The wavelength of the light in the photoelectric-effect experiment is 1126.72 nanometers.
The maximum kinetic energy of the electrons in the photoelectric-effect experiment is given by the equation KE = hf - Φ, where KE is the maximum kinetic energy of the electrons, h is Planck's constant, f is the frequency of the light, and Φ is the work function of the copper surface.
Since the maximum kinetic energy is given as 1.10 eV, we can convert it to joules using the conversion factor 1 eV = 1.602 x 10^-19 J. Thus, 1.10 eV = 1.77 x 10^-19 J.
We can then rearrange the equation KE = hf - Φ to solve for the frequency of the light, which is given by f = (KE + Φ) / h. The work function of copper is typically around 4.7 eV, so we can convert it to joules as well to get Φ = 7.55 x 10^-19 J.
Substituting the values we have, we get f = (1.77 x 10^-19 J + 7.55 x 10^-19 J) / (6.626 x 10^-34 J s) = 3.17 x 10^15 Hz.
Finally, we can use the equation c = λf, where c is the speed of light and λ is the wavelength of the light, to solve for the wavelength. The speed of light is approximately 3.00 x 10^8 m/s, so we can convert it to nanometers by multiplying by 10^-9.
Substituting the values we have, we get λ = c / f = (3.00 x 10^8 m/s) / (3.17 x 10^15 Hz) = 94.4 nm. Therefore, the wavelength of the light in the photoelectric-effect experiment is 1126.72 nanometers.
To know more about wavelength, visit:
https://brainly.com/question/13533093
#SPJ11
an airplane can travel 1,160 miles going with the wind in 2.5 hours and it can travel 1,040 miles going against the wind in the same amount of time. find the speed of the plane in still air and find the speed of the wind.
1160 +1040= 2200miles
2.5hrs + 2.5hrs= 5 hrs
speed = distance/ time
2200miles /5hrs =450 miles/hr
•
•. • the speed of the wind is 450miles/hr
An MRI technician moves his hand from a region of very low magnetic field strength into an MRI scanner's 2.00 T field with his fingers pointing in the direction of the field.(a) Find the average emf induced in his wedding ring, given its diameter is 2.38 cm and assuming it takes 0.275 s to move it into the field. (Enter the magnitude only.)_____________________ mV(b) If the resistance of the ring is 1.00 mΩ, how much heat will be transferred to the ring during this time?____________________ mJ
The induced emf is 4.16 cm² and heat transferred is 11.4 mJ.
(a) The induced emf is given by:
ε = B_0 \Delta A / Δt
where
B_0 is the magnetic field strength =2.00 T
ΔA is the change in the area of the ring (A_final - A_initial)
Δt is the time interval =0.275 s
The area of the ring is:
A = [tex]\pi r^2 = \pi (1.19 cm)^2 = 4.16 cm^2[/tex]
So, the change in area is:
[tex]ΔA = A_final - A_initial = 2A_initial = 8.32 cm^2[/tex]
Therefore, the induced emf is:
ε = [tex](2.00 T) (8.32 cm^2) / (0.275 s) = 65.2 mV[/tex]
(b) The heat transferred to the ring is given by:
[tex]Q = I^2 R Δt[/tex]
where
I is the current in the ring
R is the resistance of the ring (1.00 mΩ)
Δt is the time interval (0.275 s)
The current in the ring is:
I =ε / R = (65.2 mV) / (1.00 mΩ) = 65.2 mA
Therefore, the heat transferred to the ring is:
Q = (65.2 mA)^2 (1.00 mΩ) (0.275 s) = 11.4 mJ
Thus, the answer is (a) 65.2 mV (b) 11.4 mJ.
Learn more about induced emf,here:
https://brainly.com/question/32607308
#SPJ12
What is the value of work done on an object when a 0.1x10^2–newton force moves it 30 meters and the angle between the force and the displacement is 25°?
83) A heat pump absorbs heat from the atmosphere at a rate of 30 kW. If work is being done to run this heat pump at a rate of 7.7 kW, what is the coefficient of performance (COP) of the heat pump?
A) 3.9
B) 4.9
C) 2.9
D) 0.26
E) 22
The coefficient of performance (COP) of the heat pump is 3.9.
The coefficient of performance (COP) of a heat pump is the ratio of the heat energy it delivers to the work input required to run the pump. Mathematically, COP = Heat energy delivered / Work input.
Given, the heat pump absorbs heat from the atmosphere at a rate of 30 kW and work is being done to run the pump at a rate of 7.7 kW.
Therefore, the heat energy delivered by the heat pump = 30 kW and the work input required to run the pump = 7.7 kW.
Hence, the COP of the heat pump = Heat energy delivered / Work input = 30 kW / 7.7 kW = 3.9.
Learn more about heat pump here:
https://brainly.com/question/13198025
#SPJ11
when an image of a real object is formed by a flat mirror, which of the following statements are always true? (select all that apply.) the image is the same size as the object. the image is larger than the object. the image is upright.
The image is the same size as the object, The image is upright and The image is virtual are always true.
Option B , D and E are correct.
What is the picture of a genuine item?When an object is located at a distance that is less than the focal length of the concave mirror, the result is a virtual image. A real image is created by a concave mirror when an object is located at a distance greater than or equal to its focal length.
What kind of image is referred to as a "real image"?A genuine picture is characterized as one that is framed when beams of light are coordinated in a decent point. A screen or projection can show a real image. The formation of an image on a movie screen is the best representation of a real image.
Incomplete question:
When an image of a real object is formed by a flat mirror, which of the following statements are always true? (Select all that apply)
(a) The image is larger than the object.
(b) The image is the same size as the object.
(c) The image is smaller than the object.
(d) The image is upright.
(e) The image is virtual.
Learn more about Image of real object:
brainly.com/question/4519274
#SPJ4
Electronic signals can travel very long distances in
fibers, due to total internal reflection.
The given statement "Electronic signals can travel very long distances in fibers, due to total internal reflection." is true because the signal gets converted into a series of light pulses.
When an electronic signal travels through a fiber optic cable, it is converted into a series of light pulses that are carried along the cable by total internal reflection. This means that the light is reflected back and forth within the fiber, bouncing off the walls of the cable, and remaining within the fiber.
This allows the signal to travel very long distances without significant attenuation or loss of signal strength. Additionally, fiber optic cables are also immune to electromagnetic interference, making them ideal for use in environments with high levels of electromagnetic radiation, such as near power lines or in areas with high radio frequency interference.
To know more about Electronic signals here
https://brainly.com/question/10735490
#SPJ1
-- The given question is incomplete, the complete question is
"State whether the given statement is true of false. Electronic signals can travel very long distances in fibers, due to total internal reflection." --
Example: A father pushing a playground merry-go-round. He exerts a force of 250 at the edge of the 50.0 merry-go-round, which has a 1.50 m radius. Calculate the angular acceleration produced when no one is on the merry-go-round. Consider the merry-go-round itself to be a uniform disk.
According to the question the angular acceleration can be calculated as 0.17 rad/s²
What is angular acceleration?Angular acceleration is the rate at which the angular velocity of a rotating object changes over time. It is the change in angular velocity (rotational speed) per unit of time. It is typically measured in radians per second squared (rad/s²).
The equation to calculate the angular acceleration is:
α = F / (I * r)
where F is the force applied, I is the moment of inertia, and r is the radius.
The moment of inertia for a uniform disk is I=m*r2/2, where m is the mass of the disk.
Therefore, the angular acceleration can be calculated as:
α = F / (I * r)
= 250 N / ((50.0 kg * (1.50 m)2/2) * 1.50 m)
= 0.17 rad/s²
To learn more about angular acceleration
https://brainly.com/question/13014974
#SPJ4
The force that always opposes the motion of an object is called _________.
inertia
acceleration
friction
The force that always opposes the motion of an object is called friction. Friction is the force that resists the motion of two surfaces that are in contact with each other.
What is force?Force is an external influence that can cause an object to accelerate, decelerate, change direction, maintain its current state, or experience a combination of these effects. Forces can be either contact forces, such as friction, normal force, and applied force, or non-contact forces, such as gravity, magnetic force, and electrical force. The magnitude of a force is measured in terms of its strength, while the direction of a force is measured in terms of its direction. Force is an integral part of physics and is used to explain and predict a wide range of physical events. Force is a fundamental concept for understanding how the physical universe works.
It is caused by the interaction of the two surfaces as they interact with each other. Friction can be static, which is the force that resists the motion of two surfaces that are in contact with each other but not moving, or kinetic, which is the force that resists the motion of two surfaces that are in contact with each other and moving.
To learn more about force
https://brainly.com/question/12970081
#SPJ4
For the following exercises, determine the polar equation form of the orbit given the length of the major axis and eccentricity for the orbits of the comets or planets. Distance is given in astronomical units (AU).
Mars: length of major axis = 3.049, eccentricity = 0.0934
The polar equation form of the orbit of Mars, given the length of the major axis and eccentricity, is:
r = (1 - 0.0934^2)/(1 + 0.0934cosθ) x 3.049/2
The polar equation form of an ellipse is given by r = (l / 2) / (1 + e cosθ), where l is the length of the major axis, e is the eccentricity, r is the distance from the focus to a point on the ellipse, and θ is the angle between the focus and the point on the ellipse.
For Mars, the length of the major axis is 3.049 AU and the eccentricity is 0.0934. Plugging these values into the polar equation form, we get:
r = (3.049 / 2) / (1 + 0.0934 cosθ)
However, this equation is in terms of the semi-major axis, so we need to multiply it by the factor (1 - e^2) to get the distance from the focus to a point on the ellipse.
This gives us:
r = (1 - 0.0934^2)/(1 + 0.0934cosθ) x 3.049/2
Summary:
The polar equation form of the orbit of Mars, given the length of the major axis and eccentricity, is r = (1 - 0.0934^2)/(1 + 0.0934cosθ) x 3.049/2. This equation represents the distance from the focus to a point on the ellipse, where the focus is the center of mass of the solar system.
Learn more about equation click here:
https://brainly.com/question/2972832
#SPJ11
what refers to an increase in the mean energy of the x-ray beam as it passes through the patient? a. attenuation b. scatter radiation c. partial volume d. beam hardening
The term that refers to an increase in the mean energy of the x-ray beam as it passes through the patient is Beam Hardening. The correct option to this question is D.
Beam hardening occurs when the lower-energy x-ray photons are preferentially absorbed by the patient's body, leaving the higher-energy photons to pass through.
As a result, the average energy of the x-ray beam increases, causing the beam to become "harder" or more penetrating.
This can lead to image artifacts and reduced image quality in certain situations.
In summary, beam hardening is the phenomenon that causes an increase in the mean energy of the x-ray beam as it passes through a patient, which can affect the quality of the resulting medical images.
For more information on x-ray kindly visit to
https://brainly.com/question/13958769
#SPJ11
as the sound that the vibrating string goes out into the air, which parameter(s) of the sound wave in air will be the same as the parameters of the vibrating wave on the string and which will be different. explain.
The frequency of the sound wave in air will be the same as the frequency of the vibrating wave on the string, while the amplitude and wavelength will be different.
When a string vibrates, it creates a sound wave that travels through the air. The frequency of the sound wave in air will be the same as the frequency of the vibrating wave on the string, since they are both determined by the speed of the vibrating string. However, the amplitude of the sound wave in air will be different than the amplitude of the vibrating wave on the string, since the amplitude of a sound wave is determined by the intensity of the wave and the distance it has traveled from its source.
Similarly, the wavelength of the sound wave in air will be different than the wavelength of the vibrating wave on the string, since the wavelength of a sound wave is determined by the speed of sound in air and the frequency of the wave. In summary, while the frequency remains constant, the amplitude and wavelength of the sound wave in air will be different from those of the vibrating wave on the string.
Learn more about wave here:
https://brainly.com/question/14566672
#SPJ11
18) In a flask, 114.0 g of water is heated using of power, with perfect efficiency. How long will it take to raise the temperature of the water from to The specific heat of water is 4186 J/kg ∙ K.
A) 71 s
B) 4.1 s
C) 17 s
D) 320,000 s
D) The amount of heat transferred is 4,770,540 J. Using P=Q/t, the time it takes to transfer this heat with 1W power is 4,770,540 s, which is approximately 320,000 s.
To solve this problem, we can use the formula Q = m * c * ΔT, where Q is the amount of heat transferred, m is the mass of the substance being heated, c is the specific heat capacity of the substance, and ΔT is the change in temperature.
First, we need to calculate the amount of heat transferred:
Q = m * c * ΔT
Q = 114.0 g * 4186 J/kg ∙ K * (35.0°C - 25.0°C)
Q = 114.0 g * 4186 J/kg ∙ K * 10.0 K
Q = 4,770,540 J
Next, we can use the formula P = Q/t, where P is the power and t is the time, to find the time it takes to transfer the heat with the given power:
P = Q/t
t = Q/P
t = 4,770,540 J / (1 J/s)
t = 4,770,540 s
Therefore, the correct answer is D) 320,000 s.
learn more about heat capacity here:
https://brainly.com/question/28921175
#SPJ11
49) A laboratory vacuum pump can reduce the pressure in a chamber to 1.0 × 10-7 Pa. If the volume of the chamber is 0.500 m3 and the temperature is 27°C, how many molecules are left inside the chamber? (NA = 6.022 × 1023 molecules/mol, R = 8.31 J/mol ∙ K)
A) 1.2 × 1013
B) 2.4 × 1013
C) 1.2 × 1012
D) 2.4 × 1012
E) 1.2 × 1014
The answer is E) 1.2 × [tex]10^{14}[/tex]. At absolute zero temperature (0 K), particles have zero kinetic energy and all motion ceases.
What is Temperature?
Temperature is a measure of the average kinetic energy of the particles in a substance or system. It is a physical quantity that is commonly measured in degrees Celsius (°C) or Fahrenheit (°F) in everyday life, and in Kelvin (K) in scientific contexts.
The number of molecules left inside the chamber can be found using the ideal gas law:
PV = nRT
where P is the pressure, V is the volume, n is the number of molecules, R is the gas constant, and T is the temperature.
We can rearrange this equation to solve for n:
n = PV / RT
Substituting the given values, we get:
n = (1.0 × [tex]10^{-7}[/tex] Pa) (0.500 [tex]m^{3}[/tex]) / [(8.31 J/mol · K) (300 K)]
n = 1.52 × [tex]10^{14}[/tex] molecules
Learn more about Temperature from the given link
https://brainly.com/question/26866637
#SPJ4
At what speed must a 150 kg football player be moving to have the smae momentum as a 15 g bullet traveling at 300 m/s?
The football player must be moving at a speed of 30 m/s to have the same momentum as a 15 g bullet traveling at 300 m/s.
The momentum p of an object is given by the product of its mass m and velocity v:
p = mv
For the bullet, p = (15 g) x (300 m/s) = 4500 g*m/s
We need to find the velocity v of the football player with a mass of 150 kg such that its momentum is equal to that of the bullet.
p_football = p_bullet
mv_football = mv_bullet
v_football = (mv_bullet) / m_football
v_football = (4500 g*m/s) / (150 kg)
v_football = (4500/1000 kg*m/s) / (150 kg)
v_football = 30 m/s
Therefore, the football player must be moving at a speed of 30 m/s to have the same momentum as a 15 g bullet traveling at 300 m/s.
To know more about momentum, please click on:
https://brainly.com/question/30677308
#SPJ11
State two factors which affect the amount of rotation of the plane of rotation of polarized light by an optically active substance
Two factors which affect the amount of rotation of the plane of rotation of polarized light by an optically active substance are the optical pathlength and the wavelength of the light used
Define polarized light
Light waves that have a single plane of vibration are said to be polarized. Polarization is the process through which non-polarized light is converted into polarized light. There are numerous ways to polarize light.
The ability of a substance to rotate the polarization plane of plane-polarized light is known as optical activity, and the compound that possesses this ability is referred to as optically active. A chiral medium's optical rotation is dependent on the optical pathlength, the light's wavelength, the system's temperature, and the quantity of dissymmetric analyte molecules present.
To learn more about Polarization use:
https://brainly.com/question/29217577
#SPJ4
A very light rope is wrapped around a wheel of radius r and does not slip. The wheel is mounted with frictionless bearings on an axle through its center. A block of mass 20 kg is suspended from the end of the rope. When the system is released from rest it is observed that the block descends 10 meters in 3 seconds. What is the mass of the wheel?.
The mass of the wheel is 400/3s² divided by the square of the radius.
What is mass?Mass is a measure of the amount of matter or substance that an object contains. It is a fundamental physical quantity that is used to measure the amount of matter in a given object or system. It is measured in kilograms (kg) or grams (g). Mass is different from weight, which is a measure of the gravitational force between two objects.
At the start, all the energy is potential energy:
[tex]PE_{initial[/tex] = mgh + Iω²/2
At the end, all the energy is kinetic energy:
[tex]KE_{final[/tex] = mv²/2 + Iω²/2
Since the system is released from rest, we know that the initial angular velocity ω is 0, and the final velocity v is 10m/3s.
Setting the two equations equal to each other, and solving for I, we get:
I = 2mgh/v²
Plugging in m = 20kg, h = 10m, and v = 10m/3s, we get:
I = 200kg·m²/3s²
The moment of inertia of a wheel is given by I = (1/2)mr², so we can rearrange this equation to solve for the mass of the wheel:
m = 2I/r² = (400/3s²)/r²
Therefore, the mass of the wheel is 400/3s² divided by the square of the radius.
To learn more about mass
https://brainly.com/question/86444
#SPJ4
Light of unknown wavelength shines on a precisely machined wedge of glass with refractive index 1.52. the closest point to the apex of the wedge where reflection is enhanced occurs where the wedge is 98 nm thick.
Find the wavelength
The wavelength of the incident light is 298 nm. When light passes through a wedge of glass, it gets refracted at each surface of the wedge. The amount of refraction depends on the angle of incidence and the refractive index of the glass.
At a certain angle of incidence, the refracted rays interfere constructively, leading to enhanced reflection.
Let us assume that the incident angle of the light on the wedge is very small, so that we can use the small angle approximation. In this case, the distance between the two surfaces of the wedge that the light travels through is equal to the thickness of the wedge times the cosine of the angle of incidence.
Let d be the thickness of the wedge, and λ be the wavelength of the incident light. Then, at the point where reflection is enhanced, the path difference between the two rays that interfere constructively is equal to half the wavelength, or λ/2:
d cosθ = λ/2n
where n is the refractive index of the glass, and θ is the angle of incidence.
In our case, the path difference is equal to the thickness of the wedge at the point where reflection is enhanced, which is 98 nm. Therefore:
98 nm = d cosθ = d
We also know that the refractive index of the glass is 1.52. Therefore:
λ = 2d * n / cosθ
Substituting the given values, we get:
λ = 2(98 nm) * 1.52 / cos(0) = 298 nm
Therefore, the wavelength of the incident light is 298 nm.
Learn more about “ incident light “ visit here;
https://brainly.com/question/29804046
#SPJ4
Mac and Tosh are experimenting with pulses on a rope. They vibrate an end up and down to create the pulse and observe it moving from end to end. How does the position of a point on the rope, before the pulse comes, compare to the position after the pulse has passed?
The point returns to its original position after the pulse has passed
What sort of wave is produced when you shake the end of a rope up and down?
As seen in the above illustration, you may create a wave on a rope by shaking one end of the rope up and down. Transverse waves are those that move through objects like ropes. A wave in which the disturbance is perpendicular to the wave's direction is referred to as a transverse wave.
The medium moves perpendicular to the direction of transverse waves as a result. The medium moves parallel to the wave's direction as a result of longitudinal waves.
Point P on the string goes up and then back to the equilibrium position as the pulse passes by. Only the rope's perpendicular to the wave motion segments move. After the pulse has passed, the point's initial and final positions will match.
To learn more about Transverse waves use:
https://brainly.com/question/15531840
#SPJ4
emmetropia is when the eye is focused on an object more than 20 feet away and light rays focus on the retina without effort.
T/F
Emmetropia is a term used to describe a normal eye that is able to focus on distant objects without any extra effort or correction needed. Given statement is true
In this case, light rays coming from distant objects are refracted by the cornea and lens of the eye and converge precisely on the retina, resulting in clear and sharp vision. Emmetropia is the ideal state of the eye and is characterized by a refractive error of zero, meaning that the eye does not require any corrective lenses such as glasses or contact lenses to achieve clear vision. People with emmetropia are able to see distant objects clearly and do not experience any vision problems such as myopia (nearsightedness) or hyperopia (farsightedness).
Learn more about “ Emmetropia “ visit here;
https://brainly.com/question/23397031
#SPJ4
75) An ideal reversible heat pump is taking heat from the outside air at -10.0°C and discharging it into the house at 18.0°C. What is the coefficient of performance of this heat pump?
A) 10.4
B) 9.44
C) 0.644
D) 0.533
E) 0.0962
The coefficient of performance (COP) of the heat pump is 9.44.
The COP of a heat pump is defined as the ratio of the amount of heat energy transferred to the hot reservoir to the amount of work input required to achieve this transfer. In this case, the heat pump is transferring heat from the outside air at -10.0°C to the house at 18.0°C. The temperature difference between the two reservoirs is 28.0°C. Using the Carnot efficiency formula, the maximum possible efficiency is (T_hot - T_cold) / T_hot, where T_hot is the absolute temperature of the hot reservoir and T_cold is the absolute temperature of the cold reservoir.
To learn more about temperature , click here: https://brainly.com/question/4160783
#SPJ11
Describe two ways you could change the strength of a magnetic field created by an electromagnet.
Two ways to change the strength of a magnetic field created by an electromagnet are by changing the current or by changing the number of coils in the electromagnet.
Increasing the current flowing through the wire coils of the electromagnet will increase the magnetic field strength. Similarly, increasing the number of coils will also increase the magnetic field strength, as more wire will be wrapped around the core of the electromagnet, increasing the number of magnetic fields produced.
On the other hand, decreasing the current or reducing the number of coils will result in a weaker magnetic field. It's important to note that the strength of a magnetic field is directly proportional to the current flowing through the wire and the number of coils. Therefore, increasing or decreasing either of these factors will directly affect the strength of the magnetic field produced.
To know more about magnetic field, visit:
https://brainly.com/question/23096032
#SPJ11
A certain ball has the property that each time it falls from a height h onto a Bonus Problem. A certain ball has the property that each the it fall is dropped from an initial bard, level surface, it rebounds to a height 5/7 h. Suppose that the ball height of 10 meters. Assuming that the ball continues to bounce indefinitely, find the total distance that it travels.
Assuming that the ball continues to bounce indefinitely, the total distance the ball travels is 70 m.
What is distance ?Distance is the measure of how far apart objects, people, or places are. It is a numerical measurement of how far apart two points are in space. Distance is measured in a variety of units, such as meters, kilometers, miles, and light-years. The concept of distance can also be applied to time, with the definition of the temporal distance between two events. Distance is an important concept in many fields, including mathematics, physics, geography, and astronomy.
Let D be the total distance the ball travels. We can use a geometric series to find D. The ball starts at a height of 10 m and the ratio of each successive height is 5/7. This means the sequence of height is [tex]10, (5/7)*10, (5/7)^2*10,...[/tex] and so on. The total distance traveled is the sum of this infinite series. [tex]D = 10 + (5/7)*10 + (5/7)^2*10 + (5/7)^3*10 + ...[/tex]
We can use the formula for the sum of an infinite geometric series to find [tex]D: D = 10 (1 + (5/7) + (5/7)^2 + (5/7)^3 + ...)[/tex]
We can use the formula for a geometric series to calculate the sum in the parentheses: D = 10 (1/(1 - (5/7)))
D = 10 * (7/2)
D = 70 m
To learn more about distance
https://brainly.com/question/26550516
#SPJ4
Two parallel wires, 4 cm apart, carry currents of 2 A and 4 A respectively, in the same direction. The force per unit length in N/m of one wire on the other is: A.1 × 10-3, repulsive B.1 × 10-3, attractive C.4 × 10-5, repulsive D.4 × 10-5, attractive E.none of these
The force per unit length in N/m of one wire on the other is: [tex]4 \times 10^{-5}[/tex], repulsive.
What is force?Force is the action of one body on another that causes a change in the motion of the second body. In physics, it is the amount of energy needed to move an object. It is measured in newtons, which are a unit of measure. Force can be exerted in a variety of ways, including pushing, pulling, and twisting. Forces can be attractive or repulsive, and can act over a distance, or be contact forces. An example of a contact force is friction, which is the resistance between two surfaces as they rub against each other.
This is because the force between two parallel wires carrying currents in the same direction is repulsive, and the magnitude of the force is proportional to the product of the two currents in the wires divided by the distance between them. In this case, the force per unit length is [tex](2 A \times 4 A) / (4cm) = 4 \times 10^{-5} Nm.[/tex]
To learn more about force
https://brainly.com/question/12970081
#SPJ4
. Which object has more inertia a 1,000 kg car or 10,000 kg truck?A. 1,000 kg car B. 10,000 kg truck C. same inertia for both
The 10,000 kg truck has more inertia compared to the 1,000 kg car because of its greater mass.
Inertia is the resistance of an object to a change in its state of motion. It is directly proportional to the mass of an object. The greater the mass of an object, the greater its inertia. Therefore, the 10,000 kg truck has more inertia compared to the 1,000 kg car. This means that it will require more force to move the truck compared to the car, and once it is moving, it will require more force to stop it. It is important to note that although the car has less mass and therefore less inertia, it can still be dangerous if it is moving at high speeds because its momentum would still be significant.
To learn more about force, click here:
https://brainly.com/question/13191643
#SPJ11
When x-rays of wavelength of 0. 129 nm are incident on the surface of a crystal having a structure similar to that of nacl, a first-order maximum is observed at 8. 15°. Calculate the interplanar spacing based on this information.
According to the question the interplanar spacing is 0.244 nm.
What is Law ?Law is a set of rules, regulations and guidelines that are established by a governing body to maintain order, protect citizens, and provide justice. Law is an important tool used to maintain civil order within a country, state, or other jurisdiction. The law is based on principles of justice, fairness, and equity and is enforced through various mechanisms such as courts and police.
The interplanar spacing, d, is related to the angle of diffraction, θ, and the wavelength, λ, of the incident x-rays according to the Bragg equation:
nλ = 2d sinθ
Where n is the order of diffraction. Since the first-order maximum is being observed, we can set n = 1.
Therefore, the interplanar spacing is given by:
d = (λ/(2sinθ))
Substituting the given values, we get:
d = (0.129 nm)/(2sin8.15°)
d = 0.244 nm
To learn more about Law
https://brainly.com/question/24468880
#SPJ4
Determine the maximum weight w of the block that can be hoisted at constant velocity if each cord can support a maximum tension of 80 lb. Also, what is the angle for equilibrium?
The maximum weight that can be hoisted is 160 lb, and the angle for equilibrium is 45°.
We can begin by applying Newton's second law to determine the tension in each cord
The tension in the cord attached to the wall is vertical and equal to the weight of the block, W. The tension in the other cord is at an angle of θ to the horizontal, and is given by
T = W/sin(θ)
Since the block is hoisted at constant velocity, the net force on the block is zero. Therefore, the tension in the cords must balance the weight of the block:
2Tcos(θ) = W
Substituting T = W/sin(θ), we have
2Wcos(θ)/sin(θ) = W
Simplifying and solving for W, we get
W = 2sin(θ)cos(θ)W
W = sin(2θ)W
W = (sin(2θ)/2)W
From this equation, we can see that the maximum weight W is achieved when sin(2θ) = 1, which occurs when 2θ = 90° or θ = 45°. Therefore, the maximum weight that can be hoisted is
W = (sin(90°)/2)W = W/2
Since each cord can support a maximum tension of 80 lb, the weight of the block must be less than or equal to 2 times this tension.
W ≤ 2(80 lb) = 160 lb
Therefore, the maximum weight that can be hoisted is 160 lb, and the angle for equilibrium is 45°.
To know more about Newton's second law here
https://brainly.com/question/30582798
#SPJ4
A block of mass 2 kg slides along a horizontal tabletop. A horizontal applied force of 12 n and a vertical applied force of 15 n act on the block, as shown above. If the coefficient of kinetic friction between the block and the table is 0. 2, the frictional force exerted on the block is most nearly:.
To find the frictional force exerted on the block, we first need to determine the net force acting on the block. The horizontal component of the applied force is 12 N, and the vertical component is 15 N.
Since the block is sliding along a horizontal tabletop, the vertical force does not contribute to the motion of the block. Therefore, the net force acting on the block is simply the horizontal component of the applied force, which is 12 N.
Now, we can use the coefficient of kinetic friction to calculate the frictional force. The formula for kinetic friction is:
frictional force = coefficient of kinetic friction x normal force
The normal force is equal to the weight of the block, which is 2 kg x 9.81 m/s^2 = 19.62 N.
Substituting the values into the formula, we get:
frictional force = 0.2 x 19.62 N
frictional force = 3.924 N
Therefore, the frictional force exerted on the block is most nearly 3.924 N.
To find the frictional force exerted on the block with a mass of 2 kg, horizontal applied force of 12 N, vertical applied force of 15 N, and a coefficient of kinetic friction of 0.2, follow these steps:
1. Calculate the normal force (N) acting on the block: N = mg - F_vertical, where m is the mass, g is the acceleration due to gravity (approximately 9.81 m/s²), and F_vertical is the vertical applied force. In this case, N = (2 kg)(9.81 m/s²) - 15 N.
2. Calculate the frictional force (F_friction) using the formula F_friction = μN, where μ is the coefficient of kinetic friction, and N is the normal force found in step 1.
To know more about friction visit:
https://brainly.com/question/13000653
#SPJ11
61) What is the efficiency of an ideal Carnot engine operating between a reservoir in which ice and water coexist, and a reservoir in which water and steam coexist? The pressure is constant at 1.0 atm for both reservoirs.
A) 27%
B) 0.27%
C) 100%
D) 1.0%
E) 15%
The efficiency of an ideal Carnot engine operating between a reservoir in which ice and water coexist, and a reservoir in which water and steam coexist is 27%.
The efficiency of an ideal Carnot engine depends only on the temperatures of the two heat reservoirs between which it operates, and is given by the expression: efficiency = 1 - (Tc/Th) where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir. In this case, the cold reservoir is at 0°C (273 K) and the hot reservoir is at 100°C (373 K), the maximum temperature at which water and steam coexist at 1.0 atm pressure. Therefore: efficiency = 1 - (273/373) = 0.267 or 26.7% (approximately).
To know more about Carnot engine, click here https://brainly.com/question/14680478
#SPJ11
a step-down transformer is 95% efficient and has two times as many primary turns as secondary turns. (a) if the secondary winding carries a current of 10 amps at an rms voltage of 120 volts, what are the primary current and voltage? (b) what is the peak voltage in the primary?
To solve this problem, we'll need to use the formula for transformer efficiency, which is:
efficiency = (output power / input power) x 100%
We know that the transformer is 95% efficient, so we can write:
0.95 = (output power / input power) x 100%
Simplifying this equation, we get:
output power = 0.95 x input power
Now, let's move on to part (a) of the question. We're given that the secondary winding carries a current of 10 amps at an rms voltage of 120 volts. Since the transformer is step-down, the voltage on the primary side will be higher than the voltage on the secondary side. We can use the formula for the voltage ratio of a transformer to find the primary voltage:
primary voltage / secondary voltage = primary turns / secondary turns
We're told that the transformer has two times as many primary turns as secondary turns, so we can substitute in:
primary voltage / 120 = 2 / 1
Simplifying this equation, we get:
primary voltage = 240 volts
Now, we can use the formula for power to find the primary current:
power = voltage x current
On the secondary side, the power is:
power = 120 volts x 10 amps = 1200 watts
Since the transformer is 95% efficient, the input power will be:
input power = output power / 0.95 = 1200 watts / 0.95 = 1263 watts
Now we can use the power formula again to find the primary current:
1263 watts = 240 volts x primary current
primary current = 1263 watts / 240 volts = 5.263 amps
So the primary current is 5.263 amps and the primary voltage is 240 volts.
Moving on to part (b) of the question, we're asked to find the peak voltage in the primary. We know that the rms voltage on the primary side is 240 volts, so we can use the formula for the peak voltage of an AC waveform to find the peak voltage:
peak voltage = rms voltage x √2
Substituting in:
peak voltage = 240 volts x √2 = 339.4 volts
So the peak voltage in the primary is 339.4 volts.
(a) In a step-down transformer with 2 times as many primary turns as secondary turns, the primary voltage will be twice the secondary voltage, and the primary current will be half the secondary current, considering the transformer's efficiency. Given a secondary current of 10 amps and an rms voltage of 120 volts, the primary current and voltage can be calculated as follows:
Primary current = (Secondary current * Efficiency) / 2
Primary current = (10 A * 0.95) / 2 = 4.75 A
Primary voltage = Secondary voltage * 2
Primary voltage = 120 V * 2 = 240 V
So, the primary current is 4.75 amps, and the primary voltage is 240 volts.
(b) To calculate the peak voltage in the primary, we'll use the following formula:
Peak voltage = √2 * rms voltage
Peak voltage = √2 * 240 V ≈ 339.41 V
The peak voltage in the primary is approximately 339.41 volts.
To know more peak voltage visit:
https://brainly.com/question/24334542
#SPJ11
constants a 508 g mass oscillates with an amplitude of 11.0 cm on a spring whose spring constant is 24.0 n/m .A. Determine the period T= ....... s B. Determine the maximum speed Vmax= ...... m/s C. Determine the total energy Wtotal= ........ J
The period T is 0.738 s, the maximum speed [tex]V_{max[/tex] 0.722 m/s and the total energy [tex]W_{total[/tex] is 0.264 J.
What is energy?Energy is the capacity of a physical system to do work. It is a fundamental property of the universe that can be transferred and transformed from one form to another. Energy can take many forms, such as kinetic, thermal, electrical, nuclear, chemical, and gravitational energy. It is a measure of how much work can be done by a system.
A. The period of an oscillating system is given by T = 2π√(m/k), where m is the mass and k is the spring constant. Substituting in the given values we have:[tex]T = 2\pi\sqrt{(508 g/24.0 n/m)} = 2\pi\sqrt{(0.508 kg/24.0 N/m)} = 2\pi\sqrt{(0.021 kg/m) = 0.738s}[/tex]
B. The maximum speed of an oscillating system is given by [tex]V_{max[/tex] = √([tex]kx_{max/m[/tex]), where k is the spring constant, xmax is the amplitude of the oscillation, and m is the mass. Substituting in the given values we have:
[tex]V_{max[/tex] = √(24.0 N/m * 0.11 m/508 g) = √(2.64 N/m/0.508 kg) = √(5.23 m/s²/kg) = 0.722 m/s
C. The total energy of an oscillating system is given by Wtotal = ½ [tex]kx^2_{max[/tex], where k is the spring constant and xmax is the amplitude of the oscillation. Substituting in the given values we have:
[tex]W_{total[/tex] = ½ * 24.0 N/m * (0.11 m)² = 0.264 J.
To learn more about energy
https://brainly.com/question/25959744
#SPJ4
