If you increase either mass or velocity, the momentum of the object increases proportionally. If you double the mass or velocity you double the momentum.
what is momentum?
As momentum depends on both velocity and the direction of the body's motion, it is quantified by "mass velocity". Since velocity is a vector and mass is a scalar, momentum is a vector quantity. Mass times speed equals momentum.
"The motion of an item equal to the product of its mass and its velocity" is referred to as momentum. When something is said to have momentum, it refers to its unique mass and direction of motion.
To learn more about mass or velocity, visit:https://brainly.com/question/2548537
#SPJ4
The switch in the circuit in (Figure 1) has been in the left position for a long time. At t- 0, it moves to the right position and stays there. Figure 1 of 1 sov 150 V+ 40 nF 30k60 k2 a) Find the initial voltage drop across the capacitor. b) Find the initial energy stored by the capacitor. c) Find the time constant of this circuit for t>0. d) Write the expression for the capacitor voltage v(t) for t 20. Express your answer in terms of t, where t is in seconds.
The initial voltage drop across the capacitor is 150v,b) The initial energy stored by the capacitor is 450 × [tex]10^{-6}[/tex]
Figure 1 of 1 150 V drop given ,So across the capacitor is 150v
initial energy stored by the capacitor = 1/2 CVc(v)
energy = 1/2 × 40 × [tex]10^{-9}[/tex] × 150×150
= 450 × [tex]10^{-6}[/tex]
the expression for the capacitor voltage v(t) for t 20 is
Vc(t) = Vc(α) + [Vc(0) - Vc(α)][tex]e^{t/T}[/tex]
By building up electric charges on two nearby surfaces that are isolated from one another, a capacitor is a device that stores electrical energy in an electric field. It is a two-terminal passive electrical component.
Capacitance is the name given to a capacitor's effect. While there is some capacitance between any two electrical conductors that are close to one another in a circuit, a capacitor is a component made to increase capacitance in a circuit. Condenser is a term that still appears in a few compound names for the capacitor, such as condenser microphone.
Practical capacitors come in many different shapes and sizes, and they are made of a large variety of materials. Most capacitors include two or more electrical conductors, frequently in the form of metallic plates.
Learn more about capacitor here:
https://brainly.com/question/17176550
#SPJ4
The reaction that converts a saturated dicarboxylic acid into an unsaturated one
Spell out the full name of the enzyme.
The reaction that converts a saturated carboxylic acid into an unsaturated one is the succinate dehydrogenase enzyme.
What is acid?Any material that tastes sour when dissolved in water is an acid. It also alters the color of some indicators (such as reddening blue litmus paper), reacts with some metals (such as iron) to release hydrogen, combines with bases to create salts, and facilitates a number of chemical activities (acid catalysis).
Sulfuric, nitric, hydrochloric, and phosphoric acids, as well as organic chemicals, belong to the carboxylic acid, ammonium sulfate, and phenol groups, are examples of acids.
Acids are also inorganic entities known as alkaline solutions. These chemicals have one or more hydrogen atoms, which are discharged as positively charged ions in solution.
The full name of the enzyme is succinate dehydrogenase enzyme.
To know more about Acid:
https://brainly.com/question/14072179
#SPJ1
Which one of the following temperatures is equal to 5 degrees Celsius? 41k, 278k, 0k, 465k
Answer:
5°C is equal to 278 K.
Explanation:
0 degrees Celsius is equal to 273.15 Kelvins. The basic formula is °C + 273.15 = K. Kelvin to Celsius: Add 273.
In a period of 1.00 s, 5.00×1023 nitrogen molecules strike a wall with an area of 8.00cm2. Assume the molecules move with a speed of 300 m/s and strike the wall head-on in elastic collisions. What is the pressure exerted on the wall? Note: The mass of one N2 molecule is 4.65×10−26kg.
A wall with an area of 8 cm² is struck by 5.00 x 10²³ nitrogen molecules over the course of 1 s. Assume that the molecules are moving at a speed of 300 m/s and colliding with the wall in an elastic manner. The pressure acting on the wall is 17.43 kPa.
Mass in motion is a definition of momentum. Mass and velocity are multiplied to determine momentum. That is, p = mv where p,m, and v denotes momentum, mass, and velocity.
Given the change in the time period, Δt is 1 second, the number of nitrogen molecules is 5.00×10²³ molecules, the change in velocity Δv is 300 m/s, and the area is 8×10⁻⁴ m².
The momentum of one molecule is given as 2mΔv. Then, the momentum of N molecules is 2NmΔv.
The force exerted on the wall by nitrogen molecule is written as,
[tex]\begin{aligned}\text{Force F}&=\frac{\Delta\text {momentum}}{\Delta t}\\&=\frac{2Nm\Delta v}{\Delta t}\end{aligned}[/tex]
Then, the pressure exerted by nitrogen molecule on the wall is,
[tex]\begin{aligned}P&=\frac{F}{A}\\&=\frac{2Nm\Delta v}{\Delta t\times A}\\&=\frac{2\times 5\times10^{23}\times4.65\times10^{-26}\times300}{8\times 10^{-4}\times 1.00}\\&=\mathrm{17.43\;kPa}\end{aligned}[/tex]
Therefore, the required answer is 17.43 kPa.
To know more about momentum:
https://brainly.com/question/29598011
#SPJ4
The blue-ringed octopus reveals the bright blue rings that give it its name as a warning display (Figure 1). The rings have a stack of reflectin (a protein used for structural color in many cephalopods) plates with index of refraction n = 1.59 separated by cells with index n = 1.37. The plates have thickness 62 nm. What is the longest wavelength, in air, of light that will give constructive interference from opposite sides of the reflecting plates?
The wavelength of light in air that will give constructive interference from opposite sides of the reflecting plates is 394.32 nm.
When two waves travel in the same direction and are in phase with each other, their amplitudes get added and the resultant wave is obtained. Here, the waves are said to have undergone constructive interference. Upward displacement happens when the wave undergoes constructive interference. Hence, the upward displacement of the medium is greater than the displacement of the two interfering pulses.
Constructive interference occurs when the phase difference between the waves is an even multiple of π.
We know that the path difference is (2 * m t + λ/2)
So, for constructive interference,
(2 * m t + λ/2) = n λ
2 t = (m + 1/2)* λ/ n
For m = 0, λ = 4 t n
λ = 4 * (62* 10⁻⁹) * 1.59 = 394.32 * 10⁻⁹ m = 394.32 nm
To know more about constructive interference:
https://brainly.com/question/29767029
#SPJ4
(figure 1) shows five identical light bulbs a-e connected to a battery. initially, some of the bulbs light up because the two terminals of each bulb are connected to opposite terminals of the battery. if any wire in the circuit is cut, some bulbs may go out. figure1 of 1 part a part complete which bulbs, if any, go out when a single cut is made at location a? check all that apply. a b c d e none previous answers correct part b which bulbs, if any, go out when a single cut is made at location b? check all that apply. which bulbs, if any, go out when a single cut is made at location ?check all that apply. a b c d e none request answer part c which bulbs, if any, go out when a single cut is made at location c? check all that apply.
Figure shows five identical light bulbs a-e connected to a battery.
Part A: The potential at points 1 and 3 is different because of the internal resistance of B, so B is already glowing.
Part B: If a cut is made at point b, then no bulb will go out because C is already fused.
Part C: If a cut is made on C, then no bulb will go out because D and E were already fused.
What is the potential difference?When two places in a circuit contain different amounts of charge carriers' energy, this is referred to as a potential difference.
Part A:
Use the concept of potential difference to understand this question.
The bulb will only be lit when there is some potential difference. If the potential difference is zero, then the bulb will not light.
First, redraw the diagram and shown it below:
The potential at points 1 and 3 is different because of the internal resistance of B, so B is already glowing.
Part B
The potential at points 3 and 4 is the same because there is no resistance between them and the potential across C is 3 and 4. So, the potential difference is zero across C and it was already fused.
So, if a cut is made at point b, then no bulb will go out because C is already fused.
Part C
The potential at points 2, 4, 5, and 6 is the same. The potential across D and E is 5 and 6. The potential difference is zero across them, so they were already fused.
If a cut is made on C, then no bulb will go out because D and E were already fused.
To know more about battery refer to:
https://brainly.com/question/5059264
#SPJ1
The complete question is as follows:
Stanley Milgram Shock experiment participants gave intense electric shocks to strangers if they were asked to do so by the experimenter No shocks were actually delivered but the participants believed that they were delivering the shocks and kept shocking the stranger (who was really an actor seated in another room) as punishment for responding incorrectly to a word problem
The Milgram Experiment with Shock By Saul McLeod, 2017 update One of the most well-known experiments on obedience in psychology was conducted by Yale University psychologist Stanley Milgram.
He conducted an experiment that looked at the tension between following orders and one's conscience. Stanley Milgram, a social psychologist at Yale University, conducted the Milgram experiment (or experiments) on compliance to authoritative persons. November 5, 2018 revision. Stanley Milgram, a psychologist, investigated the ideas of submission and authority in a number of research in the 1960s. His studies comprised giving study participants orders to shock an actor in a different room with shocks of increasing voltage; the actor would scream at first and then go silent as the shocks grew stronger.
To learn more about Stanley Milgram please click on below link
https://brainly.com/question/10138784
#SPJ4
What is the speed of the wave if its wavelength is 3.0 m?; What is the wavelength of a wave with a speed of 12 m/s and a frequency of 3hz?; How do you find frequency when given wavelength and speed?; How do you find frequency of a wave?
The wavelength and speed of a wave are known, these can be used to find the frequency of a wave using the equation f=vλ f = v λ.
Wavelength can always be determined by measuring the distance between any two corresponding points on adjacent waves. In longitudinal waves, wavelength measurements are made by measuring the distance from one compression to the next or from one rarefaction to the next.
Forms of electromagnetic radiation such as radio waves, light waves, and infrared waves create characteristic patterns as they travel through space. Each wave has a specific shape and length. The distance between peaks is called the wavelength.
Wavelength is the distance between two wave crests and the same for wave troughs. Frequency is the number of oscillations that pass through a particular point in one second, measured in cycles per second this article discusses the relationship between wavelength and frequency.
Learn more about wavelength here:-https://brainly.com/question/29552794
#SPJ4
To derive the formulas for the major characteristics of motion as functions of time for a horizontal spring oscillator and to practice using the obtained formulas by answering some basic questions.
A block of mass m is attached to a spring whose spring constant is k. The other end of the spring is fixed so that when the spring is unstretched, the mass is located at x=0. . Assume that the +xdirection is to the right.
The mass is now pulled to the right a distance Abeyond the equilibrium position and released, at time t=0, with zero initial velocity.
Assume that the vertical forces acting on the block balance each other and that the tension of the spring is, in effect, the only force affecting the motion of the block. Therefore, the system will undergo simple harmonic motion. For such a system, the equation of motion is
a(t)=-\frac{k}{m}x(t),
and its solution, which provides the equation for x(t), is
At what time t_1 does the block come back to its original equilibrium position (x=0) for the first time?
Express your answer in terms of some or all of the variables: A, k, and m.
The system will undergo simple harmonic motion, so at time,
t₁ = π/2( [tex]\sqrt{k/m}[/tex])
What is simple harmonic motion?Simple harmonic motion is described as the periodic motion of a point along a straight line with an acceleration that is always toward a fixed point on that line and a distance from that point that is proportional to that acceleration.
The equation of motion for the simple harmonic oscillation of spring mass system is,
a(t) = -k/m x(t)
here, a(t) = is the acceleration at any time
k = is the spring constant, and
m = mass
The equation for displacement is given as,
x(t) = A cos ([tex]\sqrt{k/m}[/tex])t
here,
x(t) = is the displacement at any time.
A = is the amplitude of oscillations,
The velocity is given by,
v(t) = dx(t)/dt
The general expression of velocity for a simple harmonic motion is,
v(t) = v(max) sin ([tex]\sqrt{k/m}[/tex])t
v(max) = is the maximum velocity.
The kinetic energy is given as,
K(t) = 1/2 m[v(t)]²
Now, use the equation of position:
or, x(t) = A cos ([tex]\sqrt{k/m}[/tex])t
or, 0 = A cos ([tex]\sqrt{k/m}[/tex]) t₁
or, t₁ = π/2( [tex]\sqrt{k/m}[/tex])
Thus, the position of particle at time t₁ is 0. The cosine function is zero first time at angle π/2. The time can be calculated by substituting the values in the position function.
To know more about simple harmonic motion refer to:
https://brainly.com/question/20885248
#SPJ1
a mass m at the end of a spring oscillates with a frequency of 0.78 hz . when an additional 730 g mass is added to m, the frequency is 0.65 hz . What is the value of m?
The value of mass m = 0.506kg
Initial frequency = 0.78Hz
additional mass = 730 g = 0.73kg
New frequency = 0.65 Hz
F = 1/2π [tex]\sqrt{x\\}k/m[/tex]
0.78 = 1/2π [tex]\sqrt{k/m}[/tex]
additional mass,
0.65 = 1/2π [tex]\sqrt{k/m+0.65}[/tex]
1.44 = k/m / k/m+0.73
1.44 = m+0.73 / m
1.44m -m = 0.73
1.44m = 0.73
mass m = 0.506kg
a measurement used in physics to express the inertia, a quality that all matter has in common. Effectively, it is the resistance a body of matter offers to a change in its speed or position as a result of the application of a force. The change caused by an applied force is proportional to the mass of the body. The kilograms is the measure of mass in the International System of Units (SI). Its definition is based on the Planck constant, which is set at 6.62607015 1034 joule second. The unit of energy known as a joule is one kilogramme times one square metre per second. The kilogramme is determined by precise measurements of Planck's constant, while the second and metre are already defined in terms of other physical constants.
Learn more about mass here:
https://brainly.com/question/506625
#SPJ4
Consider a pendulum swinging. Which type(s) of energy is/are associated with the pendulum in the following instances: i. the moment at which it completes one cycle, just before it begins to fall back towards the other end, ii. the moment that it is in the middle between the two ends, iii. just before it reaches the end of one cycle (just before instant i.).
i. potential, ii. kinetic, iii. potential and kinetic
In the following situations, the type(s) the energy is/are related to the pendulum: potential kinetic potential,kinetic
When someone is kinetic, what does that mean?When an organism moves as a result of a stimulation like light, this is known as kinesis. Being able to use one's own internal kinesis power is what it means to be kinetic. Kinetics have such a supernatural ability, just like Telekinetics, Psychokinetics, and those who have Extra Sensory Perception.
What is it that makes kinetic energy move?Kinetic energy is the energy that any item has with a result of motion. An item can only be accelerated through the application of a force. Applying force requires effort on our part. Following completion of the work, energy is transmitted to the object, which then moves at the a new, consistent rate.
To know more about kinetic visit:
https://brainly.com/question/26472013
#SPJ4
Many satellites move in a circle in the Earth's equatorial plane. They are at such a height above the Earth's surface that they always remain above the same point. Such an orbit is said to be geosynchronous. Find the altitude of these satellites above the Earth's surface.
a) The altitude of these satellites above the Earth's surface is h = 3,588 10⁷ m , b) by the curve of the planet; consequently, the signals cannot reach these places
What is law of universal gravitation?
For this issue we must use the law of universal gravitation, with Newton's second law
F = m a
G m M / r² = m a (1)
Centripetal acceleration
a = v² / r
How the speed (speed) module is constant
v = d / t
Circle the distance in a complete orbit with a time (T) called period
d = 2π r
v = 2π r / T
a = (4π² r² / T²) / r
We substitute in equation 1
G M / r² = 4π² r / T²
G M / r³ = 4π² / T²
r = ∛ GM T² / 4π²
R is the distance from the center of the earth, the distance from the surface is
R = Re + h
Re + h = ∛ GM T²/ 4π²
h = ∛(G M T²/4π²) - Re
Let's reduce to SI units
T = 1 day (24h / 1 day) (3600s / 1h)
T = 86400 s
Let's calculate
h = ∛ (6.67 10⁻¹¹ 5.98 10²⁴ (8.6400 10⁴)² / 4π²) - 6.37 10⁶
h = ∛ (75.42 10²¹) - 6.37 10⁶
h = 4,225 10⁷ - 0.637 10⁷
h = 3,588 10⁷ m
b) In the attached you can see that for very large latitudes the linear path from the satellite to the earth is interrupted, by the curve of the planet; consequently, the signals cannot reach these places.
To learn more about Centripetal acceleration visit:https://brainly.com/question/14465119
#SPJ4
you now take three pieces of string from the previous problem and tie two of them together to make a string of double the mass density. you tie the single string and double string together and to two lamp posts that are 40 m apart as seen below. the interface is centered between the posts and the tension is 1.2 n. you briefly shake the string interface at 5 hz. By how many seconds does it win the race?
Taking three pieces of string from the previous problem and tie two of them together to make a string of double the mass density, V₁ = [tex]\sqrt{2}[/tex]V₂ it wins the race.
What is the mass density?An object's mass per unit volume is referred to as its mass density. The units that can be used to describe this characteristic are pounds per square foot (lb/ft²) and kilograms per square meter (kg/m³).
Given that,
tension = 1.2 N
Frequency = 5 Hz.
Length = 40 m
Let, mass density of thin string = m
mass density of thick string = 2m
As we know,
V₁ = [tex]\sqrt{F/m}[/tex]
V₂ = [tex]\sqrt{F/2m}[/tex]
Now,
V₁/V₂ = [tex]\sqrt{F/m} / \sqrt{F/2m}[/tex]
or, V₁/V₂ = [tex]\sqrt{2} /1[/tex]
or, V₁ = [tex]\sqrt{2}[/tex]V₂
Thus, speed of the thin string is [tex]\sqrt{2}[/tex] times greater than the speed of the thick string. So, it will comes first.
To know more about mass density refer to:
https://brainly.com/question/26364788
#SPJ1
A 20.0cm massless spring with spring constant 340N/m is suspended from the ceiling. A student carefully hangs a 450g mass from the free end. How long is the spring now?
After hanging the mass, the length of the spring is 21.3 cm using Hooke's law.
What is Hooke's law?According to the physics principle known as Hooke's Law, the force required to expand or compress a spring by a given distance is inversely proportional to that distance.
The first traditional example of an explanation of elasticity is Hooke's law. Elasticity is the quality of a substance or item that allows it to return to its original shape after distortion. A restoration force is a capacity to restore the original shape after experiencing distortion.
Given,
Equilibrium length of the massless spring = 20 cm
Spring constant k = 340 N/m
The spring is suspended from the ceiling.
Mass at the free end = 450 g
= 0.45 kg
A force is applied vertically downward on the spring due to the suspended mass which is equivalent to the weight of the mass i.e.
F = mg ... (1)
This force is balanced by the spring. If the spring is extended by a length of due to the suspension of the mass then by Hooke's law,
F = kx ... (2)
From equation (1) and (2)
mg = kx
x = mg/k
Put all the values
x = (0.45)(9.8)/(340)
= 0.013 m
= 1.3 cm
So, the length of the spring is
l = 20 + 1.3
= 21.3 cm
To know more about Hooke's law, visit:
https://brainly.com/question/29126957
#SPJ1
according to faraday's law, the induced emf is the rate of change of the magnetic flux through a closed loop..
According to Faraday's law, the magnetic flux through the loop's enclosed area changes at a rate that equals the induced emf around a closed loop.
The induced emf in a coil is equal to the rate of change of the flux linkage, as stated by Faraday's second law of electromagnetic induction. As a result, E = Ndϕdt.
It is no a conservative field, the induced electric field. You must exert effort when moving a charge once around the loop in opposition to the induced field. Your labor, however, is not kept as potential energy. To recoup the energy used to move the charge, you cannot allow the electric field to perform work. When the magnetic flux is no longer changing, the induced electric field also vanishes. There is no local storage for the work you perform on a charge against the induced field. An electromagnetic wave may be used to carry the energy away.
To learn more about magnetic flux click here https://brainly.com/question/24214683
#SPJ4
This one is a challenge
A motorcycle traveled north along a straight path for 2.22 hours with an average velocity of 67.8 km/h, stopped for 20.0 min, then traveled north for 3.33 hours with an average velocity of 77.7 km/h.
What is the average velocity for the trip?
What is the displacement for the entire trip?
Answer:
Explanation:
1 track section:
V₁ = 67.8 km/h
t₁ = 2.22 h
2nd track section:
V₂ = 0 km/h
t₂ = 20.0 min = (1/3) h ≈ 0.33 h
3 track section:
V₃ = 77.7 km/h
t₃ = 3.33 h
___________
V - ?
D - ?
Length of 1 track section:
D₁ = V₁·t₁ = 67.8·2.22 ≈ 150.5 km
Length 2 sections of track:
D₂ = V₂·t₂ = 0·0.33 = 0 km
Length 3 sections of track:
D₃ = V₃·t₃ = 77.7·3.33 ≈ 258.7 km
Summary path:
D = D₁ + D₂ + D₃ = 150.5 + 0 + 258.7 = 409.2 km
Total time:
t = t₁ + t₂ + t₃ = 2.22 + 0.33 + 3.33 = 5.88 h
Average speed:
V = D / t = 409.2 / 5.88 ≈ 69.6 km/h
Figure shows objects with charges. Show from which object the electrons flows. State why. In
which of these figures do you get a static electric spark? Draw the spark on the figure.
It is to be noted that the electron flows occur in Figures (a) and (d).
What is the rationale for the above answer?The total number of electrons in the left plate is equal to the total number of positive charges in the right plate in Figure (a). As a result, no electron flow occurs here. A static electric spark does not occur.
The left plate in Figure (b) has three negative charges and three positive charges. The right plate, on the other hand, has five negative charges and one positive charge. As a result of the neutralization effect, the plates now have additional negative charges. As a result of the extra electrons present, a static electric spark occurs.
The identical thing happens in Figure (c) as it does in Figure (b). As a result, an entire static electric spark happens here as well. The complete negative charges on the right plate are flowing toward the ground in Figure (d). As a result, the left side plate has total negative charges while the right side plate has total positive charges.
As a result, we can see that the electrons flow in Figures (a) and (d). While figures (b) and (c) show static electric sparks.
Learn more about Electron Flow:
https://brainly.com/question/17642965
#SPJ1
Full Question:
See attached image
looking at waves a and b. which description correctly describes the waves?; which example is not a part of the electromagnetic spectrum?
Electromagnetic waves are transverse waves composed by the perpendicular oscillating electric and magnetic fields.
EM waves have both Electrical and magnetic features.
they travel in the velocity of light (3*10⁸ ms⁻¹)
Electromagnetic spectrum is obtained according to their wave length and the frequency. Due to wave length range it's categorized. Here is the decreasing order of wave length and increasing order of different wave types in electromagnetic spectrum
Examples,
Radio WaveMicro WaveIR waveLight WaveUV raysX raysGamma raysCosmic raysWhen electromagnetic radiation interacts with single atoms and molecule, its behavior also depends on the amount of energy per quantum(photon)it carries wave number =1/wavelength in cm speed of light=wavelength x frequency energy = Planck's constant x frequency.
Therefore, electromagnetic spectrum depends on wavelength and frequency
To know more about Electromagnetic, refer: https://brainly.com/question/9184100
#SPJ4
What are three ways you could cause the acceleration of a moving car?; What are the 3 different ways you can accelerate?; What causes the acceleration of a car?; What are the ways to accelerate?
The three ways to acceleration a moving vehicle are to depress the accelerator pedal, depress the brake, push the vehicle, or exert external force.
The rate at which the velocity of an object varies in relation to time is known as acceleration. Accelerations exist in vector quantities (in that they have magnitude and direction). The object's acceleration is determined by the direction of the net force acting on it. The size of the net balance of all external forces acting on the item is, in accordance with the materials used to create it, inversely proportional to its mass, but the magnitude of the net resultant force is directly proportional to the net force.
A moving object's rate of change in direction and speed over time is called acceleration. It is said to be accelerating when anything goes faster or slower. Due to the frequent change in direction, motion on a circle accelerates even while the speed is constant.
Therefore, applying the brake, pushing the car, or applying external force are the four ways to accelerate a moving vehicle. The three other methods are pressing the accelerator pedal.
Learn more about Acceleration here:
brainly.com/question/3046924
#SPJ4
A nozzle with a radius of 0.21 cm is attached to a garden hose with a radius of 0.95 cm that is pointed straight up. The flow rate through hose and nozzle is 0.45 L/s. Randomized Variables r, = 0.21 cm r= 0.95 cm O=0.45 L/S 50% Part (a) Calculate the maximum height to which water could be squirted with the hose if it emerges from the nozzle in m. Grade Summary h2= Deductions 0% Potential 100% sin() cos t an() ( 7 8 9 HOME Submissions cotan asin() acos M ^ Attempts remaining: 7 4 5 6 (3% per attempt) atan acotan sinh( * 1 2 3 = detailed view cosh tanh cotanh + - 0 END Degrees O Radians NO BACKSPACE CLEAR Submit Hint Feedback I give up! Hints: 0% deduction per hint. Hints remaining: 4 Feedback: 0% deduction per feedback. 50% Part (b) Calculate the maximum height (in cm) to which water could be squirted with the hose if it emerges with the nozzle removed, assuming the same flow rate.
The greatest height that the water can depart through the two points using fluid mechanics expressions is as follows:
1) y = 0.20 m is the maximum height that the water can exit the hose at.
2) The water shoots out of the nozzle at a maximum height of 68.6 meters.
When the water exits the hose, the pressure is atmospheric, and it is the same when it reaches its greatest point. P1 = P2
12 v12 + g y1 = 12 v22 + g v2
At the highest point of trajectory the velocity must be =zero.
y₂- y₁ = [tex]v^{2} /2g[/tex]
Let's calculate
Δy = 0.2 m.
Using Bernoulli's equation, the speed of the water is the highest point=0.
Δy = 68.6m
What law contains the Bernoulli equation?The law of energy conservation is the foundation of Bernoulli's principle, to the fullest extent possible. At various sites when liquid is flowing under a constant pressure differential, the whole energy of the liquid—including pressure energy, potential energy, and kinetic energy—is equalized.
To know more about Bernoulli equation visit;-
https://brainly.com/question/13093946
#SPJ4
❧ What is the dispersion of White Light?
When white light is passed through a glass prism it splits into its spectrum of colours (in order violet, indigo, blue, green, yellow, orange and red) and this process of white light splitting into its constituent colours is termed as dispersion.
What causes the dispersion of white light?Cause of Dispersion: When white light passes through a glass prism, its constituent colours (red, orange, yellow, green, blue, indigo, violet) travel with different speeds in the prism because refractive index is color dependent. This causes the dispersion of light.The bending of the colors when they pass through the prism depends on its wavelength. So violet color has a shortest wavelength as a result it bends the most and followed by indigo, blue, green, yellow, orange and red respectively.The splitting of light into its component colors is called dispersion of light. Dispersion of white light can be done by a glass prism. The inclined refracting surface of a glass prism shows this phenomena.When a prism is placed in a room and a beam of white light is allowed to fall on one of its refracting faces. It is found that light coming out from the other face of the prism is split into seven colors (violet, indigo, blue, green, yellow, orange, red).To learn more about White light refer to:
https://brainly.com/question/2264818
#SPJ1
Describe the motion of a particle with position (x, y) as t varies in the given interval. (For each answer, enter an ordered pair of the form x, y.) x = 1 + sin(t), y = 5 + 6 cos(t), 1/2 Sts 2n The motion of the particle takes place on an ellipse centered at (x,y) = ( As t goes from 1/2 to 21, the particle starts at the point (x,y) (O and moves clockwise three-fourths of the way around the ellipse to (x,y) = Need Help? Read It
The particle moves along an ellipse with its center at (1,5). As t changes from π/2 to 2π, the particle begins at the location (6,1) and travels clockwise three-fourths of the way around the ellipse to (5,7).
According to the Pythagorean identity, sin²θ+cos²θ=1. The equation of the ellipse when the horizontal axis (main axis) is parallel to the y-axis is given as [tex]\frac{(x-h)^2}{b^2}+\frac{(y-k)^2}{a^2}=1[/tex] where (h,k) is the ellipse center, a is the major axis length, and b is the minor axis length.
Given x = 1 + sin(t) and y = 5 + 6 cos(t), π/2 ≤ t ≤ 2π. Then,
[tex]\begin{aligned}x& = 1 + \sin(t)\\\sin t&=x-1\end{aligned}[/tex]
and
[tex]\begin{aligned} y&= 5 + 6 \cos(t)\\\cos t&=\frac{y-5}{6}\end{aligned}[/tex]
Then, using Pythagorean identity,
[tex]\begin{aligned}\cos^2t+\sin^2t&=1\\\left(\frac{y-5}{6}\right)^2+\left(\frac{x-1}{1}\right)^2&=1\end{aligned}[/tex]
Comparing the above equation with the equation of an ellipse, we can tell, the center (h,k) is (1,5). Here, a is 6 and b is 1. So the radius of the vertical axis (major axis) is 6 and the radius of the horizontal axis (minor axis) is 1.
As t starts from π/2 to 2π, the particle starts at the point,
(5+1, 1) = (6,1)
And the particles move three-fourths of the ellipse in a clockwise direction to,
(5, 1+6) = (5,7)
Therefore, the blanks can be filled with (1,5), (6,1), and (5,7).
To know more about ellipses:
https://brainly.com/question/14281133
#SPJ4
time quantum is defined in: group of answer choices shortest job scheduling algorithm priority scheduling algorithm round robin scheduling algorithm multilevel queue scheduling algorithm
In the round robin scheduling algorithm, time quantum is specified. As part of a theory that contends that time is not continuous, a chronon is a discrete and indivisible "unit" of time that is proposed.
A preemptive scheduler permits a certain process to operate for a brief period of time known as a quantum (or time slice). The process is put back in the ready queue after this amount of time and another one is put into the run state (i.e., the scheduler ensures that the processes take turns to run). Round Robin Scheduling fixes the time quantum before scheduling the processes such that no one process receives more CPU time than one time quantum at a time. The response time of the processes is too long if time quantum is too large, which could not be acceptable in an interactive environment.
To learn more about quantum click here https://brainly.com/question/28943816
#SPJ4
based on this passage, which of the following might be true about the early history of modern physics? select it had a very practical component select it was uninteresting to most people select none of these select it was often combined with many topics studied in philosophy select it was underdeveloped and primitive
True statement about the early history of modern physics is option A: it had a very practical component.
The early history of physics could explain everything out of others, thus it had a practical component. The minds of almost all thinkers are left with the patterns of scientific reasoning and apotheosis in modern physics. From the time of the early renaissance to the nineteenth century, physics represented the ultimate expression of scientific investigation for almost all thinkers. The unchanging principles of all motion and life on earth are being derived from its static laws. By the nineteenth century, it seemed that most of science had already been "cleared up," and only a few remaining details remained.
This cosmology was overthrown by the idea of a universal morphing of kinds, which completely altered it. The very view of science held by most people was among the things that had to change in light of Darwin’s work.
To know more about physics, refer to the following link:
https://brainly.com/question/26765510
#SPJ4
total internal reflection can occur when light is traveling from air to its interface with water air to its interface with glass glass to its interface with air water to its interface with glass click here to check your answer 11.11 pts.100% 25% try penalty
The total internal reflection can occur when light is traveling from glass to its interface with air.
Total internal reflection occurs when light moves from denser to rarer and the angle of incidence is greater than the critical angle.
Total Internal Reflection occurs when light travels from water to air, but it does not occur when light travels from air to water. Total Internal Reflection would occur for light travelling from water to air, but not for light travelling from water (n=1.333) to crown glass (n=1.52). TIR occurs when the angle of refraction approaches 90 degrees before the angle of incidence approaches 90 degrees. Light can only bend away from the normal if the angle of refraction is greater than the angle of incidence. Because light only bends away from the normal when passing from a denser medium to a denser medium, this would be a necessary condition for total internal reflection.
Thus, TIR occurs when light is travelling from glass towards air.
To learn more about total internal reflection refer here
https://brainly.com/question/28231417
#SPJ4
blocks a and b of masses m and 3m, respectively, are on a horizontal surface of negligible friction. a horizontal force fa is exerted on block a, as shown. if the force exerted by block b on block a has a magnitude f, the magnitude of fa is
If the force exerted by block b on block a has a magnitude f, the magnitude of fa is is f, because according to the newtons thied law of motion, the every force there is equal and opposite reaction.
Friction is the force resisting the relative motion of sturdy surfaces, fluid layers, and material factors sliding towards each specific. There are numerous styles of friction: Dry friction is a strain that opposes the relative lateral movement of two stable surfaces in touch.
Friction is a shape of contact pressure. It exists between the surfaces that are in touch. The frictional force relies upon on the character of the floor in contact. The rougher the ground, the extra the friction is involved. The frictional force is proportional to the urgent pressure, that is the burden of the body. it's miles impartial of the place of the touch.
Learn more about friction here:-https://brainly.com/question/24338873
#SPJ4
a 2.4 kg purse is dropped from the top of the leaning tower of pisa and falls 55 m before reaching the ground with a speed of 27 m/s. What was the average force of air resistance?
The average force of air resistance is 18.36N.
A force is an influence that can change the motion of an object. A force can cause an object with mass to change its velocity (e.g. moving from a state of rest), i.e., to accelerate. Force can also be described intuitively as a push or a pull. A force has both magnitude and direction, making it a vector quantity. It is measured in the SI unit of newton (N). It is a standard mechanical quantity. Force is represented by the symbol F (formerly P).
Given;
mass=2.4Kg
Hight=55m
Final velocity (v)=27m/s
Noe from kinematics
[tex]v^{2} =u^{2} +2ah[/tex]
Putting the value
[tex]0^{2} =(27)^{2} +2a*55[/tex]
so, a=4.4m/s^2
now, By applying newton's law
mg-F=ma
F=m(g-a)
=2.4(9.8-4.4)
=18.36N
Learn more about Force here:
https://brainly.com/question/12785175
#SPJ4
The spring is compressed by 10 cm. It launches the block across a frictionless surface with speed 0.50. The two springs in are identical to the spring of Figure a. They are compressed by the same 10 cm and used to launch the same block. What is the block's speed now?
The block's speed when two springs used to launch the same block is 0.71 m/s.
The problems not complete, look at the attachment to see the picture. In picture (2) two springs paralleled. The constant for two paralleled springs
k = k₁ + k₂
k = 25 + 25
k = 50 N/m
When the springs compressed, the conservation energy law applies.
K.E block + P.E springs = K.E' block + P.E' springs
The block initially stop.0 + 0.5 × k × Δx² = 0.5 × m × v² + 0
k × Δx² = m × v²
50 × 0.1² = 1 × v²
0.5 = v²
[tex]v = \sqrt{0.5}[/tex]
v = 0.71 m/s
Learn more about conservation energy law here: https://brainly.com/question/11550087
#SPJ4
suppose the ball is dropped. what force is exerted on it while it is? identify the reaction force in this case as in free body diagram
When a ball is dropped, the gravitational force that the Earth's gravitational field produces when the object descends downhill is exerted.
In a simple scenario, the ball falls in accordance with the direction of force of gravity, which is always downward. Gravitational acceleration on Earth is 9.8 m/s2 (g=9.8 m/s2). In essence, this indicates that the ball's velocity will increase by 9.8 m/s for every second while it is falling.
You should follow the steps below to determine the net force in one dimension. List every force influencing the thing. by depicting the object's free body in a diagram. Diirection upward is favorable, while diirection downhill is adverse. The net response force downward is obtained by subtracting the positive and negative forces from each other.
To know more about Force:-
brainly.com/question/13634821
#SPJ4
Each item below can be used to measure the distances of astronomical objects. Rank them according to how far away each method works, from nearest to farthest.
1. Cepheids
2. Radar ranging
3. White dwarf supernovae
4. Parallax
Radar ranging, parallax, Cepheids, white dwarf supernovae
Each item below can be used to measure the distances of astronomical objects. Rank them according to how far away each method works, from:
Radar ranging > parallax > Cepheids > white dwarf supernovae
The plain displacement or the difference in apparent course of an item as seen from specific factors not on a immediately line with the item. especially : the angular distinction in direction of a celestial frame as measured from two points on the earth's orbit.
Parallax is the discovered displacement of an item due to the trade of the observer's point of view. In astronomy, it's far an irreplaceable tool for calculating distances of some distance away stars.
Parallax mistakes is whilst the pointer of a device looks like it is at a special analyzing when study to the aspect in comparison to when examine face-on. This is because of the gap among the size and the pointer.
Learn more about parallax here:- https://brainly.com/question/29210252
#SPJ4