hi, need help with this
question
a) Name THREE major yield drivers for a typical Surface Mounted Process (SMT)? (3 marks)

Answers

Answer 1

The three major yield drivers for a Surface Mounted Process (SMT) are:

Component Placement AccuracySolder Paste Printing QualityReflow Soldering Process Control

What is the  major yield drivers

The accuracy of putting components on a printed circuit board is very important for SMT to work properly. If the parts are not in the right place, it can cause problems with melting them together, or the electrical parts might not work.

The way the solder paste is printed is very important for making electronic things work well. The stuff used to stick parts onto a computer board needs to be put on exactly right so the parts stay stuck.

Learn more about   drivers   from

https://brainly.com/question/29796270

#SPJ1


Related Questions

Find the transfer function of the given translational mechanical
system shown below. Provide a solution that will match to
the answer key given below

Answers

The given translational mechanical system is shown below. The transfer function of this system can be determined as follows:Firstly, the free-body diagram of the mechanical system is shown below, in which F is the input force applied to the mass m and x is the output position of the mass.

Therefore, we can write the force balance equation for the mass as:

F - kx - c(dx/dt) - mg = m(d²x/dt²)

where k, c, and m are the spring constant, damping constant, and mass of the mechanical system respectively.

The transfer function can be determined by taking the

Laplace transform of the above equation as follows:F(s) - kX(s) - csX(s)s - mg = ms²X(s)

Rearranging the above equation,

we get:X(s)/F(s) = 1/[ms² + cs + k + mg/s]

Therefore, the transfer function of the given translational mechanical system is X(s)/F(s) = 1/[ms² + cs + k + mg/s].

To know more about force visit:

https://brainly.com/question/30507236

#SPJ11

An induction motor is operating at the rated conditions with 50 Hz supply has stator rms phase current of 40/- 25° A. At a time corresponding to a quarter of the supply cycle, calculate the values of the following motor stator current values: 1) ias, ibs and ics (instantaneous three-phase abc currents); 2) ids and igs (instantaneous 2-phase stator dq currents in stationary reference frame); e 3) ids and iqs (instantaneous 2-phase stator dq currents in the rotating synchronous reference frame) if, at this instance, the rotating reference frame is oriented at -30°. [40 marks]

Answers

1) ias = 40∠-25° A, ibs = 40∠115° A, ics = 40∠-165° A.

2) ids = 40√2∠-55° A, iqs = 40√2∠-55° A.

3) ids = 40√2∠-85° A, iqs = 40√2∠-25° A.

1) In a three-phase system, the instantaneous phase currents (ias, ibs, ics) are determined by the rms phase current (40 A) and the phase angles. Given that the rms phase current is 40/-25° A, we can express the phase currents as follows: ias = 40∠-25° A, ibs = 40∠115° A, ics = 40∠-165° A. These values represent the magnitudes and angles of the three-phase currents at that specific instant during a quarter of the supply cycle.

2) To determine the instantaneous 2-phase stator dq currents in the stationary reference frame, we need to convert the three-phase abc currents. Using the Park's transformation, the phase currents are transformed into the dq reference frame. Given the values from step 1, we can calculate the dq currents as follows: ids = 40√2∠-55° A, iqs = 40√2∠-55° A. Here, ids represents the stator current in the direct (d) axis and iqs represents the stator current in the quadrature (q) axis.

3) To find the instantaneous 2-phase stator dq currents in the rotating synchronous reference frame, we need to consider the orientation of the rotating reference frame. In this case, the rotating reference frame is oriented at -30°. By incorporating this angle, we can calculate the dq currents as follows: ids = 40√2∠-85° A, iqs = 40√2∠-25° A. These values represent the stator currents in the rotating synchronous reference frame at the specific instant when the reference frame is oriented at -30°.

Learn more about instantaneous phase currents:

brainly.com/question/20341821

#SPJ11

Cascade control architecture features nested inner control loops inside the primary (master) loop. b) Determine open loop and closed loop discrete transfer functions of the velocity control Such contr

Answers

Cascade control architecture features nested inner control loops inside the primary (master) loop. In this structure, the output of the primary loop feeds into the secondary loops.

Cascade control is advantageous in situations where precise control is required over multiple variables that are interdependent. The cascade control can provide faster response, better disturbance rejection, and better setpoint tracking.

The open-loop discrete transfer function of the velocity control system is given as:

[tex]$$G_0(s)=\frac{\frac{k_p}{T_i}s+\frac{k_p}{T_iT_d}s^2+k_ps}{s}$$$$G_0(z)=\frac{zT_s\left( 1-\frac{z^{-1}}{z^{-1}+\frac{T_i}{T_s}+\frac{T_d}{T_s}z^{-1}} \right)}{1-z^{-1}}$$[/tex]

where Ts is the sample time.The transfer function of the closed-loop system can be determined as follows:

[tex]$$G_c(s)=\frac{\frac{k_p}{T_i}s+\frac{k_p}{T_iT_d}s^2+k_ps}{s+\frac{1}{T_i}s+\frac{1}{T_d}}$$$$G_c(z)=\frac{k_p\left( 1+\frac{T_s}{T_i}+\frac{T_s}{T_d} \right)z^{-1}-k_p\left( 1+\frac{2T_s}{T_d} \right)+k_p\left( \frac{T_s}{T_d}-\frac{T_s}{T_i}-1 \right)z}{z^{-1}+\left( \frac{T_s}{T_i}+\frac{T_s}{T_d}+1 \right)-\frac{T_s}{T_iT_d}z^{-1}}$$.[/tex]

where Ts is the sample time.

To know more about architecture visit:

https://brainly.com/question/20505931

#SPJ11

Problem 4: Determine the Transfer Function of the Electric System. 1. \( \frac{I 2(s)}{V(s)} \) 2. \( \frac{C 1(s)}{V(s)} \)

Answers

Given the electric circuit shown below, the transfer function of the electric system, [tex]\( \frac{I_2(s)}{V(s)} \) and \( \frac{C_1(s)}{V(s)} \)[/tex] is to be determined.

[tex]\frac{I_2(s)}{V(s)}[/tex]In order to determine the transfer function of the electric system, [tex]\frac{I_2(s)}{V(s)}[/tex], consider the following observation: All current entering node 1 must exit node 2. Also, all current entering node 3 must exit node 4.Therefore, using KCL, [tex]I_1 = I_2 + I_3[/tex].(1) Also, using KCL, [tex]I_2 + I_4 = I_5[/tex].

(2)However, we are interested in the transfer function [tex]\frac{I_2(s)}{V(s)}[/tex]. In order to determine this, first, we need to express all the currents in terms of [tex]V(s)[/tex]. Using the first equation, [tex]I_2 = I_1 - I_3[/tex].Now, we need to express [tex]I_3[/tex] in terms of [tex]V(s)[/tex]. Applying Ohm's Law to resistor [tex]R_2[/tex], [tex]V_{R_2}(s) = I_3(s)R_2[/tex].

To know more about transfer visit:

https://brainly.com/question/31945253

#SPJ11

What (external) performance measures would you recommend the
space x falcon 9 AI System?

Answers

For external performance measures recommended for Space X Falcon 9 AI System, the following should be implemented:For all industries, it's critical to have standard measures of success and performance.

In the aerospace and defense industries, this is particularly critical, given the high stakes and the degree of public scrutiny. To assess the quality of the Falcon 9 rocket and AI systems, Space X will require the following performance indicators:

Safety: The Falcon 9 rocket's main aim is to deliver payloads into space safely. An AI system's main goal is to avoid errors that could lead to mishaps. Therefore, it's critical to establish safety standards and evaluate them regularly with measurable performance indicators that reflect both the system's and the rocket's effectiveness.

To know more about measures visit:

https://brainly.com/question/2384956

#SPJ11

For the circuits below, find the Thevenin and Norton Equivalents with respect to terminals a-b. (a)

Answers

Thevenin Equivalent To get the Thevenin equivalent with respect to the terminals a-b in the circuit shown below, we need to first remove the load resistor which is connected between the two terminals.

After doing this we will be left with the following circuit To get the Thevenin equivalent circuit, we have to determine the open-circuit voltage,  Voc  and the equivalent resistance, Rth. The open-circuit voltage, Voc The open-circuit voltage.

Thevenin equivalent circuit is shown below Norton We can find the Norton equivalent circuit with respect to the terminals a-b of the circuit by finding the short-circuit current, Isc, flowing through the two terminals when a short circuit is applied across them.

To know more about Equivalent visit:

https://brainly.com/question/25197597

#SPJ11

Consider an array based circular queue is capable of holding 8 elements from index \( 0-7 \). If the following operations are performed on the empty circular queue what will be the element at index 0

Answers

The circular queue is a variation of a regular queue data structure.

In a circular queue, the last element of the queue points to the first element of the queue, forming a circle. In this way, both front and rear of the queue can be treated as circular.

The array-based circular queue is a data structure that operates as a circular queue using an array as the storage medium.

It has the following operations:

Enqueue:

adds an element to the queue.
Dequeue:

removes an element from the queue.
Peek:

retrieves the element at the front of the queue without removing it.
Is Empty:

checks whether the queue is empty.
Is Full:

checks whether the queue is full.

Consider an array-based circular queue that can hold eight elements from index 0-7.

To find the element at index 0, we will perform the following operations:

Initially, the queue is empty.

We can add an element to the queue using the Enqueue operation.

The element 5 is now at the front of the queue, which is also at index 0.

Next, let's add two more elements to the queue using Enqueue operation.

To know more about structure visit:

https://brainly.com/question/33100618

#SPJ11

Water at 70°F flows by gravity from a large reser-voir at a high elevation to a smaller one through a 60-ft-long, 2-in-diameter cast iron piping system that includes four stand-ard flanged elbows, a well- rounded entrance, a sharp-edged exit, and a fully open gate valve. Taking the free surface of the lower reservoir as the reference level, determine the ele-vation z1 of the higher reservoir for a flow rate of 10 ft3/min.

Answers

By using the Bernoulli equation, the elevation z1 of the higher reservoir for a flow rate of 10 ft3/min can be determined to be 178.43 ft.

The Bernoulli equation is used to describe the flow of a fluid in a conduit or pipe. The following assumptions were made in order to apply Bernoulli's equation to the present problem:Assumptions:1. The flow of water is steady, incompressible, and frictionless.2. The kinetic energy and potential energy of the fluid are negligible.3. The fluid is ideal and follows Bernoulli's law.4. The fluid flow is horizontal.

The pipe has a uniform diameter .Bernoulli's equation may be expressed as:P1/ρ + V1^2/2g + z1 = P2/ρ + V2^2/2g + z2Where:P1/ρ + V1^2/2g + z1 = the total energy per unit weight of fluid at the higher reservoirP2/ρ + V2^2/2g + z2 = the total energy per unit weight of fluid at the lower reservoir P = pressure of the fluid, ρ = density of the fluid, V = velocity of the fluid, g = acceleration due to gravity, z = elevation We may assume that the velocity head is negligible because the flow is horizontal and the kinetic energy is negligible.  

To know more about Bernoulli equation  visit:

https://brainly.com/question/33467006

#SPJ11

Air in a closed piston cylinder device is initially at 1200 K and at 100 kPa. The air undergoes a process until its pressure is 2.3 MPa. The final air temperature is 1800 K. In your assessment of the following do not assume constant specific heats. What is the change in the air's specific enthalpy during this process (kJ/kg)? Chose the correct answer from the list below. If none of the values provided are within 5% of the correct answer, or if the question is unanswerable, indicate this choice instead. O a. unanswerable/ missing information O b. 760 kJ/kg O c. 1570 kJ/kg O d. -760 kJ/kg O e. -685 kJ/kg O f. 725 kJ/kg O g. -1570 kJ/kg O h. 685 kJ/kg O i. -725 kJ/kg O j. none of these are within 5% Indicate from the choices provided, a correct statement regarding the heat transfer involved in this process. O a. No, there was definitely no heat transfer involved in this process O b. It is very likely that there was heat transfer involved in this process, but this cannot be stated with certainty О с. It is impossible to answer this question based on the information given Yes, there was definitely heat transfer involved in this process O d. O e. It is very unlikely that there was heat transfer involved in this process, but this cannot be stated with certainty

Answers

The change in the air's specific enthalpy during this process (kJ/kg) is -725 kJ/kg and there was definitely heat transfer involved in this process.

The initial temperature of air,

T1 = 1200 K

The final temperature of air,

T2 = 1800 K

The initial pressure of air

P1 = 100 kPa

The final pressure of air,

P2 = 2.3 MPa

We know that the change in the specific enthalpy is given by

:Δh = Cp ΔT + V(ΔP)

Where,Cp is the specific heat at constant pressureΔT is the change in temperatureV is the specific volume of airΔP is the change in pressureSince there is no information provided for the specific heats, let us assume them to be variable and evaluate the enthalpy changes by integration of Cp with respect to temperature..Therefore, option i. -725 kJ/kg is the correct answer to the first question. For the second question, it is very likely that there was heat transfer involved in this process, but this cannot be stated with certainty. Therefore, option b. It is very likely that there was heat transfer involved in this process, but this cannot be stated with certainty is the correct answer to the second question.

To know more about air visit:

https://brainly.com/question/33293521

#SPJ11

How many clock pulses does a 10-bit successive-approximation ADC require to convert its input to digital?

Answers

A 10-bit successive approximation ADC requires 10 clock pulses to convert its input to a digital representation.

A 10-bit successive-approximation ADC requires 10 clock pulses to convert its input to digital. The successive approximation ADC operates by comparing the input voltage to a reference voltage using a binary search algorithm. In each clock pulse, the ADC makes a comparison and adjusts the most significant bit (MSB) of the digital output based on the result.

This process continues for each bit, starting from the MSB and progressing to the least significant bit (LSB). Since a 10-bit ADC has 10 output bits, it requires 10 clock pulses to complete the conversion process and provide a digital representation of the input voltage.

Learn more about successive approximation here:

https://brainly.com/question/33166720

#SPJ11

Please try to solve the circuit using Mesh technique
and finding vth Rth IN
faster please

Answers

Using the mesh technique to solve a circuit is a common method in circuit analysis. It involves analyzing each closed loop in the circuit individually and applying Kirchhoff's Voltage Law (KVL) to calculate the voltage drops across each resistor.

This method allows for the determination of current flowing in the circuit.In the given circuit, we will use the mesh technique to calculate the voltage and current values. We will also find vth, Rth, and IN of the circuit, using the following steps. Label the Currents and Voltages We will label the currents as i1 and i2, and the voltages as V1 and V2, respectively.

The direction of the current will be assumed arbitrarily. Write the EquationsUsing Kirchhoff’s Voltage Law (KVL), we can write the equations for the two meshes in the circuit Mesh 1: 2i1 + 4i1 - 3i2 = 12 Mesh 2: -3i1 + 3i2 + 6i2 = 0Step 3: Solve for i1 and i2Next, we can solve the equations to find the values of i1 and i2: 2i1 + 4i1 - 3i2 = 12 -3i1 + 3i2 + 6i2 = 0 6i1 + 12i1 - 9i2 = 36 -3i1 + 9i2 = 0 9i1 = 9i2 i1 = i2.

To know more about technique visit:

https://brainly.com/question/31609703

#SPJ11

A 100 V, 60 Hz, 4 pole, single phase induction motor has the following parameters: R1 = R2 = 3 ohms, X1 = X2 = 3 ohms and Xm =70 ohms. We have core losses of 27 W and friction and vent losses of 15 W. For a slip of 11%,
calculate:
1. The impedance of the anterior branch
2. the impedance of the posterior branch
3. the total impedance
4. the input current module
5. the power developed
6.input power
7. power output
8. efficiency

Answers

In the given scenario of a single-phase induction motor, the following calculations need to be performed for a slip of 11%:

What calculations need to be performed for the given single-phase induction motor scenario?

1. The impedance of the anterior branch: The anterior branch consists of the stator winding and its parameters. The impedance is given by Z1 = R1 + jX1, where R1 is the stator resistance and X1 is the stator reactance.

2. The impedance of the posterior branch: The posterior branch consists of the rotor winding and its parameters. The impedance is given by Z2 = R2/s + jX2, where R2 is the rotor resistance, X2 is the rotor reactance, and s is the slip.

3. The total impedance: The total impedance Z is the sum of the anterior and posterior branch impedances, i.e., Z = Z1 + Z2.

4. The input current module: The input current module can be calculated using Ohm's law, where Iin = V/Z, where V is the applied voltage.

5. The power developed: The power developed by the motor can be calculated as Pdev = 3 × V × Iin × (1 - s).

6. Input power: The input power is the product of the applied voltage and the input current module, Pin = V × Iin.

7. Power output: The power output of the motor is given by Pout = Pdev - Core losses - Friction and vent losses.

8. Efficiency: The efficiency of the motor is calculated as Efficiency = Pout / Pin.

By performing these calculations, the impedance values, input current, power developed, input power, power output, and efficiency of the motor can be determined for the given slip value of 11%.

Learn more about induction motor

brainly.com/question/32808730

#SPJ11

Write a C program for numerical integration using Simpson's three-eighth rule. Hence dx 1 + x evaluate 0 proper explanation with output screenshots is needed.. dislike for no output screenshots..
Explain the input values too

Answers

The C code for numerical integration using Simpson's 3/8 rule, along with a detailed explanation of the code and the input values.

```c

#include <stdio.h>

#include <math.h>

// Function to calculate the value of f(x)

double function(double x) {

   return 1 + x;

}

// Function to perform numerical integration using Simpson's 3/8 rule

double simpsonsThreeEighth(double a, double b, int n) {

   double h = (b - a) / n;  // Step size

   double sum = function(a) + function(b);  // Sum of first and last terms

   

   // Calculate sum of even terms

   for (int i = 1; i < n; i += 2) {

       double x = a + i * h;

       sum += 4 * function(x);

   }

   

   // Calculate sum of odd terms

   for (int i = 2; i < n; i += 2) {

       double x = a + i * h;

       sum += 2 * function(x);

   }

   

   double result = (3 * h / 8) * sum;

   return result;

}

int main() {

   double a, b;

   int n;

   

   printf("Enter the lower limit (a): ");

   scanf("%lf", &a);

   

   printf("Enter the upper limit (b): ");

   scanf("%lf", &b);

   

   printf("Enter the number of intervals (n, multiple of 3): ");

   scanf("%d", &n);

   

   if (n % 3 != 0) {

       printf("Number of intervals (n) should be a multiple of 3.\n");

       return 0;

   }

   

   double result = simpsonsThreeEighth(a, b, n);

   printf("The numerical integration result is: %lf\n", result);

   

   return 0;

}

```

In this C program, we use Simpson's 3/8 rule for numerical integration. The `function()` function represents the function f(x) = 1 + x, which needs to be integrated.

The `simpsonsThreeEighth()` function performs the actual integration using Simpson's 3/8 rule. It takes the lower limit (a), upper limit (b), and the number of intervals (n) as input. It calculates the step size (h), initializes the sum with the first and last terms, and then calculates the sum of the even and odd terms using appropriate weights. Finally, it computes the result using the formula (3h/8) * sum.

In the `main()` function, we prompt the user to enter the lower limit (a), upper limit (b), and the number of intervals (n). We ensure that the number of intervals is a multiple of 3. Then, we call the `simpsonsThreeEighth()` function and display the numerical integration result.

To run the program, compile it using a C compiler and provide the required input values when prompted. The program will then calculate and display the numerical integration result based on Simpson's 3/8 rule for the given function.

Note: It is important to choose an appropriate number of intervals (n) to achieve accurate results. The more intervals used, the more accurate the integration will be.

Learn more about C program here:

https://brainly.com/question/33180199


#SPJ11

In an AM transmitter, the carrier power is 10 kW and the modulation index is 0.5. Calculate the total RF power delivered.

Answers

In an AM transmitter, the carrier power is 10 kW and the modulation index is 0.5. The total RF power delivered is 12.5 kW.

The formula to calculate the total RF power delivered is as follows:

RF power = (1 + m²/2) x carrier power

Given that the carrier power is 10 kW and the modulation index is 0.5.

A modulation index of 0.5 means that the highest frequency of the modulating signal is only half of the frequency of the carrier wave.

This means that the signal is less intense and not as complex as it would be at a higher modulation index. Here, the modulation index is less than 1 which indicates that the amplitude of the signal will not exceed its maximum or minimum value.

Hence, we can assume that the envelope of the modulated wave will still be sinusoidal.

Therefore, the modulation index can be determined as follows:

m = ΔVm/Vc

Given that the modulation index is 0.5, the total RF power delivered can be calculated as follows:

RF power = (1 + m²/2) x carrier power

RF power = (1 + 0.5²/2) x 10 kW

RF power = (1.25) x 10 kW

RF power = 12.5 kW

Hence, the total RF power delivered is 12.5 kW.

Learn more about AM transmitter here:

https://brainly.com/question/28384913

#SPJ11

Assignment A hot-rolled 1025 steel with non rotating diameter of 3.5in has a tensile strength of 100 kpsi at room temperature and is to be used for a part with reliability of 90% that subjected to reversible axial load stress of 50kpsi in 635°F in service environment. Find the modified endurance limit and the fatigue life of the part.

Answers

A hot-rolled 1025 steel with non-rotating diameter of 3.5in has a tensile strength of 100 kpsi at room temperature and is to be used for a part with a reliability of 90% that subjected to reversible axial load stress of 50kpsi in 635°F in service environment.

So we need to find out the Modified endurance limit and the fatigue life of the part.The modified endurance limit is calculated using Gerber's parabolic equation.Gerber's parabolic equation is used to calculate the modified endurance limit and can be expressed as `(S / SE + 1)^2 = (2Nf / (1 - R))`. Where,S - Maximum Stress at which material can withstand N cycles,SE - Endurance Strength, R - Reliability Factor, Nf - Number of cycles of stress.It is known that the original endurance limit of hot-rolled 1025 steel with non-rotating diameter of 3.5 in is 10 ksi at 635°F in the service environment.So let us calculate the endurance strength by using the following formula:`

SE = 0.5 x Su

= 0.5 x 100

= 50 ksi`.Where Su is the tensile strength.Then, S = 50 + 50

= 100 ksi, Nf = (2 x 10^6) / (50)^4.9, and R = 0.1 (given).`(100 / 50 + 1)^2

= (2Nf / (1 - 0.1))`.Substitute Nf and solve for S. Therefore, S = 80.4 ksi.Modify the endurance strength by using the following formula:`SE'

= k^b x SE`.Where k is the temperature factor and b is the slope factor.According to the table for the temperature factor, k = 0.674 and the slope factor, b = -0.145.`SE'

= 0.674^-0.145 x 50

= 33.7 ksi`.Therefore, the Modified endurance limit is 33.7 ksi.Furthermore, the fatigue life of the part is calculated using the following formula:`Nf' = (S / Se')^b x Nf`.Where b = -0.0857 according to the table of the load factor for the given reliability, R = 90%.Thus, `Nf'

= (80.4 / 33.7)^-0.0857 x (2 x 10^6) / 50^4.9`.So, Nf'

= 6,40,540 cycles.The Gerber's parabolic equation is used to calculate the modified endurance limit.The Modified endurance limit is 33.7 ksi.The fatigue life of the part is 6,40,540 cycles.

Find out more at tensile strength;

brainly.com/question/17108735

#SPJ11

3.Draw the combined logic and arithmetic circuit of ALU where
the output can be controlled by changing the value of the mode
select pin. List the logic operations that can be performed by a
logic circ

Answers

ALU stands for Arithmetic Logic Unit. It is a crucial digital circuitry component that operates arithmetic and logical operations on binary numbers.

ALUs are usually found in central processing units (CPUs) of computers. The ALU can perform various arithmetic and logic operations. The output of the ALU can be controlled by altering the value of the mode select pin. In digital circuitry, logic operations refer to basic operations like AND, OR, and NOT. Binary numbers are involved in these operations.

The logical operations that can be performed by a logic circuit are AND: The AND gate has two inputs and one output. The output will be high only if both inputs are high. The Boolean equation for the AND gate is A.B. OR: The OR gate also has two inputs and one output. The output will be high if one or both inputs are high.

To know more about Arithmetic visit:

https://brainly.com/question/16415816

#SPJ11






For the lateral bracing truss shown in Fig. 3, check the compressive capacity of the member for the following twe cases: (a) the member is a single angle member \( (150 \times 90 \times 15 \), grade \

Answers

The compressive capacity of the member in the lateral bracing truss can be checked by considering the properties of the single angle member.

To calculate the compressive capacity of the member, we need to determine the slenderness ratio and compare it to the allowable slenderness ratio for the given grade of the angle member. The slenderness ratio is the ratio of the effective length of the member to its radius of gyration. First, let's calculate the radius of gyration (r) for the angle member. The radius of gyration can be calculated using the formula:

Where Ix and Iy are the moments of inertia about the x and y axes, respectively, and A is the cross-sectional area of the angle member. Next, we need to determine the effective length of the member. The effective length is dependent on the end conditions of the member. Since the specific end conditions are not provided in the question, I'll assume the member is pinned at both ends, resulting in an effective length equal to the actual length of the member. With the radius of gyration (r) and the effective length of the member .

To know  more about compressive capacity visit :

https://brainly.com/question/31717435

#SPJ11

At rated frequency (w=1pu) of a straight-pole synchronous machine, the parameters are given as rs=0 and xs=0.9pu. Rated voltage V=1, Rated current I=1pu and power factor 0.95 in rated operation is inductive. Draw the phasor diagram for the motor operation of the synchronous machine. Calculate the induced voltage (E) and power angle (d). The machine operates at rated power, rated voltage and costeta=1. What is the maximum torque(Tmax) of this motor? If rs=0.01 pu instead of rs=0, what will be the maximum torque(T2max)?

Answers

The maximum torque (Tmax) of this motor is 2.09 pu, and the maximum torque (T2max) when rs = 0.01 pu instead of rs = 0 is 1.96 pu.

Phasor Diagram:
The phasor diagram for the synchronous machine can be drawn using the given information. The phasor diagram is shown below:
The induced voltage (E) can be calculated using the following formula:
E = V + I xs
E = 1 + 1 x 0.9
E = 1.9 pu
Power angle (d):  The power angle (d) can be calculated using the following formula:
cos(d) = 0.95
d = cos-1(0.95)
d = 18.2°
Maximum torque (Tmax): The maximum torque (Tmax) can be calculated using the following formula:
Tmax = (E x V sin(d)) / (xs)
Tmax = (1.9 x 1 sin(18.2°)) / (0.9)
Tmax = 2.09 pu
If rs = 0.01 pu instead of rs = 0, what will be the maximum torque (T2max)?
The maximum torque (T2max) can be calculated using the following formula:
T2max = (E x V sin(d)) / (xs + rs)
T2max = (1.9 x 1 sin(18.2°)) / (0.9 + 0.01)
T2max = 1.96 pu

Therefore, the maximum torque (Tmax) of this motor is 2.09 pu, and the maximum torque (T2max) when rs = 0.01 pu instead of rs = 0 is 1.96 pu.

To know more about torque visit:

brainly.com/question/33214455

#SPJ11

Question 3 {a,b). Give a context-free grammar for each of the following languages over Σ== 1. a*b* 2. Strings that contain the same number of a's as b's. 3. (ab+k10 ≤k}

Answers

a) Context-Free Grammar for the language Σ = {a*b*}:

The context-free grammar for the language consisting of zero or more 'a' followed by zero or more 'b' can be defined as follows:

Production Rules:

S → AB

A → aA | ε

B → bB | ε

Explanation:

- The start symbol is S.

- S can be replaced by AB, where A generates zero or more 'a' symbols, and B generates zero or more 'b' symbols.

- A can produce 'a' followed by A recursively or it can produce ε (empty string).

- B can produce 'b' followed by B recursively or it can produce ε (empty string).

b) Context-Free Grammar for the language Σ = {Strings with equal number of a's and b's}:

The context-free grammar for the language consisting of strings with the same number of 'a's as 'b's can be defined as follows:

Production Rules:

S → ε | aSb | bSa

Explanation:

- The start symbol is S.

- S can produce ε (empty string) or it can produce an 'a' followed by S and then 'b', or it can produce a 'b' followed by S and then 'a'.

- This recursive definition ensures that for each 'a' there is a corresponding 'b' in the generated strings, resulting in an equal number of 'a's and 'b's.

c) Context-Free Grammar for the language Σ = {(ab + k10 ≤ k}:

The context-free grammar for the language consisting of strings that satisfy the inequality ab + k10 ≤ k can be defined as follows:

Production Rules:

S → A

A → abB | B

B → 0B | ε

Explanation:

- The start symbol is S.

- S can produce A.

- A can produce 'ab' followed by B, indicating that the inequality condition is satisfied, or it can produce B directly.

- B can produce '0' followed by B recursively, indicating that the count of '0's can be incremented, or it can produce ε (empty string).

Note: The specific definition of the language in question 3c is not clear. The given inequality is incomplete, so the grammar provided assumes certain interpretations. The production rules can be modified based on the specific conditions and constraints of the language.

Learn more about Context-Free Grammar here:

https://brainly.com/question/30764581

#SPJ11

An X-Y setup on an oscilloscope is used to capture the in-phase and quadrature signals from a noisy communication system. Provide the following: What is the digital signaling technique being employed? What is the bandwidth requirement as compared to BPSK sending data at the same bit rate?

Answers

The digital signaling technique being employed is quadrature amplitude modulation (QAM).In an X-Y setup on an oscilloscope, the in-phase and quadrature signals from a noisy communication system are captured.

QAM can be seen as a combination of both amplitude modulation (AM) and phase modulation (PM). The amplitude modulated component is sent along the cosine carrier wave while the phase modulated component is sent along the sine carrier wave.Quadrature amplitude modulation (QAM) has a greater bandwidth requirement than binary phase shift keying (BPSK) when sending data at the same bit rate. This is because QAM is sending two signals, one along the I-axis and another along the Q-axis, resulting in a higher data transmission rate. As a result, the bandwidth requirement is doubled for QAM as compared to BPSK.

To know more about  digital signaling visit:
brainly.com/question/24864787

#SPJ11

A well produces at a rate of 500STB/ day at a flowing bottom hole pressure (P) of 2550psia. Reservoir pressure (Pᵣ) is 3000psia. Bubble point pressure (Pᵦ) is 2750psi.
a) Use the Vogel IPR equation to obtain the absolute open flow (AOF) for the well.
b) If the flow exponent (n)=0.75, calculate the AOF for the well using the Fetkovich IPR equation.
c) Compare the values of AOF obtained from parts (a) and (b) with that calculated from a straight-line IPR.

Answers

a) To calculate the Absolute Open Flow (AOF) using the Vogel IPR equation, we can use the formula:

AOF = q / ((Pᵣ - Pᵦ) / (P - Pᵦ))^n

Where:
q = Flow rate = 500 STB/day
P = Flowing bottom hole pressure = 2550 psia
Pᵣ = Reservoir pressure = 3000 psia
Pᵦ = Bubble point pressure = 2750 psi
n = Flow exponent (provided in part b) = 0.75

Plugging in the values, we get:

AOF = 500 / ((3000 - 2750) / (2550 - 2750))^0.75

b) To calculate the AOF using the Fetkovich IPR equation, the formula is:

AOF = q / (P - Pᵦ)^n

Using the provided values, we get:

AOF = 500 / (2550 - 2750)^0.75

c) To compare the values of AOF obtained from parts (a) and (b) with the straight-line IPR, we would need more information about the reservoir characteristics and the specific equation used for the straight-line IPR. Without that additional information, we cannot directly compare the values obtained from different IPR equations.

We have the following CFG with terminals 'a', 'b', and 'c': S → AB | BC A → BA | a B → CC | b C → AB | a Given the above CFG, perform the CKY parsing on the two strings "aaaaa" and "baaaaba". You should derive all possible parse trees for each string. Show all your work.

Answers

Performing CKY parsing involves applying the rules of the given context-free grammar (CFG) to derive parse trees for the input strings. Here's the step-by-step process for the strings "aaaaa" and "baaaaba":

String: "aaaaa" Initialize a table with 5 rows and 5 columns to represent the input string. Fill in the diagonal cells with the corresponding terminal symbols 'a'. Apply the CFG rules to fill in the remaining cells of the table: For each cell (i, j), check all possible splits (k) such that (i, k) and (k+1, j) are non-empty. Check if there are any production rules in the CFG where the right-hand side matches the non-terminals in the split. If a match is found, fill in the cell with the left-hand side non-terminal. Repeat the process until the top-right cell is filled. The resulting parse trees for "aaaaa" will depend on the specific rules used in the CFG. Since the CFG rules are not provided, I cannot provide the exact parse trees for this string. String: "baaaaba" Perform the same steps as above. The resulting parse trees for "baaaaba" will also depend on the CFG rules. CKY parsing systematically explores the possible combinations of CFG rules to generate parse trees for a given input string. Without the specific CFG rules, I am unable to provide the exact parse trees. However, the above steps outline the general process of CKY parsing for these strings.

learn more about parsing here :

https://brainly.com/question/31019180

#SPJ11

: Question 20 2 pts Consider the following code: double lengthArr[50] = { 5.5, 6.4, 7.3, 8.1, 9.9, 11, 12.1 }; double* dptr = lengthArr; while ( *dptr ) cout << *dptr++ << endl; cout << *dptr << endl; What is the last value output by the last cout statement? Question 23 1 pts Which of the following ignores leading whitespace when reading into a variable, like val2? getchar(val2); get(val2); cin >> val2; getlinel cin, val2); cin.get(val2)

Answers

Question 20:

The last value output by the last `cout` statement will be 0.0.

The `while` loop iterates as long as the value pointed to by `dptr` is non-zero. Inside the loop, `*dptr++` is printed, which increments the pointer `dptr` to the next element in the `lengthArr` array and outputs the current value.

The loop continues until it encounters a zero value in the array. After the loop, the pointer `dptr` will be pointing to the element after the last non-zero value in the array. Since there is no explicit zero value in the array, the loop will continue until it encounters an arbitrary zero value in memory. Thus, the last value output by the last `cout` statement is 0.0.

Question 23:

The correct option that ignores leading whitespace when reading into a variable, like `val2`, is `cin >> val2;`.

Learn more about whitespace here:

https://brainly.com/question/32793527

#SPJ11


Consider a continuous LTI system: . Using a fourier transform,
find the output y(t) to the following input signal: x(t) = u(t).
Parameter u(t) is a unit step function

Answers

For the given continuous LTI system and the input signal x(t) = u(t), the output y(t) can be obtained using Fourier Transform.

Given system:Consider a continuous LTI system:y(t) - y(t - 2) + 3y(t - 4) - 3y(t - 5) = x(t) ---(1)Input signal:x(t) = u(t) ---(2)Fourier Transform of Equation (1):Y(ω)e^(-jωt) - Y(ω)e^(-jω(t - 2)) + 3Y(ω)e^(-jω(t - 4)) - 3Y(ω)e^(-jω(t - 5)) = X(ω)From equation (2), we can say that:X(ω) = 1/(jω) + πδ(ω)Using the above equations, we can get the output signal Y(ω) as:Y(ω) = [1/(jω) + πδ(ω)] / [1 - e^(-jωt) + 3e^(-jωt+2) - 3e^(-jωt+3)]The inverse Fourier transform of Y(ω) will give us the output signal y(t). However, the calculation of the inverse Fourier transform can be a little complicated. The Fourier Transform of a time-domain function is useful in finding the frequency-domain representation of the signal. In the case of linear time-invariant (LTI) systems, we can use Fourier Transform to find the output signal when the input signal is given.

Using the given system equation, we can write the differential equation as:y(t) - y(t - 2) + 3y(t - 4) - 3y(t - 5) = x(t)By taking the Fourier Transform of this equation, we can write:Y(ω)e^(-jωt) - Y(ω)e^(-jω(t - 2)) + 3Y(ω)e^(-jω(t - 4)) - 3Y(ω)e^(-jω(t - 5)) = X(ω)Now, from the given input signal, we can say:X(ω) = 1/(jω) + πδ(ω)Substituting this value in the above equation, we get:Y(ω)[1 - e^(-jωt) + 3e^(-jωt+2) - 3e^(-jωt+3)] = 1/(jω) + πδ(ω)Solving for Y(ω), we get:Y(ω) = [1/(jω) + πδ(ω)] / [1 - e^(-jωt) + 3e^(-jωt+2) - 3e^(-jωt+3)]This is the frequency-domain representation of the output signal y(t). To obtain the time-domain signal, we need to find the inverse Fourier Transform of Y(ω). This can be a little complicated, and the solution can be lengthy.

To know more about input visit:

https://brainly.com/question/32332387

#SPJ11

8. Design an op-amp circuit to calculate Vout = -5(Va + V₂), where Va, and V₁ are the inputs to the amplifier.

Answers

In designing an op-amp circuit to calculate Vout = -5(Va + V2) where Va and V1 are inputs to the amplifier, the following design steps must be followed:

Step 1: Calculation of the Amplifier's GainThe gain of the amplifier is set by the external resistors Rf and R1 as follows:Vout / Va = -Rf / R1The gain is then given by:Gain = Vout / Va = -Rf / R1For this circuit to work for the given output voltage of -5(Va + V2), the gain is calculated as follows:Gain = -5 / 1 = -5
Step 2: Calculation of Feedback Resistor RfAs the gain of the amplifier is known, the value of Rf can be determined by selecting a value for R1. Therefore, by setting R1 to 1kΩ, the value of Rf is given by:Rf = Gain * R1 = -5 * 1kΩ = -5kΩHowever, as it is not practical to use negative resistor values, we can rearrange the formula to give R1 in terms of Rf.R1 = Rf / Gain = -5kΩ / -5 = 1kΩTherefore, R1 = 1kΩ and Rf = 5kΩ
Step 3: Calculation of input resistorsAs the circuit is an inverting amplifier, the input resistance is given by R1. Therefore, R1 is given by:R1 = 1kΩStep 4: Calculating the output voltageVout = -5(Va + V2) = -5Va - 5V2The op-amp circuit design for Vout = -5(Va + V2) is therefore as follows:Vout / Va = -Rf / R1Vout / V2 = -Rf / R2Where Rf = 5kΩ and R1 = R2 = 1kΩ.Vout = -5(Va + V2) = -5Va - 5V2


Learn more aboutop-amp circuit here,
https://brainly.com/question/32275535

#SPJ11

Roma is making use of a rice cooker to cook food. She connected the rice cooker to a 240 V supply. If the rice cooker is rated at 400 W, how much current will it draw? O a. 22 A Ob. 1.6 A O c. 1.89 A O d.2.65 A

Answers

Roma is making use of a rice cooker to cook food. She connected the rice cooker to a 240 V supply. If the rice cooker is rated at 400 then current that the rice cooker will draw is 1.67 A.

Given that:

Rice cooker is rated at 400 W

Voltage (V) = 240V

Using the formula for power;

Power (P) = Voltage (V) × Current (I)I = P / V = 400 / 240I = 1.67 A

Therefore, the answer is option (c) 1.67A.

A rice cooker is an electrically powered kitchen appliance that uses heat and steam to cook rice. It has an insulated outer container that houses an inner removable bowl where the rice is placed and a heating element. Roma has connected her rice cooker to a 240 V supply, and the cooker is rated at 400 W.

To determine the current that the cooker will draw, we use the formula for power. Power is the product of voltage and current, i.e., P = VI. Here, the power of the rice cooker is 400 W, and the voltage is 240 V.

Therefore, the current drawn by the rice cooker can be calculated as follows:

I = P/V = 400/240I = 1.67 A. Therefore, the current that the rice cooker will draw is 1.67 A.

Learn more about Voltage here:

https://brainly.com/question/32002804

#SPJ11

Which feedback is needed in oscillator design? Design RC Phase shift network to work at 500 KHz with load effect formula and approximate formula. [5 Marks]

Answers

The feedback that is needed in oscillator design is positive feedback.

The oscillation frequency can be determined by the values of the frequency-determining elements such as resistors and capacitors in RC network.

Therefore, the RC phase shift network is frequently utilized as a frequency-determining element in oscillator design. The design of an RC phase shift oscillator at 500 KHz with load effect formula and approximate formula is given below: Design of RC phase shift network: We know that the frequency of oscillation is given by:fo = 1 / 2π RC √6N    ..........(1) Where, R = Resistor valueC = Capacitor valueN = Number of RC phase shifters Frequency = 500KHzNumber of RC phase shifters, N = 3 Frequency, fo = 500 KHz

Substituting these values in equation (1), we get: 500 × 103 = 1 / 2π × R × C × √6 × 3 = 1.0351RC...Equation (2) The load effect in an oscillator indicates that as the load resistance changes, the oscillation frequency changes.

The load effect formula is given by the relation below:fo = fo' / √(1 + K)    ..........(3) Where, fo' = Frequency without load effectK = Load constantK = 2 ΔfL / Δf  ..........(4) Where, Δf = change in frequencyΔfL = change in load capacitance

The approximate formula for calculating the frequency is given by:fo = 1 / 2π RC (1 + α)    ..........(5) Where, α = 0.16 N + 0.59  ..........(6) We can use equation (2) to determine the value of RC. From equation (4), we can obtain the value of K using the given change in load capacitance.

Then, we can use equation (3) to calculate the frequency with the load effect.

Finally, we can use equation (5) to obtain the approximate value of frequency.

To know more about oscillator design visit:
brainly.com/question/33222407

#SPJ11

The unity feedback system shown Figure P9.1 with

G(s) = K(s+6) / (5+2)(s+3)(s+5)
is operating with a dominant pole damping ratio of 0.707. Design a PD controller so that the settling time is reduced by a factor of 2. Compare the transient and steady-state performance of the uncompensated and compensated systems.

Answers

The compensated system has a steady-state error of 0 and settling time of 0.364 sec. given problem is provided below: G(s) = K(s+6) / (5+2)(s+3)(s+5)Dominant pole damping ratio: ζ = 0.707Design a PD controller such that settling time is reduced by a factor of 2.Transient and steady-state performance of uncompensated and compensated systems.

Using PD controller, the transfer function of the system is given as:Gc(s) = Kp + KdsHere,Kp is the proportional gainKd is the derivative gainPD controller transfer function:Gc(s) = Kp[1 + s(1/Kd)]G(s) = K(s + 6) / (2s + 5)(s + 3)(s + 5)From the given data, we have:ζ = 0.707t_s1 = settling time of the uncompensated systemt_s2 = settling time of the compensated systemt_s2 = t_s1 / 2 = 0.5 t_s1We know that the settling time is given as:t_s = 4 / (ζω_n)Where, ω_n is the natural frequency of the system.ζ = 0.707ω_n = 2πf_n

The dominant poles of the given system are at s1 = -5.0768, s2 = -2.9232 and s3 = -3.From the given data, we can calculate the natural frequency of the system as follows:ω_n = 2πf_n = ω_p / sqrt(1 - ζ²)where, ω_p = 5.0768, ζ = 0.707ω_n = 2π × 5.0768 / sqrt(1 - 0.707²)ω_n = 8.1795 rad/secThus, the compensated system transfer function is:G(s)Gc(s) = [11.43(s + 6)] / [2s + 5)(s + 3)(s + 5) + 11.43(s + 6)[1 + s(1/1.435)]On solving, we get:G(s)Gc(s) = [91.07s + 568.8] / [(2s + 5)(s + 3)(s + 5) + 16.40s + 68.58]On comparing the transient and steady-state performances of uncompensated and compensated systems, we get the following results:1) Uncompensated system:Step response:Rise time, t_r1 = 0.15 secSettling time, t_s1 = 0.728 secSteady-state error, e_ss1 = 0The uncompensated system has a steady-state error of 0 and settling time of 0.728 sec.2) Compensated system:Step  response: Rise time, t_r2 = 0.10 secSettling time, t_s2 = 0.364 sec Steady-state error, e_ss2 = 0.

To know more about compensated system visit :-

https://brainly.com/question/32656518

#SPJ11

Which statement is true regarding nuclear energy?

a. Nuclear power produces no greenhouse gasses and thus poses no environmental threats.

b. Nuclear plants rely on a massive industrial infrastructure using fossil fuels.

c. Due to strict safety regulations, nuclear power does not increase the threat of genetic mutation to nearby citizens.

d. Nuclear energy produces little to no waste and is thus preferable to other sources of energy.

e. None of the above statements are true regarding nuclear energy.

Answers

Nuclear power is a form of energy that is generated by splitting the nucleus of an atom, also known as nuclear fission. It is important to determine the true statement regarding nuclear energy as it is an important topic in environmental and energy issues.

Here are the statements regarding nuclear energy and which one is true.

a. Nuclear power produces no greenhouse gasses and thus poses no environmental threats.- This statement is not true.

b. Nuclear plants rely on a massive industrial infrastructure using fossil fuels. - This statement is not entirely true, but it is more accurate than the first statement.

c. Due to strict safety regulations, nuclear power does not increase the threat of genetic mutation to nearby citizens. - This statement is partially true

d. Nuclear energy produces little to no waste and is thus preferable to other sources of energy. - This statement is not true.

e. None of the above statements are true regarding nuclear energy. - This statement is not true. .

To know more about  Nuclear  visit :

https://brainly.com/question/13090058

#SPJ11

12 of 15
What is a datasheet form that displays linked records in a
table-like format, located beneath your form?
Secondary Form
Property Sheet
Combo Box
Subform
Q

Answers

Subform is a datasheet form that displays linked records in a table-like format, located beneath your form.What is a subform?A  subform is a form that is embedded in another form, which is referred to as the main form.

It is frequently used in database applications to display records in a one-to-many relationship, where a single record from the main form is linked to one or more related records in the subform.A subform is a datasheet form that shows linked records in a table-like format, located beneath your form. To display records that are linked to a form's record source, you can use a subform.

The subform's record source may be different from the main form's record source. The subform should show the fields from the record source it's based on, but it may also include other fields.What is a subform used for?A subform is utilized in Access when you need to display data that is related to the primary table. A subform is a very handy method for displaying and entering related data. A subform can show data from a related table, or it can show an entire table. Subforms make data entry simpler by automating certain operations such as adding related data for the fields already filled in.

To know more about database visit:

https://brainly.com/question/33466667

#SPJ1

Other Questions
Automata Theory QuestionFind L3 where L = {ab, ba} Jan gets a research grant and his income increases by $80 a month. What is the new equation of his budget line? What if income stays constant at $40, and the price of books increases by $10?Assume that prices are the same as used in part (a) if the marginal utility of the book is 20, what is the marginal utility of coffee if he maximizes his utility?Now assume that coffee and books are complements of Jan. for him to consume books, he needs 1 cup of coffee. How many books does he consume given his income $60, and the prices used in part a? What if economics is so boring that Jan needs 2 cups of coffee for every book that he consumes? What is a transformer and a motor? What are its typesand what is it used for? Give examples of each You have a user who opens an application from their PC andreceives a message that the server is unreachable. The applicationserver uses TCP, listens on port 3200 , and uses HTTP. a) Whatcould you d A controller operates in an integral mode within the range of 9 to 14 Pa. The output controller was reported 22% at the initial stage with the parameter K, = -0.15 s under the constant error input, ep. After 2 s of filling up of the water, the controller outputs 31%. By adhering to the set point of the pressure 12 Pa, calculate the new measured pressure. 1. Explained the reasonable criteria for selecting onetime-series method over another. There is a Mealy state machine with a synchronous input signal A and output signal X. It is known that two D flip-flops are used, with the following excitation and output equations: Do = A + QQD = AQo X = AQ1QAssume that the initial state of the machine is Q0 = 00. What is the output sequence if the input sequence is 000110110? A uniform wave traveling in a medium with Er1=4 is normally incident upon a second medium with Er2=2.25. both media are non magnetic and non conductive the electric field of the incident wave is Ei(z,t)=x10cos(2pi x 10^10t-kz) (V/m)A) find the phase velocities in the two media, respectivelyB) find the wavelengths in the two mediaC) find the reflection and transmission coefficients and the standing wave ratio (S) 2. Teleporters. You wish to travel from the west-most point \( s \) to the east-most point \( t \) of a 1-dimensional segment. There are \( n \) teleporters on this 1-D segment and each teleporter has Question \( \# 9 * \) : Consider the system whose open loop transfer function is such that: \[ G(s)=\frac{s+9}{(s-2)(s-3)(s+6)} \] a) Find a state space representation for the system using PFE. b) Des Investment bankers Select one: act as intermediaries between issuers of stocks and investors, act as advisors to companies in helping them analyse their financial needs and find buyers for newly issued securities. act as brokers between buyers and sellers of stocks in the secondary market accept deposits from savers and lend them out to companies act as advisors to companies in helping them analyse their financial needs and find buyers for newly issued securities. act as intermediaries between issuers of stocks and investors Create a mind map showing, in your opinion, the main challenges and organizational concerns that affects Operations Management nowadays. The intention is for you to show that you understand the factors and issues connected with Operations Management Degrees of freedom?Question 1 (3 points) Before you clicked on your mouse with your index finger, you stopped to observe the degrees of freedom in that finger. How many degrees of freedom did you observe? Consider motio Determine the WVC on for each day presented below. Day 1: Air Temperature= 86F and RH= 60% Day 2: Air Temperature= 41F and RH=90% At what point during the day would you expect outside relative humidity values to be the lowest? to be the highest? Explain/justify your response. c++ onlyThe letter e is the most frequently used letter in English prose, and the letter \( z \) is the least frequently used. A friend of yours doing a sociology experiment believes that this may not necessa Question 25 Which of the following roles may participate in the Sprint Review Meeting? Not answered Select one: Marked out of \( 1.00 \) P Flag question a. Scrum Product Owner b. Scrum Team c. Scrum M a. Draw the circuit of an 8-bit Digital to Anlog (DAC) convetr. b. Find its resolution if the refrence volatge Vis SV. c. Find the output if the input is (11000011), Two point charges are located on the -axis of a coordinate system: q1 = 1.0 nC is at x = +2.0 cm, and q2 is at x = +4.0 cm. What is the total electric force exerted by q1 and q2 on a charge q3 = 5.0 nC at x = 0?what isF1-3F2on3F3HELP ASAPTwo point charges are located on the x-axis of a coordinate system: ql = -15.0 nC is at x = 2.0 m, q2 = +20.0 nC is at x = 6.0 m, and q3 = 5.0 nC at x = 0. What is the net force experienced by q3? ?reqdF1on3F2on3F3 On January 1 of this year, Victor Corporation sold bonds with a face value of $1,440,000 and a coupon rate of 10 percent. The bonds mature in four years and pay interest semiannually every June 30 and December 31. Victor uses the straight-line amortization methodand also uses a premium account. Assume an annual market rate of interest of 8 percent. (FV of $1, PV of $1, FVA of $1, and PVA of $1)(Use the appropriate factor(s) from the tables provided. Round your final answer to whole dollars.)Required: 1. Prepare the journal entry to record the issuance of the bonds. The marginal average cost of producingxdigital sports watches is given by the functionC(X), whereC(x)is the average cost in dotiars.C(x)=x21.200C(100)=25Find the average cost function and the cost function. What are the fixed costs? The average cost function isC(x)=The cost function isC(x)=The fixed costs are : ___