during a power demand, the voltage output is reduced by 5.0%. by what percentage is the power on the resistor affected?

Answers

Answer 1

The power on the resistor is affected by a reduction of 9.75% (approximately). This can be calculated using the equation P = V^2/R, where P is power, V is voltage, and R is resistance. If the voltage output is reduced by 5.0%, the new voltage will be 0.95V (where V is the original voltage). Plugging this into the power equation and simplifying, we get:

P' = (0.95V)^2/R
P' = 0.9025V^2/R

To determine the percentage change in power, we can compare P' to the original power P:

% change = (P' - P)/P x 100%
% change = (0.9025V^2/R - V^2/R)/(V^2/R) x 100%
% change = (0.9025 - 1)/1 x 100%
% change = -0.0975 x 100%
% change = -9.75%

Therefore, the power on the resistor is reduced by approximately 9.75% during a power demand that causes a 5.0% reduction in voltage output.


 During a power demand, when the voltage output is reduced by 5.0%, the power on the resistor is affected as follows:

The power (P) on a resistor can be calculated using Ohm's Law: P = V^2 / R, where V is the voltage and R is the resistance of the resistor. If the voltage is reduced by 5%, the new voltage is 0.95V.

Now, we can calculate the new power (P') with the reduced voltage: P' = (0.95V)^2 / R = 0.9025V^2 / R.

To find the percentage change in power, we can use the formula: percentage change = ((P' - P) / P) * 100%.

Plugging in the values, percentage change = ((0.9025V^2 / R - V^2 / R) / (V^2 / R)) * 100% = (0.9025 - 1) * 100% = -9.75%.

So, the power on the resistor is reduced by 9.75% when the voltage output is reduced by 5.0%.

To know more about resistance visit:

https://brainly.com/question/30803596

#SPJ11


Related Questions

When you go out in the sun, it is the ultraviolet light that gives you your tan. The pigment in
your skin called Melanin is activated by the enzyme tyrosinase, which has been stimulated by
ultraviolet light. What is the wavelength of this light if it has a frequency of 7.89 x 10¹4 Hz?

Answers

The wavelength is 380 nm, falling in the UV-A range, stimulating melanin production. Protect skin from excessive UV exposure.

The frequency of the bright light that actuates the development of melanin in the skin can be determined utilizing the recipe λ = c/ν, where λ is the frequency, c is the speed of light, and ν is the recurrence. Subbing the given recurrence of 7.89 x 10¹4 Hz, we get:

λ = c/ν = 3.00 x 10^8 m/s/7.89 x 10¹4 Hz = 380 nm

Consequently, the frequency of the bright light that enacts the development of melanin in the skin is around 380 nanometers. This frequency falls inside the UV-A reach, which is the most harmless type of UV radiation yet can in any case cause skin harm and increment the gamble of skin disease with delayed openness. It is critical to safeguard the skin from exorbitant openness to bright light by utilizing sunscreen, wearing defensive attire, and staying away from the sun during top hours.

To learn more wavelength, refer:

https://brainly.com/question/17603199

#SPJ1

analyze a weather balloon is released into the atmosphere. you know the intial volume, temperature, and air pressure. what information will you need to predict its volume when it reaches its final altitude

Answers

To predict the volume of a weather balloon at its final altitude, you would need to take into account several factors that can affect the behavior of gases at different altitudes.

As the balloon rises in the atmosphere, the air pressure around it decreases. This can cause the gas inside the balloon to expand, which can increase the balloon's volume. To predict the volume of the balloon at its final altitude, you would need to know the air pressure at that altitude.Temperature: The temperature of the gas inside the balloon can also affect its volume. As the balloon rises in the atmosphere, the temperature decreases due to the decrease.Temperature is related to the average kinetic energy of the particles that make up an object or substance. As the temperature of a substance increases, its particles move faster and have more kinetic energy. Conversely, as the temperature decreases, the particles move slower and have less kinetic energy.Temperature is an important concept in many areas of science and technology, including physics, chemistry, meteorology, and engineering. It plays a crucial role in determining the behavior of materials and systems, and is used in a wide range of applications, such as in heating and cooling systems, cooking, and medical treatments.

To know more about temperature visit :

https://brainly.com/question/11464844

#SPJ11

j. j. thomson's work with cathode rays identified the subatomic particle known as the . james chadwick's bombardment of beryllium with alpha particles resulted in the identification of the subatomic particle known as the

Answers

On the other hand, J.J. Thomson's work with cathode rays showed that they were composed of negatively charged particles which he called "corpuscles", now known as electrons.

What is beryllium?

Beryllium is a chemical element with the symbol Be and atomic number 4. It is a light, strong, silvery-white metal that is often found in nature as a free element in minerals. Beryllium is known for its high thermal and electrical conductivity and its strength-to-weight ratio. It is commonly used in aerospace, nuclear, and automotive industries. Beryllium is also used in the production of certain alloys and ceramics, and is used in x-ray machines and other medical equipment. Beryllium compounds can be toxic to humans, so proper handling and safety measures should be taken when working with it.

James Chadwick's work with alpha particles showed that beryllium, when bombarded with alpha particles, released energetic particles with no charge. He identified these particles as the neutron, a subatomic particle with no charge.

To learn more about beryllium

https://brainly.com/question/1582690

#SPJ4

FILL IN THE BLANK. If the voltage across a circuit is quadrupled, then the current through the circuit would be ____.
a. one-fourth as much
b. four times as much
c. unchanged
d. ... nonsense! There would be no way to make such a prediction.

Answers

If the voltage across a circuit is quadrupled, then the current through the circuit would be B. four times as much.

When the voltage across a circuit is quadrupled, the current through the circuit will be four times as much if the resistance of the circuit remains the same. This is because of Ohm's law, which states that the current through a conductor between two points is directly proportional to the voltage across the two points, and inversely proportional to the resistance between them.

Therefore, if the voltage is increased, and the resistance remains constant, the current must also increase proportionally. Conversely, if the voltage is decreased, the current will also decrease proportionally, assuming that the resistance remains constant.

To know more about voltage, click here:-

https://brainly.com/question/13521443

#SPJ11

consider a heat exchanger that is insulated from its surroundings. assuming the inlet and outlet temperatures of the cold fluid, the inlet temperature of the hot fluid, the mass flow rates, and thermal properties are available, without knowing the heat exchanger type and geometrical characteristics (areas, length, etc...), is it possible to calculate the total heat transfer rate, q?

Answers

Without knowing the heat exchanger type and geometrical characteristics (areas, length, etc...),  it is not possible to calculate the total heat transfer rate, q

Define heat transfer.

The transmission of thermal energy between actual objects is known as heat transfer. The second law of thermodynamics states that heat will always move from a hotter to a colder thing. Thermal equilibrium occurs when all of the objects involved and their surroundings attain the same temperature.

A heat exchanger is a device that transfers heat from one working fluid to another. Both cooling and heating operations employ heat exchangers. The fluids could be in direct contact with one another or separated by a solid wall to prevent mixing.

To learn more about heat transfer use:

https://brainly.com/question/2341645

#SPJ4

suppose that there is a passenger of mass 70 kg in the elevator. calculate the apparent weight of the passenger at time t

Answers

The apparent weight of the passenger in the elevator at time t is approximately 476 N.

The apparent weight of the passenger in the elevator, we need to first determine the acceleration of the elevator at time t. We can use Newton's second law of motion, which states that the net force acting on an object is equal to its mass times its acceleration:

ΣF = ma

In this case, the net force acting on the passenger is the force of gravity (mg) minus the force exerted by the elevator on the passenger (N), where N is the normal force or apparent weight of the passenger. Thus, we can write:

mg - N = ma

N = mg - ma

To find the acceleration of the elevator at time t, we need more information about the motion of the elevator, such as its initial velocity, direction of motion, and any external forces acting on it.

Assuming that the elevator is initially at rest and accelerates upward at a constant rate of a = 2 m/s, the apparent weight of the passenger at time t can be calculated as follows:

N = mg - ma = (70 kg)(9.81 m/s) - (70 kg)(2 m/s) ≈ 476 N

Therefore, the apparent weight of the passenger in the elevator at time t is approximately 476 N.

Learn more about apparent weight Visit: brainly.com/question/30142462

#SPJ4

What is a large celestial body that is composed of gas and emits light.

Answers

Answer:

a star

Explanation:

A piece of unknown metal weighs 217 g. When the metal piece absorbs 1.43 kJ of heat, its temperature
increases from 24.5 °C to 39.1 °C. Determine the specific heat of this metal, and predict its identity.

Answers

The specific heat of the metal is  0.389 J/g·°C.

The specific heat of the metal can be calculated using the formula:

q = mcΔT

where q is the heat absorbed, m is the mass of the metal, c is its specific heat, and ΔT is the change in temperature.

Substituting the given values, we get:

1.43 kJ = (217 g) c (39.1 °C - 24.5 °C)

Solving for c, we get:

c = 0.389 J/g·°C

To predict the identity of the metal, we can compare its specific heat to known values for different metals. Based on the calculated specific heat, the metal is likely aluminum or a similar metal with a specific heat close to 0.9 J/g·°C. However, additional tests would be necessary to confirm its identity, such as measuring its melting point, density, and conductivity.

To know more about the Metal, here

https://brainly.com/question/12884841

#SPJ1

A star whose temperature is increasing but whose luminosity is roughly constant moves in what direction on the h-r diagram?.

Answers

A star whose temperature is increasing but whose luminosity is roughly constant moves diagonally to the left on the H-R diagram.

This is because the H-R diagram plots a star's temperature on the x-axis and its luminosity on the y-axis. Stars that are hotter are located towards the left of the diagram, while stars that are more luminous are located towards the top of the diagram. When a star's temperature is increasing but its luminosity is constant, it means that the star is getting smaller. As a star shrinks, it moves diagonally to the left on the H-R diagram, towards the region where smaller, hotter stars are located. This phenomenon is called "subgiant contraction." It is a natural part of a star's life cycle, and it helps astronomers to better understand the evolution of stars.

To know more about temperature visit:

https://brainly.com/question/11464844

#SPJ11

When a double-slit experiment is performed with electrons, what is observed on the screen behind the slits?.

Answers

When a double-slit experiment is performed with electrons, an interference pattern is observed on the screen behind the slits.

The pattern consists of bright and dark fringes, indicating constructive and destructive interference between the waves of the electrons passing through the two slits. This phenomenon lies in the wave-particle duality of electrons. Despite being particles, electrons also exhibit wave-like behavior, with their wave function determining the probability of their location and momentum. When electrons pass through the two slits, their wave functions interfere with each other, creating regions of high and low probability for their detection on the screen.

Thus, the double-slit experiment with electrons demonstrates the wave-particle duality of electrons and the resulting interference pattern that arises from their wave-like behavior. This experiment has important implications for our understanding of quantum mechanics and the nature of reality at the smallest scales.

To know more about double-slit experiment, click here

https://brainly.com/question/28108126

#SPJ11

what is the average range and yield of a modern nuclear weapon (how far can it travel/how big of an explosion will it make)?

Answers

The average range and yield of a modern nuclear weapon vary significantly based on the type of delivery system and the specific weapon used. Typically, the range can be anywhere from 300 to 15,000 kilometers (190 to 9,320 miles), and the yield can range from 0.3 to 50 megatons of TNT equivalent.

There are different types of nuclear weapons and delivery systems, which affect the range and yield of the explosion. For instance, intercontinental ballistic missiles (ICBMs) have a range of up to 15,000 kilometers (9,320 miles), while shorter-range ballistic missiles or aircraft-delivered bombs have a more limited range.

The yield of a nuclear weapon refers to the energy released in the explosion, and it can vary greatly depending on the specific weapon design.

Modern nuclear weapons can range from low-yield tactical weapons of 0.3 megatons or less to strategic weapons with yields of 50 megatons or more.
The range and yield of modern nuclear weapons vary significantly based on factors such as the delivery system and the weapon design.

However, they can generally reach targets at distances of up to 15,000 kilometers (9,320 miles) and create explosions with yields ranging from 0.3 to 50 megatons of TNT equivalent.

For more information on nuclear weapons kindly visit to

https://brainly.com/question/2568750

#SPJ11

the time-domain expressions for three line-to-neutral voltages at the terminals of a y-connected load are

Answers

The time-domain expressions for the three line-to-line voltages are νAB = 288[tex]\sqrt{3}[/tex] cos (ωt - 105°) V, νBC = 288[tex]\sqrt{3}[/tex] cos (ωt - 120°) V, and νCA = 288[tex]\sqrt{3}[/tex] cos (ωt + 30°) V.

What is voltages?

Voltage is an electrical potential energy difference between two points in an electric circuit. It is measured in volts (V). Voltage is used to push electric current through a circuit. It is the work done per unit charge to move the charge from one point to the other. Voltage is a measure of the potential for electrical energy to move between two points in a circuit.

The time-domain expressions for the three line-to-line voltages can be found by taking the difference between two of the line-to-neutral voltages.
νAB = νAN - νBN = 288 cos (ωt - 45°) - 288 cos (ωt - 165°)
  = 576 cos (ωt - 105°) sin (30°)
  = 288[tex]\sqrt{3}[/tex] cos (ωt - 105°) V
νBC = νBN - νCN = 288 cos (ωt - 165°) - 288 cos (ωt + 75°)
 = 576 cos (ωt - 120°) sin (30°)
  = 288[tex]\sqrt{3}[/tex] cos (ωt - 120°) V
νCA = νCN - νAN = 288 cos (ωt + 75°) - 288 cos (ωt - 45°)
  = 576 cos (ωt + 30°) sin (30°)
  = 288√3 cos (ωt + 30°) V
Therefore, the time-domain expressions for the three line-to-line voltages are νAB = 288[tex]\sqrt{3}[/tex] cos (ωt - 105°) V, νBC = 288[tex]\sqrt{3}[/tex] cos (ωt - 120°) V, and νCA = 288[tex]\sqrt{3}[/tex] cos (ωt + 30°) V.

To learn more about voltages
https://brainly.com/question/30741034
#SPJ4

Complete Question:
The time-domain expressions for three line-to neutral voltages at the terminals of a Y-connected load are νAN = 288 cos (ωt - 45°) V, νBN = 288 cos (ωt - 165°) V, νCN = 288 cos (ωt + 75°) V. What are the time-domain expressions for the three line-to-line voltages νAB, νBC, and νCA?

A girl and a boy are riding on a merry-go-round that is turning at a constant rate. The girl is near the outer edge, and the boy is closer to the center. Who has greater linear speed?
A. the boy
B. both have zero speed
C. the girl has greater linear speed
D. both the girl and the boy have non zero linear speed

Answers

C. The girl has greater linear speed.

The merry-go-round is turning at a constant rate, which means the angular velocity (ω) of the girl and the boy is the same. However, since the girl is nearer to the outer edge of the merry-go-round, she has to travel a greater distance along the circumference of the circle than the boy does in the same amount of time. Therefore, the girl has a greater linear speed than the boy.

Linear speed, also known as tangential speed, is the rate at which an object travels along a straight line path. It is the magnitude of the velocity vector of an object in uniform circular motion.

The formula for linear speed is:

v = rω

where v is the linear speed, r is the radius of the circle, and ω (omega) is the angular velocity, or the rate at which the object is rotating.

Linear speed is measured in units of distance per unit time, such as meters per second (m/s) or kilometers per hour (km/h).

In the case of the merry-go-round, the girl, who is closer to the outer edge of the circle, travels a greater distance in the same amount of time than the boy, who is closer to the center. Therefore, the girl has a greater linear speed than the boy.

Linear speed is an important concept in physics, especially in the study of circular motion and the motion of rotating objects. It is also used in many practical applications, such as determining the speed of vehicles, machinery, and other moving objects.

To know more about linear speed, please click on:

https://brainly.com/question/13100116

#SPJ11

The typical density and temperature of molecular clouds are:.

Answers

Molecular clouds are interstellar clouds composed of molecules, primarily hydrogen (H2) and helium (He). They are typically dense (typically 10-100 cm-3) and cold (typically 10-20 K), with temperatures often below the freezing point of water.

This low temperature is due to the low thermal energy of the molecules and the lack of radiative processes in the interstellar medium. The density and temperature of a molecular cloud are determined by the balance between the gravitational pull of the cloud and the pressure from the surrounding interstellar medium.

The density is also affected by the presence of star formation, which can dramatically increase the local pressure and temperature.

The presence of turbulent motions, shocks, and magnetic fields also affect the density and temperature of the cloud.

Know more about Thermal energy  here

https://brainly.com/question/18989562#

#SPJ11

in a simplified model of the hydrogen atom, its electron moves in a circular orbit with a radius of 5.3 * 10-10 m at a frequency of 6.6 * 1015 hz. what magnetic field would be required to cause an electron to undergo this same motion?

Answers

The magnetic field of [tex]1.16 * 10^{-4}[/tex] Tesla would be required to cause an electron to undergo the same circular motion as in the simplified model of the hydrogen atom.

This can be determined using the equation for the magnetic field required for a charged particle to move in a circular path, which is B = (mv)/qR, where B is the magnetic field, m is the mass of the electron, v is its velocity, q is its charge, and R is the radius of the circular orbit.

Substituting the given values into this equation, we get

[tex]B = (9.11 * 10^{-31}  kg * 2 * pi * 5.3 * 10^{-10}  m * 6.6 * 10^{15} Hz)/(1.6 * 10^{-19}C)[/tex]

= [tex]1.16 * 10^{-4}[/tex]
Therefore, a magnetic field of [tex]1.16 * 10^{-4}[/tex] Tesla would be required to cause an electron to undergo the same circular motion as in the simplified model of the hydrogen atom.

For more information on magnetic field kindly visit to

https://brainly.com/question/15581823

#SPJ11

TRUE or FALSE:
In order for John to hear Jill, air molecules must move from the lips of Jill to the ears of John.

Answers

In order for John to hear Jill, air molecules must move from the lips of Jill to the ears of John is true.

Define sound

A vibration known as sound travels through a transmission medium like a gas, liquid, or solid as an acoustic wave. Sound is the reception of these waves and the brain's perception of them in terms of human physiology and psychology.

The adjacent medium particles experience pressure changes as an object vibrates. The entire sound wave is made up of these compression and rarefaction zones. And this is how sound waves go through the space or through any other medium.

To learn more about sound :

https://brainly.com/question/16093793

#SPJ4

Potential energy is the energy an object has because of its __________.a. Temperatureb. Densityc. Positiond. Velocity

Answers

Potential energy is the energy an object has due to its position or arrangement within a system, and it can be transformed into other energy types like kinetic energy. It increases with height in a gravitational field.

Potential energy is the power a thing possesses as a result of its placement or arrangement within a system. It is a type of energy that is held and may be released or changed into other energy types, such kinetic energy, which is the energy of motion.The location of an object in a gravitational field immediately affects that object's potential energy. The potential energy of an item increases with height above a reference point. A book on a shelf, for instance, contains potential energy since it might fall to the ground owing to gravity. The book has greater potential energy if it is placed on a higher shelf since it is farther away from the ground.

learn more about Potential energy here :

https://brainly.com/question/24284560

#SPJ11

A 2.00 m long string has a mass of 7.50 g. A 40 g mass is attached to the string and hung over a pulley (see illustration from one of the team problems). The end of the string is then vibrated at a frequency of 130 Hz. Find the wavelength for the wave generated. Give your answer in centimeters (cm) and with 3 significant figures.

Answers

The wavelength of the wave generated is 0.323 cm with 3 significant figures.

What is wavelength?

Wavelength is a measure of the distance between two successive points of a wave, or the length of a single cycle of a wave. It is usually measured in meters (m). Wavelength is an important property of any wave, as it determines the frequency and amplitude of the wave. Wavelength is inversely proportional to frequency, meaning that as frequency increases, wavelength decreases.

λ = (T/μ) x (1/f)
where λ is the wavelength,
T is the tension of the string,
μ is the mass of the string, and
f is the frequency.
Using the given information, we have:
T = 40 g
μ = 7.50 g
f = 130 Hz
Substituting these values into the equation, we get:
λ = (40/7.50) x (1/130)
Solving for λ, we get:
λ = 0.323 cm
Therefore, the wavelength of the wave generated is 0.323 cm with 3 significant figures.

To learn more about wavelength
https://brainly.com/question/10728818
#SPJ4

5.consider the following scenario: a pot of water containing a hot dog and a carrot of equal mass is brought to a boil. after 1 minute, you remove the two substances from the water and record their internal temperature. assuming they had the same initial temperature, would you expect them to have the same final temperature? explain the reasoning behind your prediction.

Answers

No, we would not expect the hot dog and carrot to have the same final temperature. This is because the specific heat capacity of the two substances is different. The specific heat capacity of water is much higher than that of a hot dog or a carrot.

During the heating process, the water transfers more heat energy to the carrot and hot dog due to their lower specific heat capacity. However, the hot dog and carrot do not absorb this heat energy equally due to their different masses and compositions.

Additionally, it's important to note that the rate of heat transfer during the boiling process may also affect the final temperature of the two substances.

For example, if the hot dog was closer to the bottom of the pot, it may have received more heat energy due to the hotter water at the bottom of the pot, resulting in a higher final temperature compared to the carrot.

To know more about specific heat capacity, refer here:

https://brainly.com/question/27991746#

#SPJ11

Two cars are traveling at the same constant speed v. Car a is moving along a straight section of the road, while b is rounding a circular turn. Which statement is true about the acceleration of the cars?.

Answers

Car A (on a straight path) is not accelerating since velocity remains constant (speed and direction)
Car B is in constant acceleration even though velocity value remains constant (speed) velocity is a vector quantity (meaning has direction) direction is constantly changing to remain on a circular path meaning velocity is constantly changing so is acceleration!

Hope this helps :)

What is the biggest benefit to scientists of using a computer model to study volcanic eruptions

Answers

Having the ability to mimic and research volcanic phenomena in a controlled setting is one of the main advantages of utilizing computer models to investigate volcanic eruptions.

While it may be challenging or impossible to do so in the real world, scientists can manipulate different parameters using computer models and see how changes in those factors alter the behaviour of the volcanic system.

Additionally, scientists can use computer models to test theories and generate predictions regarding volcanic activity that are challenging to confirm through simple direct observation. This could enhance our comprehension of the fundamental mechanisms that trigger volcanic eruptions and, in turn, result in more accurate hazard assessments and mitigation plans.

Overall, computer models are an effective tool for analyzing volcanic events, allowing researchers to carry out fictitious experiments, can improve our understanding of these intricate natural systems by testing hypotheses and making predictions.

To know more about computer models

https://brainly.com/question/17686573

#SPJ1

The speed of all electromagnetic waves is 3. 00 × 10^8 meters per second. What is the wavelength of an x-ray with a frequency of 1. 18 × 10^18 hz?.

Answers

The formula to find the wavelength of any electromagnetic wave is λ = c / f, where λ is the wavelength, c is the speed of light, and f is the frequency of the wave. Since x-rays are a type of electromagnetic wave, this formula can be applied to find the wavelength of an x-ray with a frequency of 1.18 × 10^18 Hz.

Substituting the given values into the formula, we get λ = (3.00 × 10^8 m/s) / (1.18 × 10^18 Hz). Simplifying this equation, we get λ = 2.54 × 10^-10 meters.

Therefore, the wavelength of an x-ray with a frequency of 1.18 × 10^18 Hz is 2.54 × 10^-10 meters. It's important to note that x-rays have a much shorter wavelength than visible light, which allows them to penetrate through dense materials and create detailed images of bones and organs in medical imaging.

To know more about electromagnetic wave visit:

https://brainly.com/question/3101711

#SPJ11

stop to think 10.8 a weight attached to a rope is released from rest. as the weight falls, picking up speed, the rope spins a generator that causes a light bulb to glow. define the system to be the weight and the earth. in this situation,

Answers

In this situation, the weight and the earth are the system, as they are the two objects that interact with each other.

The weight is falling due to the force of gravity exerted by the earth, and as it falls, it is also spinning a generator, which converts the kinetic energy of the weight into electrical energy that powers the light bulb. The earth, in turn, exerts an equal and opposite gravitational force on the weight, in accordance with Newton's third law. The energy transformation that takes place in this system involves the conversion of potential energy (due to the weight's position above the earth) into kinetic energy (as the weight falls) and then into electrical energy (as the generator is spun).

Learn more about “   electrical energy“ visit here;

https://brainly.com/question/13989137

#SPJ4

Calculate the angular momentum of a solid uniform sphere with a radius of 0.120m and a mass of 14.0kg if it is rotating at 6.00rad/s about an axis through its center.
Calculate kinetic energy of a solid uniform sphere with a radius of 0.120m and a mass of 14.0kg if it is rotating at 6.00rad/s about an axis through its center.

Answers

The angular momentum and kinetic energy of a solid uniform sphere rotating about an axis through its center can be calculated using the formulas L = Iω and [tex]$K = \frac{1}{2}I\omega^2$[/tex], respectively. The kinetic energy of the sphere is 5.4825 joules.

To calculate the angular momentum of a solid uniform sphere, we need to use the formula:

L = Iω

where L is the angular momentum, I is the moment of inertia, and ω is the angular velocity.

For a solid uniform sphere rotating about an axis through its center, the moment of inertia is given by:

[tex]$I = \frac{2}{5}mr^2$[/tex]

where m is the mass of the sphere and r is the radius.

Plugging in the given values, we get:

[tex]$I = \frac{2}{5}(14.0\ \text{kg})(0.120\ \text{m})^2 = 0.2419\ \text{kg}\cdot\text{m}^2$[/tex]

The angular momentum is then:

[tex]$L = I\omega = (0.2419\ \text{kg}\cdot\text{m}^2)(6.00\ \text{rad/s}) = 1.4514\ \text{kg}\cdot\text{m}^2/\text{s}$[/tex]

To calculate the kinetic energy of the sphere, we can use the formula:

[tex]$K = \frac{1}{2}I\omega^2$[/tex]

where K is the kinetic energy.

Plugging in the values we get:

[tex]$K = \frac{1}{2}(0.2419\ \text{kg}\cdot\text{m}^2)(6.00\ \text{rad/s})^2 = 5.4825\ \text{J}$[/tex]

Therefore, the kinetic energy of the sphere is 5.4825 joules.

It is worth noting that both angular momentum and kinetic energy are conserved quantities in the absence of external torques or forces. They are useful in understanding the motion and behavior of rotating bodies. In this case, the solid uniform sphere is rotating about an axis through its center, and the calculations show the values of its angular momentum and kinetic energy.

To learn more about angular momentum

https://brainly.com/question/29563080

#SPJ4

gas characteristics, magma volume, and eruption velocity of basaltic magma are the major controlling factors that determine:_______

Answers

The major controlling factors that determine the eruption style and intensity of basaltic magma are gas characteristics, magma volume, and eruption velocity.

Gas characteristics, such as the amount and types of dissolved gases (e.g., water vapor, carbon dioxide, sulfur dioxide) in magma, can influence the explosivity of an eruption. More dissolved gases often result in more explosive eruptions.

Magma volume plays a crucial role in determining the scale of an eruption, with larger volumes typically leading to more intense and longer-lasting events.

Lastly, eruption velocity, which refers to the speed at which magma is expelled from a volcanic vent, affects the type and range of volcanic products and hazards. In summary, these factors work together to control the eruption style and intensity of basaltic magma, shaping the resulting volcanic landscapes and associated hazards.

To know more about volcanic landscapes click on below link:

https://brainly.com/question/3520727#

#SPJ11

impulse: a 2.50-kg stone is dropped from rest at a height of 3.50 m. what impulse does gravity impart to this stone from the instant it is dropped until it hits the ground, assuming negligible air resistance?

Answers

According to the question the impulse imparted to the stone by gravity is 19.5 kg m/s.

What is gravity ?

Gravity is a natural phenomenon by which all physical bodies attract each other. It is most commonly experienced as the weight of objects towards the centre of the Earth. The force of gravity is the result of the mass of two objects and the distance between them. It is one of the four fundamental forces of nature, along with electromagnetism, the weak nuclear force and the strong nuclear force. Albert Einstein's General Theory of Relativity explains gravity as the curvature of spacetime caused by the presence of mass.

The impulse imparted to the stone by gravity can be calculated using the equation Impulse = Force x Time.
We can calculate the time using the equation t = √(2h/g), where h is the height of the drop (3.50 m) and g is the acceleration due to gravity (9.8 m/s²).
Plugging in the values, we get t = √(2(3.50)/9.8) = 0.788 s.
The impulse imparted to the stone by gravity is mgt = (2.50 kg)(9.8 m/s²)(0.788 s) = 19.5 kg m/s.

To learn more about gravity

https://brainly.com/question/940770

#SPJ4

If the force each person applies is vertical, what is the magnitude of the force applied by the person above? express your answer with the appropriate units.

Answers

According to the question the force applied by the person above is 1401.4 N.

What is force?

Force is a physical quantity that is a measure of the interaction between objects. It is a vector, which means it has both magnitude and direction. Force is an influence that can cause an object to accelerate, decelerate, change direction, or remain in its current state. It is the result of an interaction between two objects that either attracts or repels them. Examples of forces include gravity, friction, electromagnetic force, and the force of a muscle. Force is a fundamental concept in physics and is necessary for understanding the behavior of matter and its interactions with energy.

The magnitude of the force applied by the person above can be calculated using the equation F = mgsinθ, where m is the mass of the crate (200 kg), g is the acceleration due to gravity ([tex]9.8 m/s^2[/tex]), and θ is the angle of the stairs (45°).
Therefore, the force applied by the person above is
[tex](200 kg)(9.8 m/s^2)(sin45^\circ) = 1401.4 N.[/tex]

To learn more about force
https://brainly.com/question/12785175
#SPJ4

Complete Question:

a massless, frictionless pulley is mounted on frictionless bearings and supported by a stand of mass 4m at rest on a table as shown above. passing over the pulley is a massless cord supporting a block of mass m on the left and a block of mass 2m on the right. after the masses are released from rest, what normal force does the table exert to support the entire system

Answers

When the masses are released from rest, the block of mass m will accelerate downwards with a force of mg, where g is the acceleration due to gravity. This will cause the cord to move and the block of mass 2m will accelerate upwards with a force of 2mg. Since the pulley is massless and frictionless, the tension in the cord will be the same on both sides of the pulley.

The force exerted by the table on the stand can be found using Newton's third law of motion, which states that for every action, there is an equal and opposite reaction. Therefore, the normal force exerted by the table on the stand is equal in magnitude and opposite in direction to the weight of the entire system.

The weight of the system can be found by adding up the weights of all the components. The block of mass m has a weight of mg, the block of mass 2m has a weight of 2mg, and the stand has a weight of 4mg. Therefore, the total weight of the system is 7mg.

Therefore, the normal force exerted by the table on the stand is 7mg upwards.


To find the normal force that the table exerts to support the entire system, we'll consider the following terms: massless frictionless pulley, frictionless bearings, stand of mass 4m, massless cord, block of mass m, and block of mass 2m.

Step 1: Identify the forces acting on the system.
The entire system consists of the stand (4m) and the two blocks (m and 2m). The force acting on the system is gravity, pulling each mass downward. The total gravitational force is (4m + m + 2m) * g, where g is the acceleration due to gravity (9.81 m/s²).

Step 2: Calculate the total gravitational force.
Total gravitational force = (4m + m + 2m) * g = (7m) * g

Step 3: Determine the normal force exerted by the table.
The normal force is equal in magnitude and opposite in direction to the total gravitational force acting on the system. Since the system is at rest on the table, there is no net vertical force, meaning that the normal force must balance out the gravitational force.

Normal force = Total gravitational force = (7m) * g

So, the normal force exerted by the table to support the entire system is (7m) * g.

To know more about friction visit:

https://brainly.com/question/13000653

#SPJ11

two charged particles held close to each other are released. as they move, their speeds increase. therefore, their charges have

Answers

Release of two charged particles that were bound closely together. The force acting on each particle grows as they move. Therefore, the particles have Like Charges.

What is force?

Force is a physical quantity that is a measure of an object's interaction with other objects. It is a vector quantity, meaning it has both magnitude and direction, and it is typically denoted by the letter F. Force can be described as a push or a pull, and is the result of the interaction between two objects. Force can be caused by a variety of things, including gravity, friction, and electromagnetic fields, and can be used to describe motion, energy, and pressure. Force is an integral part of the study of physics and is used to explain the behavior of objects in a variety of physical situations.

To learn more about force
https://brainly.com/question/12970081
#SPJ4

Complete Question:
Two charged particles held close together are released. As they move, the force on each particle increases. Therefore, the particles have _____

Question 3 options:

A. Opposite Charges

B. Like Charges

C. No Charge

During the simple harmonic motion of a pendulum, where is the acceleration greatest?

Answers

During the simple harmonic motion of a pendulum, the acceleration is greatest at the lowest point in its swing, which is also called the equilibrium point or the bottom of the arc.

A pendulum exhibits simple harmonic motion when it swings back and forth repeatedly under the influence of gravity. As the pendulum swings, it moves from one extreme point (the highest point, called the amplitude) to the other (the lowest point, called the equilibrium point). At the equilibrium point, the velocity of the pendulum is momentarily zero, but the acceleration is at its maximum. This is because the force of gravity acting on the pendulum bob is at its maximum at the equilibrium point, which causes the pendulum to accelerate towards the lowest point in its swing. As the pendulum swings back towards the amplitude, the acceleration decreases, reaches zero at the amplitude, and then starts to increase again as the pendulum swings back towards the equilibrium point.

To know more about motion please visit:

https://brainly.com/question/22810476

#SPJ11

Other Questions
By 1850, which of these was the most efficient way to move goods in the north?. how do we calculate percent ionization in water? during the lead-up to the iraq war, antiwar activists used the same argument that they had used to protest the vietnam war in the 1960s and 1970s, that the united states was being a hostile aggressor. this is an example of: Social mobility refers to the degree to which _____.a.members from a collectivist society move to an individualist societyb.members from a lower social category move to a higher social categoryc.people from emerging economies move to developed economiesd.people from developed economies move to emerging economies downward comparisons may ________ in middle childhood How does "Subjective Pressure" come up with operating range? viewing online communication as a fantasy world instead of reality is a key component and driving force of internet trolling, called: From a surface measurement made by surface profilometer, the following point values were obtained. (The scale factor is 0.6 micrometer). There are 10 points. 516,534,518,533,518,530,520,526,521 and 526.Try to find Ra,Rq,Rt values and Ratio Ra/Rq. CHARACTER IDENTIFICATION: Match each of the following characters withhis/her best description.LuisRanoChicharron_ ClavoWiloA.B.C.D.E.Luis' best friend; he grows up to father a childand go to jail for accessory to murderone of "los quatro;" he moves away from Lomasand is shot and run over in another barriohe is shot in the face during a Sangra drive-by,then disappears from his group of friendsLuis' older brother who later changeshim name to just "Joe"Ramiro's father When president johnson vetoed a law that would extend the freedmens bureau, congress reacted by. Effect of consumption of chocolate is perhaps the most misrepresented news in traditional media outlets, with claims from "eating chocolate once every day decreases the risk of liver cancer" to "eating chocolate once every day increases the risk of liver cancer" and everything in between. However, statistical studies are much more focused and particular research questions and outcomes often go unnoticed in media.A group of researchers are interested in studying whether consumption of Belgian chocolate with 14gms of added sugar every day can be linked to increased palpitation in adults of ages 25-50. They performed a randomised trial concerning 10 adults over 2 days. They were given a normal breakfast on the first day, and on the second day, they were given chocolates with breakfast. Each day, their pulse rate was measured and the difference in pulse rates were recorded.Please use this setup for the next 4 questions.Let C be the change in the recorded pulse rates from eating the belgian chocolate. c = u after - u beforeState the null and alternative hypotheses for this study.State the null and alternative hypotheses for this study.Question 1 options:a)H0: The average pulse rate does not change after the consumption of chocolates (C = 0 beats / min)Ha: The average pulse rate is higher after the consumption of chocolate (C > 0 beats / min).b)H0: The average pulse rate does not change after the consumption of chocolates (C = 0 beats / min)Ha: The average pulse rate changed after the consumption of chocolate(0 beats/min).c)H0: The average pulse rate will increase after the consumption of chocolates (C > 0 beats / min)Ha: The average pulse rate decreased after the consumption of chocolate (C 0 beats / min).d)H0: The average pulse rate reduced after the consumption of chocolates (C < 0 beats / min)Ha: The average pulse rate is higher after the consumption of chocolate (C 0 beats / min).Question 2 (1 point)The change in heart rate for the 10 individuals are as follows(1.8, -0.4, -0.6, 0.4, 0.2, -1.0, 1.6, 0.8, 2.0, -2.0).Please calculate the mean change in heart rate and round to 2 decimal places. Question 6 of 10Which action would more likely take place in a modern family rather than in atraditional family?OA. A farmer works long hours in his fields to feed his large andgrowing family.OB. A woman is pressured to quit her job and stay home to care forher child.OC. A student decides to attend a college hundreds of miles fromhome.OD. A poor worker encourages his parents to move into his home afterthey retire. if codons were composed of only 2 nucleotides each, how many amino acids (out of the 20) would there not be a code for? this man was among the enterprising journalists who created the nation's first cheap, daily newspapers. Who is this man? How much should the distillation flask be filled? when you enter a description for the fields in your table, the descriptive text appears when you are adding records to a datasheet or form.T/F Consider following instruction sequenceBEQ R1, R2, GOTOMUL R3, R1, R2SW A 0 (R3)GOTO: SUB R5, R1, R4What is the issue if a machine runs the program with a pipeline (in parallel) and how can you resolve the issue? Please take care instructions. gas characteristics, magma volume, and eruption velocity of basaltic magma are the major controlling factors that determine:_______ Potential energy is the energy an object has because of its __________.a. Temperatureb. Densityc. Positiond. Velocity How does Shakespeare most develop the universal themes "the search for knowledge and "the tension between truth and illusion in these excerpts?through references to trust and betrayalthrough Macbeths internal conflictthrough Macbeths conflict with Banquothrough references to the supernatural