Given the transfer function \(G(s)=\frac{1}{(s+1)(s+2)}\) and PD controller\(D_{c}(s)=K \frac{(s+z)}{(s+4)}\), the following are the steps to determine the zero value and the damped natural frequency:i) When the value of K tends to infinity, the transfer function can be written as,\(D_{c}(s)=K \frac{(s+z)}{(s+4)}\)On substituting [tex]K = ∞,\(D_{c}(s)=\frac{\infty \cdot (s+z)}{(s+4)}\)Therefore, at z = -4,[/tex]
the system becomes neutrally-stable.ii) The given transfer function can be written in the following standard second-order form:\(G(s)=\frac{\omega_{n}^{2}}{(s+2\zeta\omega_{n})^{2}+\omega_{n}^{2}}\)where \(\zeta\) = damping ratio and \(\omega_{n}\) = natural frequency of the system.
The given PD controller can be written as,\(D_{c}(s)=K \frac{(s+10)}{(s+4)}\)On substituting this value in the characteristic equation,\(1+G(s)D_{c}(s)=0\)\(1+\frac{\omega_{n}^{2}K(s+z)}{(s+2\zeta\omega_{n})^{2}+\omega_{n}^{2}}=0\)On equating the coefficients of numerator and denominator, we get,\(\omega_{n}^{2}K=\frac{1}{1}\) \(\Rightarrow \omega_{n}=\sqrt{\frac{1}{K}}\) and \(\omega_{n}=\sqrt{2}\)z = 10, substituting the values in the equation, \(\omega_{d}=\omega_{n}\sqrt{1-\zeta^{2}}\)\(\omega_{d}=\sqrt{\frac{1}{K}}\sqrt{1-\zeta^{2}}\)\(\omega_{d}=\sqrt{2}\sqrt{1-\zeta^{2}}\)Therefore, the damped natural frequency \(ω_d\) in radians/sec when the system has the controller \(D_c(s)=K(s+10)/(s+4)\) is \(ω_d = \sqrt{2}\sqrt{1-\zeta^{2}}\)
To know more about transfer visit:
https://brainly.com/question/31945253
#SPJ11
9. As mentioned in class, one of the most problematic nuclides produced during nuclear fission is strontium-90, which decays by ß decay with a half-life of 28 years. (a) What is the daughter nucleus of the decay? (b) How long would you have to wait for the original level to be reduced to 6.25% of its original value?
Strontium-90 is a problematic nuclide produced during nuclear fission. It decays by ß decay with a half-life of 28 years.
In this question, we are asked to determine the daughter nucleus of the decay and calculate the time required for the original level to be reduced to 6.25% of its original value.
The daughter nucleus of strontium-90 decay is yttrium-90. During ß decay, a neutron in the strontium-90 nucleus is converted into a proton, resulting in the transformation of strontium-90 into yttrium-90.
To calculate the time required for the original level of strontium-90 to be reduced to 6.25% of its original value, we can use the concept of half-life.
Since the half-life of strontium-90 is 28 years, it means that after every 28 years, the quantity of strontium-90 will reduce to half of its previous value.
To find the time required for a reduction to 6.25% (1/16th) of the original value, we need to determine how many half-lives are needed. Since each half-life reduces the quantity by half, the number of half-lives required can be calculated by:
n = log2(1/16) ≈ 4
Therefore, it would take approximately 4 half-lives or 4 * 28 years = 112 years for the original level of strontium-90 to be reduced to 6.25% of its original value.
Learn more about Strontium-90 from the given link:
https://brainly.com/question/33196206
#SPJ11
Measurement of curvature radius of lens by Newton's Ring experimental
How can i calculate the data of diameter using the data of left and right?can u help list the step
To calculate the diameter of a lens using the data of left and right in a Newton's Ring experiment, you can follow these steps:
1. Measure the radius of the lens. This can be done by measuring the distance between the center of the lens and the point where the rings are most closely packed.
2. Calculate the average radius by taking the average of the left and right measurements.
3. Once you have the average radius, you can calculate the diameter of the lens by multiplying the average radius by 2. So, in summary, to calculate the diameter of a lens using the data of left and right in a Newton's Ring experiment, you need to measure the radius of the lens, calculate the average radius, and then multiply the average radius by 2 to obtain the diameter.
Learn more about Newton's Ring experiment:
https://brainly.com/question/16979383
#SPJ11
In an aluminum pot, 0.490 kg of water at 100 °C boils away in four minutes. The bottom of the pot is 3.36 × 10-3 m thick and has a surface area of 0.0291 m2. To prevent the water from boiling too rapidly, a stainless steel plate has been placed between the pot and the heating element. The plate is 2.03 × 10-3 m thick, and its area matches that of the pot. Assuming that heat is conducted into the water only through the bottom of the pot, find the temperature in degrees Celsius at the steel surface in contact with the heating element.
The temperature at the steel surface in contact with the heating element is approximately -383.3333 °C.
The temperature in degrees Celsius at the steel surface in contact with the heating element, we can use the principle of heat conduction and apply Fourier's law of heat conduction.
The rate of heat transfer (Q) through a material is given by:
Q = -kA(dT/dx)
Where:
Q is the rate of heat transfer (in watts)
k is the thermal conductivity of the material (in watts per meter per Kelvin)
A is the cross-sectional area of heat transfer (in square meters)
(dT/dx) is the temperature gradient (in Kelvin per meter)
In this case, the heat is conducted through the aluminum pot and the stainless steel plate. Since we are interested in the temperature at the steel surface, we will consider the heat transfer through the steel plate.
Let's calculate the rate of heat transfer through the steel plate:
Thickness of the steel plate (x) = 2.03 × 10^(-3) m
Area of the steel plate (A) = 0.0291 m^2
To calculate the temperature gradient (dT/dx), we need to determine the temperature difference across the steel plate.
We know that the water is boiling away at 100 °C. Assuming that the aluminum pot and the steel plate are in thermal equilibrium, the temperature at the inner surface of the steel plate is also 100 °C.
Let's assume the temperature at the outer surface of the steel plate (in contact with the heating element) is T (in °C).
The temperature difference across the steel plate is then:
ΔT = T - 100
Now we can calculate the rate of heat transfer through the steel plate:
Q = -kA(dT/dx)
Q = -kA(ΔT/x)
The mass of water that boils away (m) is given as 0.490 kg. To find the heat transferred, we can use the latent heat of vaporization of water (L) which is 2.26 × 10^6 J/kg.
The heat transferred can be calculated as:
Q = mL
Q = (0.490 kg)(2.26 × 10^6 J/kg)
Q = 1.1074 × 10^6 J
Now, we can rearrange the equation for the rate of heat transfer through the steel plate and solve for T:
Q = -kA(ΔT/x)
1.1074 × 10^6 J = -k(0.0291 m^2)((T - 100) °C / (2.03 × 10^(-3) m))
Simplifying the equation:
1.1074 × 10^6 J = -k(14.2857 m)(T - 100) °C
Let's assume the thermal conductivity of stainless steel (k) is approximately 16 W/(m·K).
Now we can solve for T:
1.1074 × 10^6 J = -16 W/(m·K)(14.2857 m)(T - 100) °C
Simplifying further:
1.1074 × 10^6 J = -2285.7143 W/(K)(T - 100) °C
Dividing both sides by -2285.7143 W/(K):
-483.3333 = T - 100
T = -483.3333 + 100
T = -383.3333 °C
Therefore, the temperature at the steel surface in contact with the heating element is approximately -383.3333 °C.
Learn more about temperature from the given link:
https://brainly.com/question/27944554
#SPJ11
Continuous-wave Laser based robot sensor detected two closest objects might be collided. Laser beam modulation frequency f=1MHs and phase shifts of beams reflected from first and second objects are φ1= π/3 and φ2= π/4. Calculate, please the distances to both of objects and distances between them. Give brief to calculations.
The distances to both objects are (π / 48) μm, and the distance between them is 0 μm, indicating that the two objects are in contact or overlapping each other.
The distances to the two objects and the distance between them can be calculated using the information provided. Let's break down the calculations step by step:
Determine the wavelength (λ) of the laser beam:
The modulation frequency (f) is given as 1 MHz, which corresponds to 1 million cycles per second.
Since it's a continuous-wave laser, each cycle represents one wavelength.
Therefore, the wavelength can be calculated as the reciprocal of the modulation frequency: λ = 1 / f = 1 / (1 MHz) = 1 μm.
Calculate the phase differences (Δφ) between the reflected beams:
The phase shift (φ) of the beam reflected from the first object is given as π/3.
The phase shift (φ) of the beam reflected from the second object is given as π/4.
The phase difference between the two objects can be calculated as Δφ = |φ1 - φ2| = |π/3 - π/4| = |(4π - 3π) / 12| = π / 12.
Calculate the distances to each object:
The distance to the first object (d1) can be calculated using the formula: d1 = λ * Δφ / (4π).
Substituting the values: d1 = (1 μm) * (π / 12) / (4π) = (π / 48) μm.
Similarly, the distance to the second object (d2) can be calculated as: d2 = λ * Δφ / (4π).
Substituting the values: d2 = (1 μm) * (π / 12) / (4π) = (π / 48) μm.
Calculate the distance between the two objects (d):
The distance between the two objects is simply the difference between the distances to each object: d = |d2 - d1|.
Substituting the values: d = |(π / 48) μm - (π / 48) μm| = 0 μm.
Therefore, the distances to both objects are (π / 48) μm, and the distance between them is 0 μm, indicating that the two objects are in contact or overlapping each other.
Know more about Laser Wave here:
https://brainly.com/question/4589284
#SPJ11
An ideal gas initially at 340 K undergoes an isobaric expansion at 2.50 kPa. The volume increases from 1.00 m3 to 3.00 m3 and 13.8 kJ is transferred to the gas by heat.
(a) What is the change in internal energy of the gas?
kJ
(b) What is the final temperature of the gas?
K
(a) The change in internal energy of the gas is 8.8 kJ in an isobaric process.
(b) The final temperature of the gas is 5.10 K, determined using the ideal gas law.
(a) To calculate the change in internal energy of the gas, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system. In this case, the process is isobaric, which means the pressure remains constant.
We can calculate the work done by the gas using the formula: work = pressure * change in volume. Since the pressure is constant at 2.50 kPa, and the volume changes from 1.00 m³ to 3.00 m³, the change in volume is 3.00 m³ - 1.00 m³ = 2.00 m³.
So, the work done by the gas is: work = 2.50 kPa * 2.00 m³ = 5.00 kJ.
The heat added to the gas is given as 13.8 kJ.
Therefore, the change in internal energy of the gas is: change in internal energy = heat added - work done = 13.8 kJ - 5.00 kJ = 8.8 kJ.
(b) To find the final temperature of the gas, we can use the ideal gas law, which states that the product of pressure and volume is directly proportional to the absolute temperature of the gas.
The initial temperature of the gas is given as 340 K. We know that the pressure remains constant at 2.50 kPa, and the volume changes from 1.00 m³ to 3.00 m³.
Using the ideal gas law, we can set up the equation: (initial pressure) * (initial volume) / (initial temperature) = (final pressure) * (final volume) / (final temperature).
Plugging in the values, we have: 2.50 kPa * 1.00 m³ / 340 K = 2.50 kPa * 3.00 m³ / (final temperature).
Simplifying, we get: 1.4706 kPa*m³/K = 7.50 kPa*m³ / (final temperature).
To find the final temperature, we can rearrange the equation to solve for it: final temperature = 7.50 kPa*m³ / (1.4706 kPa*m³/K) = 5.10 K.
Therefore, the final temperature of the gas is 5.10 K.
To know more about first law of thermodynamics, refer to the link below:
https://brainly.com/question/3808473#
#SPJ11
A person places olive oil in a bottle. The person then inserts a cork with a 2.42 cm diameter into the bottle, placing it in direct contact with the olive oil. If the bottom of the bottle has a 12.57 cm diameter, and the person applies a force of 56 N to the cork, what is the force (in N) exerted on the bottom of the bottle?
A person places olive oil in a bottle. The person then inserts a cork with a 2.42 cm diameter into the bottle, placing it in direct contact with the olive oil. If the bottom of the bottle has a 12.57 cm diameter, and the person applies a force of 56 N to the cork, The force (in N) exerted on the bottom of the bottle is 56 N.
The area of the cork is given by the formula below:
A = πr²
where r is the radius of the cork and it is half of the diameter.
Thus,
The radius of the cork r = 2.42/2 = 1.21 cm.
Area of the cork = π(1.21)²=4.59 cm²
The force (in N) exerted on the cork can be calculated using the formula:
F = PA
Where P is the pressure and A is the area.
The pressure is equal to the force divided by the area.
So, F/A = P
Thus, F = PA
The area of the bottom of the bottle is also given by the formula: A = πr²
where r is the radius of the bottom of the bottle and it is half of the diameter. Thus, the radius of the bottle r = 12.57/2 = 6.285 cm.
Area of the bottom of the bottle = π(6.285)²=124.61 cm²
The force exerted on the bottom of the bottle (F₂) can be calculated by multiplying the pressure (P) by the area (A) of the bottom of the bottle. Thus:
F₂ = P.A₂
where P is the pressure and A₂ is the area of the bottom of the bottle.
The pressure is equal to the force (F) divided by the area (A) of the cork. So, P = F/A.
The force exerted on the cork (F) is given as 56 N and the area of the cork is given as 4.59 cm².
Thus the pressure exerted on the cork is given as:
P = F/A= 56/4.59= 12.18 Pa
Therefore, F₂ = P.A₂= 12.18 × 124.61= 1513.34 N ≈ 1513 N
Therefore, the force (in N) exerted on the bottom of the bottle is 1513 N.
To know more about force exerted refer to:
https://brainly.com/question/30452713
#SPJ11
A resistor \( R \) and a capacitor \( C \) are connected in series to a battery of terminal voltage \( V_{0} \). Which of the following equations relating 1. \( V_{0}-C \frac{d Q}{d t}-I^{2} R=0 \) he
Option (D) is the correct answer.
The given equation is [tex]\(V_0 - C\frac{dQ}{dt} - I^2R = 0\)[/tex]
Now let's see if this option matches the given equation. If we differentiate V with respect to time, we get dV/dt. And we know that the charge on the capacitor is Q = CV, thus differentiating Q with respect to time gives us dQ/dt = C(dV/dt).
Substituting these in the given equation gives:[tex]$$V_{0}-C\frac{dQ}{dt}-I^{2} R=0$$$$V_{0} - C \cdot C\frac{dV}{dt} - I^{2}R = 0$$[/tex]
Now we need to replace the[tex]\(\frac{dV}{dt}\) term with \(-I \frac{1}{C} - IR\)[/tex]from option (D).
Replacing that gives us:[tex]$$V_{0} - C \cdot C(-I \frac{1}{C} - IR) - I^{2}R = 0$$$$V_{0} + I + I^{2}R = 0$$[/tex]
Multiplying by -1 and rearranging gives us:[tex]} $$I^{2}R + IR + V_{0= 0$$[/tex]which is the given equation.
Thus, option (D) is the correct answer.
A capacitor is a passive electrical component that stores energy in an electric field. When a voltage difference is applied across the terminals of a capacitor, electric charges of equal magnitude but opposite polarity build up on each plate. It is used in electronic circuits for blocking direct current while allowing alternating current to pass, for filtering out noise, and for energy storage.
To know more about capacitor visit:
https://brainly.com/question/31627158
#SPJ11
Calculate the energy of a photon emitted when an electron undergoes a transition of n=3 to n=1
The energy of the photon emitted when an electron undergoes a transition of n=3 to n=1 is approximately 2.18 x 10^-18 J.
To calculate the energy of the photon emitted when an electron undergoes a transition of n=3 to n=1, we can use the formula E = hf, where E is the energy of the photon, h is Planck's constant, and f is the frequency of the photon.
First, let's calculate the wavelength of the photon using the formula λ = R(1/n1^2 - 1/n2^2), where R is the Rydberg constant and n1 and n2 are the initial and final energy levels of the electron.
Substituting the values n1 = 3 and n2 = 1 into the formula, we get:
λ = R(1/3^2 - 1/1^2)
Simplifying the equation, we have:
λ = R(1/9 - 1)
Next, let's calculate the frequency of the photon using the formula f = c/λ, where c is the speed of light and λ is the wavelength of the photon.
Substituting the value of λ into the formula, we get:
f = c/λ = c/(R(1/9 - 1))
Finally, we can calculate the energy of the photon using the formula E = hf, where h is Planck's constant and f is the frequency of the photon.
Substituting the value of f into the formula, we get:
E = h * (c/(R(1/9 - 1)))
Calculating the value using the given constants, we find:
E = (6.626 x 10^-34 J·s) * (3.00 x 10^8 m/s) / (1.097 x 10^7 m^-1 * (1/9 - 1))
After evaluating the expression, we find that the energy of the photon emitted during the electron transition is approximately 2.18 x 10^-18 J.
Learn more:About energy of photon here:
https://brainly.com/question/2393994
#SPJ11
The energy of the photon emitted during the electron transition from n=3 to n=1 is approximately 2.42 x [tex]10^{-18[/tex] Joules.
The energy of a photon emitted during an electron transition can be calculated using the equation:
E = (hc) / λ
Where:
E is the energy of the photon
h is Planck's constant (6.626 x [tex]10^{-34[/tex] J·s)
c is the speed of light (3.00 x [tex]10^8[/tex] m/s)
λ is the wavelength of the photon
To determine the energy of a photon emitted during the transition from n=3 to n=1, we need to calculate the wavelength of the emitted photon. We can use the Rydberg formula to find the wavelength:
1/λ = R * (1/n1² - 1/n2²)
Where:
R is the Rydberg constant (1.097 x [tex]10^7[/tex] [tex]m^{-1[/tex])
n1 and n2 are the initial and final energy levels, respectively.
Plugging in the values, we have:
n1 = 3
n2 = 1
1/λ = R * (1/1² - 1/3²)
Simplifying:
1/λ = R * (1 - 1/9)
1/λ = R * (8/9)
1/λ = (8/9)R
Rearranging the equation:
λ = (9/8) * (1/R)
Now, we can substitute the value of R and calculate λ:
λ = (9/8) * (1/1.097 x[tex]10^7[/tex] [tex]m^{-1[/tex])
λ ≈ 8.18 x[tex]10^{-8[/tex] meters
Finally, we can calculate the energy of the photon using the equation E = (hc) / λ:
E = (6.626 x [tex]10^{-34[/tex] J·s * 3.00 x [tex]10^8[/tex] m/s) / (8.18 x [tex]10^{-8[/tex] meters)
E ≈ 2.42 x [tex]10^{-18[/tex] Joules
To know more about Rydberg formula refer here
https://brainly.com/question/13185515#
#SPJ11
The chemical formula for glucose is C6H12O6. Therefore, four molecules of glucose will have( )carbon atoms,( )hydrogen atoms, and()oxygen atoms..
Four molecules of glucose will have 24 carbon atoms, 48 hydrogen atoms, and 24 oxygen atoms.
The chemical formula for glucose is[tex]C_{6}H_{12}O_{6}[/tex], which indicates the number and type of atoms present in a glucose molecule.
In glucose, there are 6 carbon (C) atoms, 12 hydrogen (H) atoms, and 6 oxygen (O) atoms in each molecule. To determine the number of atoms in four molecules of glucose, we multiply the number of atoms in one molecule by four.
Carbon (C) atoms: In one molecule of glucose, there are 6 carbon atoms. Multiplying this by four, we get 6 * 4 = 24 carbon atoms in four molecules of glucose.
Hydrogen (H) atoms: In one molecule of glucose, there are 12 hydrogen atoms. Multiplying this by four, we get 12 * 4 = 48 hydrogen atoms in four molecules of glucose.
Oxygen (O) atoms: In one molecule of glucose, there are 6 oxygen atoms. Multiplying this by four, we get 6 * 4 = 24 oxygen atoms in four molecules of glucose.
Therefore, four molecules of glucose will have 24 carbon atoms, 48 hydrogen atoms, and 24 oxygen atoms.
In summary, the chemical formula [tex]C_{6}H_{12}O_{6}[/tex] indicates the number and type of atoms in one molecule of glucose. By multiplying these values by four, we can determine the number of atoms in four molecules of glucose
For more such questions on glucose, click on:
https://brainly.com/question/397060
#SPJ8
The displacement of the mass m is detected by utilizing the movable plate capacitor. The capacitor is charged by the ideal constant voltage source V.. Assume that movable plate capacitance is electrically linear.
The displacement of the mass m is detected by utilizing the movable plate capacitor. The capacitor is charged by the ideal constant voltage source V. It is assumed that the movable plate capacitance is electrically linear.The circuit of the movable-plate capacitor is one that depends on the force being exerted on the plate.
The movement of the mass modifies the force exerted on the plate, causing a change in capacitance and therefore a change in the voltage. A higher mass causes a lower voltage, whereas a lower mass causes a higher voltage.In addition to this, there is a large frequency dependence of the mass detection.
The use of a resonant circuit, such as a piezoelectric crystal, can overcome this problem. The circuit's resonant frequency varies depending on the mass's position, and the resonant frequency shift can be determined by measuring the circuit's capacitance change. A shift in the resonant frequency indicates that the mass has moved.
To learn more about displacement visit;
https://brainly.com/question/11934397
#SPJ11
Charge q1 = 1.50 nC is at
x1 = 0 and charge q2 = 5.00
nC is at x2 = 2.50 m. At what point between the
two charges is the electric field equal to zero? (Enter the
x coordinate in m.)
HINT
m
The x coordinate at which the electric field is zero is 1.25 m.
From the question above, charge q1 = 1.50 nC is at x1 = 0 and charge q2 = 5.00 nC is at x2 = 2.50 m and we have to find out the point between two charges where the electric field is equal to zero.
The electric field due to a point charge q at a distance r from it is given by;E = (kq)/r²
Where, k is a constant and its value is 9 × 10^9 Nm²/C²
The electric field at any point on the axial line joining two point charges is given by;
E = (kq)/(r₁)² - (kq)/(r₂)²
Where, r₁ and r₂ are the distances of the point from the two charges respectively.On equating the above equation to zero, we get;
(kq)/(r₁)² = (kq)/(r₂)²(r₁)² = (r₂)²r₁ = r₂
Using the distance formula, the distance between the two charges can be calculated as follows;d = √(x₂ - x₁)²= √(2.50 - 0)²= √6.25= 2.5 m
Now, the distance between two charges can be divided into two equal parts such that they make a right angle at the point of division.
Since the electric field is proportional to 1/r², we know that the midpoint of the line connecting two point charges is the point at which the electric field is zero.
So, the x-coordinate of the point midway between the charges is;x = x₁ + d/2= 0 + 2.5/2= 1.25 m
Therefore, the x coordinate at which the electric field is zero is 1.25 m.
Learn more about electric field at
https://brainly.com/question/30460697
#SPJ11
coil spans of coil pitch??
A t-pole threc-phace 60H \( 2+ \) stator glots synchrosous gelkerator. The evif piteh factor of the fifte harmonic compoaent is zero. The coll spasis for of the piolepiticl.
A synchronous generator consists of a stator and a rotor, both of which are made up of electrical conductors and coils. The stator's electrical conductor is wound in a number of slots, with each slot carrying a concentrated coil of several turns. When the rotor rotates in the stator's magnetic field,
the alternating current (AC) is induced in the stator's winding. The poles, slots, and coils are arranged in such a way that they form a particular pitch. Coil span and coil pitch are the two terms used to describe the arrangement of poles, slots, and coils in a synchronous generator. Coil pitch is a term used to describe the distance between the two corresponding coil sides in adjacent slots,
and coil span is a term used to describe the distance between the two opposite coil sides in the same slot. In a synchronous generator, the pole pitch (the distance between two poles in the rotor) is determined by the number of slots in the stator and the number of poles in the rotor. To create a sine wave of voltage, the coils must be located such that the distance between the two sides of a coil in one slot is equal to the distance between the two sides of a coil in the next slot. This distance is called the coil pitch. If this distance is increased or decreased, it will result in voltage waveform distortion, and the generator's output voltage will no longer be a pure sine wave.
To know more about synchronous visit:
https://brainly.com/question/27189278
#SPJ11
which energy yield is likely to have come from a fission or fusion reaction?
1.0×10^2 kj/mol
1.2×10^3 kj/mol
2.5×10^2 kj/mol
1.4×10^11 kj/mol
Energy yield is likely to have come from a fission or fusion reaction is 1.4×10^11 kj/mol.
Nuclear fission and nuclear fusion are the two types of nuclear reactions. A large amount of energy is released in both nuclear reactions, but there is a significant difference between the two in terms of the amount of energy generated and the radioactive waste produced.
Nuclear fission and nuclear fusion are two types of nuclear reactions.
Nuclear fission is a nuclear reaction in which a large nucleus is split into two smaller nuclei, releasing a large amount of energy.
Nuclear fusion is a nuclear reaction in which two smaller nuclei combine to form a larger nucleus, releasing a large amount of energy.
This type of reaction is also referred to as thermonuclear fusion since it only occurs at extremely high temperatures. Now, let us determine the energy yield that is likely to have come from a fission or fusion reaction.
From the energy yields given, it is clear that the energy yield of 1.4×10^11 kj/mol is the only one that is likely to have come from a fusion reaction, not a fission reaction.
Fission reactions generate a much smaller amount of energy.
Therefore, the answer to the question is 1.4×10^11 kj/mol.
Learn more about nuclear reaction from:
https://brainly.com/question/1420545
#SPJ11
Find the Brewster angle when medium 1 is free space and medium 2
has a relative permittivity of 25.
The Brewster angle is approximately 78.69 degrees.
Brewster angle is the angle of incidence at which the light reflected from a surface is completely polarized.
The Brewster angle can be calculated using the formula: tan θB = n2/where θB is the Brewster angle, n1 is the refractive index of the first medium, and n2 is the refractive index of the second medium.
When medium 1 is free space and medium 2 has a relative permittivity of 25, the refractive index of medium 2 is given by:n2 = √25 = 5
Since the refractive index of free space is 1, substituting into the formula gives: tan θB = 5/1 = 5θB = tan⁻¹(5) ≈ 78.69°
To know more about polarized light please refer:
https://brainly.com/question/3092611
#SPJ11
10) How fast must a proton move so that its kinetic energy is 60% of its total energy?
A) 0.82c
B) 0.87c
C) 0.92c
D) 0.98c
E) 0.80c
The correct answer is option (C) 0.92c.
Solution: We know that the total energy E of a proton is given by; E = (m₀/m) x [1/(1-(v²/c²))]
Where; v = speed of the proton m₀ = rest mass of the proton m = relativistic mass of the proton, given by; m
= m₀/[1-(v²/c²)]¹/²
As per the question, kinetic energy of the proton is 60% of its total energy.
So, K.E. of the proton = 60% of E or K.E. = 0.6E
And, the kinetic energy of the proton is given by;
K.E. = (m - m₀)c²/(√1-(v²/c²) - m₀c²)
Putting the value of m in the above equation, we get; K.E. = {m₀/[√1-(v²/c²)] - m₀} x c²
Thus, 0.6E = {m₀/[√1-(v²/c²)] - m₀} x c²⇒ (3/5)E
= {m₀/[√1-(v²/c²)] - m₀} x c²
⇒ 3/[5{m₀/[√1-(v²/c²)] - m₀}] = c²/E
⇒ [3(1-(v²/c²))]/{5√1-(v²/c²)}
= c²/E⇒ 3(1-(v²/c²))
= 5c²[1-(v²/c²)]⇒ v²/c²
= (2/5)
So, v = c√(2/5)⇒ v/c = 0.632455532
⇒ v/c = 0.632The value of v/c is closest to 0.92c.
Therefore, option (C) 0.92c is the correct answer.
To know more about proton visit:
https://brainly.com/question/12535409
#SPJ11
Which of the following statements from Dalton's atomic theory is no longer true, according to modern atomic theory?
the statement from Dalton's atomic theory that is no longer true is "Atoms are indivisible and cannot be divided into smaller particles."
Dalton's atomic theory, proposed in the early 19th century, stated that atoms were indivisible and indestructible particles, meaning they could not be further divided into smaller particles. However, with advancements in scientific understanding and the development of subatomic particle physics, it has been discovered that atoms are not indivisible. Atoms are composed of subatomic particles, namely protons, neutrons, and electrons. Protons and neutrons reside in the nucleus at the center of the atom, while electrons orbit around the nucleus. Furthermore, scientists have identified even smaller particles within the nucleus, such as quarks and gluons. Hence, the concept of atoms being indivisible, as proposed in Dalton's atomic theory, is no longer valid based on modern atomic theory.
To learn more about photons, click here: https://brainly.com/question/33017722
#SPJ11
Which of the following statements from Dalton's atomic theory is no longer true, according to modern atomic theory?
A) All atoms of a given element are identical.
B) Atoms are not created or destroyed in chemical reactions.
C) Elements are made up of tiny particles called atoms.
D) Atoms are indivisible and cannot be divided into smaller particles.
What would be the maximum voltage value needed to
provide an effective or RMS value of 240 volts?
The maximum voltage needed to provide an effective or RMS value of 240 volts is approximately 339.4 volts.
The maximum voltage value needed to provide an effective or RMS value of 240 volts can be determined using the relationship between the maximum voltage (Vmax) and the RMS voltage (Vrms) in an AC circuit.For a sinusoidal waveform, the RMS voltage is related to the maximum voltage by the equation: Vrms = Vmax / √2.To find the maximum voltage, we rearrange the equation:Vmax = Vrms * √2Plugging in the given RMS voltage value of 240 volts:Vmax = 240V * √2, Vmax ≈ 339.4 volts. Therefore, the maximum voltage needed to provide an effective or RMS value of 240 volts is approximately 339.4 volts.
To learn more about voltage:
https://brainly.com/question/32002804
#SPJ11
3) (10 points) You are at home watching some old cartoons during Christmas break. Naturally, your mind wanders back to the happy times in physics class. You notice that Wiley Coyote chases the Road Runner. You estimate that the Road Runner is about 94.5 cm tall, so then you estimate that Road Runner has about a 15.0 m head start and accelerates at about 2.75 m/s². Given this information, what is the smallest constant speed that Wiley Coyote has to run at to catch the Road Runner?
The smallest constant speed that Wiley Coyote has to run at to catch the Road Runner is approximately 9.5 m/s. When the smallest constant speed of the Wiley Coyote is to be determined to catch the Road Runner, a kinematic equation can be used for solving this problem.
When the smallest constant speed of the Wiley Coyote is to be determined to catch the Road Runner, a kinematic equation can be used for solving this problem. The equation is:
v_f² = v_i² + 2a(x_f - x_i)
Here, the initial velocity of the Wiley Coyote is taken as 0 m/s. The final velocity v_f will be the speed that Wiley Coyote has to run at to catch the Road Runner. The acceleration a is given as 2.75 m/s² and the distance covered by the Road Runner is taken as 15.0 m + 94.5 cm = 16.395 m. When all these values are substituted in the equation, the following is obtained:
v_f² = 0 + 2(2.75 m/s²)(16.395 m)≈90.1 m²/s²v_f ≈ 9.5 m/s
Therefore, the smallest constant speed that Wiley Coyote has to run at to catch the Road Runner is approximately 9.5 m/s. When we have to determine the smallest constant speed of the Wiley Coyote that is required to catch the Road Runner, the initial velocity is 0 m/s, acceleration is 2.75 m/s², distance covered by the Road Runner is 15.0 m + 94.5 cm = 16.395 m, and the final velocity v_f is the speed that Wiley Coyote has to run at to catch the Road Runner.
The given kinematic equation is used to find v_f which is: v_f² = v_i² + 2a(x_f - x_i)
Here, v_i is 0 m/s. Hence, we have:
v_f² = 0 + 2(2.75 m/s²)(16.395 m)≈90.1 m²/s²
Now, we can find v_f by taking the square root of v_f²:
v_f ≈ √(90.1 m²/s²)≈9.5 m/s
Therefore, the smallest constant speed that Wiley Coyote has to run at to catch the Road Runner is approximately 9.5 m/s.
To know more about kinematic equation visit:
https://brainly.com/question/24458315
#SPJ11
Describe the trend of the chirp signal in frequency over time.
And when there is a down-chirp from 250˙kHz to DC with a pulse
width of 50μs. calculate its B, tau, and time-bandwidth products.
And wr
1) B (chirp bandwidth) is 250 kHz.
2) Tau (chirp duration is 50 μs.
3) Time-Bandwidth Product is = 12.5
4) In the case of the down-chirp with the given parameters, the equation would be:
s(t) = A * exp(j * (2π * (250 kHz * t - (125 kHz/2) * t²)))
The trend of a chirp signal in frequency over time depends on whether it is an up-chirp or a down-chirp.
In an up-chirp, the frequency of the signal increases over time. This means that the signal starts with a lower frequency and gradually rises to a higher frequency.
In a down-chirp, the frequency of the signal decreases over time. The signal starts with a higher frequency and gradually decreases to a lower frequency.
For the specific down-chirp mentioned, it starts at 250 kHz and decreases to DC (0 Hz) with a pulse width of 50 μs.
To calculate the parameters:
1) B (chirp bandwidth): B is the difference between the initial and final frequencies.
B = 250 kHz - 0 Hz
= 250 kHz.
2) Tau (chirp duration): Tau is the pulse width of the chirp signal.
Tau = 50 μs.
3) Time-Bandwidth Product: The time-bandwidth product represents the trade-off between time and frequency resolution. It is calculated by multiplying the bandwidth (B) by the duration (Tau).
Time-Bandwidth Product = B * Tau
= (250 kHz) * (50 μs)
= 12.5.
4) The complex envelope equation for the linear FM pulse waveform of the down-chirp can be expressed as:
s(t) = A * exp(j * (2π * (f0 * t + (B/2) * t²)))
where:
s(t) represents the complex envelope of the signal.
A is the amplitude of the signal.
j is the imaginary unit.
f0 is the initial frequency of the chirp.
t represents time.
B is the chirp bandwidth.
In the case of the down-chirp with the given parameters, the equation would be:
s(t) = A * exp(j * (2π * (250 kHz * t - (125 kHz/2) * t²)))
Learn more about Higher Frequency at
brainly.com/question/21974895
#SPJ4
A 28 AWG magnet wire will be used to
create a 12V DC solenoid lock that draws
about 650mA. Please derive the
mathematical modeling of the lock to
understand how much wire is needed,
magnetic field, force, and other key
mathematical components to develop the
lock. Please prove all equations with
explanations along with differential
equations.
F = (B^2 * A)/(2μ), where F is the force, B is the magnetic field strength, A is the area of the solenoid, and μ is the permeability of free space. Using the values given, we can calculate the magnetic field strength and the force of the solenoid as follows:
B = (μ * n * I) / l
= (4π * 10^-7 * 1000 * 0.65) / (0.3048)
= 6.97 x 10^-4 T
This value is less than 1T, which means that we can approximate the magnetic field strength using the linear formula B = μ * n * I/L, where L is the length of the solenoid.
L = (μ * n^2 * I^2) / (2 * B^2 * A)
= (4π * 10^-7 * (500)^2 * (0.65)^2) / (2 * (6.97 x 10^-4)^2 * (π * (0.00635/2)^2))
= 0.0328 m
The amount of wire needed can be determined using the formula for the length of the wire; Lw = π * d * n, where Lw is the length of the wire, d is the diameter of the wire, and n is the number of turns. Lw = π * 0.0127 * 500 = 198.9 m
Approximately 200m of 28 AWG magnet wire would be needed to create the 12V DC solenoid lock that draws about 650mA.
To know more about magnet visit:
https://brainly.com/question/3617233
#SPJ11
Please help me to solve in detail the following questions. I really need to understand the way to answer this question. Thank you so much!
Enter the solar-zenith angles (Summer Solstice, Autumn Equinox, Winter Solstice, and Spring Equinox) for the cities on each of the following dates. (Remember, all answers are positive. There are no negative angles.)
a) Cairo, Egypt is located at 31.251o Longitude, 30o Latitude.
b) Kolkata, India is located at 88.334o Longitude, 22.5o Latitude.
c) Manila, Philippines is located at 120.967o Longitude, 14.6o Latitude.
d) Lagos, Nigeria is located at 3.3o Longitude, 6.45o Latitude.
e) Santa Clause's workshop is at the North Pole. What is the solar-zenith angle of Santa's shop on the Winter Solstice?
a) Cairo, Egypt: Solar-zenith angle is 60° for all dates. b) Kolkata, India: Solar-zenith angle is 67.5° for all dates. c) Manila, Philippines: Solar-zenith angle is 75.4° for all dates. d) Lagos, Nigeria: Solar-zenith angle is 83.55° for all dates. e) North Pole: Solar-zenith angle is 90° on the Winter Solstice.
To determine the solar-zenith angles for the given cities on specific dates, we need to calculate the angle between the zenith (directly overhead) and the position of the Sun at the specified times. The solar-zenith angle is dependent on the latitude, longitude, and date. Here are the solar-zenith angles for each city and date:
a) Cairo, Egypt:
Summer Solstice (June 21): Solar-zenith angle = 90° - θ, where θ is the latitude (30°). Therefore, solar-zenith angle = 90° - 30° = 60°.
Autumn Equinox (September 23): Solar-zenith angle = 90° - θ = 90° - 30° = 60°.
Winter Solstice (December 21): Solar-zenith angle = 90° - θ = 90° - 30° = 60°.
Spring Equinox (March 21): Solar-zenith angle = 90° - θ = 90° - 30° = 60°.
b) Kolkata, India:
Summer Solstice (June 21): Solar-zenith angle = 90° - θ, where θ is the latitude (22.5°). Therefore, solar-zenith angle = 90° - 22.5° = 67.5°.
Autumn Equinox (September 23): Solar-zenith angle = 90° - θ = 90° - 22.5° = 67.5°.
Winter Solstice (December 21): Solar-zenith angle = 90° - θ = 90° - 22.5° = 67.5°.
Spring Equinox (March 21): Solar-zenith angle = 90° - θ = 90° - 22.5° = 67.5°.
c) Manila, Philippines:
Summer Solstice (June 21): Solar-zenith angle = 90° - θ, where θ is the latitude (14.6°). Therefore, solar-zenith angle = 90° - 14.6° = 75.4°.
Autumn Equinox (September 23): Solar-zenith angle = 90° - θ = 90° - 14.6° = 75.4°.
Winter Solstice (December 21): Solar-zenith angle = 90° - θ = 90° - 14.6° = 75.4°.
Spring Equinox (March 21): Solar-zenith angle = 90° - θ = 90° - 14.6° = 75.4°.
d) Lagos, Nigeria:
Summer Solstice (June 21): Solar-zenith angle = 90° - θ, where θ is the latitude (6.45°). Therefore, solar-zenith angle = 90° - 6.45° = 83.55°.
Autumn Equinox (September 23): Solar-zenith angle = 90° - θ = 90° - 6.45° = 83.55°.
Winter Solstice (December 21): Solar-zenith angle = 90° - θ = 90° - 6.45° = 83.55°.
Spring Equinox (March 21): Solar-zenith angle = 90° - θ = 90° - 6.45° = 83.55°.
e) North Pole (Santa's workshop):
Winter Solstice (December 21): At the North Pole, the solar-zenith angle on the Winter Solstice would be 90° since the Sun is at its lowest point in the sky, just above the horizon.
To know more about Solar-zenith angle refer here
brainly.com/question/33036372
#SPJ11
The getaway spaceship of a group of Andorian bank robbers passes the origin of an inertial reference frame S with constant speed v=0.96 in the +x direction at t=0. At the same moment in the same frame, the Romulan ship that is pursuing them passes the x=−500 s at constant speed v=0.99 in the same direction. Assume both ships maintain their constant velocities. Frame S′ moves with the same velocity as the Romulan ship, buts its origin coincides with that of frame S at t=t′=0. (Use SR units for this problem, and give answers to 3 significant digits) (a) In frame S, when and where do the Romulans catch up to the Andorians? (b) In frame S′, when and where do the Romulans catch up to the Andorians? (c) In frame S′, what is the velocity of the Andorian ship? (d) How much time passes on a clock on the Andorian ship between the moment it passes the origin of S and the moment the Romulans catch up to them? (e) How much time passes on a clock on the Romulan ship between the event t=0,x=−500 s (in S ) and the moment it overtakes the Andorian ship? (f) The Romulans have trapped the Andorians in their tractor beam so that both ships now move with the same constant velocity. A Romulan boarding party takes a shuttle across the 3.00 km between the two ships. The shuttle accelerates at a=50.0 m/s2 relative to the Romulan ship for the first half of the trip and then decelerates at the same rate for the other half of the trip. What is the time of the shuttle flight in the inertial frame of the ships? (g) What is difference between the time recorded on the ships and the time recorded on the shuttles during the shuttle flight?
(a) In frame S: Romulans catch up at t=505.05 s, x=0.500 km.
(b) In frame S': Romulans catch up at t'=0, x'=0.
(c) In frame S': Andorian ship velocity is v'=0.99.
(d) On Andorian ship: Δt=0.521 s between origin and capture.
(e) On Romulan ship: Δt=0.505 s between event and capture.
(f) Shuttle flight time in ship frame: t=24.5 s.
(g) Time dilation: Ships' time > shuttle's time due to velocity.
(a) In frame S, the Romulans catch up to the Andorians when their positions align. The Andorians pass the origin of frame S at t=0, so the time it takes for the Romulans to catch up is given by:
Δt = Δx/v = (500 s)/(0.99) = 505.05 s.
The Romulans catch up to the Andorians at t = 505.05 s, and their position is:
x = −500 s + vΔt = −500 s + (0.99)(505.05 s)
= 0.500 km.
(b) In frame S', the Romulans and the Andorians have the same constant velocity, so they are at rest relative to each other. Therefore, the Romulans catch up to the Andorians at t' = 0, and their position is x' = 0.
(c) In frame S', the velocity of the Andorian ship is the same as the velocity of the Romulan ship, v' = 0.99.
(d) In frame S, the time experienced by the Andorian ship between passing the origin of S and being caught by the Romulans is:
Δt = Δx/v = (0.500 km)/(0.96) = 0.521 s.
(e) In frame S, the time experienced by the Romulan ship between t=0, x=−500 s and catching up to the Andorian ship is:
Δt = Δx/v = (0.500 km)/(0.99) = 0.505 s.
(f) The time of the shuttle flight in the inertial frame of the ships can be determined by calculating the time it takes for the shuttle to travel the 3.00 km distance at an average acceleration of 50.0 m/s².
Using the equation x = 0.5at², we find that:
t = √(2x/a) = √((2 * 3000 m) / (50.0 m/s²)) = 24.5 s.
(g) The difference between the time recorded on the ships and the time recorded on the shuttles during the shuttle flight is the result of time dilation due to their relative velocities. As the shuttle moves at a high velocity relative to the ships, time passes slower on the shuttle compared to the ships. This time dilation effect can be calculated using the time dilation formula, but further information is needed, such as the relative velocity between the shuttle and the ships.
To learn more about velocity follow the link:
https://brainly.com/question/30559316
#SPJ4
5. A cubic shark was thrown downwards from the 8th floor of a 27-storey building. The shark was later caught at a position below its starting position. Consider the origin at the 8 th floor. Determine the final velocity of the shark if the shark moved for 1.4 s and was caught 19.5 m below the 8 th floor.
The final velocity of the shark, if the shark moved for 1.4 s and was caught 19.5 m below the 8th floor, is 13.67 m/s.
The 8th-floor shark is thrown downwards, therefore, its acceleration will be due to gravity, g = 9.8 m/s².The formula for displacement, s of a falling object is given by:s = ut + (1/2)gt²Where u is the initial velocity, t is the time taken and g is the acceleration due to gravity.
Using the above formula for the shark, s = displacement = 19.5 m, t = time taken = 1.4 s and g = 9.8 m/s², we can find the initial velocity as follows:19.5 = u(1.4) + (1/2)(9.8)(1.4)²19.5 = 1.4u + 9.716u = (19.5 - 19.432)u = -0.068u = -0.068 / 1.4u = -0.04857 m/s.
The initial velocity of the shark is -0.04857 m/s (negative sign indicates it was thrown downwards). The final velocity of the shark, v = u + gtSubstituting the values of u, t, and g we get:v = -0.04857 + (9.8)(1.4)v = -0.04857 + 13.72v = 13.67143 m/s.
To know more about gravity please refer to:
https://brainly.com/question/31321801
#SPJ11
A parallel-plate capacitor is connected to a battery. What happens to the stored energy UF is plate separation is increased 4 times while the capacitor remains connected to the battery? (iv compare between initial stored energy and final stored energy of the capacitor). A) It decreases by a factor of 2 . B) It decreases by a factor of 3 . C) It decreases by a factor of 4 . D) It remains the same. E) It is doubled.
A parallel-plate capacitor is connected to a battery. When the plate separation of the capacitor is increased 4 times while it remains connected to the battery, the stored energy UF decreases by a factor of 16. the stored energy UF decreases by a factor of 8 when the plate separation is increased 4 times. Therefore, the correct answer is C) It decreases by a factor of 4.
To understand why the stored energy decreases, let's consider the formula for the energy stored in a capacitor:
UF = (1/2) * C * V^2
Where UF is the stored energy, C is the capacitance of the capacitor, and V is the voltage across the capacitor.
In a parallel-plate capacitor, the capacitance C is given by:
C = (ε * A) / d
Where ε is the permittivity of the dielectric material between the plates, A is the area of the plates, and d is the separation between the plates.
If the plate separation is increased 4 times, the new capacitance C' becomes:
C' = (ε * A) / (4d)
Now, let's substitute the new capacitance C' into the formula for stored energy UF:
UF' = (1/2) * C' * V^2
Plugging in the value of C', we get:
UF' = (1/2) * [(ε * A) / (4d)] * V^2
Simplifying this expression, we find:
UF' = (1/8) * (ε * A * V^2) / d
Comparing this expression with the original formula for stored energy UF, we see that UF' is 1/8 times UF:
UF' = (1/8) * UF
In other words, the stored energy UF decreases by a factor of 8 when the plate separation is increased 4 times. Therefore, the correct answer is C) It decreases by a factor of 4.
To know more about capacitance
https://brainly.com/question/30529897
#SPJ11
A transformer is set up so that the electrical power from the windmill is converted to 100 A of current for his house. The wind turbine produces 24kW of power. If the number of turns from the primary coil of the transformer is 3600 and in the second coil is 900. What is the voltage coming into the primary coil and coming out of the secondary coil.
A transformer is set up so that the electrical power from the windmill is converted to 100 A of current for his house. The wind turbine produces 24kW of power. If the number of turns from the primary coil of the transformer is 3600 and in the second coil is 900. The voltage coming out of the secondary coil of the transformer is 60 volts.
The voltage coming into the primary coil and coming out of the secondary coil of the transformer can be found out with the help of the formula,
V1/V2=N1/N2
where V1 is the voltage coming into the primary coil
V2 is the voltage coming out of the secondary coil
N1 is the number of turns from the primary coilN2 is the number of turns from the secondary coil
Given: Number of turns from the primary coil of the transformer is 3600 and in the second coil is 900So,
N1 = 3600
N2 = 900
Current produced by windmill,
I = 100 A = 100 Amperes
Power produced by windmill,
P = 24 kW = 24000 Watts
We know that;
Power = Voltage x Current
P = VI
As per the question, the transformer is set up to convert electrical power from the windmill to 100 A of current.
Using this, we can write;
24000 = V1 x 100Or,
V1 = 24000 / 100
= 240 volts
Thus, the voltage coming into the primary coil of the transformer is 240 volts.The voltage coming out of the secondary coil can be found using the formula mentioned above.
V1/V2 = N1/N
2240/V2 = 3600/900
240/V2 = 4
V2 = 240/4
= 60 volts
Thus, the voltage coming out of the secondary coil of the transformer is 60 volts.
To know more about transformer visit:
https://brainly.com/question/15200241
#SPJ11
what is the role of electrical forces in nuclear fission
Electrical forces initiate and control nuclear fission by overcoming the repulsion between positively charged protons in the nucleus.
Nuclear fission is a process in which the nucleus of an atom splits into two or more smaller nuclei, accompanied by the release of a significant amount of energy. Electric forces, specifically the electrostatic repulsion between positively charged protons, are responsible for initiating and controlling nuclear fission. In a nucleus, protons are packed closely together, and the repulsive electric forces between them must be overcome for fission to occur. This is achieved by bombarding the nucleus with neutrons, which do not carry a charge but can interact through the strong nuclear force. When a neutron collides with a nucleus, it can be absorbed, causing the nucleus to become highly unstable and elongated. The repulsive electric forces then dominate, leading to the splitting of the nucleus into two smaller fragments.
The interplay between the strong nuclear force and the electric forces is crucial in nuclear fission. While the strong nuclear force holds the nucleus together, the electrostatic repulsion between protons needs to be overcome to induce fission. Understanding and controlling the electrical forces involved in nuclear fission is essential for harnessing this process for various applications, including energy production and nuclear reactors.
To know more about Electrical forces click here:
https://brainly.com/question/20935307
#SPJ11
"Q9
please when solving the exercise use equations from the equations sheet attached and please make sure to write the equation you are using ! Thank you so much!
Sea water is flowing at 5.6 m/s through a horizontal pipe that is many miles long. The pressure is 450kPa and the radius of the pipe is 0.06 m. The pipe curves pts downward and the levels out so that it is horizontal again. The radius of the lower is located at 1.3 mat the pipe narrows the lower/right portion of the pipe is in the lower portion of the portion of the pipe flows frsub=
V
obj
V
sub
=
V
obj
V
ft
=
rho
f
rho
ot
y=
L
F
h=
rhogr
2γcosθ
A
1
v
1
=A
2
v
2
P+
2
1
rhov
2
+rhogy= consta
t
E
=(P+
2
1
rhov
2
+rhogy)Q η=
vA
FL
R=
πr
4
8nl
Q=
R
P
2
−P
1
N
n
=
η
2pvr
N
g
∗
=
η
rhovL
x
rms
=
2Dt
T
X
=T
c
+273.15 Ch. 1 rho=
V
m
P=
A
F
\begin{tabular}{l|l}
A
1
F
1
=
A
2
F
2
& PV=N \\ P=rhogh & n=
N
A
N
\end{tabular}"
Answer: Option D : 466280 - 512.5v2^2.
The equation that we are going to use for solving the given problem is Bernoulli's equation(BE). Let's write BE .P1 + 1/2ρv1^2 + ρgh1 = P2 + 1/2ρv2^2 + ρgh2 where pressure(p), velocity(v), density(ρ) of the fluid, h is height, and g is acceleration due to gravity. Now, we will calculate all the variables from the given data;P1 = 450 kPaP2 = ? (to be found)ρ = density of sea water = 1025 kg/m^3v1 = 5.6 m/sv2 = ? (to be found)h1 = h2 (because both points are at the same height)g = 9.81 m/s^2 Equating the pressure values, we get;P2 = P1 + 1/2ρv1^2 - 1/2ρv2^2P2 = 450000 + 1/2(1025)(5.6)^2 - 1/2(1025)v2^2. Note that we are using SI units to maintain consistency.
Substituting the values;P2 = 450000 + 16280 - (v2^2)(512.5)P2 = 466280 - 512.5v2^2. We are not provided with any information regarding the height or depth of the pipe; therefore, we cannot determine the pressure difference using the hydrostatic pressure formula(HPF) (P = ρgh). Thus, we cannot find the value of v2.
To know more about Bernoulli's equation visit:
https://brainly.com/question/15396422
#SPJ11
A spring pendulum with a mass of 50 g attached to it has only 10% of its oscillation amplitude after completing a full swing. For each full swing it takes 10 s. Ignore gravity and calculate the spring constant! Assume you excite the pendulum with a force F(t) Fo sin(t). What value of n is required to make the amplitude maximal? Sketch the resonance curve with properly labelled axes
The graph of amplitude against frequency is called the resonance curve. The resonance curve is given below: Resonance curve for the spring pendulum, with frequency (f) on x-axis and Amplitude (A) on y-axis.
Given that: A spring pendulum with a mass of 50 g attached to it has only 10% of its oscillation amplitude after completing a full swing. For each full swing it takes 10 s. Ignore gravity and calculate the spring constant. Assume you excite the pendulum with a force F(t) Fo sin(t).
We need to find the spring constant for the given pendulum. The time period of the pendulum is given as: T = 10sAngular frequency of oscillations can be given asω = 2π / Tω = 2π / 10 = π / 5 rad/s
As the mass attached to the spring undergoes complete oscillation with only 10% amplitude, the amplitude after one full oscillation can be given as0.1 A0 = A0 cos (ωT)0.1 = cos (π/5)
∴ A0 = 1 cm We know that, the time period and angular frequency of oscillation are related to the spring constant of the pendulum. As the mass oscillates around the equilibrium position with spring force F = -kx, where x is the displacement of the mass from the equilibrium position.
The time period T can be written as: T = 2π / (k / m)1 = 2π (m / k)k = (2π)2m / T2The mass of the spring pendulum is given as 50 g or 0.05 kg. Spring constant k = (2π)2 × 0.05 / 100 = 0.00157 N/m
Now, assume that we excite the pendulum with a force F(t) Fo sin(t).The force can be written as: F(t) = Fo sin(t)Let the amplitude of oscillations for this force be A.
F0 sin (ωt) = ma - kxA/m = -ω2A-kxA
= -ω2A0 sin (ωt)k / m
= ω2k = mω2k = 0.05 (π / 5)2k
= 0.0314 N/m
To make the amplitude maximum, we can write the expression for the amplitude as: A = F0 / mω2 / [k - mω2]
Using this, n can be calculated as:n = ω / 2π
= (π / 5) / (2π) = 0.1
To know more about graph visit:
https://brainly.com/question/17267403
#SPJ11
Q2 The charge entering the positive terminal of an element is
given by the expression q(t) = -20 e^(-4t) mC. The power delivered
to the element is p(t) = 2.6e^(-3t) W. If the solution for v(t) is
in t
Given, The charge entering the positive terminal of an element is q(t) = -20 e^(-4t) mC. The power delivered to the element is p(t) = 2.6e^(-3t) W. the solution for V(s) is (13 / 4) / (s + 1 - (a / 4)).
If the solution for v(t) is in t.
We know, p(t) = v(t) × i(t) ........(1)
Also, i(t) = dq(t) / dt ........(2)
Substituting equation (2) in equation (1), we get,p(t) = v(t) × (dq(t) / dt)
On integrating both sides, we get,
∫p(t) dt
= ∫v(t) (dq(t) / dt) dt
Let the solution for v(t) be,
v(t) = V_0 e^(-at)
So, (dq(t) / dt)
= d / dt [-20 e^(-4t)]
Therefore, dq(t) / dt
= 80 e^(-4t)
On substituting these values in the above equation,
we get∫(2.6e^(-3t)) dt
= ∫(V_0 e^(-at)) (80 e^(-4t)) dt
On solving this equation, we get the value of V_0 as,V_0
= (13 / 4) e^(a/4) .
On substituting the value of V_0 in the solution for v(t), we get
v(t) = (13 / 4) e^(a/4) e^(-at)Taking Laplace transform on both sides, we get
V(s)
= (13 / 4) ∫[e^(-t+(a/4))] e^(-st) dt
On simplifying, we get V(s)
= (13 / 4) / (s + 1 - (a / 4))
Therefore, the solution for V(s) is (13 / 4) / (s + 1 - (a / 4)).
To know more about charge visit :
https://brainly.com/question/30784604
#SPJ11
The equation for calculating how much energy (E in units of Joules) is required to heat an object is E=CmΔT. If we are heating water, the value for C (the specific heat content) is 4100 Joules per kg per Kelvin (or "J/kg/K"). If the water we are heating is 0.1 kg and we heat it 100 degrees, how much energy (E) does it require?
• 41000
• 41
• 0.41
• 4100000000000
The amount of energy (E) required to heat 0.1 kg of water by 100 degrees is 4100 Joules.
The equation for calculating the energy required to heat an object is E = CmΔT, where E represents the energy in Joules, C is the specific heat content in J/kg/K, m is the mass of the object in kg, and ΔT is the change in temperature in Kelvin. For water, the specific heat content (C) is 4100 J/kg/K. In this case, we are heating 0.1 kg of water with a temperature change (ΔT) of 100 degrees. Plugging these values into the equation, we get E = (4100 J/kg/K) * (0.1 kg) * (100 K) = 4100 Joules. Therefore, it requires 4100 Joules of energy to heat 0.1 kg of water by 100 degrees. The specific heat content of water indicates that it takes a relatively high amount of energy to raise its temperature compared to other substances. This property is why water is often used as a coolant or heat transfer medium in various applications. Understanding the energy requirements for heating substances is crucial in fields such as engineering, physics, and chemistry, where precise control and calculations of heat transfer are necessary.
To learn more about amount of energy (E) , Click here:
https://brainly.com/question/33440890
#SPJ11
