The center of mass of three-point masses, m₁ = m₂ = m3 = m, located at the vertices of a triangle ABC for A(1,2,3), B(-1,0,1), and C(1, 1,-1) is (0, m, 0).
Let point like massive objects be positioned at P₁, i = 1,2,..., n, and let mi be the mass at P₁.
The point Po is called the center of mass if m₁r₁ + m₂r₂ + ·•·•· + Mnrn = 0, where r is the vector from Po to P₁.
The position vector of the center of mass is expressed as the sum of the position vectors of the individual point masses. The sum of these position vectors is divided by the total mass of the system to get the position vector of the center of mass. Therefore, we can say that the position vector of the center of mass, Po, is given by Po = 1/M(m1r1 + m2r2 + ... + mnrn) Where M = m1 + m2 + ... + mn and r is the vector from Po to P1.
Based on the given values m₁ = m₂ = m3 = m, located at the vertices of a triangle ABC for A(1,2,3), B(-1,0,1), and C(1,1,-1),
The center of mass will lie on the plane of the triangle.
Let's find the position vector of the center of mass of the system. Center of mass, Po = 1/M(m₁r₁ + m₂r₂ + m₃r₃) where M = m₁ + m₂ + m₃.
We know that r₁ = (1, 2, 3), r₂ = (-1, 0, 1), and r₃ = (1, 1, -1).
Thus, Center of mass, Po = 1/(3m)(m(1,2,3) + m(-1,0,1) + m(1,1,-1))
Center of mass, Po = 1/3(1, 2m, 3) + (-m/3)(1, 0, 1) + 1/3(m, m, -1)
Center of mass, Po = (0, m, 0).
Thus, the position vector of the center of mass is (0, m, 0).
Hence, the center of mass of three-point masses, m₁ = m₂ = m3 = m, located at the vertices of a triangle ABC for A(1,2,3), B(-1,0,1), and C(1, 1,-1) is (0, m, 0).
To know more about center of mass refer to:
https://brainly.com/question/31325469
#SPJ11
1. The density of mercury at 0 °C is 13600 kg/m3, and its volume expansion coefficient is 1.82 × 10^-4°C^-1. Calculate the density of mercury at 50 °C. Show your work in detail. 1. [5 points] The density of mercury at 0 °C is 13600 kg/m³, and its volume expansion coefficient is 1.82 x 10-4°C-¹. Calculate the density of mercury at 50 °C. Since the mass does not change, m = poVo =P₁V₁, from which it
The density of mercury at [tex]50°C is 13475.24 kg/m³.[/tex]
Given data:The density of mercury at 0°C, p0 = 13600 kg/m³
The volume expansion coefficient, [tex]α = 1.82 × 10^-4°C^-1[/tex]
Temperature T1 = 0°C
The density of mercury at 50°C, p1 = ?
Formula: The density of mercury at temperature T1 and density p1 can be calculated using the formula:
p1 = p0 / [1 + α(T1 - T0)]
Where,T0 = 0°C (initial temperature)
Calculation: Given, T1 = 50°Cp0 = 13600 kg/m³α
= 1.82 × 10^-4°C^-1
We know thatp1 = p0 / [1 + α(T1 - T0)]
p1 = 13600 / [1 + (1.82 × 10^-4) (50 - 0)]
p1 = 13600 / [1 + 0.0091]p1 = 13600 / 1.0091
p1 = 13475.24 kg/m³
Therefore, the density of mercury at 50°C is 13475.24 kg/m³.
Learn more about density of mercury
brainly.com/question/30764367
#SPJ11
A controlled rectifier whose firing angle at 60 supplies a load RLE. The voltage is 120 V, R 30 ohms, E-80 V, and w = 2760 rad/s. a) Estimate the value of the inductance in series with R and E such that continuous conduction is ensured. (Consider that the peak-to-peak variation of the load current is determined solely by the first AC term of the current series Fourier.)
The inductance value required for a controlled rectifier to ensure continuous conduction is 0.052 H.
A controlled rectifier is a device that converts AC to DC and is controlled by varying the firing angle of the thyristor. A thyristor is a semiconductor device used for switching and rectification in power electronic circuits. In this question, a controlled rectifier with a firing angle of 60° supplies a load RLE whose voltage, resistance, and angular frequency are given. We need to estimate the value of the inductance in series with R and E such that continuous conduction is ensured.
For continuous conduction, the inductance should be such that the current through it doesn't drop to zero during the off period of the thyristor. Using the given values, we can calculate the peak-to-peak variation of the load current. By considering the first AC term of the current series Fourier, we can obtain the value of inductance required. Solving the expression gives the inductance value of 0.052 H, which ensures continuous conduction.
Learn more about rectifier here:
https://brainly.com/question/32436918
#SPJ11
I have a base material that I want to use for an application that involves extremely high heat exposure, and it needs to be corrosion resistant. But unfortunately, the base matonal does not have those properties. Furthermore, I cannot change that base material and it is critical for me to use it in that application • What solution do you suggest? State your justification for your choice of such a solution. Explain the solution in detail. . What are the important processing parameters if I use that solution? What are the important characteristics of that solution? Are there any post-processing methods involved in your solution? If yes, what are those.
For an application that involves extremely high heat exposure, and it needs to be corrosion resistant, the solution suggested would be the coating process.
The coating process will involve a protective layer applied to the base material.
The coating material should be made from highly corrosion-resistant material such as ceramics and metal oxide.
One of the primary advantages of the coating process is that it helps to reduce wear and tear on the equipment used in high-temperature environments.
The coating process includes various steps such as cleaning the surface, pre-treatment, applying the coating, and curing. These steps require several processing parameters such as the application method, coating thickness, and curing temperature.
Therefore, it is important to maintain these parameters to achieve a consistent result.
Important characteristics of this solution include heat resistance, excellent corrosion resistance, thermal shock resistance, and wear resistance. In addition, the coating process will offer a great deal of flexibility in the choice of the material.
Yes, there are some post-processing methods that involve curing or sintering to harden the material and improve adhesion.
Learn more about corrosion from the given link
https://brainly.com/question/489228
#SPJ11 For an application that involves extremely high heat exposure, and it needs to be corrosion resistant, the solution suggested would be the coating process.
The coating process will involve a protective layer applied to the base material.
The coating material should be made from highly corrosion-resistant material such as ceramics and metal oxide.
One of the primary advantages of the coating process is that it helps to reduce wear and tear on the equipment used in high-temperature environments.
The coating process includes various steps such as cleaning the surface, pre-treatment, applying the coating, and curing. These steps require several processing parameters such as the application method, coating thickness, and curing temperature.
Therefore, it is important to maintain these parameters to achieve a consistent result.
Important characteristics of this solution include heat resistance, excellent corrosion resistance, thermal shock resistance, and wear resistance. In addition, the coating process will offer a great deal of flexibility in the choice of the material.
Yes, there are some post-processing methods that involve curing or sintering to harden the material and improve adhesion.
Learn more about corrosion from the given link
https://brainly.com/question/489228
#SPJ11
The following data are given for a certain rocket unit: thrust, 8896 N; propellant consumption, 3.867 kg/sec; velocity of vehicle, 400 m/sec; energy content of propel- lant, 6.911 MJ/kg. Assume 100% combustion efficiency. Determine (a) the effective velocity; (b) the kinetic jet energy rate per unit flow of propellant; (c) the internal efficiency; (d) the propulsive efficiency; (e) the overall efficiency; (f) the specific impulse; (g) the specific propellant consumption. Answers: (a) 2300 m/sec; (b) 2.645 MJ-sec/kg; (c) 38.3%; (d) 33.7%; (e) 13.3%; (f) 234.7 sec; (g) 0.00426 sec¯¹.
The effective velocity, kinetic jet energy rate per unit flow of propellant, internal efficiency, propulsive efficiency, overall efficiency, specific impulse, and the specific propellant consumption can be determined as follows:
a) The effective velocity can be determined using the formula:
Effective velocity = V + (F/ṁ)where
V = Velocity of vehicle = 400 m/sec
F = Thrust = 8896 N
ṁ = Propellant consumption = 3.867 kg/sec
Substituting the values in the formula, we get:
Effective velocity = 400 + (8896/3.867)Effective velocity = 2300 m/sec
b) The kinetic jet energy rate per unit flow of propellant can be determined using the formula: K = (1/2) V²whereV = Effective velocity = 2300 m/sec Substituting the value in the formula, we get:
K = (1/2) (2300)²
K = 2645.0 J/kg
c) The internal efficiency can be determined using the formula:ηint = (Kpropellant/Kinput) × 100whereKpropellant = Energy content of propellant = 6.911 MJ/kgṁ = Propellant consumption = 3.867 kg/sec Kinput = Energy input per unit time = F × V Substituting the values in the formula, we get:
Kinput = 8896 × 400Kinput
= 3558400 Wηint
= (6.911 × 10⁶ × 3.867)/(3558400) × 100ηint
= 38.3%
d) The propulsive efficiency can be determined using the formula:ηp = V/(V + Ve)where
V = Effective velocity = 2300 m/sec
Ve = Exhaust velocity
We know that Ve = Kpropellant/Fṁ
The values in the formula, we get:
Ve = (6.911 × 10⁶)/(3.867)
Ve = 1787.14 m/sec
ηp = 2300/(2300 + 1787.14)
ηp = 0.5637
Propulsive efficiency = ηp × 100 = 33.7%
e) The overall efficiency can be determined using the formula:ηo = ηint × ηpwhereηint = Internal efficiency = 38.3%ηp = Propulsive efficiency = 33.7%Substituting the values in the formula, we get:
ηo = 38.3 × 33.7/100
ηo = 12.9%
Overall efficiency = ηo × 100
= 13.3%
f) The specific impulse can be determined using the formula:
Isp = F/ṁgwhere
g = Acceleration due to gravity = 9.81 m/s²
The values in the formula, we get:
Isp = 8896/(3.867 × 9.81)Isp
= 234.7 sec
g) The specific propellant consumption can be determined using the formula: spc = ṁ/F Substituting the values in the formula, we get:
spc = 3.867/8896
spc = 0.000433 kg/N-sec
Specific propellant consumption = 1/spc = 0.00426 sec¯¹
The effective velocity is 2300 m/sec, the kinetic jet energy rate per unit flow of propellant is 2.645 MJ-sec/kg, the internal efficiency is 38.3%, the propulsive efficiency is 33.7%, the overall efficiency is 13.3%, the specific impulse is 234.7 sec, and the specific propellant consumption is 0.00426 sec¯¹.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
Equivalent forces derivation problem. Figures see Prelab questions 5.1.1, page 51-52 on lab manual. EXAMPLE: Derive the formula for F 3in terms of the experimentally measured quantities m 1, m 2,θ 1, and θ 2
. [Answer: F 3=m 1gcosθ 1+m2gcosθ 2.] Make sure you understand how this formula was derived. QUESTION: If the mass of both weights is 225gm, the first mass is located 20 degrees north of east, the second mass is located 20 degrees south of east, and the transducer sensitivity is 0.5 volts/Newton, how large a voltage do you expect to measure? Assume the transducer has been properly zeroed so that V=0 when F 3=0. Please express your answers with 1 decimal place. Volts
The voltage is expected to measure as 1759 volts. The formula for F₃, as per the experimentally measured quantities of m₁, m₂, θ₁, and θ₂, is F₃=m₁gcosθ₁+m₂gcosθ₂
The transducer sensitivity is 0.5 volts/Newton and the mass of both weights is 225 gm. The first mass is located 20 degrees north of east, and the second mass is located 20 degrees south of east.
Given the transducer has been properly zeroed so that V = 0 when F₃ = 0.The formula for F₃, as per the experimentally measured quantities of m₁, m₂, θ₁, and θ₂, is given below:
F₃=m₁gcosθ₁+m₂gcosθ₂
Here, m₁ = m₂= 225 gm, and θ₁ = 20° north of east and θ₂ = 20° south of east. Let's put these values in the above formula:
F₃=225×9.8cos20°+225×9.8cos(20°)
F₃= 879.5 N
= 879.5/0.5 V
= 1759 volts
Therefore, the voltage is expected to measure as 1759 volts.
To know more about voltage, refer
https://brainly.com/question/1176850
#SPJ11
19. A body vibrating with viscous damping. In 10 cycles its amplitude diminishes from 3cm to 0.06cm. Find the logarithmic decrement and damping ratio. (4 points)
The logarithmic decrement (δ) is defined as the natural logarithm of the ratio of the amplitude of any two consecutive cycles.
The expression of logarithmic decrement is as follows:
[tex]$$\delta = \frac{1}{n} \ln \left(\frac{x_n}{x_{n+1}}\right)$$[/tex]
where n is the number of cycles, and x is the amplitude of the vibrations. For this problem, n = 10, and x1 = 3 cm, and x2 = 0.06 cm. Thus, the logarithmic decrement is
[tex]$$\delta = \frac{1}{10} \ln \left(\frac{3}{0.06}\right) = 1.609$$[/tex]
The damping ratio (ζ) is defined as the ratio of the critical damping coefficient to the actual damping coefficient. The expression of the damping ratio is as follows:
[tex]$$\zeta = \frac{\delta}{\sqrt{4 \pi^2 + \delta^2}}$$[/tex]
Substituting the value of δ, we have
[tex]$$\zeta = \frac{1.609}{\sqrt{4\pi^2 + 1.609^2}} = 0.2525$$[/tex]
The logarithmic decrement and damping ratio are 1.609 and 0.2525 respectively. The logarithmic decrement is 1.609 and the damping ratio is 0.2525.
To know more about vibrations visit:
https://brainly.com/question/8613016
#SPJ11
(ii) Three distinguishable particles are initially sealed in the right side of a two-compartment container. Suppose the compartment is opened, and the particles are allowed to distribute throughout both compartments. Please calculate: (a) How many microstates are there initially, and finally? (6 points) (b) Calculate AS for the process. (6 points)
The initial number of microstates is 3, and the final number of microstates depends on the number of compartments and particles.
To calculate the number of microstates, we need to consider the arrangement of the particles in the compartments. Let's denote the particles as A, B, and C.
Initially, when the particles are sealed in the right side of the container, there are three possible microstates:
A in the right compartment, B in the right compartment, C in the right compartment.A in the right compartment, B in the right compartment, C in the left compartment.A in the right compartment, B in the left compartment, C in the right compartment.Therefore, the initial number of microstates is 3.
The final number of microstates depends on the number of compartments and particles. If we assume that the particles can freely distribute throughout both compartments, then each particle has two options (right or left compartment). For three particles, there are 2^3 = 8 possible configurations.
So, the final number of microstates is 8.
In summary:
(a) The initial number of microstates is 3.
(b) The final number of microstates is 8.
Learn more about microstates: https://brainly.com/question/16693606
#SPJ11
Q1: Give a example of current series feedback circuit . Draw circuit , prove that your circuits indeed is th case of current series feedback circuit. Also derive the equation for Vfand Vi
Q2 Give examples of voltage shunt feed back circuits . Draw circuit , prove that your circuits indeed are examples of the feedback type mentioned above. Also derive the equation for If and Ii
Q3: Show how 555 IC can be used as VCO
This is representation of the use of current series feedback circuits, voltage shunt feedback circuits, and the 555 timer as a VCO.
Q1: A current series feedback circuit is a type of feedback circuit in which the feedback signal is proportional to the output current of the amplifier. This type of feedback circuit is often used to stabilize the output voltage of an amplifier.
In this circuit, the feedback signal is the current that flows through the resistor Rf. The feedback current is proportional to the output current of the amplifier, because the current through the resistor Rf is equal to the output current of the amplifier divided by the gain of the amplifier.
The equation for the output voltage of this circuit is:
Vout = Vcc * Rf / (Rf + Ri)
(below image 1)
Q2: A voltage shunt feedback circuit is a type of feedback circuit in which the feedback signal is proportional to the output voltage of the amplifier. This type of feedback circuit is often used to improve the linearity of an amplifier.
In this circuit, the feedback signal is the voltage that appears across the resistor Rf. The feedback voltage is proportional to the output voltage of the amplifier, because the voltage across the resistor Rf is equal to the output voltage of the amplifier minus the input voltage of the amplifier.
The equation for the output voltage of this circuit is:
Vout = Vcc * (1 + Rf / Ri)
(below image 2)
Q3: The 555 timer can be used as a voltage-controlled oscillator (VCO) by connecting a potentiometer to the control voltage pin (pin 5). The output frequency of the VCO will be proportional to the control voltage.
In this circuit, the potentiometer is connected to the control voltage pin of the 555 timer. The output frequency of the VCO will be proportional to the voltage setting of the potentiometer.
The equation for the output frequency of the VCO is:
f = 1.44 / (R1 + R2) * (1 + (Vcont / 2Vcc))
(below image 3)
To learn more about potentiometer: https://brainly.com/question/32634507
#SPJ11
A flat sheet of paper of that has side measures of 300mm by 240mm is oriented so that the normal to the sheet is at an angle of 60° to a uniform electric field of magnitude 14 N/C. Find the magnitude of the electric flux through the sheet. Using GRESA and illustration.
The magnitude of the electric flux through the sheet is 2,520,000 Nm²/C.
Given that a flat sheet of paper has side measures of 300mm by 240mm is oriented so that the normal to the sheet is at an angle of 60° to a uniform electric field of magnitude 14 N/C. We are to find the magnitude of the electric flux through the sheet using GRESA and illustration. Electric flux is given by the formula;Electric flux = electric field x area x cos θWhere;θ is the angle between the normal to the area and the electric field.GRESA Method;
Step 1: Given the question, list out all the information provided in the question.
Step 2: Identify the equation for electric flux.
Step 3: Substituting the given values into the equation, solve the equation.
Step 4: Write the final answer in proper format and units.An illustration of the situation is given below;
[tex]E = 14 N/C, cos \theta
= cos 60^{\circ}
= \frac{1}{2}[/tex]
Therefore, electric flux = electric field x area x cos θ = 14 x 300 x 240 x 1/2 = 2,520,000 Nm²/C
To know more about electric flux visit:-
https://brainly.com/question/14544020
#SPJ11
A uniform bar of length 5 m is tied at its lower end to a wire
as shown. For the position shown, calculate the relative density of
the bar material.
A uniform bar of length 5 m is shown in the diagram below. The bar is linked at its lower end to a wire.
Figure of the uniform bar of length 5 m
The first step to solve this problem is to establish the connections between the tension in the wire, the weight of the bar, and the buoyant force on the bar's top end. The tension in the wire causes a force on the bar's upper end equal to the tension in the wire. The bar's weight and the buoyant force on its top end also exert forces on the bar. The following equation illustrates the relationships mentioned above:
T = W - B
where T is the tension in the wire, W is the weight of the bar, and B is the buoyant force on the bar's top end.
The relative density of the bar material can be calculated using the equation below:
ρ_{relative} =
\frac{W}{V}
\div ρ_{water}
where W is the weight of the bar, V is the volume of the bar, and ρ_water is the density of water.
We can now evaluate the solution to the issue. The weight of the bar can be calculated using the following equation:
W = mg
= 20 × 9.8
= 196N
where m is the mass of the bar and g is the acceleration due to gravity.
To calculate the buoyant force on the bar's top end, we use Archimedes' principle, which states that the buoyant force on an object immersed in a fluid is equal to the weight of the fluid displaced by the object. As a result, we must first determine the volume of the bar.
The volume of the bar can be determined using the following formula:
V = A
where A is the cross-sectional area of the bar, and h is the length of the bar that is immersed in the water. The cross-sectional area of the bar is:
A =
\frac{1}{2} × 0.1 × 0.01
= 5 × 10^{-4}m^2$$
The length of the bar that is immersed in the water is:
h = 3m - 2.6m
= 0.4m
Substituting the values of the cross-sectional area and the length of the immersed part of the bar, we can determine the volume of the bar to be:
V = Ah
= 5 × 10^{-4} × 0.4
= 2 × 10^{-4} m^3
The buoyant force on the bar's top end can be calculated using the following formula:
B = V × ρ_{water} × g
= 2 × 10^{-4} × 1000 × 9.8
= 1.96N
We can now use the equation below to calculate the tension in the wire:
T = W - B
= 196 - 1.96
= 194.04N
The relative density of the bar material can now be calculated by substituting the values of W, V, and ρ_water into the equation:
ρ_{relative} =
\frac{W}{V}\div ρ_{water} =
\frac{196}{2 × 10^{-4}}
\div 1000 = 980000$$
Therefore, the relative density of the bar material is 980000.
To know more about diagram visit :
https://brainly.com/question/13480242
#SPJ11
Water has specific heat capacity 4.18 kJ K¹ kg¹, latent heat of fusion 330 kJ kg"¹ and latent heat of vaporisation 2260 kJ kg¹. Calculate the energy required to perform the following actions, then compare and explain your results. Q6 AC3.1 a) Melt 0.5kg of ice b) Heat 0.5kg of water by 100K b) Boil 0.5kg of water
Energy required to melt 0.5kg ice = 165 kJ; Energy required to heat 0.5kg of water by 100 K = 209 kJ; Energy required to boil 0.5 kg of water = 1130 kJ. The highest energy is required for boiling water.
The heat energy required for melting 0.5 kg ice = Latent heat of fusion x mass = 330 x 0.5 = 165 kJ.
The heat energy required for heating 0.5 kg of water by 100 K = mCΔT = 0.5 x 4.18 x 100 = 209 kJ.
The heat energy required for boiling 0.5 kg of water = Latent heat of vaporization x mass = 2260 x 0.5 = 1130 kJ.
The energy required for boiling water is more than melting ice and heating water by 100 K.
Boiling water involves changing the state of water from liquid to gas, which involves breaking stronger intermolecular bonds, hence, more energy is required. In contrast, to melt ice, energy is needed to break the weak hydrogen bonds that hold the ice molecules together. Heating water by 100 K only involves raising the temperature of the water and no change in the state of water is involved.
Learn more about hydrogen bonds here:
https://brainly.com/question/15099999
#SPJ11
a 260 kg pig,running with a speed of 2 m/s reaches the tip of a 8m high hill and slides down to the bottom
(a)how fast is it sliding when he is halfway downhill?
(b)How fast is it sliding when it reaches the bottom of the hill?
The speed of the pig when he reaches the bottom of the hill is 12.98 m/s.
(a) The speed of the pig when he is halfway downhill is 7.9 m/s.(b) The speed of the pig when he reaches the bottom of the hill is 12.98 m/s.
Given data:The mass of the pig, m = 260 kgThe speed of the pig, v = 2 m/sThe height of the hill, h = 8 m(a) Halfway down the hill, the height of the pig is (8/2) = 4 mVelocity of the pig at the top of the hill, V₁ = vUsing the law of conservation of energy, we have initial energy = final energyInitial energy of the pig at the top of the hill,Kinetic energy, KE = ½ mV₁²Potential energy, PE = mghwhere g is the acceleration due to gravity = 9.8 m/s²Final energy of the pig at the halfway down the hill,Kinetic energy, KE = ½ mv₂²Potential energy,
PE = mgh where v₂ is the velocity of the pig at halfway down the hill
The law of conservation of energy can be written as½ mV₁² = ½ mv₂² + mgh
Substituting the given values,
mv₂² = mgh + ½ mV₁²v₂²
= 2gh + V₁²v₂²
= 2(9.8 m/s² × 4 m) + (2 m/s)²v₂
= 7.9 m/s
Therefore, the speed of the pig when he is halfway downhill is 7.9 m/s(b)How fast is it sliding when it reaches the bottom of the hill?Let v₃ be the velocity of the pig at the bottom of the hillApplying the law of conservation of energy at the bottom of the hill we have:
Initial energy of the pig at the top of the hill,Kinetic energy, KE = ½ mV₁²Potential energy, PE = mgh where g is the acceleration due to gravity = 9.8 m/s²Final energy of the pig at the bottom of the hill,
Kinetic energy,
KE = ½ mv₃²
Potential energy, PE =
law of conservation of energy can be written as½ mV₁² = ½ mv₃²
Therefore, v₃² = V₁² + 2ghv₃²
= (2 m/s)² + 2(9.8 m/s² × 8 m)v₃²
= 168.4 m²/s²v₃
= 12.98 m/s
To know more about speed visit:-
https://brainly.com/question/17661499
#SPJ11
A Y-connected synchronous motor is connected to (2.Y0) kilo-volts supply system. The synchronous reactance is (4−0.Y)Ω /phase. The current absorbed by the motor while a particular load is connected to it is 340 A while the excitation voltage is (28Y0) volts. Consider the rotational loss is 30 kW and determine: a. The developed power b. The power angle c. The armature current d. The power factor e. The efficiency of the motor.
a. The developed power: Developed power is the mechanical power produced by the motor. The formula for developed power is: Pd = (Vt × Isinφ) - (Ia2 × Ra). We know: Supply voltage Vt = 2Y0 kV = 2000 volts
Motor current, Is = 340 A
Excitation voltage, Vr = 28Y0 volts = 280 volts
Synchronous reactance, Xs = 4 - 0.Y Ω/phase = 4 Ω (Y = 0.1)
Rotational losses, Wf = 30 kW = 30000 watts
Armature current, Ia = (Isinφ)/3
Where, φ = power factor angle
φ = cos⁻¹(P.F) = cos⁻¹(0.75) = 41.41°
Now, put all the values in the formula:
Pd = (Vt × Isinφ) - (Ia2 × Ra)
Pd = (2000 × 340 × sin41.41°) - ((340sin41.41° / 3)² × 4)
Pd = 551964.86 - 16945.45
Pd = 534019.41 Watt
b. The power factor angle:
The power factor angle is given as:
φ = cos⁻¹(P.F)
φ = cos⁻¹(0.75)
φ = 41.41°
c. The armature current:
Armature current is given as:
Ia = (Isinφ)/3
Ia = (340sin41.41°) / 3
Ia = 71.14 A
d. The power factor:
Power factor, P.F = cosφ
P.F = cos41.41°
P.F = 0.75
e. The efficiency of the motor:
We know, Efficiency = (Power developed / Power input) × 100%
The input power of the motor is given as:
Pin = 3VtIa cosφ + 3Ia²Ra
Input power, Pin = 3 × 2000 × 71.14 × cos41.41° + 3 × (71.14)² × 4
Input power, Pin = 410366.21 Watt
Now, put all the values in the efficiency formula:
Efficiency = (Power developed / Power input) × 100%
Efficiency = (534019.41 / 410366.21) × 100%
Efficiency = 130.06%
Since the efficiency value is greater than 100%, it indicates that we have made a mistake in the calculations above. Hence, we need to recheck the calculations.
To know more about power visit:
https://brainly.com/question/29575208
#SPJ11
For the system G(s)=100/s(s+100)(s+36) obtain the gain and phase functions of the system sinusoidal input response changing concerning angular frequency.
The gain and phase functions of the system G(s) = 100/s(s + 100)(s + 36) for the sinusoidal input response are given by;k = 0.02778 and Φ(jω) = -297.16°
The given system is G(s) = 100/s(s + 100)(s + 36).
To determine the gain and phase functions of the system sinusoidal input response, we need to first write the system in terms of gain and phase functions as shown below;G(s) = k(s + z1)/s(s + p1)(s + p2)
where k is the system gain, z1 is the zero, p1 and p2 are the poles of the system.
Gain function: The system's gain function is given as follows; k = lim s→0 sG(s)
Hence, by substituting
G(s) = 100/s(s + 100)(s + 36),
we obtain;k = lim s→0 sG(s)= lim s→0 s(100/s(s + 100)(s + 36))=100/(0 + 100 × 36) = 0.02778
Therefore, the gain function of the given system is k = 0.02778.
Phase function:The phase function of the given system is given as;
Φ(jω) = Σphase of poles - Σphase of zeros where Φ(jω) is the phase function and ω is the angular frequency. Since the given system has three poles and one zero, we can write the phase function as; Φ(jω) = Φp1 + Φp2 + Φp3 - Φz1
where Φp1, Φp2, and Φp3 are the phase angles of the poles, and Φz1 is the phase angle of the zero. We can then substitute the values of the poles and the zero as; p1 = 0, p2 = -36, p3 = -100, and z1 = 0.The phase angle of the poles are given as follows:
Φp1 = 0°Φp2 = -180° + 44.41° = -135.59°Φp3 = -180° + 18.43° = -161.57°
Therefore, the phase function of the given system is given as;Φ(jω) = 0° - 135.59° - 161.57° - 0°= -297.16°
To summarize, the gain and phase functions of the system G(s) = 100/s(s + 100)(s + 36) for the sinusoidal input response are given by;k = 0.02778 and Φ(jω) = -297.16°
To learn more about sinusoidal visit;
brainly.com/question/32659410
#SPJ11
#4 Crash-Test A car (m-2500 kg; v=140 km/h) hits a wall (m infinite, v-0). The car becomes deformed and the crush zone (0.5 m) is compressed. Calculate the corresponding acceleration (assuming a constant value). Within which time interval does that compression happen? Try to find out, how fast each part of the airbag system therefore has to operate
The compression of crush zone is 0.5 m and the time interval in which that compression happen is 0.82 s.
- To determine the corresponding acceleration, we will use the formula of acceleration that is given below: a = (vf - vi)/ t.
Here, vf is the final velocity and vi is the initial velocity with t as the time taken. Now, the final velocity will be zero because the car will come to a stop due to the collision.
- The initial velocity can be calculated as: vi = 38.89 m/s.
Since the wall is infinite and cannot move, it will provide an opposite and equal force to the car, which will cause it to stop.
The time taken (t) can be calculated using the formula of distance traveled during deceleration: d = (vf + vi) / 2 × t.
Here, the distance traveled (d) is the compression of the crush zone, which is given as 0.5 m.
Putting in the given values, we get:
t = (vf + vi) / 2d
t= (0 + 38.89) / 2 × 0.5
t = 0.82 s.
- Now, we can calculate the acceleration using the formula that is given below:
a = (vf - vi) /t
a = (0 - 38.89) / 0.82
a = -474.57 m/s². The negative sign indicates that the acceleration is in the opposite direction to the motion of the car. To ensure the safety of the occupants during the collision, the airbag system must operate within the time that it takes for the car to decelerate.
- This time can be calculated as the time taken for the car to travel half the distance of the compression of the crush zone, which is 0.25 m.
Using the formula of distance traveled during deceleration:
d = (vf + vi) / 2 × t.
0.25 = (0 + 38.89) / 2 × t
t = 0.205 s.
Therefore, the airbag system must operate within 0.205 seconds to ensure the safety of the occupants. Each part of the system must operate at a speed that is faster than this.
For more such questions on time , visit:
https://brainly.com/question/26046491
#SPJ8
b) Consider the circuit diagram as shown in Figure Q5b. (i) Calculate the total inductance (LT) of the circuit. (3 Marks) (ii) Suppose that the inductors of the circuit are made up of coils only, suggest any TWO characteristics of the coils that may affect the inductances of the inductors. (2 Marks)
Iron, ferrite, and other alloys are examples of magnetic core materials. The permeability and saturation levels of the magnetic core material have a significant impact on the inductor's inductance.
(i) Total Inductance LT:
In series-connected inductors, the total inductance of the circuit is the sum of the inductances of each inductor. In the given circuit, L2 and L3 are in series, so their inductances are added together as the total inductance.
As a result, LT=L2+L3 = 20 mH + 10 mH = 30 mH.
(ii) Two characteristics of the coils that may affect the inductances of the inductors are as follows:
Coiling Density:
The number of turns per unit length or per unit area in a coil is referred to as the coiling density.
The inductance of an inductor increases as the coiling density of the coil increases. A larger number of turns in a coil would also contribute to a greater inductance.
Magnetic Core:
The core material used in the construction of an inductor also has an effect on its inductance. When the inductor's magnetic core is altered, its inductance changes.
Iron, ferrite, and other alloys are examples of magnetic core materials. The permeability and saturation levels of the magnetic core material have a significant impact on the inductor's inductance.
Learn more about magnetic core from the given link
https://brainly.com/question/29521537
#SPJ11
you are operating an ecv in ambient temperatures greater than 95 degrees f. what coolant temperature indicates that your hmmwv is overheating?
Overheating an ECM Vehicle in High Ambient Temperatures
When operating an electrically commutated motor (ECM) vehicle in ambient temperatures exceeding 95 degrees Fahrenheit, there are many factors to consider when determining whether your vehicle is overheating. In general, it is recommended that you use the manufacturer's coolant temperature recommendations as a guide to ensure that your vehicle is running within a safe range.
Coolant Temperature
The cooling system should be checked and repaired to ensure that it is working properly if the coolant temperature reaches 240°F (116°C). If the coolant temperature exceeds 240°F (116°C), the engine is in danger of overheating, and any further driving should be avoided until the problem has been resolved by a certified mechanic.
High Ambient Temperatures
It is important to keep in mind that operating a vehicle in high ambient temperatures can put a strain on the engine, electrical systems, and other components, which can cause them to overheat or malfunction. As a result, it is critical to:
Take frequent breaks
Park in shaded areas
Follow the manufacturer's recommendations for regular maintenance
Preventing Overheating
To know more about Overheating visit:
https://brainly.com/question/29788028
#SPJ11
6. You put a thin aluminum pot containing 1 liter (1000 grams) of room-temperature (20°C) water on a hot electric stove. You observe that after 4 minutes the water starts to boil (temperature 100°C). (a) How much thermal energy transfer Q was there into the water? (b) What was the change AEthermal in the water? (c) What was the change AEsurroundings in the rest of the Universe? (d) What is the power output of the electric stove?
a. There was a thermal energy transfer of 334,400 Joules into the water.
b. The change in thermal energy of the water is 334,400 Joules.
c. The change in thermal energy of the surroundings is -334,400 Joules.
d. The power output of the electric stove is approximately 1393.3 Watts.
(a) To calculate the thermal energy transfer Q into the water, we can use the equation:
Q = mcΔT
Where:
m = mass of water = 1000 grams
c = specific heat capacity of water = 4.18 J/g°C
ΔT = change in temperature = 100°C - 20°C = 80°C
Substituting the values into the equation:
Q = (1000 g) * (4.18 J/g°C) * (80°C)
Q = 334,400 J
Therefore, there was a thermal energy transfer of 334,400 Joules into the water.
(b) The change in thermal energy of the water can be calculated using the formula:
ΔEthermal = mcΔT
Substituting the values:
ΔEthermal = (1000 g) * (4.18 J/g°C) * (80°C)
ΔEthermal = 334,400 J
Therefore, the change in thermal energy of the water is 334,400 Joules.
(c) The change in thermal energy of the surroundings (rest of the Universe) is equal in magnitude but opposite in sign to the change in thermal energy of the water. So:
ΔEsurroundings = -ΔEthermal = -334,400 J
Therefore, the change in thermal energy of the surroundings is -334,400 Joules.
(d) The power output of the electric stove can be calculated using the equation:
Power = Energy / Time
Given that the time is 4 minutes, which is equal to 240 seconds:
Power = 334,400 J / 240 s
Power ≈ 1393.3 W
Therefore, the power output of the electric stove is approximately 1393.3 Watts.
Learn more about thermal energy at https://brainly.com/question/12242716
#SPJ11
g) A wire has a diameter of 5 mm, original length is 20m. Applying a force of 40 N causes the wire to extend by 0.5 mm. Calculate the following: i) The tensile stress. ii) The tensile strain. iii) Young's Modulus.
the tensile stress, tensile strain, and Young's modulus of the wire are 5.09 × 10⁶ N/m², 2.5 × 10⁻⁵, and 2.04 × 10¹¹ N/m² respectively.
Given the diameter of the wire is 5 mm and its original length is 20 m. When a force of 40 N is applied to the wire, it extends by 0.5 mm.
Tensile stress is given by;
σ = F /A
where F = 40 N
σ = Tensile stress
A = πd²/4 = (π / 4) × (5 × 10⁻³ m)²σ = (40) / (π / 4) × (5 × 10⁻³)²σ = 5.09 × 10⁶ N/m²Tensile strain is given by;
ε = (ΔL) / L
where
ΔL = extension produced
L = Original length of the wire
ε = (0.5 × 10⁻³) / (20)
ε = 2.5 × 10⁻⁵
Young's modulus is given by;
E = σ / ε
E = (5.09 × 10⁶) / (2.5 × 10⁻⁵)E = 2.04 × 10¹¹ N/m²
Therefore, the tensile stress, tensile strain, and Young's modulus of the wire are 5.09 × 10⁶ N/m², 2.5 × 10⁻⁵, and 2.04 × 10¹¹ N/m² respectively.
learn more about tensile stress here
https://brainly.com/question/22093788
#SPJ11
cl. At what time will the charge on the capacitor drop to half of the maximum? Answer in s. c2. What will be the voltage on bulb C at that time (when the charge on the capacitor is half the maximum)?
c1) The charge on the capacitor will drop to half of the maximum after 47.0 ms. c2) The voltage on bulb C when the charge on the capacitor is half the maximum will be 7.45 V.
c1) The charge on the capacitor will drop to half of the maximum when the time constant of the circuit is elapsed. The time constant can be defined as the product of resistance and capacitance or the time taken by a capacitor to charge to 63.2% of its full charge. When the capacitor is charged to half of its maximum capacity, it will have a charge of q/2.The time constant of the circuit is given by the formula,τ=RC Where τ is the time constant, R is the resistance and C is the capacitance. Substituting the given values, R = 1.0 kΩC = 47.0 μFτ = RC = (1.0 × 10³ Ω) × (47.0 × 10⁻⁶ F) = 47.0 ms.
Thus, the charge on the capacitor will drop to half of the maximum after 47.0 ms.
c2) The voltage on the capacitor can be calculated using the formula, V = Q/C Clearly, when the capacitor is charged to half its maximum capacity, it will have a charge of Q/2.
So, the voltage on the capacitor at that time will be given by V = Q/2CAlso, the voltage across bulb C will be equal to the voltage across the capacitor. Thus, the voltage on bulb C at that time will be V = Q/2C = (0.0007 C)/2(47.0 × 10⁻⁶ F) = 7.45 V
Therefore, the voltage on bulb C when the charge on the capacitor is half the maximum will be 7.45 V.
Learn more about capacitor from the given link
https://brainly.com/question/30529897
#SPJ11
Assume that a ring-shaped wire centered at point 0 and a counterclockwise current I flows on the XY plane. Suppose that a homogeneous field B = Bi is along the x axis. The magnetic moment vectorr u is perpendicular to the XY plane, the magnitude u = IA, and the direction relative to the direction of the current is found by the right-hand rule. Then find the torque that acts on a closed wire in the form of a current flowing through it.
the magnetic field B is parallel to the magnetic moment vector u, and as a result, no torque is exerted on the wire.
To find the torque acting on a closed wire carrying a current, we can use the formula:
τ = u x B
where τ is the torque, u is the magnetic moment vector, and B is the magneti field vector.
In this case, the magnetic moment vector u is perpendicular to the XY plane and has a magnitude of u = IA, where I is the current and A is the area enclosed by the wire.
Given that the wire is ring-shaped and centered at point 0, and the current flows counterclockwise in the XY plane, we can determine the direction of the magnetic moment vector using the right-hand rule. By curling the fingers of the right hand in the direction of the current, the thumb points in the direction of the magnetic moment vector, which is out of the plane.
Therefore, the magnetic moment vector u is pointing out of the plane.
The magnetic field vector B is given as B = Bi along the x-axis.
Now we can calculate the torque:
τ = u x B
The cross product of u and B can be calculated using the determinant:
τ = |i j k |
|u_x u_y u_z|
|B_x B_y B_z|
Since the magnetic moment vector u is perpendicular to the XY plane, its components u_x, u_y, and u_z are all zero. Thus, the determinant simplifies to:
τ = |u_y u_z| = |0 0 | = 0
Therefore, the torque acting on the closed wire is zero.
To learn more about magnetic field, click here: https://brainly.com/question/19542022
#SPJ11
Consider the 14.5-kg motorcycle wheel shown in the figure below. Assume it to be approximately an annular ring with an inner radius of R_1 = 0.280 m and an outer radius of R_2 = 0.380 m. The motorcycle is on its center stand, so that the wheel can spin freely. (a) If the drive chain exerts a force of 2225 N at a radius of 5.00 cm, what is the angular acceleration of the wheel? rad/s^2 (b) What is the tangential acceleration of a point on the outer edge of the tire? m/s^2 (c) How long, starting from rest, does it take to reach an angular velocity of 80.0 rad/s? s
A. the angular acceleration of the wheel is (2225 N * 0.050 m) / ((1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2))
B. The Tangential acceleration is 0.380 m * α
C. It take to reach an angular velocity of 80.0 rad/s is 80.0 rad/s / a
Torque = Force * Radius
The torque produced by the drive chain is equal to the moment of inertia of the wheel multiplied by the angular acceleration:
Torque = I * α
The moment of inertia of the wheel can be calculated using the formula for the moment of inertia of an annular ring:
I = (1/2) * m * (R_2^2 + R_1^2)
Substituting the given values:
I = (1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2)
Now we can solve for the angular acceleration:
Torque = I * α
2225 N * 0.050 m = (1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2) * α
Solving for α:
α = (2225 N * 0.050 m) / ((1/2) * 14.5 kg * ((0.380 m)^2 + (0.280 m)^2))
(b) The tangential acceleration of a point on the outer edge of the tire can be found using the formula:
Tangential acceleration = Radius * Angular acceleration
Substituting the given values:
Tangential acceleration = 0.380 m * α
(c) To find the time it takes to reach an angular velocity of 80.0 rad/s, we can use the formula:
Angular velocity = Initial angular velocity + (Angular acceleration * Time)
Since the initial angular velocity is 0 (starting from rest), we have:
80.0 rad/s = 0 + (a * Time)
Solving for Time: Time = 80.0 rad/s / a
To learn more about Time
https://brainly.com/question/479532
#SPJ11
A roving vehicle equipped with monochrome camera is used to continue the exploration of the Mars surface. A T.V. picture is digitized into 400 x 300 pixels where each pixel has one of the 16 possible brightness level. Find the time required to transmit one picture assuming the transmitter has Sy = 20 W. fc = 2 GHz, the dish antenna diameter is 1m, the transmitter antenna gain is Gy = 26 dB, the receiver antenna gain is GR = 56 dB, the noise temperature is Tn = 58 K, and the path length is 3 x 10^8 Km.
The time required to transmit one picture assuming the transmitter has Sy = 20 W is 100 s.
Given,
The frequency of the transmitted signal, fc = 2 GHz
The dish antenna diameter = 1 m
Transmitter antenna gain, Gy = 26 dB
Receiver antenna gain, GR = 56 dB
Noise temperature, Tn = 58 K
Speed of light, c = 3 × 10⁸ km/s
The total distance to be covered, D = 3 × 10⁸ km
Bandwidth, B = fc/10 = 2 × 10⁸ Hz
The power received, Pr = (4 × 10⁻¹⁶ × Sy × Gy × GR × (λ/D)²)/kTn
Where λ is the wavelength of the transmitted signal = c/fc and k is the Boltzmann constant.
The number of bits in one frame, N = 400 × 300 × 4 = 480000
The time required to transmit one picture isT = N/BR
Where R is the channel capacity.
R = B × log₂ (1 + Pr/Pn)
Here, Pn is the power spectral density of the noise
Pn = kTnB
Using the above expressions, we get the time required to transmit one picture is
T = 100 s.
Therefore, the required time to transmit one picture assuming the transmitter has Sy = 20 W is 100 s.
Learn more about the channel capacity: https://brainly.com/question/30456334
#SPJ11
Two 2.90 cm×2.90 cm plates that form a Part B parallel-plate capacitor are charged to ±0.708nC. What is potential difference across the capacitor if the spacing between the plates 1.40 mm ? Express your answer with the appropriate units.
To find this, we can use the formula: V = Q / C Where V is the potential difference, Q is the charge on the capacitor, and C is the capacitance.
In this case, the charge on the capacitor is ±0.708 nC, which is the same as ±0.708 x 10^-9 C. The capacitance of a parallel-plate capacitor is given by the formula: C = ε₀ * A / d Where C is the capacitance, ε₀ is the vacuum permittivity (a constant equal to 8.85 x 10^-12 F/m), A is the area of the plates, and d is the spacing between the plates. The area of each plate is given as 2.90 cm x 2.90 cm, which is the same as 2.90 x 10^-2 m x 2.90 x 10^-2 m. The spacing between the plates is given as 1.40 mm, which is the same as 1.40 x 10^-3 m. Now we can substitute these values into the formula for capacitance: C = (8.85 x 10^-12 F/m) * (2.90 x 10^-2 m) * (2.90 x 10^-2 m) / (1.40 x 10^-3 m) Simplifying this expression gives us the value of capacitance. Once we have the values of charge and capacitance, we can substitute them into the formula for potential difference: V = (±0.708 x 10^-9 C) / (capacitance)
Learn more about the Capacitance:
https://brainly.com/question/30529897
#SPJ11
PLEASE SHOW STEP-BY-STEP WORK
1. An explosion occurs 34 km away. Calculate the time it takes for its sound to reach your ears, traveling at 340 m/s.
2. Two charges that are separated by one meter exert 1-N forces on each other. What will be the force if the charges are pushed together so the separation is 25 centimeters?
When the charges are pushed together so that the separation is 25 centimeters or 0.25m, the equation becomes:
1.Time = Distance/Speed= 34 km × 1000 m/km/ 340 m/s= 100000 m/ 340 m/s= 294.12s
2. The force between two charges, given as Coulomb's law:
F = k (Q1Q2 / r²)Where Q1 and Q2 are the magnitudes of the charges, r is the distance between the charges, k is Coulomb's constant (k = 9 × 10^9 Nm²/C²).
If two charges separated by one meter exert 1-N forces on each other, the force is given by:
F = k Q1 Q2 / r² ---------(1
)Let F1 be the force when the charges are 1m apart. Therefore, the equation becomes:
1 = k Q1 Q2 / 1² or k Q1 Q2 = 1 --------(2[tex]1 = k Q1 Q2 / 1² or k Q1 Q2 = 1 --------(2[/tex])
F = k Q1 Q2 / r²where r = 0.25m
Putting k Q1 Q2 = 1 from equation (2)
above in the equation above gives
[tex]:F = 1 / r² = 1 / (0.25)²= 1 / 0.0625= 16[/tex]N
To know more about charges visit:
https://brainly.com/question/28721069
#SPJ11
If you put a flame under a 3 liter container of water and its temperature increases by 4 °C in a certain amount of time, how much will the temperature increase in the same amount of time if you put the same flame under a 6 liter container of water?
.
Group of answer choices
8 °C, since it's capacity for heat has doubled.
4 °C, since it's still just water with the same heat capacity.
2 °C, since it's twice as much water.
The temperature increase in the same amount of time if you put the same flame under a 6-liter container of water is 2 °C, since it's twice as much water.
If you put a flame under a 3-liter container of water and its temperature increases by 4 °C in a certain amount of time, the temperature increase in the same amount of time, if you put the same flame under a 6-liter container of water, is 2 °C, since it's twice as much water.
Key concept: The amount of heat required to raise the temperature of a substance depends on its mass and the specific heat capacity of the substance. The specific heat capacity of water is 4.184 J/g°C, which means that it takes 4.184 Joules of energy to raise the temperature of one gram of water by one degree Celsius.
If a flame is used to heat a 3-liter container of water, it will take a certain amount of heat to increase the temperature of the water by 4°C. If the same flame is used to heat a 6-liter container of water, it will take twice as much heat to increase the temperature of the water by the same amount.
To know more about Key concept please refer to:
https://brainly.com/question/30783585
#SPJ11
When the voltage of the secondary is the same as the voltage of the primary, it is said to be a transformer of:
A. Neither high nor low
B. Discharge
C. There is not enough information to answer.
D. Fall
When the voltage of the secondary is the same as the voltage of the primary, it is said to be a transformer of Neither high nor low voltage.
What is a transformer?A transformer is an electromagnetic gadget that is utilized to alter the voltage of an AC supply while keeping up with its force rating. It is a static gadget that comprises two copper loops or windings wound around a typical core. The transformation in voltage is accomplished by electromagnetic acceptance from one curl to the next.The two basic sorts of transformers are step-up and step-down transformers. A step-up transformer builds the voltage in the optional loop concerning the essential curl, while a step-down transformer lessens the voltage in the auxiliary winding concerning the essential curl.
learn more about voltage here
https://brainly.com/question/27861305
#SPJ11
Homework-3 Question 1: A cam is to give the following motion to a knife-edge follower: 1 Outstroke during \( 30^{\circ} \) of cam rotation: 2 Dwell for the next \( 60^{\circ} \) of cam rotation : 3. R
Cam is a mechanical device that is used to convert rotary motion into linear motion. The cam follower mechanism is used to convert the rotary motion of a cam into a reciprocating motion of a follower. It consists of a cam and a follower. The cam is a rotating element that imparts a specified motion to the follower.
The follower is a sliding element that follows the motion of the cam.
Cam specifications for knife-edge follower motion: Outstroke during 30° of cam rotation: During the first 30° of cam rotation, the cam must provide the follower with a motion that moves it away from the cam centerline.2 Dwell for the next 60° of cam rotation: During the next 60° of cam rotation, the follower must remain in its outstroke position.
3. Return Stroke for the remaining 270° of cam rotation:
The cam must now provide a motion to the follower that moves it back towards the cam centerline. The return stroke motion should be such that the follower returns to its initial position by the end of 360° of cam rotation.
In conclusion, this is the cam specification for a knife-edge follower motion:
1 Outstroke during 30° of cam rotation:
2 Dwell for the next 60° of cam rotation :
3. Return Stroke for the remaining 270° of cam rotation.
To learn more about motion visit;
https://brainly.com/question/2748259
#SPJ11
4. Find the position (x, y) and angle relative to +at which a proton moving at 6.0 x 10m/s emerges from the 0.25T magnetic field "out of the page having width 15.0cm. (the field extends infinitely in the ty directions]
To find the position (x, y) and angle relative to the positive x-axis at which the proton emerges from the magnetic field, we can use the principles of magnetic field motion.
Given:
Initial velocity of the proton, v = 6.0 x 10^6 m/s
Magnetic field strength, B = 0.25 T
Width of the magnetic field, w = 15.0 cm = 0.15 m
Since the magnetic field is perpendicular to the page, the proton will experience a centripetal force due to the Lorentz force. This force causes the proton to move in a circular path inside the magnetic field.
The centripetal force is given by the equation:
F_c = (m*v^2) / r
The magnetic force experienced by the proton is given by the equation:
F_m = q * v * B
Setting the centripetal force equal to the magnetic force, we have
(m*v^2) / r = q * v * B
Simplifying the equation and solving for the radius of the circular path:
r = (mv) / (qB)
Now, we can find the angle θ at which the proton emerges from the magnetic field. The angle can be determined using trigonometry:
θ = tan^(-1)(y/x)
Finally, we can find the position (x, y) using the radius of the circular path and the width of the magnetic field
x = r + w/2
y = 0
Substituting the given values into the equations, we can calculate the position (x, y) and angle θ at which the proton emerges from the magnetic field.
To learn more about, Magnetic Field, click here, https://brainly.com/question/14848188
#SPJ11
a) With the aid of circuit diagram explain the operation of first quadrant chopper.
b) Explain the principle of operation of second quadrant chopper.
c) A 220 V, 1500 rev/min, 25 A permanent-magnet dc motor has an armature resistance of 0.3 Q. The motor's speed is controlled with the first quadrant dc chopper. Calculate the chopper's duty ratio that yields a motor speed of 750 rev/minat rated torque.
The duty ratio of a chopper cannot be negative, so we will have to flip the switch and convert it to a first-quadrant chopper with a duty ratio of 0.067.
a) Operation of first quadrant chopper:
The first-quadrant chopper operates in the first quadrant of the i-v plane. When an SCR is used as the switching component, it is generally referred to as a first-quadrant SCR chopper.
b) Principle of operation of second quadrant chopper:
When a step-down converter is used to regulate the average output voltage to less than the input voltage, it is known as a second-quadrant chopper.
Because the circuit operates in the second quadrant of the i-v plane, it is referred to as a second-quadrant chopper. It's usually used for speed control in DC motors.
A four-quadrant chopper is a combination of a first-quadrant and a second-quadrant chopper, which can operate in all four quadrants of the i-v plane.
c) Calculation of the chopper's duty ratio:
A 220 V, 1500 rev/min, 25 A permanent magnet DC motor has an armature resistance of 0.3 Q.
We know that N = (120f)/p,
where f is the frequency and p is the number of poles. If we consider the frequency to be 50Hz and the number of poles to be 4, we obtain the following:
N = (120 × 50)/4
= 1500 rpm
We can also calculate the motor's back emf, which is given by the equation
Eb = (V - IaRa),
where V is the applied voltage, Ia is the armature current, and Ra is the armature resistance. Here, we can calculate the back emf as follows:
Eb = (220 - 25 × 0.3)
= 212.5 V
At rated torque, the motor's speed is 1500 rpm. We can also calculate the duty ratio of the chopper, which is given by the following formula:
D = (Eba - V)/Eba,
where Eba is the motor's back emf at rated speed. If we assume that the speed is halved, or 750 rpm, we can calculate the new back emf as follows:
Eba' = (N'/N) × Eba
= (750/1500) × 212.5
= 106.25 V
The duty ratio can now be calculated as follows:
D = (Eba' - V)/Eba'
= (106.25 - 220)/106.25
= -1.067
The duty ratio of a chopper cannot be negative, so we will have to flip the switch and convert it to a first-quadrant chopper with a duty ratio of 0.067.
Learn more about ratio from the given link
https://brainly.com/question/12024093
#SPJ11
