In a mercury tube, what happens when steam pressure drops to the cut-in pressure?

With good road conditions, the recommended minimum safe following distance is typically two seconds. This allows enough time for you to react if the vehicle in front of you suddenly stops or slows down.

The recommended minimum safe following distance with good road conditions is typically 2 seconds. This means that under normal circumstances, you should maintain a distance that takes at least 2 seconds to cover if the vehicle in front of you were to suddenly stop. This allows for enough reaction time and braking distance to avoid a collision. However, in adverse weather conditions or when driving at high speeds, it's important to increase this distance to ensure safety on the road.

Learn more about safety on the road here: brainly.com/question/29963706

#SPJ11

The purpose is to calculate the lift and drag coefficients and the normal, axial, lift, and drag forces for a specific airfoil configuration.

The given problem is related to aerodynamics and involves calculating lift and drag coefficients as well as corresponding forces for an airfoil at a given angle of attack.

The first step is to calculate lift and drag coefficients from the given normal and axial force coefficients.

Next, considering the airfoil as a 2D object with given velocity and altitude, the normal and axial forces can be found using the lift and drag coefficients.

Finally, using the normal and axial forces, the lift and drag forces can be calculated.

This problem involves applying principles of fluid dynamics and aerodynamics, as well as understanding the concepts of lift and drag in relation to airfoil performance.

Learn more about airfoil

brainly.com/question/30042281

#SPJ11

The lamp lumen depreciation factor applied to the design must relate to the depreciation of the lamp's lumen output over time.

This depreciation is affected by a variety of factors, including the quality of the lamp, the length of the lamp arc tube, and the re-lamping cycle. It is important to consider all of these factors when selecting a lamp and designing a lighting system. While the cost of the lamp is an important consideration, it should not be the sole factor in determining the lamp lumen depreciation factor. A more expensive lamp may have a longer lifespan and therefore a lower depreciation rate, but it may not be cost-effective in the long run if it requires frequent re-lamping. Similarly, the length of the lamp arc tube can affect the lamp's lumen output, but this factor alone does not determine the lamp lumen depreciation factor. The re-lamping cycle is also important to consider, as frequent re-lamping can be expensive and disruptive.

Ultimately, common sense should be applied when determining the lamp lumen depreciation factor. This means considering all of the relevant factors and making a decision that makes sense for the specific lighting application. By doing so, a lighting system can be designed that is both effective and cost-efficient.

Learn more about lumen here : https://brainly.com/question/28288611

#SPJ11

The dwell time for porosity in casted steel varies depends on factors like type of steel, the casting process used, casting parameters etc.

Porosity means the defect in casted steel that can significantly reduce its strength and durability. The dwell time for porosity refers to the amount of time that the molten steel remains in the mold before it solidifies and the porosity is formed.

This dwell time is affected by type of steel being cast, the casting process used and the specific casting parameters. For example, certain types of steel may require longer dwell times to achieve a more uniform solidification and reduce the risk of porosity.

Read more about dwell time

brainly.com/question/31260059

#SPJ4

The normal stress on the inclined plane ab is σ = 2.0625 ksi and the shear stress on the inclined plane ab is τ = 1.375 ksi.

Determining the normal stress and shear stress acting on the inclined plane ab, use the stress transformation equations.

The stress transformation equations relate the normal stress, σ, and shear stress, τ, on an inclined plane with the corresponding normal and shear stresses acting on a plane perpendicular to the inclined plane. The equations are:

σ = σn cos²θ + σs sin²θ ± 2τnsinθcosθ

τ = (σn - σs) sinθcosθ ± τn cos²θ ± τs sin²θ

where θ is the angle between the inclined plane and the plane of reference, σn and σs are the normal stresses acting on the plane of reference, τn and τs are the shear stresses acting on the plane of reference, and τns is the shear stress acting on the inclined plane.

Given that τ = 5.5 ksi and σ and τ are to be determined on the inclined plane ab. Assume a plane of reference perpendicular to the inclined plane ab with angle θ in between.

The angle θ between the inclined plane and the plane of reference is the complement of the angle of inclination, so θ = 90° - 30° = 60°.

Assuming that there are no normal stresses acting on the plane of reference, so σn = 0. Therefore, the stress transformation equations simplify to:

σ = σs sin²θ ± 2τnsinθcosθ

τ = (σs/2) ± τn cos²θ ± (τ/2)sin²θ

Solve for σs and τn by using the given value of τ and the fact that there are no normal stresses acting on the plane of reference:

τ = τns = 5.5 ksi

σs = τ/2 = 2.75 ksi

τn = 0

Substitute these values into the stress transformation equations to obtain the normal stress and shear stress on the inclined plane ab:

σ = σs sin²θ = 2.75 ksi sin²60° = 2.75 ksi (0.75) = 2.0625 ksi

τ = (σs/2) ± τn cos²θ ± (τ/2)sin²θ = 2.75 ksi/2 = 1.375 ksi

Therefore, the normal stress on the inclined plane ab is σ = 2.0625 ksi and the shear stress on the inclined plane ab is τ = 1.375 ksi.

learn more about stress transformation equations: https://brainly.com/question/29480452

#SPJ4

False. The position sensor of the Exhaust Gas Recirculation (EGR) valve is not mounted on top of the EGR valve.

The position sensor of the EGR valve is a linear potentiometer that measures the position of the valve, but it is typically mounted elsewhere in the EGR system. It may be mounted on the EGR control solenoid or on the intake manifold. The EGR system is designed to reduce the amount of nitrogen oxide emissions from the engine by recirculating some of the exhaust gases back into the intake manifold.

The EGR valve and its associated position sensor are key components of this system, and they work together to regulate the flow of exhaust gases and ensure that the engine is operating efficiently and emitting as few pollutants as possible.

Learn more about Exhaust here:

https://brainly.com/question/1404047

#SPJ11

Neither Technician A nor Technician B is completely correct. The firing voltage does have an impact on the burn time of the spark plug, but the direction of the effect depends on the specifics of the situation.

Generally, if the firing voltage is higher than normal, it can lead to a shorter burn time because the spark is stronger and can ignite the fuel mixture more quickly.

However, if the firing voltage is too high, it can also cause damage to the spark plug or ignition system. On the other hand, if the firing voltage is lower than normal,

it can lead to a longer burn time because the spark is weaker and may not ignite the fuel mixture as effectively. However, if the firing voltage is too low, it may also lead to misfires or incomplete combustion.

Therefore, both technicians are partially correct, but the relationship between firing voltage and burn time is more complex and depends on various factors.

To learn more about : voltage

https://brainly.com/question/28632127

#SPJ11

True. Spark plugs with iridium tips should not be re-gapped. Iridium is a very hard and brittle metal, and the fine wire that is used for the spark plug electrode is easily damaged.

In addition, the iridium tip is designed to be a specific size and shape to provide optimal performance and durability. Attempting to adjust the gap on an iridium spark plug can damage the electrode or alter its shape, which can result in poor performance, misfires, or engine damage.

Most manufacturers recommend replacing iridium spark plugs at the recommended interval rather than trying to adjust the gap. If the iridium spark plugs are damaged or worn, they should be replaced with new ones that have the correct gap and are designed to work with the specific engine and ignition system. This will help ensure that the engine runs smoothly, efficiently, and reliably.

Learn more about Spark here:

https://brainly.com/question/28267196

#SPJ11

One way to prevent being blinded by the glare of a car's headlights is to adjust your rearview mirror to its night setting. This will help reduce the amount of light reflecting directly into your eyes.

Additionally, you can try looking slightly away from the car's headlights and focus on the edge of the road to avoid being directly exposed to the light. Another option is to wear polarized sunglasses which can reduce glare and improve visibility.
One way to prevent being blinded by the glare of a car's headlights is to shift your focus towards the right edge of the road or the lane markings, instead of directly looking at the approaching headlights. This helps avoid the glare and maintain visibility of the road ahead.

To know more about the glare of a car:- https://brainly.com/question/24842661

#SPJ11

Vacuum operated EGR valves are controlled by a pulse width modulated solenoid valve.

This type of valve is responsible for regulating the vacuum pressure that controls the EGR valve. The solenoid valve works by opening and closing a small port that allows vacuum pressure to enter the EGR valve,

which in turn opens or closes the valve as needed. The pulse width modulation aspect of the solenoid valve refers to the way in which the valve is controlled.

It operates by rapidly turning the valve on and off at a very high frequency, which allows for precise control over the amount of vacuum pressure that enters the EGR valve. This allows for optimal engine performance and emissions control.

To learn more about : pulse width

https://brainly.com/question/26058582

#SPJ11

One characteristic that both process fluid and heating/cooling fluid can share is their ability to transfer heat. Both types of fluids are designed to either absorb or release heat in order to maintain a desired temperature.

The process fluid, for example, may be used in an industrial process where it needs to be heated or cooled to a specific temperature to carry out a particular function. In order to achieve this, a heating or cooling fluid is circulated around the process fluid to either increase or decrease its temperature as needed.

Similarly, a heating or cooling fluid may be used in a heating or air conditioning system to maintain a comfortable temperature in a building. In this case, the fluid absorbs heat from the air in the building and releases it outside, or vice versa. Therefore, the ability to transfer heat is a crucial characteristic that both types of fluids share.

You can learn more about fluid at: brainly.com/question/21708739

#SPJ11

The considerations include identifying the target audience, defining goals and objectives, developing a testing plan, ensuring compatibility with different devices and browsers, creating a backup and recovery plan.

When planning the testing, publishing, and maintenance of a website, it is essential to consider several factors to ensure a successful launch and long-term success.

These considerations may include identifying the website's target audience, setting clear goals and objectives, testing the website's

functionality, design, and usability, ensuring compatibility with different browsers and devices, creating a content management plan, implementing security measures, and establishing a plan for regular maintenance and updates.

These steps should be included in the planning process to help identify and address any potential issues early on and to ensure that the website meets the needs of its users while remaining secure and up-to-date.

Learn more about considerations

brainly.com/question/15445409

#SPJ11

Mass of Betelgeuse = 32 × 10^30 kg

Volume = 5.24 × 10^44 m³

The average density = 6.1 × 10^(-14) kg/m³

Given that Betelgeuse has 16 times the mass of our Sun, and the Sun's mass is 2 × 10^30 kg, we can find the mass of Betelgeuse by multiplying the Sun's mass by 16:

Mass of Betelgeuse = 16 × (2 × 10^30 kg)

Mass of Betelgeuse = 32 × 10^30 kg

Radius = 500 million km × (1,000,000 m/km)

Radius = 500 × 10^6 km × 1,000,000 m/km

Radius = 500 × 10^6 × 10^6 m

Radius = 5 × 10^8 × 10^6 m

Radius = 5 × 10^14 m

To find the volume of Betelgeuse, we can use the formula for the volume of a sphere:

Volume = (4/3) × π × radius³

Volume = (4/3) × π × (5 × 10^14 m)³

Volume ≈ 5.24 × 10^44 m³

(c) What is the average density of Betelgeuse (in kg/m³)?

Now that we have the mass and the volume of Betelgeuse, we can calculate its average density:

Density = Mass / Volume

Density = (32 × 10^30 kg) / (5.24 × 10^44 m³)

Density ≈ 6.1 × 10^(-14) kg/m³

The average density of Betelgeuse is approximately 6.1 × 10^(-14) kg/m³.

Read more on average density here:https://brainly.com/question/1354972

#SPJ1

For maximum engine power to be obtained, maximum cylinder pressure should occur at the optimal timing during the engine's cycle.

The timing of the maximum pressure can be adjusted by manipulating variables such as fuel injection timing, valve timing, and ignition timing. The goal is to achieve maximum cylinder pressure during the power stroke when the piston is pushing down on the crankshaft with the most force.

This results in a greater torque output and ultimately, greater power. However, it is important to note that excessively high cylinder pressure can lead to engine damage, so finding the optimal balance is crucial.

Therefore, it is important for engine designers and tuners to carefully consider the engine's intended use, performance goals, and durability when optimizing cylinder pressure.

To learn more about : engine power

https://brainly.com/question/30081907

#SPJ11

Crumple zones work together with body rigidity in reducing the force of impact. By absorbing the energy from a collision, crumple zones help to slow down the vehicle gradually, while body rigidity helps to maintain the integrity of the passenger compartment.

The combination of these features reduces the force of impact felt by the passengers, increasing their chances of survival and minimizing the risk of injury, Here's a step-by-step explanation:

1. Crumple zones are strategically designed areas in a vehicle's structure that absorb and redistribute the force of impact during a collision.
2. Body rigidity refers to the stiffness of a vehicle's structure, which helps maintain the overall shape and integrity of the vehicle during an accident.
3. When a collision occurs, the crumple zones deform and absorb the energy from the impact, while the rigid body structure helps protect the passengers by maintaining the vehicle's shape.
4. By working together, crumple zones and body rigidity reduce the force of impact, thereby increasing passenger safety during a collision.

To know more about  rigidity in reducing:- https://brainly.com/question/31171602

#SPJ11

A steel compression member with a fixed support at one end and a frictionless ball joint at the other end, as described, is subject to a specific type of buckling known as Euler's critical buckling.

This buckling phenomenon occurs when the applied load reaches a critical value, causing the member to suddenly buckle and deform. In this case, the total applied design load consists of a 7 kip dead load and an unspecified live load. Since the fixed support provides full restraint, while the frictionless ball joint allows rotational movement, the member experiences one end fixed, and one end pinned boundary conditions. This configuration results in a lower buckling load capacity compared to a member with fixed supports at both ends, making it crucial to consider Euler's critical buckling when designing this compression member.

To know more about frictionless visit:

brainly.com/question/26515803

#SPJ11

The zero-state response of an LTID system can be found by convolving the input signal with the impulse response of the system.

a. The input signal is x[n] = 2"u[n]. The convolution of h[n] and x[n] is:

y[n] = (h × x)[n] = ∑_(k=0)^∞ (0.5)^k 2 δ[n-k]

Since u[n] = 1 for n ≥ 0 and 0 otherwise, the sum above can be simplified to:

y[n] = 2∑_(k=0)ⁿ (0.5)^k

This is a geometric series with a = 1 and r = 0.5, so it can be evaluated as:

y[n] = 2(1 - (0.5)⁽ⁿ⁺¹⁾)

b. The input signal is x[n] = 2n-3u[n]. The convolution of h[n] and x[n] is:

y[n] = (h × x)[n] = ∑_(k=0)^∞ (0.5)^k (2(n-k)-3)u[n-k]

Substituting n-k for n in the expression above and changing the summation index k to j:

y[n] = ∑_(j=-∞)ⁿ (0.5)^(n-j) (2j-3)u[j]

The sum only includes terms where j ≥ 0 because of the unit step function u[j]. Therefore, when n < 0, y[n] = 0. For n ≥ 0, the sum can be evaluated as:

y[n] = 2(1 - (0.5)⁽ⁿ⁺¹⁾) - 3(0.5)ⁿ

c. The input signal is x[n] = 2"u[n-2]. The convolution of h[n] and x[n] is:

y[n] = (h × x)[n] = ∑_(k=0)^∞ (0.5)^k 2 δ[n-2-k] u[n-2-k]

When n < 2, the unit step function u[n-2-k] is 0 for all k, so y[n] = 0. For n ≥ 2, the sum can be simplified to:

y[n] = 2(0.5)⁽ⁿ⁻²⁾ u[n-2] = 2(0.5)⁽ⁿ⁻²⁾ u[n]

Therefore, y[n] = 0 for n < 2 and y[n] = 2(0.5)⁽ⁿ⁻²⁾  for n ≥ 2.

Find out more on LTID system here: https://brainly.com/question/31498685

#SPJ4

All four steps of the IDPE (Identify, Define, Plan, Execute) process have the common goal of helping individuals or organizations achieve their desired outcomes.

They all involve a systematic and intentional approach to problem-solving and goal-setting. The first step, Identify, requires individuals or organizations to assess their current situation and identify areas for improvement or change.

The second step, Define, involves clarifying the specific goals and outcomes they want to achieve. The third step, Plan, requires developing a comprehensive plan with specific strategies and action steps to achieve those goals.

The final step, Execute, involves putting the plan into action and monitoring progress towards the desired outcomes.

Overall, the IDPE process provides a structured framework for achieving success and reaching desired outcomes, whether in personal or professional settings.

To learn more about : IDPE

https://brainly.com/question/29412928

#SPJ11

Technician A is correct in stating that in a COP (coil-on-plug) system, the PCM (powertrain control module) can adjust the ignition timing for each individual cylinder.

This is possible because each cylinder has its own dedicated coil, which eliminates the need for a distributor or shared coil. By controlling the timing of each cylinder's spark plug individually, the engine can run more efficiently and smoothly.

However, Technician B is incorrect in stating that firing order in a COP system is controlled by the IC (ignition control) modules.

In fact, the firing order in a COP system is determined by the engine's design and cannot be changed by the IC modules.

The IC modules are responsible for providing power to the coils and for controlling the timing and duration of the spark, but they do not determine the firing order.

To learn more about : COP

https://brainly.com/question/13441103

#SPJ11

If you accidentally go off the roadway, the most important thing to do is to remain calm and avoid panic. Once you have regained your composure, you can then begin to assess the situation and determine the best course of action.

One braking technique that can be effective in this situation is to use "threshold braking." This technique involves applying the brakes firmly and gradually, in order to slow down the vehicle without locking up the wheels or losing control.

To use threshold braking, apply steady pressure to the brake pedal and gradually increase the pressure until you feel the brakes begin to "bite" or slow down the vehicle. You should also steer the vehicle back onto the roadway, using small, controlled movements of the steering wheel.

It's important to remember that different types of vehicles and road conditions may require different braking techniques, and that the best approach will depend on the specific circumstances of the situation. In general, however, remaining calm and focused, and using gradual and controlled braking, can help to prevent accidents and ensure your safety on the road.

For such more questions on Roadway:

https://brainly.com/question/28963962

#SPJ11

The correct expression while assume that age has been declared as an int variable is 1) ((age < 20) && (age >= 13)). Option 1 is correct.

This expression checks if the age is less than 20 (i.e., the person is not yet in their twenties) and greater than or equal to 13 (i.e., the person is at least 13 years old). This is the standard definition of a teenager, as it includes all individuals between the ages of 13 and 19.

Option 2 is also true for a teenager, but it is not as precise as option 1. Option 3 is always false, as it checks if the age is less than or equal to 19 and also less than 13, which is not possible. Option 4 is true for all ages, as it checks if the age is less than or equal to 19 or greater than or equal to 13.

Option 5 checks if the age is less than or equal to 19 and greater than or equal to 12, which includes some pre-teen ages as well as teenage ages.

Learn more about int variable https://brainly.com/question/28874745

#SPJ11

The equipment being referred to here is the DW21R Recessed Door Contact (Equipment Code: 1252), which is a wireless sensor used for detecting the opening and closing of doors.

This equipment is being added to a wireless zone within the installer toolbox, specifically for loop 1.

The TXID (transmitter ID) and voice descriptor may be programmed to identify the sensor within the system, and the dialer delay option can be turned on or off depending on the specific needs of the installation.

Overall, this equipment is part of a larger system used for monitoring and securing a building or home, and can be customized and configured according to the user's preferences.

Learn more about Equipment Code at

https://brainly.com/question/31846046

#SPJ11

The 74192/74193 up/down counter can be cleared to 0 by applying a clear signal to the appropriate input pin.

In the 74192, the clear signal is applied to pin 1 (Clear), and in the 74193, the clear signal is applied to pin 15 (Clear). When the clear input is activated, the counter is reset to 0, regardless of the current count value or direction.

It's worth noting that the specific clear input signal may vary depending on the implementation of the counter circuit. In some designs, the clear input may be active low (i.e., a logic 0 clears the counter), while in others it may be active high (i.e., a logic 1 clears the counter). It's important to refer to the specific datasheet for the device being used to determine the correct clear input signal.

To know more about input pin,

https://brainly.com/question/14992051

#SPJ11

All steam boilers must have at least one method for determining water level.

Water level is a critical factor in steam boiler operation, as insufficient water can cause overheating and explosion. To ensure safe and efficient operation, all steam boilers are required to have at least one method for determining water level.

This could include a gauge glass, which allows operators to visually inspect the water level, or automated methods such as electronic sensors or probes. In addition to the minimum requirement of one water level determination method, some boilers may have multiple methods for redundancy and safety purposes.

The specific methods used will depend on the type and size of the boiler, as well as the regulations and guidelines applicable in the jurisdiction where it is located.

For more questions like Water click the link below:

https://brainly.com/question/28465561

#SPJ11

In order to answer whether the statement "in the serenitea pot, there is an open-air workshop that can be used for forging" is true or not, I will provide an explanation and conclusion.

The Serenitea Pot is a housing system in Genshin Impact where players can build and decorate their own personal space. It is divided into different realms, each with its own unique environment and features. One of these realms is the Floating Abode, which is described as an idyllic village suspended in the clouds.

Within the Floating Abode, there are various facilities that players can construct, including workshops for crafting and refining materials. However, there is no specific mention of an open-air workshop for forging. It is possible that players may choose to construct such a workshop themselves using the available building materials, but it is not a pre-existing feature of the Floating Abode.

In conclusion, the statement "in the serenitea pot, there is an open-air workshop that can be used for forging" is not entirely accurate. While it is possible for players to create a workshop for forging within their own Serenitea Pot, it is not a pre-existing feature of the Floating Abode realm.

To learn more about workshop, visit:

https://brainly.com/question/31026752?referrer=searchResults

#SPJ11

Passengers are not allowed to ride in a house trailer that is being towed. In most jurisdictions, it is illegal to carry passengers in a house trailer or any other type of trailer while it is being towed.

This is because trailers are not designed or equipped to safely transport people and do not have the necessary safety features, such as seat belts, airbags, or impact-resistant structures. In addition, trailers can be more prone to accidents or rollovers than other types of vehicles, especially if they are overloaded or not properly hitched to the towing vehicle.

To ensure the safety of all passengers, it is important to follow all traffic laws and regulations related to towing and passenger transport. This may include limiting the number of passengers in the towing vehicle, using proper safety equipment such as seat belts and child restraints, and avoiding any unsafe or illegal practices such as carrying passengers in a house trailer.

Learn more about Passengers here:

https://brainly.com/question/199361

#SPJ11

The required rate of return (RRR) is the minimum rate of return that an investor expects to receive from an investment project in order to justify the risk of investing in it.

The RRR is determined by several factors, such as the level of risk associated with the investment, the cost of capital, inflation, and the time horizon of the investment. In general, riskier investments require a higher RRR, while less risky investments may require a lower RRR.

Investors use the RRR as a benchmark to evaluate investment opportunities and decide whether or not to invest in a particular project. If the expected rate of return of a project is less than the RRR, the investor will likely reject the project as it does not meet their minimum acceptable rate of return.

To know more about required rate of return,

https://brainly.com/question/29511106

#SPJ11

The tool that uses white space to conceal data payloads in the context of your question is sno. Option D is correct.

Snow is a steganography tool that can hide data within the white space of a text file using the ASCII format. It is a command-line tool that is commonly used to hide messages in plain sight by altering the least significant bits of the text file's white space.

Steghide is a freely available tool that allows users to conceal a payload within either an audio or image file. It has the capability to compress, encrypt, and hide data.

OpenStego works like other similar tools, allowing users to embed a message within a carrier file. To use it, you need to ensure that you have the Java Runtime Environment (JRE) installed.

Yersinia uses packet crafting techniques as part of its attack strategy. Other popular packet crafting tools include Scapy or hping3, which enable users to create their own packets.

Therefore, option D is correct.

Learn more about data payloads https://brainly.com/question/30243533

#SPJ11

The front passenger door module is a slave module which can communicate with the master module, also known as the main control module.

It operates through a network of sensors and actuators that allow it to perform various functions such as controlling the window, mirror, lock, and speaker systems of the vehicle.

As a slave module, it receives commands from the master module and executes them accordingly. It can also send feedback to the master module about the status of the various systems it controls.

This communication between the slave and master modules ensures that the various systems of the vehicle are working in unison, providing the driver and passengers with a seamless and comfortable experience.

To learn more about : module

https://brainly.com/question/30482795

#SPJ11

The flow rate for streams is called the discharge (option D).

Discharge refers to the volume of water passing through a specific point in the stream within a given period of time, usually measured in cubic meters per second (m³/s) or cubic feet per second (cfs). Discharge is an important parameter for understanding the movement of water in a stream and is influenced by factors such as rainfall, snowmelt, and landscape features.

The other options mentioned are not directly related to the flow rate of streams. Capacity (option A) refers to the maximum amount of water a stream can hold before flooding occurs. Competence (option B) is a measure of the largest particle size a stream can transport, which is influenced by the stream's velocity and discharge. Area (option C) typically refers to the size of the watershed that contributes water to the stream or the cross-sectional area of the stream channel itself.

In summary, the correct answer for the flow rate of streams is discharge (option D), as it represents the volume of water flowing through the stream within a specific time frame.

Learn more about Discharge here: https://brainly.com/question/29802656

#SPJ11