Explain how osmosis is related to the predictions you made in question 2

According to Bernoulli's Principle, pressure inside a flowing fluid falls as speed increases. The behaviour of an ideal fluid moving through a pipe or other confined tube, like a pump, is explained by the Bernoulli's Principle. Thus, option B is correct.

It's critical to state the principle accurately because how it is expressed can affect its ramifications. In reality, the Bernoulli principle states that in a flow of constant energy, fluid flow speeds up when it passes through a zone of lower pressure and vice versa.

As the total amount of energy must remain constant (energy conservation), this means that the random molecule energy or pressure must decrease in order for the stream flow energy to increase.

Therefore, pressure decreases when velocity of fluid flow increases.

Learn more about fluid here:

https://brainly.com/question/11937154

#SPJ4

Decrease in pressure creates a net force acting on the piston, which pushes in the direction, piston inward and reduces the volume of the air inside the syringe.

When a capped syringe is plunged into cold water, the air inside the syringe will cool down and its volume will decrease. This change in volume will cause a change in presspistonure inside the syringe, which will cause the syringe piston to move in a particular direction.

Assuming that the temperature of the syringe and the water is initially in equilibrium, the pressure inside the syringe is equal to the atmospheric pressure outside the syringe. When the syringe is plunged into cold water, the air inside the syringe cools down and its volume decreases. This decrease in volume causes a decrease in the pressure inside the syringe, which is now lower than the atmospheric pressure outside the syringe. The result is a net force acting on the piston, which pushes the piston inward and reduces the volume of the air inside the syringe.

To see why this happens, we can use the ideal gas law, which states that the pressure, volume, and temperature of a gas are related by the equation PV = nRT,

[tex]P_1V_1 = nRT_1[/tex]

[tex]P_2V_2 = nRT_2[/tex]

here,

[tex]P_2[/tex] & [tex]V_2[/tex] are the final pressure and volume of the air inside the syringe.

Since the number of moles of air inside the syringe is constant, we can write:

[tex]P_1V_1 = P_2V_2[/tex]

If the volume of the air inside the syringe decreases, as it does when the syringe is plunged into cold water, then the pressure inside the syringe must also decrease. This means that the pressure inside the syringe is now lower than the atmospheric pressure outside the syringe. The result is a net force acting on the piston, which pushes the piston inward and reduces the volume of the air inside the syringe.

In summary, when a capped syringe is plunged into cold water, the air inside the syringe cools down and its volume decreases, which causes a decrease in the pressure inside the syringe. This decrease in pressure creates a net force acting on the piston, which pushes the piston inward and reduces the volume of the air inside the syringe.

To know more about Piston please refer: https://brainly.com/question/28044328

#SPJ4

The normal force will be greater than 8 kN because the car will experience an additional downward force due to gravity.

The maximum speed that the vehicle can travel without 16 kN.

The car will feel an additional downward force from gravity, therefore the normal force will be more than 8 kN.

a) When the car passes over the crest, the normal force is one-half of the weight of the car. This means that the normal force is 1/2 x 16 kN = 8 kN. As the car passes through the bottom of the dip,

b) To determine the greatest speed at which the car can move without leaving the road at the top of the hill, you can use the following equation:

centrifugal force = [tex](mass \times velocity^2)[/tex] / radius

The centrifugal force is the force that acts outward when an object moves in a circular path. In this case, the circular path is the crest of the hill. The mass of the car is known to be 16 kN / 9.81 [tex]m/s^2[/tex] = 1,630 kg (assuming g = 9.81 [tex]m/s^2[/tex]). The radius of the crest of the hill is given to be 250 m. You can rearrange the equation to solve for velocity:

velocity = sqrt((centrifugal force x radius) / mass)

The maximum velocity at the crest of the hill is the velocity at which the centrifugal force is equal to the weight of the car:

centrifugal force = weight = 16 kN

Substitute the values into the equation to find the maximum velocity.

c) Once you have found the maximum velocity, you can use the same equation as in part a) to find the normal force on the car as it moves through the bottom of the dip. The normal force will be greater than 8 kN because the car will experience an additional downward force due to gravity.

For such more question on force

https://brainly.com/question/12785175

#SPJ4

Azimuth is measured in degrees, with a full circle having 360 degrees, counting clockwise from north. A ten degree south of east object has an azimuth of 100 degrees.

Azimuth circles have 360 degrees in them. 90 degrees is equivalent to the east, 180 to the south, 270 to the west, 360 to the north, and 0 to the north. a horizon arc that is measured from a fixed point, such as true north, to the vertical arc that passes across the center of an object. Your azimuth is the line. You must now calculate the line's grid azimuth, or the angle between the line and grid north. Learn the concepts azimuth and direction by memorizing flashcards with terms like Ten degrees south of you, a brilliant star may be seen in the southern sky.

The term azimuth is used in astronomy and navigation to describe the horizontal angle between an object's direction and true north. The east is at 90 degrees, the south is at 180 degrees, and the west is at 270 degrees since it is often measured in degrees clockwise from the north.

To know more about azimuth angle on

https://brainly.com/question/30665819

#SPJ4

The magnitude of the average acceleration of the jetliner is 2.07 m/s².

An object's change in velocity over time is gauged by its average acceleration. It is computed by dividing the velocity change by the period of time during which the change takes place.

The formula for average acceleration is:

average acceleration = (final velocity - initial velocity) / time interval

Where the final velocity is the velocity of the object at the end of the time interval, the initial velocity is the velocity of the object at the beginning of the time interval, and the time interval is the duration of the interval over which the velocity changes.

Average acceleration is a vector quantity, meaning it has both magnitude and direction. The direction of the acceleration vector is the same as the direction of the change in velocity. The unit of average acceleration in the International System of Units (SI) is meters per second squared (m/s²).

To calculate the magnitude of average acceleration for the jetliner:

To know more about average acceleration, visit:

https://brainly.com/question/26246639

#SPJ4

The instantaneous acceleration of the mass when it is raised 6.30 cm and compresses the spring 2.50 cm is 16.26 m/s^2.

To solve this problem, we can use the equation for the force exerted by a spring:

F = -kx

When the mass is suspended at rest from the spring, the force exerted by the spring balances the weight of the mass, so we can write:

kx = mg

Solving for the spring constant, we get:

k = mg / x

Substituting the given values, we have:

k = (0.106 kg)(9.81 m/s^2) / 0.0380 m = 27.36 N/m

When the mass is raised 6.30 cm, the displacement of the spring is x = -0.0250 m (since the spring is compressed by 2.50 cm). The force exerted by the spring is:

F = -kx = -(27.36 N/m)(-0.0250 m) = 0.684 N

By Newton's second law, the net force on the object is:

Fnet = ma

where a is the instantaneous acceleration of the object.

The net force is the sum of the force exerted by the spring and the weight of the object:

Fnet = F + mg = 0.6875 N + (0.106 kg)(9.81 m/s^2) = 1.7239 N

Solving for the acceleration, we get:

a = Fnet / m = 1.7239 N / 0.106 kg = 16.2632 m/s^2

Read more about Law's of Motion:

https://brainly.com/question/13868212

#SPJ4

The acceleration of the pebble stuck in the tread goes by three times every second is 106.592 m/s².

Diameter = 60 cm, Radius = 60/2 = 30 cm = 30/100 = 0.3 m.

The pebble in the tread goes by 3 times every second.

This is the same as 3 times per second.

Recall the unit of frequency is Hertz or per second, s⁻¹

So 3 times per second, Frequency, f = 3s⁻¹ or 3 Hertz

For angular motion:

Angular speed, ω = 2πf

                        = 2*π*3

                        = 6π   rad/s

Linear speed, v = ωr =  6π * 0.3 = 1.8π m/s

Linear acceleration, a = v² / r

                              a = 1.8π * 1.8π / 0.3 = 10.8π²   m/s²

Angular acceleration α = a/r  = 10.8π² / 0.3 = 36π² rad/s²

Angular speed = 6π rad/s ≈ 18.840 rad/s

The linear speed of the pebble = 1.8π  m/s ≈ 5.655 m/s

The angular acceleration = 36π² rad/s² ≈ 355.306 rad/s²

The linear acceleration of the pebble = 10.8π²  m/s ≈ 106.592 m/s²

The rate at which the speed and direction of a moving object vary over time. A point or object going straight ahead is accelerated when it accelerates or decelerates. Even if the speed is constant, motion on a circle accelerates because the direction is always shifting.

Learn more about Acceleration:

https://brainly.com/question/1466119

#SPJ4

a. x = √2mgh / k

b. the compression would increase by a factor of √2

c. After the car has been brought to rest, the potential energy would then be converted into the kinetic energy

Let the mass of the car be w

spring constant = R

a. conservation of energy

energy at 1 = energy at the ground after compression

mgh = 1/2kx^2

x² = 2mgh / k

x = √2mgh / k

2. h = 2h

x = √2mgh / k

x = [tex]\sqrt[2]{mgh/k}[/tex]

x = √2 * x

compression increases by √2

3. After the car has been brought to rest, the potential energy would then be converted into the kinetic energy

Read more on potential energy here:https://brainly.com/question/14427111

#SPJ1

The elongation of the spring is 19.9 cm.

What is Buoyant force?

Buoyant force is the upward force exerted on an object when it is immersed or floating in a fluid. It is a result of the pressure difference between the top and the bottom of the object due to the weight of the fluid it displaces. The magnitude of the buoyant force is equal to the weight of the displaced fluid. This is why objects that are less dense than the fluid they are in will float, while objects that are more dense will sink.

The buoyant force acting on the block of wood is given by:

FB = ρVg

where ρ is the density of the water, V is the volume of the displaced water, and g is the acceleration due to gravity.

The volume of the displaced water is equal to the volume of the block, which is given by:

V = m/ρ

= 4.15 kg / 661 kg/m³

= 0.006273 m³

So, the buoyant force is:

FB = ρVg = 1000 kg/m³ * 0.006273 m³ * 9.8 m/s² = 61.38 N

At equilibrium, the weight of the block is balanced by the spring force and the buoyant force:

mg = ks + FB

where m is the mass of the block, g is the acceleration due to gravity, k is the spring constant, s is the elongation of the spring, and FB is the buoyant force.

Solving for s, we get:

s = (mg - FB) / k

s = (4.15 kg * 9.8 m/s² - 61.38 N) / 166 N/m

s = 0.199 m = 19.9 cm

Therefore, the elongation of the spring is 19.9 cm.

Learn more about Buoyant Force from given link

https://brainly.com/question/28464280

#SPJ1

Assuming the red ball was moving in a positive direction when it first collision with the blue ball, the blue ball's velocity after the impact is -9 m/s (indicating it is moving in the opposite direction).

When two bodies, such as two pool cues, a golf club and a ball, a hammer and a nail, two railroad cars when united, or a falling object and a floor, abruptly and forcefully meet in close proximity to one another, it results in a collision, also known as an impact.

Before the impact, the system's total momentum is:

p before = m1v1 + m2v2

Substituting the given values:

p before = (10 kg)(6 m/s) + (8 kg)(-11 m/s) = -2 kg m/s

Following the collision, the system's overall momentum is:

p after = m1v1' + m2v2'

The law of conservation of momentum states that the total momentum of the system before and after the collision is the same, so:

p before = p after

Using the given values as substitutes, find v2':

-2 kg m/s = (10 kg)(6 m/s) + (8 kg)(v2')

v2' = (-2 kg m/s - 60 kg m/s) / 8 kg

v2' = -9 m/s

To know more about collision visit:-

https://brainly.com/question/4322828

#SPJ1

Unpolarized light passes through a Polaroid filter and emerges as polarised light with vibrations in a single plane and half the intensity of unpolarized light. Because of the chemical makeup of the filter material, Polaroid filters can polarize light.

The intensity of the unpolarized light is I

Intensity of the light after 1 st polariser I ' = I /2

Intensity of the light after 2 nd polariser I " = 37 %of I = 0.37 I

from malus law I " = I ' cos 2 θ

from this orientation θ = cos -1 ( √[ I " / I] )

                                θ = cos -1 ( √[ 0.37 I / I/2 ] )

                                θ = cos -1 ( √[ 0.37 *2 ] )

                                θ = cos -1 (0.86023 )

                                = 30.65 degrees

                                ~ 31 degrees

Therefore, 31 degrees is the angle between the transmission axes of the filter.

Learn more about polarization here:

https://brainly.com/question/29217577

#SPJ4

Energy bonds for utilities tied to Bakken shale oil are especially risky because of the volatile nature of the oil industry and because their oil is expensive to extract due to its geographic location.

The Bakken shale oil fields in North Dakota and Montana have been a major source of oil production in the United States, but the industry has seen a lot of ups and downs in recent years. This volatility can make it difficult for utilities to accurately predict their revenues and expenses, which can make it difficult to repay the bonds.

Additionally, the Bakken shale oil fields are subject to a number of environmental and regulatory risks, which can also impact the profitability of the utilities. As a result, energy bonds for utilities tied to Bakken shale oil are considered to be especially risky investments.

Learn more about shale oil at https://brainly.com/question/13689453

#SPJ11

The fundamental frequency of a string that is fixed at both ends is given by

f = v /2sL

where v and L are the speed of sound and string length, respectively.

The amount of time it takes for the wave to travel the length of the string, on the other hand, is given by

t = L/v

As a result, we have

t = L/v

t = v /2f /v

t = 1 /2f

t = 1 /2f

t= 1/2(255hz)

t=1.96 *10⁻³s

The fundamental frequency is computed as f = v/2*L, where v is the speed of the sound wave and L is the length of a tube or device through which the wave is moving. Wavelength multiplied by frequency equals speed. The wave length in this equation is given in metres, while the frequency is measured in hertz (Hz), or the number of waves per second. As a result, wave speed is expressed in metres per second, the SI unit of speed. If the frequencies are all integers or precise multiples of a fundamental frequency, the greatest common divisor of the frequencies can be used. If the frequencies are 1760, 2200, and 3080, then the fundamental frequency is 440 since it is the greatest common divisor.

Learn more about frequency from here;

https://brainly.com/question/2140860

#SPJ4

Free-fall is the state of motion where an object is accelerating due to gravity alone, with no other forces acting on it. Everything inside the ISS is also in free-fall, the astronauts and everything else in the station are weightless

In free-fall, an object is said to be weightless because it experiences zero normal force, which is the force that a surface exerts on an object to support its weight.

When an astronaut is inside the International Space Station, they are essentially in a state of constant free-fall around the Earth. The ISS is in a low-Earth orbit, which means that it is moving fast enough to continuously fall towards the Earth but also fast enough to miss it due to the curvature of the Earth. They experience no normal force and feel as though they are floating in microgravity.

To know more about the free-fall, here

brainly.com/question/10579318

#SPJ4

In wireless systems, wavelength is often expressed in metres (m), centimetres (cm), or millimetres (mm). Wavelength is typically represented by the Greek symbol lambda (λ).

The wavelength is the separation between the corresponding points of two succeeding waves, and is equal to the speed (v) of a wave train in a medium divided by its frequency (f). When two points or particles are referred to be "corresponding points," it means that they are both in the same phase and have completed exactly the same portions of their periodic motion. Typically, the wavelength of transverse waves—those whose points advance at right angles to one another—is measured from crest to crest or from trough to trough; for longitudinal waves—those whose points advance in the same direction—the wavelength is measured from compression to compression or from rarefaction to rarefaction.

Learn more about Wavelength here:

https://brainly.com/question/7143261

#SPJ4

A meteorite crater is a depression created when a spacecraft from another planet or solar system collides with Earth or another relatively big solid body, such as the Moon, another planet and its satellites, or larger asteroids and comets. Thus, option A is correct.

A crater will most likely be created at the point of impact when a meteor impacts a planet. The size of the crater will increase as the object moves faster and becomes larger or heavier. The biggest predictors of impact crater size are the meteor's mass and velocity.

When a smaller solid object, such as an asteroid or meteorite, strikes the surface of a bigger solid object, such as a planet or moon, an impact crater is created.

Therefore, approximately big will the crater be 50 to 100 m in diameter.

Learn more about meteor here:

https://brainly.com/question/11504264

#SPJ4

V = sqrt (KE * 2 / m) = 4.913 m/s, where KE = 0.5 * 0.58 * 1.6*1.6 = 0.7424 J. (c) Work done = change in KE = 7 - 0.7424 = 6.2576 J.

Work is the energy used by one thing to move another object across a distance by applying a force. The equation W = F x d calculates the work done on an item with a given force, F, and a certain distance, d. It should be noted that this equation presupposes that the force is applied in a direction parallel to the object's direction of motion. How to manage non-parallel circumstances will be covered in a later lecture.

When we apply force "F" to a block, the body moves with some acceleration or, moreover, its speed increases or decreases depending on the direction of the force. The system's kinetic energy changes as speed increases or decreases.

Learn more about Work done here:

https://brainly.com/question/10334435

#SPJ4

The complete question is:

A 0.58 kg rubber ball has a speed of 1.60 m/s at point A and kinetic energy of 7.0 J at point B. (a) Determine the ball's kinetic energy at A (b) Determine the ball's speed at B (c) Determine the total work done on the ball from A to B

The wavelength of the light producing the fringe pattern is  (2 * 0.237 mm) / 798 = 0.00059mm.=590nm

To solve for the wavelength of the light producing the fringe pattern, we can use the formula:

wavelength = (2 * distance moved by mirror M2) / (number of fringes shifted)

Plugging in the values given, we get:

wavelength = (2 * 0.237 mm) / 798 = 0.00059 mm=590nm

Therefore, the wavelength of the light producing the fringe pattern is 0.00059 mm.

In a Michelson interferometer, a beam of light is split into two parts by a semi-transparent mirror called a beam splitter. One part of the beam travels to a fixed mirror, while the other part of the beam travels to a movable mirror. The two reflected beams recombine at the beam splitter and create an interference pattern that can be observed. By moving the movable mirror, the phase difference between the two beams changes, causing the interference pattern to shift. By measuring the number of fringes shifted and the distance the mirror is moved, it is possible to determine the wavelength of the light.

To learn more about wavelength, refer:

https://brainly.com/question/17161594

#SPJ4

Exothermic reactions have negative enthalpy because they release more energy than they take in. Consider this to be the quantity of heat that is emitted from (or removed from) the reaction.

A reaction is endothermic and will have a positive enthalpy if it absorbs or utilises more energy than it produces.

Energy is needed to dissociate atom bonds. It is liberated by forming new bonds.

The energy needed to dissolve the bonds between the reactants less the energy produced during the creation of new bonds in the products is the enthalpy of the reaction.

Examining the enthalpy changes during methane burning

In this reaction, the bonds between the oxygen atoms and the carbon atoms as well as the hydrogen atoms and carbon atoms are severed. These connections must be broken, which causes the reaction to consume energy.

New bonds then develop between carbon and oxygen as well as between hydrogen and oxygen.

Learn more about Enthalpy here:

https://brainly.com/question/13996238

#SPJ4

The closer the equipotential surfaces are to each other in a particular region, the stronger the electric field is in that region. The larger the distance between the equipotential surfaces, the weaker the electric field in that region. The distance between the equipotential surfaces is directly proportional to the strength of the electric field in that region.

The strength of the electric field in a region can be determined by the distance between the equipotential surfaces. If the equipotential surfaces are closely spaced, then the electric field in that region is strong. Conversely, if the equipotential surfaces are spaced far apart, then the electric field is weak. This is because the potential difference between two adjacent equipotential surfaces is directly proportional to the electric field strength in that region. Therefore, the closer the equipotential surfaces, the higher the potential difference, and the stronger the electric field.

To know more about Equipotential Surfaces visit:

https://brainly.com/question/14908372

#SPJ4

The mean and the standard deviation of the five measurements are 3.33kg and 1.038 kg respectively.

Standard deviation is a measure of the spread or dispersion of a set of data values. It is calculated by taking the square root of the variance, which is the average of the squared differences from the mean. It measures how much variation or dispersion from the average exists in the data set. A higher standard deviation indicates that the data points are spread out over a larger range of values, while a low standard deviation indicates that the data points are clustered closely around the average. Standard deviation is a commonly used measure in statistics and is used to compare the variability of different data sets.

To find the mean and standard deviation of these five measurements, use the following formulas:

Mean = (sum of all measurements) / (number of measurements)

Standard deviation = sqrt((sum of squared differences from the mean) / (number of measurements - 1))

First, find the mean:

Mean = (3.5 + 3.2 + 3.8 + 3.4 + 5.5) / 5 = 3.88 kg

So the mean mass of the five bricks is 3.88 kg.

Next, we can find the standard deviation:

Calculate the differences from the mean for each measurement:

-0.38, -0.68, 0.92, -0.48, 1.62

Square each difference:

0.1444, 0.4624, 0.8464, 0.2304, 2.6244

Add up the squared differences:

4.308

Divide the sum by the number of measurements minus one:

4.308 / (5-1) = 1.077

Take the square root of the result:

sqrt(1.077) = 1.038

So the standard deviation of the five measurements is 1.038 kg.

To know more about Standard Deviation, visit:

https://brainly.com/question/475676

#SPJ4

The charge on capacitor C2 is 3.367 microcoulombs.

To determine the charge on capacitor C2, we can use the formula for capacitance:

C = Q / V

where C is the capacitance, Q is the charge, and V is the potential difference. We can rearrange this formula to solve for the charge:

Q = C * V

We first need to calculate the equivalent capacitance of the circuit, which can be found by adding the capacitances of C1 and C3 in series, and then adding that result to C2 in parallel. The equivalent capacitance is:

1/Ceq = 1/C1 + 1/C3

1/Ceq = 1/2 µF + 1/1 µF

1/Ceq = 1.5 µF

Ceq = 2/3 µF

Now we can find the charge on C2 by using the formula:

Q = C2 * V

Substituting the known values, we get:

Q = (2/3 µF) * 5.05 V = 3.367 µC

Therefore, the charge on capacitor C2 is 3.367 microcoulombs.

Learn more about capacitor here :

brainly.com/question/14844377

#SPJ4

Answer:

0.089 seconds

Explanation:

The time period of a wave is the reciprocal of its frequency and can be calculated as follows:

T = 1/f

Where T is the time period and f is the frequency.

Therefore, for a wave with a frequency of 11.2 Hz, the time period is:

T = 1/11.2 = 0.089 seconds (to 3 decimal places).

ALLEN

To obtain the lowest power at the detector, move the ideal mirror to the right by 86.2 nm; the lowest power is 0.225 mW.

We can divide a laser beam into two pathways using a 50-50 beam splitter, bounce one route off a perfect mirror, and bounce the other path off a mirror that does not reflect all light to form an interferometer.

In this configuration, interference between the two laser light streams can result in a pattern of both constructive and destructive interference that can be picked up by a detector.

We can adjust the ideal mirror to the right to create a minimal power at the detector if the measured power is initially at its maximum. This is due to the fact that shifting the mirror can alter the interference pattern by changing the distance between the two pathways taken by the laser light.

We may utilize the fact that the measured power is highest when the two laser light streams are in phase and minimum when they are out of phase to calculate how far we need to move the ideal mirror. The power measured at the detector when just the vertical arm is blocked is 2.25 mw, and when only the horizontal arm is blocked, it is 2.025 mw.

Power detected at detector is:

P = (1/2) * [tex]P_in[/tex] * (1 +- [tex]cos(Δφ)[/tex]))

where [tex]P_in[/tex] : incident power, Δφ : light phase difference and the ± sign depends on whatever path is blocked.

When power: maximum, phase difference :integral multiple of [tex]2\pi[/tex], i.e., Δφ = [tex]2\pi n[/tex]. When the power is minimum, the phase difference is an odd multiple of π, i.e., Δφ = [tex](2n+1)\pi /2.[/tex]

Solve phase difference:

Δφ = [tex]arccos[(4P_min/P_in) - 1][/tex]

[tex]P_min[/tex] :min power at detector =  2.025 mw.

Substitute values:

Δφ = [tex]arccos[(4*2.025/9) - 1] = 2.18 radians[/tex]

To find detector power, change the phase difference to [tex](2n+1)\pi /2[/tex]. Move perfect mirror by a distance Δx :

Δφ = [tex](2n+1)\pi /2 = 1.57, 4.71, 7.85, ...[/tex]

We use laser wavelength to find distance Δx:

Δx = Δφ * λ / [tex]2\pi[/tex]

λ: laser wavelength wavelength which is 400 nm

Substitute values:

Therefore,

Δx = 86.2 nm

Learn more about power here:

https://brainly.com/question/14780060

#SPJ4

The brightness of a star increases as it becomes bigger. It stands to reason that a larger star would have a larger surface. The larger surface area allows for the emission of more light and energy. The temperature of a star also affects its luminosity. Thus option E is correct.

The amount of light emitted from a star's surface, on the other hand, is referred to as brightness. The relationship between apparent brightness and luminosity changes with distance.

The size and effective temperature of a star can be used to calculate its brightness. The former is often expressed in terms of solar radii, whilst the latter is typically expressed in kelvins, but neither is typically physically measurable.

Therefore, 1/9 as bright. So it must appear fainter. Since brightness scales as 1/d^2 it will appear 3^2=9 times fainter.

Learn more about star here:

https://brainly.com/question/13912549

#SPJ4

Answer:

electron is the correct answer

Explanation:

pls mark me as brainlist

The exterior or housing, the audio reception and speaker system, the picture tube, and a complicated mass of electronics including cable.

Antennae input and output devices, a built-in antenna in most sets, a remote control receiver, and computer chips, make up the four main sets of parts that make up a television.

Typically, in addition to coaxial cable, HDMI, and other audio-video connectors, smart TVs also enable Ethernet, WiFi, USB, Bluetooth, and flash memory cards from digital cameras.

Therefore, the TV consists of exterior, audio reception, speaker system, and picture tube.

Learn more about TV, here:

https://brainly.com/question/24030285

#SPJ9

The middle layer of a capacitor should be made of an insulator.

A capacitor is a passive electronic component that is used to store and release electrical energy in an electrical circuit.

A capacitor works by separating two conductive plates with an insulating material (the dielectric). When a voltage is applied to the plates, electric charge is stored in the dielectric and the capacitor can hold electrical energy.

Therefore, the middle layer of the capacitor must be an insulator so that it can prevent the electric charge from flowing between the two outer plates, and enable the build-up of as much potential as possible. If the middle layer were made of a conductor or a semiconductor, the capacitor would not work as intended.

Learn more about capacitors here:

https://brainly.com/question/25273702

#SPJ2

The physical properties of gold, such as its malleability, ductility, and electrical/thermal conductivity, are important for making synthetic products from gold.

Physical properties are characteristics of a material that can be observed without changing the composition of the material. Examples of physical properties include color, density, hardness, electrical conductivity, melting point, boiling point, and solubility.

From a chemical perspective, gold is a relatively inert element, meaning it is resistant to oxidation and other chemical reactions. This makes it ideal for use in applications where it may be exposed to harsh environments or corrosive materials, such as medical implants and aerospace components. Additionally, gold's unique properties make it suitable for use in catalytic reactions, meaning it can speed up chemical reactions without itself being consumed or affected. This is used in a variety of industries, such as the production of pharmaceuticals, food additives, and polymers.

To learn more about physical properties
https://brainly.com/question/19921381
#SPJ1