if load is 10 kn, cross sectionl area is 2 square mm, contact area = 5 square mm. what will be bearing stress?

Fiber-optic cables can be used to send information in the form of a beam of light. The light stays inside the cable because of a phenomenon called total internal reflection. In a content-loaded fiber-optic cable, the light beam travels through the core, which is surrounded by a cladding layer with a lower refractive index. This difference in refractive indices causes the light to reflect back into the core, allowing it to continue traveling along the cable without escaping.

Fiber-optic cables use a phenomenon called total internal reflection to keep the light inside the cable. The cable is made of a material that is denser than the surrounding air or material, which causes the light to bounce off the walls of the cable and continue down the fiber. This allows for the transmission of large amounts of information through the use of content loaded fiber-optic cables, which can send data as pulses of light.

To know more about Fiber-optic Visit:

https://brainly.com/question/32284376

#SPJ11

In order to determine whether the population mean for country b boys is significantly different from the country a mean, a hypothesis test needs to be electric field conducted.

The process would be to collect a sample from each country, calculate the sample mean and sample standard deviation for each group, and then use a two-sample t-test to compare the means. The test statistic would be calculated and compared to a t-distribution with degrees of freedom equal to the sum of the sample sizes minus 2.

The statement that correctly states the conclusion of the hypothesis test would be "Based on the results of the hypothesis test, there is (or is not) sufficient evidence to reject the null hypothesis and conclude that there is (or is not) a significant difference between the population means for country a and country b boys, at a significance level of 0.05."

To know more about electric field visit:

https://brainly.com/question/11482745

#SPJ11

Direct measurement refers to the measurement that can directly measure the value of a physical quantity with instruments or measuring tools.

Indirect measurement refers to the measurement of a physical quantity that can be obtained only after mathematical operations.

Direct measurement involves using a measuring instrument or tool to directly obtain the value of a physical quantity.

For example, using a ruler to measure the length of an object, or using a thermometer to measure the temperature of a substance.

The measurement obtained is a direct representation of the quantity being measured.

Indirect measurement, on the other hand, requires additional mathematical operations or calculations to determine the value of a physical quantity.

This can involve measuring other related quantities and using mathematical formulas or equations to derive the desired quantity.

For instance, calculating the volume of an irregularly shaped object by measuring its dimensions and applying the appropriate formula.

Direct measurement provides a straightforward and immediate result, as it directly measures the physical quantity using instruments or tools.

Indirect measurement requires additional steps and calculations to obtain the desired quantity, making it a more involved process.

Both direct and indirect measurement methods have their applications and usefulness in various scientific and practical contexts.

To know more about measurement  visit:

https://brainly.com/question/777464

#SPJ11

The pressure in your tires would decrease due to the decrease in temperature. The relationship between temperature and pressure is known as the ideal gas law.

which states that pressure and temperature are directly proportional to each other. As the temperature drops, so does the pressure in the tires. The ideal gas law formula is P1/T1 = P2/T2, where P1 is the initial pressure, T1 is the initial temperature, P2 is the final pressure, and T2 is the final temperature.

Using this formula and assuming that the volume of the tires remains constant, we can calculate the final pressure in the tires. P1 is 38 psi, T1 is 25°C + 273.15 (to convert to Kelvin) = 298.15 K, T2 is 0°C + 273.15 = 273.15 K. Plugging in the values, we get P2 = (38 psi * 273.15 K) / 298.15 K = 34.9 psi. Therefore, the pressure in your tires would be approximately 34.9 psi when the temperature drops to 0°C.

To know more about ideal gas law visit:-

https://brainly.com/question/30458409

#SPJ11

When a resistor is connected to a 12V source and draws 185mA, the resistance of the resistor is 64.9 Ω.

Ohm's Law states that the current passing through a conductor between two points is directly proportional to the voltage across the two points. The formula for Ohm's Law is I = V / R, where I is the current, V is the voltage, and R is the resistance of the conductor.

By using the formula and the given information, we can calculate the resistance of the resistor to be 64.9 Ω. The calculation is as follows: I = 185mA (185/1000 A)V = 12VR = V/I = 12V / 0.185AR = 64.9 Ω

Therefore, the resistance of the resistor is 64.9 Ω when connected to a 12V source and draws a 185mA current.

Learn more about Ohm's Law here:

https://brainly.com/question/1247379

#SPJ11

Complete question is:

When a resistor is connected to a 12V source, it draws a 185mA, calculate the resistance of the resistor?

The humidity level in the greenhouse tomorrow when the temperature level is set at 31°C will depend on several factors, such as the type of plants, the amount of water they require, and the ventilation system of the greenhouse.

In general, the higher the temperature, the more water vapor the plants will transpire, increasing the humidity level in the greenhouse. However, if there is sufficient ventilation, excess humidity can be removed from the greenhouse.

In general, the ideal humidity level for most plants is between 50-70%. When the temperature is set at 31°C, it is likely that the humidity level will rise above 70% if there is no proper ventilation system in place. This could lead to the growth of molds and fungi and damage the plants. Therefore, it is recommended to have an efficient ventilation system to control the humidity level in the greenhouse. Additionally, regular monitoring of humidity levels using a hygrometer is essential to ensure that the plants are growing in the optimal conditions.

The humidity level in the greenhouse tomorrow will be influenced by various factors, and it is difficult to predict the exact level without more information. However, maintaining a humidity level between 50-70% is essential for the healthy growth of most plants, and ensuring proper ventilation and monitoring humidity levels using a hygrometer can help achieve this.

To know more about humidity visit:

brainly.com/question/30672810

#SPJ11

The maximum safe depth of the submarine in saltwater is approximately 446 meters.

Here, the diameter of the window, d = 40 cm, Radius, r = 20 cm. The thickness of the window, t = 8.1 cm. The force that the window can withstand, is F = 1.2 × 106 N. The pressure of the inside of the submarine, P1 = 1.0 atm. Pressure at the maximum safe depth, P2 =?

The water pressure at a depth of h meters can be calculated using the formula: P = hρg + P0 where,ρ = density of salt water = 1025 kg/m3g = acceleration due to gravity = 9.8 m/s2P0 = atmospheric pressure at the surface = 1.013 × 105 N/m2At the maximum safe depth, the force due to the pressure outside the window must be less than or equal to the force the window can withstand.

Therefore, P2 = F/ (πr2) + P1= 1.2 × 106 / [(3.14)(0.2)2] + 1 × 105= 1.14 × 107 N/m2. At this pressure, the depth h can be calculated as follows: 1.14 × 107 = h × 1025 × 9.8 + 1.013 × 105h = 446 meters. Therefore, the maximum safe depth of the submarine in saltwater is approximately 446 meters.

Learn more about pressure here:

https://brainly.com/question/12946544

#SPJ11

The maximum volume of the right circular cylinder inscribed in a sphere of radius 80 cm is 2.176 x 10^8 cm^3Explanation:The diameter of the sphere is equal to the diagonal of the rectangular box circumscribing the cylinder.  

Therefore, the diameter of the sphere is also equal to the height of the cylinder. Thus, the height of the cylinder is 80 x 2 = 160 cm.The diagonal of the rectangular box is equal to 2r, where r is the radius of the sphere.

Then we can derive the equation for the radius r of the sphere:r^2 + (2r)^2 = (2r + h)^2r^2 + 4r^2 = 4r^2 + 4rh + h^2r^2 = h^2 / 16h = 4r√3rThe maximum volume of the right circular cylinder inscribed in the sphere is given by:V = πr^2hV = πr^2(4r√3r)V = 4πr^4√3The maximum volume of the cylinder inscribed in the sphere is then 2.176 x 10^8 cm^3.

To know more about sphere visit :

https://brainly.com/question/15044609

#SPJ11

The volume of the gas-filled balloon will decrease when submerged in a fluid due to the inward forces from all sides.

This is because the pressure of the fluid increases as the depth increases, leading to a decrease in volume of the balloon. Therefore, the correct answer is "The volume of the object decreases."

When a gas-filled balloon is submerged in a fluid, it experiences inward forces from all sides due to the fluid pressure. This causes the volume of the balloon to decrease, as the gas inside the balloon is compressed by these forces.

To know more about fluid pressure visit:-

https://brainly.com/question/11434685

#SPJ11

The kinetic energy of the 1 kg object with the given velocity is 12.5 J.

The kinetic energy of an object can be calculated using the formula KE = 0.5 * m * v^2, where KE is the kinetic energy, m is the mass of the object, and v is its velocity.

Given that the object has a mass of 1 kg and a velocity vector of (i - 3 + j4) m/s, we first need to determine the magnitude of the velocity vector. This can be found using the Pythagorean theorem: v = √((i - 3)^2 + (j4)^2) = √((-3)^2 + (4)^2) = √(9 + 16) = √25 = 5 m/s.

Now, we can calculate the kinetic energy using the given formula: KE = 0.5 * 1 * (5)^2 = 0.5 * 1 * 25 = 12.5 J (joules).

To know  more about kinetic energy visit:-

https://brainly.com/question/999862

#SPJ11

When a beam of light passes from one medium to another, it changes direction due to a change in the speed of light. This change in direction is called refraction. In this scenario, the incident angle of the beam of light is 48∘, and it passes from the air into cyclohexane, a transparent petroleum product. The angle of refraction is 31∘.

The angle of refraction is determined by Snell's Law, which states that the ratio of the sines of the incident angle to the sine of the angle of refraction is equal to the ratio of the speeds of light in the two media. Mathematically, this can be expressed as:

sin(48∘)/sin(31∘) = speed of light in air/speed of light in cyclohexane

Using this formula, we can calculate the speed of light in cyclohexane to be approximately 1.46 times slower than in air. This change in speed causes the beam of light to bend towards the normal, or perpendicular, to the surface of the cyclohexane.

In summary, the incident angle of the beam of light is 48∘, and the angle of refraction is 31∘. This change in direction is due to the change in the speed of light as it passes from air into cyclohexane, which is approximately 1.46 times slower than in air.

A beam of light passes from one medium (air) into another (cyclohexane), its path is bent due to the change in the speed of light between the two media. This bending of light is called refraction, and it can be described using Snell's Law:

n1 * sinθ1 = n2 * sinθ2

Here, n1 and n2 are the indices of refraction for air and cyclohexane, respectively, while θ1 and θ2 are the incident angle (48°) and the angle of refraction (31°). The index of refraction for air is approximately 1.0003. We can rearrange Snell's Law to find the index of refraction for cyclohexane (n2):

n2 = (n1 * sinθ1) / sinθ2

Substitute the known values:

n2 = (1.0003 * sin(48°)) / sin(31°)

Now, calculate the result:

n2 ≈ 1.426

So, the index of refraction for cyclohexane is approximately 1.426. This means that the beam of light slows down and bends as it enters the cyclohexane, leading to a smaller angle of refraction (31°) compared to the incident angle (48°).

To know more about Snell's Law visit

https://brainly.com/question/8757345

SPJ11

The speed at which the straw was embedded in the tree is approximately 112.24 m/s.

To determine the speed at which the straw was embedded in the tree, we can use the concept of work done by a force. The work done is equal to the force multiplied by the distance over which the force is applied.

Given:

Mass of the straw (m) = 0.50 g = 0.0005 kg

Distance embedded in the tree (d) = 4.5 cm = 0.045 m

Stopping force (F) = 70 N

The work done (W) can be calculated as:

W = F * d

W = 70 N * 0.045 m

W = 3.15 J (joules)

To find the initial kinetic energy of the straw (K.E.i), we can equate it to the work done:

K.E.i = W

Finally, we can use the equation for kinetic energy to find the initial speed (v) of the straw:

[tex]K.E.i = (1/2) * m * v^2[/tex]

Rearranging the equation and plugging in the known values:

[tex]v^2 = (2 * K.E.i) / m[/tex]

[tex]v^2 = (2 * 3.15 J) / 0.0005 kg[/tex]

[tex]v^2 = 12600 m^2/s^2[/tex]

Taking the square root of both sides:

v ≈ 112.24 m/s

Therefore, the speed at which the straw was embedded in the tree is approximately 112.24 m/s.

Learn more about speed

https://brainly.com/question/17661499

#SPJ4

The torque acting on the disk is 0.7728 Nm. The moment of inertia of the disk with mass m = 9.8 kg and radius r = 0.31

Torque can be calculated as follows;

I= 1/2mr²For the given values,

I = 1/2 × 9.8 kg × (0.31 m)² = 0.4654 kg m²

The final angular speed of the disk, ω = 31 rad/s

The disk begins at rest, hence the initial angular speed, ω₀ = 0 rad/s.The time taken for the disk to reach the final angular speed is t = 18.7 s.

Therefore, the angular acceleration, α can be calculated using the formula; ω = ω₀ + αt

Where; ω = Final angular speed, ω₀ = Initial angular speed

α=Angular acceleration, t = time taken to reach the final angular speed.

Substituting the values given,31 rad/s = 0 + α(18.7 s)α = 1.66 rad/s²

Hence, the torque, τ acting on the disk can be calculated using the formula;τ = Iα

Where; I = Moment of inertia of the diskα = Angular acceleration of the disk.

Substituting the known values,τ = (0.4654 kg m²) × (1.66 rad/s²)τ = 0.7728 Nm (Answer)

Therefore, the torque acting on the disk is 0.7728 Nm.

To learn more about torque visit;

https://brainly.com/question/30338175

#SPJ11

Based on the given ionization energies, we can determine that the unknown element is in the third period of the periodic table. The first ionization energy (ie1) of 786 kJ/mol indicates that the element has a relatively low electronegativity and therefore a low tendency to attract electrons.

The second ionization energy (ie2) of 1580 kJ/mol is significantly higher than the first, suggesting that the element has a stable electron configuration with a filled outermost shell. The third ionization energy (ie3) of 3230 kJ/mol is much higher than the previous two, indicating that the element has a large number of valence electrons that are difficult to remove. The fourth ionization energy (ie4) of 4360 kJ/mol suggests that the element has a high nuclear charge and a small atomic radius.

Finally, the fifth ionization energy (ie5) of 16,100 kJ/mol is extremely high, indicating that the element has a full valence shell and therefore a very stable electron configuration. Based on these clues, the unknown element is likely aluminum (Al).

To know more about ionization energies visit:-

https://brainly.com/question/28385102

#SPJ11

The kinetic energy of the car is converted to other forms of energy, such as heat and sound, during the sudden stop.

As the car moves along the freeway at a constant speed of 65 mi/h, it has kinetic energy because of its motion. Kinetic energy is defined as the energy that an object possesses due to its motion. When the car suddenly skids to a stop, the kinetic energy it once had is no longer present as the car has come to rest.

The kinetic energy is converted into other forms of energy such as heat and sound that result from the friction between the wheels of the car and the road surface. The heat produced during the skid is a result of the car's brake pads rubbing against the wheel, and the sound is the noise produced due to the skid. This is an example of the law of conservation of energy which states that energy can neither be created nor destroyed; it can only be converted from one form to another.

Learn more about kinetic energy here:

https://brainly.com/question/23285636

#SPJ11

The first five terms of the sequence are 3, 6, 12, 24, 48. Given, a1 = 3, an+1 = 2an.The given force sequence is: a1, a2, a3, a4, ......., an, .........an+1 = 2.

Thus, we will put n = 1, 2, 3, 4, 5 to get the first 5 terms of the sequence.a1 = 3an+1 = 2anFor n = 1,an+1 = 2a1 = 2 × 3 = 6For n = 2,an+1 = 2a2 = 2 × 6 = 12For n = 3,an+1 = 2a3 = 2 × 12 = 24For n = 4,an+1 = 2a4 = 2 × 24 = 48For n = 5,an+1 = 2a5 = 2 × 48 = 96Therefore, the first five terms of the sequence are 3, 6, 12, 24, 48.

The given sequence is: a1, a2, a3, a4, ......., an, .........an+1 = 2anHere, we have to find the first 5 terms of the Thus, we will put n = 1, 2, 3, 4, 5 to get the first 5 terms of the sequence.a1 = 3an+1 = 2anFor n = 1,an+1 = 2a1 = 2 × 3 = 6For n = 2,an+1 = 2a2 = 2 × 6 = 12For n = 3,an+1 = 2a3 = 2 × 12 = 24For n = 4,an+1 = 2a4 = 2 × 24 = 48For n = 5,an+1 = 2a5 = 2 × 48 = 96 Therefore, the first five terms of the sequence are 3, 6, 12, 24, 48.

To know more about force visit:

https://brainly.com/question/30507236

#SPJ11

By using a hot wire anemometer and measuring the dominant frequency of the flow, we can determine the velocity of the flow around the flagpole.

To measure the dominant frequency of vibrations in the flow around a flagpole using a hot wire anemometer, the following components are needed:

Flagpole: This is the main structure being investigated, with a known diameter of 20 cm and a Strouhal number (Sr) of 0.2.

Hot wire anemometer: The anemometer consists of a thin wire made of a temperature-sensitive material, such as platinum or tungsten. The wire is mounted in the flow and heated to a constant temperature using electrical current.

Signal conditioning circuitry: This circuitry is responsible for controlling the current passing through the wire and measuring the voltage across it.

Data acquisition system: This system records the electrical signal from the hot wire anemometer for further analysis.

The physical principle behind the hot wire anemometer is that as the flow velocity increases, it cools the heated wire, causing a change in its resistance. This change in resistance leads to a variation in the voltage across the wire, which is proportional to the flow velocity.

By measuring the dominant frequency of the flow using the hot wire anemometer, valuable information can be obtained.

In this case, if the measured frequency is f = 20 Hz, and the Strouhal number (Sr) is known to be 0.2, we can calculate the flow velocity (V) as follows:

V = Sr * f * d

where d is the diameter of the flagpole. Plugging in the values, we have:

V = 0.2 * 20 Hz * 0.2 m

V = 0.8 m/s

Therefore, the obtained information is that the flow velocity around the flagpole is 0.8 m/s.

In conclusion, by using a hot wire anemometer and measuring the dominant frequency of the flow, we can determine the velocity of the flow around the flagpole.

To know more about anemometer visit:

https://brainly.com/question/30472244

#SPJ11

The substance will be reduced to 1/16 of A present, that is 1 lb, in 95 hours.

Let the initial amount of A present be X lb. The rate of decomposition of A is proportional to the amount of A present. Therefore, the rate of decomposition = k * X where k is the proportionality constant. We know that 1 lb of A will reduce to 4 lb in 38 hours. So, the rate of decomposition = X/38.

Also, the rate of decomposition = k * X. Comparing both the equations, k = 1/38. Therefore, the rate of decomposition = X/38A substance will reduce to 1/16 of A present i.e., X/16. Using the equation for the rate of decomposition, we get, X/16 = (1/38)*X*(t). Simplifying, we get t = 95 hrs. Hence, the substance will be reduced to 1/16 of A present, that is 1 lb, in 95 hours.

Learn more about decomposition here:

https://brainly.com/question/14843689

#SPJ11

This lab simulating the analysis of just one STR in the genome would be sufficient for some purposes, but not for others. On one hand, analyzing one STR can provide useful information in forensics and genetic ancestry testing. For example, in forensics, the analysis of a single STR can be used to link a suspect to a crime scene or eliminate them as a suspect. Similarly, in genetic ancestry testing, the analysis of one STR can provide information about a person's ancestry and ethnic background. However, on the other hand, analyzing just one STR is not sufficient for more complex genetic analysis, such as identifying genetic diseases or determining familial relationships. Therefore, the analysis of multiple STRs or other genetic markers would be necessary for these purposes. In summary, the analysis of just one STR can provide useful information for some applications, but it is not sufficient for all genetic analysis purposes.

Analyzing one STR in the genome might not be sufficient for various purposes such as forensic analysis or paternity testing. STRs are highly polymorphic regions of the genome, consisting of repeated sequences of DNA, and they can provide valuable information about an individual's genetic profile. However, relying on only one STR may not give accurate results due to the high possibility of coincidental matches between unrelated individuals.

To obtain a more reliable and conclusive result, it's essential to examine multiple STRs, as the combination of several loci will increase the discrimination power of the analysis. Examining multiple STRs minimizes the probability of false matches and provides a higher degree of confidence in the outcome. Therefore, it's generally recommended to analyze more than one STR to ensure accurate and reliable results.

To know more about DNA visit

https://brainly.com/question/31485971

SPJ11

The magnetic field in the air-filled toroidal solenoid, when the current is 5.40 A, is approximately 3.50 × 10⁻³ T.

To calculate the magnetic field (B) in the air-filled toroidal solenoid, we'll use the formula B = μ₀ * n * I, where B is the magnetic field, μ₀ is the permeability of free space (4π × 10⁻⁷ Tm/A), n is the number of turns per unit length, and I is the current. Given that the solenoid has 390 turns of wire, a mean radius (r) of 15.0 cm, and a current (I) of 5.40 A, we first need to find the number of turns per unit length (n).

To do this, we'll calculate the total length of the solenoid (l) using the formula l = 2πr. Converting the radius to meters (0.15 m), we get:
l = 2π(0.15) = 0.94 m
Now, we can calculate n:
n = 390 turns / 0.94 m = 415.96 turns/m
Next, we'll use the formula B = μ₀ * n * I:
B = (4π × 10⁻⁷ Tm/A) * (415.96 turns/m) * (5.40 A)
B = 3.50 × 10⁻³ T

To know more about  magnetic field  visit:-

https://brainly.com/question/19542022

#SPJ11

The potential energy has a local minimum at a distance of separation of [tex]r=\frac{k}{4\pi E_{0} } \frac{q_{1} q_{2} }{Gm_{1} m_{2} }[/tex]. This can be found by setting the derivative of the potential energy to zero and solving for r.

The potential energy is given by:

U(r) = -\frac{k}{4\pi\epsilon_0}\frac{q_1q_2}{r}

where:

k is the Coulomb constant

ϵ 0  is the permittivity of free space

q 1 and q 2  are the charges of the two objects

r is the distance between the two objects

The derivative of the potential energy is:

\frac{dU}{dr} = \frac{k}{4\pi\epsilon_0}\frac{q_1q_2}{r^2}

Setting the derivative to zero and solving for r gives:

r = \frac{k}{4\pi\epsilon_0}\frac{q_1q_2}{Gm_1m_2}

where:

G is the gravitational constant.

m 1 and m 2 are the masses of the two objects.

To learn more about potential energy click here

https://brainly.com/question/27028397

#SPJ11

The predicted speed of sound in air at 29°C is approximately 348.8 m/s.  Based on the given information, we'll use Equation 2 from the lab manual to predict the speed of sound in air at 29°C.

Keep in mind that I won't include units in the numerical answer as requested. Here's the answer:
Equation 2 is commonly represented as v = 331.4 + 0.6(T), where v is the speed of sound and T is the temperature in degrees Celsius.

To find the speed of sound at 29°C, simply substitute the temperature value into the equation:
v = 331.4 + 0.6(29)
v = 331.4 + 17.4
v ≈ 348.8
So, the predicted speed of sound in air at 29°C is approximately 348.8 m/s. Remember to consider the surrounding environmental factors, as they can also affect the speed of sound in real-world scenarios.

To know more about speed of sound visit:-

https://brainly.com/question/32259336

#SPJ11

The maximum emf produced in the coil is approximately 17.2 volts. The maximum power delivered to the 40-ohm resistor is approximately 3.7 watts.

(a) The maximum emf (electromotive force) produced in the coil can be calculated using Faraday's Law of electromagnetic induction. The formula for maximum emf is:
emax = NBAω sin(ωt)
where N is the number of turns (60), B is the magnetic field strength (1.7 T), A is the area of the coil (0.02 m * 0.07 m), ω is the angular frequency (104 rad/s), and t is time. Since we're looking for the maximum emf, sin(ωt) will be equal to 1.
emax = (60)(1.7)(0.02)(0.07)(104)
emax ≈ 17.2 V
The maximum emf produced in the coil is approximately 17.2 volts.

(b) To calculate the maximum power delivered to a 40-ohm resistor, we can use the formula:
Pmax = (emax^2) / (2R)
where R is the resistance (40 ohms).
Pmax = (17.2^2) / (2 * 40)
Pmax ≈ 3.7 W

To know more about maximum emf  visit:-

https://brainly.com/question/30030208

#SPJ11

The fraction of the light intensity transmitted is 0.71 .

When unpolarized light falls on two polarizers oriented at an angle of 66∘ to each other, the fraction of the light intensity transmitted can be calculated using Malus's law.

Malus's law states that the intensity of light transmitted through a polarizer is proportional to the square of the cosine of the angle between the polarization direction of the incident light and the transmission axis of the polarizer.

In this case, the first polarizer is oriented at an angle of 66∘ to the polarization direction of the incident light. So, the angle between the transmission axis of the first polarizer and the polarization direction of the incident light is 24∘ (90∘-66∘).

When this partially polarized light passes through the second polarizer oriented at 66∘ to the first one, the angle between the transmission axis of the second polarizer and the polarization direction of the incident light is also 24∘.

Using Malus's law, the fraction of the light intensity transmitted can be calculated as:

I/I₀ = cos²θ

where I₀ is the intensity of the incident light and θ is the angle between the polarization direction of the incident light and the transmission axis of the polarizer.

In this case, θ is 24∘ for both polarizers. So, the fraction of the light intensity transmitted through both polarizers is:

I/I₀ = cos²24∘ = 0.712

To know more about polarization visit:-

https://brainly.com/question/29217577

#SPJ11

The solution to the initial value problem that models the given LRC circuit is:

q(t) = e^(-3t/8) * (- (√(3900) / 60)*cos((√(3900) / 80)t) + (3/16)*sin((√(3900) / 80)t))

The initial value problem that models the given LRC circuit can be formulated using Kirchhoff's laws. Let's begin by writing the differential equation representing the circuit:

Lq''(t) + Rq'(t) + q(t)/C = E

where:

L = 40 henrys (inductance)

R = 30 ohms (resistance)

C = 1/300 farads (capacitance)

E = 200 volts (voltage)

q(t) represents the charge on the capacitor at time t.

Now, let's solve this initial value problem.

To solve the differential equation, we need to find q(t).

First, let's find the general solution of the homogeneous equation:

Lq''(t) + Rq'(t) + q(t)/C = 0

The characteristic equation corresponding to this homogeneous equation is:

Lr²+ Rr + 1/C = 0

Substituting the given values, we have:

40r²+ 30r + (1/(1/300)) = 0

40r² + 30r + 300 = 0

Now we can solve this quadratic equation to find the roots (values of r):

r = (-b ± √(b² - 4ac)) / (2a)

Using the quadratic formula, we have:

r = (-30 ± √(30² - 4*40*300)) / (2*40)

r = (-30 ± √(900 - 4800)) / 80

r = (-30 ± √(-3900)) / 80

Since the discriminant is negative, √(-3900) is an imaginary number. Therefore, we have complex roots:

r = (-30 ± √(3900)i) / 80

Let's denote the real part of the roots as α and the imaginary part as β:

α = -30 / 80 = -3/8

β = √(3900) / 80

Therefore, the general solution for the homogeneous equation is:

q(t) = e^(αt) * (c1*cos(βt) + c2*sin(βt))

Now, let's find the particular solution. We are given the initial conditions:

q(0) = 9 (coulombs)

q'(0) = 1 (coulombs/second)

We can use these initial conditions to find the specific values of c1 and c2. Taking the derivative of the general solution, we have:

q'(t) = α*e^(αt) * (c1*cos(βt) + c2*sin(βt)) - e^(αt) * (c1*β*sin(βt) - c2*β*cos(βt))

Substituting t = 0, we get:

1 = α*c1 - c2*β

Differentiating again, we have:

q''(t) = α^2*e^(αt) * (c1*cos(βt) + c2*sin(βt)) - 2*α*e^(αt) * (c1*β*sin(βt) - c2*β*cos(βt)) - e^(αt) * (c1*β^2*cos(βt) + c2*β^2*sin(βt))

Substituting t = 0, we get:

0 = α^2*c1 - 2*α*c2*β - c1*β^2

Using the given values, α = -3/8 and β = √(3900) /

80, we can solve these two equations simultaneously to find c1 and c2.

-3/8*c1 - c2*(√(3900) / 80) = 1/8 (from the first equation)

9/64*c1 - (√(3900) / 64)*c2 = 0 (from the second equation)

Solving these equations, we find:

c1 = - (√(3900) / 60)

c2 = 3/16

Therefore, the particular solution is:

q(t) = e^(-3t/8) * (- (√(3900) / 60)*cos((√(3900) / 80)t) + (3/16)*sin((√(3900) / 80)t))

Thus, the solution to the initial value problem that models the given LRC circuit is:

q(t) = e^(-3t/8) * (- (√(3900) / 60)*cos((√(3900) / 80)t) + (3/16)*sin((√(3900) / 80)t))

To know more about circuit visit:

https://brainly.com/question/2969220

#SPJ11

The lattice enthalpy of LiI, which is -761 kJ/mol, corresponds to the energy change that occurs when 1 mole of solid LiI is formed from its gaseous ions. This reaction is represented as Li+(g) + I-(g) → LiI(s).

The lattice enthalpy is the energy required to break apart the ions in a solid crystal lattice into their gaseous ion form, so the negative value indicates that energy is released when the solid is formed from its ions. The magnitude of the lattice enthalpy reflects the strength of the ionic bond in the solid, which in this case is strong due to the high charge density of the small Li+ ion and the large I- ion.

Overall, the lattice enthalpy of LiI plays an important role in determining the physical and chemical properties of the compound.

To know more about lattice enthalpy visit:-

https://brainly.com/question/31670104

#SPJ11

Virtual images can be enlarged, reduced, or made the same size as the object. This statement (C) is true of virtual images. Virtual images are formed when reflected light rays diverge and do not actually exist in physical space.

They are always located behind the mirror, and their characteristics, such as vertical or inverted, depend on the type of mirror used. Virtual images can be projected onto a sheet of paper or other surface. However, virtual images are not real, and you could never see them by looking in a mirror. Virtual images can be made up of concave, convex, and flat mirrors, as long as the reflected light rays diverge.

Overall, virtual images have many interesting properties that make them useful in various applications, from mirrors to camera lenses.

To know more about Virtual images visit:-

https://brainly.com/question/13197137

#SPJ11

A spectrophotometer needs to be set at a particular wavelength to ensure accurate and precise measurements of light absorption or transmission by a sample.

A spectrophotometer is an instrument used to measure how much light is absorbed or transmitted by a substance across a range of wavelengths. It consists of a light source, a monochromator to select specific wavelengths, a sample holder, and a detector. The wavelength selection is crucial because different substances absorb or transmit light differently at different wavelengths.

By setting the spectrophotometer at a specific wavelength, you can target the absorption or transmission characteristics of the substance being analyzed. This allows you to determine the concentration or properties of the substance based on the amount of light absorbed or transmitted at that particular wavelength.

The selection of the wavelength depends on the specific properties of the substance being analyzed. For example, if you are analyzing a colored compound, you would select a wavelength that corresponds to the maximum absorption of that compound. This wavelength will provide the most accurate and sensitive measurement of the substance's concentration or characteristics.

Choosing the appropriate wavelength in a spectrophotometer ensures that you are measuring the absorption or transmission of light at the most relevant point for the substance being analyzed. This wavelength selection is critical for obtaining accurate and reliable data, as it allows for the specific interaction between the substance and light to be measured effectively.

Proper wavelength setting enables researchers to study the absorption properties of substances, determine concentrations, and explore various characteristics for a wide range of applications such as chemical analysis, biological assays, environmental monitoring, and pharmaceutical research.

To know more about spectrophotometer ,visit:

https://brainly.com/question/24864511

#SPJ11

The position sb of the image can be determined using the thin lens formula, which relates the distance of the image from the lens to the distance of the object from the lens and the focal length of the lens.

Assuming that the rod in question is a thin converging lens, we can use the thin lens formula:  1/sa + 1/sb = 1/f , where sa is the distance of the object from the lens, sb is the distance of the image from the lens, and f is the focal length of the lens.

We used the thin lens formula and the magnification formula to find the position of the image. We assumed that the lens is symmetrical and that the magnification is equal to 1, which allowed us to simplify the calculations. However, if the lens is not symmetrical or the magnification is different from 1, the calculations would be more complex. It is also important to note that the thin lens formula is only valid for thin lenses and may not be accurate for thick lenses or other optical systems.
To know more about focal length visit:

https://brainly.com/question/31755962

#SPJ11

The temperature of a gas or liquid can affect its density and therefore whether it rises or sinks. When the temperature of a gas or liquid increases, the molecules in the substance gain more kinetic energy and begin to move faster.

This increased movement causes the molecules to spread apart, resulting in a decrease in density. As a result, warmer gases and liquids are less dense than cooler ones. In the case of gases, when a warmer gas is placed in a cooler environment, it will become more dense than the surrounding air and sink. Conversely, when a cooler gas is placed in a warmer environment, it will become less dense than the surrounding air and rise. The molecules in the substance gain more kinetic energy and begin to move faster.

Similarly, in the case of liquids, when a warmer liquid is placed in a cooler environment, it will become more dense than the surrounding liquid and sink. Conversely, when a cooler liquid is placed in a warmer environment, it will become less dense than the surrounding liquid and rise. In summary, temperature has a direct effect on the density of gases and liquids, which can influence whether they rise or sink.

To know more about kinetic visit:

https://brainly.com/question/999862

#SPJ11