Given data:
Base resistance = 2.2 kΩ
Collector resistance = 4.7 kΩ
Emitter resistance = 1 kΩ
Emitter current = 2.9 mA
(i) Calculation of Base Current:
Current is given as emitter current Ie = 2.9 mA
Voltage across base-emitter junction is Vbe = 0.7 V
Current at the base is given by the formula:
Ib = Ie / β
Where β is the current gain (hfe).
Using the above formula, we get:
Ib = Ie / β
Ic / Ie = β
Ic = β × Ib
Given β = 100
Now, the base current is given by the formula:
Ie = Ib + Ic
Ic = β × Ib
Ib = Ic / β = 2.9 / 100 = 0.029 mA
(ii) Calculation of Collector Current:
The collector current is given by the formula:
Ic = β × Ib
Given β = 100
Ic = β × Ib
Ib = Ic / β = 0.029 / 100 = 0.00029 A (or 0.29 mA)
(iii) Calculation of VCE:
VCE = VCC - Ic × RC
Given RC = 4.7 kΩ, VCC = 9 V, and Ic = 0.29 mA
VCE = VCC - Ic × RC = 9 - 0.29 × 4700 = 6.243 V
(iv) Load Line for the Circuit:
The load line is drawn by using the saturation and cutoff points. The cutoff point is obtained when VCE = VCC, which is 9 V. The saturation point is obtained when IC = 0. VCE in this case is obtained as follows:
VCE(sat) = VCE(on) = 0.2 V
To draw the load line, we need to plot the two points and join them using a straight line. The figure below shows the load line of the given circuit. We can see that the operating point Q lies on the load line between the saturation and cutoff points. The transistor is operating in the active region.
To know more about Voltage visit:
https://brainly.com/question/32002804
#SPJ11
Which of the following is true with respect to WANS? WAN-specific protocols run in all layers of the TCP/IP model. Circuit switching can create end-to-end paths using both Switched Circuits and Dedicated Circuits. WAN providers are private networks and are not a part of the global Internet. Packet Switched leased lines can be obtained from telco providers to connect to the WAN. The local loop refers to the connection from the customer site to the provider network. TDM leases lines can be obtained from telco providers to connect to the WAN.
The following statement is true with respect to WANs: "Packet Switched leased lines can be obtained from telco providers to connect to the WAN."
WANs (Wide Area Networks) are networks that span large geographical areas, connecting multiple locations together. They are designed to facilitate long-distance communication and connectivity between different sites or branches of an organization.
Packet switching is a common technique used in WANs, where data is divided into smaller packets and transmitted independently over the network. Leased lines, specifically Packet Switched leased lines, can be obtained from telecommunications (telco) providers to establish connectivity between different sites in a WAN. These leased lines provide a dedicated connection and ensure reliable and efficient data transmission.
The other statements mentioned in the options are not entirely accurate or are false:
- WAN-specific protocols do not run in all layers of the TCP/IP model. While WANs may use various protocols at different layers of the TCP/IP model, it is not specific to WANs only.
- Circuit switching can create end-to-end paths using either Switched Circuits or Dedicated Circuits, but it is not limited to WANs. Circuit switching can be used in both WANs and LANs.
- WAN providers are not necessarily private networks and are often part of the global Internet. WAN providers can be public or private entities, and they often provide connectivity to the global Internet.
- The local loop refers to the connection from the customer site to the provider network, which is true. It is the physical connection between the customer's premises and the telecommunications infrastructure.
- TDM (Time Division Multiplexing) leased lines can be obtained from telco providers to connect to the WAN, which is true. TDM is a method of transmitting multiple signals over a single communication link, and it can be used to establish leased lines for WAN connectivity.
To summarize, the statement that is true with respect to WANs is that Packet Switched leased lines can be obtained from telco providers to connect to the WAN.
Learn more about WANs here
https://brainly.com/question/29670483
#SPJ11
interface BinNode {public int value();public void setValue(int v);public BinNode left();public BinNode right();public boolean isLeaf();}Write a recursive function that traverses a binary tree and prints the value of every node which has at least two children.public int AtLeastTwoChildren(BinNode root){
The recursive function AtLeastTwoChildren traverses a binary tree and prints the values of nodes that have at least two children.
To implement the AtLeastTwoChildren function, we can use a recursive approach to traverse the binary tree and print the values of nodes that have at least two children. Here's an example implementation in Java:
public int AtLeastTwoChildren(BinNode root) {
if (root == null) {
return 0;
}
int count = 0;
if (root.left() != null && root.right() != null) {
System.out.println(root.value());
count++;
}
count += AtLeastTwoChildren(root.left());
count += AtLeastTwoChildren(root.right());
return count;
}
The function takes a BinNode object as the root of the binary tree and returns the count of nodes that have at least two children. It starts by checking if the current node has both a left child and a right child. If it does, it prints the value of the node and increments the count. Then, the function recursively calls AtLeastTwoChildren on the left and right children of the current node, accumulating the count of nodes with at least two children from the subtree rooted at each child. Finally, the function returns the total count of nodes with at least two children in the binary tree.
learn more about traverses here :
https://brainly.com/question/31176693
#SPJ11
Take a class Person having two attributes name and age. Include a parametrized constructor to give values to all data members. In main function i. Create an instance of the person class and name it person1. ii. Create a binary file person.bin and write person1 object into it. iii. Read the person1 object from the file. iv. Return 0
Here's an example implementation of the Person class with a parameterized constructor and methods for writing and reading objects to/from a binary file:
import java.io.*;
public class Person implements Serializable {
private String name;
private int age;
public Person(String name, int age) {
this.name = name;
this.age = age;
}
public void writeToFile(String fileName) throws IOException {
FileOutputStream fos = new FileOutputStream(fileName);
ObjectOutputStream oos = new ObjectOutputStream(fos);
oos.writeObject(this);
oos.close();
fos.close();
System.out.println("Person object written to file " + fileName);
}
public static Person readFromFile(String fileName) throws IOException, ClassNotFoundException {
FileInputStream fis = new FileInputStream(fileName);
ObjectInputStream ois = new ObjectInputStream(fis);
Person person = (Person) ois.readObject();
ois.close();
fis.close();
System.out.println("Person object read from file " + fileName);
return person;
}
public String toString() {
return "Name: " + name + ", Age: " + age;
}
public static void main(String[] args) {
Person person1 = new Person("John Doe", 30);
try {
person1.writeToFile("person.bin");
Person person2 = Person.readFromFile("person.bin");
System.out.println(person2.toString());
} catch (IOException e) {
e.printStackTrace();
} catch (ClassNotFoundException e) {
e.printStackTrace();
}
}
}
In this implementation, the Person class implements the Serializable interface. The parameterized constructor takes in values for the name and age attributes.
The writeToFile() method writes the current Person object to a binary file using the ObjectOutputStream class. The readFromFile() method reads a Person object from a binary file using the ObjectInputStream class.
In the main function, we create an instance of Person named person1, write it to a binary file called "person.bin", read it back from the file into a new object person2, and then print out the toString() representation of person2.
Note that writing and reading objects to/from binary files in Java requires handling IOException and ClassNotFoundException exceptions.
learn more about binary file here
https://brainly.com/question/31203822
#SPJ11
why do bumper cars have soft rubber bumpers rather than hard steel ones?
Bumper cars have soft rubber bumpers rather than hard steel ones to prevent injury during collisions.
When you ride in a bumper car, the goal is to collide with other cars in a fun and safe manner. For safety reasons, the cars are designed with rubber bumpers that absorb the impact of the collision, preventing riders from being injured.
When two bumper cars collide, the rubber bumpers compress, which absorbs the shock of the impact. If they had hard steel bumpers, the collisions would be a lot more dangerous, and people would be more likely to get hurt or injured in the process.
Additionally, the rubber bumper provides a frictionless surface for the car to move around. This frictionless surface makes it easy for the cars to slide and bump against one another without causing any harm.
Learn more about bumpers at
https://brainly.com/question/29529611
#SPJ11
A-Sn (exists below 13.2 °C) has a cubic structure with lattice parameter a 6.4912 A and a density of 5.769 g/ce (at 0 C). B-Sn has a tetragonal crystal structure with lattice parameter a 5.8316 A, c= 3.1813 A and a density of 7365 g/co (at 30 °C). Determine the number of atoms per unit cell for both a-Sn and ß-Sn and hence determine the percentage volume change that would occur when a-Sn is heated from 0°C to 30°C? The atomic weight of Sn is 118.69 gmol.
(a) Number of atoms per unit cell of a-Sn We know that lattice parameter a = 6.4912Å Volume of the unit cell, V = a³∴V = (6.4912)³V = 274.827 ųDensity of a-Sn = 5.769 g/cm³∴Mass of the unit cell, m = Density × Volume
∴m = 5.769 × (10⁻⁸ × 274.827) Kg
∴m = 0.00001583 Kg Number of atoms in the unit cell can be calculated by the following formula.
Number of atoms in the unit cell, n = (mass of the unit cell/molar mass) × Avogadro's number where Avogadro's number, N = 6.022 × 10²³ Mass of the unit cell = Density × Volume = 5.769 × 10³ × 274.827 × 10⁻²⁴ kg
Molar mass of Sn, M = 118.69 g/mol = 0.11869 Kg/mol Number of atoms in the unit cell of a-Sn = (5.769 × 10³ × 274.827 × 10⁻²⁴ / 0.11869) × 6.022 × 10²³Number of atoms in the unit cell of a-Sn = 2 x 10²²
(b) Number of atoms per unit cell of β-Sn Given lattice parameter a = 5.8316 Å and c = 3.1813 Å
.∴Volume of the unit cell, V = a²cV = (5.8316)² x 3.1813V = 107.29 ų Density of β-Sn = 7.365 g/cm³
∴Mass of the unit cell = Density × Volume = 7.365 × 10³ × 107.29 × 10⁻²⁴ kg Number of atoms in the unit cell of β-Sn = (7.365 × 10³ × 107.29 × 10⁻²⁴ / 118.69) × 6.022 × 10²³ Number of atoms in the unit cell of β-Sn = 2.506 x 10²² Percentage volume change that occurs when a-Sn is heated from 0°C to 30°C is as follows: Change in volume of a-Sn, ΔV = Vf - Vi where Vi is the initial volume of a-Sn and V f is the final volume of a-Sn.
Change in temperature, ΔT = T₂ - T₁ where T₁ = 0°C and T₂ = 30°C Volume expansion coefficient of a-Sn, α = (ΔV/V₀) / ΔT where V₀ is the initial volume of a-Sn. Volume expansion coefficient of a-Sn, α = [(ΔV/V₀) / ΔT] x 100 where ΔV/V₀ is the fractional change in volume. Percentage change in volume of a-Sn when heated from 0°C to 30°C = α x ΔT Percentage volume change = α x ΔT Percentage change in volume of a-Sn when heated from 0°C to 30°C is obtained by using the above formula, where α = 2.1 x 10⁻⁵ K⁻¹ (for Sn) and ΔT = 30°C - 0°C = 30°C.
Percentage volume change = (2.1 × 10⁻⁵ × 30) × 100% Percentage volume change = 0.063% = 0.063 x 274.827 = 0.173 ų (Approx) Therefore, the volume change that occurs when a-Sn is heated from 0°C to 30°C is approximately 0.173 ų.
To Know more about cubic structure with lattice parameter Visit:
https://brainly.com/question/21415575
#SPJ11
Given the lists listi and list that are of the same length, create a new list consisting of the first element of listi followed by the first element of list2, fol lowed by the second element of listi, followed by t he second element of list2, and so on (in other wor ds the new list should consist of alternating elements of listi and list2). For example, if listi contained [1, 2, 3] and list2 contained [4, 5, 6], then the new I ist should contain (1, 4, 2, 5, 3, 6]. Assign the new list to the variable list3.
To create a new list, list3, consisting of alternating elements from listi and list2, you can use a simple loop to iterate through the indices of the lists and append the corresponding elements to list3.
Here's an example of how you can achieve this:python
Copy code
listi = [1, 2, 3]
list2 = [4, 5, 6]
list3 = []
for i in range(len(listi)):
list3.append(listi[i])
list3.append(list2[i])
print(list3)
Output:
csharp
Copy code
[1, 4, 2, 5, 3, 6]
In this example, the loop iterates through the indices of listi (or list2 since they have the same length) using the range(len(listi)) expression. For each index i, it appends the i-th element of listi followed by the i-th element of list2 to list3. Finally, we print list3 to verify the result.
Learn more about alternating here:
https://brainly.com/question/33068777
#SPJ11
You have been asked to use a proportional controller to make a stable closed-loop system. The transfer function of the plant is:
C(s) = s² +1 / s(s² + 4s + 4) (s² + 2s + 1)
Write the characteristic equation of the closed-loop system as a function of both K and s.
The characteristic equation of the closed-loop system as a function of both K and s is 0.
Given transfer function of the plant C(s): $$C(s) = \frac{s^2 +1}{s(s^2 + 4s + 4)(s^2 + 2s + 1)}$$
The transfer function of the closed loop system is given by: $$T(s) = \frac{G_c(s)G_p(s)}{1 + G_c(s)G_p(s)}$$
where T(s) is the transfer function of closed loop system, Gc(s) is the transfer function of the controller and Gp(s) is the transfer function of the plant.
So, the characteristic equation of the closed-loop system can be written as: $$1 + G_c(s)G_p(s) = 0$$
Substituting the transfer functions of Gc(s) and Gp(s), we get: $$1 + K \frac{Y(s)}{R(s)} \frac{s^2 +1}{s(s^2 + 4s + 4)(s^2 + 2s + 1)} = 0$$
where Y(s) is the output of the plant and R(s) is the input to the system.
Rearranging the terms, we have: $$s^6 + 7s^4 + 12s^3 + (4 + K)s^2 + 7s + K = 0$$
Therefore, the characteristic equation of the closed-loop system as a function of both K and s is: s^6 + 7s^4 + 12s^3 + (4 + K)s^2 + 7s + K = 0.
To know more about closed-loop system refer to:
https://brainly.com/question/11995211
#SPJ11
Algorithm Design Consider the problem of finding the distance between the two closest numbers in an array of n numbers, such as "45,58, 19, 4, 26, 65, 32,81". (The distance between two numbers x and y is computed as x - y Design a presorting-based algorithm (10 points, implementing in C++, for sorting algorithm, you can just make a call to the quicksort algorithm you implemented in question 1) for solving this problem and determine its efficiency class
To solve the problem of finding the distance between the two closest numbers in an array, we can follow the presorting-based algorithm as described below:
1. Sort the array in non-decreasing order using a sorting algorithm (e.g., quicksort).
2. Initialize a variable "minDistance" to a large value.
3. Iterate through the sorted array from left to right:
- Calculate the distance between the current element and the next element.
- If the calculated distance is smaller than the current minimum distance, update the minimum distance.
4. The final value of "minDistance" will be the distance between the two closest numbers in the array.
The efficiency class of this algorithm can be determined as follows:
- Sorting the array takes O(n log n) time complexity in the average case (using quicksort).
- The subsequent iteration through the sorted array takes O(n) time complexity.
- Therefore, the overall time complexity of this algorithm is O(n log n) + O(n) = O(n log n).
In terms of space complexity, the algorithm requires O(n) space to store the sorted array.
By applying the presorting-based algorithm, we can efficiently find the distance between the two closest numbers in the array with a time complexity of O(n log n), where n is the size of the array.
Learn more about problem here:
https://brainly.com/question/31816242
#SPJ11
For the circuit given below i) Find the Thevenin equivalent circuit (i.e. Thevenin voltage and Thevenin equivalent impedance) from terminals a to \( b \). ii) Determine the impedance \( Z_{L} \), that
i) To find the Thevenin equivalent circuit, we'll follow these
steps:1. Disconnect the load resistor, RL, from the rest of the circuit.2.
Find the equivalent resistance by reducing the resistors to a single resistor. 3. Calculate the voltage across the terminals, a and b.4. Draw the Thevenin equivalent circuit using the equivalent resistance as the impedance, ZTh, and the voltage across the terminals, VTh.
ii) To determine the impedance, ZL, we need to first calculate the current, IL. To do this, we can use
Ohm's Law:IL = VTh/ZThIL = 2V/20Ω
IL = 0.1A[tex]Ohm's Law:IL = VTh/ZThIL = 2V/20ΩIL = 0.1A[/tex]
From here, we can calculate the voltage across the load resistor, RL:
[tex]VL = IL * RLVL = 0.1A * 100ΩVL = 10V.[/tex]
To know more about equivalent visit:
https://brainly.com/question/25197597
#SPJ11
Q1 (a) With aid of suitable diagram, explain the losses and power-flow of an induction motor. (b) A three-phase, 50 Hz, four poles induction motor runs at a no-load speed of 1350 r/min and full-load speed is 1200 r/min.
(i) Calculate the slip of the rotor at no-load and full-load conditions.
(ii) Based on Q1(b)(i) results, calculate the electrical frequency of the rotor at no-load and full-load conditions.
(iii) Calculate the speed regulation of this motor.
Q1(a) Losses and power flow of an induction motor
The three-phase induction motor has three stator winding phases displaced by 120 degrees in space and is wound on the stator poles.
The rotor of the motor is wound on the rotor poles and is supplied by AC power from the stator winding that induces a current in the rotor winding.
The power flow and losses are illustrated in the below diagram:
(i) At no-load, the rotor runs at a speed equal to the synchronous speed because the rotor is not loaded with any torque, so it does not slip.
As a result, the rotor speed of 1350 r/min is equal to the synchronous speed (Ns) at a frequency of 50 Hz.
(ii) At full load, the rotor has a slip of 11.11%, which is calculated as follows:
Slip, s = (Ns - N) / Ns
Where,
Ns = 120
f/P = 120 × 50/4
= 1500 r/min
N = full-load speed
= 1200 r/mins
= (1500 - 1200) / 1500
= 0.2
The electrical frequency of the rotor at no-load is 50 Hz, and at full-load, it is 45 Hz.
Since the rotor frequency is proportional to the slip, we can calculate the rotor frequency at no-load and full-load as:
f1 = (1 - s) × f
= (1 - 0) × 50
= 50 Hz
f2 = (1 - s) × f
= (1 - 0.2) × 50
= 40 Hz
(iii) Speed regulation of the motor can be calculated as follows:
Speed regulation,
R = (N1 - N2) / N2 × 100%
Where, N1 = no-load speed
= 1350 r/min
N2 = full-load speed
= 1200 r/min
R = (1350 - 1200) / 1200 × 100%
= 12.5%
Therefore, the speed regulation of the motor is 12.5%.
To know more about speed visit:
https://brainly.com/question/17661499
#SPJ11
Write a c program to design an electrical circuit with one voltage source and one current source to find the value of resistance.
The given C program calculates the value of resistance in an electrical circuit based on user-input voltage and current values using Ohm's law (V = IR).
Here's an example of a C program that designs an electrical circuit with one voltage source and one current source to calculate the value of resistance:
``c
#include <stdio.h>
int main() {
float voltage, current, resistance;
// Input voltage and current values
printf("Enter the voltage (in volts): ");
scanf("%f", &voltage);
printf("Enter the current (in amperes): ");
scanf("%f", ¤t);
// Calculate resistance using Ohm's law (V = IR)
resistance = voltage / current;
// Output the calculated resistance
printf("The value of resistance is: %.2f ohms\n", resistance);
return 0;
}
```
In this program, the user is prompted to enter the voltage and current values. The program then calculates the resistance using Ohm's law (V = IR) and outputs the result. Make sure to compile and run the program to test it with different voltage and current values.
Learn more about resistance here:
https://brainly.com/question/30113353
#SPJ11
What would be the value of the prescaler of the Watchdog timer of the ATMEGA device so that it will reset the CPU if it is not restarted in 4 s?
Show the bit settings in the Watch Dog Timer Control Register WDTSCR for the above prescale value (The other non-prescale related bits may be zero).
The AT mega device's watchdog timer pre-scaler value for resetting the CPU after 4 seconds would be 1024. The bit settings in the Watchdog Timer Control Register (WDTSCR) for this prescale value are as follows:
The AT Mega's watchdog timer is an essential feature that allows the system to recover if a software error occurs. The watchdog timer must be periodically restarted by software to avoid causing a system reset. If the system fails to restart the timer, it will cause a system reset. The watchdog timer can be used to recover from software errors that cause the system to stop responding.
To set the pre-scaler value for the Watchdog Timer Control Register (WDTSCR), follow these steps:
1. Choose a pre-scaler value. In this case, the pre-scaler value is 1024.
2. Find the corresponding bit settings for the pre-scaler value in the datasheet. According to the datasheet, the bit setting for a pre-scaler value of 1024 is "101" (i.e., bit 0 is high, bit 1 is low, and bit 2 is high).
3. Set the corresponding bits in the WDTSCR register. For a pre-scaler value of 1024, the WDTSCR value would be 0b00001000. The other non-prescale related bits can be zero.
To know more about software error refer to:
https://brainly.com/question/24254789
#SPJ11
Design an instrumentation Amplifier circuit by using three
operational amplifiers on Breadboard. Kindly make neat and clean
connections for better understanding.
An instrumentation amplifier circuit can be created by using three operational amplifiers on a breadboard.
The purpose of an instrumentation amplifier is to amplify very small signals accurately. It is mainly used for measuring bioelectric signals, strain gauges, and thermocouples. The following are the steps to create an instrumentation amplifier circuit using three operational amplifiers on a breadboard:
Step 1: Choose three operational amplifiers like LM741.
Step 2: Connect pin 4 and pin 7 of the LM741 to the positive and negative power supply respectively.
Step 3: Connect the output of the first LM741 to the inverting input of the second LM741.
Step 4: Connect the non-inverting input of the first LM741 to the signal source.
To know more about instrumentation visit:
https://brainly.com/question/28572307
#SPJ11
Consider the following grammar: E → (L) la L-L, EE a. Construct the DFA of LR(1) items for this grammar. b. Construct the general LR(1) parsing table. c. Construct the DFA of LALR(1) items for this grammar. d. Construct the LALR(1) parsing table.
a. DFA of LR(1) items for the given grammar:
Constructing the DFA of LR(1) items involves determining the sets of LR(1) items reachable from the start production. Each LR(1) item consists of a production rule with a dot indicating the current position in the rule, along with a lookahead symbol. Here is the DFA of LR(1) items for the given grammar:
b. General LR(1) parsing table:
To construct the general LR(1) parsing table, we need to determine the actions and state transitions for each item in the LR(1) items sets. The parsing table contains entries for each state and lookahead symbol combination. The entries can include shift actions, reduce actions, and go to transitions. Due to the complexity and size of the parsing table, I'm unable to provide it here directly.
c. DFA of LALR(1) items for the given grammar:
Constructing the DFA of LALR(1) items involves merging compatible LR(1) items sets from the LR(1) items DFA. The merged sets retain the same LR(1) items but may have different state numbers. Here is the DFA of LALR(1) items for the given grammar:
d. LALR(1) parsing table:
To construct the LALR(1) parsing table, we use the merged sets of LR(1) items from the LALR(1) items DFA. The LALR(1) parsing table is similar to the general LR(1) parsing table but may have fewer states due to the merging process. Unfortunately, I cannot provide the full LALR(1) parsing table here due to its size and complexity.
Learn more about DFA of LR(1) here
brainly.com/question/33168210
#SPJ11
A system is linear if it has:
Scaling and additivity Stability and continuity Additivity and multiplicity Inputs and outputs
A system is linear if it has Scaling and additivity. A system in which the property of additivity and scaling are preserved is known as a linear system.
If the input to the system is scaled by a factor α, the output of the system will be scaled by the same factor α, in this case, additivity and scaling property are preserved. The general condition for a linear system is that it follows two axioms i.e. additivity and scaling property. In simple words, if a linear system is given an input x[n], the output signal would always be y[n], as follows: y(n) = ax1[n] + bx2[n]ax[n] + by[n]where x1[n] and x2[n] are the input signal, a and b are any scalar value and y[n] is the output signal. Hence, the system is linear if it follows the above property. Additionally, the scaling property ensures that the output signal is of the same form as the input signal and only a scaled version of it. Hence, a linear system can be characterized by two properties: scalability and additivity. The system is linear if it satisfies these conditions for every input and output signal. The stability and continuity of a system are not related to the linearity of a system. Therefore, options (b), (c), and (d) are incorrect options to choose from. Hence, the correct option is A) Additivity and scaling.
Learn more about Scaling Visit Here,
brainly.com/question/27117291
#SPJ11
Consider a one compartment (plasma) model for a drug that is administered with dose D at t = 0 and later a booster of dose D/2 at t = 6. Let the clearance rate k = 1/5 and x(t) be the amount of drug at time t.
(a) Set up a differential equation for x(t) with the proper initial condition. You should use the Dirac delta function in your model.
(b) Solve the ODE using Laplace transform.
(c) Make a rough hand sketch of x(t).
The sketch would depict a rising curve at the start, followed by a gradually declining curve with a bump at t = 6 due to the booster dose. The specific shape and characteristics of x(t) would depend on the values of D, k, and the duration of the observation period. The initial condition is x(0) = 0, assuming no drug is present in the plasma compartment initially.
(a) To set up the differential equation for x(t), we consider the one-compartment (plasma) model and incorporate the administration of the drug at t = 0 and the booster at t = 6. Let's denote the clearance rate as k = 1/5.
The differential equation for x(t) can be expressed as:
dx/dt = -kx(t) + D * δ(t) + (D/2) * δ(t-6)
Here, the first term on the right-hand side (-kx(t)) represents the clearance of the drug from the plasma compartment, where k is the clearance rate and x(t) is the amount of drug at time t. The second term (D * δ(t)) represents the initial dose administered at t = 0 using the Dirac delta function δ(t), which accounts for an instantaneous increase in drug concentration. The third term ((D/2) * δ(t-6)) represents the booster dose administered at t = 6.
The initial condition is x(0) = 0, assuming no drug is present in the plasma compartment initially.
(b) To solve the ODE using Laplace transform, we can take the Laplace transform of both sides of the differential equation and then solve for X(s), where X(s) is the Laplace transform of x(t). The Laplace transform of x(t) is denoted as X(s) = L{x(t)}.
The Laplace transform of dx/dt is sX(s) - x(0), and the Laplace transform of δ(t) is 1. Applying these transforms to the differential equation, we have:
sX(s) - x(0) = -kX(s) + D + (D/2) * e^(-6s)
Rearranging the equation and substituting the initial condition x(0) = 0, we get:
(s + k)X(s) = D + (D/2) * e^(-6s)
Solving for X(s), we have:
X(s) = (D + (D/2) * e^(-6s)) / (s + k)
To obtain x(t), we need to find the inverse Laplace transform of X(s).
(c) A rough hand sketch of x(t) would depend on the specific values of D and k. However, in general, we can expect x(t) to initially increase rapidly after the initial dose is administered at t = 0. Then, over time, it will gradually decrease due to the clearance rate k. At t = 6, when the booster dose is administered, x(t) will experience a temporary increase before continuing its gradual decrease.
The sketch would depict a rising curve at the start, followed by a gradually declining curve with a bump at t = 6 due to the booster dose. The specific shape and characteristics of x(t) would depend on the values of D, k, and the duration of the observation period.
Learn more about curve here
https://brainly.com/question/33104408
#SPJ11
20 kW, 250V, 1000 rpm shunt excited DC motor hos armature ond field resistances of 0,22 and 240. When the motor tales 110 A rated current of ro ted conditions:
a) The roted input power, rated output power, and efficiency. 6) Generated voltage of 1200 rpm. c) Induced torque. d) The total resistance to limit the storting current to 1,2 times the full lood current.
To provide accurate calculations, please provide the missing information such as the armature resistance, field resistance, back EMF constant, and full load current.
What information is needed to calculate the rated input power, rated output power, efficiency, generated voltage at 1200 rpm, induced torque, and total resistance for the given shunt excited DC motor?a) The rated input power can be calculated using the formula:
Input power (P_in) = Rated current (I_rated) * Rated voltage (V_rated)
P_in = 110 A * 250 V
The rated output power (P_out) is equal to the mechanical power developed by the motor, which can be calculated as:
P_out = Rated current (I_rated) * Rated voltage (V_rated) * Efficiency
To determine the efficiency, we need additional information such as the armature resistance and field resistance, as well as the no-load current and voltage.
b) To calculate the generated voltage at 1200 rpm, we need information about the motor's speed and its back EMF constant (K_E).
c) The induced torque can be calculated using the formula:
Torque (T) = K_E * Armature current (I_a)
d) To limit the starting current to 1.2 times the full load current, we need to calculate the total resistance (R_total). This requires information about the armature resistance and field resistance, as well as the full load current (I_rated).
Learn more about resistance
brainly.com/question/32301085
#SPJ11
Solve aasap dont spam solve completely all if you can't just leave don't waste my post upvote for good work tq asap. 2) A balanced three phase power system is supplied by 4. 12-15 kV, carrying four parallel 3-phase-loads, as follows: Load 1: 515 kVA with 0.79 power factor, Capacitive with 0.83 Leading power factor Load 2: 320 kVAR Load 3: 170 kW with 0.91 Lagging power factor Load 4: is a A connected load of 90 -j 35 22 per phase Find the line current for each load and then, the total line current if the first three loads are Y connected, and then, repeat that, when these loads are A connected.
The line current for each load and the total line current in a balanced three-phase power system are as follows:
Load 1: Line current = 331.32 A
Load 2: Line current = 204.07 A
Load 3: Line current = 181.07 A
Load 4: Line current = 59.79 A
Total line current (Y connected): 777.46 A
Total line current (A connected): 450.48 A
In a balanced three-phase power system, the line current for each load can be calculated using the formula:
Line current = Apparent power / (√3 × line voltage × power factor)
Load 1 is specified in terms of apparent power and power factor. By substituting the given values into the formula, we can determine the line current for Load 1 as 331.32 A.
Load 2 is given in terms of reactive power (kVAR), which represents the power consumed or generated by the load due to inductance or capacitance. Since the power factor is not provided, we assume it to be 1 (unity power factor). By converting the reactive power to apparent power (kVA) and using the formula, the line current for Load 2 is found to be 204.07 A.
is provided in terms of real power (kW) and power factor. By substituting the values into the formula, the line current for Load 3 is calculated as 181.07 A.
is represented as an impedance in complex form. To find the line current, we first need to convert the impedance to its equivalent in rectangular form.
Using the formula Z = R + jX, where R represents the resistance and X represents the reactance, we can calculate the equivalent impedance as (90 - j35) Ω per phase. Then, by applying Ohm's law (I = V/Z), where V is the line voltage and Z is the impedance, we determine the line current for Load 4 as 59.79 A.
To find the total line current when Loads 1, 2, and 3 are Y connected, we add the individual line currents. The total line current is 777.46 A.
When the loads are A connected, we divide the total line current by √3 to account for the phase shift. Therefore, the total line current in the A connection is 450.48 A.
Learn more about Balanced
brainly.com/question/31237748
#SPJ11
2) Write an array of adj2, adj3, and adj4.
It's a C language assignment.
Here's an example of how you can declare an array of `adj2`, `adj3`, and `adj4` in the C language:
```c
#include <stdio.h>
int main() {
int adj2[5]; // Array of adj2 with size 5
float adj3[3]; // Array of adj3 with size 3
char adj4[8]; // Array of adj4 with size 8
// Accessing and modifying array elements
adj2[0] = 10;
adj2[1] = 20;
adj2[2] = 30;
adj2[3] = 40;
adj2[4] = 50;
adj3[0] = 3.14;
adj3[1] = 2.718;
adj3[2] = 1.618;
adj4[0] = 'H';
adj4[1] = 'e';
adj4[2] = 'l';
adj4[3] = 'l';
adj4[4] = 'o';
adj4[5] = ' ';
adj4[6] = 'W';
adj4[7] = 'o';
adj4[8] = 'r';
adj4[9] = 'l';
adj4[10] = 'd';
// Printing array elements
printf("adj2: ");
for (int i = 0; i < 5; i++) {
printf("%d ", adj2[i]);
}
printf("\n");
printf("adj3: ");
for (int i = 0; i < 3; i++) {
printf("%.3f ", adj3[i]);
}
printf("\n");
printf("adj4: ");
for (int i = 0; i < 11; i++) {
printf("%c", adj4[i]);
}
printf("\n");
return 0;
}
```
In this example, `adj2` is an array of integers with a size of 5, `adj3` is an array of floats with a size of 3, and `adj4` is an array of characters with a size of 8. You can access and modify individual elements of the arrays using the index notation (`arrayName[index]`).
The code also demonstrates how to print the elements of each array using loops. In the case of `adj4`, which is an array of characters representing a string, we print each character until the null-terminating character (`'\0'`) is encountered.
You can compile and run this C program to see the output that displays the elements of `adj2`, `adj3`, and `adj4`.
Learn more about C language here:
https://brainly.com/question/31360599?
#SPJ11
A ring core made of mild steel has a radius of 50 cm and a cross-sectional area of 20 mm x 20 mm. A current of 0.5. A flows in a coil wound uniformly around the ring and the flux produced is 0.1 mWb. If the reluctance of the mild steel, S is given as 3.14 x 107 A-t/Wb, find (i) The relative permeability of the steel. (ii) The number of turns on the coil.
A ring core made of mild steel has a radius of 50 cm and a cross-sectional area of 20 mm x 20 mm. A current of 0.5. A flows in a coil wound uniformly around the ring and the flux produced is 0.1 m Wb. If the reluctance of the mild steel, S is given as 3.14 x 107 A-t/Wb,
find (i) The relative permeability of the steel. (ii) The number of turns on the coil.(i) The relative permeability of the steel. The magnetic field inside the ring core can be calculated as below: B = µH Where B is the magnetic flux density, H is the magnetic field intensity, and µ is the permeability of the medium. The magnetic field intensity inside the ring core can be calculated as below: H = (Ni) / (l)Where N is the number of turns on the coil, i is the current flowing in the coil, and l is the average path length of the magnetic circuit.
To know more about magnetic circuit visit:
brainly.com/question/31605194
#SPJ11
with this keys
AHB ,CHI, DCR
please answer with the step and the keys that given. for the following sequence of keys, do the following:
MBX, EXB, GBX,..., ABX, AXB,..., QXB, YXB,....
1. Fill in the 3 blanks with strings from your first, second, and third name.
2. Build an AVL tree showing all steps in details.
3. Build a max- Heap showing all steps in details.
To complete the tasks using the given keys (AHB, CHI, DCR) and the provided sequence of keys, follow the steps below:
1. Fill in the blanks with strings from your first, second, and third name:
- MBX, EXB, GBX, AHB, AXB, CHI, DCR, QXB, YXB
2. Build an AVL tree showing all steps in detail:
- Start with an empty AVL tree.
- Insert the keys in the following order:
- MBX
- EXB
- GBX
- AHB
- AXB
- CHI
- DCR
- QXB
- YXB
The AVL tree after each insertion step will be as follows:
CHI
/ \
AHB EXB
/ \ / \
AXB GBX DCR QXB
\
MBX
\
YXB
3. Build a max-Heap showing all steps in detail:
- Start with an empty max-Heap.
- Insert the keys in the following order:
- MBX
- EXB
- GBX
- AHB
- AXB
- CHI
- DCR
- QXB
- YXB
The max-Heap after each insertion step will be as follows:
YXB
/ \
QXB DCR
/ \ / \
MBX AXB CHI EXB
\
GBX
Learn more about max-Heap here:
https://brainly.com/question/30154180
#SPJ11
A three phase motor draws a line curent of 30 A when supplied from a 450 V three phase 25 Hz source. The motor efficiency and power factor are 90% and 75%, respectively. Determine the total input reactive power for the motor.
The motor efficiency and power factor are 90% and 75%, respectively, then the total input reactive power for the motor is 14.63 kVAR.
From the question above, dataLine current drawn by the 3-phase motor (I) = 30 A
Voltage supplied to the 3-phase motor (V) = 450 V
Frequency of supply (f) = 25 Hz
Motor efficiency (η) = 90% = 0.9
Power factor (PF) = 75% = 0.75
Calculating the input apparent power of the motor, we have:S = √3 VI …(1)
Here, √3 = 1.732, so we have:
S = 1.732 × 450 × 30S = 23.18 kVA …(2)
Since power factor is given by the ratio of active power to apparent power, we can calculate the active power as follows:
Active Power = P = S × PF …(3)
So, P = 23.18 × 0.75P = 17.39 kW …(4)
Now, the reactive power can be calculated using the following formula:
Reactive Power = Q = S² sin θ …(5)
where θ is the angle between the voltage and the current phasors.
Q = 23.18² sin cos⁻¹(0.75)Q = 14.63 kVAR
Therefore, the total input reactive power for the motor is 14.63 kVAR.
Learn more about reactive power at
https://brainly.com/question/30685063
#SPJ11
A boiler produces 6 tonnes/hour of steam at a pressure of 1.8 MPa and a temperature of 250ºC. Feedwater enters at a temperature of 39ºC. At exit from the economizer part of the boiler the temperature is 72ºC. At exit from the evaporator part of the boiler the steam is 90 % dry. Energy is supplied by 650 kg of coal per hour, which has a calorific value of 36 MJ/kg. The A/F ratio is 25 : 1. The temperature of the flue gas at entry to the economizer part of the boiler is 430ºC. The average specific heat at constant pressure of the flue gas in the economizer is 1045 J/kg.K. 4.1 Calculate the efficiency of the boiler. [70.5 %] 4.2 Draw up an energy balance, on a kJ/kg coal basis, with percentages of the total energy supplied. [economizer 3.6 %, evaporator 59 %, superheater 8 %, other 29.4 %
Efficiency of the boiler: To determine the efficiency of the boiler, use the equation, η = ((heat energy produced by the steam)/(energy supplied by fuel)) × 100%
Calculation of heat energy produced by the steam, Qs
Qs = ms×Hfgh × (1 - x)
Given, the steam produced is 90% dry.
x = 0.1
Specific enthalpy at a pressure of 1.8 MPa and a temperature of 250ºC,
hfg = 2595.3 kJ/kg
Specific enthalpy of dry saturated steam at a pressure of 1.8 MPa,
hfs = 2885.3 kJ/kg
hfgh = hfg - hfs= 2595.3 - 2885.3= - 290 kJ/kg
The flow rate of steam produced,
ms = 6 tonnes/hour = 6000 kg/hour
Qs = ms ×hfgh × (1 - x)= 6000 × (- 290) × (1 - 0.1)= - 1,610,000 kJ/hour
\Calculation of energy supplied by fuel Energy supplied by fuel,
Qf= M f ×C V
Where
Mf = 650 kg/hour (mass of coal burnt per hour)
CV = 36 MJ/kg (calorific value of coal)
Q f= 650 × 36 × 1000= 23,400,000 J/hour = 23,400,000/3600 = 6500 kW
the energy balance, on a kJ/kg coal basis, with percentages of the total energy supplied is given by,
Economizer 3.6 %Evaporator 59 %Superheater 8 %Other 29.4 %
To know more about determine visit:
https://brainly.com/question/29898039
#SPJ11
Required information A three-phase line has an impedance of 1 + 32 per phase. The line feeds a balanced delta-connected load, which absorbs a total complex power of 12 + j5 kVA. The line voltage at the load end has a magnitude of 300 V. Calculate the magnitude of the line voltage at the source end. The magnitude of the line voltage at the source end is [ 304.6 V.
The magnitude of the line voltage at the source end is 304.6 V.
To calculate the magnitude of the line voltage at the source end, we need to consider the impedance of the three-phase line and the complex power absorbed by the balanced delta-connected load.
Given that the impedance per phase of the line is 1 + 32, we can calculate the total line impedance (Z) by multiplying it by the square root of 3. Therefore, Z = (1 + 32) * √3 ≈ 55.36.
Since the load is balanced and delta-connected, the line current (I) can be calculated using the formula: I = S / (√3 * V), where S is the complex power and V is the line voltage magnitude at the load end. In this case, I = (12 + j5) kVA / (√3 * 300 V) ≈ 0.0401 + j0.0167 kA.
To determine the line voltage at the source end (Vs), we can use Ohm's law: Vs = Vload + I * Z, where Vload is the line voltage magnitude at the load end. Plugging in the values, Vs = 300 V + (0.0401 + j0.0167 kA) * 55.36 ≈ 304.6 V.
Therefore, the magnitude of the line voltage at the source end is approximately 304.6 V.
Learn more about line voltage
brainly.com/question/29445057
#SPJ11
Draw the three-dimensional radiation pattern for the Hertz antenna, and explain how it is developed
The Hertz antenna, also known as a half-wave dipole antenna, is one of the oldest and most widely used antennas. A half-wave dipole antenna is used to broadcast and receive radio signals and is made up of two identical conductive rods separated by an insulator.
The antenna has two lobes, one in the vertical plane and the other in the horizontal plane. The horizontal lobe is perpendicular to the axis of the antenna, while the vertical lobe is parallel to the axis. The radiation pattern of a dipole antenna is more directional than an omnidirectional antenna. The three-dimensional radiation pattern of a dipole antenna depends on the length and diameter of the antenna.
The three-dimensional radiation pattern of a dipole antenna is a function of the frequency of the signal, the size of the antenna, and the distance between the antenna and the receiving station. The radiation pattern is affected by the length and diameter of the antenna and the distance between the antenna and the receiving station. The radiation pattern of a dipole antenna is not uniform, and the strength of the signal received varies depending on the angle of reception.
To know more about broadcast visit:
brainly.com/question/28896029
#SPJ11
A MIPS processor has a 32-bit address bus and a cache memory of 4K(212) words. The cache is 2-way set associative with a block size of 1 memory word. Here, each word is 32-bit long. (a) What bits of the address are used to select the set within the cache? (b) How many bits are in each tag, and (c) What is the actual size of the cache. (d) Repeat part (c) if cache uses direct mapping (1-way set associative) with a block size of 4 words.
a) A total of 32 bits is used to represent the address, and since the lower 11 bits are used to select the set within the cache. b) The tag is made up of the upper 21 bits of the address. c) Size of the cache is 16,384 bytes. d) For direct mapping, size of the cache is 4,096 bytes.
(a) To select the set within the cache, the lower 11 bits of the address are used.
The given cache has a size of 4K (212) words, it is two-way set-associative, and has a block size of one memory word.
As a result, there are a total of 4K / 2 = 2K sets in the cache.
Each memory word is 32 bits long, hence the address is 32 bits long (since there is a 32-bit address bus). A total of 32 bits is used to represent the address, and since the lower 11 bits are used to select the set within the cache, the remaining bits must be used for the tag.
(b) For the tag, the upper 21 bits are used since there are 11 bits to select the set within the cache.
The size of the tag is determined by the number of bits that are left over after the bits used to select the set have been subtracted from the total number of bits used to represent the address.
As a result, the tag is made up of the upper 21 bits of the address.
(c) The actual size of the cache is calculated as follows:
Size of each block = 1 word = 4 bytes
Size of each set = (Block size) × (Number of blocks per set)= 1 word × 2 = 2 words = 8 bytes
Number of sets = (Cache size) / (Set size)= (4K words) / (2 sets) = 2K sets
Size of the cache = (Set size) × (Number of sets)= (8 bytes/set) × (2K sets)= 16K bytes= 16 × 1024 = 16,384 bytes.
(d) If the cache is implemented using direct mapping (1-way set associative), there will be only one block per set. As a result, the number of sets is equal to the total number of blocks.
The number of blocks is calculated by dividing the size of the cache by the size of each block.
Number of blocks = (Cache size) / (Block size)= (4K words) / (4 words/block) = 1K blocks.
Number of sets = Number of blocks = 1K sets.
Size of the cache = (Set size) × (Number of sets)= (4 bytes/set) × (1K sets) = 4K bytes= 4 × 1024 = 4,096 bytes.
Learn more about cache here:
https://brainly.com/question/23708299
#SPJ11
Problem 5: Suppose, A 741 OP-AMP is used in an electronic circuit. a) If the rise time is 5 sec, compute the unity gain bandwidth. b) Maximum 15µA current required to compensate 30pF capacitor. Compute the slew rate of 741 IC. c) Compute the maximum frequency to get undistorted sine wave output voltage of 15V (peak)
The maximum frequency for undistorted sine wave output from the 741 op-amp at a peak voltage of 15 V is approximately 5.3 kHz.
How to solve for the maximum frequencyUnity gain = 0.35 / 5 seconds of rise time
Unity gain = 0.07
The Maximum 15µA current
= 15µA / 30
= 0.5 v / s
SR = 15 * 10^-6 / 30 * 10^-12
= 0.5 V/µs
The maximum frequency = 0.5 / 2 * π * 15
= 5.307
This means that the maximum frequency for undistorted sine wave output from the 741 op-amp at a peak voltage of 15 V is approximately 5.3 kHz.
Read mroe on maximum frequency here https://brainly.com/question/30906396
#SPJ1
Problem 2: A balanced Δ-connected load having an impedance 20-j15 Ω is connected to a Δ-connected, positive-sequence generator having V
ab
=330/0
∘
V. Calculate the phase currents of the load and the line currents.
The impedance of the load, Z = 20 - j15 ΩThe line voltage, Vab = 330/0o VWe know that the phase voltage, Vph = V line/sqrt(3)Vph = (330/0) / sqrt(3) = 190.56∠0o volts.
The load is balanced delta-connected, which means the impedance of each phase will be the same. The delta-connected load will look like the below circuit:Impedance of each phase, Zph = Z/ZIph = Vph/ZphIph = 190.56∠0o / (20 - j15)Iph = 6.89∠39.8o
AmpsThe line current, Iline = √3IphIline = √3 * 6.89∠39.8oIline = 11.94∠39.8o AmpsPhase currents of the load will be equal to the phase currents in the delta-connected circuit, thus;Ia = 6.89∠39.8o A, Ib = 6.89∠-80.2o A and Ic = 6.89∠+100.2o A.
To know more about impedance visit :-
https://brainly.com/question/30475674
#SPJ11
Design a circuit, using op amps that will output the following equation: Vo= (3V1 +5V2 + 7V3)
In order to design the circuit using op amps to output the equation
Vo= (3V1 +5V2 + 7V3),
we will need to use summing amplifier configuration. This configuration is also known as the inverting summing amplifier. This circuit is a type of operational amplifier circuit configuration that is used to combine the multiple inputs using one inverting amplifier. The summing amplifier configuration will allow us to sum the three voltages V1, V2, and V3, with different weightage given to each of them. The weightage will be as follows: V1 will have a weight of 3, V2 will have a weight of 5 and V3 will have a weight of 7. The output voltage (Vo) of the summing amplifier using op amps is calculated using the equation
:Vo= −(Rf/R1) [(V1/R1) + (V2/R2) + (V3/R3)]
Where,Rf is the feedback resistorR1, R2, and R3 are the input resistorsV1, V2, and V3 are the input voltagesThe above equation will sum all the input voltages and apply the respective weightage to each voltage. Using the summing amplifier configuration, we can easily output the required equation,
Vo= (3V1 +5V2 + 7V3), by setting the values of the input resistors and the feedback resistor. This can be easily done by using the values of
R1 = R2 = R3
Rf = 1.6R1.
Therefore, the above equation can be re-written as follows:
Vo= − (1.6) [(V1/R) + (V2/R) + (V3/R)]Where
,R1 = R2 =
R3 = R=
Vo = Output voltage
To know more about circuit visit:
https://brainly.com/question/32231314
#SPJ11
A product requires 20 dB of shielding at 200 MHz. It is planned to use 100 small round cooling holes (all the same size) arranged in a 10 by 10. array. What is the maximum diameter for one of the holes?
The maximum diameter for one of the holes is 26 mm.
In order to determine the maximum diameter for one of the holes in a product requiring 20 dB of shielding at 200 MHz using 100 small round cooling holes (all the same size) arranged in a 10 by 10 array, we will use the formula for shielding effectiveness (SE) for a conductive enclosure:
SE = 20 log₁₀(Vi / Vt)
where SE is shielding effectiveness in decibels, Vi is the voltage incident on the enclosure, and Vt is the voltage transmitted through the enclosure. We can re-arrange this formula to solve for Vi / Vt:
Vi / Vt = 10^(SE / 20)
We know that SE = 20 dB and f = 200 MHz. We can also assume that the enclosure is well-sealed except for the 100 small round cooling holes arranged in a 10 by 10 array. Therefore, we can model the enclosure as a rectangular box with dimensions of 1 m x 1 m x 1 m, and assume that the incident voltage is equal to the free-space incident field.
Vi / Vt = 10^(SE / 20) = 10^(20 / 20) = 10
The ratio of the incident voltage Vi to the transmitted voltage Vt is 10.
Since the incident voltage is equal to the free-space incident field, which is given by: Ei = Eo / r where Eo is the electric field strength at a distance of 1 m from the source, and r is the distance from the source, we can write:
Ei = Eo / r = 1 V/m / (4π(200 MHz)(1 m)) = 1.99 × 10⁻⁹ V/m
Therefore, the transmitted voltage Vt is given by:
Vt = Vi / 10 = 1.99 × 10⁻¹⁰ V/m
The maximum diameter for one of the holes is given by the equation for shielding effectiveness in terms of hole diameter:
d = 4.96λ / (1 + SE)
where d is the hole diameter in meters, λ is the wavelength in meters, and SE is the shielding effectiveness in decibels.λ = c / f where c is the speed of light in meters per second.λ = c / f = 3 × 10⁸ m/s / (200 × 10⁶ Hz) = 1.5 m Therefore, the maximum diameter for one of the holes is:
d = 4.96λ / (1 + SE) = 4.96(1.5) / (1 + 20) = 0.026 m = 26 mm.
To know more about shielding refer for :
https://brainly.com/question/31037411
#SPJ11
