 = secondary voltage = 240V2. Calculate the current in the secondary windingIS = s / V2where, s = power = 2.8kVA3. Calculate the current in the primary windingIP = IS / awhere, a = transformation ratio = N1 / N2 = V2 / V1 (for ideal transformer)4. Determine the cross-sectional area of the core.A = s / (B * J)where, B = maximum flux density (tesla), J = current density (A/mm²)5. Calculate the number of turns in the secondary winding.N2 = V2 / 4.44 * f * Φmaxwhere, f = frequency = 60Hz, Φmax = maximum flux6. Determine the size of the wire based on the current densityJ = IS / A'where, A' = cross-sectional area of the wire7. Calculate the number of turns in the primary windingN1 = a * N2where, a = transformation ratio = V2 / V18. Determine the size of the wire based on the current densityJ' = IP / A''where, A'' = cross-sectional area of the wireThe calculations can be performed using these steps to implement a single-phase transformer (120:240V) at 60Hz for a given power s=2,8kVA with a core of iron, armored type, and cooling by natural convection.
Draw a complete single phase differential protection circuit diagram consisting a source, load, equipment under protection, two CBS, two CTS and blased differential relay (balanced beam relay) and show spill current, circulating current, external fault and Internal fault.
The spill current will be balanced in both coils, and no current will flow through the relay's trip coil under normal operating conditions.
The complete single phase differential protection circuit diagram consisting a source, load, equipment under protection, two CBS, two CTS and blased differential relay (balanced beam relay) and show spill current, circulating current, external fault and internal fault:
The balanced beam relay operates on the principle of spill current.
The primary current of each CT is linked to the relays' two coils (main and restraint) through a series circuit of a current transformer (CT), a current balance (CB), and a differential relay (R).
The spill current of the main CT, as well as the spill current of the backup CT, go through the main and restraint coils, respectively, of the differential relay. The spill current will be the same for the main and backup CTs since the primary currents are identical.
As a result, the spill current will be balanced in both coils, and no current will flow through the relay's trip coil under normal operating conditions.
To know more about spill current visit:
brainly.com/question/33223558
#SPJ11
How to design LQR Quadcopter in simulink.
To design LQR Quadcopter in simulink, we will require the following steps: Step 1: Mathematical model derivation To obtain the dynamic model of a Quadcopter.
Step 1: Mathematical Model Derivation There are four main components of the Quadcopter mathematical model, which are: Rotation angle equations of motion: The pitch angle (ϕ), the roll angle (θ), and the yaw angle (ψ) are the rotation angles of the Quadcopter. These angles have to satisfy the equations of motion to produce stable Quadcopter control. Position equations of motion: The position of the Quadcopter in space can be represented by three coordinates (X, Y, and Z). These three coordinates must also satisfy the equations of motion to maintain the Quadcopter's stability. Rotational dynamics: To calculate the rotational dynamics of the Quadcopter, one must determine its moments of inertia and angular velocity.
Step 1: Mathematical Model Derivation The mathematical model of a Quadcopter is derived using the following equations: Rotation angle equations of motion: ϕ = φ θ = θ ψ = ψ Position equations of motion: X = X Y = Y Z = Z
Rotational dynamics: Jx [p dot - (q sin(ϕ) + r cos(ϕ))] = Jy [q dot - (p sin(ϕ) + r cos(ϕ))] = M Jz [r dot - (q sin(ϕ) + p cos(ϕ))] = N Translational dynamics After completing the LQR design, the block diagrams are used to design the system in Simulink. Different blocks are used to represent the various components of the control system. The final block diagram provides the simulation results for the system.
To know more about model visit:
https://brainly.com/question/32332387
#SPJ11
If the transformer of a single-transistor forward converter has a turns ratio of 2:1 between the primary winding (N1) and the reset winding (N3), what is the maximum duty cycle for the forward converter? (Please provide your answer to two decimal places, e.g. 0.33 instead of 1/3. You will receive O mark for this question if the format is wrong even the answer is correct.)
The maximum duty cycle is 0.67.
The maximum duty cycle for the forward converter if the transformer of a single-transistor forward converter has a turns ratio of 2:1 between the primary winding (N1) and the reset winding (N3) is 0.67.
Here's how to obtain it:
In a forward converter, the maximum duty cycle is determined by the relationship between the input voltage, the output voltage, and the turns ratio of the transformer. The reset winding is a secondary winding in the transformer. It provides a voltage that is opposite in polarity to the voltage on the primary winding during the reset period.
The maximum duty cycle (D) of the forward converter is given by the equation below: $$D = 1 - \frac{V_{out}}{V_{in}} = \frac{N_1}{N_1 + N_3}$$
Where: Vout is the output voltage Vin is the input voltageN1 is the number of turns on the primary windingN3 is the number of turns on the reset winding
From the problem statement, we are given that the turns ratio between the primary and reset windings is 2:1, which means that N3 = N1/2.
Substituting this value into the equation above, we get: D = 1 - (Vout / Vin) = N1 / (N1 + N1/2) = N1 / (3N1/2) = 2/3 = 0.67
Hence, the maximum duty cycle is 0.67.
To know more about duty cycle refer to:
https://brainly.com/question/15123741
#SPJ11
(a) An amplitude modulated (AM) DSBFC signal, VAM can be expressed as follows: Vm VAM = V₁ sin(2nfet) +- cos 2nt (fc-fm) - Vm 2 2 where, (i) Vc = amplitude of the carrier signal, Vm = amplitude of the modulating signal, (iv) fe = frequency of the carrier signal and, fm = frequency of the modulating signal. cos 2πt (fc + fm) Suggest a suitable amplitude for the carrier and the modulating signal respectively to achieve 70 percent modulation. [C3, SP4] (ii) If the upper side frequency of the AM signal is 1.605 MHz, what is the possible value of the carrier frequency and the modulating frequency? [C3, SP4] Based on your answers in Q1(a)(i) and Q1(a)(ii), rewrite the expression of the AM signal and sketch the frequency spectrum complete with labels. [C2, SP1] What will happen to the AM signal if the amplitude of carrier signal remains while the amplitude of the modulating signal in Q1(a)(i) is doubled? [C2, SP2]
To achieve 70 percent modulation in an amplitude modulated (AM) DSBFC (Double Sideband Full Carrier) signal, we can determine suitable values for the carrier and modulating signal amplitudes.
Let's go through the steps to find these values and address the subsequent questions. (i) Suitable amplitude for the carrier and modulating signal:
To achieve 70 percent modulation, the modulation index (m) is given as:
m = Vm / Vc
Since we want 70 percent modulation, we set m = 0.7.
Given that Vm is the amplitude of the modulating signal, we can find the amplitude of the carrier signal (Vc) by rearranging the formula:
Vm = m * Vc
Therefore, in order to achieve 70 percent modulation, the amplitude of the carrier signal should be higher than the amplitude of the modulating signal.
(ii) Finding the carrier and modulating frequencies:
The upper side frequency of the AM signal is given as 1.605 MHz. To find the possible values of the carrier and modulating frequencies, we need to consider the relationship between the upper side frequency (fu) and the carrier and modulating frequencies.
fu = fc + fm
Given that fu = 1.605 MHz, we can rewrite the equation as:
fc = fu - fm
Based on this information, we need to know the value of the modulating frequency (fm) to determine the possible value of the carrier frequency (fc).
(iii) Rewriting the expression of the AM signal and sketching the frequency spectrum:
Without the specific values for the carrier and modulating frequencies, we cannot provide a complete expression of the AM signal or sketch the frequency spectrum. Please provide the values of the carrier and modulating frequencies so that we can proceed with answering this part of the question.
(iv) Effect of doubling the amplitude of the modulating signal:
If we double the amplitude of the modulating signal (Vm), while keeping the amplitude of the carrier signal (Vc) the same, the modulation index (m) will increase.
As a result, the amplitude of the sidebands in the frequency spectrum will also increase. This will lead to a higher magnitude in the modulated signal, resulting in a stronger modulation effect. The signal will have a wider range of amplitudes, which can potentially cause distortion or saturation in the output signal if it exceeds the limits of the system.
It's worth noting that doubling the amplitude of the modulating signal may not necessarily result in a linear doubling of the modulation index. The relationship between the amplitude of the modulating signal and the modulation index is dependent on the specific characteristics of the modulation scheme and system being used.
Learn more about amplitude modulated here:
https://brainly.com/question/33223009
#SPJ11
a)What are the main benefits of DTC (Direct torque
control)technology over traditional AC drive technology?
Direct Torque Control (DTC) technology is better than traditional AC drive technology in many ways. The main benefits of DTC (Direct Torque Control) technology over traditional AC drive technology are as follows:
DTC technology has more precise torque control and better dynamic performance compared to traditional AC drive technology. This is because DTC technology uses a hysteresis controller that directly controls the torque and flux of the motor, which makes it possible to provide higher accuracy in torque control. DTC technology is also more flexible and can work with a wider range of motor types, including induction motors, permanent magnet motors, and synchronous reluctance motors.DTC technology has a faster torque response time compared to traditional AC drive technology. This is because DTC technology can respond to changes in torque quickly, without the need for complex feedback loops or sensors. This makes DTC technology ideal for applications that require high-speed torque control, such as robotics, machine tools, and conveyor systems.DTC technology is more energy-efficient compared to traditional AC drive technology.
This is because DTC technology can provide better control over the motor's torque and speed, which can reduce energy losses and improve overall system efficiency. In addition, DTC technology can use advanced control algorithms to optimize the motor's energy consumption, which can further improve energy efficiency.Explanation:DTC technology is a relatively new technology that has been developed to provide more precise and efficient control of electric motors. This technology is based on a hysteresis controller that directly controls the torque and flux of the motor, which makes it possible to provide higher accuracy in torque control. DTC technology is also more flexible and can work with a wider range of motor types, including induction motors, permanent magnet motors, and synchronous reluctance motors. In addition, DTC technology has a faster torque response time compared to traditional AC drive technology, making it ideal for applications that require high-speed torque control. Overall, DTC technology is a highly advanced and efficient technology that offers many benefits over traditional AC drive technology.
Learn more about torque Here.
brainly.com/question/31323759
#SPJ11
A centrifugal compressor is steadily supplied with air at 150 kPa and 30 C; 5 kg/second of air is flowing. The compressor outlet pressure is 750 kPa, during the process the rate of heat removal from the air is 0.5 kW. Exit temperature of air compressor is 500 C. a. Write the steady state energy equation for the compressor. b. Determine the power required to compress the air.
Given that a centrifugal compressor is steadily supplied with air at 150 kPa and 30°C. 5 kg/second of air is flowing. The compressor outlet pressure is 750 kPa, during the process the rate of heat removal from the air is 0.5 kW.
Exit temperature of air compressor is 500°C.a. Steady State Energy Equation:steady state energy equation for the compressor is given as:Qdot-Wdot_m = ΔHwhere Qdot is the heat removal rate from the air, Wdot_m is the power input to the compressor, and ΔH is the enthalpy change of the air between the inlet and exit of the compressor.b. Power Required to Compress the Air:
The power required to compress the air can be calculated as shown below:For isentropic compression,ΔH = Cp(Exit Temperature - Inlet Temperature)Wdot_m = Qdot/ηiwhere ηi is the isentropic efficiency of the compressorWdot_m = (0.5/ηi) kWWe have, Power required to compress the air is 474.35/ηi kW, where ηi is the isentropic efficiency of the compressor. Hence, the to the question is that the power required to compress the air is 474.35/ηi kW.
To know more about power visit:
https://brainly.com/question/33466951
#SPJ11
Calculate the frequency of a pulse generator if the pulse width is 175 ns and the percentage duty cycle of the signal is 35%.
Frequency of a pulse generator is a measure of the number of pulses that a generator produces per second. It is measured in Hertz (Hz) and can be calculated using pulse width (PW) and duty cycle (DC) of the pulse signal.
If the pulse width is 175 ns and the percentage duty cycle of the signal is 35%, then the frequency of the pulse generator can be calculated as follows:Step 1: Calculate the pulse repetition time (PRT) using the following formula: PRT = PW / DC = 175 ns / 35% = 500 ns
Step 2: Calculate the frequency using the following formula:Frequency = 1 / PRT = 1 / 500 ns = 2 MHz Therefore, the frequency of the pulse generator is 2 MHz.
To now more about Frequency visit:
https://brainly.com/question/29739263
#SPJ11
(a) Briefly describe the FOUR main losses that occur in real transformers, and how they are represented in the transformer equivalent circuit. (b) Given the primary and secondary windings of 400 and 250 turns respectively, primary voltage of 208V and primary current of 2A, determine the secondary voltage and current of the transformer. (c) The open- and short-circuit tests performed on a 15kVA, 2300/230V transformer gives the following observations: Open-circuit test Short-circuit test (performed on low voltage side) (performed on high voltage side) Voc=230V V sc = 47V Ioc = 2.1A Poc=50W Isc = 6.0A Psc = 160W (i) Determine the impedances Req, Xeq, Re and Xm of the transformer. (ii) Sketch the approximate equivalent circuit referred to the primary side. (d) Briefly describe autotransformers, and what they are mainly used for. Question 3 (a) A shunt DC generator has the following data: Rated power P, = 8kW, Rated terminal voltage Vr = 160V, Armature resistance R₁ = 0.292, Shunt field resistance RF = 400 (i) Draw the equivalent circuit of the generator. (ii) Calculate the induced voltage Е at rated load. Assume there is a brush contact drop of about 2V.
The four main losses that occur in real transformers, and how they are represented in the transformer equivalent circuit are as follows: Copper losses (I²R losses) occur in the primary and secondary windings and are represented by resistors in the equivalent circuit.
Core losses (Hysteresis and Eddy current losses) occur in the core and are represented by two components in the equivalent circuit, resistance Rm and reactance Xm. These losses are constant for all loads and vary with the frequency.Load losses (Stray losses) occur in the windings and vary with the load. They are also represented by resistance RL and reactance XL in the equivalent circuit.Magnetizing current losses occur in the core and are represented by reactance Xm in the equivalent circuit.(b)Given the primary and secondary windings of 400 and 250 turns respectively, primary voltage of 208V and primary current of 2A. To determine the secondary voltage and current of the transformer we need to use the turns ratio of the transformer.
Turns ratio, N = number of turns in secondary / number of turns in primary N = 250 / 400 = 0.625 The secondary voltage is given asVs = N * VpVs = 0.625 * 208 = 130VSecondary current is given asIs = Ip / NIs = 2 / 0.625 = 3.2A(c)The impedances Req, Xeq, Re and Xm of the transformer can be determined using the following equations:Req = Voc² / Poc = 230² / 50 = 1058 ohmsXeq = ((Voc / Ioc)² - Req²)^(1/2) = ((230 / 2.1)² - 1058²)^(1/2) = 161 ohmsRe = (Psc / Isc²) = 160 / 6² = 4/3 ohmsXm = ((Voc / I0)² - Re²)^(1/2) = ((230 / 0)² - (4/3)²)^(1/2) = 49,062 ohmsThe approximate equivalent circuit referred to the primary side is shown in the figure below(d) Autotransformers are transformers where the primary and secondary windings share a common winding.
To know more about real transformers visit :-
https://brainly.com/question/13658057
#SPJ11
A short-shunt machine has armature, shunt and series field resistances of 0.05 0 and 400 and 0.8 0 respectively. When driven as a generator at 952 rpm, the machine delivers 32 kW at 400 V. Calculate Generator developed power 1.1 1.2 Generator efficiency 1.3 Developed power when running as a motor taking 32 kW from 400 V 1.4 Full load motor torque
1. Calculation of generator developed power:
Given data:
Armature resistance (Ra) = 0.05 ohm
Shunt field resistance (Rsh) = 0 ohm
Series field resistance (Rs) = 400 ohm
Series field current (Is) = 0.8 A
Speed of the generator (N) = 952 rpm
Output voltage (V) = 400 V
Output power (Pg) = 32 kW
The formula for generator developed power is given by,
Pg = (V - Ia Ra) Ia
Where,
Ia = Armature current
V = Output voltage
The armature current (Ia) is given by,
Ia = (V / (Ra + Rsh)) - (Is / (Ra + Rs))
Substituting the values in the above equation, we get
Ia = (400 / (0.05 + 0)) - (0.8 / (0.05 + 400))
Ia = 398.80 A
Now, substituting the values of Ia, Ra, and V in the formula of generator developed power, we get
Pg = (V - Ia Ra) Ia
Pg = (400 - 398.8 x 0.05) x 398.8
Pg = 15.86 kW
Therefore, the generator developed power is 15.86 kW.
2. Calculation of generator efficiency:
The formula for generator efficiency is given by,
Generator efficiency = Output power / Input power
Input power = Power drawn from the prime mover
In this case, the power drawn from the prime mover is equal to the output power. Therefore,
Input power = Output power = 32 kW
Substituting the values in the formula of generator efficiency, we get
Generator efficiency = Output power / Input power
Generator efficiency = 15.86 / 32
Generator efficiency = 0.495625 or 49.56%
Therefore, the generator efficiency is 49.56%.
3. Calculation of developed power when running as a motor:
When the machine is running as a motor, it will take 32 kW of power from the supply. Therefore, the developed power will also be 32 kW.
4. Calculation of full-load motor torque:
The formula for full-load motor torque is given by,
T = (9.55 x P) / N
Where,
P = Power in kW
N = Speed in rpm
Substituting the values in the above equation, we get
T = (9.55 x 32) / 952
T = 0.32 Nm
Therefore, the full-load motor torque is 0.32 Nm.
To know more about Armature visit:
https://brainly.com/question/29649379
#SPJ11
1.) A wastewater pump delivers wastewater into a 3-m per side cubical tank at the rate of 300L/min. The specific gravity of the wastewater is 1.2. Calculate the mass flow rate of wastewater delivered in kg/s and the time required to completely fill the tank in hours.
2.) The compressor of a large gas turbine power plant receives 12kg/s of surrounding air at 95kPa and 20°C. At the compressor outlet, air exits at 1.52MPa, 430°C, Determine the flow energy requirements in MW.
1) The time required to completely fill the tank is 1.5 hours. 2) The flow energy requirements are 6.62 MW.
1.)Given values:
Rate of flow (Q) = 300L/min = 0.3 m³/min
Density (ρ) = Specific gravity (SG) x Density of water (ρw) = 1.2 x 1000 kg/m³ = 1200 kg/m³
Volume of tank (V) = 3m x 3m x 3m = 27 m³
To find:
Mass flow rate of wastewater (ṁ) and time required to completely fill the tank (t)
Formula:
ṁ = Q x ρt = V / Q
Calculation:
ṁ = 0.3 m³/min x 1200 kg/m³= 360 kg/min = 6 kg/s
Therefore, the mass flow rate of wastewater delivered in kg/s is 6 kg/s.t = V / Qt = 27 m³ / 0.3 m³/min= 90 minutes = 1.5 hours
Therefore, the time required to completely fill the tank is 1.5 hours.
2.)Given values:
Mass flow rate (m) = 12 kg/sInlet pressure (P1) = 95 kPa
Outlet pressure (P2) = 1.52 MPa
Inlet temperature (T1) = 20°C
Outlet temperature (T2) = 430°CTo find:
Flow energy requirements (W)
Formula: W = m x (h2 - h1)
where h = cp x T for air
Calculation: cp for air = 1.005 kJ/kg.
K for temperatures less than 1000 K (isobaric specific heat capacity)h1 = cp x T1 = 1.005 kJ/kg.
K x (20 + 273) K= 292.4 kJ/kg.h2 = cp x T2 = 1.005 kJ/kg.
K x (430 + 273) K= 812.3 kJ/kg
W = m x (h2 - h1)= 12 kg/s x (812.3 - 292.4) kJ/kg= 6618.96 kW = 6.62 MW
Therefore, the flow energy requirements are 6.62 MW.
Learn more about Density here:
https://brainly.com/question/29775886
#SPJ11
Input voltage is 20 to 30 [V]. The output voltage is 24 [V]. Load power is 100 [W]. There is a boost converter with a switching frequency [kHz). Find the minimum value of the inductor to operate in the CCM and the capacitor value so that the ripple of the output voltage is less than 1%.
The Boost converter is a DC to DC converter with a high output voltage than the input voltage.
The output voltage is given by the formula, Output voltage, Vo = Vin x (1 + D) / D where D is the duty cycle Duty cycle, D = Vo / (Vin + Vo)For the given problem, Minimum value of inductor (L) is calculated using the formula, Minimum value of inductor ,L = (Vin x D x (1 - D)) / (fs x ΔIL)where ΔIL is the inductor ripple currentΔIL = (Vin - Vo) / (2 x L x fs)The ripple voltage of the output capacitor is given by the formula, Ripple voltage of output capacitor, ΔVo = (Ic x Δt) / C where Ic is the capacitance current and Δt is the time period. The capacitance current is given by ,Ic = P / Vo where Vo is the output voltage and P is the load power.ΔVo = (P x Δt) / (Vo x C)Substituting the given values, Ripple of output voltage (Vo) ≤ 1% 1% of Vo = (1 / 100) x 24= 0.24VSo, ΔVo = 0.24V Ic = 100/24 = 4.17AAlso, Δt = (1 / fs) = (1 / 10)ms = 100μsSo, C = (Ic x Δt) / ΔVoC = (4.17 x 100 x 10^-6) / 0.24C = 1.736 x 10^-4 F Minimum value of inductor, L = (Vin x D x (1 - D)) / (fs x ΔIL)ΔIL = (Vin - Vo) / (2 x L x fs)ΔIL = (30 - 24) / (2 x L x 10 x 10^3)ΔIL = 3 / (L x 10^4)L = (20 x 24/ (30 + 24)) = 15.4[V]D = 24 / (30 + 24) = 0.444Minimum value of inductor, L = (20 x 0.444 x (1 - 0.444)) / (10 x 3 / (L x 10^4))L = 3.867 x 10^-4 H or 386.7 μFSo, the minimum value of the inductor is 386.7 μF and the capacitor value is 1.736 x 10^-4 F to operate in the CCM and the ripple of the output voltage is less than 1%.
To know more about converter visit:-
https://brainly.com/question/33213965
#SPJ11
How many times can the following exposures be made safely, assuming the machine is single-phase: 100 kVp, 500 mA, 850 msec, 40 inch SID?
When taking X-ray exposures, the number of times that can be safely made is determined by the machine's maximum capacity. For a machine that is single-phase, 100 kVp, 500 mA, 850 msec, 40 inch SID, the safe number of times that the exposure can be made is as follows:
Let's use the formula kVp x mA x seconds x correction factor = mAskVp = 100mA = 500s = 850mAs = ?Correction factor = 1 (since the machine is single-phase)Using the above formula, we can rearrange it to mAs = kVp x mA x seconds x correction factormAs = 100 x 500 x 0.85 x 1mAs = 42,500Therefore, 42,500 mAs is the total amount of radiation that the machine can safely produce. However, to determine the number of times that it can be produced, we need to divide the total by the mAs per exposure.If, for example, the mAs per exposure is 10, then the number of times that it can be safely produced is:42,500/10 = 4,250 exposures. Therefore, assuming that the machine is single-phase, the number of times that can safely be made is 4,250, given a 100 kVp, 500 mA, 850 msec, 40 inch SID and an mAs per exposure of 10.
learn more about X-ray exposures here,
https://brainly.com/question/17108516
#SPJ11
ACCORDING acoustic impedance of matching layer %ultrasound transducers% Please prove the following formula
,,Zm1=(Zpc*Ztis )^0.5.. by the relationship T=(2*Z2/(Z2+Z1))...for many step and explanition
we can say that the formula "Zm1 = (Zpc * Ztis)^0.5" is correct. The formula to prove is "Zm1=(Zpc*Ztis )^0.5". This can be proven using the relationship T=(2*Z2/(Z2+Z1)). I t is known that the reflection coefficient is given as "R = (Z2 - Z1) / (Z2 + Z1)" where Z2 is the acoustic impedance of the second medium and Z1 is the acoustic impedance of the first medium.
In the case of ultrasound transducers, the second medium is the body tissue and the first medium is the matching layer.So, the matching layer is designed such that it has an acoustic impedance which is intermediate between that of the transducer and the body tissue. If Zpc is the acoustic impedance of the piezoelectric ceramic and Ztis is the acoustic impedance of the body tissue,
then the acoustic impedance of the matching layer is given as:Zm1 = (Zpc * Ztis)^0.5 ... equation 1The relationship between the reflection coefficient and the transmittance T is given by:T = 1 - R = (Z2 - Z1)^2 / (Z2 + Z1)^2 ... equation 2Using equation 1, we can write Z2 / Z1 = Ztis / Zm1 = (Zpc * Ztis / Zm1 / Zpc) = Ztis / Zpc * Zpc / Zm1Substituting this in equation 2, we get:T = (Ztis / Zpc * Zpc / Zm1 - 1)^2 / (Ztis / Zpc * Zpc / Zm1 + 1)^2 ... equation 3If the matching layer has an ideal acoustic impedance (i.e. if it is perfectly matched), then Zm1 = Zpc * Ztis / (Zpc + Ztis) and Zm1 / Ztis = Zpc / (Zpc + Ztis).
To know more about acoustic impedance visit :-
https://brainly.com/question/30498894
#SPJ11
a) A discrete-time system is described by the following difference equation: y (1) = 0.2[x() + X(n-1) + (-2) + x(x - 3) + (-4)] where (n) and y(n) are the system's input and output, respectively. (i) Determine and sketch the output of the system, ), when the input, xín), is a unit impulse function w). (4 Marks) (ii) State whether the system is stable and/or memoryless. Substaritiate your answer. (4 Marks) (iii) Describe the functionality of the system, i.e. what the system does.
The impulse response of the system is h(n) = 0.2[δ(n) - 3δ(n-1) - 2δ(n+1)], which confirms that the system is a high-pass filter.
(i) To find the output of the system, we can substitute the input as a unit impulse function w(n), i.e. w(n) = δ(n). Substituting this value of input into the difference equation,y (1) = 0.2[x(0) + x(-1) - 2x(1) + x(1) - 3x(0) - 4]
Thus, the output is given by y(1) = 0.2[-4] = -0.8
(ii) The system is memoryless, since the output y(n) depends only on the input x(n) and not on any previous values of the input or output. However, it is not stable since the impulse response h(n) is not absolutely summable.
(iii) The functionality of the system can be determined by analyzing the difference equation. The system is linear since it has a linear difference equation. It is time-invariant since the coefficients of the equation are constant and do not vary with time. The system can be considered as a high-pass filter since the output is determined mainly by the difference between the current input sample and the previous input sample.
The impulse response of the system is h(n) = 0.2[δ(n) - 3δ(n-1) - 2δ(n+1)], which confirms that the system is a high-pass filter.
To know more about impulse visit:
brainly.com/question/33367613
#SPJ11
Q:To design 4 bit binary incremental in simple design we need 4 Full Adders 4 Half Adders 4 OR gates and 8 NOT gates O4 XOR gates and 4 AND gates *
To design a 4-bit binary incremental circuit, you would need the following components: 4 Full Adders: Each Full Adder takes three inputs (A, B, and carry-in) and produces two outputs (sum and carry-out). In this case, you would need 4 Full Adders to handle the addition of the 4-bit binary numbers.
- 4 Half Adders: Each Half Adder takes two inputs (A and B) and produces two outputs (sum and carry). These are used to handle the addition of the least significant bit (LSB) of the binary numbers.
- 4 OR gates: The OR gates are used to combine the carry-out outputs of the Full Adders to generate the final carry-out for the 4-bit addition.
- 8 NOT gates: The NOT gates are used to invert the inputs to the Full Adders and Half Adders as needed.
- 4 XOR gates: The XOR gates are used to perform the bit-wise addition of the binary numbers.
- 4 AND gates: The AND gates are used in combination with the XOR gates to generate the carry-in inputs for the Full Adders and Half Adders.
By using these components, you can design a 4-bit binary incremental circuit that can increment a 4-bit binary number by 1. Each Full Adder handles one bit of the binary number, starting from the least significant bit (LSB) and propagating the carry to the next Full Adder.
Note that this is a simplified explanation, and the actual circuit design may vary depending on specific requirements and constraints.
Learn more about binary here:
https://brainly.com/question/33333942
#SPJ11
Differentiate Static and Dynamic Type binding.
Static type binding refers to the association of types to variables at compile-time, while dynamic type binding refers to the association of types to variables at runtime.
Static type binding occurs during the compilation phase of a program. In statically typed languages, the types of variables are determined and checked at compile-time. Once the types are bound, they remain fixed throughout the execution of the program. This means that any operations and interactions involving variables are checked for type compatibility during compilation.
On the other hand, dynamic type binding occurs during runtime in dynamically typed languages. The types of variables are determined and checked at runtime as the program is executing. This allows for greater flexibility as the types of variables can change during the execution of the program. Operations and interactions involving variables are checked for type compatibility dynamically as they are encountered during runtime.
Static type binding and dynamic type binding are different approaches to associating types with variables in programming languages. Static type binding occurs at compile-time and provides type checking and fixed types throughout the program's execution. Dynamic type binding occurs at runtime and allows for more flexibility with changing types during program execution. The choice between static and dynamic type binding depends on the language design and the requirements of the program.
To know more about binding visit
https://brainly.com/question/29833806
#SPJ11
Instructions In this exercise, you will design the class member Type 1. Each object of member Type can hold the name of a person, member ID, number of books bought, and amount spent 2. Include the member functions to perform the various operations on the objects of member Type -for example, modify, set, and show a person's name. Similarly, up-date, modify, and show the number of books bought and the amount spent. 3. Add the appropriate constructors. 4. Write the definitions of the member functions of memberType. 5. Write a program to test various operations of your class member Type memberData.txt memberTypelmp.c... + main.cpp memberType.h 1 #include 2 #include 3 #include 4 #include "memberType.h" 5 6 using namespace std; 7 8 int main() 10 // Write your main here. 11 return 0; 12] 13 main.cpp memberType.h memberData.txt memberTypelmp.c... + Σ. 14 2 10 3 John Williams 4 5 6 20 7 Lisa Berry 8 2 9 35.50 10 30 11 Ron Brown 12 10 13 255.68 14 40 15 Jessey Smith 16 0 17 0 18
To design the class memberType, include member variables for name, member ID, number of books bought, and amount spent. Implement member functions to modify and display the data. Use appropriate constructors.
To design the class memberType, we need to define the member variables and member functions based on the given requirements. Here's an example implementation: In this implementation, the memberType class has private member variables for name, member ID, number of books bought, and amount spent. It also includes appropriate constructors to initialize the member variables. The member functions setName, setNumOfBooksBought, and setAmountSpent are provided to modify the corresponding data. The displayMemberInfo function is used to display the information of a member object. In the main function, four member objects are created with different data. Their information is displayed using the displayMemberInfo function. This implementation allows for creating and manipulating member objects, setting their data, and displaying the information as required.
learn more about memberType here :
https://brainly.com/question/31200833
#SPJ11
List the five general function modules inside the integrated
PWM-controller of the switching power supply.
The specific function modules inside an integrated PWM-controller of a switching power supply can vary depending on the design and manufacturer.
However, some general function modules that may be found in such a controller include:
Voltage reference module: Provides a stable reference voltage for comparison with the output voltage to maintain a constant output voltage.
Oscillator module: Generates a signal to control the switching frequency of the power supply.
Error amplifier module: Compares the voltage feedback signal with the voltage reference signal to determine if the output voltage is too high or too low. It then sends a signal to adjust the duty cycle of the pulse width modulation (PWM) signal accordingly.
PWM comparator module: Compares the error amplifier output with the oscillator waveform to generate the PWM signal that controls the switching of the power supply.
Protection module: Includes overvoltage protection, overcurrent protection, and other safety features to protect the power supply and connected devices from damage.
Again, the specific function modules included in an integrated PWM-controller may vary depending on the design and manufacturer, but these are some of the general modules that are commonly found.
learn more about PWM-controller here
https://brainly.com/question/33462878
#SPJ11
Design a regulated power supply using a bridge rectifier, capacitors, and Zener diode (no Integrated Circuit). The source voltage is 110±10 Vrms, 60 Hz frequency. The output voltage is as follows (±5%) : Type 1: 6 V
Design a regulated power supply using a bridge rectifier, capacitors, and Zener diode (no Integrated Circuit). The source voltage is 110±10 Vrms, 60 Hz frequency. The output voltage is 6 V. The rating of the adapter will be 1 W and 5% regulation
The power supply can be designed using a bridge rectifier, capacitors, and Zener diode.
Here is the design of a regulated power supply:
Type 1: 6V
Given Source Voltage= 110±10 Vrms
= 110 + 10
= 120V (Maximum)
Given Output Voltage = 6V ± 5%
= 6V ± 0.3V
Minimum Output Voltage = 5.7V
Maximum Output Voltage = 6.3V
So, taking the maximum voltage into account, the output voltage is 6.3V.
Let's find out the value of the Capacitors and Zener diode
Resistor value for the Zener diode:
For 6.3V, we can take a 5.1V zener diode.
A 1W zener diode can take maximum power = 1W.
If R is the load resistance, V is the input voltage and Vz is the zener voltage, then the resistor R required is given by:
[tex]R = \frac{{({V_s} - {V_z})^2}}{P}[/tex]
Where
P = 1W, Vs = 120V, Vz = 5.1V
[tex]R = \frac{{(120 - 5.1)^2}}{1}[/tex]
= 14,141\Omega
So, a 14k resistor will be used.
Capacitor value for rectification:
Now, we need to find the value of the capacitor for rectification.
Average DC Voltage = (Vmax-Vmin)/piFor full-wave rectifier, the average voltage is given by:
[tex]V_{avg} = \frac{{{V_s}}}{\pi }[/tex]
For given source voltage,
Vavg = 38V
I = [tex]\frac{{P}}{{{V_s}}}[/tex]
= [tex]\frac{1}{{120}}[/tex]
= 0.008A
Where, P = 1W, Vs = 120V
Current through the diode = 0.008A.
Capacitance required is given by:
[tex]C = \frac{I \times T}{V_{ripple}}[/tex]
Where T = 1/f = 1/60 = 0.0167s (time period) and Vripple = 1.4V.
1.4V ripple is taken for full-wave rectification.
[tex]C = \frac{0.008 \times 0.0167}{1.4}[/tex]
= 0.000095
F = 95µF
Therefore, a 14k resistor, 95µF capacitor, and 5.1V zener diode are used in the design of the power supply.
To know more about rectification visit;
https://brainly.com/question/30360755
#SPJ11
what logic circuit design can control the overflow and underflow in
a quadrature encoder using prime quartus
To control the overflow and underflow in a quadrature encoder using Prime Quartus, you can design a logic circuit that utilizes a counter and appropriate combinational logic.
Here's a high-level overview of the logic circuit design:
1. **Counter**: Start by implementing a counter that keeps track of the quadrature encoder's position. The counter should have enough bits to accommodate the expected range of encoder positions. For example, if the encoder has 360 pulses per revolution, a 10-bit counter would allow for 1024 positions.
2. **Decoder**: Next, design a decoder circuit that translates the counter's binary output into corresponding encoder states. The decoder should generate signals for each state transition (A+, A-, B+, B-), based on the current counter value.
3. **Overflow and Underflow Detection**: Implement logic to detect overflow and underflow conditions. When the counter reaches its maximum value (overflow), it should trigger an overflow signal. Similarly, when the counter reaches its minimum value (underflow), it should trigger an underflow signal. You can use comparators and additional logic gates to detect these conditions based on the counter's value.
4. **Control Logic**: Connect the overflow and underflow signals to the control logic. Depending on your specific requirements, you can design the control logic to perform different actions when an overflow or underflow is detected. This may include limiting the counter's range, generating interrupt signals, or modifying the output behavior of the quadrature encoder.
By combining the counter, decoder, overflow/underflow detection, and control logic, you can design a logic circuit that effectively handles overflow and underflow conditions in a quadrature encoder using Prime Quartus. The specific implementation details and circuitry will depend on your application's requirements and the capabilities of the target hardware.
Learn more about Prime Quartus here:
https://brainly.com/question/33223560
#SPJ11
roblem \( 3 \quad(20 \) points) A. For the following circuit find the Thevenin impedance, the Thevenin voltage, and the Norton current. B. Determine the maximum power that can be delivered to a load c
Thevenin Impedance, Thevenin Voltage, and Norton CurrentThevenin impedance (Zth) is calculated by removing the load and shorting out the voltage source and then calculating the total resistance.
Zth = R1||(R2+R3)Where, R1 = 4Ω, R2 = 8Ω, R3 = 12ΩZth = 2.4ΩThevenin Voltage (Vth) is calculated by putting a voltmeter across the output of the circuit when the load is removed.
Vth = 36VThe Norton current (In) can be found by calculating the short circuit current when the load is removed.In = Vth/Zth = 36V/2.4Ω = 15Ampb. Maximum Power Delivered to the LoadTo determine the maximum power delivered to the load, we need to calculate the load resistance value.
The load resistance should be equal to the Thevenin impedance value.Load resistance = Zth = 2.4ΩThe maximum power transfer to the load (Pmax) is found by using the following formula:Pmax = (In^2)*RL
Where, RL = load resistance = 2.4ΩPmax = (15A)^2 * 2.4Ω = 540W , the maximum power that can be delivered to a load is 540W.
To know more about calculating visit:
https://brainly.com/question/30151794
#SPJ11
