Answers
Draw isometric projection Spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn the same.
What is isometric projection?Definition of isometric projection an axonometric projection wherein the 3 spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn same.
An isometric view of an item may be received via way of means of selecting the viewing path such that the angles among the projections of the x, y, and z axes are all of the same, or 120°. For example, with a cube, that is achieved via way of means of first searching immediately toward one face.
Read more about the data:
https://brainly.com/question/25749514
#SPJ1
Related Questions
4.5% complete Question Select the methods of containment based on the concept of isolation. (Select all that apply.) A.Blackhole B.Sinkhole C.Physical disconnection/air gapping D.Sandboxing
Answers
Answer:
A. Blackhole
C. Physical disconnection/air gapping
D. Sandboxing
Here are the methods of containment based on the concept of isolation:
Physical disconnection/air gapping is the most effective method of isolation, separating the infected system from the rest of the network.
How does sandoxing work?Sandboxing isolates the infected system in a controlled environment, allowing analysis and cleaning without affecting the rest of the network. Quarantine isolates the infected system from the rest of the network until it can be cleaned, preventing it from infecting other systems.
The following methods are not based on the concept of isolation:
Blackhole: This is a method of redirecting malicious traffic to a dead end. This does not isolate the infected system, but it does prevent the malicious traffic from reaching other systems on the network.
Sinkhole: This is a method of redirecting malicious traffic to a honeypot. This does not isolate the infected system, but it does allow security researchers to collect information about the malicious traffic.
Therefore, the methods of containment based on the concept of isolation are Physical disconnection/air gapping, Sandboxing, and Quarantine.
Read more about Quarantine here:
https://brainly.com/question/1597166
#SPJ2
What is the first test you should do when checking the charging system?
Answers
Answer:
Connect the test light in series with the negative post, and start pulling feed wires. The first to check is the heavy charging wire from the alternator. A bad or leaky diode in an alternator is a very common source of overnight battery drain. Connect wires one at a time to see what lead is drawing current.
Please show NEC article 310.10(H)
Answers
Conductors in Parallel is covered in 310.10(H). Often when working with higher ampacities, we find it to be cumbersome and expensive to keep increasing the size of the wire and conduit. The solution is often to use multiple runs that are connected to a common location on each end. Notice in the 2011 edition of the code that much of this section is highlighted gray, indicating new or revised text. The change here was that the previous code stated that you were permitted to parallel conductors 1/0 AWG and larger; however, it didn’t specifically prohibit you from paralleling smaller conductors, which was the intent and the way it was enforced in all my years of enforcement. However, that’s not what the actual language said, and ambiguous language cancause enforcement issues; therefore, in the 2011 code it was made clear that you are only allowed to parallel conductors 1/0 AWG and larger.
In a basketball game, the point guard A intends to
throw a pass to the shooting guard B, who is breaking
toward the basket at a constant speed of 12 ft /sec. If
the shooting guard is to catch the ball at a height
of 7 ft at C while in full stride to execute a layup,
determine the speed v0 and launch angle with
which the point guard should throw the ball
Answers
In a basketball game, point guard A intends the speed as 47.76 ft/sec, and the launch angle will be 41.084°.
What is the projectile motion?The projectile motion is given as the motion of the object in the curved path near the earth's surface. The throwing of the ball will follow the projectile motion.
The missing image is attached below.
The given game situation consists of:
Velocity of shooting guard (vs) = 12 ft/sec.
Distance from B to C (sc) = 20 ft
Final height to catch the ball, 7 ft
The total distance to cover from B to C = 60 ft
Time is taken to reach B to C = Distance/Speed
Time to reach B to C = 20ft/12ft/sec
Time to reach B to C = 1.667 sec.
The time taken to cover the horizontal distance:
Distance = Velocity * Time
60³ = v₀cosθ * distance/time
60³ = v₀cosθ * 20/12
v₀cosθ = 36 ft/sec
The vertical movement can be given where, g = 32.2 ft/sec²:
s = s₀ + v₀sinθ * time + 1/2 -g time²
7 = s + v₀sinθ * 20/12 - 1/2 32.2 ft/sec² * (20/12)²
v₀sinθ = 31.3875 ft/sec
[tex]\rm v_0 =\sqrt{v_0sin\theta^2\;+\;v_ocos\theta^2}[/tex]
Substituting the values:
v₀ = 47.76 ft/sec
The launch angle for the ball will be:
tanθ = v₀sinθ/v₀cosθ
tanθ = 31.3875/36
tanθ = 0.871
θ = 41.084°
Thus, the speed v₀ of the ball will be 47.76 ft/sec, and the launch angle will be 41.084°.
Read more about projectile motion, here:
https://brainly.com/question/11049671
#SPJ1
If the digital inputs for a supply-air fan control application indicate that the supply-air fan should be on, the controller compares the measured ________ to the set point; if this reading is lower than the setpoint, the supply-air fan speed must be increased.
Answers
If the digital inputs for a supply-air fan control application show that the supply-air fan should be ON, the controller compares the measured static air pressure to the set point.
The operation of a supply-air fan control.Basically, the controller of a supply-air fan control application is designed and developed to compare the measured static air pressure to the set point when its digital inputs indicate that the supply-air fan should be ON.
By design and configuration, if the measurement of the static air pressure is lower than the set point, the supply-air fan speed must be increased by an engineer accordingly.
Read more on supply-air fan here: https://brainly.com/question/15096367
#SPJ12
he minimum number of branch circuits is determined from ____ load and the size (or rating) of the circuits used.
Answers
The minimum number of branch circuits is determined from the total computed load and the size (or rating) of the circuits used.
What is circuit?It should be noted that circuit means a complete circular path that electricity flows through.
In this case, the minimum number of branch circuits is determined from the total computed load and the size (or rating) of the circuits used.
Learn more about circuit on:
brainly.com/question/2969220
#SPJ12
Directions: Correct the errors.
to
1. I went to the library for study last night.
2. Helen borrowed my dictionary for to look up the spelling of "occurred."
3. The teacher opened the window for letting some fresh air in the room.
4. I came to this school for learn English.
5. I traveled to Osaka for to visit my sister.
Answers
Answer:
1. I went to the library to study last night.
2.Helen borrowed my dictionary to look up the spelling of "occurred."
3.The teacher opened the window to let some fresh air into the room.
4..I came to this school to learn English.
5.I traveled to Osaka to visit my sister.
Explanation:
...
3 To improve the acoustics in auditorium, a sound reflector with mass
of 200 kg is suspended by a chain from the ceiling. What is its
weight? What force (magnitude and direction) does the chain exert
on it? What is the tension in the chain? Assume that the mass of the
chain itself is negligible.
Answers
To improve the acoustics in auditorium, a sound reflector with mass of 200 kg is suspended by a chain from the ceiling thus thet force (magnitude and direction) does the chain exert on it =1960 N.
What is Newton's third regulation?
Ths 0.33 regulation states that for each movement (pressure) in nature there's an identical and contrary response. If item A exerts a pressure on item B, item B additionally exerts an identical and contrary pressure on item A. In different words, forces end result from interactions.
Weight of reflector = mg=200^ * 9.8=1960 NForce exerted with the aid of using chain =1960 NDirection = upwardsTension at the chain = weight of reflector=1960 NWeight of reflector =mg =100 * 9.8=980NMagniyof pressure reflector exerts on earth = 980 N(Due to movement response pair of forces, consistent with Newton's 0.33 regulation of motion.Read more about the Newton's law:
https://brainly.com/question/25545050
#SPJ1
When adding two 8 bit binary numbers, which of the following statements is true?
Answers
Answer:
The result might require 9 bits to store
Tech A says that if a CV boot is torn, it can typically be replaced without replacing the entire joint or shaft. Tech B says that worn CV joints can make a clicking noise when driving while making a tight turn. Who is correct
Answers
Both Technician A and Technician B are correct based on the information provided.
When to replace a CV boot?The CV boot on an automobile vehicle should be replaced when it is torn but shouldn't have been torn for too long. Thus, you should just replace the boot when the CV joint is not yet completely damaged or full of dirt.
Similarly, worn CV joints in an automobile vehicle can make a clicking noise when driving while making a tight turn on a road.
Read more on CV joints here: https://brainly.com/question/12239770
#SPJ12
Which thematic group is involved in the transmission and generation of electrical power?
a.Communication Systems
b.Control Systems
c.Computer Systems
d.Energy Systems
e.Electronic Systems
Answers
Answer:
The 17 distinct years Mariah Carey has topped Billboard's Hot 100, spanning an historic four consecutive decades:
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2005
2006
2008
2019
2020
2021
Which of the following is a slow rise of plastic deformation under the action of shear stresses when it is below the yield strength of the material.
a.Brittle Structure
b.Ductile fracture
c.Creep
d.Fatigue
Answers
Creep can be described as a process of the slow rise of plastic deformation under the action of shear stresses when it is below the yield strength of the material. Hence, Option C is correct.
What do you mean by permanent deformation?Permanent deformation can be defined as irreversible, the deformation remains even after the elimination of the carried out forces, at the same time as the transient deformation is recoverable because it disappears after the elimination of carried out forces.
therefore, the correct statement is Option C.
Learn more about permanent deformation
https://brainly.com/question/10667384
#SPJ1
Before installing head gaskets look for “____” labels on the head gaskets
Answers
Before installing head gaskets, you should look for "this side up" or "front" labels on the head gaskets.
What is a head gasket?A head gasket can be defined as a gasket which is fitted between the engine block and the cylinder head in an internal combustion engine, so as to seal oil passages and absorb the pressures of the combustion that occurs inside the engine.
As a general rule, you should look for "this side up" or "front" labels on the head gaskets before installing head gaskets in an internal combustion engine of a vehicle.
Read more on head gaskets here: https://brainly.com/question/1264437
#SPJ1
