in
Polymer Flooding.
in Polymer Flooding
PART B: TERTIARY DRIVE MECHANISM (16 marks) 1. Describe the theory and mechanisms of the tertiary recovery technique selected for your group. [6 marks]

Answers

Answer 1

Polymer flooding is a tertiary recovery technique used in the oil and gas industry to enhance oil recovery from reservoirs.The mechanisms of polymer flooding involve:

Mobility ControViscous Fingering ReductionSweep ImprovementOil Viscosity ReductionAdsorption and Shear-Thinning Behavior

By injecting a polymer solution into the reservoir, more oil is swept toward the production wells, and the displacement efficiency of the injected fluid is increased. The theory and mechanisms of polymer flooding can be described as follows:

Mobility Control: Mobility control is one of the main processes of polymer flooding. High-molecular-weight compounds called polymers can make the water being injected viscous. The mobility ratio between the injected fluid and the reservoir oil is changed by injecting a polymer solution. As a result of the polymer solution's higher viscosity, which lowers water's mobility and permits more uniform movement throughout the reservoir, more oil is swept toward production wells.Viscous Fingering Reduction: Viscous fingering is a phenomenon that happens when a low-viscosity fluid, like water, passes unevenly through a high-viscosity fluid, like oil. This may result in channeling when water preferentially uses particular passageways and largely avoids other parts of the reservoir. By introducing polymers, the fluid's viscosity is enhanced, reducing the effects of viscous fingering and encouraging more evenly distributed oil displacement.Sweep Improvement: Additionally, polymers can increase the fluid injection's sweep efficiency. The injection of water into an oil reservoir often results in pockets of oil being left behind as the water takes the path of least resistance. Polymers' higher viscosity aids in displacing oil from these unswept zones, boosting the sweep's overall efficiency and the amount of oil recovered.Oil Viscosity Reduction: Polymers occasionally interact with reservoir oil to lessen their viscosity. This might happen by means of processes including expansion of the oil phase, polymer-oil mixing, or a decrease in the interfacial tension between the oil and the water. Oil's viscosity can be decreased to make it simpler to remove and recover from reservoirs.Adsorption and Shear-Thinning Behavior: Since polymers have the propensity to adhere to rock surfaces, they can change the wettability of the rock and improve oil recovery. Additionally, some polymers display shear-thinning behavior, which means that as the shear rate increases, their viscosity drops. Easy injection via the reservoir and improved conformity control are made possible by this behavior.

Therefore, Polymer flooding is a tertiary recovery technique used in the oil and gas industry to enhance oil recovery from reservoirs. The mechanisms of polymer flooding involve:

Mobility ControViscous Fingering ReductionSweep ImprovementOil Viscosity ReductionAdsorption and Shear-Thinning Behavior

To know more about polymers, click here:

https://brainly.com/question/30722610

#SPJ4


Related Questions

Answer the following question after observing the given diagram.
(a) Ehich type of simple machije is it?
(b) Find the velocity ratio , mechanical advantage and efficiency of the machine?

Answers

(a) The type of simple machine given in image is wheel and axle.

(b.i) The velocity ratio of the machine is 5.

(b.ii) The mechanical advantage of the machine is  4.

(b.iii) The efficiency of the simple machine is 80%.

What type of simple machine is in the image?

(a) The type of simple machine given in image is know as the wheel and axle, as we can see the wheel with bigger and axle with smaller radius.

(b.i) The velocity ratio of the machine is calculated by applying the following formula;

V.R = R/r

V.R = 20 cm / 4 cm

V.R = 5

(b.ii) The mechanical advantage of the machine is calculated as follows;

M.A = Load / Effort

M.A = 200 N / 50 N

M.A = 4

(b.iii) The efficiency of the simple machine is calculated as follows;

E = M.A / V.R x 100%

E = 4 / 5  x 100%

E = 80%

Learn more about mechanical advantage here: https://brainly.com/question/25984831

#SPJ1

suppose you are riding a stationary exercise bicycle, and the electronic meter indicates that the wheel is rotating at 9.1 rad/s. the wheel has a radius of 0.45 m. if you ride the bike for 35 min, how far would you have gone if the bike could move?

Answers

If the bike could move, you would have traveled approximately 8671.5 meters (or 8.6715 kilometers) during the 35-minute ride.

To determine the distance you would have traveled on the stationary exercise bicycle, we need to calculate the linear distance covered by the edge of the wheel over the given time period.

The linear distance covered by the edge of the wheel can be calculated using the formula:

Distance = Angular Speed * Radius * Time

Given:

Angular Speed = 9.1 rad/s

Radius = 0.45 m

Time = 35 min = 35 * 60 s (converting minutes to seconds)

Substituting the values into the formula, we have:

Distance = 9.1 rad/s * 0.45 m * (35 * 60 s)

Calculating the result:

Distance ≈ 9.1 * 0.45 * 35 * 60 ≈ 8671.5 m

Therefore, if the bike could move, you would have traveled approximately 8671.5 meters (or 8.6715 kilometers) during the 35-minute ride.

To know more about kilometers here

https://brainly.com/question/13987481

#SPJ4

The following table was given to Candoe by her teacher. She couldn't find answer to some questions. Help her in completing the table.
Layer name Horizon name

1. Organic layer 1. Horizon O

2. Top soil 2. Horizon A

3. Sub soil 3. Horizon B

4. Weathered rock particles 4. Horizon C

5. Bed rock 5. Horizon R

Answers

Here is the completed soil horizon table:

Layer name Horizon name

Organic layer 1. Horizon O

Top soil 2. Horizon A

Sub soil 3. Horizon B

4.Weathered rock particles 4. Horizon C

Bed rock 5. Horizon R

The soil horizon names are:

O horizon: This is the organic layer consisting of accumulating plant litter and decomposing organic matter.

A horizon: This is the top soil consisting of mineral material mixed with organic matter. It has the highest concentration of organic matter.

B horizon: This is the subsoil consisting of predominantly mineral material. It has less organic matter than the A horizon.

C horizon: This consists of weathered bedrock with accumulated mineral material. It contains few organic materials.

R horizon: This is the unweathered bedrock material beneath the soil layers.

So each soil layer is named according to its composition and properties using horizon names from O to R

The work W done by a constant force F in moving an object from a point A in space to a point B in space is defined as W=F⋅AB. Find the work done by a force of 3 newtons acting in the direction −2i−2j−k in moving an object 4 meters from (0,0,0) to (0,4,0) W=

Answers

Let's consider the vector AB, which is the displacement vector from point A(0, 0, 0) to point B(0, 4, 0). The vector AB is as follows:AB = (0 - 0)i + (4 - 0)j + (0 - 0)k = 4jWe know that force F = 3N is acting in the direction of the vector -2i - 2j - k.

So, the direction cosines of force F are given by:cosα = -2/3cosβ = -2/3cosγ = -1/3The work W done by force F in moving an object from point A to point B is given by the dot product of F and AB. Therefore:W = F ⋅ AB = |F||AB| cosθwhere θ is the angle between F and AB.

Since force F and vector AB are perpendicular, θ = 90° and cosθ = 0.So, W = |F||AB| cosθ = 0Therefore, the work done by a force of 3 newtons acting in the direction −2i−2j−k in moving an object 4 meters from (0,0,0) to (0,4,0) is 0. Answer: W = 0.

To know more about displacement  visit:-

https://brainly.com/question/11934397

#SPJ11

How many neutrons are in K-41? Express your answr as an integer

Answers

The number of neutrons in K-41 (isotope of potassium)in the form of an integer is 21.

The isotope K-41, which represents potassium-41, has 20 protons (as indicated by the atomic number of potassium) since the number of protons defines the element. To determine the number of neutrons, we subtract the atomic number from the mass number. The mass number of potassium-41 is approximately 41. Therefore, to find the number of neutrons, we subtract 20 (protons) from 41 (mass number):

Number of neutrons = Mass number - Atomic number

= 41 - 20

= 21 (number of neutrons)

Hence, there are 21 neutrons in the K-41 isotope of potassium.

To learn more about neutrons, click here;

https://brainly.com/question/31977312

#SPJ11

The daily use of electricity (measured in megawatt-hours) in a certain town is a normal random variable with a mean of 18 and a standard deviation of 6 . What is the probability that on a given day, the use of electricity will be between 15.6 and 19.5 megawatt-hours? Refer to the information in Problem 1. When the daily use of electricity exceeds the capacity of the power plant, a blackout occurs. If we know that the probability of a blackout is 0.33, what is the capacity of the power plant?
Previous question

Answers

The probability of the electricity use being between 15.6 and 19.5 megawatt-hours is approximately 0.2541, and the capacity of the power plant is approximately 15.42 megawatt-hours.

To find the probability of the electricity use being between 15.6 and 19.5 megawatt-hours, we need to standardize the values using the z-score formula.

Z₁ = (15.6 - 18) / 6 ≈ -0.4

Z₂ = (19.5 - 18) / 6 ≈ 0.25

Next, we can use a standard normal distribution table or calculator to find the probabilities associated with these z-scores.

The probability corresponding to Z₁ is P(Z ≤ -0.4) ≈ 0.3446.

The probability corresponding to Z₂ is P(Z ≤ 0.25) ≈ 0.5987.

To find the probability of the electricity use being between 15.6 and 19.5 megawatt-hours, we subtract the probability associated with Z₁ from the probability associated with Z₂:

P(15.6 ≤ X ≤ 19.5) ≈ 0.5987 - 0.3446 ≈ 0.2541.

Therefore, the probability that the use of electricity will be between 15.6 and 19.5 megawatt-hours is approximately 0.2541.

In Problem 2, if the probability of a blackout is 0.33, we can set up the equation:

0.33 = 1 - P(X ≤ C)

Since the blackout occurs when the electricity use exceeds the capacity of the power plant, we need to find the value of C that corresponds to the probability of 0.33 in the standard normal distribution.

Using a standard normal distribution table or calculator, we can find the z-score corresponding to a probability of 0.33, which is approximately -0.43.

To find the capacity of the power plant, we can solve for C using the z-score formula:

-0.43 = (C - 18) / 6

Solving for C:

C - 18 = -0.43 × 6

C - 18 ≈ -2.58

C ≈ 18 - 2.58 ≈ 15.42

Therefore, the capacity of the power plant is approximately 15.42 megawatt-hours.

Learn more about the capacity at

https://brainly.com/question/15631063

#SPJ4

A stock analyst plots the price per share of a certain common stock as a function of time and finds that it can be approximated by the function S(t)=29+12e −0.03t
, where t is the time (in years) since the stock was purchased Find the average price of the stock over the first six years. The average price of the stock is $ (Round to the nearest cent as needed.)

Answers

The average price of the stock over the first six years is approximately $42.61.

To find the average price of the stock over the first six years, we need to calculate the average value of the function S(t) = 29 + 12[tex]e^{-0.03t}[/tex]over the interval t = 0 to t = 6.

The average value of function f(x) over the interval [a, b] will given by;

Average value = (1 / (b - a) × ∫[a to b] f(x) dx

In this case, the function is S(t) = 29 + 12[tex]e^{-0.03t}[/tex], and we want to find the average value over the interval t = 0 to t = 6.

Average price = (1 / (6 - 0) × ∫[0 to 6] (29 + 12[tex]e^{-0.03t}[/tex] dt

Let's calculate the integral;

∫(29 + 12[tex]e^{-0.03t}[/tex] dt = 29t - (12 / 0.03)[tex]e^{-0.03t}[/tex]

Now, we substitute the limits of integration;

Average price = (1 / 6) × [(29 × 6 - (12 / 0.03)[tex]e^{-0.03X6}[/tex] - (29 × 0 - (12 / 0.03)[tex]e^{-0.03X0}[/tex]]

Simplifying further;

Average price = (1 / 6) × [(174 - (12 / 0.03) [tex]e^{-0.18}[/tex] - (0 - (12 / 0.03)e⁰]

Since e⁰ = 1;

Average price = (1 / 6) × [(174 - (12 / 0.03)[tex]e^{-0.18}[/tex] - 0]

Average price = (1 / 6) × (174 - (12 / 0.03)[tex]e^{0.18}[/tex]

Now we calculate the average price by substituting the given values:

Average price = (1 / 6) × (174 - (12 / 0.03)[tex]e^{-0.18}[/tex]

≈ $42.61 (rounded to the nearest cent)

Therefore, the average price of the stock over the first six years is approximately $42.61.

To know more about average price here

https://brainly.com/question/30362787

#SPJ4

an electron moves with a speed of what are the magnitude and direction of the magnetic force on the electron

Answers

To determine the magnitude and direction of the magnetic force on an electron moving with a certain speed, we need additional information, specifically the strength and direction of the magnetic field in which the electron is moving. The magnetic force experienced by a charged particle depends on the velocity of the particle, the magnetic field strength, and the angle between the velocity vector and the magnetic field vector.

If we have the value and direction of the magnetic field, we can use the formula for the magnetic force on a charged particle:

F = q * v * B * sin(theta)

Where:

F is the magnitude of the magnetic force

q is the charge of the electron

v is the velocity of the electron

B is the magnetic field strength

theta is the angle between the velocity vector and the magnetic field vector

If you provide the necessary information, such as the magnetic field strength and its direction, we can calculate the magnitude and direction of the magnetic force on the electron.

To learn more about magnitude , Click here: brainly.com/question/31022175?

#SPJ11

three resistors are connected in series across a 13-v power supply. if the potential drops across resistors 1 and 2 are 3.3 volts and 4.8 volts, what is the exact potential drop (in volts) across resistor 3? (reminder: never include units with any submission to a numerical question.)

Answers

A 13-v power supply is used to power three resistors in series. If there are potential decreases of 3.3 and 4.8 volts across resistors 1 and 2, respectively, Therefore, the exact potential drop across resistor 3 is 5.9 volts.

The sum of the individual voltage drops determines the total voltage across the resistors in a series circuit. We can determine the potential drop across resistor 3 if we know that the potential dips across resistors 1 and 2 are 3.3 volts and 4.8 volts, respectively.

We'll refer to the voltage drop across resistor 3 as V3. We may build up the following equation because the total voltage across the resistors is 13 volts:

V1 + V2 + V3 = 13

Substituting the known values:

3.3 + 4.8 + V3 = 13

Combining like terms:

V3 = 13 - 3.3 - 4.8

V3 = 5.9 volts

Therefore, the exact potential drop across resistor 3 is 5.9 volts.

To know  more about resistor

https://brainly.com/question/24179042

#SPJ4

A 8.64 kVA, 480/360 V transformer has the following parameters: primary resistance = 0.03 ohm primary reactance = 0.092 ohm Equivalent core loss resistance = 1688 ohm Magnetizing reactance = 256 ohm Secondary resistance = 0.75 ohm Secondary reactance = 2.5 ohm The transformer is supplying full load at unity power factor. Using the exact equivalent circuit, calculate the magnitude of the induced voltage in volt at the secondary side. NB: the secondary voltage is fixed at 360 V

Answers

The transformer is supplying full load at unity power factor. Using the exact equivalent circuit, calculate the magnitude of the induced voltage in volt at the secondary side the magnitude of the induced voltage at the secondary side of the transformer is |Vc| = |480 - 0.78I|.

To calculate the magnitude of the induced voltage at the secondary side of the transformer using the exact equivalent circuit, we need to consider the voltage drop across the primary resistance, primary reactance, and the secondary resistance.

Given data:

Primary resistance (Rp) = 0.03 ohm

Primary reactance (Xp) = 0.092 ohm

Equivalent core loss resistance (Rc) = 1688 ohm

Magnetizing reactance (Xm) = 256 ohm

Secondary resistance (Rs) = 0.75 ohm

Secondary reactance (Xs) = 2.5 ohm

Secondary voltage (Vs) = 360 V

Using the exact equivalent circuit, we can apply the following equations for the primary and secondary voltages:

Vp = Vc + (Ic * Rp) + (Ic * jXp) + (Is * Rs) + (Is * jXs)

Vs = Vp - (Is * Rs) - (Is * jXs)

Since the transformer is supplying full load at unity power factor, the current on the primary and secondary sides will be the same, denoted as I. Therefore, we can simplify the equations:

Vp = Vc + (I * Rp) + (I * jXp) + (I * Rs) + (I * jXs)

Vs = Vp - (I * Rs) - (I * jXs)

Now, let's substitute the given values into the equations and solve for the magnitude of the induced voltage (Vc):

Vp = 480 V (primary voltage)

Vc = Vp - (I * Rp) - (I * jXp) - (I * Rs) - (I * jXs)

Vs = 360 V (secondary voltage)

Substituting the values into the equation for Vc:

Vc = 480 - (I * 0.03) - (I * j * 0.092) - (I * 0.75) - (I * j * 2.5)

Since Vc is the induced voltage, we want to solve for its magnitude. Taking the magnitude of Vc:

|Vc| = |480 - (I * 0.03) - (I * j * 0.092) - (I * 0.75) - (I * j * 2.5)|

Simplifying the equation:

|Vc| = |480 - (0.03 + j * 0.092 + 0.75 + j * 2.5) * I|

Now, we need to solve for the magnitude of the expression inside the absolute value brackets:

|480 - (0.03 + j * 0.092 + 0.75 + j * 2.5) * I|

Substituting the given values into the equation:

|Vc| = |480 - (0.03 + j * 0.092 + 0.75 + j * 2.5) * I|

= |480 - (0.03 - 0.092j + 0.75 - 2.5j) * I|

Simplifying further:

|Vc| = |480 - (0.78 - 2.592j) * I|

= |480 - 0.78I + 2.592jI|

Since we are interested in the magnitude, we can disregard the phase term. Therefore, we have:

|Vc| = |480 - 0.78I|

Hence, the magnitude of the induced voltage at the secondary side of the transformer is |Vc| = |480 - 0.78I|.

To know more about induced refer here:

https://brainly.com/question/9965450#

#SPJ11

Which rock type is formed from the same aspects that form fossil fuels?

Answers

Answer:

The answer is organic sedimentary rock.

Explanation:

In a windmill, the blades spin due to the energy from the wind. The wind is caused by
differences in temperature. Grain is crushed into powder form by the rolling wheel in the
windmill. All of these examples illustrate what kind of energy?

Answers

The examples given in the question illustrate kinetic energy. Kinetic energy is the energy possessed by an object in motion. When the blades of a windmill spin, it is because they are being driven by the energy of the wind, which is a form of kinetic energy.

Wind turbines and windmills work similarly, but wind turbines have a much more significant generating capacity and require a more complex and sophisticated system to operate. When the wind strikes the turbine blades, it causes them to rotate, converting the kinetic energy of the wind into mechanical energy that can then be harnessed to produce electricity.The wind possesses kinetic energy because it is in motion. This kinetic energy can be harnessed and transformed into other forms of energy, such as mechanical energy, which is what happens in a windmill. The blades of the windmill spin due to the kinetic energy of the wind, which causes the shaft and rotor to rotate. The rotational motion of the rotor is then transmitted to a generator, which produces electricity.Kinetic energy is a type of energy that is possessed by an object in motion. It is different from potential energy, which is the energy stored in an object due to its position or state. In the case of a windmill, the kinetic energy of the wind is harnessed to produce electricity, which can be used for a variety of purposes.

For such more question on Kinetic energy

https://brainly.com/question/8101588

#SPJ8

Will these magnets attract or repel and why ?
A.Repel because they are
PPOSITES
B.Repel because they are
ALIKE
C.Attract because they are
A LIKE
Attract because they are
OPPOSITES
Pls review the picture

Answers

B
opposites attract and likes repel

Identify the parts of a vector.

Please help. I'm unable to comprehend vector operations.​

Answers

The magnitude, direction, components, origin, and terminal points are the key parts of a vector.

How do we calculate?

A vector is known to have  several components that define its properties and characteristics.

The magnitude or length of a vector represents its size or magnitude and  is a scalar quantity that specifies the distance or amount of the vector.

The direction of a vector represents the orientation or angle at which the vector is pointing and indicates the line along which the vector is directed in most cases can be described using angles, unit vectors, or in relation to a coordinate system.

Learn more about a vector at:

https://brainly.com/question/25705666

#SPJ1

Please kindly solve parts A,B,C,D for a thumbs up and positive rating., Thanks
Medical Imaging
A) True/False) When a polyenergetic x-ray beam passes through the patient, x-rays having lower energy are attenuated less than the higher energy x-rays,
and thus those x-rays have better ability to distinguish different tissues.
Restate if False.
B) (True/False) In MRI Fourier space, line spacing and matrix size are proportional to field of view FOV_x x FOV_y, additionally, matrix size determines resolution.
Restate if False.
C) What is a free induction decay (FID)?
a- Destruction of the net magnetisation vector without loss of energy to the
environment ("free").
b- The oscillating decaying MRI signal in the transverse plane.
c- The process by which spins are excited by an RF pulse.
D) Describe the usual shape of RF pulses used (signal shape in the time domain),
and explain why this shape is used.

Answers

A) The statement "When a polyenergetic x-ray beam passes through the patient, x-rays having lower energy are attenuated more than the higher energy x-rays. " is False.

This is due to the higher probability of interaction (e.g., absorption or scattering) of lower-energy x-rays with the patient's tissues. Therefore, higher-energy x-rays are more useful for distinguishing different tissues because they undergo greater attenuation.

B) The given statement "In MRI Fourier space, the line spacing and matrix size are indeed proportional to the field of view (FOV) in each direction (FOV_x and FOV_y)" is True.

The FOV determines the spatial extent of the image. Additionally, the matrix size determines the resolution of the image. A larger matrix size provides higher spatial resolution by dividing the FOV into more pixels.

C) The Free Induction Decay (FID) is the oscillating decaying MRI signal in the transverse plane.The correct option is b.

The Free Induction Decay (FID) is the initial signal obtained after the excitation of spins by an RF pulse in MRI. It is a decaying oscillating signal that occurs in the transverse plane and contains information about the magnetic properties of the tissue.

D) The usual shape of RF pulses used in MRI is a sinc-shaped pulse in the time domain. The sinc function has a central lobe with smaller side lobes. This shape is used because it provides a wide range of frequencies necessary for exciting spins over a desired bandwidth. The main lobe of the sinc function ensures uniform excitation across the imaging volume, while the smaller side lobes help in minimizing unwanted artifacts and interference.

To know more about polyenergetic x-ray  refer here

https://brainly.com/question/15202716#

#SPJ11

a car travels 95 km to the north at 70.0 km/h, then turns around and travels 21.9 km at 80.0 km/h. what is the difference between the average speed and the average velocity on this trip? question 1 options: a) 24 km/h b) 32 km/h c) 19 km/h d) 27 km/h

Answers

The difference between the average speed and the average velocity on this trip is approximately 27 km/h.

Hence, the correct option is D.

To find the difference between the average speed and the average velocity on this trip, we first need to calculate the average speed and the average velocity separately.

Average speed is calculated by dividing the total distance traveled by the total time taken. In this case, the total distance traveled is the sum of the distances traveled in each leg of the trip (north and south), and the total time taken is the sum of the times taken for each leg.

Total distance = 95 km (north) + 21.9 km (south) = 116.9 km

Total time = (95 km / 70 km/h) + (21.9 km / 80 km/h) = 1.357 h + 0.274 h = 1.631 h

Average speed = Total distance / Total time = 116.9 km / 1.631 h ≈ 71.68 km/h

Average velocity, on the other hand, takes into account both the magnitude and direction of motion. Since the car travels north and then south, the average velocity will depend on the displacement.

Displacement = 95 km (north) - 21.9 km (south) = 73.1 km (north)

Total time is the same as before, 1.631 h.

Average velocity = Displacement / Total time = 73.1 km / 1.631 h ≈ 44.81 km/h (north)

The difference between the average speed and the average velocity is:

|Average speed - Average velocity| = |71.68 km/h - 44.81 km/h| ≈ 27 km/h

Therefore, the difference between the average speed and the average velocity on this trip is approximately 26.87 km/h.

Hence, the correct option is D.

To know more about average speed here

https://brainly.com/question/13318003

#SPJ4

Calculate the force between a +6 µC test point charge and a source charge of +3.0 × 10^-5 C at a distance of 3.00 cm. (µC = 1.0 × 10–6 C)

Answers

The force between the test point charge and the source charge is 54 N.

To calculate the force between the +6 µC test point charge and the +3.0 × [tex]10^-^5[/tex]C source charge at a distance of 3.00 cm, we can use Coulomb's Law. Coulomb's Law states that the force between two charged objects is proportional to the product of their charges and inversely proportional to the square of the distance between them.

The formula for Coulomb's Law is:

[tex]\[ F = \frac{{k \cdot q_1 \cdot q_2}}{{r^2}} \][/tex]

Where:

- F is the force between the charges,

- k is the electrostatic constant (approximately 9 ×[tex]10^9 Nm^2/C^2[/tex]),

- q1 and q2 are the charges of the test point charge and the source charge, respectively,

- r is the distance between the charges.

Given:

- q1 (test charge) = +6 µC = 6 ×[tex]10^-^6[/tex] C

- q2 (source charge) = +3.0 × [tex]10^-^5[/tex] C

- r = 3.00 cm = 3.00 × [tex]10^-^2[/tex] m

Plugging the values into the formula:

[tex]\[ F = \frac{{(9 × 10^9 \, \text{N}·\text{m}^2/\text{C}^2) \cdot (6 × 10^{-6} \, \text{C}) \cdot (3.0 × 10^{-5} \, \text{C})}}{{(3.00 × 10^{-2} \, \text{m})^2}} \][/tex]

Simplifying the equation:

[tex]\[ F = \frac{{(9 × 6 × 3) \cdot (10^{-6} \cdot 10^{-5})}}{{(3.00)^2}} \cdot 10^9 \, \text{N} \][/tex]

[tex]\[ F = 54 \, \text{N} \][/tex]

Therefore, the force between the +6 µC test point charge and the +3.0 × [tex]10^-^5[/tex] C source charge at a distance of 3.00 cm is 54 N.

For more such information on: force

https://brainly.com/question/12785175

#SPJ8

A 5 kg package is thrown into an initially stationary 25 kg cart. Before the collision, the package has a speed of 2.0 m/s. What is the speed of the system after the collision? Answer: ______ m/s

Answers

To find the speed of the system after the collision between the 5 kg package and the initially stationary 25 kg cart, we can apply the principle of conservation of momentum. According to this principle, the total momentum before the collision should be equal to the total momentum after the collision.

Before the collision, the package has a momentum of 5 kg * 2.0 m/s = 10 kg·m/s (taking the direction into account). Since the cart is initially stationary, its momentum is zero.

After the collision, the package and the cart move together as a system. Let's assume the speed of the system after the collision is v m/s. The total momentum of the system after the collision is then (5 kg + 25 kg) * v [tex]kg·m/s[/tex].

Setting the initial momentum equal to the final momentum, we have:

[tex]10 kg·m/s = (30 kg) * v kg·m/s[/tex]

Solving for v, we find:

[tex]v = 10 kg·m/s / 30 kg = 0.33 m/s[/tex]

Therefore, the speed of the system after the collision is 0.33 m/s.

To learn more about collision click here

brainly.com/question/30636941

#SPJ11

Choose the correct statement(s) concerning charge carrier Mobility: (i) With increasing temperature, the mobility will reduce. (ii) Under an applied electric field, the mobility is constant. (iii) Mobility can be influenced by scattering events. (iv) In an intrinsic semiconductor, the mobility of electrons in the conduction band is the mobility of holes in the valence band. Mobility is dependent on the drift velocity and the diffusion speed of charge carriers.

Answers

The statement(s) concerning charge carrier Mobility are:

(iii) Mobility can be influenced by scattering events.

(iv) In an intrinsic semiconductor, the mobility of electrons in the conduction band is the mobility of holes in the valence band. Mobility is dependent on the drift velocity and the diffusion speed of charge carriers. The correct options are (iii) & (iv).

The mobility of charge carriers refers to their ability to move through a material under the influence of an electric field. Scattering events, such as collisions with impurities, defects, or lattice vibrations, can affect the mobility of charge carriers.

This is why statement (iii) is correct. In an intrinsic semiconductor, the mobility of electrons in the conduction band is equal to the mobility of holes in the valence band, which is stated in (iv).

However, statement (i) is incorrect because with increasing temperature, lattice vibrations increase, leading to more scattering events and a decrease in mobility. Statement (ii) is also incorrect because mobility can change under an applied electric field due to various factors like scattering and temperature.

To know more about carrier Mobility refer here

https://brainly.com/question/30781709#

#SPJ11

A 2 pole, 50 Hz induction motor supplies 30 kW of power to an external load at a speed of 2950 rpm. Calculate the induced torque (in N-m). Consider any reasonable assumptions, if needed; however, if so, state your assumptions clearly.

Answers

The induced torque of the motor is approximately 309.59 N-m.

calculate the induced torque of the induction motor, we can use the following formula:

Torque (τ) = (Power (P) * 60) / (2π * Speed (N))

Power (P) = 30 kW

Speed (N) = 2950 rpm

We assume that the motor operates at its synchronous speed, which is the speed at which the motor's rotor rotates when the number of poles and the frequency of the power supply are known.

for a 2-pole motor and a 50 Hz power supply, the synchronous speed would be 3000 rpm.

Now we can substitute the given values into the formula to calculate the induced torque:

τ = (30,000 * 60) / (2π * 2950) ≈ 309.59 N-m

To know more about induced torque refer here

https://brainly.com/question/32233403#

#SPJ11

Four waves are produced when a harp is strummed at four different times.
Which wave will produce the highest pitch?
A. Wave 1
B. Wave 2
C. Wave 3
D. Wave 4

Answers

Letter C is the correct answer

Sketch the energy band diagrams and output characteristics of a
Schottky contact and Ohmic contact under reverse bias and explain
the carrier movement at the junction.

Answers

Schottky contact under reverse bias: Energy band diagram shows a potential barrier, resulting in a small reverse current due to minority carrier movement.

Ohmic contact under reverse bias: Energy band diagram shows a continuous band without a significant barrier, leading to higher reverse current facilitated by minority carrier movement.

Schottky Contact:

- Energy Band Diagram: In a Schottky contact under reverse bias, the metal electrode (n-type) forms a barrier with the semiconductor (p-type). The energy band diagram shows a potential barrier formed at the metal-semiconductor interface, with the conduction band of the semiconductor bending downwards and the valence band bending upwards near the interface.

- Carrier Movement: In reverse bias, the negatively biased metal electrode repels majority carriers (electrons in n-type semiconductor) from the metal into the semiconductor, creating a depletion region near the interface. The minority carriers (holes in p-type semiconductor) can still move across the barrier, resulting in a small reverse current.

Ohmic Contact:

- Energy Band Diagram: In an Ohmic contact under reverse bias, there is a low-resistance electrical connection between the metal electrode and the semiconductor. The energy band diagram shows a continuous energy band across the metal-semiconductor interface without a significant potential barrier.

- Carrier Movement: In reverse bias, the applied voltage provides an additional driving force for minority carriers (holes in p-type semiconductor) to move towards the metal electrode. The reverse current in an Ohmic contact is significantly higher compared to a Schottky contact due to the absence of a potential barrier.

Note: The sketch of the energy band diagrams and output characteristics may vary depending on the specific semiconductor material and contact configuration.

To know more about Schottky contact refer here

https://brainly.com/question/16258382#

#SPJ11

A Bernoulli random variable has a distribution with 0 = 0.73. Find the mean and variance for the distribution. Mean: 10. A random variable X has a binomial distribution with 0 = 0.34 and a sample size of n. Find the mean and variance for the random variable Y which is defined below. Y =nX Variance: Mean: Variance:

Answers

The mean and variance for a Bernoulli random variable with p = 0.73 are 0.73 and 0.1971, respectively.

The values and calculate the mean and variance for the given distributions:

For the Bernoulli distribution:

The parameter p (probability of success) is given as 0.73.

The mean (μ) of the distribution is equal to p.

Mean (μ) = p = 0.73

To find the variance (σ²), we can use the formula: σ² = p(1 - p).

Variance (σ²) = 0.73(1 - 0.73) = 0.73 × 0.27 = 0.1971

For the binomial distribution with parameter p = 0.34 and sample size n:

The mean (μ) of the binomial distribution is given by μ = np.

Mean (μ) of X = np = n × 0.34

The variance (σ²) of the binomial distribution is given by σ² = np(1 - p).

Variance (σ²) of X = n × 0.34 × (1 - 0.34)

Now, considering the random variable Y defined as Y = nX:

Mean (μY) = n × Mean of X = n × (n × 0.34)

Variance (σ²Y) = n × Variance of X = n × (n × 0.34 × (1 - 0.34))

Learn more about Bernoulli random variables at

https://brainly.com/question/31825823

#SPJ4

Assume that the maximum aperture of the human eye, D
, is approximately 8mm
and the average wavelength of visible light, , is 5.5 x 10-4mm
.
a. Calculate the diffraction limit of the human eye in visible light.
b. How does the diffraction limit compare with the actual resolution of 1 to2 1 to 2 arcminutes ( 60 to
to 120
arcseconds)?
c. To what do you attribute the difference

Answers

a. The diffraction limit of the human eye in visible light is calculated using the formula θ = 1.22 × (λ / D).

b. The diffraction limit is compared to the actual resolution of 1 to 2 arcminutes (60 to 120 arcseconds).

c. The difference between the diffraction limit and actual resolution is attributed to optical imperfections, aberrations, and limitations of the visual system.

a. To calculate the diffraction limit of the human eye in visible light, we can use the formula:

θ = 1.22 × (λ / D)

Given:

λ = 5.5 × [tex]10^{(-4)[/tex] mm

D = 8 mm

Substituting these values into the formula, we get:

θ = 1.22 × (5.5 x [tex]10^{(-4)[/tex] mm / 8 mm)

Simplifying the expression, we find the diffraction limit of the human eye in visible light.

b. To compare the diffraction limit with the actual resolution of 1 to 2 arcminutes (60 to 120 arcseconds), we convert the diffraction limit calculated in part a to arcminutes or arcseconds and compare the values.

c. The difference between the diffraction limit and the actual resolution can be attributed to factors such as optical imperfections, aberrations, and limitations of the visual system, including the processing capabilities of the brain. These factors affect the actual resolution achievable by the human eye, leading to a difference from the diffraction limit.

Learn more about diffraction limits at

https://brainly.com/question/15081792

#SPJ4

Find something (top, coin) to spin and watch it spin! It’s happening to earth now! List the 3 main orbital changes earth undergoes and their time periods. What does this have to do with climate change? List the 3 cyclical orbital changes and their times associated with Milankovitch
2. List all the EMR in order of wavelength. What forms of EMR from the sun are reaching you right now? How many forms are reaching the Moon right now (from the sun)? Explain the role of ozone in our atmosphere...where it is, how it formed and what is does for life! How does the balance of EMR play a critical role in Climate Change and "The Greenhouse Effect". Explain how CO2 and a Greenhouse balance Infrared Radiation creation and absorption?!
3. List and describe the 4 forms of heat transfer to and on planet earth!?! What does this have to do with "weather". Explain and give examples! Explain how a microwave oven heating a bowl of cold soup covers all forms of heat transfer. Earth and soup. SAME! How long does it take for EMR from University of Delaware to reach…. A. moon B. Jupiter C. closest star (not sun) D. your mother

Answers

Here are the answers to the questions:1. Three main orbital changes that the earth undergoes and their time periods are:A. Precession- every 26,000 years B. Obliquity- every 41,000 years C. Eccentricity- every 100,000 yearsThese changes in the earth's orbit, together, have an impact on the amount of solar radiation that reaches the Earth's surface, which then affects climate change. Three cyclical orbital changes and their times associated with Milankovitch are:A. Eccentricity - every 100,000 yearsB. Obliquity - every 41,000 yearsC. Precession - every 26,000 years2. All EMR in order of wavelength are:- Gamma rays- X-rays- Ultraviolet radiation- Visible light- Infrared radiation- Microwave- Radio wavesForms of EMR from the sun that are reaching right now are UV radiation, visible light, and infrared radiation.

The number of forms of EMR reaching the moon right now is two, UV radiation, and visible light.The ozone layer is present in the stratosphere and is formed through a series of complex chemical reactions. The primary function of the ozone layer is to protect the earth from the harmful effects of UV radiation by absorbing it. The balance of EMR plays a critical role in the greenhouse effect. As the amount of greenhouse gases increases, the amount of energy that is absorbed by the Earth's surface also increases. Carbon dioxide and other greenhouse gases can absorb and emit infrared radiation, which plays a crucial role in climate change.3. The four forms of heat transfer to and on planet earth are:- Conduction- Convection- Radiation- AdvectionThese four forms of heat transfer are responsible for weather on planet Earth.

For example, when the sun heats the ground, it results in conduction, which then results in convection as the air heats up and rises. This can lead to cloud formation and precipitation.4. The time it takes for EMR from the University of Delaware to reach:A. Moon - About 1.28 secondsB. Jupiter - About 33.75 minutesC. Closest star (not the sun) - About 4.37 yearsD. Your mother - This question is not clear, please provide more context.

To know more about Eccentricity visit:-

https://brainly.com/question/31912136

#SPJ11

a pilot flies in a straight path for 1 h 30 min. she then makes a course correction, heading 10 degrees to the right of her original course, and flies 2 h in the new direction. if she maintains a constant speed of 625 mi/h, how far is she from her starting position?

Answers

The pilot's distance is 2175 miles from her starting position after flying straight for 1.5 hours and making a course correction by flying 2 hours at a 10-degree angle.

To solve this problem, we can break it down into two components: the distance traveled in the original straight path and the distance traveled during the course correction.

1. Distance traveled in the original straight path:

Since the pilot flies for 1 hour and 30 minutes, which is equivalent to 1.5 hours, and her speed is 625 mi/h, we can calculate the distance using the formula:

Distance = Speed × Time

= 625 mi/h × 1.5 h

= 937.5 miles

2. Distance traveled during the course correction:

The pilot flies for 2 hours at a constant speed of 625 mi/h. However, she makes a course correction, which means she is not flying directly away from her starting position. To determine the distance traveled in the new direction, we need to find the horizontal component of the distance traveled.

The horizontal component can be calculated using trigonometry. Since the pilot is heading 10 degrees to the right of her original course, the angle between the original course and the new direction is 10 degrees.

Horizontal Distance = Distance × cosine(angle)

= 625 mi/h × 2 h × cos(10°)

To use the cosine function, we need to convert the angle to radians:

10° × π/180 = 0.1745 radians

Horizontal Distance = 625 mi/h × 2 h × cos(0.1745 radians)

= 625 mi/h × 2 h × 0.9848

= 1237.5 miles

Therefore, the total distance from the starting position is the sum of the distance traveled in the original straight path and the horizontal distance traveled during the course correction:

Total Distance = Distance in original path + Horizontal Distance

= 937.5 miles + 1237.5 miles

= 2175 miles

So, the pilot is 2175 miles from her starting position.

To learn more about Distance follow the link:

https://brainly.com/question/13034462

#SPJ4

A. Using USLE calculate the average annual soil loss for a row crop field that has a slope length of 400ft and a uniform slope of 8%. The R-factor is 350 , the K factor is 0.35, the C factor is 0.42, and the P factor is 1 . B. What is the annual soil loss if the field is terraced and reduces the slope length to 200ft ?

Answers

A. Using the Universal Soil Loss Equation the average annual soil loss for the row crop field with a slope length of 400ft and uniform slope of 8% is approximately 103.95 units.

B. For the terraced field with a slope length of 200ft, it is around 80.59 units (units depend on the specific USLE factors used).

A. To calculate the average annual soil loss using the Universal Soil Loss Equation (USLE), we use the formula:

Soil Loss = R × K × LS × C × P

Given:

Slope length (L) = 400 ft

Slope gradient (S) = 8%

R-factor = 350

K-factor = 0.35

C-factor = 0.42

P-factor = 1

First, calculate the LS factor:

LS = [tex](L / 72.6)^{0.5[/tex] × (0.065 + 0.045 × [tex](S/100))^{1.18[/tex]

Substitute the given values:

LS = [tex](400 / 72.6)^{0.5[/tex] × (0.065 + 0.045 × [tex](8/100))^{1.18[/tex]

LS ≈ 1.951 × 1.0203 ≈ 1.991

Now, calculate the soil loss:

Soil Loss = R × K × LS × C × P

Soil Loss = 350 × 0.35 × 1.991 × 0.42 × 1

Soil Loss ≈ 103.95

The average annual soil loss for the row crop field is approximately 103.95 units (units depend on the specific USLE factors used).

B. If the field is terraced and the slope length is reduced to 200 ft, we can simply recalculate the LS factor and substitute it into the soil loss equation.

New LS = [tex](200 / 72.6)^{0.5[/tex] × (0.065 + 0.045 × [tex](8/100))^{1.18[/tex]

New LS ≈ 1.376 × 1.0203 ≈ 1.403

Now, calculate the new soil loss:

Soil Loss = R × K × New LS × C × P

Soil Loss = 350 × 0.35 × 1.403 × 0.42 × 1

Soil Loss ≈ 80.59

The annual soil loss for the terraced field with a slope length of 200 ft is approximately 80.59 units (units depend on the specific USLE factors used).

Learn more about Universal Soil Loss Equation (USLE) at

https://brainly.com/question/31482187

#SPJ4

An eddy current separator is used to separate out non-ferrous metal from other waste. It may be described as a binary separator. The eddy current separator has a feed rate of 1,000 kg/h and is operated so that during any 1 hour, 750 kg exits as output 1 and 250 kg as output 2 . In output 1,650 kg is non-ferrous metal and 100 kg is other waste. In output 2, 25 kg is non-ferrous metal and the remaining 225 kg is other waste. (a) Calculate the recovery of non-ferrous metal in the output stream 1. (b) Calculate the purity of output stream 1. (c) What is the effectiveness of the separator?

Answers

(a) Output stream 1 non-ferrous metal recovery = (650 kg / 675 kg) × 100 = 96.30%. (b) The ratio of non-ferrous metal to total material in output stream 1 determines its purity. Output stream 1 purity is 86.67% (c) The separator's efficacy is the proportion of non-ferrous metal removed from the input stream. Effectiveness is 96.30%.

(a) To calculate the recovery of non-ferrous metal in output stream 1, we need to determine the ratio of output 1 to the input stream's total non-ferrous metal.

Non-ferrous production 1: 650 kg

675 kg of non-ferrous metal in input stream.

Recovery of non-ferrous metal in output stream 1 = (Output 1 / Total Input) × 100

Output stream 1 non-ferrous metal recovery = (650 kg / 675 kg) × 100 = 96.30%.

(b) The ratio of non-ferrous metal to total material in output stream 1 determines its purity.

Output stream 1 purity = (Non-ferrous metal / Total material) × 100.

Output stream 1 purity = (650 kg/750 kg) × 100 = 86.67%

(c) Calculate the separator's efficiency by comparing output 1's non-ferrous metal to the input stream's total.

Separator effectiveness = (Non-ferrous metal in output 1 / Total non-ferrous metal in input stream) × 100.

(650 kg / 675 kg) × 100 = 96.30% separator efficiency.

To know  more about non-ferrous metal

https://brainly.com/question/33588293

#SPJ4

Explain first how we got the three equations then solving using Gauss-seidel method with two iterations 12.4 SPRING-MASS SYSTEMS 335 (a) (b) FIGURE 12.11 A system composed of three masses suspended vertically by a series of springs. (a) The sys- tem before release, that is, prior to extension or compression of the springs. (b) The system after release. Note that the positions of the masses are referenced to local coordinates with origins at their position before release. A(x₂-x₂) A(x₂-x₂) A(x,-x₂) my Ḥ m kx₂-x₂) ₁ (x₂-x₂) (a) mag A(x,-x₂) (b) (c) FIGURE 12.12 Free-body diagrams for the three masses from Fig. 12.11. and c) that can be employed to derive d' m₂ =k(xy-x₂) + m₂g - 24(x₂-x₁) dr² my -=mag-k(xs-x₂) and 2 fell € 000 € M₂ (12.17) (12.18) Equations (12.16), (12.17), and (12.18) form a system of three differential equations with three unknowns. With the appropriate initial conditions, they could be used to solve for the displacements of the masses as a function of time (that is, their oscillations). We will discuss numerical methods for obtaining such solutions in Part Seven. For the pres- ent, we can obtain the displacements that occur when the system eventually comes to rest, that is, to the steady state. To do this, the derivatives in Eqs. (12.16), (12.17), and (12.18) are set to zero to give 3kx₁ 2k.x₂ mig -2k.x₁ + 3kx2 kx3 m₂g kx₂ kx3 - m3g + = |||| =

Answers

The steady-state displacements, you would need to perform additional iterations until the displacements converge to a stable solution. However, this information is not provided in the given context.

The given equations represent a system of three differential equations that describe the motion of a system of three masses connected by springs. Let's break down the equations and then explain how to solve them using the Gauss-Seidel method with two iterations.

The system is composed of three masses, labeled m₁, m₂, and m₃, suspended vertically by a series of springs. The positions of the masses are referenced to their positions before release.

The equations given are:

d²x₁/dt² = (k(x₂ - x₁) - m₁g) / m₁ -- Equation (12.16)

d²x₂/dt² = (k(x₁ - 2x₂ + x₃) - m₂g) / m₂ -- Equation (12.17)

d²x₃/dt² = (k(x₂ - x₃) - m₃g) / m₃ -- Equation (12.18)

These equations describe the acceleration of each mass based on the displacements and the forces acting on them due to the springs and gravity. The displacements x₁, x₂, and x₃ represent the deviations of each mass from their equilibrium positions.

To solve these equations using the Gauss-Seidel method with two iterations, follow these steps:

Start with initial guesses for the displacements x₁, x₂, and x₃.

Substitute these initial values into the right-hand side of each equation.

Solve each equation separately for the corresponding acceleration.

Update the displacements x₁, x₂, and x₃ using the computed accelerations.

Repeat steps 2-4 for two iterations, using the updated values of the displacements in each iteration.

Note that the Gauss-Seidel method is an iterative method that improves the solutions with each iteration. Two iterations may not provide an accurate solution, but it gives an idea of the iterative process.

It's important to note that solving a system of differential equations requires additional information such as initial conditions or boundary conditions. Without this information, it is not possible to obtain specific numerical solutions.

To know more about iterations refer here:

https://brainly.com/question/31197563#

#SPJ11

Energy Efficiency= Useful Energy Output/Total Energy Input x 100 (%) If a power plant uses 100 units of energy to create electricity and the output is 15 units, what is the energy efficiency of the power plant? A. 100% B. 20% C. 15%​

Answers

The energy efficient of the power plant that uses 100 units of energy to create electricity is 15%. Option C is the correct answer.

What is energy efficient?

Energy efficient can be defined as the percentage of energy out of the total input energy.

The energy efficiency of the power plant can be calculated using the formula below.

Energy Efficiency = (Useful Energy Output / Total Energy Input) x 100%

The power plant uses 100 units of energy to create electricity and the output is 15 units.

Hence, the energy efficiency of the power plant is:

Energy Efficiency = (15 / 100) x 100% = 15%

Learn more on energy efficiency on https://brainly.com/question/14280607

#SPJ1

Other Questions
What is the heat needed to raise the temperature of 24.7-kg silver from 14.0 degrees Celsius to 76.0 degrees Celsius? Specific heat capacity of silver is 236 J/(kgC).Answer Choices,3.61 E5 J8.18 E4 J9.32 E4 J5.23 E5 J Kew decided to kick back with a glass of their award winning lemonade. To reward themselves for a lemonade well made, they decide to solve a differential equation! Consider the initial value problem y +2y +2y=h(t),y(0)=0,y (0)=1 where h(t) is the function that is 1 for t 1. Classify the two given samples as independent or dependent. Sample 1: Pre-training weights of 19 people Sample 2: Post-training weights of the same 19 people A) dependent B) independent 2. As part of a marketing experiment, a department store regularly malled discount coupons to 25 of its credit card holders. Their total credit card purchases over the next three months were compared to the credit card purchases over the next three months for 25 credit card holders who were not sent discount coupons. Determine whether the samples are dependent or independent. A) dependent B) independent a) Which statement, A to D, can be used to define the term Brnsted-Lowryconjugateacid?A. Brnsted-Lowryconjugate acid is formed by an acid receiving a proton from a base.B. Brnsted-Lowryconjugateacid is formed by a base receiving a protonfrom an acid.C. Brnsted-Lowryconjugateacid is formed by an acid donating a protonto a base.D. Brnsted-Lowryconjugateacid is formed by a base donating a protonto an acid. The population is not uniformly spread over North America, nor are the population growth rates the same in all locations A False B True A manufacturing company regularly conducts quality control checks on the LED light bulbs it produces. Suppose that the historical failure rate is 0.5%. A quality control manager takes a random sample of 500 bulbs. Respond to the following:1) the probability that the sample contains no defective bulbs is:2) the probability that the manager finds 3 defective bulbs is:3) the probability that the manager finds 4 defective bulbs is:4) the expected number of defective bulbs for the sample is:5) the standard deviation of the number of defective bulbs for the sample described is: For this assignment, conduct some independent research on the raccoon and mountain gorilla. You may do your research online or from library books and magazines. Part 1: Fill in the table below and then answer the questions. Trait Raccoon Mountain Gorilla How many offspring do they have in a year, usually? What do they eat? Where are they found in the world? How many are there in the world? Are they hunted for meat, skin, fur, or other parts? Part 2: Which species is most vulnerable to extinction? Give at least three reasons why. Which species would be most harmed by environmental change that wiped out one area of its habitat? Why? Galena is the ore from which elemental lead is extracted. In the first step of the extraction process, galena is heated in air to form lead(II) oxide. 2PbS(s)+3O 2(g)2PbO(s)+2SO 2(g)H=827.4 kJ What mass of galena is converted to lead oxide if 975 kJ of heat are liberated? 203 g282 g406 g564 gJ/(gK) 3 C 14 C 22 C 47 C [H 2SO 4(l)]=814 kJ/mol; H f[HNO 3(I)]=174 kJ/mol; 19 kJ 2581 kJ 19 kJ 329 kJ The unit vectors on x, y and z axes of Cartesian coordinates are denoted i, j and k, respec- tively. Answer the following questions. (1) Let the scalar field = ez sin y + e* cos y and the vector field A = (2x - z)i - 2j+2k. Evaluate the component of the gradient of o in the direction of A at the point (1,0,1). (2) Evaluate the surface integral for the vector field A = zi-3j+ 4xyk, along the following surface S. S: 6x + 3y + z = 3 (x 0, y 0, z 0) What most accurately describes the relationship between the British colonies and Indigenous peoples in the Americas? British colonies wanted to integrate Indigenous peoples into their culture and religion. British colonies developed strong trading partnerships with Indigenous peoples. British colonies wanted to share land with Indigenous peoples. British colonies wanted Indigenous peoples out of the way so the colonies could profit more. Bernsteins proposed project has an initial cost of $128,600 and cash flows of $64,500, $98,300, and $15,500 for Years 1 to 3 respectively. If all negative cash flows are moved to Time 0 at a discount rate of 10 percent, what is the modified internal rate of return? Select one or more: a. 10.00% b. 9.90% c. 9.69% d. 9.97% e. 10.04% Use technology to find the P-value for the hypothesis test described below. The claim is that for a smartphone carrier's data speeds at airports, the mean is =14.00Mbps. The sample size is n=13 and the test statistic is t=1.337. P-value = (Round to three decimal places as needed. ) in its first year of business, laker corporation had sales of $2,000,000 and cost of goods sold of $1,200,000. laker expects returns in the following year to equal 8% of sales and 8% of cost of goods sold. the adjusting entry or entries to record the expected sales returns is (are): Use the five numbers 13,19,17,14, and 12 to complete parts a) through e) below. a) Compute the mean and standard deviation of the given set of data. The mean is x= and the standard deviation is s= (Round to two decimal places as needed.) The table below shows the freezing points of four substances.Substance Freezing point (C)benzene 5.50water 0.00butane 138nitrogen210.The substances are placed in separate containers at room temperature, and each container is gradually cooled. Which of these substances will solidify before the temperature reaches 0C?benzenewaterbutanenitrogen A gas made up of atoms escapes though a pinhole 1.82 times asfast as Xe gas. write the chemical formula of the gas. I have a question about the assignment below. Can someone explain what a "Use case grouping by first-cut menus and what a storyboard" is please? Can you also provide a short and simple design of what it would look like?Design a Graphical User-interface (GUI)a. Choose 1 of the following transition procedures from the use cases to your menuhierarchy:1. Use case groupings by first-cut menus, or2. Storyboards.b. Using CSS, HTML, and JavaScript, design the client-side system interfaceprototypes for your solution.c. Develop a minimum of 4 graphical user interfaces. Visit Fortune's website. You will find a list of the world's 500 largest companies. While going through the list, are you surprised by anything in particular? Is there any firm that interests you? Do you know which goods and services this company produces? Search the Internet to find out where these products are manufactured and assembled. Write a paragraph about this company: products offered, number of employees, and other details you learn about the firm. Why did the colonist oppose the Stamp Acts? Consider how theyfelt about the British Constitution. What expression represents the value of y? y equals the square root of quantity x times v end quantity y equals the square root of quantity w times z end quantity y equals the square root of quantity w times the sum of w plus z end quantity y equals the square root of quantity z times the sum of w plus z end quantity