how is oxygen in a container made to be at a high pressure?​

Answers

Answer 1

Answer:

Oxygen in a container can be made to be at a high pressure through a process called compression. In this process, the oxygen is forced into a smaller volume, which increases the pressure. This can be done using a compressor, which is a machine that uses a piston or other device to compress the oxygen. The compressed oxygen is then stored in a container, such as a cylinder, at high pressure until it is ready to be used. It is important to handle compressed oxygen with care, as it can be dangerous if not handled properly.


Related Questions

19) the best way to reverse a vehicle when turning is to, ? (a) use mirrors and back up cameras (if available). (b) turn around once and then use your mirrors. (c) check all mirrors, complete head checks, and use back up cameras if available. (d) back up as quickly as possible because it is a risky maneuver.

Answers

When turning, check all mirrors, do head checks and use back-up cameras if accessible. So the correct answer is option c.

Safely reversing a car while turning requires awareness of the surroundings. It emphasises monitoring all mirrors, which can reveal nearby vehicles and objects. Head checks over your shoulder are essential to find blind spots that may not be evident in the mirrors. Back-up cameras can further improve visibility and awareness.

Mirrors, head checks, and back-up cameras (if available) let drivers see their surroundings, identify risks, and make informed judgements while reversing and turning. This reduces collisions and improves manoeuvrability.

To know more about mirrors

https://brainly.com/question/1126858

#SPJ4

The dipole would point towards the partial negative charge on the N The dipole would point towards the partial negatlve charge on the C. The dipole would point fowards the partial negative charge on the C The dipole would point towards the partial negative charge an the 0 Part C N−S The dipole would point towards the partial negative charge on the N. The dipole would point towards the partial negative charge ne the S Part D B−Cl The dpole would point towatds the piartial negative charge on the B The dipole would point towards the partial negative charge on the CE

Answers

Part A: The dipole would point towards the partial negative charge on the N. (True)

Part B: The dipole would point towards the partial negative charge on the C. (False)

Part C: The dipole would point towards the partial negative charge on the C. (False)

Part D (B−Cl): The dipole would point towards the partial negative charge on the Cl. (True)

In a polar covalent bond, the electron density is unevenly distributed between the bonded atoms, resulting in partial positive and partial negative charges. The direction of the dipole moment, represented by an arrow, points towards the more electronegative atom (partial negative charge).

In Part A, the dipole would point towards the partial negative charge on the N because nitrogen (N) is more electronegative than hydrogen (H).

In Part B, the dipole would point towards the partial negative charge on the C is false because the difference in electronegativity between C and H is not significant enough to create a polar covalent bond.

In Part C, the dipole would point towards the partial negative charge on the C is false because carbon (C) is not significantly more electronegative than hydrogen (H) to create a polar covalent bond.

In Part D (B−Cl), the dipole would point towards the partial negative charge on the Cl because chlorine (Cl) is more electronegative than boron (B).

To learn more about density, Click here: brainly.com/question/29775886?

#SPJ11

An eccentricity of 0 produces
a circular orbit
straight line motion
a parabolic orbit
an orbit with eccentricity like the Earth's orbit
According to Newton's Law of Gravitation the force between two objects is F =G(M 1M 2)/r 2 where G is the gravitational constant, M 1 and M 2 are the masses of two objects and r is the distance between the two objects. If you were to move the two objects twice as far apart as they originally were, what would happen to the force between them?
it would be 2 times as much
it would be 4 times as much
it would be 1/2 as much
It would be 1/4 as much
Finding patterns that link two quantities is
interesting but doesn't prove there is a causal link between the quantities
a sure sign that one causes another
always pure coincidence
there is no way to know whether there is a causal relationship or not
The average distance of a planet from the sun is the same as
semi-major axis
radius vector
perihelion distance
aphelion distance

Answers

The force between the two objects would be 1/4 as much if you moved them twice as far away. According to Newton's Law of Gravitation, the force between two objects is inversely proportional to the square of their distance. Double the distance reduces force by 1/4.

An orbit with zero eccentricity is circular. The orbit is circular when the eccentricity is 0, therefore the distance between the two objects stays constant. If you moved the two items twice as far apart, Newton's Law of Gravitation says the force between them would be 1/4 as large. The square of the distance between objects is inversely proportional to the force. The force is 1/4 of its initial value when the distance is doubled.

Patterns linking two quantities are intriguing, but they don't indicate a causal relationship. A cause-and-effect relationship cannot be established by correlation or patterns alone. Further inquiry and proof are needed to determine if the quantities are causally related. A planet's semi-major axis is its average distance from the Sun. The average distance between the planet and the Sun during its elliptical orbit is it.

To know more about Newton's Law

https://brainly.com/question/10454047

#SPJ4

Find an equation in standard form for the ellipse with center at (6,9), horizontal major axis of length 6 and passes through the point (7,8).

Answers

To find an equation in standard form for the ellipse with center at (6, 9), horizontal major axis of length 6 and passes through the point (7, 8).

the following steps are to be followed:Step 1: Plot the given coordinates on the coordinate plane to form an approximate graph of the ellipse.Step 2: Since the center of the ellipse is at (6, 9), the center of the ellipse is (h, k) = (6, 9).Step 3: Since the length of the horizontal major axis is 6, the length of the major axis is 2a = 6, then a = 3.Step 4: Since the point (7, 8) lies on the ellipse, it satisfies the equation of the ellipse.x = 7, y = 8Step 5: Let (x, y) be any point on the ellipse. Using the distance formula, find an equation that relates x, y, a, and b, and (h, k).x - h/a2 + y - k/b2 = 1Step 6: Substitute the values of a, b, h, and k found in the previous steps into the equation to obtain the standard form of the equation of the ellipse. Therefore, the equation in standard form for the ellipse with center at (6, 9), horizontal major axis of length 6 and passes through the point (7, 8) is(x - 6)²/9 + (y - 9)²/4 = 1 (long answer)Explanation:The standard form of the equation of an ellipse with horizontal major axis is given by(x - h)²/a² + (y - k)²/b² = 1where (h, k) is the center of the ellipse, a is the distance from the center to a vertex (end) of the major axis, and b is the distance from the center to a vertex of the minor axis.

Since the center of the ellipse is (6, 9) and the length of the horizontal major axis is 6, the center of the ellipse is (h, k) = (6, 9) and the length of the major axis is 2a = 6. Then, a = 3. Therefore,(h, k) = (6, 9) and a = 3.Next, since the point (7, 8) lies on the ellipse, it satisfies the equation of the ellipse, which is given by(x - 6)²/9 + (y - 9)²/b² = 1Since (7, 8) lies on the ellipse,(7 - 6)²/9 + (8 - 9)²/b² = 1=> 1/9 + 1/b² = 1=> 1/b² = 1 - 1/9=> 1/b² = 8/9=> b² = 9/8 * a² => b² = 9/8 * 3² => b² = 81/8 => b = 3√2/2Therefore, a = 3 and b = 3√2/2. Thus, the equation of the ellipse is(x - 6)²/9 + (y - 9)²/(3√2/2)² = 1Multiplying both sides by (3√2/2)², we get

(3√2/2)²(x - 6)²/9 + (y - 9)²

= (3√2/2)²=> 2(x - 6)²/18 + (y - 9)²

= 9/2=> (x - 6)²/9 + 2(y - 9)²/18 = 1

Therefore, the equation of the ellipse in standard form is(x - 6)²/9 + (y - 9)²/4 = 1.

To know more about ellipse visit:-

https://brainly.com/question/20393030

#SPJ11

person a is standing in a parking lot. person b is riding in a car that is moving with velocity (v). person b shines a flashlight in the direction going forward. what speed of light will each person measure?

Answers

Both person A and person B will measure the speed of light to be 'c' (approximately 299,792,458 meters per second).

According to the principles of special relativity, the speed of light in a vacuum is constant and is approximately 299,792,458 meters per second (denoted as 'c'). This speed is the same for all observers, regardless of their relative velocities.

In this scenario, person B is shining a flashlight in the forward direction while riding in a car with velocity 'v'. Let's consider the measurements of the speed of light made by each person:

Person A (standing in the parking lot):

Since person A is at rest relative to the parking lot, they will measure the speed of light to be 'c', which is the standard speed of light in a vacuum.

Measured speed of light for person A: c

Person B (riding in the moving car):

Person B is moving with velocity 'v' relative to person A and the parking lot. According to the principle of special relativity, the measured speed of light for person B will also be 'c'. This is because the laws of physics, including the speed of light, remain constant for all observers, regardless of their relative velocities.

Measured speed of light for person B: c

Therefore, both person A and person B will measure the speed of light to be 'c' (approximately 299,792,458 meters per second).

To know more about speed of light here

https://brainly.com/question/29216893

#SPJ4

a ball is dropped from rest from the top of a building and strikes the ground with a speed vf. from ground level, a second ball is thrown straight upward at the same instant that the first ball is dropped. the initial speed of the second ball is v0 vf, the same speed with which the first ball eventually strikes the ground. ignoring air resistance, decide whether the balls cross paths (a) at half the height of the building, (b) above the halfway point, or (c) below the halfway point.

Answers

The balls will cross paths above the halfway point of the building. When the first ball is dropped from rest, it accelerates due to gravity and gains speed as it falls. At the instant the first ball is dropped, the second ball is thrown straight upward with an initial speed equal to the final speed of the first ball.

Since the second ball is initially thrown upward, it will have an initial velocity in the opposite direction of the first ball's velocity. As the second ball moves upward, it slows down due to the opposing force of gravity. Eventually, it reaches its maximum height and starts to fall back down.
During this time, the first ball continues to accelerate downward and gains speed. As a result, the first ball will cover a greater distance in the same amount of time compared to the second ball.
Therefore, when both balls are in motion, the first ball will reach the ground before the second ball reaches the halfway point of the building. Thus, the balls will cross paths above the halfway point of the building.

To learn more about, Accelerates, click here: https://brainly.com/question/2303856

#SPJ11

A series parallel RLC circuit, the resistance is 1000 ohms, the capacitor is 0.25 micro-farads and inductor is 20 millihenries, is connected to an AC voltage source that can operate between 10 Hz to 100 kHz. a Write the differential equation for the capacitor voltage. b. Use the Fourier transform to obtain the magnitude of frequency response of the capacitor voltage. c. Use the Fourier transform to obtain the phase of the frequency response of the capacitor voltage. d Sketch the magnitude of the frequency response for the frequency range of the source.

Answers

The transfer function represents the relationship between the input frequency and the magnitude of the output signal (capacitor voltage) at each frequency.

a) To write the differential equation for the capacitor voltage, we can use Kirchhoff's voltage law (KVL) for the series parallel RLC circuit. The voltage across the capacitor can be represented by the variable Vc(t).

The KVL equation for the circuit is:

V(t) = VR + VL + VC

Where:

V(t) is the applied voltage,

VR is the voltage across the resistor (R),

VL is the voltage across the inductor (L),

VC is the voltage across the capacitor (C).

Using Ohm's law and the relationships for voltage across inductor and capacitor in an AC circuit, we have:

V(t) = IR + IL + Vc(t)

V(t) = R * d(I(t))/dt + L * d(I(t))/dt + Vc(t)

Since the capacitor current is the derivative of the capacitor voltage, we can substitute I(t) = C * d(Vc(t))/dt into the equation:

V(t) = R * d(C * d(Vc(t))/dt)/dt + L * d(C * d(Vc(t))/dt)/dt + Vc(t)

Simplifying the equation, we get the differential equation for the capacitor voltage:

V(t) = R * C * d²(Vc(t))/dt² + (R * d(Vc(t))/dt + L * d²(Vc(t))/dt²) + Vc(t)

b) To obtain the magnitude of the frequency response of the capacitor voltage, we can apply the Fourier transform to the differential equation obtained in part (a). By solving the transformed equation, we can find the magnitude of the frequency response as a function of frequency.

c) Similarly, to obtain the phase of the frequency response of the capacitor voltage, we can apply the Fourier transform to the differential equation obtained in part (a). By solving the transformed equation, we can find the phase of the frequency response as a function of frequency.

d) Sketching the magnitude of the frequency response for the frequency range of the source requires analyzing the transfer function obtained from the frequency response in parts (b) and (c).

The transfer function represents the relationship between the input frequency and the magnitude of the output signal (capacitor voltage) at each frequency.

By plotting the magnitude of the transfer function for the frequency range of the source, we can sketch the magnitude of the frequency response.

To know more about magnitude refer here:

https://brainly.com/question/31022175#

#SPJ11

a) What is the difference between a feed in tariff and a net-metering mechanism for connection of distributed generators to the electric grid? [6 marks] (b) It is being proposed to construct a tidal barrage. The earmarked surface area in the sea is 1 km2. What should be the head of the barrage if 2MW of power should be generated between a high tide and a low tide? Density of seawater =1025 kg/m3 and g=9.8 m/s2 [7 marks] (c) Describe the main difference between a Pelton and a Kaplan turbine and suggest in which conditions they are recommended for use

Answers

The amount of electricity they generate. When the generator produces more electricity than it consumes, the excess is fed back into the grid, and the generator receives credits for the surplus electricity.

a) Feed-in Tariff (FiT) and Net Metering are two different mechanisms for connecting distributed generators to the electric grid:

Feed-in Tariff (FiT): Under a FiT mechanism, a fixed price per unit of electricity generated by a distributed generator is set by the government or utility company.

This price is typically higher than the retail electricity price to incentivize renewable energy generation. The distributed generator sells the entire generated electricity to the grid, and the utility company pays the generator based on the FiT rate.

The generator does not consume the generated electricity on-site but exports it to the grid. FiTs provide long-term contracts and stable income for distributed generators, encouraging the development of renewable energy projects.

Net Metering: Net metering allows distributed generators to offset their electricity consumption by the amount of electricity they generate. When the generator produces more electricity than it consumes, the excess is fed back into the grid, and the generator receives credits for the surplus electricity.

These credits can be used to offset the generator's electricity consumption during periods when the generator's production is less than its consumption (e.g., during nighttime).

The net metering mechanism requires a bidirectional meter that can measure both the electricity imported from the grid and the exported electricity.

In summary, the key differences between FiT and net metering are:

FiT pays the generator a fixed price per unit of electricity generated, while net metering provides credits for the excess electricity fed back into the grid.

Under FiT, the generator sells all the generated electricity to the grid, while net metering allows the generator to offset its consumption with the generated electricity.

FiT provides stable income through long-term contracts, while net metering allows for self-consumption and reduces electricity bills by offsetting consumption.

b) To calculate the head required for generating 2 MW of power with a tidal barrage, we can use the following formula:

Power = (Density of seawater) x (Gravity constant) x (Area of the barrage) x (Head) x (Efficiency)

Given:

Power = 2 MW = 2,000,000 Watts

Density of seawater = 1025 kg/m³

Gravity constant (g) = 9.8 m/s²

Area of the barrage = 1 km² = 1,000,000 m²

Efficiency (not provided)

Rearranging the formula, we can solve for the head:

Head = Power / (Density of seawater x Gravity constant x Area of the barrage x Efficiency)

Please note that the efficiency value is crucial in determining the head required, but it is not provided in the question. The efficiency represents the conversion efficiency of the tidal barrage system and can vary depending on the specific technology used.

c) The main difference between a Pelton and a Kaplan turbine lies in their design and the specific conditions under which they are recommended for use:

Pelton Turbine: A Pelton turbine is a type of impulse turbine designed for high head applications. It consists of one or more water jets directed onto spoon-shaped buckets mounted on the perimeter of a wheel.

The water jets strike the buckets tangentially, creating a high-velocity jet that imparts impulse force to the buckets. This impulse force causes the wheel to rotate, converting the kinetic energy of the water into mechanical energy.

Pelton turbines are suitable for locations with high heads and low flow rates, such as mountainous regions with steep rivers or hilly terrains.

Kaplan Turbine: A Kaplan turbine is a type of reaction turbine designed for low head applications. It features adjustable blades or vanes that allow for efficient operation across a range of flow rates and heads.

To know more about surplus refer here:

https://brainly.com/question/28537213#

#SPJ11

Question: In an average year, the Creek drainage basin (150 mi^2) receives 550 mm of precipitation. Has an average stream discharge of 1.8 m^3s^-1. (1 mile = 1.609 km).
Please develop the water budget equation for this problem.

Answers

The water budget equation for the Creek drainage basin is: Precipitation = Stream discharge + Evapotranspiration ± Change in storage.

To develop the water budget equation for this problem, we need to account for the inputs and outputs of water in the Creek drainage basin. The water budget equation can be expressed as,

P = Q + ET ± ΔS

P = Precipitation input (mm)

Q = Stream discharge (m³/s)

ET = Evapotranspiration (mm)

ΔS = Change in storage (mm)

First, let's convert the units of the given values,

Precipitation input (P) = 550 mm

Stream discharge (Q) = 1.8 m³/s

Now, let's determine the evapotranspiration (ET) and change in storage (ΔS) terms. However, the problem doesn't provide information about ET, so we cannot calculate it accurately. The problem doesn't provide information about ΔS, so we cannot calculate it accurately.

Given these limitations, we can write the simplified water budget equation for this problem,

550 mm = 1.8 m³/s + ET ± ΔS

Please note that without information about evapotranspiration and changes in storage, we cannot fully determine the water budget for the Creek drainage basin.

To know more about budget equations, visit,

https://brainly.com/question/32563921

#SPJ4

when a 2.90-kg object is hung vertically on a certain light spring described by hooke's law, the spring stretches 2.62 cm. (a) what is the force constant of the spring?

Answers

The force constant of the spring can be found by dividing the weight of the object by the displacement of the spring: 1086.26 N/m.

To find the force constant of the spring, we can use Hooke's Law, which states that the force exerted by a spring is directly proportional to the displacement from its equilibrium position.

Hooke's Law can be written as F = -kx, where F is the force exerted by the spring, k is the force constant (also known as the spring constant), and x is the displacement from the equilibrium position.

In this case, the displacement of the spring is 2.62 cm, which is equal to 0.0262 m. The object has a mass of 2.90 kg, so its weight is given by W = mg, where g is the acceleration due to gravity (approximately 9.8 m/s^2). The weight of the object is equal to the force exerted by the spring when it is in equilibrium.

Therefore, we have W = F = kx. Substituting the given values, we get:

m * g = k * x

2.90 kg * 9.8 m/s^2 = k * 0.0262 m

Solving for k, we find:

k = (2.90 kg * 9.8 m/s^2) / 0.0262 m ≈ 1086.26 N/m

So, the force constant of the spring is approximately 1086.26 N/m.

Know more about Hooke's Law here:

https://brainly.com/question/29296378

#SPJ8

A single acting air compressor with a clearance of 6% takes in air at atmospheric pressure and temperature of 85 ∘
F and discharges it at a pressure of 85 psia. The air handled is 0.25ft 3
/ cycle measured at discharge pressure. If the compression is isentropic, find the piston displacement per cycle, if the compressor is running at 750 rpm. A. 0.0750ft/cycle B. 0.025ft/ cycle C. 1.030ft/cycle D. 1.090ft/ cycle

Answers

The piston displacement per cycle for the given air compressor running at 750 rpm is approximately 0.00005 ft/cycle.

To find the piston displacement per cycle for the given single-acting air compressor, we can use the ideal gas law and the isentropic compression process.

The ideal gas law states:

P * V = n * R * T

Where:

P = pressure

V = volume

n = number of moles of gas

R = gas constant

T = temperature

For an isentropic compression process, we have:

P1 * V1^γ = P2 * V2^γ

P1 = initial pressure (atmospheric pressure)

V1 = initial volume (volume at atmospheric pressure)

P2 = final pressure (discharge pressure)

V2 = final volume (volume at discharge pressure)

γ = ratio of specific heat capacities for air (typically around 1.4)

First, let's convert the given temperature from Fahrenheit to Rankine (absolute temperature scale):

T1 = 85°F + 460°F (conversion to Rankine)

= 545°R

Since the compressor has a clearance of 6%, the initial volume (V1) can be calculated as:

V1 = (1 + clearance) * V_cycle

= (1 + 0.06) * 0.25 ft^3

= 1.06 * 0.25 ft^3

= 0.265 ft^3

Next, we can calculate the final volume (V2) using the isentropic compression equation:

P1 * V1^γ = P2 * V2^γ

V2^γ = (P1 * V1^γ) / P2

V2 = ((P1 * V1^γ) / P2)^(1/γ)

Substituting the values:

V2 = ((14.7 psia * (0.265 ft^3)^1.4) / 85 psia)^(1/1.4)

≈ 0.334 ft^3 (approximately)

The piston displacement per cycle (D) can be calculated by subtracting the initial volume from the final volume:

D = V2 - V1

= 0.334 ft^3 - 0.265 ft^3

≈ 0.069 ft^3

Since the compressor is running at 750 rpm, the piston displacement per cycle can be converted to displacement per cycle:

Displacement per cycle = D / (number of cycles per minute)

= 0.069 ft^3 / (750 cycles/minute)

≈ 0.000092 ft^3/cycle

To express the answer in feet per cycle, we can convert cubic feet to feet:

Displacement per cycle ≈ 0.000092 ft^3/cycle

≈ 0.092 in^3/cycle

≈ 0.00005 ft/cycle

≈ 0.00005 ft

To know more about displacement refer here

https://brainly.com/question/11934397#

#SPJ11

based on your experimental results, how does the number of segments in a standing wave vary with the tension in the string when the frequency is constant? how well do your measurements match the theoretical relationship between number of segments and string tension? write out your answer in a clear and well supported paragraph

Answers

The number of segments in a standing wave varies inversely with the tension in the string when the frequency is held constant. The measured values generally support this relationship, although there may be some discrepancies between the measured and theoretical values due to experimental limitations.

Based on the provided data, it is possible to analyze the relationship between the number of segments in a standing wave and the tension in the string, while keeping the frequency constant. The data shows the measured values of the number of segments (n) for different tension values (FT) in Table 1 and Table 2.

Upon examining the data in Table 1, it can be observed that as the tension in the string increases, the number of segments decreases. This relationship suggests an inverse correlation between tension and the number of segments when the frequency is held constant. The measured values align with this trend, as indicated by the decreasing values of n with increasing tension.

Similarly, the data in Table 2 supports the inverse relationship between tension and the number of segments. As the tension increases, the number of segments decreases. The measured values of n align with this relationship, demonstrating a consistent trend.

Comparing the measured values to the theoretical relationship, it is evident that the data does not perfectly match the expected relationship. The calculated slope from the data in Table 1 is slightly different from the expected slope of -0.034, and the calculated slope from the data in Table 2 deviates from the expected slope of 15.6. These differences, indicated by the percentage differences, suggest some level of experimental error or variability in the measurements.

In conclusion, based on the experimental results, it can be inferred that the number of segments in a standing wave varies inversely with the tension in the string when the frequency is held constant. The measured values generally support this relationship, although there may be some discrepancies between the measured and theoretical values due to experimental limitations.

To know more about frequency:

https://brainly.com/question/33523853

#SPJ4

--The question is incomplete, the given complete question is:

"Based on your experimental results, how does the number of segments in a standing wave vary with the tension in the string when the frequency is constant? How well do your measurements match

The theoretical relationship between the number of segments and string tension?

Write out your answer in a clear and well-supported paragraph.

Table 1    

m (sim) =

3.2×10⁻³ kg/m

L = 4 m  

f = 125 Hz  

n 1/n2 FT  

6 0.028 88.89  

7 0.020 65.30  

8 0.016 50.02  

9 0.012 39.52  

10 0.010 31.91  

11 0.008 26.45  

12 0.007 22.20  

slope =

3201.6x-0.034

m (calc) =

3201.6 or 3.201×10⁻³

% diff = 0.0312  

Table 2    

m (sim) =

3.2×10⁻³ kg/m

L = 4 m  

FT = 50 N  

n f  

6 93.77  

7 109.38  

8 125.00  

9 140.63  

10 156.25  

11 171.88  

12 187.50  

slope = 15.6×x+0.0243 slope is 15.6

m (calc) = 3.21026×10⁻³ kg/m

% diff = 0.32"--

What individuals were responsible for the birth of
motion pictures? Teacher is looking for 5 components

Answers

The birth of motion pictures involved the contributions of several key individuals and components. Here are five important components and the individuals associated with them:

1. Persistence of Vision: The concept of persistence of vision, which allows the brain to perceive a rapid sequence of images as continuous motion, was crucial in the development of motion pictures.

2. Photography: The invention of photography laid the foundation for motion pictures. Key figures in the development of photography include Joseph Nicéphore Niépce, Louis Daguerre, and William Henry Fox Talbot.

3. Zoetrope: The zoetrope was an early device that produced the illusion of motion by spinning a drum containing a sequence of images.

4. Chrono photography: Étienne-Jules Marey and Eadweard Muybridge made significant contributions to chrono photography, which involved capturing multiple frames of motion in quick succession.

5. Cinematograph: The Lumière brothers, Auguste and Louis Lumière, are credited with inventing the cinematograph, a combination of camera, film processing, and projection system.

To know more about photography:

https://brainly.com/question/31166522

#SPJ4

an artificial satellite circles the earth in a circular orbit at a location where the acceleration due to gravity is 8.34 m/s2. determine the orbital period of the satellite.'

Answers

To determine the orbital period of the satellite, we can use Kepler's third law, which relates the orbital period (T) of a satellite to the radius (r) of its circular orbit. The orbital period is √((4π² / 8.34 m/s²) * r).

Kepler's third law can be stated as:

T² = (4π² / GM) * r³

where G is the gravitational constant and M is the mass of the Earth.

In this case, we are given the acceleration due to gravity (g) at the location of the satellite, which is related to the gravitational constant and the mass of the Earth by the equation:

g = GM / r²

Rearranging the equation, we can solve for GM:

GM = g * r²

Substituting this expression for GM into Kepler's third law equation:

T² = (4π² / (g * r²)) * r³

Simplifying:

T² = (4π² / g) * r

Taking the square root of both sides:

T = √((4π² / g) * r)

Now we can substitute the given value of g and solve for T:

T = √((4π² / 8.34 m/s²) * r)

To know more about Kepler's third law

https://brainly.com/question/30404084

#SPJ4

All the stator flux in a star-connected, three-phase, two-pole, slip-ring induction motor may be assumed to link with the rotor windings. When connected direct-on to a supply of 415 V, 50 Hz the maximum rotor current is 100 A. The standstill values of rotor reactance and resistance are 1.2 Ohms /phase and 0.5 Ohms /phase respectively. a. Calculate the number of stator turns per phase if the rotor has 118 turns per phase. [3] b. At what motor speed will maximum torque occur? [2] c. Determine the synchronous speed, the slip speed and the rotor speed of the motor

Answers

a. Number of stator turns per phase: 49.17 turns per phase.

b. Maximum torque occurs at half the synchronous speed.

c. Synchronous speed: 3000 RPM, Slip speed: 3000 RPM, Rotor speed: 0 RPM.

a. The number of stator turns per phase can be calculated using the formula:

Number of stator turns per phase = Number of rotor turns per phase × (Rotor reactance / Stator reactance)

Number of stator turns per phase = 118 × (0.5 / 1.2) = 49.17 turns per phase (approximately)

b. The motor speed at which maximum torque occurs can be determined by dividing the synchronous speed by the slip factor.

Maximum torque speed = Synchronous speed / (1 + Slip)

Since the slip factor at maximum torque is 1, the maximum torque speed is half the synchronous speed.

Maximum torque speed = Synchronous speed / 2

c. The synchronous speed (Ns) of the motor can be calculated using the formula:

Synchronous speed (Ns) = (120 × Frequency) / Number of poles

In this case, with a frequency of 50 Hz and a two-pole motor, the synchronous speed is:

Synchronous speed (Ns) = (120 × 50) / 2 = 3000 RPM

The slip speed is the difference between the synchronous speed and the rotor speed. At standstill, the rotor speed is zero.

Slip speed = Synchronous speed - Rotor speed = 3000 RPM - 0 RPM = 3000 RPM

The rotor speed (Nr) is zero at standstill.

To know more about Synchronous speed refer here

https://brainly.com/question/31605298#

#SPJ11

What is the Thevenin voltage, En, of the STEP GENERATOR if an open-circuit voltage Voc of 1.0 V is measured at the 5-0 BNC output of this generator? 5.0 V a. b. 0.2 V c. 0.5 V 1.0 V d.

Answers

The Thevenin voltage (En) represents the voltage source that can replace a complex circuit when viewed from its output terminals.

To determine the Thevenin voltage of the step generator, we consider the open-circuit voltage (Voc) measured at the 5-0 BNC output, which is 1.0 V in this case.

The open-circuit voltage is the voltage across the output terminals when no load is connected. It indicates the voltage generated by the internal source of the step generator without any external load affecting it. Therefore, the open-circuit voltage is equal to the Thevenin voltage.

Hence, in this scenario, the Thevenin voltage (En) of the step generator is 1.0 V.

This means that the step generator can be represented by a voltage source of 1.0 V connected in series with an internal resistance, which captures the behavior of the generator when connected to various loads.

The options provided are:

a. 5.0 V

b. 0.2 V

c. 0.5 V

d. 1.0 V

Among these options, the correct answer is d) 1.0 V, which matches the measured open-circuit voltage (Voc) of the step generator.

To know more about Thevenin refer here:

https://brainly.com/question/30013215#

#SPJ11

The steamer ‘Ostrich’ ferries people between Dhaka and Barisal. Ostrich usually starts from
Dhaka around 7.30pm (evening/night depending on the season). At night, the visibility is
usually very low. So, the steamers/launches usually have a flashing signal light on the roof.
On top of that, the master of the steamer also honks the horn when necessary. This signal
light and the horn are both controlled by an Arduino Uno. The signal light flashes every 4s
whereas the horn is sounded whenever the master presses the horn switch. The horn switch
already has a small RC circuit attached to it to counter bouncing. Now, prepare a program in
Arduino Uno to control the signal light and the horn considering the information mentioned
above.

Answers

The loop() function is where the control logic happens. We use the millis() function to keep track of time and toggle the signal light state every 4 seconds. We also check the status of the horn switch using digitalRead().

Here is an example program in Arduino Uno to control the signal light and horn based on the provided information:

// Pin assignments

const int signalLightPin = 2;  // Signal light connected to digital pin 2

const int hornPin = 3;         // Horn connected to digital pin 3

const int hornSwitchPin = 4;   // Horn switch connected to digital pin 4

// Timing variables

const unsigned long signalLightInterval = 4000;  // Signal light interval in milliseconds

// State variables

boolean signalLightState = LOW;  // Initial state of the signal light

boolean hornState = LOW;         // Initial state of the horn

unsigned long previousSignalTime = 0;  // Variable to store the previous signal light time

void setup() {

 pinMode(signalLightPin, OUTPUT);

 pinMode(hornPin, OUTPUT);

 pinMode(hornSwitchPin, INPUT_PULLUP);  // Use internal pull-up resistor for the horn switch

}

void loop() {

 // Control the signal light

 unsigned long currentMillis = millis();

 if (currentMillis - previousSignalTime >= signalLightInterval) {

   previousSignalTime = currentMillis;

   signalLightState = !signalLightState;  // Toggle the signal light state

   digitalWrite(signalLightPin, signalLightState);

 }

 // Control the horn

 if (digitalRead(hornSwitchPin) == LOW) {

   hornState = HIGH;  // Activate the horn if the horn switch is pressed

 } else {

   hornState = LOW;   // Deactivate the horn otherwise

 }

 digitalWrite(hornPin, hornState);

}

In this program, we declare the necessary pin assignments for the signal light, horn, and horn switch. We also define the timing interval for the signal light to flash every 4 seconds.

Inside the setup() function, we set the pinMode for the signal light and horn pins as OUTPUT, and the horn switch pin as INPUT_PULLUP to enable the internal pull-up resistor.

If the switch is pressed (LOW state), we set the horn state to HIGH to activate the horn, and if it's not pressed (HIGH state), we set the horn state to LOW to deactivate the horn. Finally, we use digitalWrite() to control the state of the signal light and horn pins accordingly.

With this program, the signal light will flash every 4 seconds, and the horn will be activated whenever the horn switch is pressed.

To know more about toggle refer here:

https://brainly.com/question/30638140#

#SPJ11

Draw a scale vector diagram showing the resultant force of 3N and 5N pushing a mass west

Answers

A scale vector diagram showing the resultant force of 3N and 5N pushing a mass west given below:

3N     5N

   |      |

   |      |

   |      |

----+------O----> West

In this diagram, the 'O' represents the mass, and the arrows labeled '3N' and '5N' represent the forces of 3N and 5N, respectively. The arrows point to the left (west) to indicate the direction of the forces.To scale the diagram, you can assign a specific length to each unit of force, such as 1 centimeter (cm) per newton (N). So, if you decide that 1 cm represents 1N, you can draw an arrow 3 cm long to represent the 3N force and another arrow 5 cm long to represent the 5N force.

For such more question on vector diagram

https://brainly.com/question/18604649

#SPJ8

The difference between the energy of the light wave of a H electron moving from energy level 3 to energy level 2 and the one moving from energy level 4 to energy level 2 corresponds to the energy of a H electron moving from energy level 4 to A (a digit).

Answers

The difference between the energy of the light wave of a hydrogen (H) electron moving from energy level 3 to energy level 2 and the one moving from energy level 4 to energy level 2 corresponds to the energy of a hydrogen electron moving from energy level 4 to another energy level labeled as A.

To determine the energy difference between energy level 4 and energy level A, we need more information about the specific energy levels of hydrogen and the corresponding energy values. The energy levels in hydrogen are quantized, and each energy level is associated with a specific energy value. Without knowing the energy value of energy level A, we cannot calculate the exact energy difference.

However, in general, the energy difference between any two energy levels in a hydrogen atom can be calculated using the Rydberg formula or the Bohr model. These formulas provide a mathematical relationship between the energy levels and the corresponding energy values. Once we know the energy levels and their associated values, we can determine the energy difference between energy level 4 and energy level A.

To learn more about light wave, Click here: brainly.com/question/16398728?

#SPJ11

The power in a circuit is 1,500 watts and the resistance is 20 ohms. What is the
current rounded to three decimal places?
A. 75 A
B. 300 A
C. 8.660 A
D. 19.365 A

Answers

The current to three decimal places is 75 A. The correct option is A

How to calculate the current in a circuit

We can use Ohm's law, which states that the current (I) is equal to the power (P) divided by the resistance (R):

I = P / R

Substituting the given values into the equation:

I = 1500 W / 20 Ω

I = 75 A

Therefore, the current to three decimal places, the answer 75 A

Learn more about Ohm's law here : brainly.com/question/796939

#SPJ1

Part 1: Mass determination using the triple-beam balance Weighing the mass by difference: 1. Place the weighing boat on the balance pan and record the mass. 2. Add the object to the weighing boat and record the mass. 3. The difference between these two masses corresponds to the net mass of the object. Mass of the empty weighing boat (wb): (do not add this mass to the mass of the object, it is included when you read the measurement of the object in the video) Part 2: Mass determination using the analytical balance Weighing the mass directly: 1. Place the weighing boat on the pan of the balance. 2. Press the zero/tare button. This will electronically subtract the mass of the weighing boat and re-set the display to zero. 3. Add the object and record the mass. Mass of the empty wb: 2.090 g Question 1: Which of the two types of balances (triple-beam or analytical) is more accurate? Explain. Question 2: What is the uncertainty of the mass measurements on each balance? Question 3: Choose one object and write how its mass determined on a triple-beam and analytical scale should be reported. It must show the uncertainty, i.e: 1.05±0.01 g.

Answers

The mass determination using the triple-beam balance involves weighing the object by difference, which includes recording the mass of the weighing boat and then subtracting it from the combined mass of the object and weighing boat.

To determine the mass of an object using the triple-beam balance, the process of weighing by difference is followed. First, the empty weighing boat is placed on the balance pan, and its mass is recorded separately. Then, the object to be weighed is added to the weighing boat, and the combined mass of the object and the weighing boat is recorded.

The difference between the two recorded masses corresponds to the net mass of the object alone since the mass of the empty weighing boat is already accounted for in the first measurement. By subtracting the mass of the weighing boat from the combined mass, we obtain the mass of the object.

This method helps eliminate the need to directly measure the mass of the object alone and instead focuses on the difference in masses before and after adding the object to the weighing boat. It provides an effective way to determine the mass of an object using a triple-beam balance.

To learn more about triple-beam, Click here: brainly.com/question/32875846?

#SPJ11

3) A square loop of wire lies in the plane of the page. An increasing magnetic field is directed into the page. What is the direction of the induced current in the loop. EXPLAIN BRIEFLY WITH THE AID OF A DIAGRAM.

Answers

When an increasing magnetic field is directed into the page and a square loop of wire lies in the plane of the page, the direction of the induced current in the loop can be determined using Faraday's law of electromagnetic induction.

According to Faraday's law, an induced current is generated in a conductor when there is a change in magnetic flux through the loop. The induced current flows in such a way as to create a magnetic field that opposes the change in the magnetic flux.

In this case, as the magnetic field is increasing and directed into the page, the induced current will flow in a direction that creates a magnetic field out of the page. This can be illustrated with the aid of a diagram.

    ^

    |

-----|-----    --> Direction of increasing magnetic field into the page

    |

    v

The induced current in the loop will flow in a counterclockwise direction, as viewed from above the plane of the page. This creates a magnetic field that points out of the page, opposing the increasing magnetic field.

The direction of the induced current can also be determined using the right-hand rule. If the fingers of the right hand are curled in the direction of the increasing magnetic field, the thumb points in the direction of the induced current.

In summary, when an increasing magnetic field is directed into the page and a square loop of wire lies in the plane of the page, the induced current in the loop flows counterclockwise, creating a magnetic field out of the page to oppose the change in the magnetic flux.

To know more about electromagnetic refer here:

https://brainly.com/question/23727978#

#SPJ11

Consider a Full wave rectifier fed by a 120-Hz sinusoid having a peak value Vp=50 V. Let the load resistance R = 10 k 2. Find the value of the capacitance that will result in a peak- to-peak ripple of 1 V. In addition, Calculate the fraction of the cycle during which the diode is conducting. Also, the average and peak values of the diode current. a. Capacitance UC b. Conduction Angle rad mA c. Average Diode Current d. Peak Diode Current mA

Answers

a. Capacitance UC = 2.65 µF

b. Conduction Angle θ = 1.047 radians

c. Average Diode Current[tex]Id_{avg}[/tex] = 2.15 mA

d. Peak Diode Current [tex]Id_{peak}[/tex] = 2.16 mA.

To find the value of the capacitance (UC) that will result in a peak-to-peak ripple of 1 V, we can use the formula:

UC = (I / (2 * f * Vr))

where I is the load current, f is the frequency, and Vr is the ripple voltage.

Given that the load resistance R = 10 kΩ (10,000 Ω), and the peak-to-peak ripple Vr = 1 V, we can substitute these values into the formula:

UC = (I / (2 * 120 Hz * 1 V))

To calculate the conduction angle (θ), we can use the formula:

θ = arccos((Vr - Vf) / Vp) * (180 / π)

where Vf is the forward voltage drop across the diode.

To calculate the average diode current ([tex]Id_{avg[/tex]), we can use the formula:

[tex]Id_{avg}[/tex]= (Vp - Vf) / (2 * R)

where Vp is the peak voltage.

To calculate the peak diode current ([tex]Id_{peak[/tex]), we can use the formula:

[tex]Id_{peak[/tex] = [tex]Id_{avg[/tex] + (Vr / (2 * R))

Given that the load resistance R = 10 kΩ (10,000 Ω), the peak voltage Vp = 50 V, and assuming a forward voltage drop Vf of approximately 0.7 V for a typical diode

To know more about Capacitance refer here

https://brainly.com/question/31871398#

#SPJ11

If you started with 8 grams of "parent" atoms, you would have 4
grams of "daughter" atoms after one ________.

Answers

If you started with 8 grams of "parent" atoms, you would have 4 grams of "daughter" atoms after one half-life.

In radioactive decay processes, the parent atoms decay over time into daughter atoms. The time it takes for half of the parent atoms to decay is called the half-life.

If you start with 8 grams of parent atoms and undergo one half-life, This results in a decrease in the number of parent atoms and an increase in the number of daughter atoms.

Then left with 4 grams of parent atoms and 4 grams of daughter atoms after one half-life.

To know more about the half-life period:

https://brainly.com/question/1042167

#SPJ4

Describe the impact hypothesis for the K-T mass extinction. Describe the original evidence that was used to propose this hypothesis. What other evidence supports the hypothesis? What effects might have occurred as a result of such an impact?

Answers

The Cretaceous-Tertiary mass extinction is thought to have been caused by a huge asteroid or comet impact, according to the impact hypothesis.

The impact hypothesis for the K-T (Cretaceous-Tertiary) mass extinction suggests that a large asteroid or comet impact was responsible for the extinction event that occurred approximately 66 million years ago, marking the end of the Cretaceous Period and the beginning of the Tertiary Period. This hypothesis was first proposed by scientists Luis Alvarez, Walter Alvarez, Frank Asaro, and Helen Michel in 1980.

Analysis of a geological layer known as the K-T boundary provided the initial support for the impact hypothesis. Iridium was discovered to be present in this barrier in abnormally high concentrations compared to the Earth's crust's usual levels. Iridium is uncommon in the surface rocks of Earth, although it is plentiful in some extraterrestrial objects, such as comets and asteroids.

These pieces of information clearly suggested an alien impact event close to the K-T barrier. The Chicxulub crater, which has been dated to the same period as the K-T boundary, was discovered by later research to be buried beneath the Yucatán Peninsula in Mexico.

Such a collision would cause immediate destruction close to the collision location, including enormous earthquakes, tsunamis, and flames. A global impact winter brought on by the release of dust and gases into the atmosphere would have resulted in less sunlight reaching the surface of the Earth, a drop in temperature, and a disturbance of the food chain. Numerous species would have perished as a result of these environmental shifts, including the well-known dinosaurs.

Therefore, The Cretaceous-Tertiary mass extinction is thought to have been caused by a huge asteroid or comet impact, according to the impact hypothesis.

To know more about the impact hypothesis, click here:

https://brainly.com/question/32374314

#SPJ4

QUESTION 3
What are characteristics of the 'New Generation of Nuclear
Reactors'?

Answers

Characteristics of the 'New Generation of Nuclear Reactors' includes:

Enhanced Safety FeaturesImproved Efficiency and PerformanceReduced Waste GenerationSustainable Fuel SourcesLoad-Following CapabilitySmaller Footprint and Modular DesignsEnhanced Proliferation Resistance

The "New Generation of Nuclear Reactors" refers to a class of advanced nuclear reactors that are being developed with the aim of improving upon the previous generations of nuclear reactors in terms of safety, efficiency, sustainability, and waste management.

New generation reactors incorporate advanced safety systems and passive cooling mechanisms to ensure safe operation, even in the event of unforeseen incidents or accidents.

Advanced reactors aim to achieve higher thermal efficiencies, meaning they can generate more electricity from the same amount of fuel.

Advanced reactors explore alternative fuel sources beyond traditional uranium-based fuels.

Advanced reactors incorporate features that enhance proliferation resistance, such as inherent physical barriers, advanced fuel cycles, and reduced production of weapons-usable byproducts.

Therefore, the Characteristics of the 'New Generation of Nuclear Reactors' includes:

Enhanced Safety FeaturesImproved Efficiency and PerformanceReduced Waste GenerationSustainable Fuel SourcesLoad-Following CapabilitySmaller Footprint and Modular DesignsEnhanced Proliferation Resistance

To learn more about nuclear reactors, click here:

https://brainly.com/question/12899500

#SPJ4

russ makes the diagram below to organize his notes about how newton’s first law describes objects at equilibrium

Answers

Russ uses the diagram below to organize his notes about how Newton’s First Law describes objects at equilibrium:As per the Newton’s first law, an object will remain in a state of rest or uniform motion in a straight line unless an external force is applied to it. This is known as the Law of Inertia.

According to the diagram, when an object is at equilibrium, the net force acting on it is zero. In other words, the object is not accelerating, it is either at rest or moving with a constant velocity in a straight line direction. If a force is applied to the object, it will cause the object to move. However, if there are no forces acting on the object, then it will remain at rest or in motion as per the Newton’s First Law.Furthermore, objects at equilibrium are balanced in terms of forces acting on them. In other words, the forces acting on the object cancel each other out. The forces can be categorized as either internal or external. Internal forces act within the object, whereas external forces act on the object from the outside. Objects that are at equilibrium have internal and external forces that are equal in magnitude and opposite in direction. As a result, the object does not move, and it is said to be at equilibrium.In conclusion, the Newton’s First Law describes objects at equilibrium by stating that an object will remain in a state of rest or uniform motion in a straight line unless an external force is applied to it. Objects at equilibrium have internal and external forces that are equal in magnitude and opposite in direction, which result in the object not moving.

For such more question on Law of Inertia

https://brainly.com/question/1830739

#SPJ8

An ideal gas undergoes isothermal compression, which reduces its volume by 1800 m3. The final pressure and volume of the gas are 1477.5 torr bar and 2140 cm3, respectively. Calculate the original pressure of the gas in (a) torr, (b) Pa.

Answers

The original pressure of the gas is approximately 1.758 torr.

To calculate the original pressure, we use Boyle's Law equation, which states that the product of initial pressure and volume is equal to the product of final pressure and volume for an isothermal process. By rearranging the equation and substituting the given values, we can solve for the original pressure. The result is approximately 1.758 torr.

To learn more about pressure, Click here: brainly.com/question/29341536?

#SPJ11

A parcel of air at the surface has an air temperature of 17°C. Print out the blank stuve diagram below, and draw both dry and moist adiabats between the surface and 500mb (like I did above). 1 point What would the temperature of the parcel be at 500mb if cooled dry adiabatically? O -25°C -35°C -45°C 1 point What would the temperature of the parcel be at 500mb if cooled moist adiabatically? -15°C -25°C 0 -35°C

Answers

If an air parcel cools adiabatically at the surface with a temperature of 17 °C, the temperature drops by about 10 °C for every 1000 meters of altitude. 500mb is typically about 5500 meters from the surface, so with dry adiabatic cooling the package temperature will be about 17°C - (10°C * 5.5) = -33°C.

On the other hand, if the air parcel is moist and adiabatically cooled, the temperature change will be slower because latent heat is released when the water vapor condenses. The adiabatic temperature drop rate when wet is typically about 6°C per 1000 meters.

However, it is generally cooler than the dry adiabatic decay rate, so for wet adiabatic cooling, the -15°C, -25°C, 0, and -35°C options are possible temperatures for a 500MB package. There is a possibility. . 

To learn more about adiabatic:

https://brainly.com/question/14926413

#SPJ4

Give a short justification with key reasons about your answer. Statement: Since the common-emitter BJT amplifier typically has a relatively low input resistance, it is not a good option for the input stage of a practical amplifier circuit.

Answers

The voltage divider effect, loading effect, difficulties in achieving impedance matching, and increased susceptibility to noise, the common-emitter BJT amplifier with its low input resistance may not be the ideal choice for the input stage of a practical amplifier circuit.

The statement that the common-emitter BJT amplifier is not a good option for the input stage of a practical amplifier circuit due to its low input resistance can be justified with the following key reasons:

Voltage divider effect: The input resistance of a common-emitter amplifier is determined by the base-emitter junction of the BJT, which typically has a low resistance value.

This low input resistance acts as a voltage divider with the signal source impedance, causing a significant voltage drop across the source impedance. This can result in signal attenuation and loss of voltage gain.

Loading effect: The low input resistance of the common-emitter amplifier can cause a significant loading effect on the preceding stages or signal sources.

When the input impedance of a circuit is low, it draws more current from the driving source, which can lead to a decrease in the signal level and distortion of the input signal.

Signal source matching: In practical amplifier circuits, it is often desirable to match the impedance of the amplifier's input stage with the impedance of the signal source for maximum power transfer and minimum signal degradation.

The low input resistance of the common-emitter amplifier makes it difficult to achieve impedance matching, leading to signal reflections and reduced overall performance.

Noise considerations: The low input resistance of the common-emitter amplifier can also contribute to increased noise levels.

The input stage of an amplifier is typically a critical point for noise performance, and a low input resistance can increase the susceptibility to external noise sources and degrade the overall signal-to-noise ratio.

In summary, due to the voltage divider effect, loading effect, difficulties in achieving impedance matching, and increased susceptibility to noise,

the common-emitter BJT amplifier with its low input resistance may not be the ideal choice for the input stage of a practical amplifier circuit.

Other amplifier configurations with higher input resistance, such as the common-source configuration in MOSFET amplifiers, are often preferred in such applications.

To know more about emitter refer here:

https://brainly.com/question/32101419#

#SPJ11

Other Questions
The water level in Phoenix lake varies during the year. Let h(t) be the depth in feet of the water at time t days. So, January 1 would correspond to 0 t < 1. Match each description on the left with the mathematical expression on the right. Not every mathematical expression will be used. The water level is rising and the rise is going faster and faster at time a. The water level is falling at time t = a. The water level is constant at 50 feet on January 2nd. On January 2nd, the water rose steadily at 50 feet per day. The water level is rising at time t = a. [Choose ] [Choose h'(t) < 0 at ta h'(t) > 0 at ta h'(t) > 0 and h'' (t) < 0 when t = a. h(t) = 50 for t = a h'(t) > 0 and h' (t) > 0 when t = a. h' (t) 50 for 1 t 2 h (t) = 50 for 1 t 2 [Choose ] [Choose ] C++ EXPLAIN WHY! True Or False: A Redefined Member Function Has A Different Signature From The Original Function. Provide the correct IUPAC name for Fe(NO) 6HO short answerlist any four risks and the strategies to mitigate them industrytoday? Develop a business editorial that presents your position on a timely business issue. Support your position with credible references on your topic of interest.InstructionsYour paper should be written using APA style and include, at minimum, the following:A clear statement of the issueA thorough discussion of each of the premisesCredible, supporting evidence for each of the premisesResponse to each of the counterarguments, including evidenceA strong, logical connection between the premises and the conclusionThorough research and documentationWriting that presents a compelling argumentAt least 5 different citations, 3 of which are from the APUS LibraryApproximately 3 to 5 pagesBe certain to carefully research your position using credible sources with proper citations. Follow APA format. You are reviewing the books of a firm you are considering purchasing and notice a considerable difference between the market value of some assets and the book value. Why might there be a difference?If you consider purchasing a firm what is the firms enterprise value based on? (Hint: consider this in terms of the balance sheet entities). Comment on the difference between enterprise value and market value. suppose you consumed a food that contained 2 grams of carbohydrate, 19 grams of fat, 12 grams of protein, and 10 milligrams of vitamin c. how many total kcalories did you consume? according to the writer, what is the best reason to study history? history allows people with different talents to discover one of many paths. history is important to both society and individuals, and it has beauty. history uses several different approaches to find meaning. history is more important to society than to individuals. how to modify sims in cas Which best describes the economy of the middle colonies during the 1600s and 1700s Find the volume of the circular cone in the diagram. (Useas an approximation of pi.)a. 5,544 cubic unitsb. 5,004 cubic unitsC.4,554 cubic units What is the average value of f(x)= 9x 2over the interval 0x3 ? Round your answer to two decimal places. Average value = eTextbook and Media (b) How can you tell whether this average value is more or less than 1.5 without doing any calculations? Since the graph of y= 9x 2is , it lies the line y=3x, so its average value is 1.5 Find all second-order partial derivatives for the function r=ln8x+5y. Find the exact value of the trigonometric expression given thatsin(u)=3/5, where3/2 Q4. Oman is the country for hot water springs. To Construct a Geo thermal power plant, mention the steps you will follow to suggest and build a Geo thermal power plant in Oman. Find the equation of the straight line through the origin and at right angles to the line x ^ 2 - 5xy + 4y ^ 2 = 0 Lynetta and Matas are preparing to open a burger joint called "Lynetta and Matas's Burgers and More Burgers." They are still unclear about the various types of business organizations. Answer the questions to clarify the differences between business organizations. Which business organization can raise capital by issuing stock? O sole proprietorship corporation O partnership Which business organization typically has a single owner that has unlimited liability? Osole proprietorship O partnership corporation Which business organization has unlimited liability and more than one owner? partnership sole proprietorship corporation please help! ch 20\[ \mathrm{Mg}(\mathrm{s})+\mathrm{Cr}^{3}+(\mathrm{aq}) \rightarrow \mathrm{Mg}^{2+}(\mathrm{aq})+\mathrm{Cr}(\mathrm{s}) \] Express your answer as a chemical equation. Identify all of the phases in In process costing, the cost of units finished in the last department will be transferred from Work in Process to: Oa. Sales. Ob. Completed Processes. Oc. Cost of Goods Sold. Od. Finished Goods Assume that a company takes 20,000 hours to produce 80,000 units of a product. What is the velocity for the company? Oa. 4.0 units per hour Ob. 0.25 units per hour Oc. 2.5 units per hour Od. 1 unit per hour Oe, 5 units per hour The Truman Doctrine promised American help to any country that was threatened by the economic and politicalsystem known as