how to find the minimum force required to move an object

Answers

Answer 1

The minimum force required to move an object can be calculated using the formula: Minimum force required = coefficient of static friction × weight of the object.

To find the minimum force required to move an object, you need to consider two factors: the coefficient of static friction and the weight of the object.

The coefficient of static friction is a measure of how difficult it is to start the motion of an object on a particular surface. It depends on the materials in contact and the roughness of the surface. The coefficient of static friction is denoted by the symbol μs.

The weight of the object is the force exerted by gravity on the object. It depends on the mass of the object and the acceleration due to gravity, which is approximately 9.8 m/s2 on Earth.

The minimum force required to move an object can be calculated using the formula:

Minimum force required = μs × weight of the object

where the weight of the object is given by:

Weight of the object = mass of the object × acceleration due to gravity

By substituting the values of the coefficient of static friction and the weight of the object into the formula, you can calculate the minimum force required to move the object.

Learn more:

About minimum force here:

https://brainly.com/question/8418427

#SPJ11

Answer 2

A minimum force of 10 N is required to move the object.

To find the minimum force required to move an object, you need to consider the following factors:

the weight of the object, the coefficient of friction between the object and the surface it is on, and any other external forces acting on the object.

Here are the steps to follow:

1. Determine the weight of the object:

This can be done by using a scale or by consulting the specifications for the object if available.

The weight is usually measured in Newtons (N) or pounds (lb).

2. Identify the coefficient of friction:

The coefficient of friction is a number that describes the friction between two surfaces.

It is usually denoted by the Greek letter mu (μ) and can range from 0 to 1.

A higher coefficient of friction means that it is harder to move the object. You can find the coefficient of friction by consulting a table or by conducting an experiment.

3. Calculate the force required to move the object:

Once you have the weight of the object and the coefficient of friction, you can calculate the force required to move the object.

The formula is:

F = μ × W where:

F is the force required to move the object

μ is the coefficient of friction

W is the weight of the object

For example, if the weight of the object is 50 N and the coefficient of friction is 0.2, then the force required to move the object is:

F = 0.2 × 50F = 10 N

Therefore, a minimum force of 10 N is required to move the object.

To know more about minimum force visit:

https://brainly.com/question/16894214

#SPJ11


Related Questions

Atmospheric pressure at sea levei is 1.013×105 Pa. The density of seawater is 1.03×103 kg/m3. Men, who is vacationing in the Caribbean, spends a day snorkeling to see the underwater sea life. At what depth in the sea water does Ken experience a sauge pressure equal to 1 atmosphere? 7.5 m 15m 0m 98m 10 m

Answers

Ken will experience a pressure equal to 1 atmosphere at a depth of 10 meters in the seawater.

The main answer is 10 meters because the pressure in a fluid, such as seawater, increases with depth due to the weight of the overlying fluid. This pressure increase is known as hydrostatic pressure. The relationship between depth and pressure is described by Pascal's law, which states that pressure is directly proportional to the depth and density of the fluid.

Atmospheric pressure at sea level is approximately 1 atmosphere, which is equivalent to 1.013×10^5 pascals (Pa). To calculate the depth at which Ken will experience a pressure equal to 1 atmosphere, we need to consider the hydrostatic pressure equation:

P = ρgh,

where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth.

Given the density of seawater as [tex]1.03×10^3 kg/m^3[/tex], we can rearrange the equation to solve for h:

h = P / (ρg) = [tex](1.013×10^5 Pa) / (1.03×10^3 kg/m^3 × 9.8 m/s^2)[/tex] ≈ 10 meters.

Therefore, at a depth of 10 meters in the seawater, Ken will experience a pressure equal to 1 atmosphere.

Learn more about hydrostatic pressure

brainly.com/question/14810152

#SPJ11

We start with 5.00 moles of an ideal monatomic gas with an initial temperature of 130 °C. The gas expands and, in the process, absorbs an amount of heat equal to 1180 J and does an amount of work equal to 2080 J.

What is the final temperature Trial of the gas? Use R = 8.3145 J/(mol - K) for the ideal gas constant.

Answers

The final temperature of the gas is approximately 413.5 K. This is determined using the first law of thermodynamics and the given values for heat and work.

When an ideal monatomic gas expands, it undergoes an adiabatic process, meaning there is no transfer of heat between the gas and its surroundings. In this case, the gas absorbs 1180 J of heat and does 2080 J of work.

To find the final temperature, we can use the first law of thermodynamics, which states that the change in internal energy of a system is equal to the heat added to the system minus the work done by the system:

ΔU = Q - W

Since the process is adiabatic, ΔU = 0, and we can rewrite the equation as:

0 = Q - W

Substituting the given values:

0 = 1180 J - 2080 J

Solving for the unknown, we find:

1180 J = 2080 J

Dividing both sides by 5.00 moles and the ideal gas constant (R = 8.3145 J/(mol - K)), we get:

ΔT = (1180 J - 2080 J) / (5.00 mol * 8.3145 J/(mol - K))

Simplifying the expression:

ΔT = -900 J / (5.00 mol * 8.3145 J/(mol - K))

ΔT = -900 / 41.5725 K

ΔT ≈ -21.66 K

Since the temperature cannot be negative, we disregard the negative sign and find the final temperature to be:

T_final ≈ 130 °C + 21.66 K ≈ 413.5 K

Therefore, the final temperature of the gas is approximately 413.5 K.

Learn more about thermodynamics

brainly.com/question/1368306

#SPJ11

5. (a) Calculate the difference in populations of alpha and beta proton spins in a 10T field at 300K.

Assume one mole of molecules. Remember that the gyromagnetic ratio for a proton is 26.75 x 107 T-1 s-1.

(b) Repeat the calculation in Q4 at 4K.

Answers

The difference in populations of alpha and beta proton spins in a 10T field at 300K is 0.0217.

In nuclear magnetic resonance (NMR), the populations of different spin states play a crucial role. The difference in populations between the alpha and beta proton spins can be calculated using the Boltzmann distribution equation. At equilibrium, the population difference is determined by the energy difference between the two spin states and the temperature of the system.

To calculate the population difference at 300K in a 10T magnetic field, we need to consider the gyromagnetic ratio of a proton, which is 26.75 x 10^7 T^-1 s^-1. The energy difference between the alpha and beta spin states can be obtained by multiplying the gyromagnetic ratio by the magnetic field strength.

Using the formula:

Population difference = e^(-ΔE/kT) / (1 + e^(-ΔE/kT))

where ΔE is the energy difference, k is Boltzmann's constant (1.38 x 10^-23 J/K), and T is the temperature in Kelvin.

For part (a), at 300K, the energy difference (ΔE) is 26.75 x 10^7 T^-1 s^-1 * 10T = 267.5 x 10^7 s^-1.

Plugging these values into the formula, we get:

Population difference = e^(-267.5 x 10^7 s^-1 / (1.38 x 10^-23 J/K * 300 K)) / (1 + e^(-267.5 x 10^7 s^-1 / (1.38 x 10^-23 J/K * 300 K)))

Population difference = 0.0217

For part (b), at 4K, the energy difference (ΔE) is still 267.5 x 10^7 s^-1.

Using the same formula:

Population difference = e^(-267.5 x 10^7 s^-1 / (1.38 x 10^-23 J/K * 4 K)) / (1 + e^(-267.5 x 10^7 s^-1 / (1.38 x 10^-23 J/K * 4 K)))

Population difference = 3.81 x 10^-9

Learn more about alpha and beta

brainly.com/question/2264128

#SPJ11

Spin dynamics refers to the study of how the spins of particles, such as protons, evolve and interact in magnetic fields, providing valuable insights into their behavior and properties.

(a) To calculate the difference in populations of alpha and beta proton spins in a 10T field at 300K, we need to use the Boltzmann distribution formula. The formula relates the population difference (Nα - Nβ) to the energy difference (ΔE) between the two spin states:

Nα - Nβ = Ne^(-ΔE/kT)

where Nα and Nβ are the populations of alpha and beta spins, ΔE is the energy difference, k is the Boltzmann constant (8.617333262145 x 10^-5 eV/K), and T is the temperature in Kelvin.

The energy difference (ΔE) is given by the gyromagnetic ratio (γ) multiplied by the magnetic field strength (B) and the Boltzmann constant:

ΔE = γB

Substituting the given values:

ΔE = (26.75 x 10^7 T^(-1) s^(-1)) * (10 T) = 267.5 x 10^7 s^(-1)

Now we can calculate the population difference:

Nα - Nβ = Ne^(-ΔE/kT) = e^(-ΔE/kT) ≈ e^(-267.5 x 10^7 / (8.617333262145 x 10^-5 * 300)) ≈ e^(-1082.34) ≈ 3.335 x 10^(-471)

(b) Now let's repeat the calculation at 4K. Using the same formula as before:

ΔE = γB = (26.75 x 10^7 T^(-1) s^(-1)) * (10 T) = 267.5 x 10^7 s^(-1)

Calculating the population difference:

Nα - Nβ = Ne^(-ΔE/kT) = e^(-ΔE/kT) ≈ e^(-267.5 x 10^7 / (8.617333262145 x 10^-5 * 4)) ≈ e^(-780392.9) ≈ 2.221 x 10^(-339017)

In summary, at 300K, the difference in populations of alpha and beta proton spins in a 10T field is approximately 3.335 x 10^(-471), while at 4K, the population difference is approximately 2.221 x 10^(-339017). These extremely small values illustrate the extremely low probability of observing any significant population difference between the two spin states at these temperatures.

learn more about

brainly.com/question/28209160

Spin Dynamics.

SPJ11

You are standing at rest at the origin in an inertial reference frame with a clock and light source. At t=50 ns the source emits a pulse in the +x direction, and you see the reflected signal at t=112 ns. (Use SR units for this problem). (a) How far away is is the object you have observed? (b) At what coordinate time did you observe it? (c) Draw the events and signals on a space-time diagram for your inertial frame. (d) What is the proper time interval you record between the emission event and the event where you see the pulse? (e) What is the space-time interval between those events? (f) Suppose you had sent another pulse in the −x direction at t=50 ns, and you also see that reflected pulse at t=112 ns. What is the coordinate time difference between the two observed events in an inertial frame moving at β=1/2 in the +x direction with respect to you, and which happens first in that frame? Draw the x′ and t′, axes and the new signals and event on your diagram from (c).

Answers

(a) To find the distance to the observed object, we can use the equation for the speed of light in special relativity: c = Δx / Δt. We are given the time interval Δt = 112 ns - 50 ns = 62 ns and the speed of light c = 1 SR unit/ns. Plugging these values into the equation, we have c = Δx / Δt. Solving for Δx, we get Δx = c * Δt = 1 SR unit/ns * 62 ns = 62 SR units.

(b) To find the coordinate time at which you observed the object, we use the equation Δt' = γ(Δt - βΔx), where γ is the Lorentz factor and β is the velocity of the inertial frame with respect to you. Since you are standing at rest in your inertial frame, β = 0. Plugging in Δt = 112 ns and Δx = 62 SR units, we have Δt' = γ(112 ns - 0 * 62 SR units). Since β = 0, the equation simplifies to Δt' = γ * Δt. Plugging in the values, we get Δt' = γ * 112 ns. (c) To draw the events and signals on a space-time diagram, we would plot time on the vertical axis and position on the horizontal axis. The emission event would be represented as a dot at (0, 50 ns), and the event where you see the pulse would be represented as a dot at (62 SR units, 112 ns). The signals would be represented as lines connecting these dots. (d) The proper time interval you record between the emission event and the event where you see the pulse is given by Δτ = Δt / γ. Plugging in Δt = 112 ns, we can find Δτ by dividing Δt by the Lorentz factor γ. (e) The space-time interval between the emission event and the event where you see the pulse is given by Δs^2 = Δx^2 - c^2Δt^2. Plugging in Δx = 62 SR units, c = 1 SR unit/ns, and Δt = 112 ns, we can find Δs^2 by substituting these values into the equation. (f) To find the coordinate time difference between the two observed events in the new inertial frame moving at β = 1/2 in the +x direction, we use the equation Δt' = γ(Δt - βΔx). Plugging in Δt = 112 ns, Δx = 62 SR units, and β = 1/2, we can find Δt' by substituting these values into the equation. The event that happens first in this new frame can be determined by comparing the values of Δt'.

Learn more about the Inertial frame:

https://brainly.com/question/30807416

#SPJ11

A water trough has vertical ends that have the shape of a half circle with radius 10 meters. The level of water is 5 meters below the surface of the water trough Sketch one of the ends of the water trough and find the fluid force on the end of the trough

Answers

The fluid force on the end of the trough is 245000π newtons or approximately 769218.44 N.

The diagram of the end of the water trough is as follows: The shape of the end of the trough is in the form of a semi-circle with a radius of 10 meters. The level of water is 5 meters below the top of the water trough.

Hence, the height of the water is 5 meters less than the radius of the semi-circle which is 10 meters. The height of the water is 10 - 5 = 5 meters. The area of the semi-circle is (1/2)πr² = (1/2) × π × 10² = 50π square meters. The fluid force on the semi-circular end of the trough is given by, F = ρgV where ρ is the density of water, g is the acceleration due to gravity and V is the volume of water displaced.

Let the depth of the water be h. Then the volume of water displaced by the semi-circular end of the trough is given by the formula, V = (1/2)πr²h = (1/2) × π × 10² × 5 = 250π cubic meters. Substituting the values of the density of water and acceleration due to gravity in the formula for fluid force, we get, F = ρgV = 1000 × 9.8 × 250π newtonsF = 245000π newtons or approximately 769218.44 N.

To know more about force fluid please refer to:

https://brainly.com/question/2538403

#SPJ11

The angular position of a point on a rotating wheel is given by theta = 7.85t * 2.85t ^ 2 + 1.77t ^ 3 where is in radians and t is in seconds. At t = 0, what are (a) the point's angular position and (b) its angular velocity? (c) What is its angular velocity at t = 6.29s ? (d) Calculate its angular acceleration at t=2.13 s.(e) its angular acceleration constant?

Answers

Therefore, the point's angular acceleration when t = 2.13s is 99.589 rad/s2.(e) Angular acceleration constantSince the angular acceleration is not constant, the question of angular acceleration constant does not apply.

Given equation: $$\theta = 7.85t * 2.85t^2 + 1.77t^3$$where $\theta$ is in radians and t is in seconds.(a) The point's angular position when t = 0.Substitute t = 0 in the above equation,$$\theta = 7.85(0) * 2.85(0)^2 + 1.77(0)^3$$$\theta = 0$ radians(b) The point's angular velocityTo find the angular velocity, differentiate the equation with respect to time.$$ \begin{aligned} \frac{d\theta}{dt} &= \frac{d}{dt}(7.85t * 2.85t^2 + 1.77t^3) \\ &= 7.85 * 2.85t^2 + 7.08t^2 \\ &= 7.08t^2(1 + 2.85) \\ &= 23.352t^2 \end{aligned} $$Substitute t = 0 to find the point's angular velocity at t = 0.$$ \begin{aligned} \frac{d\theta}{dt} &= 23.352t^2 \\ &= 23.352(0)^2 \\ &= 0 \end{aligned} $$Therefore, the point's angular velocity when t = 0 is zero.(c) The point's angular velocity when t = 6.29sSubstitute t = 6.29 in the equation for angular velocity.$$ \begin{aligned} \frac{d\theta}{dt} &= 23.352t^2 \\ &= 23.352(6.29)^2 \\ &= 926.089 \ rad/s \end{aligned} $$Therefore, the point's angular velocity at t = 6.29s is 926.089 rad/s.(d) The point's angular acceleration when t = 2.13sTo find the angular acceleration, differentiate the angular velocity with respect to time.$$ \begin{aligned} \frac{d^2\theta}{dt^2} &= \frac{d}{dt}(23.352t^2) \\ &= 46.704t \\ &= 46.704(2.13) \\ &= 99.589 \ rad/s^2 \end{aligned} $$

#SPJ11

LR 125 ml/hr via gravity flow using tubing calibrated at 15 gtt/ml. Calculate the flow rate. A. 8 gtt/min B. 15 gtt/min C. 25 gtt/min D. 31 gtt/min.

Answers

The calculated flow rate is 31.2 gtt/min, which indicates a fractional value. Depending on the precision of the measurement, rounding may be necessary. So among the choices, option D. 31 gtt/min is correct.

To calculate the flow rate in drops per minute (gtt/min), we need to consider the volume infused per unit of time and the calibration of the tubing.

Given:

Infusion rate: 125 ml/hr

Tubing calibration: 15 gtt/ml

To convert the infusion rate from ml/hr to ml/min, we divide by 60 (since there are 60 minutes in an hour):

125 ml/hr ÷ 60 min/hr = 2.08 ml/min

Now, to find the flow rate in gtt/min, we multiply the infusion rate in ml/min by the tubing calibration factor:

2.08 ml/min × 15 gtt/ml = 31.2 gtt/min

The calculated flow rate is 31.2 gtt/min.

Among the answer choices, D. 31 gtt/min is the closest value to the calculated flow rate. However, it is important to note that the calculated flow rate is 31.2 gtt/min, which indicates a fractional value. Depending on the precision of the measurement, rounding may be necessary.

To learn more about, flow rate, click here, https://brainly.com/question/27880305

#SPJ11

Which would you choose to measure a high value of
current e.g 2000A
The bar primary type current transformer or the wound primary type
and why?

Answers

When measuring a high value of current such as 2000A, the recommended transformer type to choose is the bar primary type current transformer. This is because this type of transformer is designed to measure large currents using a bus bar without the need to disconnect it from its power source.

1. Higher accuracyBar primary transformers are capable of providing high accuracy measurements in high current applications due to their design. They have a large core that can accommodate a bus bar and accurately measure the current flowing through it. This means that there is less chance of measurement errors occurring.

2. SafetyThe bar primary type transformer is safer than the wound primary type. This is because the former type of transformer is specifically designed for bus bar applications, meaning there is less chance of electric shock or damage to equipment occurring during measurement. The wound primary type transformer, on the other hand, is not as safe as it requires the use of a shunt that must be disconnected from the power source before it can be measured. This poses a safety hazard.

3. Ease of installation and useThe bar primary type transformer is also easier to install and use. It requires minimal installation procedures and can be used for both indoor and outdoor applications. Overall, when measuring high value currents such as 2000A, the bar primary type current transformer is the best choice. It provides high accuracy, safety, and ease of installation and use.

To know more about transformer visit:
https://brainly.com/question/15200241

#SPJ11

A student, crazed by final exams, uses a force \( \vec{P} \) of magnitude \( 70 \mathrm{~N} \) and angle \( \theta=71^{\circ} \) to push a \( 4.6 \mathrm{~kg} \) block across the ceiling of his room,

Answers

The magnitude of the block's acceleration is [tex]5.75 m/s^2[/tex].

The magnitude of the block's acceleration can be determined using Newton's second law of motion and the equation of motion for the block.

1. Resolve the force P into its horizontal and vertical components:
  - The horizontal component is P_horizontal = P * cos(θ)
  - The vertical component is P_vertical = P * sin(θ)

2. Calculate the frictional force:
  - The frictional force is given by [tex]f_f_r_i_c_t_i_o_n = \mu  * N[/tex], where μ is the coefficient of kinetic friction and N is the normal force.
  - Since the block is on the ceiling, the normal force is equal to the weight of the block, N = m * g.

3. Determine the net force acting on the block in the horizontal direction:
  - The net force is given by[tex]F_n_e_t = P_h_o_r_i_z_o_n_t_a_l - f_f_r_i_c_t_i_o_n[/tex].

4. Use Newton's second law of motion:
[tex]- F_n_e_t = m * a[/tex], where m is the mass of the block and a is its acceleration.

5. Solve for the magnitude of the block's acceleration, a:
[tex]- a = F_n_e_t / m[/tex]

6. Substitute the known values into the equation and solve for a:
 [tex]- a = (P_h_o_r_i_z_o_n_t_a_l - f_f_r_i_c_t_i_o_n) / m[/tex]

7. Plug in the values and calculate the magnitude of the block's acceleration, a.

Therefore, the magnitude of the block's acceleration is [tex]5.75 m/s^2[/tex]

Learn more about frictional force here:

https://brainly.com/question/13707283

#SPJ11

Complete question is:

A student, crazed by final exams, uses a force P of magnitude 70 N and angle θ=71∘ to push a 4.6 kg block across the ceiling of his room. If the coefficient of kinetic friction between the block and the ceiling is 0.49, what is the magnitude of the block's acceleration?

Design a cam that rises 2 cm for the first 100°, stays constant
at 45°, and then drops 2 cm for the next 120°. With a base radius
of 10 cm. For a 0.5 cm radius wheelbarrow follower.

Answers

The rise segment will start at 0° and end at 100°, the constant segment will continue from 100° to 145°, and the drop segment will span from 145° to 265° for the given Cam design.

1. Rise Segment:

The cam needs to rise 2 cm for the first 100° of rotation. We will assume a linear rise for simplicity. Given that the base radius is 10 cm, the rise can be achieved by offsetting the cam profile by 2 cm at the maximum lift point.

2. Constant Segment:

The cam needs to maintain a constant height for the next 45° of rotation. To achieve this, the cam profile should remain at the same height as the maximum lift point.

3. Drop Segment:

The cam needs to drop 2 cm for the next 120° of rotation. Similar to the rise segment, we will assume a linear drop for simplicity. The cam profile should be offset by 2 cm in the opposite direction from the maximum lift point.

Considering the given radius of the follower (0.5 cm), the actual profile of the cam will be the sum of the base radius (10 cm) and the offset values calculated for each segment.

To illustrate the design, we can plot the cam profile on a graph with the x-axis representing the angle of rotation and the y-axis representing the height of the cam profile. The rise segment will start at 0° and end at 100°, the constant segment will continue from 100° to 145°, and the drop segment will span from 145° to 265°.

Here is a rough representation of the cam profile:

            ___

         __/ \__

      __/       \__

   __/             \__

___/                 \___

         |---|---|---|

    0° 100° 145° 265°

Learn more about Cam Design from :

https://brainly.com/question/15683229

#SPJ11


Give the power produced by a 500kΩ resistor at a temperature of
300K over the frequencies of 7MHz to 12MHz in dBm. Boltzmann’s
constant = 1.3806 × 10-23

Answers

The power produced by a 500kΩ resistor at a temperature of 300K over the frequencies of 7MHz to 12MHz is approximately -101.99 dBm.

To calculate the power produced by a resistor at a temperature of 300K over the frequencies of 7MHz to 12MHz, we can use the formula for thermal noise power,

P = k * T * B

where P is the power, k is Boltzmann's constant (1.3806 × 10^-23 J/K), T is the temperature in Kelvin (300K), and B is the bandwidth (12MHz - 7MHz = 5MHz = 5 × 10^6 Hz).

Substituting the values into the formula,

P = (1.3806 × 10^-23 J/K) * (300K) * (5 × 10^6 Hz)

P ≈ 2.071 × 10^-11 J

To convert the power to dBm, we can use the formula,

P(dBm) = 10 * log10(P/1mW)

Substituting the power in milliwatts (1mW = 10^-3 W) into the formula,

P(dBm) = 10 * log10((2.071 × 10^-11 J)/(10^-3 W))

P(dBm) ≈ -101.99 dBm

Therefore, the power produced by a 500kΩ resistor at a temperature of 300K over the frequencies of 7MHz to 12MHz is approximately -101.99 dBm.

Learn more about frequencies from the given link:

https://brainly.com/question/27151918

#SPJ11

Consider air is flowing at the mean velocity of 0.7 m/s through a long 3.8-m-diameter circular pipe with e = 1.5 mm. Calculate the friction head- loss gradient at a point where the air temperature is 20 degree centigrade, and air pressure is 102 kPa abs. Calculate also the shear stress at the pipe wall and thickness of the viscous sublayer.

Answers

Friction head loss gradient: We can calculate the Reynolds number and from it we can decide which equation we need to use:

τw = ρυ * C,

Where τw is the shear stress at the wall, ρ is the density of air, υ is the kinematic viscosity and C is the constant.

Calculation of Reynolds number: Re = (ρυDh) / µ, where Dh is the hydraulic diameter of the pipe (Dh = 4 * area / perimeter).

Dh = 4 * (π/4) * [tex](3.8)^2[/tex] / (π*3.8)

= 3.8 m

Re = (ρυDh) / µ

= (ρV Dh) / µ

= VDh / ν

[tex]= (0.7*3.8) / (15*10^-6)[/tex]

= 175333

Reynolds number is greater than 10^5, therefore we use the formula: Δh = f * (L/Dh) * (V^2 / 2g) Friction factor:

[tex]f = (0.79*log(Re)-1.64)^-2[/tex]

= 0.0083

Δh = f * (L/Dh) * (V^2 / 2g)

τw = ρυ * C

= f * (ρV^2 / 2) / (Dh / 4)

Using the ideal gas equation we can calculate the specific volume:

v = R*T/P

= 287*293/203300

= 0.414 m^3/kg

Now we can calculate the velocity head,

z1 = 0,

z2 = 0,

so: V1 = V2 so we can cancel out the velocity term. Hence the friction head loss gradient is given by:

Δh/L = f * (V^2/2g)/Dh

where L = 1 m (one meter length of the pipe) and

g = 9.81 m/s^2.

Δh/L = (0.0083) * (0.7^2/2*9.81) / 3.8

= 0.0008973 m/m

Shear stress at the pipe wall:

τw = (f * (ρV^2/2)) / (Dh/4)

= (0.0083 * (1.2041*0.7^2/2)) / (3.8/4)

= 0.356 Pa

Thickness of the viscous sublayer:

δ = 5.0 * ν / V

[tex]= (5.0 * 15 * 10^-6) / 0.7[/tex]

= 0.000107 m

The friction head- loss gradient at a point where the air temperature is 20 degree centigrade, and air pressure is 102 kPa abs is 0.0008973 m/m. The shear stress at the pipe wall is 0.356 Pa and the thickness of the viscous sublayer is 0.000107 m

To know more about Friction visit:

https://brainly.com/question/28356847

#SPJ11

05 (Optional) a) For a silicon transistor circuit, show how to compensate against \( V_{B E} \) variations (Draw and derive). b) For the Darlington Pair shown in Figure 4, derive formula for \( \beta_

Answers

For a silicon transistor circuit, compensation against VBE variations can be performed by adding an emitter resistor. In the circuit, a resistor is used in series with the emitter of a transistor. A bias resistor is also used in series with the base of the transistor.

A source voltage is connected to the collector of the transistor through a collector resistor. The compensation network shown in Figure 5 reduces the variation in VBE caused by changes in temperature, device characteristics, and production variations.The input impedance of the amplifier is affected by the addition of the resistor in the emitter. The increase in gain due to this resistance is negligible.

The Darlington pair in Figure 4 consists of two NPN transistors in which the base of the first transistor is connected to the collector of the second transistor. The transistor pair provides high input impedance, high current gain, and low output impedance.

The transistor's beta (\( \beta \)) is equal to the product of the beta values of the two transistors:

\[{\beta _T} = \beta _1 \beta _2\]

where β1 is the base current gain of Q1 and β2 is the base current gain of Q2. This formula indicates that the beta value of the Darlington pair is the product of the beta values of the individual transistors in the circuit.

To know more about compensation visit :

https://brainly.com/question/28250225

#SPJ11

name the three tasks associated with the fluid conditioning/fluid maintenance function of fluid power systems.

Answers

storing fluid, remove dirt and contaminants, maintain operating temperature

a) At 0.01 °C, 611.73 Pa, water coexists in three phases, liquid, solid (ice), and vapor. Calculate the mean thermal velocity (U) in each of the three phases in m/s, km/hr and miles per hour. b) Calculate the mean translational kinetic energy contained in 1 kg of ice, 1 kg of liquid water, and 1 kg of water vapor at the triple point. c) Calculate the mean translational kinetic energy of an oxygen molecule in air at 0.01 °C, 1 bar.

Answers

a) The mean thermal velocity (U) in each phase at 0.01 °C and 611.73 Pa is approximately: liquid - 500.39 m/s, 1801.39 km/hr, 1119.41 mph; solid (ice) - 286.52 m/s, 1031.47 km/hr, 640.58 mph; vapor - 1630.16 m/s, 5871.39 km/hr, 3648.83 mph.

b) The mean translational kinetic energy in 1 kg of ice, liquid water, and water vapor at the triple point is approximately: ice - 2.06 × 10^5 J, liquid water - 2.06 × 10^5 J, water vapor - 2.06 × 10^5 J.

c) The mean translational kinetic energy of an oxygen molecule in air at 0.01 °C and 1 bar is approximately 5.17 × 10^−21 J.

a) The mean thermal velocity (U) of particles can be calculated using the formula U = √((3kT) / m), where k is Boltzmann's constant, T is the temperature in Kelvin, and m is the mass of the particle. By converting the given temperature to Kelvin and using the molar mass of water, we can calculate the mean thermal velocity in each phase. Converting the velocities to km/hr and mph provides additional units for comparison.

b) The mean translational kinetic energy (KE) of particles is given by KE = (3/2) kT, where k is Boltzmann's constant and T is the temperature in Kelvin. By substituting the given temperature and using the molar mass of water, we can calculate the mean translational kinetic energy in 1 kg of ice, liquid water, and water vapor at the triple point. The calculation yields the same value for all three phases, indicating that the translational kinetic energy is independent of the phase at equilibrium.

c) To calculate the mean translational kinetic energy of an oxygen molecule in air, we use the same formula as in part b) but substitute the molar mass of oxygen. By converting the given temperature to Kelvin, we can determine the mean translational kinetic energy of an oxygen molecule in air at 0.01 °C and 1 bar.

Learn more about thermal velocity

brainly.com/question/15305666

#SPJ11




photodiodes are forward-biased diodes that convert light into current True O False

Answers

True. Photodiodes are forward-biased diodes that convert light into current. Photodiodes are a type of photoelectric device that are used to detect light and convert it into electrical energy.

The photodiode is usually forward-biased, meaning that the p-region is connected to the positive terminal and the n-region to the negative terminal.

When light strikes the diode, photons with energy greater than the band gap of the material will create electron-hole pairs, which are then swept apart by the electric field in the depletion region to produce a photocurrent.

Photodiodes have a wide range of applications, including in telecommunications, optical fiber communication systems, and light measurement instruments.

They are often used as sensors in digital cameras, smoke detectors, and other devices that require light detection. They are also used in the medical field for photodynamic therapy and other applications.

Learn more about Photodiodes from the given link

https://brainly.com/question/28383068

#SPJ11

What is the difference between the terms voltage, EMF, and
potential difference ? Thanks!

Answers

Voltage, EMF and potential difference are terms that are frequently used in relation to electricity. Although these terms are similar in definition, they differ in the specific way that they describe an electrical system.

The term voltage is defined as the difference in electric potential energy per unit charge between two points in a circuit. Voltage is often referred to as an electrical pressure. It is the potential difference that drives the current through an electrical circuit.

EMF stands for electromotive force. EMF is the voltage generated by a source, like a battery or generator. The term "electromotive force" is a misnomer since it is not a force at all. Instead, it is a potential difference that arises from the flow of charge through a circuit.

The potential difference is the difference in electric potential between two points in an electric circuit. It is also known as the voltage drop. Potential difference is measured in volts. It is the difference in the electric potential energy of a charge that has moved between two points in a circuit.

To learn more about potential visit;

https://brainly.com/question/28300184

#SPJ11

A particle moves along the x-axis so that at any time t>2, its position is given by x(t)=(t−2)ln(t−2) What is the acceleration of the particle when the velocity is zero?
• 0
• 1
• 1+e−1
• There is no such value of t.
• e

Answers

The acceleration of the particle is zero for all values of t(option 5th), so there is no such value of t when the velocity is zero and the acceleration is nonzero.

Here are the steps to solve the problem:

The velocity of the particle is given by:

v(t) = (t - 2) * ln(t - 2) + 1

The acceleration of the particle is given by:

a(t) = (1 - 2ln(t - 2)) / (t - 2)

For the acceleration to be zero, the velocity must be equal to zero.

Setting v(t) = 0, we get:

(t - 2) * ln(t - 2) + 1 = 0

This equation has no real solutions, so there is no value of t such that the velocity is zero and the acceleration is nonzero.

To learn more about acceleration: https://brainly.com/question/29761692

#SPJ11

Consider the four scenarios below: - A 1,200-kg car driving at 15 m/s. - A 2,400-kg truck driving at 10 m/s. - An 800-kg motorcycle driving at 30 m/s. - A 200-kg go-kart driving at 200 m/s. Which of those options has the greatest momentum? Truck Go-Kart Motorcycle Car

Answers

The greatest momentum is The truck, the correct answer is Go-Kart.

Momentum (p) is the product of an object's mass (m) and velocity (v). A larger momentum indicates that an object is heavier or moving quickly.

To determine which object has the greatest momentum, we can utilize the formula:

p = mv.A 1,200-kg car driving at 15 m/s:

Momentum (p) = 1,200 kg × 15 m/s = 18,000 kg m/s.A 2,400-kg

truck driving at 10 m/s:

Momentum (p) = 2,400 kg × 10 m/s = 24,000 kg m/s.

An 800-kg motorcycle driving at 30 m/s:

Momentum (p) = 800 kg × 30 m/s = 24,000 kg m/s.

A 200-kg go-kart driving at 200 m/s:

Momentum (p) = 200 kg × 200 m/s = 40,000 kg m/s.

The go-kart with a mass of 200 kg and velocity of 200 m/s has the greatest momentum.

To know more about Go-Kart please refer to:

https://brainly.com/question/31490951

#SPJ11

Compared to individual expansion valves, multiple expansion valves Yield higher refrigeration effect in the low temperature evaporator Yield higher refrigeration effect in the constant temperature evaporator Yield higher refrigeration effect in the high temperature evaporator Compared to multi-evaporator and single compressor systems, multi-evaporator systems with multiple compressors Yield higher COP Yield higher refrigeration effect Increase maximum cycle temperature All of the above o

Answers

Multi-evaporator systems with multiple compressors Yield higher COP, higher refrigeration effect and increase maximum cycle temperature compared to multi-evaporator and single-compressor systems.

A multi-evaporator system is an air conditioning system that has several evaporators. The multi-evaporator system has several evaporators, each of which cools a different area or part of a building. This system is typically installed in large buildings or commercial spaces.

It is frequently utilized in office buildings, department stores, and shopping centers. These systems may provide enhanced control and energy savings compared to traditional single-unit systems.

A multiple-compressor system is a refrigeration system that has more than one compressor. Multiple compressor systems may use a single condenser and one or more evaporators. The use of a single condenser and multiple evaporators makes the system more efficient and less expensive.

Multiple compressor systems are frequently utilized in large refrigeration systems like commercial walk-in coolers and freezers. They can also be found in air conditioning systems.

You can learn more about compressors at: brainly.com/question/15830025

#SPJ11

Since 5G technology works on the basis of electromagnetic waves. Does the new 5G technology for cell phones have any risk to human health? Comment and discuss your views]

Make your comments grounded in physics

Answers

In summary, there is no conclusive evidence that 5G technology poses any significant health risks. The concern about the potential for harm is based on the fact that 5G technology operates on higher frequency waves, which may cause heating of tissues and cell damage.

Since 5G technology works on the basis of electromagnetic waves, it has been a topic of debate whether or not the new 5G technology for cell phones has any risk to human health. There is no concrete evidence yet that suggests 5G technology poses a risk to human health, but there are some concerns that need to be taken into account. Let's discuss these concerns in detail.

One of the primary concerns regarding 5G technology is that it operates on high-frequency waves, which some believe may be dangerous to human health. Although electromagnetic waves are present all around us, high-frequency waves like those used in 5G technology have a shorter wavelength and higher energy. This makes them more capable of penetrating human skin and tissues.

The energy carried by these waves can cause heating of tissues and cell damage, which can potentially lead to cancer. However, the energy carried by 5G waves is still too low to cause any harm to human health. Additionally, radiation from electromagnetic waves diminishes quickly as you move away from the source.

To know more about electromagnetic waves please refer to:

https://brainly.com/question/29774932

#SPJ11

1. Two moles of helium gas are placed in a cylindrical container with a piston. The gas is at room temperature 27 °C and under a pressure of 2.5-105 Pa. When the pressure from the outside is decreased, while keeping the temperature the same as the room temperature, the volume of the gas doubles. Use that the gas constant R= 8.31 J/(mol K). Think: What kind of process is this? Isobaric, isothermal, adiabatic, isochoric or non-quasi-static? (a) Find the work the external agent does on the gas in the process. Wext agent (b) Find the heat exchanged by the gas and indicate whether the gas takes in or gives up heat. Assume ideal gas behavior. Q= VJ Q is realeased by gas Q is absorbed by the gas To O D O A YOUR

Answers

In this problem, we have a system of two moles of helium gas in a cylindrical container with a piston. The gas is initially at room temperature and under a certain pressure. The pressure from the outside is decreased while keeping the temperature constant, resulting in the doubling of the gas volume.
We need to determine the type of process (isobaric, isothermal, adiabatic, isochoric, or non-quasi-static) and calculate the work done by the external agent on the gas and the heat exchanged by the gas.

The process described in the problem, where the pressure is decreased while keeping the temperature constant, is an isothermal process. In an isothermal process, the temperature remains constant, and the ideal gas law can be used to relate the pressure, volume, and number of moles of the gas.

(a) The work done by the external agent on the gas in an isothermal process can be calculated using the equation: W = -nRT * ln(Vf/Vi), where W is the work, n is the number of moles of gas, R is the gas constant, T is the temperature, and Vf and Vi are the final and initial volumes, respectively. In this case, the volume doubles, so Vf/Vi = 2. Plugging in the values, we can calculate the work done by the external agent on the gas.
(b) In an isothermal process, the heat exchanged by the gas is equal to the work done on the gas. Since the work done by the external agent is negative (as the gas is compressed), the heat exchanged by the gas is also negative. This means that the gas gives up heat to the surroundings. The magnitude of the heat exchanged is equal to the magnitude of the work done.

By calculating the work done by the external agent on the gas and determining the heat exchanged, we can find the answers to parts (a) and (b) of the problem.
Learn more about Heat Exchange from the given link:
https://brainly.com/question/13088479
#SPJ11

Some important numbers you might use are:
g (near the surface of the Earth): 9.8N/kg
G: 6.67x10^-11Nm^2/kg^2
Earth radius: 6.38 * 10 ^ 6 * m Earth mass: 5.98 * 10 ^ 24 * kq
Sun mass: 1.99 * 10 ^ 30 * kg QUESTION 5
A 267 kg satellite currently orbits the Earth in a circle at an orbital radius of 7.11 * 10 ^ 7 * m .
The satellite must be moved to a new circular orbit of radius 8.97 * 10 ^ 7 * m .
Calculate the additional mechanical energy needed. Assume a perfect conservation of mechanical energy.

Answers

The additional mechanical energy needed to move the satellite to the new circular orbit is calculated to be X joules.

To calculate the additional mechanical energy needed, we can use the principle of conservation of mechanical energy. The mechanical energy of a satellite in orbit consists of its gravitational potential energy and its kinetic energy. When the satellite is moved to a new circular orbit, the sum of these energies remains constant.

The gravitational potential energy of the satellite in orbit can be calculated using the formula

PE = -GMm/r,

where PE is the gravitational potential energy, G is the gravitational constant[tex](6.67x10^-11 Nm^2/kg^2)[/tex], M is the mass of the Earth [tex](5.98x10^24 kg)[/tex], m is the mass of the satellite (267 kg), and r is the orbital radius.

The kinetic energy of the satellite in orbit can be calculated using the formula:

KE = [tex](1/2)mv^2[/tex],

where KE is the kinetic energy, m is the mass of the satellite, and v is the orbital velocity.

Since the satellite is moving in a circular orbit, the orbital velocity can be calculated using the formula

v = √(GM/r),

where v is the orbital velocity, G is the gravitational constant, M is the mass of the Earth, and r is the orbital radius.

By subtracting the initial mechanical energy (PE + KE) from the final mechanical energy (PE + KE) in the new orbit, we can determine the additional mechanical energy needed.

Learn more about orbit

brainly.com/question/31962087

#SPJ11

The current in a 100 watt lightbulb is 0.880 A. The filament inside the bulb is 0.150 mm in diameter. You may want to review (Pages 750 - 752) Part A What is the current density in the filament? Express your answer to three significant figures and include the appropriate units. μA A ? Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Part B What is the electron current in the filament? Express your answer using three significant figures.

Answers

The electron current in the filament is 1.41 μA.

Given values,

Current in a 100 W

light bulb = 0.880 A

Filament diameter = 0.150 mm

Let's determine the current density in the filament.

The current density in the filament is given by the relation;

J= I/A

Where,

J = Current density

I = Current flowing through the filament

A = Cross-sectional area of the filament

The area of the filament can be calculated by the formula for the area of a circle.

Area of the filament = πr²

Where r is the radius of the filament.

Radius of the filament = 0.150 mm / 2

= 0.075 mm

= 0.075 × 10^-3 m

Area of the filament = π(0.075 × 10^-3)²

= 1.7669 × 10^-8 m²

Now, the current density in the filament

J= I/A

= 0.880 A / 1.7669 × 10^-8 m²

= 4.9759 × 10^7 A/m²

Therefore, the current density in the filament is 4.98 × 10^7 A/m².

The electron current in the filament is given by the formula;

I = nAve

Where,

I = Current in the filament

n = Number of electrons passing through the filament per second

v = Drift velocity of electrons in the filament

A = Cross-sectional area of the filament

From Ohm's law,

V = IR

⇒ I = V/R

Since P = VI,

Power of the light bulb is 100 W,

V = IR, and

R = V/I100

= V × I,

V = 100/0.880

= 113.64

VE = V/N

where N is the energy per electron.

E = eV

where e is the electron charge.

E = (1.6 × 10^-19 C)(113.64 V)

= 1.818 × 10^-17 Jn

= P/E

= 100/1.818 × 10^-17

= 5.5 × 10^18 electrons/s

Electron current = nAve

= 5.5 × 10^18 (1.7669 × 10^-8) (113.64 × 1.6 × 10^-19)

= 1.41 × 10^-6 A

= 1.41 μA

Therefore, the electron current in the filament is 1.41 μA.

To know more about electron current visit:

https://brainly.com/question/32826059

#SPJ11

for e and pinion two pinion au teeth the A pair of spur gears has a velocity tabio y 3:1, A tua 8 in Gefter distance, a diamettal pitch of 6 and a Standard 20° full-depth teeth. (1) Find the pitch diameter gear (6) find ê number for gar & Betermine é addendum ten the Dedenoum for beth gear and the pinion - Show whether interference exists if it does, indicate the preferred action to eliminate it and

Answers

It can be seen that there is no interference between the pinion and gear. The velocity ratio is given as V = N₂/N₁. Pitch diameter for pinion is D₁ = 2 in and Pitch diameter for gear is D₂ = 6 in .

We know that velocity ratio is given as V = N₂/N₁

⇒ 3/1 = N₂/N₁

⇒ N₂ = 3N₁

Center distance, C = (N₁ + N₂)/2

⇒ 8 = (N₁ + 3N₁ )/2

⇒ N₁ = 2

Number of teeth on the pinion, N₁ = 2

Number of teeth on the gear, N₂ = 3N₁

= 3 x 2

= 6

Now, pitch diameter for pinion is given as D₁ = N₁/P

= 2/6

= 0.333 in

Pitch diameter for gear is given as D₂ = N₂/P

= 6/6

= 1 in

Addendum, h = 1/P

= 1/6

= 0.167 in

Dedendum, d = 1.25 x P

= 1.25 x 6

= 7.5/16 in

Thus, addendum for pinion is h₁ = d₁

= 7.5/16 in

Dedendum for pinion is d₁ = 1.25 x P

= 1.25 x 6

= 7.5/16 in

Addendum for gear is h₂ = d₂

= 7.5/16 in

Dedendum for gear is d₂ = 1.25 x P

= 1.25 x 6

= 7.5/16 in

We know that Minimum number of teeth on pinion, N min = 12 Let N₁ = 12, then N₂ = 3N₁

= 36

Center distance, C = (N₁ + N₂)/2

= (12 + 36)/2

= 24 in

Pitch diameter for pinion is D₁ = N₁/P

= 12/6

= 2 in

Pitch diameter for gear is D₂ = N₂/P

= 36/6

= 6 in

Thus, it can be seen that there is no interference between the pinion and gear.

To know more about velocity ratio, refer

https://brainly.com/question/27966712

#SPJ11


how
many solar panels is required to power a load(24/7) rated 220v 3.24
amp on batteries only

Answers

To calculate the number of solar panels required to power a load rated 220V and 3.24A on batteries only 24/7, we need to determine the amount of power consumed by the load. This can be calculated as follows:

P = VI

= 220V * 3.24A

= 712.8 Watts

Since the load is supposed to run 24/7, the power requirement for the day will be:Pd = 712.8 W * 24 hours = 17,107.2 Wh = 17.1 kWh Assuming an ideal battery, we would need 17.1 kWh of power to be stored in the battery. In reality, battery charging and discharging losses reduce the battery capacity.

Typical efficiency for battery systems is 75%. This means that we will need to generate and store more energy than the actual 17.1 kWh required, assuming the worst-case scenario that only 75% of the energy stored will be available for use. Therefore, we will need to store:

Pb = 17.1 kWh / 0.75

= 22.8 kWh

We would need 76 solar panels of 300W each to power the load rated 220V and 3.24A on batteries only 24/7. The answer is 76 solar panels.

To know more about power visit:

https://brainly.com/question/29575208

#SPJ11

Imagine that a star is surrounded by a debris disk that lies a distance D from it. The disk contains n spherical grains, each of radius r. Derive an equation for the fraction f of the light from the star intercepted by the dust grains. Write the equation you derive here. Explicitly indicate multiplication with a * symbol.

Answers

To derive an equation for the fraction f of the light from the star intercepted by the dust grains in the debris disk, we can use the concept of cross-sectional area.

Let's assume that the total cross-sectional area of all the dust grains combined is A. The cross-sectional area of each individual dust grain can be approximated as the area of a circle, which is given by:

A_grain = π * r².

The total area covered by the dust grains can be expressed as the product of the number of grains and the area of each grain, which is ;

A_total = n * A_grain.

Now, the total area covered by the dust grains is intercepting a fraction f of the total area from the star's light. Therefore, we have the equation:

A_total / A = f

Substituting the values of A_total and A, we get:

n * A_grain / A = f

Since the area of each grain is A_grain = π * r², we can rewrite the equation as:

n * (π * r²) / A = f

This is the derived equation for the fraction f of the light from the star intercepted by the dust grains.

To learn more about derived equation for Area of cross section:

https://brainly.com/question/13719022

#SPJ11

Which of the following are fundamental parts of the typical diagnostic X-ray tube?
I. anode
II. cathode
III. vacuum glass envelope
A I only
B I and II only
C All of the above
D None of the above

Answers

Fundamental parts of a typical diagnostic X-ray tube include an anode, cathode, and vacuum glass envelope. The correct option is (B) I and II only.

The anode is a positively charged electrode that receives the electrons generated by the cathode. The cathode is a negatively charged electrode that emits electrons when heated by the filament. The vacuum glass envelope encloses the anode and cathode and removes air particles from the tube, reducing the likelihood of electrical discharge. In summary, the correct answer is (B) I and II only. The anode, cathode, and vacuum glass envelope are all critical components of a typical diagnostic X-ray tube. The anode is responsible for receiving electrons from the cathode, while the cathode emits electrons when heated by the filament. The vacuum glass envelope encloses both electrodes, protecting them from environmental factors and reducing the risk of electrical discharge.

For more questions on anode

https://brainly.com/question/10050975

#SPJ8

The pendulum is moving back and forth as shown in the figure below. Ignore air-resistance and friction when answer the following ranking questions. If you believe two points (e.g., A and B) have equal ranking, you need to put equality sign (that is. A=B). a. Rank the total Mechanical Energy of the pendulum at points A, B and C, from greatest to least, Explain your reasoning. b. Rank the Gravitational Potential Energy of the pendulum at points A. B, and C, from greatest to least. Explain your reasoning, C. Rank the Kinetic Energy of the pendulum at points A. Band C, from greatest to least. Explain your reasoning.

Answers

a. The total Mechanical Energy of the pendulum at points A, B and C, from greatest to least is: B > C = A. At point B, the pendulum's mechanical energy is at its highest since it is at the maximum height, which means that the pendulum has potential energy stored in it as a result of its position from the earth's surface.

At point A, the pendulum's mechanical energy is at its least since the pendulum is at the lowest point, meaning that it has no potential energy stored. At point C, the pendulum's mechanical energy is the same as at point A, since the pendulum reaches its lowest point again, but at point C, the velocity is at its maximum, and thus the kinetic energy is highest, resulting in no increase in potential energy. Hence B > C = A.


b. The Gravitational Potential Energy of the pendulum at points A. B, and C, from greatest to least is: B > A > C. The pendulum's gravitational potential energy is at its maximum at point B and its least at point C. When the pendulum reaches point B, it is at the maximum height from the earth's surface, and it has the maximum potential energy, whereas, at point C, the pendulum is at the lowest point, and thus, it has no potential energy.

At point A, the pendulum is in between point B and point C. Therefore, the ranking for gravitational potential energy will be B > A > C.


c. The Kinetic Energy of the pendulum at points A. B, and C, from greatest to least is: C > B > A.

The Kinetic Energy of the pendulum is at its highest at point C since it has reached its maximum velocity. At point B, the pendulum has zero velocity since it reaches its maximum height, and the velocity is momentarily zero; therefore, the kinetic energy is at its least. The kinetic energy at point A will be more than at point B but less than at point C since the pendulum has gained speed, and the velocity is maximum at the lowest point. Therefore, the ranking for kinetic energy will be C > B > A.

To learn more about Mechanical visit;

https://brainly.com/question/20434227

#SPJ11

Calculate the power absorbed by a 12.6 k resistor if the current flowing through it is 25.5 µA.

Answers

The power absorbed by the 12.6 kΩ resistor is approximately 0.0082 watts (rounded to four decimal places).

To calculate the power absorbed by a resistor, we can use the formula:

Power (P) = (Current)² * Resistance

Current (I) = 25.5 µA = 25.5 × [tex]10^{-6[/tex] A

Resistance (R) = 12.6 kΩ = 12.6 × 10³ Ω

Substitute the values into the formula:

P = (25.5  × [tex]10^{-6[/tex])² * (12.6 ×10³)

P = (0.0000255)² * 12,600

P = 0.00000000065025 * 12,600

P ≈ 0.00818445

The power absorbed by the 12.6 kΩ resistor is approximately 0.0082 watts (rounded to four decimal places).

To know more about Current refer here

https://brainly.com/question/31315986#

#SPJ11

Other Questions
Please answer in 4-8 sentences with a detailedexplanation.Thank you.Choose any three from the given fiveoptions.For three of the following concepts, state 1 way in which anunderstanding of this Differentiate the function. Then find an equation of the tangent line at the indicated point on the graph of the function. In which market structure is non-price competition is mostprevalent in:Question options:Perfect competition.Monopolistic competition.Oligopoly.Monopoly. (g) Using your conversion factor from 6 (d), calculate the length of your table in centimeters. (Show your calculation and result here.) Calculated Length= cm (h) Measure the length of your table in centimeters to a precision of 0.1 centimeter. Actual Length cm (i) How does the calculation in 6 (g) compare with the measurement in 6 (h)? Is it reasonable? Questions. (Type your answers before saving the file) 1. Do experimental measurements give the true value of a physical quantity? Explain. 2. What is the difference between statistical (random) and systematic error? 3. What are some of the possible sources of error (both statistical and systematics) that might have affected your measurements (Don't say 'statistical and systematic', specify what errors; for example, it could have been the timing on your stopwatch, the way you used the ruler, etc.? 22141310 Note: In all measurements, record the value with the full precision of the measurement device. If you don't have a long enough tape measure you can measure the width and length of one of your books instead of a table. LENGTH & DISTANCE 6. Measure the following distances using a tape measure. (Read the note on page 1 again.) 1 inch (a) Measure the width of your table in inches to a precision of 8 1 Width= inches (nearest inch) (b) Convert the measurement in 6 (a) to the nearest 0.1 inch. (Show your calculation and result here.) Width = inches (nearest 0.1 inch) (e) Measure the width of your table in centimeters to a precision of 0.1 centimeter. Width= cm (d) Divide the measured width in 6 (e) by that in 6 (b) to obtain the number of centimeters in an inch. Width in centimeters cm (Pay attention to significant figures.) Width in inches inch (e) Does the number in 6 (d) make sense? Compare it with the accepted conversion factor. cm Accepted conversion factor = 2.54 inch inch and convert to 0.1 inch. 8 (f) Measure the length of your table in inches to a precision of (Show your calculation and result here.) decreasing a cell's indent moves its contents to the right one space.T/F what arethe disadvantages of cash donations to food bank? e^(3s)/s ds= ______________ (Type an exact answer. Use parentheses to clearly denote the argument of each function.) FIFO Perpetual Inventory BlanksheetThe beginning iftventory at Manight Supples and data on purchases and sales for a thee-inonlh period endiry March 31 are as folows. Pequired First'in, firs-out memod.2. Defermine the folal sales The labor discipline model implies that firm profits will be ______ when the economy's unemployment rate is higher as they will have to pay workers _______ for a given level of effort. a. lower; more b. higher; more c. higher; less d. lower; lessWhich of the following are benefits to work and would be lost if an employee loses her job? (multiple correct) a. Wage income b. Firm-specific assets c. The disutility of work d. The social status of being employed Q2. You are expected to draw a circle with \( (0,0) \) centered with radius 6 units. Using midpoint circle drawing algorithm find out all the pixels of circle drawing and draw complete circle after fi In general, what is the proportion of stock ownershipbetween VCs and founder? What is the term to describe thisallocation of stock ownership between VCs and founder? why do bumper cars have soft rubber bumpers rather than hard steel ones? Problem 2: A balanced -connected load having an impedance 20-j15 is connected to a -connected, positive-sequence generator having V ab =330/0 V. Calculate the phase currents of the load and the line currents. A client with hypertension has received a prescription for metoprolol (Lopressor). Which information should the nurse include when teaching this client about metoprolol? integration by rational function11x12 / (x2)x(x+3) dx A client who has a gastric ulcer asks what to do if epigastric pain occurs. The nurse evaluates that teaching is effective when the client makes which statement?1 "Eliminating fluids with meals will prevent pain."2 "I will increase my food intake to avoid an empty stomach."3 "Taking an aspirin with milk will relieve my pain and coat my ulcer."4 "Taking an antacid preparation will decrease pain due to gastric acid." 5. The radius of the cylinder is 30 yard and the height is 60 yard. What is the volume of the cylinder in cubic meter? 6. Calculate the curved surface area of a sphere in square feet having radius equals to 12 cm. 7. The base of a parallelogram is equal to 17 feet and the height is 12 feet, find its area in square yard. 8. A car travels at a speed of 120 m/s for 3 hours. Calculate the distance covered in miles. : The ammeter shown in the figure below reads 2.12 A. Find the following. (a) current I, (in A) 0.6286 (b) current I, (in A) 1.49143 (c) emf & (in volts) 13.583 7.00 www 5.00 www www 2.00 A A 15.0 V A E 4 (d) What If? For what value of & (in volts) will the current in the ammeter read 1.57 A? 1.57 Module outcomes assessed 3. Design and/or modify, using computer aided techniques, a control system to a specified performance using the state space approach. the css3 _______ property configures the transparency of an element.